Yamaha Welding System generator User Manual

Generator  
OWNER’S MANUAL  
Read this manual carefully before operating this machine.  
EF2000iS  
LIT-19626-01-53  
7DK-28199-10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00002  
INTRODUCTION  
Congratulations on your purchase of your new Yamaha.  
This manual will provide you with a good basic understanding of the operation and main-  
tenance of this machine.  
If you have any questions regarding the operation or maintenance of your machine,  
please consult a Yamaha dealer.  
AE00022  
EF2000iS  
OWNER’S MANUAL  
© 2009 by Yamaha Motor Corporation, U.S.A.  
1st Edition, January 2009  
All rights reserved.  
Any reprinting or unauthorized use  
without the written permission of  
Yamaha Motor Corporation, U.S.A.  
is expressly prohibited.  
Printed in Japan  
P/N LIT-19626-01-53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPOTANT MANUAL INFORMATION  
Particularly important information is distin-  
guished in this manual by the following  
notations.  
This is the safety alert symbol. It is  
used to alert you to potential personal  
injury hazards. Obey all safety mes-  
AE00032  
sages that follow this symbol to avoid  
possible injury or death.  
WARNING  
PLEASE READ AND UNDERSTAND  
THIS MANUAL COMPLETELY BEFORE  
OPERATING THE MACHINE.  
WARNING  
A WARNING indicates a hazardous situ-  
ation which, if not avoided, could result  
in death or serious injury.  
TIP  
9 Yamaha continually seeks advance-  
ments in product design and quality.  
Therefore, while this manual contains  
the most current product information  
available at the time of printing, there  
may be minor discrepancies between  
your engine and this manual. If there is  
any question concerning this manual,  
please consult a Yamaha dealer.  
9 This manual should be considered a  
permanent part of this engine and  
should remain with this engine when  
resold.  
NOTICE  
A NOTICE indicates special precau-  
tions that must be taken to avoid dam-  
age to the machine or other property.  
TIP  
A TIP provides key information to make  
procedures easier or clearer.  
* Product and specifications are subject to  
change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00041  
CONTENTS  
SAFETY INFORMATION.........................1  
EXHAUST FUMES ARE  
Application range................................20  
PERIODIC MAINTENANCE..................21  
Maintenance chart..............................21  
Spark plug inspection.........................23  
Carburetor adjustment........................24  
Engine oil replacement.......................24  
Air filter ...............................................26  
Muffler screen and spark arrester......27  
Fuel tank filter.....................................29  
STORAGE .............................................30  
Drain the fuel......................................30  
Engine ................................................32  
TROUBLESHOOTING...........................33  
Engine won’t start...............................33  
Generator won’t produce power.........34  
SPECIFICATIONS.................................36  
Dimensions.........................................36  
Engine ................................................36  
Generator ...........................................36  
CONSUMER INFORMATION................37  
Identification number records.............37  
Machine identification.........................37  
LIMITED WARRANTY (EF- AND  
POISONOUS........................................1  
FUEL IS HIGHLY FLAMMABLE AND  
POISONOUS........................................1  
ENGINE AND MUFFLER MAY BE  
HOT......................................................1  
ELECTRIC SHOCK PREVENTION .....2  
CONNECTION NOTES........................3  
CONNECTION .....................................3  
EXTENSION CORD NOTES................3  
LOCATION OF IMPORTANT  
LABELS...................................................4  
DESCRIPTION ........................................6  
Control Panel........................................6  
CONTROL FUNCTION............................7  
Engine switch .......................................7  
Oil warning light (Red)..........................7  
DC protector.........................................7  
Economy control switch........................8  
AC pilot light (Green)............................8  
Overload indicator light (Red) ..............9  
Fuel tank cap........................................9  
Fuel tank cap air vent knob................10  
Fuel cock knob ...................................10  
Ground (Earth) terminal .....................10  
Twin Tech............................................10  
PREPARATION .....................................11  
Fuel.....................................................11  
Engine oil............................................12  
PRE-OPERATION CHECK ...................13  
Pre-operation check ...........................13  
OPERATION..........................................14  
Starting the engine.............................14  
Stopping the engine ...........................16  
Connection .........................................17  
Battery charging .................................18  
EDL-SERIES) ........................................38  
EXHAUST EMISSION CONTROL  
SYSTEM AND COMPONENTS .........40  
WIRING DIAGRAM ...............................41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00071  
SAFETY INFORMATION  
AE00072  
EXHAUST FUMES ARE POISONOUS  
9 Never operate the engine in a closed area or it may  
cause unconsciousness and death within a short  
time. Operate the engine in a well ventilated area.  
7DK-001  
7DK-002  
7DK-003  
AE00075  
FUEL IS HIGHLY FLAMMABLE AND  
POISONOUS  
9 Always turn off the engine when refuelling.  
9 Never refuel while smoking or in the vicinity of an  
open flame.  
9 Take care not to spill any fuel on the engine or muf-  
fler when refueling.  
9 If you swallow any fuel, inhale fuel vapor, or allow  
any to get in your eye(s), see your doctor immedi-  
ately. If any fuel spills on your skin or clothing,  
immediately wash with soap and water and change  
your clothes.  
9 When operating or transporting the machine, be  
sure it is kept upright. If it tilts, fuel may leak from  
the carburetor or fuel tank.  
7DK-004  
AE00843  
ENGINE AND MUFFLER MAY BE HOT  
9 Place the machine in a place where pedestrians or  
children are not likely to touch the machine.  
7DK-005  
9 Avoid placing any flammable materials near the  
exhaust outlet during operation.  
7DK-006  
– 1 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9 Keep the machine at least 1 m (3 ft) from buildings  
a
or other equipment, or the engine may overheat.  
a 1 m (3 ft)  
7DK-007  
9 Do not operate the engine with a dust cover or  
other objects covering it.  
9 When covering the generator, be sure to do so only  
after the engine and muffler have completely  
cooled down.  
7DK-008a  
9 Be sure to carry the generator only by its carrying  
handles 1.  
1
7DK-036  
9 Do not place any obstacles on the generator.  
AE00083  
ELECTRIC SHOCK PREVENTION  
9 Never operate the engine in rain or snow.  
7DK-009  
9 Never touch the machine with wet hands or electri-  
cal shock will occur.  
7DK-010  
2 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9 Connect the ground lead of the machine to the  
ground (Earth) terminal 1 and connect the end to  
the ground electrode buried in the ground.  
1
7DK-011  
AE00088  
CONNECTION NOTES  
9 Avoid connecting the generator to commercial  
power outlet.  
9 Avoid connecting the generator in parallel with any  
other generator.  
1
2
1
2
1 Correct  
2 Incorrect  
AE00091  
CONNECTION  
WARNING  
Before the generator can be connected to a build-  
ings electrical system, a licensed electrician must  
install an isolation (transfer) switch in the build-  
ings main fuse box. The switch is the connection  
point for generator power and allows selection of  
generator or main line power to the building. This  
will prevent the generator from charging the main  
power line (backfeeding) when the main power sup-  
ply has failed or has been turned off for line repair.  
Backfeeding can electrocute or injure line mainte-  
nance personnel. Also, generator and building  
electrical system damage can occur when normal  
operating power returns if unit is used without an  
isolation switch.  
7DK-012  
AE00086  
EXTENSION CORD NOTES  
Extension cords should be protected by a tough flexible  
rubber sheath (IEC 245) or the equivalent to withstand  
mechanical stresses.  
3 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00062  
LOCATION OF IMPORTANT LABELS  
Please read the following labels carefully before oper-  
ating this machine.  
TIP  
Maintain or replace safety and instruction labels, as  
necessary.  
1
2
3
4
6
5
7DK-013  
7DK-014  
1
DANGER  
Using a generator indoors CAN KILL YOU IN MINUTES.  
Generator exhaust contains carbon monoxide.  
This is a poison you cannot see or smell.  
NEVER use inside a home Only use OUTSIDE and  
or garage, EVEN IF doors far away from windows,  
and windows are open.  
door, and vents.  
4 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
q
WARNING  
Read the owners manual and all labels before operating.  
Only operate in well-ventilated areas. Exhaust gas contains poisonous carbon monoxide.  
Check for spilled fuel or fuel leaks.  
8
8
8
8
8
8
8
Stop engine before refueling.  
Do not operate near flammable materials.  
Electrocution can occur if generator is used in rain, snow, or near water. Keep this unit dry at all times.  
Electrocution or property damage can occur: Do not connect this generator to any buildings electrical  
system unless an isolation switch has been installed by a licensed electrician. Refer to the owners manual.  
When operating the generator:  
8
Never place a partition or other barrier around the generator.  
Do not cover the generator with a box.  
7DK-24162-10  
Do not place any objects on the generator.  
3
4
NOTICE  
Use the specified spark plug only.  
HOT EXHAUST  
7WL-28176-10  
Specified plug:BPR6HS(NGK)  
5
Important Emissions Information  
The air index of this engine is 3  
(California only)  
YAMAHA MOTOR POWERED PRODUCTS CO.,LTD.  
This engine meets **** California exhaust and evaporative  
emission regulations for small off-road engines.  
This engine conforms to Phase 2 U.S.EPA regulations for  
small nonroad engines.  
0
2
4
6
8
10  
MOST CLEAN  
LEAST CLEAN  
Note:The lower the air index, the less the pollution.  
This engine is certified to be emissions compliant  
for the following use:  
EMISSIONS COMPLIANCE PERIOD : CATEGORY A(EPA)  
EF: *********  
DISPLACEMENT: *** cc  
EVAP F: ********  
EMISSION CONTROL SYSTEM: EM  
This engine is certified to operate on unleaded gasoline.  
ENGINE OIL: SAE10W-30 TYPE: SE  
No other adjustments needed.  
MODERATE  
(*** HOURS)  
Check owner's manual for further details.  
INTERMEDIATE  
(*** HOURS)  
EXTENDED  
(*** HOURS)  
X
6
OIL  
EF2000IS  
AC output  
Rated  
60Hz  
1.6kVA  
120V  
Phase  
DC output  
Fuel  
Single  
12V 8A  
Gasoline  
YAMAHA MOTOR POWERED PRODUCTS CO.,LTD.  
7DK-24164-10  
MADE IN JAPAN  
5 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DESCRIPTION  
1
5
2
1 Carrying handle  
2 Fuel tank cap air vent knob  
3 Fuel tank cap  
4 Recoil starter  
5 Fuel gauge  
3
6
6 Muffler  
7 Oil filler cap  
4
7
7DK-015  
7DK-016  
1
2 3  
4 5  
AE00103  
Control panel  
1 Oil warning light  
2 AC pilot light  
6
3 Overload indicator light  
4 Economy control switch  
(Black)  
7
8
5 Engine switch (Red)  
6 Fuel cock knob  
7 Choke knob  
8 Twin Tech (parallel running  
terminal)  
w
9 AC receptacle  
0 DC protector (breaker)  
q Ground (Earth) terminal  
w DC receptacle  
9
7DK-017  
q
0
6 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00101  
CONTROL FUNCTION  
AE00121  
Engine switch  
The engine switch controls the ignition system.  
2
1
7DK-018  
1 7 ON”  
Ignition circuit is switched on.  
The engine can be started.  
2 5 STOP”  
Ignition circuit is switched off.  
The engine will not run.  
AE00111  
Oil warning light (Red)  
When the oil level falls below the lower level, the oil  
warning light comes on and then the engine stops auto-  
matically. Unless you refill with oil, the engine will not  
start again.  
TIP  
If the engine stalls or does not start, turn the engine  
switch to ONand then pull the recoil starter. If the oil  
warning light flickers for a few seconds, the engine oil is  
insufficient. Add oil and restart.  
700-115  
DC protector  
The DC protector turns off 2 automatically when elec-  
tric device being connected to the generator is operat-  
ing and current above the rated flows.To use this equip-  
ment again, turn on the DC protector by pressing its  
button to ON1.  
1 ON”  
Direct current is output. (This is the default position.)  
2 OFF”  
Direct current is not output.  
1
2
7DK-052  
7 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTICE  
Reduce the load of the connected electric device  
below the specified rated output of the generator if  
the DC protector turns off. If the DC protector turns  
off again, stop using the device immediately and  
consult a Yamaha dealer.  
AE00142  
Economy control switch  
1 I ON”  
2
When the economy control switch is turned to ON1,  
the economy control unit controls the engine speed  
according to the connected load. The results are better  
fuel consumption and less noise.  
1
7DK-020  
2 3 OFF”  
When the economy control switch is turned to OFF2,  
the engine runs at the rated r/min (4,500 r/min) regard-  
less of whether is a load connected or not.  
TIP  
The economy control switch must be turned to OFF2  
when using electric devices that require a large starting  
current, such as a compressor of a submergible pump.  
AC pilot light (Green)  
The AC pilot light 1 comes on when the engine starts  
and produces power.  
1
7DK-048  
8 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE01087  
Overload indicator light (Red)  
The overload indicator light 1 comes on when an over-  
load of a connected electrical device is detected, the  
inverter control unit overheats, or the AC output voltage  
rises. Then, the AC protector will trip, stopping power  
generation in order to protect the generator and any  
connected electric devices. The AC pilot light (Green)  
will go off and the overload indicator light (Red) will stay  
on, but the engine will not stop running.  
1
7DK-021  
When the overload indicator light comes on and power  
generation stops, proceed as follows:  
1. Turn off any connected electric devices and stop  
the engine.  
2. Reduce the total wattage of connected electric  
devices within the rated output.  
3. Check for blockages in the cooling air inlet and  
around the control unit. If any blockages are found,  
remove.  
4. After checking, restart the engine.  
TIP  
The overload indicator light may come on for a few sec-  
onds at first when using electric devices that require a  
large starting current, such as a compressor or a sub-  
mergible pump. However, this is not a malfunction.  
Fuel tank cap  
Remove the fuel tank cap by turning it counterclock-  
wise.  
7DK-022  
9 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Fuel tank cap air vent knob  
The fuel tank cap 2 is provided with an air vent knob  
1 to stop fuel flow.  
2
The air vent knob must be turned to ON. This will  
allow fuel to flow to the carburetor and the engine to  
run. When the engine is not in use, turn the air vent  
knob to OFFto stop fuel flow.  
1
7DK-023  
Fuel cock knob  
The fuel cock supplies fuel from the fuel tank to the car-  
buretor.  
2
1
The fuel cock has two positions.  
1 ON”  
7DK-024  
With the knob in this position, fuel flows to the carbure-  
tor. Normal using is done with the knob in this position.  
2 OFF”  
With the knob in this position, fuel will not flow. Always  
turn the knob to this position when the engine is not  
running.  
Ground (Earth) terminal  
Ground (Earth) terminal 1 connects the earth line for  
prevention of electric shock.  
When the electric device is earthed, always the gener-  
ator must be earthed.  
1
7DK-011  
Twin Tech  
(Terminal for Connecting special cables for  
parallel running)  
This is the terminal for connecting special cables for  
parallel running of two EF2000iS. The parallel running  
requires two EF2000iS and the special cables. (The  
rated output in parallel running is 3.0 kVA and the rated  
current is 25.0 A.)  
7DK-042a  
The handling, operation procedure and the notes on  
usage are described in the PARALLEL RUNNING KIT  
OWNERS MANUAL included in the Parallel Running  
Kit. Consult a Yamaha dealer for this Parallel Running  
Kit.  
10 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PREPARATION  
AE00856  
Fuel  
WARNING  
9 Fuel is highly flammable and poisonous. Check  
SAFETY INFORMATION(See page 1) careful-  
ly before filling.  
7DK-026  
9 Do not overfill the fuel tank, otherwise it may  
overflow when the fuel warms up and expands.  
9 After fill the fuel, make sure the fuel tank cap is  
tightened securely.  
7DK-091  
NOTICE  
9 Immediately wipe off spilled fuel with a clean,  
dry, soft cloth, since fuel may deteriorate paint-  
ed surfaces or plastic parts.  
9 Use only unleaded gasoline. The use of leaded  
gasoline will cause severe damage to internal  
engine parts.  
707-095  
Remove the fuel tank cap and fill the fuel into the tank  
up to the red level 2.  
2
The fuel level in the fuel tank can be checked through  
the fuel level gauge 1.  
1 Fuel level gauge  
2 Red line  
1
7DK-037  
3 Fuel level  
3
Recommended fuel:  
Unleaded gasoline  
Fuel tank capacity:  
Total:  
4.2 L (1.11 US gal, 0.92 Imp gal)  
7DK-028  
4 F”  
5 E”  
Full  
Empty  
4
5
Your Yamaha engine has been designed to use regular  
unleaded gasoline with a pump octane number ((R +  
M)/2) of 86 or higher, or research octane number of 91  
or higher.  
7DK-093  
11 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00222  
Engine oil  
NOTICE  
The generator has been shipped without engine oil.  
Do not start the engine till fill with the sufficient  
engine oil.  
1. Place the generator on a level surface.  
2. Remove the screws 1, and then remove the cover  
2.  
1
2
7DK-030  
3. Remove the oil filler cap 1.  
1
7DK-031  
4. Fill the specified amount of the recommended  
engine oil, and then install and tighten the oil filler  
cap.  
7DK-033  
1 Upper level  
1
Recommended engine oil:  
å
YAMALUBE 4 (10W-40),  
SAE 10W-30 or 10W-40  
SAE #30  
SAE #20  
SAE 10W  
700-119  
ç
0°C  
25°C  
å
Recommended engine oil grade:  
API Service SE type or higher  
Engine oil quantity:  
YAMALUBE 4 (10W-40)  
ç
SAE 10W  
SAE #20  
SAE #30  
0.4 L (0.42 US qt, 0.35 lmp qt)  
32°F  
80°F  
5. Install the cover and tighten the screws.  
12 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00845  
PRE-OPERATION CHECK  
WARNING  
If any item in the Pre-operation check is not work-  
ing properly, have it inspected and repaired before  
operating the generator.  
The condition of a generator is the owner's responsibil-  
ity. Vital components can start to deteriorate quickly  
and unexpectedly, even if the generator unused.  
TIP  
Pre-operation checks should be made each time the  
generator is used.  
Pre-operation check  
Fuel (See page 11)  
9 Check fuel level in fuel tank.  
9 Refuel if necessary.  
Fuel line  
9 Check fuel hose for crack or damage.  
9 Replace if necessary.  
Engine oil (See page 12)  
9 Check oil level in engine.  
9 If necessary, add recommended oil to specified  
level.  
9 Check generator for oil leakage.  
The point where abnormality was recognized by  
use  
9 Check operation.  
9 If necessary, consult a Yamaha dealer.  
13 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00846  
OPERATION  
WARNING  
9 Never operate the engine in a closed area or it  
may cause unconsciousness and death within  
a short time. Operate the engine in a well venti-  
lated area.  
7DK-047  
9 Before starting the engine, do not connect any  
electric devices.  
NOTICE  
The generator has been shipped without engine oil.  
Do not start the engine till fill with the sufficient  
engine oil.  
Starting the engine  
1. Turn the economy control switch (Black) to OFF”  
1.  
1
7DK-034  
1 3 OFF”  
2. While holding the fuel tank cap so that it will not  
move, turn the air vent knob to ON1.  
1 Air vent knob  
1
7DK-035  
3. Turn the fuel cock knob to ON1.  
1 ON”  
1
7DK-038  
4. Turn the engine switch (Red) to ON1.  
1 7 ON”  
1
7DK-039  
14 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Pull the choke knob 1 fully out.  
1
1 Choke knob  
TIP  
The choke is not required to start a warm engine.  
Push the choke knob in to the original position.  
7DK-040  
6. Pull slowly on the recoil starter until it is engaged,  
then pull it briskly.  
TIP  
Grasp the carrying handle firmly to prevent the genera-  
tor from falling over when pulling the recoil starter.  
7DK-041  
7. After the engine starts, warm up the engine until  
the engine does not stop when the choke knob is  
returned to the original position.  
TIP  
When starting the engine, with the economy control  
switch ON, and there is no load on the generator:  
9 in ambient temperature below 0°C (32°F), the  
engine will run at the rated r/min (4,500 r/min) for 5  
minutes to warm up the engine.  
7DK-042  
9 in ambient temperature below 5°C (41°F), the  
engine will run at the 4,500 r/min for 3 minutes to  
warm up the engine.  
The economy control unit operates normally after the  
above time period, while the economy control switch is  
ON.  
15 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE01025  
Stopping the engine  
TIP  
Turn off any electric devices.  
1
7DK-034  
1. Turn the economy control switch (Black) to OFF”  
1.  
1 3 OFF”  
2. Disconnect any electric devices.  
7DK-047  
3. Turn the engine switch (Red) to STOP1.  
1 5 STOP”  
1
7DK-044  
4. Turn the fuel cock knob to OFF1.  
1 OFF”  
1
7DK-045  
5. Turn the fuel tank cap air vent knob to OFF1  
after the engine has completely cooled down.  
1
7DK-092  
16 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00839  
Connection  
Alternating Current (AC)  
WARNING  
Be sure any electric devices are turned off before  
plugging them in.  
NOTICE  
9 Be sure all electric devices including the lines  
and plug connections are in good condition  
before connection to the generator.  
9 Be sure the total load is within generator rated  
output.  
9 Be sure the receptacle load current is within  
receptacle rated current.  
TIP  
Make sure to ground (Earth) the generator.  
When the electric device is earthed, always the gener-  
ator must be earthed.  
1. Start the engine.  
2. Plug in to AC receptacle.  
7DK-043  
7DK-048  
7DK-049  
3. Make sure the AC pilot light 1 is on.  
1 AC pilot light  
1
4. Turn the economy control switch to ON1.  
1 I ON”  
5. Turn on any electric devises.  
TIP  
1
The economy control switch must be turned to OFFto  
increase engine speed to rated rpm.  
17 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Battery Charging  
TIP  
9 The generator DC rated voltage is 12V.  
9 Start the engine first, and then connect the gener-  
ator to the battery for charging.  
9 Before starting to charge the battery, make sure  
that the DC protector is turned on.  
1 Red wire  
2 Black wire  
2
1
1. Start the engine.  
2. Connect the red battery charger lead to the posi-  
tive (+) battery terminal.  
762-040  
3. Connect the black battery charger lead to the neg-  
ative (-) battery terminal.  
4. Turn the economy control switch off to start battery  
charging.  
NOTICE  
9 Be sure the economy control switch is turned  
off while charging the battery.  
762-041  
9 Be sure to connect the red battery charger lead  
to the positive (+) battery terminal, and connect  
the black lead to the negative (-) battery termi-  
nal. Do not reverse these positions.  
9 Connect the battery charger leads to the bat-  
tery terminals securely so that they are not dis-  
connected due to engine vibration or other dis-  
turbances.  
9 Charge the battery in the correct procedure by  
following instructions in the owners manual  
for the battery.  
9 The DC protector turns off 2 automatically if  
current above the rated flows during battery  
charging.  
1
2
7DK-052  
To restart charging the battery, turn the DC pro-  
tector on by pressing its button to ON1. If  
the DC protector turns off again, stop charging  
the battery immediately and consult a Yamaha  
dealer.  
1 ON”  
2 OFF”  
18 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TIP  
9 Follow instructions in the owners manual for the  
battery to determine the end of battery charging.  
9 Measure the specific gravity of electrolyte to deter-  
mine if the battery is fully charged. At full charge,  
the electrolyte specific gravity is between 1.26 and  
1.28.  
9 It is advisable to check the specific gravity of the  
electrolyte at least once every hour to prevent over-  
charging the battery.  
WARNING  
Never smoke or make and break connections at the  
battery while charging. Sparks may ignite the bat-  
tery gas.  
Battery electrolyte is poisonous and dangerous,  
causing severe burns, etc. contains sulfuric (sul-  
phuric) acid. Avoid contact with skin, eyes or cloth-  
ing.  
Antidote:  
EXTERNAL-Flush with water.  
INTERNAL-Drink large quantities of water or milk.  
Follow with milk of magnesia, beaten egg or veg-  
etable oil. Call physician immediately.  
EYES: Flush with water for 15 minutes and get  
prompt medical attention. Batteries produce explo-  
sive gases. Keep sparks, flame, cigarettes, etc.,  
away. Ventilate when charging or using in closed  
space. Always cover eyes when working near bat-  
teries. KEEP OUT OF REACH OF CHILDREN.  
762-012  
19 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00812  
Application range  
When using the generator, make sure the total load is within rated output of a generator.  
Otherwise, generator damage may occur.  
DC  
AC  
0.40.75  
Power factor  
EF2000iS  
1
0.80.95  
1,280W  
(Efficiency 0.85)  
Rated voltage  
12V  
Rated current  
8A  
1,600W  
544W  
TIP  
9 “–” means below.  
9 Application wattage indicates when each device is  
used by itself.  
9 The simultaneous usage of AC and DC power is  
possible but total wattage should not exceed the  
rated output.  
EX:  
Generator rated output  
Frequency Power factor  
1,600VA  
1.0  
0.8  
1,500W  
1,180W  
96W  
AC  
DC  
1
(12V/8A)  
9 The overload indicator light 1 comes on when  
total wattage exceeds the application range. (See  
page 9 for more details.)  
7DK-021  
NOTICE  
9 Do not overload.The total load of all electrical appliances must not exceed the  
supply range of the generator. Overloading will damage the generator.  
9 When supplying precision equipment, electronic controllers, PCs, electronic  
computers, microcomputerbased equipment or battery chargers, keep the gen-  
erator a sufficient distance away to prevent electrical interference from the  
engine. Also ensure that electrical noise from the engine does not interfere  
with any other electrical devices located near the generator.  
9 If the generator is to supply medical equipment, advice should first be obtained  
from the manufacturer, a medical professional or hospital.  
9 Some electrical appliances or general-purpose electric motors have high start-  
ing currents, and cannot therefore be used, even if they lie within the supply  
ranges given in the above table. Consult the equipment manufacturer for fur-  
ther advice.  
20 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00401  
PERIODIC MAINTENANCE  
Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will  
keep your generator in the safest and most efficient condition possible. The most impor-  
tant points of generator inspection, adjustment, and lubrication are explained on the fol-  
lowing pages.  
WARNING  
If you are not familiar with maintenance work, have a Yamaha dealer do it for you.  
AE00403  
Maintenance chart  
WARNING  
Stop the engine before starting maintenance work.  
NOTICE  
Use only Yamaha specified genuine parts for replacement. Ask an authorized  
Yamaha dealer for further attention.  
Every  
Pre-  
operation  
check  
Item  
Routine  
6 months 12 months  
or 100 Hr or 300 Hr  
Check condition.  
Spark plug  
1
Clean and replace if necessary.  
Check fuel level and leakage.  
Fuel  
1
1
1
Fuel hose  
Check fuel hose for cracks or damage.  
Replace if necessary.  
Check oil level in engine.  
Replace  
Engine oil  
1(*1)  
1(*2)  
Check condition.  
Air filter element  
Muffler screen  
Clean  
Check condition.  
1
Clean and replace if necessary.  
Check condition.  
Spark arrester  
Fuel filter  
1
Clean and replace if necessary.  
Clean and replace if necessary.  
1
21 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Every  
Pre-  
operation  
check  
Item  
Routine  
6 months 12 months  
or 100 Hr or 300 Hr  
Check breather hose for cracks or  
Crankcase breather  
hose  
damage.  
1
Replace if necessary.  
Decarbonize cylinder head.  
More frequently if necessary.  
Check and adjust when engine is cold.  
Check all fittings and fasteners.  
Correct if necessary.  
Cylinder head  
#
#
#
Valve clearance  
Fittings / fasteners  
The point where abnormality was recognized by use  
1
*1·····Initial replacement of the engine oil is after one month or 20 hours of operation.  
*2·····The air filter element needs to be cleaned more frequently when using in unusually wet or dusty areas.  
#····· Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.  
22 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Spark plug inspection  
The spark plug is important engine components, which  
should be checked periodically.  
1. Remove the screws 1, and then remove the cover  
2.  
1
2
7DK-030  
2. Remove the spark plug cap 3 and cap 4, and  
insert the tool 5 through the hole from the outside  
of the cover.  
4
3
7DK-053  
3. Insert the handlebar 6 into the tool 5 and turn it  
6
5
counterclockwise to remove the spark plug.  
7DK-054  
4. Check for discoloration and remove the carbon.  
The porcelain insulator around the center elec-  
trode of spark plug should be a medium-to-light tan  
color.  
5. Check the spark plug type and gap a.  
Standard Spark Plug:  
BPR6HS (NGK)  
Spark Plug Gap a:  
a
0.60.7 mm (0.0240.028 in)  
760-001a  
TIP  
The spark plug gap should be measured with a wire  
thickness gauge and, if necessary, adjusted to specifi-  
cation.  
23 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Install the spark plug.  
Spark Plug Torque:  
20.0 Nm (2.0 kgfm, 14.8 lbfft)  
TIP  
If a torque wrench is not available when installing a  
spark plug, a good estimate of the correct torque is 1/4-  
1/2 turn past finger tight. However, the spark plug  
should be tightened to the specified torque as soon as  
possible.  
7. Install the spark plug cap and cap.  
8. Install the cover and tighten the screws.  
AE00431  
Carburetor adjustment  
The carburetor is a vital part of the engine. Adjusting  
should be left to a Yamaha dealer with the professional  
knowledge, specialized data, and equipment to do so  
properly.  
AE00412  
Engine oil replacement  
WARNING  
Avoid draining the engine oil immediately after  
stopping the engine. The oil is hot and should be  
handled with care to avoid burns.  
1. Place the generator on a level surface and warm  
up the engine for several minutes.  
Then stop the engine and turn the fuel cock knob,  
fuel tank cap air vent knob to OFF.  
2. Remove the screws 1 and then remove the cover  
2.  
1
2
7DK-030  
3. Remove the oil filler cap 1.  
1
7DK-031  
24 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. Place an oil pan under the engine. Tilt the genera-  
tor to drain the oil completely.  
5. Replace the generator on a level surface.  
NOTICE  
Do not tilt the generator when adding engine oil.  
This could result in overfilling and damage to the  
engine.  
7DK-055  
7DK-033  
6. Add engine oil to the upper level 1.  
Recommended engine oil:  
q
å
YAMALUBE 4 (10W-40),  
SAE 10W-30 or 10W-40  
SAE #30  
SAE #20  
SAE 10W  
ç
700-006a  
0°C  
25°C  
Recommended engine oil grade:  
API Service SE type or higher  
Engine oil quantity:  
å
YAMALUBE 4 (10W-40)  
0.4 L (0.42 US qt, 0.35 lmp qt)  
ç
SAE 10W  
SAE #20  
SAE #30  
32°F  
80°F  
7. Wipe the cover clean, and wipe up any spilled oil.  
NOTICE  
Be sure no foreign material enters the crankcase.  
8. Install the oil filler cap.  
9. Install the cover 2 and tighten the screws 1.  
1
2
7DK-030  
25 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE01084  
Air filter  
1. Remove the screws 1, and then remove the cover  
2.  
1
2
7DK-030  
2. Remove the screw 1 and then remove the air filter  
case cover 2.  
2
7DK-061  
1
3. Remove the foam element 1.  
4. Wash the foam element in solvent and dry it.  
5. Oil the foam element and squeeze out excess oil.  
The foam element should be wet but not dripping.  
1
Recommended oil:  
Foam-air-filter oil or SAE #20 motor oil  
NOTICE  
Do not wring out the foam element when squeezing  
it. This could cause it to tear.  
6. Insert the foam element into the air filter case.  
TIP  
Be sure the foam element sealing surface matches the  
air filter so there is no air leak.  
NOTICE  
7DK-062  
The engine should never run without the foam ele-  
ment; excessive piston and cylinder wear may  
result.  
7. Install the air filter case cover in its original position  
and tighten the screw.  
8. Install the cover and tighten the screws.  
26 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE01075  
Muffler screen and spark arrester  
WARNING  
The engine and muffler will be very hot after the  
engine has been run.  
7DK-026  
Avoid touching the engine and muffler while they  
are still hot with any part of your body or clothing  
during inspection or repair.  
1. Remove the screws 1, and then pull outward on  
the areas of the cover 2 shown.  
2
1
1
7DK-066  
2. Loosen the bolt 1 and then remove the muffler cap  
2, the muffler screen 3 and spark arrester 4.  
3
2
1
7DK-063  
7DK-064  
4
7DK-065  
27 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Remove the carbon deposits on the muffler screen  
and spark arrester using a wire brush.  
NOTICE  
When cleaning, use the wire brush lightly to avoid  
damaging or scratching of the muffler screen and  
spark arrester.  
711-075  
4. Check the muffler screen and spark arrester.  
Replace them if damaged.  
5. Install the spark arrester.  
TIP  
Align the spark arrester projection 1 with the hole 2 in  
the muffler pipe.  
2
1
7DK-065a  
6. Install the muffler screen and the muffler cap.  
7. Install the cover and tighten the screws.  
7DK-068  
28 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00471  
Fuel tank filter  
1
WARNING  
Never use the gasoline while smoking or in the  
vicinity of an open flame.  
1. Remove the fuel tank cap and filter 1.  
2. Clean the filter with gasoline.  
If damaged, replace it.  
3. Wipe the filter and install it.  
4. Install the fuel tank cap.  
WARNING  
Be sure the fuel tank cap is tightened securely.  
7DK-069  
29 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00601  
STORAGE  
Long term storage of your machine will require some  
preventive procedures to guard against deterioration.  
AE01056  
Drain the fuel  
1. Turn the engine switch to STOP1.  
2. Remove the fuel tank cap. Extract the fuel from the  
fuel tank into an approved gasoline container using  
a commercially available handsiphon. Then, install  
the fuel tank cap.  
1
7DK-044  
WARNING  
Fuel is highly flammable and poisonous. Check  
SAFETY INFORMATION(See page 1) carefully.  
NOTICE  
7DK-025  
Immediately wipe off spilled fuel with a clean, dry,  
soft cloth, since fuel may deteriorate painted sur-  
faces or plastic parts.  
3. Turn the engine switch to ON1.  
1
7DK-039  
7DK-035  
7DK-038  
1
4. Turn the fuel tank cap air vent knob and fuel cock  
knob to ON1.  
5. Start the engine and leave it run until it stops.  
The engine stops in approx. 20 mins. time by run-  
ning out of fuel.  
1
TIP  
9 Do not connect with any electrical devices.  
(unloaded operation)  
9 Duration of the running engine depends on the  
amount of the fuel left in the tank.  
30 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Remove the screws 1, and then remove the cover  
2.  
1
2
7DK-030  
7. Drain the fuel from the carburetor by loosening the  
drain screw 3 on the carburetor float chamber.  
8. Turn the engine switch to OFF.  
3
9. Turn the fuel cock knob to OFF.  
10. Tighten the drain screw 3.  
11. Install the cover and tighten the screws.  
12. Turn the fuel tank cap air vent knob to OFF.  
7DK-071  
13. Tighten further if any screws, bolts and nuts are  
loose.  
14. Store the generator in a dry, well-ventilated place,  
with the cover placed over it.  
31 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Engine  
Perform the following steps to protect the cylinder, pis-  
ton ring, etc. from corrosion.  
1. Remove the spark plug, pour about one table-  
spoon of SAE 10W-30 or 20W-40 motor oil into the  
spark plug hole and reinstall the spark plug. Recoil  
start the engine by turning over several times (with  
ignition off) to coat the cylinder walls with oil.  
2. Pull the recoil starter until you feel compression.  
Then stop pulling. (This prevents the cylinder and  
valves from rusting).  
3. Clean exterior of the generator and apply a rust  
inhibitor.  
4. Store the generator in a dry, well-ventilated place,  
with the cover placed over it.  
5. The generator must remain in a vertical position  
when stored, carried or operated.  
7DK-072  
32 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00512  
TROUBLESHOOTING  
Engine wont start  
1. Fuel systems  
No fuel supplied to combustion chamber.  
2 No fuel in tank .... Supply fuel.  
2 Fuel in tank .... Fuel tank cap air vent knob and fuel  
cock knob to ON1.  
7DK-091  
2 Clogged fuel line .... Clean fuel line.  
2 Clogged carburetor .... Clean carburetor.  
1
7DK-035  
1
7DK-038  
2. Engine oil system  
Insufficient  
2 Oil level is low .... Add engine oil.  
700-006  
33 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Electrical systems  
2 Engine switch to ON1 and pull the recoil starter.  
Poor spark  
2 Spark plug dirty with carbon or wet .... Remove car-  
bon or wipe spark plug dry.  
2 Faulty ignition system .... Consult a Yamaha dealer.  
1
7DK-039  
7DK-041  
791-001d  
AE00515  
Generator wont produce power  
2 Safety device (DC protector) to OFF2 ···· Press  
the DC protector to ON1.  
2 Safety device (AC) to OFF.... Stop the  
engine,then restart.  
1
2
7DK-052  
34 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00515  
A
ENGINE DOES NOT START  
B
Turn the engine switch to ON, then pull  
the recoil starter and check if the oil  
warining light flickers.  
E
F
Check engine oil level.  
C
H
Does not flicker  
D
Flickers.  
Pull the recoil starter and check the  
spark plug for spark strength.  
(See WARNING)  
OK  
Consult a  
Yamaha dealer.  
G
Level low  
Add engine oil.  
w
9 To prevent FIRE HAZARDS be  
sure fuel is not present in the  
spark plug area.  
9 To prevent FIRE HAZARDS be  
sure to place the spark plug as far  
way as possible from the spark  
plug hole and carburetor area.  
9 To prevent ELECTRIC SHOCK do  
not hold spark plug lead with  
hand while testing.  
K
Check the spark plug.  
9 Type: BPR6HS  
9 Gap: 0.60.7 mm (0.0240.028 in)  
L
Incorrect  
Replace or  
Adjust Gap.  
M
OK  
Clean the spark  
plug.  
I
J
OK  
Dose not spark  
N
Q
Check the following  
9 Fuel line clogging  
9 Air cleaner element  
clogging.  
Clean or Replace; Consult  
Yamaha dealer.  
a
O
P
Clogged  
OK  
R
Consult a Yamaha dealer.  
35 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00701  
SPECIFICATIONS  
AE00702  
Dimensions  
Unit  
EF2000iS  
490 (13.3)  
280 (11.0)  
455 (17.9)  
20 (44)  
Overall Length  
Overall Width  
Overall Height  
Dry Weight  
mm (in)  
mm (in)  
mm (in)  
kg (lb)  
AE00704  
Engine  
Unit  
cm3  
EF2000iS  
Type  
Air cooled 4-stroke gasoline OHV  
Cylinder Arrangement  
Displacement  
Inclined, 1 cylinder  
79  
Bore × Stroke  
Operation Hours  
mm (in)  
Hr  
48.6 × 43.0 (1.91 × 1.69)  
4.210.5 (rated load1/4 load)  
Fuel  
Unleaded gasoline  
4.2 (1.11, 0.92)  
0.4 (0.42, 0.35)  
CDI  
Fuel Tank Capacity L (US gal, Imp gal)  
Engine Oil Quantity L (US qt, Imp qt)  
Ignition System  
Spark Plug: Type  
BPR6HS (NGK)  
0.60.7 (0.0240.028)  
61  
Gap  
mm (in)  
dB (A)  
Noise Level*  
* : Measured at rated operation from 7 m (23 ft) distance.  
AE00707  
Generator  
Unit  
EF2000iS  
AC Output  
Rated voltage  
Rated frequency  
Rated current  
Rated output  
V
Hz  
A
120  
60  
13.3  
kVA  
1.6  
Safety Device: Type  
DC Output  
Electronic  
Rated voltage  
Rated current  
Safety Device: Type  
V
A
12  
8
DC protector  
36 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONSUMER INFORMATION  
AE00012  
PRI-I.D. NUMBER:  
Identification number records  
Record your Primary I.D., and serial num-  
bers in the spaces provided, to assist you in  
ordering spare parts from a Yamaha dealer.  
Also record and keep these I.D. numbers in  
a separate place in case your machine is  
stolen.  
MODEL  
PRI-I.D.  
SERIAL No.  
CODE  
AE00011  
Machine identification  
The machine serial number is stamped in  
the location as shown.  
TIP  
The first three digits of these numbers are  
for model identification; the remaining digits  
are the unit production number. Keep a  
record of these numbers for reference  
when ordering parts from a Yamaha dealer.  
Serial NO.  
7DK-  
7DK-24163-00  
7DK-073  
37 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE01119  
YAMAHA MOTOR CORPORATION U.S.A.  
EF- AND EDL-SERIES GENERATOR LIMITED WARRANTY  
Yamaha Motor Corporation, U.S.A. hereby warrants  
that new Yamaha consumer generators purchased  
from an authorized Yamaha consumer generator  
dealer in the continental United States will be free  
from defects in material and workmanship for the  
period of time stated herein, subject to certain stat-  
ed limitations.  
2. Give notice to an authorized Yamaha con-  
sumer generator dealer of any and all apparent  
defects within ten (10) days after discovery,  
and make the unit available at that time for  
inspection and repairs at such dealers place of  
business.  
WARRANTY TRANSFER: To transfer the warranty  
from the original purchaser to any subsequent pur-  
chaser(s), it is imperative that the unit be inspected  
and registered for warranty by an authorized  
Yamaha consumer generator dealer. In order for  
this warranty to remain in effect, this inspection and  
registration must take place within ten (10) days  
after transfer. An inspection and registration fee will  
be charged for this service. In no case will the war-  
ranty be extended beyond the original period.  
THE PERIOD OF WARRANTY Any new EF-series  
or EDL-series Yamaha Generator purchased for  
private, non-commercial use from an authorized  
Yamaha consumer generator dealer in the conti-  
nental United States will  
be warranted against defects in material or work-  
manship for a period two (2) years from date of pur-  
chase, subject to exclusions noted herein. Any  
Yamaha non-commercial  
generator purchased and utilized for commercial or  
rental applications will be warranted for a period  
one (1) year from the date of purchase, subject to  
exclusions noted herein.  
YAMAHA MOTOR CORPORATION, U.S.A. MAKES  
NO OTHER WARRANTY OF ANY KIND,  
EXPRESSED OR IMPLIED. ALL IMPLIED WAR-  
RANTIES OF MERCHANTABILITY AND FITNESS  
FOR A PARTICULAR PURPOSE WHICH EXCEED  
THE OBLIGATIONS AND TIME LIMITS STATED IN  
THIS WARRANTY ARE HEREBY DISCLAIMED BY  
YAMAHA MOTOR CORPORATION, U.S.A. AND  
EXCLUDED FROM THIS WARRANTY.  
DURING THE PERIOD OF WARRANTY any  
authorizedYamaha consumer generator dealer will,  
free of charge, repair or replace, at Yamahas  
option, any part adjudged defective by Yamaha due  
to faulty workmanship or material from the factory.  
Parts used in warranty repairs will be warranted for  
the balance of the products warranty period. All  
parts replaced under warranty become property of  
Yamaha Motor Corporation U.S.A.  
SOME STATES DO NOT ALLOW LIMITATIONS ON  
HOW LONG AN IMPLIED WARRANTY LASTS, SO  
THE ABOVE LIMITATION MAY NOT APPLY TO YOU.  
ALSO EXCLUDED FROM THIS WARRANTY ARE  
ANY INCIDENTAL OR CONSEQUENTIAL DAM-  
AGES INCLUDING LOSS OF USE. SOME STATES  
DO NOT ALLOW THE EXCLUSION OR LIMITATION  
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,  
SO THE ABOVE EXCLUSION MAY NOT APPLY TO  
YOU.  
GENERAL EXCLUSIONS from this warranty shall  
include any failures caused by:  
a. Installation of parts or accessories that are not  
qualitatively equivalent to genuine Yamaha  
parts.  
b. Abnormal strain, neglect, or abuse.  
c. Lack of proper maintenance.  
d. Accident or collision damage.  
THIS WARRANTY GIVES YOU SPECIFIC LEGAL  
RIGHTS, AND YOU MAY ALSO HAVE OTHER  
RIGHTS WHICH VARY FROM STATE TO STATE.  
SPECIFIC EXCLUSIONS from this warranty shall  
include parts replaced due to normal wear or rou-  
tine maintenance.  
YAMAHA MOTOR CORPORATION, U.S.A.  
Post Office Box 6555  
THE CUSTOMERS RESPONSIBILITY under this  
warranty shall be to:  
Cypress, California 90630  
1. Operate and maintain the generator as speci-  
fied in the appropriate Owners Manual;  
38 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARRANTY QUESTIONS AND ANSWERS  
Q. What costs are my responsibility during the  
Q. Is the warranty transferable to second owners?  
A. Yes. The remainder of the existing warranty  
can be transfered upon request.  
warranty period?  
A. The customers responsibility includes all costs  
of normal maintenance service, non-warranty  
repairs, accident damages, as well as oil and  
spark plugs.  
The unit has to be inspected and reregistered  
by an authorized Yamaha generator dealer for  
the policy to remain effective.  
Q. What are some examples of abnormalstrain,  
neglect, or abuse?  
CUSTOMER SERVICE  
A. These terms are general and overlap each  
other in areas. Specific examples include:  
Running the machine out of oil; lack of proper  
maintenance; operating the machine with a  
broken or damaged part which causes anoth-  
er part to fail; and so on. If you have any spe-  
cific questions on operation or maintenance,  
please contact your dealer for advice.  
If your machine requires warranty service, you  
must take it to any authorized Yamaha generator  
dealer within the continental United States. Be sure  
to bring your warranty registration identification or  
other valid proof of the original date of purchase. If  
a question or problem arises regarding warranty,  
first contact the owner of the dealership. Since all  
warranty matters are handled at the dealer level,  
this person is in the best position to help you. If you  
are still not satisfied and require additional assis-  
tance, please write:  
Q. Does the warranty cover incidental costs such  
as transportation due to a failure?  
A. No. The warranty is limited to repair of the  
machine itself.  
YAMAHA MOTOR CORPORATION U.S.A.  
CUSTOMER RELATIONS DEPARTMENT  
P.O. BOX 6555  
Q. May I perform any or all of the recommended  
maintenance shown in the Owners Manual  
instead of having the dealer do them?  
A. Yes, if you are a qualified mechanic and follow  
the procedures specified in the Owners and  
Service Manual. We do recommend, however,  
that items requiring special tools or equipment  
be done by a Yamaha generator dealer.  
Cypress, California 90630  
CHANGE OF ADDRESS  
The federal government requires each manufactur-  
er to maintain a complete, up-to-date list of all first  
purchasers against the possibility of a safety-relat-  
ed defect and recall. This list is compiled from the  
purchase registrations sent to Yamaha Motor  
Corporation, U.S.A. by the selling dealer at the time  
of your purchase. If you should move after you have  
purchased your new generator, please advise us of  
your new address by sending a postcard listing  
your Yamaha model name, engine number, dealer  
number (or dealers name) as it is shown on your  
warranty identification, your name and new mailing  
address. Mail to:  
Q. Will the warranty be void or cancelled if I do not  
operate or maintain my newYamaha exactly as  
specified in the Owners Manual?  
A. No. The warranty on a new Yamaha cannot be  
voidedor cancelled.”  
However, if a particular failure is caused by  
operation or maintenance other than as  
shown in the Owners Manual, that failure  
may not be covered under warranty.  
Q. What responsibility does my dealer have under  
this warranty?  
A. Each Yamaha generator dealer is expected to:  
1. Check the operation of the generator  
before sale.  
YAMAHA MOTOR CORPORATION, U.S.A.  
WARRANTY DEPARTMENT  
P.O. Box 6555  
Cypress, California 90630  
2. Explain the operation, maintenance, and  
warranty requirements to your satisfaction  
at the time of sale, and upon your request  
at any later date.  
This will ensure that Yamaha Motor Corporation,  
U.S.A. has an up-to-date registration record in  
accordance with federal law.  
In addition, each Yamaha generator dealer is  
held responsible for his setup, service and war-  
ranty repair work.  
39 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00789  
EXHAUST EMISSION CONTROL SYSTEM AND COMPONENTS  
Item  
Acronym  
9 CARB. ASSY., LH. & JT., .......................CARB (Carburetor)  
CARBURETOR2  
9 T.C.I. MAGNETO ASSY. & .....................EI (Electronic Ignition)  
PLUG, SPARK  
9 CRANKCASE1 & HEAD, .......................PCV (Positive Crankcase  
CYLINDER1  
Ventilation)  
9 AIR FILTER ASSY. .................................ACL (Air Cleaner)  
9 MUFF., 2, CAP, NET, WIRE2 &  
ARRESTER, SPARK  
The above items and the corresponding acronyms are provided in accordance with U.S.  
EPA REGULATIONS FOR NEW NONROAD SPARK-IGNITION NONHANDHELD  
ENGINES and the CALIFORNIA REGULATIONS FOR 1995 AND LATER SMALL OFF-  
ROAD ENGINES.  
The acronyms conform to the latest version of the SAEs recommended practice docu-  
ment J1930, Diagnostic Acronyms, Terms, and Definitions For Electrical/Electronic  
System.  
It is recommended that these items be serviced by a Yamaha dealer.  
40 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
AE00751  
WIRING DIAGRAM  
L
L
W
B
R
1
6
5
Br  
B
L
O
L
O
2
3
7
4
t
O
Br  
R
O
Br  
Br  
Br  
R
Y
Y
Y
O
O
Br  
R
8
Y
Y
R
R
Y
9
B
R
B
R
0
q
G
Y
R
L
G
G/Y  
Y
R
u
Y
Y
L
O
O
B/W  
B/W  
i
O
O
G/Y  
B
Br  
R/W  
B
B
R/W  
Br  
B
R/W  
Br  
L
R
O
B
O
L
Y
w
e
G/Y  
Br  
R/W  
o
y
Y
Y
L
L
Y
B
p
r
7DK-10  
Color code  
1 Sub coil  
2 DC coil  
3 Main coil  
p Oil level gauge  
B
Black  
Brown  
Green  
Gray  
Br  
G
Gy  
L
4 DC rectifier  
5 DC protector (breaker)  
6 Twin Tech (parallel  
running terminal)  
7 DC receptacle  
8 AC pilot light  
Blue  
O
R
Orange  
Red  
W
Y
White  
Yellow  
9 AC receptacle  
0 Economy control switch  
q Overload indicator light  
w Engine switch  
e Oil warning light  
r Ground (Earth) terminal  
t Control unit  
B/W Black/White  
G/Y Green/Yellow  
R/W Red/White  
y CDI unit/Ignition coil  
u Stepping motor  
i Spark plug  
o CDI magneto  
41 –  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRINTED IN JAPAN  
2009.01-1.0×1 !  
(E)  
PRINTED ON RECYCLED PAPER  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Weed Eater Trimmer 530088833 User Manual
Weed Eater Trimmer 530163531 User Manual
Weslo Treadmill WLTL373080 User Manual
Whirlpool Freezer EV150E User Manual
Whirlpool Range FEP310KV4 User Manual
Wind Crest Cooktop CTG304D User Manual
Wyse Technology Computer Monitor 2510SE User Manual
Xerox All in One Printer 100 EA User Manual
Yamaha Stereo Receiver CRX 332 Black User Manual
Zenoah Brush Cutter BK2650DL User Manual