U
HTR-6140
AV Receiver
OWNER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
10 Ventilation – Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of the
product and to protect it from overheating, and these
openings must not be blocked or covered. The openings
should never be blocked by placing the product on a bed,
sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
11 Power Sources – This product should be operated only from
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product dealer or local power company. For
products intended to operate from battery power, or other
sources, refer to the operating instructions.
12 Grounding or Polarization – This product may be equipped
with a polarized alternating current line plug (a plug having
one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you
are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
13 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against them, paying particular
attention to cords at plugs, convenience receptacles, and the
point where they exit from the product.
14 Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line
surges.
15 Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
16 Overloading – Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result
in a risk of fire or electric shock.
17 Object and Liquid Entry – Never push objects of any kind
into this product through openings as they may touch
dangerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the product.
18 Servicing – Do not attempt to service this product yourself
as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
•
Explanation of Graphical Symbols
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert you to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle
is intended to alert you to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
1
2
3
4
5
6
7
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions
should be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water –
for example, near a bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a swimming pool;
and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall,
causing serious injury to a child or adult, and serious
damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the product. Any mounting of the product should
follow the manufacturer’s instructions, and should use a
mounting accessory recommended by the manufacturer.
A product and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may
cause the product and cart combination to
8
9
overturn.
19 Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
Caution-i En
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
24 Outdoor Antenna Grounding – If an outside antenna or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
e) If the product has been dropped or damaged in any
way, and
f)
When the product exhibits a distinct change in perfor-
mance - this indicates a need for service.
EXAMPLE OF ANTENNA GROUNDING
20 Replacement Parts – When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
ANTENNA
LEAD IN
WIRE
MAST
21 Safety Check – Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
22 Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
23 Heat – The product should be situated away from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and, in particular, specifies
that the cable ground shall be connected to the grounding
system of the building, as close to the point of cable entry as
practical.
NEC – NATIONAL ELECTRICAL CODE
FCC INFORMATION (for US customers)
1
IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”,
please try to eliminate the problem by using one of the
following measures:
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product MUST
be used. Follow all installation instructions. Failure to
follow instructions could void your FCC authorization to
use this product in the USA.
NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance that
your use of this product in a residential environment will
not result in harmful interference with other electronic
devices.
Relocate either this product or the device that is being
affected by the interference.
2
3
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Caution-ii En
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
Caution: Read this before operating your unit.
1
2
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this sound system in a well ventilated, cool, dry, clean
place – away from direct sunlight, heat sources, vibration,
dust, moisture, and/or cold. Allow ventilation space of at least
30 cm on the top, 20 cm on the left and right, and 20 cm on
the back of this unit.
A
18 Before moving this unit, press STANDBY/ON to set this
unit in the standby mode, and disconnect the AC power plug
from the wall outlet.
19 VOLTAGE SELECTOR (Asia and General models only)
The VOLTAGE SELECTOR on the rear panel of this unit
must be set for your local main voltage BEFORE plugging
into the AC wall outlet.
Voltages are 110–120/220–240 V AC, 50/60 Hz.
20 The batteries shall not be exposed to excessive heat such as
sunshine, fire or like.
3
4
Locate this unit away from other electrical appliances, motors,
or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes from
cold to hot, and do not locate this unit in a environment with
high humidity (i.e. a room with a humidifier) to prevent
condensation inside this unit, which may cause an electrical
shock, fire, damage to this unit, and/or personal injury.
Avoid installing this unit where foreign object may fall onto
this unit and/or this unit may be exposed to liquid dripping or
splashing. On the top of this unit, do not place:
21 Excessive sound pressure from earphones and headphones can
cause hearing loss.
WARNING
5
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
–
–
–
other components, as they may cause damage and/or
discoloration on the surface of this unit.
burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
containers with liquid in them, as they may fall and liquid
may cause electrical shock to the user and/or damage to
this unit.
This unit is not disconnected from the AC power
source as long as it is connected to the wall outlet, even
A
if this unit itself is turned off by STANDBY/ON.
This state is called the standby mode. In this state, this
unit is designed to consume a very small quantity of
power.
6
Do not cover this unit with a newspaper, tablecloth, curtain,
etc. in order not to obstruct heat radiation. If the temperature
inside this unit rises, it may cause fire, damage to this unit,
and/or personal injury.
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
7
8
9
Do not plug in this unit to a wall outlet until all connections
are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use force on switches, knobs and/or cords.
10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cord.
POUR LES CONSOMMATEURS CANADIENS
Pour éviter les chocs électriques, introduire la lame la
plus large de la fiche dans la borne correspondante de
la prise et pousser jusqu’au fond.
Cet appareil numérique de la classe B est conforme à
la norme NMB-003 du Canada.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
12 Only voltage specified on this unit must be used. Using this
unit with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury. Yamaha
will not be held responsible for any damage resulting from use
of this unit with a voltage other than specified.
IMPORTANT
Please record the serial number of this unit in the space
below.
MODEL:
13 To prevent damage by lightning, keep the power cord and
outdoor antennas disconnected from a wall outlet or the unit
during a lightning storm.
14 Do not attempt to modify or fix this unit. Contact qualified
Yamaha service personnel when any service is needed. The
cabinet should never be opened for any reasons.
(i.e. vacation), disconnect the AC power plug from the wall
outlet.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
16 Install this unit near the AC outlet and where the AC power
plug can be reached easily.
17 Be sure to read the “Troubleshooting” section on common
operating errors before concluding that this unit is faulty.
Caution-iii En
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic XM Satellite Radio operations....................... 47
SIRIUS Satellite Radio™ tuning .........................51
INTRODUCTION
Quick start guide .................................................... 4
Preparation: Check the items..................................... 4
Step 1: Set up your speakers...................................... 5
Step 2: Connect your DVD player and other
components............................................................ 6
channels............................................................... 54
Using iPod™ ..........................................................57
Controlling iPod™................................................... 57
Pairing the Bluetooth™ adapter and your Bluetooth
component ........................................................... 59
Connecting speakers................................................ 11
1 SOUND MENU.................................................... 63
2 INPUT MENU...................................................... 68
3 OPTION MENU................................................... 70
Remote control features........................................73
Controlling this unit, a TV, or other components.... 73
Bluetooth™ adapter............................................. 19
Connecting the power cable..................................... 20
Setting the speaker impedance................................. 21
Turning on and off the power.................................. 21
Front panel display .................................................. 22
Optimizing the speaker setting
ADDITIONAL INFORMATION
Troubleshooting.....................................................78
Glossary..................................................................88
Specifications .........................................................90
Creating your original SCENE templates................ 31
Selecting audio input jacks
(at the end of this manual)
FM/AM tuning...................................................... 43
Automatic tuning ..................................................... 43
Manual tuning.......................................................... 43
Automatic preset tuning........................................... 44
Manual preset tuning ............................................... 44
Selecting preset stations........................................... 45
Exchanging preset station........................................ 45
Front panel................................................................i
Remote control ....................................................... ii
List of remote control codes ................................. iii
About this manual
• Some operations can be performed by using either the buttons on the
front panel or the ones on the remote control. In case the button
names differ between the front panel and the remote control, the
button name on the remote control is given in parentheses.
are subject to change in part as a result of improvements, etc. In case
of differences between the manual and product, the product has
priority.
J
• “ SPEAKERS” or “4DVD” (example) indicates the name of the
parts on the front panel or the remote control. Refer to the attached
sheet or the pages at the end of this manual for the information about
each position of the parts.
• The symbol “☞” with page number(s) indicates the corresponding
reference page(s).
1 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Features
Built-in 5-channel power amplifier
Radio tuners
◆ Minimum RMS output power
◆ FM/AM tuning capability
◆ XM Satellite Radio tuning capability (using XM Mini-Tuner
and Home Dock, sold separately)
◆ SIRIUS Satellite Radio™ tuning capability (using SIRIUS
[U.S.A. and Canada models]
(1 kHz, 0.9% THD, 8 Ω)
105 W/ch
Connect tuner, sold separately)
[Other models]
(1 kHz, 0.9% THD, 6 Ω)
105 W/ch
HDMI (High-Definition Multimedia Interface)
◆ HDMI interface for standard, enhanced or high-definition
video (includes 1080p video signal transmission) as well as
multi-channel digital audio
SCENE select function
◆ Preset SCENE templates for various situations
◆ SCENE template customizing capability
DOCK terminal
◆ DOCK terminal to connect a Yamaha iPod universal dock
(such as YDS-10, sold separately) or Bluetooth adapter
(such as YBA-10, sold separately).
Decoders and DSP circuits
◆ Proprietary Yamaha technology for the creation of multi-
Other features
channel surround sound
◆ YPAO (Yamaha Parametric Room Acoustic Optimizer) for
automatic speaker setup
◆ 192-kHz/24-bit D/A converter
◆ Compressed Music Enhancer mode
◆ Dolby Digital decoder
◆ Dolby Pro Logic/Dolby Pro Logic II decoder
◆ DTS decoder
◆ Neural Surround decoder
(U.S.A. and Canada models only)
◆ Virtual CINEMA DSP
◆ DIRECT mode for high quality sound for all sources
◆ 6 additional input jacks for discrete multi-channel input
◆ OSD (on-screen display) menus that allow you to optimize
this unit to suit your individual audiovisual system
◆ Component video input/output capability
(3 COMPONENT VIDEO INs and 1 MONITOR OUT)
◆ Optical and coaxial digital audio signal jacks
◆ Sleep timer
◆ SILENT CINEMA™
◆ Cinema and music night listening modes
◆ iPod controlling capability
◆ Remote control with preset remote control codes
“DTS” and “DTS Digital Surround” are registered trademarks of
DTS, Inc.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, and the double-D symbol are trademarks
of Dolby Laboratories.
The XM name and related logos are registered trademarks of XM
Satellite Radio Inc.
“SILENT CINEMA” is a trademark of YAMAHA
CORPORATION.
iPod™
Neural Surround™ name and related logos are trademarks owned
by Neural Audio Corporation.
“iPod” is a trademark of Apple, Inc., registered in the U.S. and
other countries.
Bluetooth™
Bluetooth is a registered trademark of the Bluetooth SIG and is
used by Yamaha in accordance with a license agreement.
©2006 SIRIUS Satellite Radio Inc. “SIRIUS”, “Sirius Connect”,
the SIRIUS dog logo, channel names and logos are trademarks of
SIRIUS Satellite Radio Inc.
“HDMI”, the “HDMI” logo and “High-Definition Multimedia
Interface” are trademarks or registered trademarks of HDMI
Licensing LLC.
2 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Getting started
■ Supplied accessories
Check that you received all of the following parts.
■ Installing batteries in the remote control
3
1
❏ Remote control
❏ Batteries (2) (AAA, R03, UM-4)
❏ Optimizer microphone
❏ AM loop antenna
❏ Indoor FM antenna
■ VOLTAGE SELECTOR
2
(Asia and General models only)
Caution
The VOLTAGE SELECTOR on the rear panel of this
unit must be set for your local voltage BEFORE
plugging the power cable into the AC wall outlet.
Improper setting of the VOLTAGE SELECTOR may
cause damage to this unit and create a potential fire
hazard.
1
2
Take off the battery compartment cover.
Insert the two supplied batteries
(AAA, R03, UM-4) according to the polarity
markings (+ and –) on the inside of the
battery compartment.
Rotate the VOLTAGE SELECTOR clockwise or
counterclockwise to the correct position using a
straight slot screwdriver.
Voltages are as follows:
Asia model ................... 220/230–240 V AC, 50/60 Hz
General model
...................... 110/120/220/230–240 V AC, 50/60 Hz
3
Snap the battery compartment cover back
into place.
VOLTAGE
SELECTOR
Notes
• Change all of the batteries if you notice that the operation range
of the remote control decreases.
230-
Voltage indication
240V
• Do not use an old battery and a new one together.
• Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
• If the batteries have leaked, dispose of them immediately. Avoid
touching the leaked material or letting it come into contact with
clothing, etc. Clean the battery compartment thoroughly before
installing new batteries.
• Do not throw away batteries with general house waste; dispose
of them correctly in accordance with your local regulations.
• If the remote control is without batteries for more than 2
minutes, or if exhausted batteries remain in the remote control,
the contents of the memory may be cleared. When the memory
is cleared, insert new batteries and set up the remote control
code.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer
Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound
come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your
sensitive hearing.
Since hearing damage from loud sounds is often
undetectable until it is too late, Yamaha and the
Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid
prolonged exposure from excessive volume levels.
3 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start guide
Quick start guide
The following steps describe the easiest way to enjoy
DVD movie playback in your home theater.
Preparation: Check the items
Prepare the following items.
❏ Speakers
Front right
speaker
Video monitor
Subwoofer
❏ Front speaker .....................................x 2
❏ Center speaker ...................................x 1
❏ Surround speaker ..............................x 2
Select magnetically shielded speakers. The
minimum required speakers are two front speakers.
The priority of the requirement of other speakers is
as follows:
Front left
speaker
Surround right
speaker
Center speaker
1. Two surround speakers
2. Center speaker
DVD player
❏ Active subwoofer ...................................x 1
Select an active subwoofer equipped with an RCA
input jack.
Surround left
speaker
❏ Speaker cable .........................................x 5
❏ Subwoofer cable .....................................x 1
Select a monaural RCA cable.
Step 1: Set up your speakers
❏ DVD player ..............................................x 1
Select DVD player equipped with coaxial digital
audio output jack and composite video output
jack.
❏ Video monitor..........................................x 1
Select a TV monitor, video monitor or projector
equipped with a composite video input jack.
❏ Video cable .............................................x 2
Select an RCA composite video cable.
Step 2: Connect your DVD player
and other components
❏ Digital coaxial audio cable ....................x 1
Step 3: Press SCENE 1 button
☞ P. 7
Enjoy DVD playback!
4 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start guide
Be sure to connect the left channel (L), right channel
(R), “+” (red) and “–” (black) properly.
Step 1: Set up your speakers
Front and center speakers
Place your speakers in the room and connect them to this
unit.
COAXIAL
OPTICAL
DVD
1
DTV/CBL
2
CD
3
DVD IN1
DTV/CBL IN2
OUT
HDMI
DIGITAL INPUT
XM
SIRIUS
DTV/CBL
DOCK
COMPONENT VIDEO
ANTENNA
DVD
P
R
P
B
Y
P
R
P
B
Y
A
B
C
AM
DVR
U
R
R
O
U
N
D
L
GND
MONITOR OUT
VIDEO
FM
VIDEO
U7NB5AL.
MONITOR
OUT
IN
OUT
DVR
DVD
DTV/CBL
L
L
CENTER
SUB
SUB
F
R
R
W
O
O
ER
C
E
N
T
E
R
R
F
R
O
N
T
A
F
R
O
N
T
B
L
IN
MD/ OUT
IN
OUT
FRONT
SURROUND WOOFER
(PLAY) CD-R (REC)
DVD
DTV/CBL
DVR
CD
AUDIO
MULTI CH INPUT
OUTPUT
1
2
Place your speakers and subwoofer in the
room.
Connect speaker cables to each speaker.
To the center
speaker
To the front
right speaker
To the front
left speaker
Surround speakers
Cables are colored or shaped differently, perhaps with
a stripe, groove or ridge. Connect the striped
(grooved, etc.) cable to the “+” (red) terminals of
your speaker. Connect the plain cable to the “–”
(black) terminals.
3
Connect each speaker cable to the
corresponding speaker terminal of this unit.
1
2
3
4
To the surround To the surround
right speaker
left speaker
1 Make sure that this unit and the subwoofer are
unplugged from the AC wall outlets.
2 Twist the exposed wires of the speaker cables
together to prevent short circuits.
4
Connect the subwoofer cable to the input
jack of the subwoofer and the SUBWOOFER
OUTPUT jack of this unit.
3 Do not let the bare speaker wires touch each other.
4 Do not let the bare speaker wires touch any metal
part of this unit.
Subwoofer
AV receiver
SUBWOOFER
OUTPUT jack
Input jack
Subwoofer cable
5 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start guide
Step 2: Connect your DVD player
and other components
3
Connect the video cable to the video input
jack of your video monitor and the VIDEO
MONITOR OUT jack of this unit.
SPEAKERS
COAXIAL
O
P
T
I
C
AL
AV receiver
Video monitor
1
D
V
D
D
T
2
V
/
C
B
L
CD
3
DVD IN1
DTV/CBL IN2
OUT
HDMI
D
I
G
I
T
A
L
I
N
P
U
T
XM
SIRIUS
DTV/CBL
DOCK
COMPONENT VIDEO
ANTENNA
DVD
A
P
R
P
B
Y
P
R
P
B
Y
B
AM
DVR
R
SURROUND
L
C
GND
MONITOR OUT
V
V
IDID
E
EO
O
FM
VIDEO
U7NB5AL.
MONITOR
I
N
OUT
D
V
D
D
T
V
/
C
B
L
DVR
OUT
L
L
CENTER
SUB
SUB
WOOFER
R
R
CENTER
R
FRONT
A
L
R
FRONT
B
L
IN
MD/ OUT
IN
OUT
FRONT
SURROUND WOOFER
(PLAY) CD-R (REC)
DVD
DTV/CBL
DVR
CD
AUDIO
MULTI CH INPUT
OUTPUT
Make sure that this unit and the DVD
player are unplugged from the AC wall
outlets.
Video input
jack
Video cable
VIDEO MONITOR OUT
jack
4
Connect the power plug of this unit and other
components into the AC wall outlet.
1
Connect the digital coaxial audio cable to the
digital coaxial audio output jack of your DVD
player and the DVD DIGITAL INPUT COAXIAL
jack of this unit.
■ For further connections
•
Using the other kind of speaker
combinations
☞ P. 11
☞ P. 15
☞ P. 16
☞ P. 17
☞ P. 17
DVD player
AV receiver
•
•
•
•
•
Connecting a video components
Connecting a DVD player
Connecting a DVD recorder
Connecting a set-top boxes
Connecting a CD player
and a CD recorder/ MD recorder
☞ P. 18
☞ P. 18
•
•
•
Connecting a multi-format player
or an external decoder
Digital coaxial
audio output jack
Connecting an Yamaha iPod/Bluetooth
dock
☞ P. 19
Using the VIDEO AUX jacks on the front
panel
☞ P. 19
Digital coaxial audio
cable
•
•
Connecting an FM/AM antenna
☞ P. 20
DVD DIGITAL INPUT
COAXIAL jack
Connecting the XM Mini-Tuner Dock
☞ P. 46
2
Connect the video cable to the composite
video output jack of your DVD player and the
DVD VIDEO jack of this unit.
•
Connecting the SIRIUS Connect tuner
☞ P. 51
DVD player
AV receiver
Composite video
output jack
Video cable
DVD VIDEO jack
6 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start guide
■ About SCENE function
Just by pressing one SCENE button, you can turn on this
unit and recall your favorite input source and sound field
program according to the SCENE template that has been
assigned to the SCENE button. The SCENE templates are
built combinations of input sources and sound field
programs.
Check the type of the connected speakers.
If the speakers are 6 ohm speakers, set “SP IMP.” to
“6Ω MIN” before using this unit (see page 21).
y
If you connect a Yamaha product that has capability of the
SCENE control signals, this unit can automatically activate the
component and start playback. Refer to the instruction manual of
the DVD player for further information.
1
Turn on the video monitor and then set the
input source selector of the video monitor to
this unit.
■ The default assigned SCENE templates
Q
2
Press SCENE 1.
This unit is turned on. “DVD Viewing” appears in the
front panel display, and this unit automatically
optimize own status for the DVD playback.
Default
SCENE
button
The name of the SCENE template
and its description
SCENE
1
DVD Viewing
– input source: DVD
– sound field program: STRAIGHT
For when you want to enjoy a DVD playback.
SCENE
2
Disc Listening
– input source: DVD
– sound field program: 5ch Stereo
For when you want to listen to a music disc from
the connected DVD player as the background
music for this room.
TV Viewing *1
– input source: DTV/CBL
SCENE
3
– sound field program: STRAIGHT
For when you want to watch a TV program.
Radio Listening *2, *3, *4
– input source: TUNER
SCENE
4
y
The indicator on the selected SCENE button lights up while
this unit is in the SCENE mode.
– sound field program: 5ch Enhancer
For when you want to listen to a music program
3
4
Start playback of the desired DVD on your
player.
Note
I
Rotate
VOLUME to adjust the volume.
*1 You must connect a cable TV or a satellite tuner to this unit in
advance. See page 17 for details.
*2 You need to connect the supplied FM and AM antennas to this
unit in advance. See page 20 for details.
*3 You must tune into the desired radio station in advance. See
pages 43 to 45 for tuning information.
AM loop antenna, or adjust the position of the end of the
indoor FM antenna.
y
You can change the assigned SCENE template for the SCENE
buttons. See page 28 for details.
Note
When you change the input source or sound field program, the
SCENE mode is deactivated.
7 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick start guide
■ After using this unit...
What do you want to do with this
unit?
A
Press STANDBY/ON on the front panel to set
this unit to the standby mode.
■ Customizing the SCENE templates
•
•
Using various SCENE templates
☞ P. 28
Creating your original SCENE templates
☞ P. 31
■ Using various input sources
•
•
•
Basic controls of this unit
☞ P. 33
☞ P. 43
Enjoying FM/AM radio programs
Enjoying XM Satellite Radio programs
☞ P. 46
•
Enjoying SIRIUS Satellite Radio programs
☞ P. 51
This unit is set to the standby mode. In the standby mode,
this unit consumes a small amount of power in order to
receive infrared signals from the remote control. To turn
•
•
Using your iPod with this unit.
☞ P. 57
☞ P. 59
Using your Bluetooth components
with this unit.
A
on this unit from the standby mode, press STANDBY/
ON (or HPOWER). See page 21 for details.
■ Using various sound features
•
•
•
Using various sound field programs
☞ P. 38
Using the direct mode for the high
quality sound
☞ P. 41
Customizing the sound field programs
☞ P. 40
■ Adjusting the parameters of this unit
•
Automatically optimizing the speaker
parameters for your listening room
(AUTO SETUP)
☞ P. 24
•
Manually adjusting various parameters of
this unit
☞ P. 61
•
•
Setting the remote control
☞ P. 73
Adjusting the advanced parameters☞ P. 76
■ Additional features
Automatically turning off this unit
☞ P. 37
8 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connections
Rear panel
1
2
3 4 5 6
7
8
SPEAKERS
COAXIAL
OPTICAL
DVD
DTV/CBL
CD
DVD IN1
DTV/CBL IN2
OUT
1
2
3
HDMI
DIGITAL INPUT
XM
SIRIUS
DTV/CBL
DOCK
COMPONENT VIDEO
ANTENNA
DVD
A
P
R
P
B
Y
P
R
P
B
Y
B
AM
DVR
R
SURROUND
L
C
GND
MONITOR OUT
VIDEO
FM
U7NB5AL.
MONITOR
OUT
IN
OUT
DVR
DVD
DTV/CBL
L
L
CENTER
SUB
SUB
WOOFER
R
R
CENTER
R
FRONT
A
L
R
FRONT
B
L
IN
MD/ OUT
IN
OUT
DVR
FRONT
SURROUND WOOFER
(PLAY) CD-R (REC)
DVD
DTV/CBL
CD
AUDIO
MULTI CH INPUT
OUTPUT
9
0
A
B C
(U.S.A. model)
Name
Page
1
2
3
4
5
HDMI jacks
DIGITAL INPUT jacks
COMPONENT VIDEO jacks
14
13
13
46
51
XM jack (U.S.A. and Canada models only)
SIRIUS jack
(U.S.A. and Canada models only)
6
7
8
DOCK terminal
19
11
3
Speaker terminals
VOLTAGE SELECTOR
(Asia and General models only)
9
0
A
B
C
AUDIO jacks
13
13
18
11
20
VIDEO jacks
MULTI CH INPUT jacks
SUBWOOFER OUTPUT jack
ANTENNA terminals
9 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Placing speakers
The speaker layout below shows the speaker setting we recommend. You can use it to enjoy CINEMA DSP and multi-
channel audio sources.
FL
FR
C
FR
SW
FL
30˚
C
SR
SL
SL
SR
SR
60˚
80˚
SL
Front left and right speakers (FL and FR)
The front speakers are used for the main source sound plus effect sounds. Place these speakers at an equal distance from the
ideal listening position. The distance of each speaker from each side of the video monitor should be the same.
Center speaker (C)
The center speaker is for the center channel sounds (dialog, vocals, etc.). If for some reason it is not practical to use a
center speaker, you can do without it. Best results, however, are obtained with the full system.
Surround left and right speakers (SL and SR)
The surround speakers are used for effect and surround sounds.
Subwoofer (SW)
The use of a subwoofer with a built-in amplifier, such as the Yamaha Active Servo Processing Subwoofer System, is
effective not only for reinforcing bass frequencies from any or all channels, but also for high fidelity sound reproduction
of the LFE (low-frequency effect) channel included in Dolby Digital and DTS sources. The position of the subwoofer is
not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front
speakers. Turn it slightly toward the center of the room to reduce wall reflections.
10 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting speakers
Be sure to connect the left channel (L), right channel (R), “+” (red) and “–” (black) properly. If the connections are faulty,
this unit cannot reproduce the input sources accurately.
Caution
•
•
Before connecting the speakers, make sure that the AC power plug is disconnected from the AC wall outlet.
Do not let the bare speaker wires touch each other or let them touch any metal part of this unit. This could damage
this unit and/or the speakers. If the speaker wires are short-circuited, “CHECK SP WIRES” appears in the front
panel display when you turn on this unit.
•
•
Use the magnetically shielded speakers. If this type of speaker still creates interference with the monitor, place the
speakers away from the monitor.
If you are to use 6 ohm speakers, be sure to set “SP IMP.” to “6Ω MIN” before using this unit. For details about the
speaker impedance setting, see page 21.
Surround speakers
Right
Left
SPEAKERS
COAXIAL
OPTICAL
DVD
DTV/CBL
CD
DVD IN1
DTV/CBL IN2
OUT
1
2
3
HDMI
DIGITAL INPUT
XM
SIRIUS
DTV/CBL
DOCK
COMPONENT VIDEO
ANTENNA
DVD
A
P
R
P
B
Y
P
R
P
B
Y
B
AM
DVR
R
SURROUND
L
C
GND
MONITOR OUT
VIDEO
FM
VIDEO
U7NB5AL.
MONITOR
OUT
IN
OUT
DVR
DVD
DTV/CBL
L
L
CENTER
SUB
SUB
WOOFER
R
R
CENTER
R
FRONT
A
L
R
FRONT
B
L
IN
MD/ OUT
IN
OUT
DVR
FRONT
SURROUND WOOFER
(PLAY) CD-R (REC)
DVD
DTV/CBL
CD
AUDIO
MULTI CH INPUT
OUTPUT
FRONT B terminals
Connect the alternative front speaker system
(FRONT B).
Center
speaker
Subwoofer
Right
Left
Front speakers
(FRONT A)
11 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
■ Before connecting to the SPEAKERS
terminal
A speaker cord is actually a pair of insulated cables
running side by side. Cables are colored or shaped
differently, perhaps with a stripe, groove or ridges.
Connect the striped (grooved, etc.) cable to the “+” (red)
terminals of this unit and your speaker. Connect the plain
cable to the “–” (black) terminals.
Remove approximately 10 mm (3/8”) of insulation
from the end of each speaker cable and then
twist the bare wires of the cable together to
prevent short circuits.
10 mm (3/8”)
■ Connecting to the SPEAKER terminals
2
Red: positive (+)
Black: negative (–)
1
3
1
2
Loosen the knob.
Insert the bare end of the speaker wire into
the hole on the terminal.
3
Tighten the knob to secure the wire.
Connecting the banana plug
(except Europe, Russia, Korea, and Asia models)
The banana plug is a single-pole electrical connector
widely used to terminate speaker cables. First, tighten the
knob and then insert the banana plug connector into the
end of the corresponding terminal.
Banana plug
12 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Information on jacks and cable plugs
Connect one of the type of the audio jack(s) and/or video jack(s) that your input components are equipped with.
Audio jacks and cable plugs Video jacks and cable plugs
COMPONENT VIDEO
DIGITAL AUDIO
COAXIAL
DIGITAL AUDIO
OPTICAL
AUDIO
VIDEO
P
R
P
B
Y
L
R
(Yellow)
(White)
(Red)
(Orange)
(Red)
(Blue) (Green)
V
O
PB
Y
PR
L
R
C
Composite
video cable
plug
Left and right
analog audio
cable plugs
Coaxial
digital audio
cable plug
Optical
digital
audio cable
plug
Component
video cable
plugs
■ Audio jacks
■ Video jacks
This unit has three types of audio jacks. Connection
depends on the availability of audio jacks on your other
components.
This unit has two types of video jacks. Connection
depends on the availability of input jacks on your video
monitor.
AUDIO jacks
VIDEO jacks
For conventional analog audio signals transmitted via left
and right analog audio cables. Connect red plugs to the
right jacks and white plugs to the left jacks.
For conventional composite video signals transmitted via
composite video cables.
COMPONENT VIDEO jacks
DIGITAL AUDIO COAXIAL jacks
For digital audio signals transmitted via coaxial digital
audio cables.
For component signals, separated into the luminance (Y)
and chrominance (PB, PR) video signals transmitted on
separate wires of component video cables.
DIGITAL AUDIO OPTICAL jacks
For digital audio signals transmitted via optical digital
audio cables.
Video signal flow for MONITOR OUT
Output
Input
(MONITOR OUT)
PR PB
Y
PR PB
Y
COMPONENT
VIDEO
Notes
• You can use the digital jacks to input PCM, Dolby Digital and
DTS bitstreams. Optical input jacks are compatible with digital
signals with up to 96 kHz of sampling frequency.
VIDEO
• This unit handles digital and analog signals independently. Thus
audio signals input at the digital jacks are not output at the
analog AUDIO OUT (REC) jacks.
Note
The OSD signal is not output at the DVR OUT (REC) jacks.
13 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Information on HDMI™
■ HDMI compatibility with this unit
■ HDMI jack and cable plug
Compatible
HDMI
components
HDMI
Audio signal
types
Audio signal
formats
2ch Linear PCM
2ch, 32-192 kHz,
16/20/24 bit
CD, DVD-Video,
DVD-Audio, etc.
Multi-ch Linear
PCM
6ch, 32-192 kHz,
16/20/24 bit
DVD-Audio, etc.
Bitstream
Dolby Digital, DTS DVD-Video, etc.
HDMI cable plug
y
This unit’s HDMI interface is based on the following
standards:
• We recommend using an HDMI cable shorter than 5 meters (16
feet) with the HDMI logo printed on it.
• Use a conversion cable (HDMI jack ↔ DVI-D jack) to connect
this unit to other DVI components.
•
HDMI Version 1.2a (High-Definition Multimedia
Interface Specification Version 1.2a) licensed by
HDMI Licensing, LLC.
•
HDCP (High-bandwidth Digital Content Protection
System) licensed by Digital Content Protection,
LLC.
Notes
• Do not disconnect or connect the cable or turn off the power of
the HDMI components connected to the HDMI OUT jack of
this unit while data is being transferred. Doing so may disrupt
playback or cause noise.
• Audio signals input at input jacks other than the HDMI IN DVD
or HDMI IN DTV/CBL jack of this unit cannot be digitally
output at the HDMI OUT jack.
• If you turn off the power of the video monitor connected to the
HDMI OUT jack via a DVI connection, this unit may fail to
establish the connection to the component.
Notes
• When CPPM copy-protected DVD audio is played back, video
and audio signals may not be output depending on the type of
the DVD player.
• This unit is not compatible with HDCP-incompatible HDMI or
DVI components.
• You can check the potential problem about the HDMI
connection (see page 36).
Audio and video signal flow
■ Audio signal flow
■ Video signal flow
Input
Output
Input
Output
HDMI
HDMI
AUDIO
COMPONENT
VIDEO
Digital output
Analog output
VIDEO
Through
Notes
• 2-channel as well as multi-channel PCM, Dolby Digital and
DTS signals input at the HDMI IN DVD or HDMI IN DTV/
CBL jack can be output at the HDMI OUT jack only when
“SUPPORT AUDIO” is set to “Other” (see page 67).
• Audio signals input at the HDMI IN jacks are not output at the
AUDIO output jacks.
14 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting video components
Connect your TV (or projector) to the HDMI OUT jack,
the COMPONENT VIDEO MONITOR OUT jacks, or the
VIDEO MONITOR OUT jack of this unit.
Notes
• Some video monitors connected to this unit via a DVI
connection fail to recognize the HDMI audio/video signals
being input if they are in the standby mode. In this case, the
HDMI indicator flashes irregularly.
• When you connect your TV monitor or projector via HDMI
connection, the OSD does not appear. In such cases, connect the
TV monitor or projector via component, or video connection.
• Connect the input source components to the HDMI IN DVD or
HDMI IN DTV/CBL jack to display the video images on the
video monitor connected to the HDMI OUT jack.
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
y
You can choose to play back HDMI audio signals on this unit or
on another HDMI component connected to the HDMI OUT jack
of this unit. Use the “SUPPORT AUDIO” parameter in “SOUND
MENU” to select the component to play back HDMI audio
signals (see page 67).
COAXIAL
OPTICAL
DVD
DTV/CBL
CD
VD IN1
DTV/CBL IN2
OUT
1
DVD
A
2
3
HDMI
DIGITAL INPUT
XM
SIRIUS
DTV/CBL
COMPONENT VIDEO
P
R
P
B
Y
P
R
P
B
Y
B
DVR
C
MONITOR OUT
VIDEO
MONITOR
OUT
IN
OUT
DVR
DVD
DTV/CBL
L
CENTER
SUB
R
WO
D/ OUT
-R (REC)
IN
OUT
FRONT
SURROUND WOOFER
DVD
DTV/CBL
DVR
CD
AUDIO
MULTI CH INPUT
OUTPUT
PR
PB
Y
Component
video in
HDMI in
V
Video in
TV (or projector)
indicates recommended connections
indicates alternative connections
15 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting other components
Notes
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
• Be sure to make the same type of video connections as those
made for your TV (see page 15).
• To make a digital connection to a component other than the
default component assigned to DIGITAL INPUT jack, select
the corresponding setting for “OPTICAL IN” or “COAXIAL
IN” in “INPUT ASSIGNMENT” (see page 68).
■ Connecting a DVD player
DVD player
HDMI out
PR
PB
Y
R
L
V
C
COAXIAL
DVD
OPTICAL
DTV/CBL
CD
DTV/CBL IN2
OUT
1
DVD
A
2
3
DVD IN1
XM
SIRIUS
DTV/CBL
HDMI
DIGITAL INPUT
COMPONENT VIDEO
P
R
P
B
Y
P
R
P
B
Y
B
DVR
C
MONITOR OUT
VIDEO
VIDEO
MONITOR
OUT
IN
OUT
DVR
DTV/CBL
DVD
L
L
L
CENTER
R
R
WO
SUB
SURROUND WOOFER
IN
MD/ OUT
IN
OUT
FRONT
MULTI CH INPUT
(PLAY) CD-R (REC)
DTV/CBL
DVD
AUDIO
DVR
CD
OUTPUT
indicates recommended connections
indicates alternative connections
(One for the video connection,
and one for the audio connection)
16 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
■ Connecting a DVD recorder, PVR or VCR
DVD
DTV/CBL
CD
DVD IN1
DTV/CBL IN2
OUT
1
2
3
HDMI
DIGITAL INPUT
XM
SIRIUS
DTV/CBL
COMPONENT VIDEO
DVD
P
R
P
B
Y
P
R
P
B
Y
A
B
DVR
C
MONITOR OUT
VIDEO
VIDEO
MONITOR
OUT
IN
OUT
DVR
DVD
DTV/CBL
L
L
CENTER
SUB
R
R
WO
IN
MD/ OUT
IN
OUT
FRONT
SURROUND WOOFER
(PLAY) CD-R (REC)
DVD
DTV/CBL
DVR
CD
AUDIO
MULTI CH INPUT
OUTPUT
V
PR
PB
Y
V
R
L
R
L
Component video out
Video out
DVD recorder,
PVR or VCR
■ Connecting a set-top box
Satellite receiver, cable TV
receiver or HDTV decoder
HDMI out
Component video out
L
R
V
O
PR
PB
Y
COAXIAL
OPTICAL
DVD
CD
DTV/CBL
DVD IN1
DTV/CBL IN2
OUT
1
2
3
HDMI
DIGITAL INPUT
XM
SIRIUS
DTV/CBL
COMPONENT VIDEO
DVD
A
P
R
P
B
Y
P
R
P
B
Y
B
DVR
C
MONITOR OUT
VIDEO
VIDEO
MONITOR
OUT
IN
OUT
DVR
indicates recommended
DVD
DTV/CBL
connections
L
L
CENTER
SUB
R
R
indicates alternative
connections
(One for the video connection,
and one for the audio
connection)
WO
IN
MD/ OUT
IN
OUT
FRONT
SURROUND WOOFER
(PLAY) CD-R (REC)
DVD
DTV/CBL
DVR
CD
AUDIO
MULTI CH INPUT
OUTPUT
17 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting audio components
Connect the audio components as follows.
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
■ Connecting a CD player and a CD
recorder/MD recorder
Notes
• When you connect your CD player via analog and digital
connection, priority is given to the signal input at the DIGITAL
INPUT jack.
• To make a digital connection to a component other than the
default component assigned to each DIGITAL INPUT jack,
select the corresponding setting in “INPUT ASSIGNMENT”
(see page 68).
indicates recommended connections
indicates alternative connections
COAXIAL
OPTICAL
DVD
DTV/CBL
CD
DVD IN1
DTV/CBL IN2
OUT
1
2
3
HDMI
DIGITAL INPUT
COMPONENT VIDEO
DVD
A
P
R
P
B
Y
PR
O
MONITOR OUT
VIDEO
VIDEO
L
R
Optical out
Audio in
MONITOR
OUT
IN
OUT
DVR
DVD
DTV/CBL
LL
L
L
L
R
R
R
R
Audio out
Audio out
IN
MD/ OUT
IN
OUT
CD recorder or
MD recorder
CD player
FRONT
SURROUND
W
(PLAY) CD-R (REC)
DVD
DTV/CBL
DVR
CD
AUDIO
MULTI CH INPU
■ Connecting a multi-format player or an external decoder
This unit is equipped with 6 additional input jacks (FRONT L/R, SURROUND L/R, CENTER and SUBWOOFER) for
discrete multi-channel input from a multi-format player, external decoder or sound processor. Connect the output jacks
on your multi-format player or external decoder to the MULTI CH INPUT jacks. Be sure to match the left and right
output jacks to the left and right input jacks for the front and surround channels.
Notes
• When you select the component connected to the MULTI CH INPUT jacks as the input source (see page 34), this unit automatically
turns off the digital sound field processor, and you cannot select sound field programs.
• This unit does not redirect signals input at the MULTI CH INPUT jacks to accommodate for missing speakers. We recommend that
you connect a 5.1-channel speaker system before using this feature.
CENTER
L
R
SUB
FRONT
SURROUND
WOOFER
MULTI CH INPUT
L
R
L
R
Multi-format player/
External decoder
18 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting a Yamaha iPod
™
Using the VIDEO AUX jacks on the
front panel
Use the VIDEO AUX jacks on the front panel to connect a
game console or a video camera to this unit.
universal dock or Bluetooth
™
adapter
Caution
Make sure that this unit and other
components are unplugged from the
AC wall outlets.
Be sure to turn down the volume of this unit and other
components before making connections.
Notes
This unit is equipped with the DOCK terminal on the rear
panel that allows you to connect a Yamaha iPod universal
dock (such as YDS-10, sold separately) or Bluetooth
adapter (such as YBA-10, sold separately). Connect a
Yamaha iPod universal dock or Bluetooth adapter to the
DOCK terminal on the rear panel of this unit using its
dedicated cable.
• To reproduce the source signals input at these jacks, select
“V-AUX” as the input source.
• When audio signals are input at the AUDIO jacks, PORTABLE
jack and the DOCK terminal on the rear panel, the priority order
of the input signal is as follows:
1. DOCK
2. PORTABLE
3. AUDIO
VOLUME
STANDBY/
ON
OPTIMIZER MIC
EDIT
SEARCH MODE
PRESET/TUNING
CATEGORY
A/B/C/D/E
INFO
BAND
l
PRESET/TUNING/CH
h
MEMORY
TUNING AUTO/MAN'L
SCENE
XM
SIRIUS
DTV/CBL
DOCK
1
2
3
4
ANTENNA
VIDEO AUX
AUDIO
l
PROGRAM
h
l
INPUT
h
VIDEO
L
R
PORTABLE
P
B
Y
PHONES
SPEAKERS
A/B/OFF
TONE CONTROL
STRAIGHT
DIRECT
AUDIO SELECT
B
SILENT CINEMA
EFFECT
AM
DVR
C
GND
3.5 mm stereo
mini plug
VIDEO AUX
AUDIO
VIDEO
L
R
PORTABLE
Yamaha iPod universal dock
or Bluetooth adapter
V
L
R
Video
output
Audio
output
Audio
output
Game console or
video camera
Portable audio
player
19 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Connecting the wire of the AM loop antenna
Connecting the FM and AM
antennas
Insert
Open the lever
Close the lever
Both FM and AM indoor antennas are supplied with this
unit. Connect each antenna correctly to the designated
terminals. In general, these antennas should provide
sufficient signal strength.
y
y
See right for connection information of the supplied AM loop
The wire of the AM loop antenna does not have any polarity
and you can connect either end of the wire to AM or GND
terminal.
antenna.
Notes
Assembling the supplied AM loop antenna
• The AM loop antenna should be placed away from this unit.
• The AM loop antenna should always be connected, even if an
outdoor AM antenna is connected to this unit.
• A properly installed outdoor antenna provides clearer reception
than an indoor one. If you experience poor reception quality,
install an outdoor antenna. Consult the nearest authorized
Yamaha dealer or service center about outdoor antennas.
Outdoor AM antenna
Use a 5 to 10 m (16 to 33
ft) vinyl-covered wire
extended outdoors from a
window.
AM loop
antenna
(supplied)
Indoor FM
antenna
(supplied)
Note
The types of the supplied AM loop antenna is different
depending on the models.
S
L
DOCK
ANTENNA
Connecting the power cable
AM
R
GND
Once all connections are complete, plug the power cable
into the AC wall outlet.
FM
U7NB5AL.
(U.S.A. model)
SUB
WOOFER
CENTER
TPUT
(U.S.A. model)
Ground (GND terminal)
For maximum safety and minimum interference, connect the
antenna GND terminal to a good earth ground. A good earth
ground is a metal stake driven into moist earth.
Power cable
20 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Setting the speaker impedance
Turning on and off the power
■ Turning on this unit
Caution
If you are to use 6 ohm speakers, set “SP IMP.” to
A
H
“6Ω MIN” as follows BEFORE using this unit.
Press STANDBY/ON (or POWER) to turn
on this unit.
y
A
1
Press STANDBY/ON on the front panel to
set this unit to the standby mode.
Refer to the right column for details.
When you turn on this unit, there will be a 4 to 5-second delay
before this unit can reproduce sound.
■ Set this unit to the standby mode
K
Press and hold TONE CONTROL and
2
A
I
Press STANDBY/ON (or STANDBY) to set
this unit to the standby mode.
A
then press STANDBY/ON to turn on this
unit.
In the standby mode, this unit consumes a small amount of
power in order to receive infrared signals from the remote
control.
This unit turns on, and the advanced setup menu
appears in the front panel display.
While holding
TONE CONTROL
down
STANDBY
/ON
L
Press PROGRAM l/ hto select “SP
IMP.”.
3
“SP IMP.” and the current speaker impedance setting
(“8Ω MIN”) appear in the front panel display.
M
Press STRAIGHT repeatedly to select
4
5
“6Ω MIN”.
A
Press STANDBY/ON to save the new
setting and turn off this unit.
Note
The setting you made is reflected next time you turn on this unit.
21 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Front panel display
Note
The XM and SIRIUS indicator is only applicable to the U.S.A. and Canada models and the cursor on the left of the XM indicator or
SIRIUS indicator lights up only when “XM” or “SIRIUS” is selected as the input source.
1
2
3
4
5
6
7
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R CD
TUNER
YPAO MEMORY
VIRTUAL AUTO TUNED STEREO
SLEEP HOLD
XM
SIRIUS
dB
DOCK
ENHANCER
VOL.
q
DIGITAL
SP
AB
MUTE
SILENT CINEMA
LFE
LL C R
PL
q
ft
neural
SL
SR
ms
dB
PCM
8
9
0 A
B
C
E
1 HDMI indicator
6 Tuner indicators
Lights up when the signal of the selected input source is
input at the HDMI IN jacks (see page 14).
Lights up when this unit is in the FM, AM, XM Satellite
pages 43 to 56).
2 DOCK indicator
7 MUTE indicator and VOLUME level indicator
•
Lights up when you station your iPod in a Yamaha
iPod universal dock (such as YDS-10, sold separately)
connected to the DOCK terminal of this unit (see
Flashes while the connected Yamaha Bluetooth adaptor
(such as YBA-10, sold separately) and the Bluetooth
component is in the paring (see page 59) or the
Bluetooth adaptor is searching the Bluetooth
component (see page 59).
•
The MUTE indicator flashes while the MUTE function
is on (see page 35).
•
Indicates the current volume level.
•
Lights up when this unit is reproducing PCM (Pulse Code
Modulation) digital audio signals.
9 Decoder indicators
The respective indicator lights up when any of the
decoders of this unit function.
•
Lights up while the connected Yamaha Bluetooth
page 19).
Lights up when headphones are connected (see page 35).
3 ENHANCER indicator
Lights up when the Compressed Music Enhancer mode is
selected (see page 38).
A SP A B indicators
Light up according to the set of front speakers activated
(see page 33).
SP A: The FRONT A speakers are activated.
SP B: The FRONT B speakers are activated.
4 Input source indicators
The corresponding cursor lights up to show the currently
selected input source.
5 YPAO indicator
Lights up when you run “AUTO SETUP” and when the
speaker settings set in “AUTO SETUP” are used without
any modifications (see page 24).
22 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
B CINEMA DSP indicator
Lights up when you select a CINEMA DSP sound
field program (see page 39).
The remote control transmits a directional infrared ray.
Be sure to aim the remote control directly at the remote
control sensor on this unit during operation.
VIRTUAL indicator
Lights up when Virtual CINEMA DSP is active (see
page 39).
SILENT CINEMA indicator
Lights up when headphones are connected and a
sound field program is selected (see page 39).
Approximately
6 m (20 ft)
30º
30º
C Multi-information display
Shows the name of the current sound field program and
other information when adjusting or changing settings.
D SLEEP indicator
Lights up while the sleep timer is on (see page 37).
E Input channel and speaker indicators
LFE indicator
Outputs infrared control signals. Aim this window at the
component you want to operate.
LFE
LL C R
Input channel indicators
SL
SR
y
To set the remote control codes for other components, see
page 75.
Input channel indicators
digital input signal.
• Light up or flash according to the settings of the
speakers when this unit is in the automatic setup
procedure (see page 24) or the speaker level setting
procedure in the “SP LEVEL” (see page 65).
Notes
• Do not spill water or other liquids on the remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperatures
– dusty places
23 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the speaker setting for your listening room
Optimizing the speaker setting for your listening room
This unit employs the YPAO (Yamaha Parametric Room Acoustic Optimizer) technology which lets you avoid
troublesome listening-based speaker setup and achieves highly accurate sound adjustments automatically. The supplied
optimizer microphone collects and this unit analyzes the sound your speakers produce in your actual listening
environment.
Using AUTO SETUP
2
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
Notes
• Be advised that it is normal for loud test tones to be output
during the “AUTO SETUP” procedure.
OPTIMIZER MIC
INFO
TUG AUTO/MAN'L
• To achieve the best results, make sure the room is as quiet as
possible while the “AUTO SETUP” procedure is in progress. If
there is too much ambient noise, the results may not be
satisfactory.
VIDEO AUX
R
VIDEO
L
AUDIO
PORTABLE
AUDIO SELECT
y
You can run “AUTO SETUP” using the system menu that appears
in the OSD or in the front panel display. This manual uses the
OSD illustrations to explain the “AUTO SETUP” procedure.
Optimizer
microphone
1
Make sure of the following check points.
The following display appears in the OSD.
Note
AUTO SETUP
Before starting the automatic setup, check the following
check points.
SETUP;;;;;;;AUTO
. START
❏
❏
❏
❏
Speakers are connected appropriately.
Headphones are disconnected from this unit.
This unit and the video monitor are turned on.
This unit is selected as the video input source of
the video monitor.
Automatic
Processing
of all item
[ ]/[ ]:Up/Down
[ ]/[ ]:Select
p
[
❏
❏
The connected subwoofer is turned on and the
volume level is set to about half way (or slightly
less).
The crossover frequency controls of the
connected subwoofer is set to the maximum.
3
Place the optimizer microphone at your
normal listening position on a flat level
surface with the microphone heading
upward.
Optimizer microphone
CROSSOVER
HIGH CUT
VOLUME
MIN
MAX
MIN
MAX
Controls of a subwoofer (example)
❏
❏
FRONT A speakers are selected as the front
speaker system (see page 33).
The room is sufficiently quiet.
y
It is recommended that you use a tripod (etc.) to affix the
optimizer microphone at the same height as your ears would be
when you are seated in your listening position. You can use the
attached screw of a tripod (etc.) to fix the optimizer microphone
to the tripod (etc.).
24 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the speaker setting for your listening room
8
Press ENTER to start the setup
procedure.
4
Make sure that “SETUP” is set to “AUTO”
and the pointer is pointing at “START”.
6
This unit starts the auto setup procedure. Loud test
tones are output from each speaker during the auto
setup procedure. Once all items are set, the result
display appears in the OSD.
y
You can also select the following setup methods. In this
8
8
case, press kto select “SETUP”, press l/ hto
select the one of the following choices and then select
“START”.
Notes
Choices: AUTO, RELOAD, UNDO, DEFAULT
• Select “AUTO” to automatically run the entire
“AUTO SETUP” procedure.
• During the auto setup procedure, do not perform any
operation on this unit.
• We recommend getting out of the room while this unit is in
the auto setup procedure. It takes approximately 3 minutes
for this unit to complete the auto setup procedure.
• Select “RELOAD” to reload the last “AUTO
SETUP” settings and override the previous
settings.
• Select “UNDO” to undo the last “AUTO SETUP”
settings and restore the previous settings.
• Select “DEFAULT” to reset the “AUTO SETUP”
parameters to the initial factory settings.
This unit performs the following checks:
Speaker wiring/volume level WIRING/LEVEL
Checks which speakers are connected and the
polarity of each speaker. Also checks and adjusts the
volume level of each speaker.
Note
“RELOAD” or “UNDO” is available only when you have
previously run “AUTO SETUP” and confirmed the results.
Speaker distance DISTANCE
Checks the distance of each speaker from the
listening position and adjusts the timing of each
channel.
8
Press nto select “START” and then press
5
8
ENTER to start the setup procedure.
The following message appears in the OSD.
Speaker size SIZE
NOTICE
Checks the frequency response of each speaker and
sets the appropriate low-frequency crossover for each
channel.
Loudꢀtestꢀtonesꢀare
ꢀꢀꢀoutput.
ꢀꢀꢀꢀ
ꢀ
Pleaseꢀkeepꢀquiet
orꢀleaveꢀtheꢀroom.
Pressꢀ[ENTER]
ꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
Before proceeding next operation
Once you perform the next operation, this unit starts the
automatic setup procedure. For more accurate
measurements, keep quiet and move to the wall where
speakers are not around. We recommend that you leave
the listening room during the automatic setup
procedure.
25 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the speaker setting for your listening room
The display changes as follows.
8
8
7
8
Press k and ENTER to display the
AUTO SETUP
setup results in detail.
SETUP;;;;;;;AUTO
. START
8
Press l/ hrepeatedly to toggle between
the setup result displays.
Automatic
Processing
of all item
[ ]/[ ]:Up/Down
[ENTER]:Start
Results of the speaker
connection and wiring
AUTO SETUP
Results of the speaker
distance from the
listening position
INITIALIZING
. WIRING/LEVEL
DISTANCE
SIZE
ꢀꢀ
WAITING;;;
;;;;;;;;;;
[ꢀ]:Exit
Results of the speaker
size
AUTO SETUP
RESULT
SP
DIST: 3.2/3.5m
LVL : -2/+2dB
SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
Results of the speaker
:
3/2/0.1
.
>
y
If you are not satisfied with the results or want to manually
adjust each parameter, run “MANUAL SETUP” (see
page 61).
The results displayed under “RESULT” are as follows.
Number of speakers SP
Displays the number of speakers connected to this unit in
the following order:
Note
Front/Back/Subwoofer
The distances displayed in the “DISTANCE” results may be
longer than the actual distance depending on the
characteristics of your speakers.
Speaker distance DIST
Displays the speaker distance from the listening position
in the following order:
8
9
Press ENTER to return to the result
Closest speaker distance/Farthest speaker distance
display.
AUTO:RESULT
. RESULT
Speaker level LVL
Displays the speaker output level in the following order:
Lowest speaker output level/Highest speaker output level
Notes
SP
DIST: 3.2/3.5m
LVL : -2/+2dB
SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Detail
:
3/2/0.1
• If “E-9:INTERNAL ERROR” appears during the testing
procedure, restart from step 4.
>
• If you selected “RELOAD” in step 4, no test tones are output.
• If an error occurs during the “AUTO SETUP” procedure, the
setup procedure is canceled and an error screen appears. For
details, see “If an error screen appears” on page 27.
• When this unit detects potential problems during the “AUTO
SETUP” procedure, “WARNING” and the number of warning
messages appears (see page 27).
26 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Optimizing the speaker setting for your listening room
■ If “WARNING” appears
8
8
10 Press n and then press l/ hto select
When this unit detects potential problems during the
“AUTO SETUP” procedure, “WARNING” appears in the
result display. Check the warning messages to correct your
speaker settings.
“SET” or “CANCEL”.
Choices: SET, CANCEL
• Select “SET” to confirm the “AUTO SETUP”
results.
Note
• Select “CANCEL” to cancel the “AUTO SETUP”
results.
Warnings differ from errors in that warnings do not cancel the
“AUTO SETUP” procedure.
8
11 Press ENTER to confirm your selection.
1
Make sure the pointer is pointing at
The top “SET MENU” display appears in the OSD.
8
“WARNING” and then press ENTER to
SET MENU
TOP MENU
display the detailed information about the
warning.
.
;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
The number on the right of “WARNING” indicates
the number of warning messages.
[ ]/[ ]:Up/Down
[ENTER]:Enter
AUTO SETUP
. WARNING(2)
RESULT
M
12 Press MENU to exit from “SET MENU”.
SP
:
3/2/0.1
DIST: 3.2/3.5m
LVL : -2/+2dB
SET CANCEL
[ ]/[ ]:Up/Down
[ENTER]:Detail
>
13 Disconnect the optimizer microphone from
this unit.
The optimizer microphone is sensitive to heat. Keep it
away from direct sunlight and do not place it on top
of this unit.
8
Press l/ hrepeatedly to toggle between
the warning displays.
2
y
WARNING
If you change speakers, speaker positions, or the layout of your
listening environment, run “AUTO SETUP” again to recalibrate
your system.
W-1:OUT OF PHASE
Reverse channel
AAAAFLAAAAA---
AAACENTER
AAAASLAAAAA---
■ If an error screen appears
[ ]/[ ]:Select
[ENTER]:Return
8
Press k/ n/ l/ hto select “RETRY” or
y
8
“EXIT” and then press ENTER.
The following display is an example where “E-8:USER
CANCEL” appears in the OSD.
• For details about each warning message, see the “AUTO
SETUP” section in “Troubleshooting” on page 84.
• When the corresponding warning message is not
applicable to a speaker, “––” is displayed instead.
ERROR
. E-8:USER CANCEL
Can't detect
signal at MIC
8
Press ENTER to return to the result
display.
3
RETRY EXIT
>
[ ]/[ ]:Select
[ENTER]:Enter
Choices: RETRY, EXIT
•
Select “RETRY” to retry the “AUTO SETUP”
procedure.
•
Select “EXIT” to exit from the “AUTO SETUP”
procedure.
27 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SELECTING THE SCENE TEMPLATES
Selecting the SCENE templates
This unit is equipped with 17 preset SCENE templates for
various situations of using this unit. As the initial factory
setting, the following SCENE templates are assigned to
each SCENE button:
O
5
2
Press INPUT l/ h(or press AMP and
8
then press l/ h) to select the desired
template.
l
INPUT
h
SCENE 1: DVD Viewing
SCENE 2: Disc Listening
SCENE 3: TV Viewing
SCENE 4: Radio Listening
Front panel
or
If you want to use other SCENE templates, you can select
the desired SCENE templates from the SCENE template
library and assign the templates to the selected SCENE
buttons on the front panel and the remote control.
AMP
ENTER
Select the desired SCENE
template
Remote control
1
DVD MovieꢀView
Assign the
SCENE
template to the
SCENE button
SCENE template library
(Image)
Q
6
3
Press the SCENE (or SCENE) button
again to confirm the selection.
The selected SCENE template is assigned to the
button.
Selecting the desired SCENE
template
1
1
or
Front panel
Remote control
Q
Press and hold the desired SCENE (or
1
6
SCENE) button for 3 seconds.
The indicator on the selected SCENE button on the
front panel starts to flash, and the name of the
currently assigned SCENE template appears in the
front panel display.
Note
Once the desired SCENE templates are assigned to the
corresponding SCENE buttons, you may need to set the input
source of the SCENE template on the remote control. See page 32
for details.
3 seconds
3 seconds
1
1
or
Front panel
Remote control
1
Flashes
DVD Viewing
28 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the SCENE templates
■ Which SCENE template would you like to select?
Which source do you like to
play back?
Which component do you
like for playback?
Default
SCENE buttons
SCENE templates
DVD Viewing
1
Video sources
(DVD video,
DVD
Recorded video)
DVD Movie Viewing
DVD Live Viewing
DVR
DVD
DVR Viewing
Music discs (CD, SACD
or DVD-Audio)
Disc Hi-fi Listening
Music Disc Listening
Disc Listening
2
CD
CD Hi-fi Listening
CD Listening
CD Music Listening
4
Radio programs
TUNER (FM/AM)
XM
Radio Listening
XM Listening
SIRIUS
SIRIUS Listening
iPod or Bluetooth
component
Dock Listening
DOCK
3
TV programs
Video games
DTV/CBL
V-AUX*
TV Viewing
TV Sports Viewing
Game Playing
Note
* When iPod is connected to the Yamaha iPod universal dock or a Bluetooth component is connected to the Bluetooth adapter, this unit
plays back the audio sources input at the DOCK terminal.
y
You can create your original SCENE templates by editing the preset SCENE templates. See page 31 for details.
29 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the SCENE templates
■ Preset SCENE templates descriptions
The illustrations of the SCENE button in the following table indicate the assigned SCENE buttons in the default setting.
SCENE template
Input source
DVD
Playback mode
STRAIGHT
Features
Select this SCENE template when you play back general
contents on the DVD player.
DVD Viewing
1
Select this SCENE template when you play back movies on
your DVD player.
DVD
DVD
DVR
MOVIE
Movie Dramatic
DVD Movie Viewing
DVD Live Viewing
DVR Viewing
Select this SCENE template when you enjoy the music live
video on your DVD player.
MUSIC
Pop/Rock
Select this SCENE template when you play back movies on
your digital video recorder.
MOVIE
Movie Dramatic
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your DVD player.
DVD
DVD
DIRECT
Disc Hi-fi Listening
Select this SCENE template when you play back music discs
on your DVD player.
STEREO
2ch Stereo
Music Disc
Listening
Select this SCENE template when you play back music
sources on your DVD player as the background music.
DVD
STEREO
5ch Stereo
Disc Listening
2
Select this SCENE template when you enjoy the high fidelity
sound of the music discs on your CD player.
CD
CD
DIRECT
CD Hi-fi Listening
CD Listening
Select this SCENE template when you play back music discs
on your CD player as the background music.
STEREO
5ch Stereo
Select this SCENE template when you play back music source
on your CD player.
CD
STEREO
2ch Stereo
CD Music Listening
Select this SCENE template when you enjoy FM or AM radio
programs.
TUNER
MUSIC ENHANCER
5ch Enhancer
Radio Listening
4
Select this SCENE template when you enjoy XM Satellite
Radio programs.
XM
MUSIC ENHANCER
5ch Enhancer
XM Listening
SIRIUS Listening
Dock Listening
Select this SCENE template when you enjoy SIRIUS Satellite
Radio programs.
SIRIUS
DOCK
MUSIC ENHANCER
5ch Enhancer
Select this SCENE template when you play back music on
your iPod stationed in a Yamaha iPod universal dock or
Bluetooth component that is connected to the Bluetooth
adapter.
MUSIC ENHANCER
5ch Enhancer
Select this SCENE template when you enjoy general
programs on your TV.
DTV/CBL
STRAIGHT
TV Viewing
3
Select this SCENE template when you enjoy sports programs
on your TV.
DTV/CBL
V-AUX
ENTERTAINMENT
TV Sports
TV Sports Viewing
Game Playing
Select this SCENE template when you play video games.
ENTERTAINMENT
Game
30 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the SCENE templates
Creating your original SCENE
templates
5
8
3
Press AMP and then k/ nto select the
desired parameter of the SCENE template
and then l/ hto select the desired value
8
You can create your original SCENE templates for each
SCENE button. You can refer to the preset 17 SCENE
templates to create the original SCENE templates.
of the selected parameter.
You can adjust the following parameters for a SCENE
template:
■ Customizing the preset SCENE
templates
• MODE:
The input source component
The active sound field programs,
STRAIGHT or DIRECT mode (see
pages 39 and 41)
The night listening mode setting (see
page 42)
Use this feature to customize the preset SCENE templates.
Create the original SCENE
template
Select a SCENE template
• NIGHT:
− SYSTEM: Keeps the current night listening
mode.
i n w g V i D e V
D
S C E N E :
− CINEMA: Sets the night listening mode to the
CINEMA mode.
D
: D V I N P U T
S C E N E
i n w g V i D e V D :
− MUSIC: Sets the night listening mode to the
MUSIC mode.
SCENE template library
(Image)
6
Press the SCENE button again to confirm
the edit.
4
1
1
Assign to the SCENE
button
y
An asterisk mark (*) appears by the name of the original SCENE
template.
1
2
Turn on the video monitor connected to this
unit.
Notes
• Once the desired SCENE templates are assigned to the
corresponding SCENE buttons, you may need to set the
input source of the SCENE template on the remote control. See
6
Press and hold the desired SCENE button
for 3 seconds.
6
The SCENE template customizing screen appears on
the video monitor.
page 32 for details.
• You can create a customized SCENE template for each
6
SCENE button, and if you create another customized
SCENE template, this unit overwrites the old customized
SCENE template with the new one.
1
• The newly created template is only available for the assigned
6
3 seconds
■ Renaming the SCENE templates
Note
Select the name of the SCENE template at step 3
of “Customizing the preset SCENE templates”
When the SCENE template you want to customize is not
assigned to any of the SCENE buttons, press AMP
and then press l/ hrepeatedly to recall the desired
SCENE template on the menu screen.
6
5
8
and then press ENTER.
8
8
•
Press k/ nto select the desired character.
8
•
Press l/ hto place “_” (underscore) under the
space or the desired character.
9
•
•
Press RETURN to cancel the new name.
8
Press ENTER to confirm the new name.
31 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the SCENE templates
Using remote control on the SCENE feature
components in the SCENE mode
You can operate both this unit and the input source
component by using the remote control. You must set the
appropriate remote control code for each input source in
advance (see page 75).
■ Setting input source of the customized
SCENE template on the remote control
If you customize the input source of the selected SCENE
template, you must set the input source of the SCENE
template on the remote control to operate the input source
component correctly.
6
Press the desired SCENE button on the
6
Press and hold the SCENE button and the
1
2
4
desired input selector button ( ) for 3 seconds.
remote control.
y
Press the desired buttons in the * area below
to control the input source component of the
selected SCENE template.
6
Press the SCENE button again to operate the input source
component.
POWER POWER
STANDBY
SIRIUS
POWER
MUTE
TV
AV
A
XM
CD
DVD
MD/CD-R TUNER
TV CH
DTV/CBL
B
DVR
C
V-AUX/DOCK
AMP
TV VOL
TV INPUT
TV MUTE
SCENE
*
1
2
3
4
SCENE buttons
BAND LEVEL
SRCH MODE
MENU
TITLE
VOLUME
ENTER
DISPLAY
RETURN
MEMORY
REC
INFO
l
PROG
h
ENHANCER SUR. DECODE
1
2
3
4
STRAIGHT DIRECT
NIGHT PARAMETER
5
6
7
8
MULTI CH IN AUDIO SEL
SLEEP
ENT
9
0
10
Note
*
These buttons control the input source component. See page 74
for details of the function of each button.
32 En
Download from Www.Somanuals.com. All Manuals Search And Download.
PLAYBACK
Playback
Caution
I
Rotate VOLUME (or press
5
Extreme caution should be exercised when you play
back CDs encoded in DTS. If you play back a CD
encoded in DTS on a DTS-incompatible CD player,
you will only hear some unwanted noise that may
damage your speakers. Check whether your CD player
supports CDs encoded in DTS. Also, check the sound
output level of your CD player before you play back a
CD encoded in DTS.
N
VOLUME +/–) to adjust the volume to the
desired output level.
L
6
Press PROGRAM l/ hrepeatedly (or
5
B
repeatedly) to select the desired sound field
program.
The name of the selected sound field program appears
in the front panel display.
See page 38 for details about sound field programs.
Basic operations
1
Turn on the video monitor connected to this
unit.
Movie Dramatic
Currently selected
J
2
3
Press SPEAKERS repeatedly to select the
surround field program
front speakers you want to use.
The respective speaker indicators lights up in the
front panel display.
Notes
• Choose a sound field program based on your listening
preference, not merely on the name of the program.
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
O
Press INPUT l/ hrepeatedly (or press
4
one of the input selector buttons ( )) to
select the desired input source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 34).
The name of the currently selected input source
appears in the front panel display for a few seconds.
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode (see page 39).
Available input sources
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R CD
TUNER
XM
SIRIUS
• To display information about the currently selected input source
in the OSD, see page 36 for details.
ꢀINPUT:ꢀDVD
■ A quick guide to contents
Currently selected input
source
See
When you want to...
page
4
Start playback on the selected component or
select a broadcast station.
• Refer to the operating instructions for the source
• See page 43 for details about FM/AM tuning
instructions.
• See page 46 for details about XM Satellite Radio
tuning instructions.
Enjoy high quality sound
41
41
40
42
35
39
37
Adjust the tonal quality of the front speakers
Adjust the parameters of sound field programs
Enjoy the sources with a wide dynamic range at night
Use headphones
Select a decoder to play back sources with
Automatically set this unit to the standby mode
• See page 51 for details about SIRIUS Satellite
Radio tuning instructions.
33 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Selecting audio input jacks
(AUDIO SELECT)
Selecting the MULTI CH INPUT
component
This unit comes with a variety of input jacks. Use this
feature (audio input jack select) to switch between input
jacks when more than one input jack is assigned to as the
same input source.
Use this feature to select the component connected to the
MULTI CH INPUT jacks (see page 18) as the input
source.
O
Press INPUT l/ hrepeatedly (or press
y
5
E
AMP and then MULTI CH IN) to select
• We recommend setting the audio input jack select to “AUTO”
in most cases.
• You can adjust the default audio input jack select of this unit by
using “AUDIO SELECT” in “OPTION MENU” (see page 71).
MULTI CH.
“MULTI CH” appears in the front panel display.
y
Use “MULTI CH SET” menu in “INPUT MENU” to set the
parameters for MULTI CH INPUT (see page 69).
P
5
Press AUDIO SELECT (or press AMP and
F
then AUDIO SEL) repeatedly to select the
Note
desired audio input jack select setting.
The input signals are amplified and output directly without sound
processing. Therefore, you cannot activate sound field programs,
the night listening mode, etc. while MULTI CH is selected as the
input source.
Available input sources
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R CD
TUNER
XM
SIRIUS
ꢀA.SEL:ꢀAUTO
Currently selected audio input jack select setting
AUDIO SELECT
Function
Automatically selects input signals in the
following order: (1) HDMI (2) Digital
signals (3) Analog signals
AUTO
Selects only HDMI signals. When HDMI
signals are not input, no sound is output.
HDMI
Selects only digital signals. When no
signals are input, no sound is output.
COAX/OPT
ANALOG
Selects only analog signals. If no analog
signals are input, no sound is output.
Note
(OPTICAL, COAXIAL and HDMI) are assigned. In addition,
HDMI is not available as an audio input jack select setting when
the HDMI IN DVD and HDMI IN DTV/CBL jacks are not used.
Use “INPUT ASSIGNMENT” in “INPUT MENU” to reassign
the respective input jack (see page 68).
34 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Displaying the current status of
this unit on a video monitor
You can display the operating information of this unit on a
video monitor.
Using your headphones
Connect a pair of headphones with a stereo
analog audio cable plug to the PHONES jack on
the front panel.
1
2
Turn on the video monitor connected to this
unit.
O
Press DISPLAY.
The current status screen appears in the OSD.
STATUSꢀꢀꢀꢀꢀꢀꢀꢀꢀVOL:-40dB
ꢀꢀꢀDVDꢀMovieꢀViewing
ꢀꢀꢀꢀꢀꢀꢀꢀꢀMOVIEꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀMovieꢀSpaciousꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀINPUT:ꢀꢀDVDꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀA.SEL:ꢀꢀHDMIꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀNIGHT:CINEMAꢀ(MID)ꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀ
y
y
You can select the amount of time that the current status is
displayed in the OSD by using the “OSD-AMP” parameter in
“OPTION MENU” (see page 70).
When you select a sound field program, SILENT CINEMA mode
is automatically activated (see page 39).
Notes
Note
• When you connect headphones, no signals are output at the
speaker terminals.
• All Dolby Digital and DTS audio signals are mixed down to the
left and right headphone channels.
The OSD signal is not output at the DVR VIDEO OUT jacks and
will not be recorded.
Muting the audio output
J
Press MUTE to mute the audio output. Press
J
y
I
N
• You can also rotate VOLUME or press VOLUME +/– to
resume the audio output.
• You can adjust the muting level by using the “MUTE TYPE”
parameter in “SOUND MENU” (see page 66).
• The MUTE indicator flashes in the front panel display when the
audio output is muted and disappears from the front panel
display when the audio output is resumed.
35 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
■ Audio information
Playing video sources in the
background of an audio source
You can combine a video image from a video source with
sound from an audio source. For example, you can enjoy
listening to classical music while viewing beautiful
scenery from the video source on the video monitor.
Information
Descriptions
Signal format. When this unit cannot detect a
digital signal, it automatically switches to
analog input.
FORMAT
The number of samples per second taken from
a continuous signal to make a discrete signal.
SAMPLING
CHANNEL
The number of source channels in the input
signal (front/surround/LFE). For example, a
multi-channel soundtrack with 3 front
channels, 2 surround channels and LFE, is
displayed as “3/2/0.1”.
4
Press the input selector buttons ( ) control to
select a video source and then an audio source.
XM
SIRIUS
Audio sources
Video sources
The number of bits passing a given point per
second.
BITRATE
FLAG
CD
DVD
MD/CD-R TUNER
DTV/CBL
DVR
Flag data encoded in DTS, Dolby Digital, or
PCM signals that cue this unit to automatically
switch decoders.
V-AUX
Note
y
“–––” appears when this unit cannot display the corresponding
information.
• You can also select “MULTI CH” as the audio source (see
5
E
page 34). Press AMP and then press MULTI CH IN.
• Set the “BGV” parameter in the “MULTI CH SET” menu to the
desired setting to select the default background video input
source of the MULTI CH INPUT sources (see page 69).
■ Video information
Information
Descriptions
Type of the source video signals and the
video signals output at the HDMI OUT
jack of this unit.
HDMI SIGNAL
Displaying the input source
information
You can display the format, sampling frequency, channel,
bit rate and flag data of the current input signal.
output at the HDMI IN/OUT jacks of this
unit.
HDMI RES.
Error message for HDMI sources or
connected HDMI devices. See “HDMI
error and message” for details.
HDMI ERROR
(Only when error
is detected)
5
M
1
Press AMP and then MENU.
The top “SET MENU” display appears in the OSD.
SET MENU
TOP MENU
Note
.
;AUTO SETUP
;MANUAL SETUP
.A;SIGNAL INFO
“–––” appears when this unit cannot display the corresponding
information.
[ ]/[ ]:Up/Down
[ENTER]:Enter
HDMI error and message
Message
Cause
8
Press nrepeatedly to select “SIGNAL
8
INFO” and then press ENTER.
The audio information about the input source appears
in the OSD.
2
The number of the connected HDMI
components is over the limit.
DEVICE OVER
HDCP authentication failed.
HDCP ERROR
OUT OF RES.
The connected monitor is not compatible
with the resolution of the input video signal.
8
Press l/ hto toggle between the audio
and video information displays.
3
4
M
Press MENU again to exit from “SET
MENU”.
36 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Playback
Using the sleep timer
Use this feature to automatically set this unit to the
standby mode after a certain amount of time.
5
T
Press AMP and then press SLEEP
repeatedly to set the amount of time.
T
Each time you press SLEEP, the front panel display
changes as shown below.
SLEEP 120min
SLEEP OFF SLEEP 30min
SLEEP 90min
SLEEP 60min
The SLEEP indicator flashes while you are switching the
amount of time for the sleep timer. Once the sleep timer is
set, the SLEEP indicator lights up in the front panel
display, and the display returns to the selected sound field
program.
y
5
• To cancel the sleep timer, press AMP and then press
T
SLEEP repeatedly until “SLEEP OFF” appears in the front
panel display.
• The sleep timer setting can also be canceled by pressing
A
I
STANDBY/ON (or STANDBY) to set this unit to the
standby mode.
37 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SOUND FIELD PROGRAMS
Sound field programs
This unit is equipped with a variety of precise digital
decoders that allow you to enjoy multi-channel playback
from almost any stereo or multi-channel sound source.
Notes
• When you select an input source, this unit automatically selects
the last sound field program used with the corresponding input
source.
• Sound field programs cannot be selected when the component
connected to the MULTI CH INPUT jacks is selected as the
input source (see page 34).
• When PCM signals with a sampling frequency higher than 48
kHz are input, this unit is automatically set to the “STRAIGHT”
mode (see page 39).
L
5
Press PROGRAM l/ h(or press AMP and
B
then press PROG l/ hrepeatedly).
The name of the selected sound field program appears in
the front panel display.
y
Choose a sound field program based on your listening preference,
not merely on the name of the program itself.
Sound field program descriptions
Category
Program
Features
CINEMA DSP processing. This program presents an image of pop, rock, or jazz live
concert. The sound field reproduces the spaciousness of a massive pavilion with an emphasis
on the vividness of vocals on the stage and solo instruments and the beats of rhythm
instruments.
Pop/Rock
MUSIC
CINEMA DSP processing. This sound field is suitable for classic and orchestral music. The
program uses data collected in a large concert hall in Munich. You can enjoy delicate and
beautiful reverberation and a majestic atmosphere.
Hall
CINEMA DSP processing. The sound field is suitable for jazz and fusion music. It uses data
collected in a famous jazz club in New York. You can enjoy clear reverberation.
Jazz
Game
CINEMA DSP processing. You can enjoy dynamic and thrilling sound effects as you play
games. The program lets you feel the depth and three-dimensional surrounding sounds of the
field where you are playing, and offers cinema-like surrounding sound effects for the scenes
of movies.
ENTERTAINMENT
CINEMA DSP processing. You can enjoy sports relays broadcast in stereo and variety shows
with a live sound environment. For sports relays, the voices of commentators and
announcers come clearly from the center; the cheers and atmosphere in the stadium spread
around within a comfortable range, and you can feel like as if you are in the stadium.
TV Sports
CINEMA DSP processing. The sound field is suitable for movies with an emphasis on
spectacular sound effects, and is a perfect fit with a wide screen. The program reproduces a
wide dynamic range from minimum sound effects to powerful sounds.
Movie Spacious
Movie Dramatic
MOVIE
CINEMA DSP processing. This sound field is also suitable for movies with an emphasis on
three-dimensional sound effects. It restrains reverberation to an moderate extent, but
reproduces sound effects and background music in a soft, three-dimensional manner with
clarity and center orientation of voices as pivots.
Downmixes multi-channel sources to 2 channel or plays back 2-channel sources as they are.
2ch Stereo
5ch Stereo
STEREO
CINEMA DSP processing. Using this program increases the listening position range. This is
a sound field suitable for background music at parties.
Select these programs to play back compression artifacts (such as the MP3 format) in
2-channel or 5-channel stereo. This program enhances your listening experience by
regenerating the missing harmonics in a compression artifact.
2ch Enhancer
5ch Enhancer
MUSIC
ENHANCER
Note
The sound field programs of this unit are recreations of real-world acoustic environments made from precise measurements taken in the
actual concert hall, music venue, movie theater, etc. Thus, you may notice variations in the strength of the reflections coming from each
direction.
38 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound field programs
■ Enjoying 2-channel sources using the
standard decoders
■ Using sound field programs without
surround speakers
Signals input from 2-channel sources can also be played
back on multi-channels.
(Virtual CINEMA DSP)
Virtual CINEMA DSP allows you to enjoy the CINEMA
virtual speakers.
If you set “SUR. L/R SP” to “NONE” (see page 64),
Virtual CINEMA DSP is automatically activated
whenever you select a CINEMA DSP program
(see page 38).
5
Press AMP and then press
QSUR. DECODE
repeatedly to select a decoder.
You can select from the following decoders depending on
the type of source you are playing and your personal
preference.
Note
Decoder
Functions
Virtual CINEMA DSP will not be activated even when
“SUR. L/R SP” is set to “NONE” (see page 64) in the following
cases:
Dolby Pro Logic processing for any
sources
Pro Logic
– when “5ch Stereo” (see page 38) is selected.
– when headphones are connected to the PHONES jack.
Dolby Pro Logic II processing for
movie sources
PLII Movie
PLII Music
PLII Game
■ Enjoying multi-channel sources and
sound field programs with headphones
(SILENT CINEMA)
SILENT CINEMA allows you to enjoy multi-channel
sources, through ordinary headphones. SILENT CINEMA
is automatically activated whenever you connect
headphones to the PHONES jack while listening to
CINEMA DSP sound field programs (except for 5ch
Stereo) (see page 38). When activated, the SILENT
CINEMA indicator lights up in the front panel display.
Dolby Pro Logic II processing for
music sources
Dolby Pro Logic II processing for
game sources
Neural Surround processing for any
sources
Neural Sur.
■ Enjoying unprocessed input sources
(Straight decoding mode)
When this unit is in the “STRAIGHT” mode,
multi-channel sources are decoded straight into the
appropriate channels without any additional effect
processing. 2-channel stereo sources are output from only
the front left and right speakers.
M
5
Press STRAIGHT (or press AMP and then
C
press STRAIGHT) to select “STRAIGHT”.
To deactivate the “STRAIGHT” mode, press
M
C
5
STRAIGHT (or press AMP and then
STRAIGHT) again so that “STRAIGHT” disappears
from the front panel display.
39 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound field programs
y
■ Editing sound fields parameters
Initial settings are indicated in bold under each parameter.
You can enjoy good quality sound with the factory default
parameters. Although you do not have to change the initial
settings, you can change some of the parameters to better
suit the input source or your listening room.
For Pop/Rock, Hall, Jazz, Game, TV Sports,
Movie Spacious and Movie Dramatic:
DSP level DSP LEVEL
Function:
Choices:
Adjusts the effect level.
MIN, MID, MAX
5
While listening to a source, press AMP
1
2
3
S
and then press PARAMETER.
For 2ch Enhancer and 5ch Enhancer:
8
Press k/ nto select the desired parameter
you want to change.
Effect level EFFECT LEVEL
Function:
Choices:
Adjusts the effect level.
LOW, HIGH
8
value.
For Pro Logic II Music:
Panorama PANORAMA
Note
Function:
Sends stereo signals to the surround
You cannot change parameter values when “MEMORY GUARD”
in “OPTION MENU” is set to “ON” (see page 70).
speakers as well as the front speakers for
a wraparound effect.
Choices:
OFF, ON
Dimension DIMENSION
Function: Gradually adjusts the sound field either
towards the front or towards the rear.
Control range: –3 (towards the rear) to +3 (towards the
front), initial setting is STD (standard).
Center width CT WIDTH
Function:
Adjusts the center image from all three
front speakers to varying degrees. A
larger value adjusts the center image
towards the front left and right speakers.
Control range: 0 (center channel sound is output only
from center speaker) to 7 (center channel
sound is output only from front left and
right speakers), initial setting is 3.
40 En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING AUDIO FEATURES
Using audio features
Enjoying high quality sound
Adjusting the speaker level
Use the DIRECT mode to enjoy the high quality sounds of
the selected source. When the DIRECT mode is activated,
this unit plays back the selected source with the least
circuitry.
You can adjust the output level of each speaker while
playing sources input at the MULTI CH INPUT jacks.
Note
NDIRECT
DIRECT) to select “DIRECT”.
5
(or press AMP and then
Press
D
This operation will override the level adjustments made in
“AUTO SETUP” (see page 24) and “SP LEVEL” (see page 65).
Notes
5
7
1
Press AMP and then press LEVEL on
8
the remote control and then k/ nto select
the speaker you want to adjust.
• “TONE CONTROL” and “SOUND MENU” (see page 63)
settings (except for speaker level settings) are not effective.
• The front panel display automatically dims.
y
Display
FRONT L
FRONT R
CENTER
SWFR
Adjusted speaker
Front left speaker
While DIRECT mode is activated, the front panel display turns on
momentarily when an operation is performed.
Front right speaker
Center speaker
Adjusting the tonal quality
Use this feature to adjust the balance of bass and treble for
the front left and right speaker channels.
Subwoofer
Surround left speaker
Surround right speaker
y
SUR. L
SUR. R
Speaker and headphone adjustments are stored independently.
K
1
2
Press TONE CONTROL repeatedly to
select the high-frequency response
(TREBLE) or the low-frequency response
(BASS).
y
• The available speaker channels differ depending on the
setting of the speakers.
• When the video monitor is turned on, the “SPEAKER
LEVEL” adjustment menu appears in the video monitor.
L
Press PROGRAM l/ hrepeatedly to
8
Press l/ hto adjust the speaker output
level.
• Press hto increase the value.
• Press lto decrease the value.
2
3
adjust the high-frequency response
(TREBLE) or the low-frequency response
(BASS).
8
8
• Control range: –10 dB to +10 dB
Notes
• If you increase or decrease the high-frequency or the
low-frequency sound to an extreme level, the tonal quality of
the surround speakers may not match.
7
Press LEVEL to turn off the speaker level
adjustment display.
• TONE CONTROL is not effective when this unit is in the
DIRECT mode, or when MULTI CH is selected as the input
source.
41 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using audio features
Selecting the night listening mode
The night listening modes are designed to improve
listenability at lower volumes or at night.
5
R
1
Press AMP and then NIGHT repeatedly
to select “NIGHT:CINEMA” or
“NIGHT:MUSIC”.
Choices: NIGHT:CINEMA, NIGHT:MUSIC, OFF
• Select “NIGHT:CINEMA” when watching films to
reduce the dynamic range of film soundtracks and
make dialog easier to hear at lower volumes.
• Select “NIGHT:MUSIC” when listening to music
sources to preserve ease-of-listening for all sounds.
• Select “OFF” if you do not want to use this feature.
y
When a night listening mode is selected, the NIGHT
indicator lights up in the front panel display.
8
Press l/ hto adjust the effect level while
“NIGHT:CINEMA” or “NIGHT:MUSIC” is
displayed in the front panel display.
2
Effect.Lvl:MID
Choices: MIN, MID, MAX
• Select “MIN” for minimum compression.
• Select “MID” for standard compression.
• Select “MAX” for maximum compression.
y
stored independently.
Notes
• You cannot use the night listening modes in the following cases:
– when the DIRECT mode (see page 41) is selected.
– when the component connected to the MULTI CH INPUT
jacks is selected as the input source (see page 34).
– when headphones are connected to the PHONES jack.
• The night listening modes may vary in effectiveness depending
on the input source and surround sound settings you use.
42 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FM/AM TUNING
FM/AM tuning
There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and
there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use
the automatic and manual preset tuning features to store up to 40 stations.
Automatic tuning
Manual tuning
Automatic tuning is effective when station signals are
strong and there is no interference.
If the signal received from the station you want to select is
weak, tune into it manually.
Note
OINPUT
l/ hrepeatedly so that
“TUNER” is displayed in the front panel
display.
1
Press
Manually tuning into an FM station automatically switches the
tuner to monaural reception to increase the signal quality.
OINPUT
l/ hrepeatedly so that
“TUNER” is displayed in the front panel
display.
1
Press
CBAND
to select the reception band
(FM or AM).
2
3
Press
HTUNING AUTO/MAN’L
Press
so that the
CBAND
to select the reception band
(FM or AM).
2
3
Press
AUTO indicator lights up in the front panel
display.
Lights up
HTUNING AUTO/MAN’L
Press
so that the
AUTO indicator disappears from the front
AUTO
panel display.
AꢀFM 88.9 MHz
No colon (:)
AꢀFM 88.9 MHz
No colon (:)
If a colon (:) appears in the front panel display,
automatic tuning is not possible. Press
B
PRESET/TUNING to turn the colon (:) off.
If a colon (:) appears in the front panel display,
manual tuning is not possible. Press
EPRESET/TUNING/CH
l/ honce
to begin automatic tuning.
4
Press
B
PRESET/TUNING to turn the colon (:) off.
When this unit is tuned into a station, the TUNED
indicator lights up and the frequency of the received
station is shown in the front panel display.
EPRESET/TUNING/CH
l/ hto
tune into the desired station manually.
4
Press
y
Lights up
Hold down the button to continue searching.
TUNED
AꢀFM 88.9 MHz
43 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FM/AM tuning
Automatic preset tuning
Manual preset tuning
You can use the automatic preset tuning feature to store
FM stations with strong signals up to 40 (A1 to E8: 8
preset station numbers in each of the 5 preset station
groups) of those stations in order. You can then recall any
preset station easily by selecting the preset station number.
station numbers in each of the 5 preset station groups)
manually.
1
2
Tune into a station automatically or manually.
See page 43 for tuning instructions.
OINPUT
l/ hrepeatedly so that
1
Press
“TUNER” is displayed in the front panel
display.
FMEMORY
Press
.
The MEMORY indicator flashes in the front panel
display for approximately 30 seconds.
CBAND
to select “FM” as the
reception band.
2
3
Press
DA/B/C/D/E
Press and
EPRESET/TUNING/CH
3
l/ hrepeatedly
to select a preset station group (A1 to E8)
while the MEMORY indicator is flashing.
Check that the colon (:) appears in the front panel
display.
FMEMORY
Press and hold
seconds.
for more than 3
The preset station number as well as the MEMORY
and AUTO indicators flashes. After approximately 5
seconds, automatic presetting starts from the current
frequency and proceeds toward the higher
frequencies.
Flashes
MEMORY
Flashes
A3:FM 88.9 MHz
MEMORY
AUTO
Preset station Colon (:)
group and
A1:FM 88.9 MHz
Flashes
number
FMEMORY
while the MEMORY
indicator is flashing.
The station band and frequency appear in the front
panel display with the preset station group and
number you have selected.
4
Press
When automatic preset tuning is completed, the front
panel display shows the frequency of the last preset
station.
y
You can select the preset station group and the preset station
number where the first received station will be stored by pressing
TUNED
DA/B/C/D/E
EPRESET/TUNING/CH
l/ h.
and then
A1:FM 88.9 MHz
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• Only FM stations with sufficient signal strength are stored
automatically by automatic preset tuning. If the station you
want to store is weak in signal strength, tune into it manually
and store it as described in “Manual preset tuning” on this page.
The displayed station has been stored as A1.
Notes
• Any stored station data existing under a preset station number is
cleared when you store a new station under the same preset
station number.
• The reception mode (stereo or monaural) is stored along with
the station frequency.
44 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FM/AM tuning
Selecting preset stations
Exchanging preset station
You can tune into any desired station simply by selecting
the preset station group and number under which it was
stored.
You can exchange the assignments of two preset stations
with each other. The example below describes the
procedure to exchange preset station “E1” with “A5”.
y
DA/B/C/D/E
l/ h.
See “Selecting preset stations” on this page.
1
2
Select preset station “E1” using
EPRESET/TUNING/CH
When performing this operation with the remote control, press
4TUNER to select “TUNER” as the input source.
and
DA/B/C/D/E
repeatedly to select the desired preset
station group (A to E).
The preset station group letter appears in the front
panel display and changes each time you press the
button.
8A-E/CAT.
l/ h)
1
2
Press
(or
BPRESET/TUNING
Press and hold
more than 3 seconds.
for
“E1” and the MEMORY indicator flash in the front
panel display.
Flashes
EPRESET/TUNING/CH
Press
l/ h(or
8PRESET/CH
k/ n) to select the desired
MEMORY
preset station number (1 to 8).
The preset station group and number appear in the
front panel display along with the station band and
frequency.
E1:FM 88.9 MHz
Flashes
DA/B/C/D/E
l/ h.
3
Select preset station “A5” using
EPRESET/TUNING/CH
and
E1:FM 88.9 MHz
“A5” and the MEMORY indicator flash in the front
y
panel display.
You can select the desired preset station number (1 to 8) directly
by pressing the numeric buttons on the remote control.
Flashes
MEMORY
A5:FM 88.9 MHz
Flashes
BPRESET/TUNING
again.
4
Press
“EXCHANGE E1–A5” appears in the front panel
display and the assignments of the two preset stations
are exchanged.
45 En
Download from Www.Somanuals.com. All Manuals Search And Download.
XM SATELLITE RADIO TUNING
XM Satellite Radio tuning
XM Radio offers an extraordinary variety of commercial-free music, plus the best in premier sports, news, talk radio,
stand-up comedy, children’s and entertainment programming. XM is broadcast in superior digital audio quality from
coast to coast. From rock to reggae, from classical to hip hop, XM has something for every music fan.
XM Satellite Radio online information
For U.S. customers: http://www.xmradio.com/
For Canadian customers: http://www.xmradio.ca/
Note
The XM Satellite Radio service is only available in the 48 contiguous United States (not available in Alaska and Hawaii) and Canada.
XM READY legal disclaimer
XM monthly service subscription sold separately. XM Mini-Tuner and Home Dock required (each sold separately) to receive XM
service. It is prohibited to copy, decompile, disassemble, reverse engineer, hack, manipulate or otherwise make available any
technology or software incorporated in receivers compatible with the XM Satellite Radio System. Installation costs and other fees
and taxes, including a one-time activation fee may apply. All fees and programming subject to change. Channels with frequent
explicit language are indicated with an XL. Channel blocking is available for XM radio receivers by calling 1-800-XM-RADIO (US
residents) and 1-877-GET-XMSR (Canadian residents). For a full listing of the XM commercial- free channels and
advertising-supported channels, visit lineup.xmradio.com (US residents) or xmradio.ca (Canadian residents). Subscriptions subject
to Customer Agreement available at www.xmradio.com (US residents) and www.xmradio.ca (Canadian residents). Only available
in the 48 contiguous United States and Canada. ©2008 XM Satellite Radio Inc. All rights reserved. All other trademarks are the
property of their respective owners.
Connecting the XM Mini-Tuner Dock
Connect XM Mini-Tuner and XM Mini-Tuner Dock (sold
separately) to the XM jack on the rear panel of this unit.
For details, see the operating instructions provided with
XM Mini-Tuner Dock.
y
To ensure optimal reception of the XM Satellite Radio signals,
the XM Mini-Tuner Dock must be placed at or near a southerly
facing window with no obstacles in the path to the sky. You can
mount it indoors or outdoors. Use the “XM RADIO SET” screen
in the video monitor (see page 72) to check the antenna reception
level and adjust the orientation of the antenna.
Note
If “CHECK ANTENNA” or “CHECK XM TUNER” appears in
the front panel display, the connection and setting of the antenna,
Home Dock, or XM Mini-Tuner may not correct (see page 82).
XM Mini-Tuner and XM Mini-Tuner Dock
(sold separately)
SIRIUS
DTV/CBL
DOCK
XM
ANTENNA
P
B
Y
B
AM
DVR
C
GND
FM
U7NB5AL.
ER
SUB
WOOFER
CENTER
B
ER
OUTPUT
46 En
Download from Www.Somanuals.com. All Manuals Search And Download.
XM Satellite Radio tuning
Activating XM Satellite Radio
Basic XM Satellite Radio
operations
Once you have installed the XM Mini-Tuner Dock,
inserted the XM Mini-Tuner, connected the XM
®
Mini-Tuner Dock to your XM Ready home audio
O
Press INPUT l/ hrepeatedly (or press
1
system, and installed the antenna, you are ready to
subscribe and begin receiving XM programming. There
are three places to find your eight character XM Radio ID:
on the XM Mini-Tuner, on the XM Mini-Tuner package,
and on XM Channel 0. Record the Radio ID in the
following eight squares for reference.
3
XM) to select “XM” as the input source.
The cursor on the left of the XM indicator lights up in
the front panel display and the XM Satellite Radio
information (such as channel number, channel name,
category, artist name, or song title) for the currently
selected channel appears in the front panel display.
Lights up
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R CD
TUNER
XM
SIRIUS
Note
The XM Radio ID does not use the letters “I”, “O”, “S” or “F”.
Activate your XM Satellite Radio service in the U.S. online at
http://www.xmradio.com/ or call 1-800-XM-RADIO
001ꢀPreview
y
(1-800-967-2346). You will need a major credit card. XM will
send a signal from the satellites to activate the full channel lineup.
Activation normally takes 10 to 15 minutes, but during peak busy
periods you may need to keep your XM Ready home audio
system on for up to an hour. When you can access the full channel
lineup on your XM Ready home audio system you are done. For
more information or to subscribe in Canada, visit XM on the Web
at www.xmradio.ca or call XM’s Listener Care at
When you select “XM” as the input source, this unit
automatically recalls the previously selected channel.
Notes
• The XM Satellite Radio signals cannot be output at the
AUDIO OUT (REC) jacks.
• If a status message or an error message appears in the front
panel display or in the OSD, see the “XM Satellite Radio”
section in “Troubleshooting” on page 78 for appropriate
remedies.
1-877-GET-XMSR (1-877-438-9677).
2
Satellite Radio search modes.
“All Channel Search mode” on page 48.
• To select a channel from the preset channels, see
“Preset Search mode” on page 48.
• To select the desired channel directly by entering
mode” on page 48.
y
• You can use the Neural Surround decoder to enjoy the XM HD
surround sound content of the XM Satellite Radio broadcasts in
multi-channels (see page 39).
• You can set the XM Satellite Radio preset channels (see
page 49).
• You can display the XM Satellite Radio information in the front
panel display or in the OSD (see page 50).
47 En
Download from Www.Somanuals.com. All Manuals Search And Download.
XM Satellite Radio tuning
y
Before performing operations, press 3XM to select “XM” as the
input source.
EPRESET/TUNING/CH
3
Press
8PRESET/CH
l/ h(or
k/ n) repeatedly to change
the preset channel number (1 to 8).
■ All Channel Search mode
y
BSEARCH MODE MSRCH
(or
) repeatedly to select “ALL CH
You can also select the preset channel number directly by
pressing the numeric buttons (1 to 8) on the remote control.
1
Press
MODE
SEARCH”.
■ Direct Number Access mode
EPRESET/TUNING/CH
k/ n) repeatedly to search
for a channel within all channels.
2
Press
8PRESET/CH
l/ h(or
MSRCH MODE
repeatedly to select
“ALL CH SEARCH” or “CAT SEARCH”.
1
2
Press
G
Press the numeric buttons ( ) to enter the
y
• You can search for a channel quickly by pressing and holding
desired three-digit channel number.
For example, to enter the number 123, press the
numeric buttons as shown below.
EPRESET/TUNING/CH 8PRESET/CH
l/ h(or
k/ n).
• To display the XM Radio ID number displayed in the front
panel display, select channel “0”.
1
2
3
■ Category Search mode
BSEARCH MODE
MSRCH
1
2
3
Press
MODE
(or
) repeatedly to select “CAT SEARCH”.
The display changes as follows.
DCATEGORY
8A-E/CAT.
l/ h)
Press
(or
repeatedly to change the channel category.
<XM> --1
EPRESET/TUNING/CH
Press
8PRESET/CH
l/ h(or
k/ n) repeatedly to search
for a channel within the selected channel
category.
<XM> -12
<XM>123
y
You can search for a channel quickly by pressing and holding
l/ h(or
k/ n).
■ Preset Search mode
Prior to selecting a preset channel in the Preset Search
mode, you must preset XM Satellite Radio channels. For
details, see “Setting XM Satellite Radio preset channels”
on page 49.
y
• To enter a one-digit or two-digit channel number, press the
y
G
TENT
TENT
numeric buttons ( ) and then press
to confirm the
to tune into the
All preset channels (A1 to E8) recalls “001 Preview” by the initial
factory setting.
input number. Instead of pressing
channel immediately, you can wait a few seconds until this unit
confirms the entered channel number.
G
TENT
• Pressing a button other than the numeric buttons ( ) or
BSEARCH MODE MSRCH
(or
) repeatedly to select “PRESET
1
2
Press
MODE
cancels the Direct Number Access mode procedure.
SEARCH”.
DCATEGORY
8A-E/CAT.
l/ h)
Press
(or
repeatedly to change the preset channel
group (A to E).
48 En
Download from Www.Somanuals.com. All Manuals Search And Download.
XM Satellite Radio tuning
Setting XM Satellite Radio preset
channels
Radio channels (A1 to E8: 8 preset channel numbers in
each of the 5 preset channel groups). You can then recall
any preset channel easily by selecting the preset channel
group and number as described in “Preset Search mode”
on page 48.
DCATEGORY
8A-E/CAT.
l/ h)
3
4
5
Press
(or
repeatedly to select a preset channel group
(A to E) while the MEMORY indicator is
flashing.
The preset channel group letter appears in the front
panel display.
Flashes
MEMORY
1
Search for a channel you want to set as a
preset channel by using one of the XM
Satellite Radio search modes.
C- 043ꢀXMU
Selected preset channel group
See “Basic XM Satellite Radio operations” on
page 47 for details.
EPRESET/TUNING/CH
Press
8PRESET/CH
l/ h(or
k/ n) repeatedly to select a
preset channel number (1 to 8) while the
MEMORY indicator is flashing.
The preset channel number appears in the front panel
display.
043ꢀXMU
Currently selected channel number
Flashes
FMEMORY
The MEMORY indicator flashes in the front panel
9MEMORY
).
2
Press
(or
MEMORY
display for approximately 30 seconds.
C5 043ꢀXMU
Selected preset channel number
MEMORY
Flashes
FMEMORY
9MEMORY
) to set
Press
(or
the selected XM Satellite Radio channel as a
preset channel while the MEMORY indicator
is flashing.
A colon (:) appears next to the preset channel number
for confirmation, and the MEMORY indicator turns
off in the front panel display.
Note
You must proceed to and carry out steps 3 through 5 while
the MEMORY indicator is flashing in the front panel
display.
C5:043ꢀXMU
Colon (:)
Note
Once you set a new preset channel, the one previously stored in
the same preset channel group and number is cleared.
49 En
Download from Www.Somanuals.com. All Manuals Search And Download.
XM Satellite Radio tuning
y
• The front panel display can indicate up to 14 alphanumeric
characters at once. You can set whether to display the XM
Satellite Radio information in the front panel display in a
continuous manner or by 14 alphanumeric characters at once by
using the “FL SCROLL” parameter in “OPTION MENU” (see
page 70).
• If the XM Satellite Radio information contains a character that
cannot be recognized by this unit, the character will be
displayed with a space.
Displaying the XM Satellite Radio
information
You can display the XM Satellite Radio information (such
as channel number, channel name, category, artist name,
or song title) for the currently selected channel in the front
panel display or in the OSD.
Note
8
• To hold the current XM Raido information, press ENTER on
8
the remote control while it is being displayed. Press ENTER
again to release the held information.
If a status message or an error message appears in the front panel
display or in the OSD, see the “XM Satellite Radio” section in
“Troubleshooting” on page 82 for appropriate remedies.
• When the antenna of the XM Mini-Tuner Dock cannot receive
the signals, “NO SIGNAL” appears in the front panel display.
■ Displaying the XM Satellite Radio
■ Displaying the XM Satellite Radio
information in the front panel display
information in the OSD
H
A
Press INFO (or INFO) repeatedly to toggle
between the following XM Satellite Radio
information display modes.
ODISPLAY
The following screen is displayed in the OSD.
Press
.
XM INFORMATION
Channel number/name
Channel category
ALL CH SEARCH
: 043
[1]
XM
CHAN : XMU
[5]
[2]
CAT
: Rock
NAME : Coldplay
TITLE : Speed of sound
.(Spe / Coldplay)
[ ]/[ ]: CHANNEL
[3]
[ ]/[ ]: CATEGORY
[
[
Artist name/song title
[1] Search mode (see page 48)
[2] Channel category
[3] Song title
When the channel number / name is displayed:
[4] Channel number/name
[5] Artist name
[043] XMU
y
ODISPLAY
• XM status messages also appear in the OSD.
• To turn off the OSD, press
again.
When the channel category is displayed:
• You can select the amount of time the XM Satellite Radio
information is displayed in the OSD by using the
“OSD-SOURCE” parameter in “OPTION MENU” (see
page 70).
<CAT>ROCK
8
• To hold the XM Satellite Radio information, press ENTER
on the remote control while it is being displayed in the OSD.
The HOLD indicator flashes in the front panel display while
When the artist name / song title is displayed:
8
you are holding the XM information. Press ENTER again or
change the XM Satellite Radio channel to release the held
information.
Coldplay / Clo
50 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SIRIUS SATELLITE RADIO™ TUNING
SIRIUS Satellite Radio™ tuning
SIRIUS Satellite Radio provides over 130 channels of exclusive entertainment and 100% commercial-free music. Only
SIRIUS has more than 65 original music channels, from today's hits to R&B, oldies and classical masterpieces. From
authentic country and real bluegrass to cool jazz, hot latin, reggae, rock and many more. Best of all, it’s all 100%
commercial-free.
SIRIUS also has more than 55 channels of world-class sports, news and entertainment. Included as part of your
subscription, you get up to 16 NFL games a week, up to 40 NBA games a week and up to 40 NHL games a week. (Games
are broadcast during their respective seasons.)
Coupled with great sports news from ESPN, the SIRIUS sports offering is unrivaled. And don’t forget a host of other
great news and entertainment, like NPR, CNBC, Fox News, Radio Disney and E! Entertainment Radio. For more
information, visit http://www.sirius.com/.
SIRIUS Satellite Radio legal disclaimer
SIRIUS is available in the U.S. for subscribers with addresses in the continental U.S. and is available in Canada for subscribers with
a Canadian address. To get SIRIUS Satellite Radio, a subscription and compatible tuner and antenna are required (sold separately).
Visit sirius.com for the most complete and up-to-date channel lineup and information.
“SIRIUS” and the SIRIUS dog logo and related marks are trademarks of SIRIUS Satellite Radio Inc.
y
• To ensure optimal reception of the SIRIUS Satellite Radio
Connecting the SiriusConnect
tuner
Connect the SiriusConnect tuner (sold separately) to the
SIRIUS jack on the rear panel of this unit. For details, see
the operating instructions provided with the SiriusConnect
tuner.
™
signals, the antenna of the SiriusConnect tuner must be placed
at or near a window with no obstacles in the path to the sky. The
depending on the area. Refer to the instruction manuals
supplied with the SiriusConnect tuner for the installation of the
antenna.You can mount it indoors or outdoors.
• Use the “ANTENNA INFO” information in the front panel or
“SIRIUS Information” screen in the video monitor (see
page 56) to check the antenna reception level and adjust the
orientation of the antenna.
SiriusConnect tuner and the antenna
(sold separately)
• You will need to connect the SiriusConnect tuner to the AC wall
outlet.
Notes
• If “CHECK SR TUNER” or “ANTENNA ERROR” appears in
the front panel display, the connection of the SiriusConnect
tuner or antenna is incorrect. In such cases, check the
connection of the SiriusConnect tuner and the antenna (see
page 83).
T
N
A
V
5
C
D
XM
SIRIUS
DTV/CBL
DOCK
ANTENNA
To the AC wall outlet
• If “NOT SUPPORTED” appears in the front panel display, this
unit does not support the connected SiriusConnect tuner.
P
B
Y
B
51 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SIRIUS Satellite Radio™ tuning
Activating SIRIUS Satellite
Basic SIRIUS Satellite Radio
operations
™
Radio
™
subscription
Before using the SIRIUS Satellite feature, you need to
activate your SIRIUS Satellite Radio subscription. To
activate the subscription, you need the Sirius ID, which is
uniquely assigned to the SiriusConnect tuner. Sirius ID is
12-digit number and it appears on the package of the
SiriusConnect tuner, on the label of the SiriusConnect
tuner and when you tune into the SIRIUS Satellite Radio
Channel “0” (see below).
O
K
1
Press INPUT l/ h(or press SIRIUS)
to select “SIRIUS” as the input source.
The cursor on the left of the SIRIUS indicator lights
up in the front panel display and the SIRIUS Satellite
Radio information (such as channel number, channel
name, category, artist name, or song title) for the
currently selected channel appears in the front panel
display.
Lights up
■ Displaying the Sirius ID of your
SiriusConnect tuner
MULTI CH
DVR
V-AUX
DTV/CBL
DVD
MD/CD-R CD
TUNER
XM
SIRIUS
K
Press SIRIUS.
1
2
184 SIRIUS Wea
y
F
T
Press 0 and then ENT to display the
Sirius ID of your SiriusConnect tuner.
“000 Sirius IDxxxxxxxxxxxx” (“xxxxxxxxxxxx”
indicates the 12-digit Sirius ID of your SiriusConnect
tuner) appears in the front panel display.
When you select “SIRIUS” as the input source, this unit
automatically recalls the previously selected channel.
Notes
• The SIRIUS Satellite Radio signals cannot be output at the
AUDIO OUT (REC) jacks.
y
H
A
• When you have not activated your subscription yet, you
To scroll the message again, press INFO (or INFO).
Write the Sirius ID below.
ID:
2
SIRIUS Satellite Radio search modes.
“All Channel Search mode” on page 53.
SIRIUS Satellite Radio online information
Contact for activation
URL: https//activate.siriusradio.com/
Phone: 1-888-539-SIRIUS (1-888-539-7474)
• To select a channel from the preset channels, see
“Preset Search mode” on page 53.
the channel number, see “Direct Number Access
mode” on page 53.
y
• You can set the SIRIUS Satellite Radio preset channels
(see page 54).
• You can display the SIRIUS Satellite Radio information in
the front panel display or in the OSD (see page 56).
52 En
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Preset Search mode
Before performing the following operations, press
Prior to selecting a preset channel in the Preset Search
mode, you must preset SIRIUS channels. For details, see
“Setting the SIRIUS Satellite Radio™ preset channels” on
page 54.
K
SIRIUS.
■ All Channel Search mode
B
M
1
Press SEARCH MODE (or SRCH
B
M
1
Press SEARCH MODE (or SRCH
MODE) repeatedly to select “PRESET
SEARCH”.
MODE) repeatedly to select “ALL CH
SEARCH”.
E
Press PRESET/TUNING/CH l/ h(or
2
D
8
2
Press CATEGORY (or A-E/CAT. l/ h)
repeatedly to change the preset channel
group (A to E).
8
PRESET/CH k/ n) repeatedly to search
for a channel within all channels.
y
•
You can search for a channel quickly by pressing and holding
E
Press PRESET/TUNING/CH l/ h(or
3
E
PRESET/TUNING/CH
l
/
h
8
PRESET/CH k/ n) repeatedly to change
8
(or PRESET/CH
k
/
n).
the preset channel number (1 to 8).
• You can skip channels to the previous or next category by
D
8
pressing CATEGORY (or A-E/CAT. l/ h).
y
You can also select the preset channel number directly by
■ Category Search mode
G
pressing the numeric buttons (1 to 8) ( ).
■ Direct Number Access mode
B
M
1
2
3
Press SEARCH MODE (or SRCH
MODE) repeatedly to select “CAT SEARCH”.
M
1
Press SRCH MODE on the remote control
repeatedly to select “ALL CH SEARCH” or
“CAT SEARCH”.
D
8
Press CATEGORY (or A-E/CAT. l/ h)
repeatedly to change the channel category.
G
Press the numeric buttons ( ) to enter the
desired three-digit channel number.
2
E
Press PRESET/TUNING/CH l/ h(or
PRESET/CH k/ n) repeatedly to search
for a channel within the selected channel
category.
8
For example, to enter the number 123, press the
G
numeric buttons ( ) as shown below.
1
2
3
y
You can search for a channel quickly by pressing and holding
E
8
PRESET/TUNING/CH l/ h(or PRESET/CH k/ n).
y
Note
• To display the SIRIUS Radio ID (SID) number displayed in the
front panel display, select channel “0”.
• To enter a one-digit or two-digit channel number, press the
This unit skips the channels when this unit is All Channel Search
mode or Category Search mode in the following cases (it is not
malfunction of this unit):
– the channel is locked (see page 54).
– the channel is out of service.
G
numeric buttons ( ) on the remote control and then press
T
ENT to confirm the input number.
T
• Instead of pressing ENT to tune into the channel
immediately, you can wait a few seconds until this unit confirms
the entered channel number.
– you do not subscribe to the channel.
G
T
• Pressing a button other than the numeric buttons ( ) or ENT
cancels the Direct Number Access mode procedure.
• If the selected channel is locked, “PIN:____” appears in the
front panel display. Enter the four-digit Parental Lock code
G
T
number by using the numeric buttons ( ) or press ENT to
cancel.
53 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SIRIUS Satellite Radio™ tuning
Before performing the following operations, press
E
Press PRESET/TUNING/CH l/ h
4
K
SIRIUS.
8
(or PRESET/CH k/ n) repeatedly to select
a preset channel number (1 to 8) while the
MEMORY indicator is flashing.
The preset channel number appears in the front panel
Setting the SIRIUS Satellite
Radio preset channels
™
Radio channels (A1 to E8: 8 preset channel numbers in
each of the 5 preset channel groups). You can then recall
any preset channel easily by selecting the preset channel
group and number as described in “Preset Search mode”
on page 53.
Flashes
MEMORY
A1ꢀ023 Hair Na
Currently selected preset channel number
1
Search for a channel you want to set as a
preset channel by using one of the SIRIUS
Satellite Radio search modes.
See “Basic SIRIUS Satellite Radio™ operations” on
page 52 for details.
F
9
5
Press MEMORY (or MEMORY) to set
the selected SIRIUS Satellite Radio channel
as a preset channel while the MEMORY
indicator is flashing.
A colon (:) appears next to the preset channel number
for confirmation, and the MEMORY indicator turns
off in the front panel display.
001 SIRIUS Hit
Currently selected channel number
A1:023 Hair Na
Colon (:)
F
9
2
Press MEMORY (or MEMORY).
The MEMORY indicator flashes in the front panel
display for approximately 30 seconds.
Note
Once you set a new preset channel, the one previously stored in
the same preset channel group and number is cleared.
MEMORY
Setting the Parental Lock
Flashes
You can use the Parental Lock feature to limit the access
to the desired SIRIUS Satellite channels. This unit
automatically skips the locked channels when this unit is
in the All Channel Search mode or Category Search mode
and you search a channel by pressing
Note
You must proceed to and carry out steps 3 through 5 while
the MEMORY indicator is flashing in the front panel
display.
E
PRESET/TUNING/CH l/ h
8
(or PRESET/CH k/ n).
D
8
3
Press CATEGORY (or A-E/CAT. l/ h)
repeatedly to select a preset channel group
(A to E) while the MEMORY indicator is
flashing.
■ Setting the code number and the locked
channels
Use this feature to set the Parental Lock code number
(PIN) and select the channels to be locked.
The preset channel group letter appears in the front
panel display.
Flashes
5
Press AMP on the remote control and then
1
2
M
press MENU to display.
MEMORY
8
Press nto select “MANUAL SETUP” and
8
then press ENTER.
A-ꢀꢀ023 Hair N
Currently selected preset channel group
54 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SIRIUS Satellite Radio™ tuning
Note
8
Press nrepeatedly to select “OPTION
8
MENU” and then press ENTER.
3
4
In the SIRIUS Satellite Radio channel list screen, this unit
outputs the sound of the selected channel even if the channel
is locked. Only the first eight characters of each channel
name are displayed in the list.
8
Press k/ nrepeatedly to select “G)SIRIUS
8
SET” and then press ENTER.
The following menu screen appears.
8
10 Press ENTER to lock the selected
channel.
3 OPTION MENU
Check mark appears before the selected channel.
G)SIRIUS SET
. PARENTAL LOCK
y
8
When you select the locked channel and press ENTER,
this unit unlocks the selected channel.
[ ]/[ ]:Up/Down
[p]/[[]:Select
11 Repeat steps 9 and 10 to lock the channels
you want.
8
Press ENTER.
“NEW PIN:0000” appears.
5
9
12 Press RETURN repeatedly to exit from the
PARENTAL LOCK
“PARENTAL LOCK” screen.
-
NEWꢀPIN:0000
M
13 Press MENU to exit from the setup menu.
This unit is tuned into the last channel you select in
the “PARENTAL LOCK” screen. If the channel is
locked, this unit is tuned into “184 SIRIUS Weather
& Emergency” or “000 Sirius IDxxxxxxxxxxxx”
(“xxxxxxxxxxxx” indicates the Sirius ID of your
SiriusConnect tuner).
[0] [9]:NUMBER
[ENT]:ENTER
Note
If a SiriusConnect tuner is not connected to this unit, “Not
Available” appears.
y
If you forget or want to change the Parental lock code number,
use “SSR PIN” in “ADVANCED SETUP” to reset the Parental
Lock code number.
y
If the Parental Lock code number is already set, “PIN:___”
appears instead of “NEW PIN:0000”. Refer to step 8 and
then proceed the operations.
■ Tuning into the locked channels
You can tune into the locked channels by the Direct
number access mode or preset channel mode. When you
tune into the locked channel, following message appears
in the front panel display. Enter the code number you set
for the Parental Lock feature by using the numeric buttons
6
Enter the desired 4-digit code number by
G
using the numeric buttons ( ).
y
9
Press RETURN to return the previous menu level
G
T
(
) or press ENT to cancel the tuning.
without setting the code number.
8
Press ENTER to confirm the code number.
7
8
“OK” appears and then “PIN:___” appears.
____
PIN:
Enter the 4-digit code number you set at step
6 above to unlock the protection.
Note
When the code number is correct, “OK” and then the
SIRIUS Satellite Radio channel list appears.
If the entered code number is incorrect, “Wrong” appears in the
front panel display and this unit is tuned into the previously
selected channel.
8
Press l/ hrepeatedly to select the
desired channel category and then press
9
8
k/ nrepeatedly to select the channel you
want to lock.
55 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SIRIUS Satellite Radio™ tuning
y
Before performing the following operations, press
• The front panel display can indicate up to 14 alphanumeric
characters at once. You can set whether to display the SIRIUS
Satellite Radio information in the front panel display in a
continuous manner or by 14 alphanumeric characters at once by
using the “FL SCROLL” parameter in “OPTION MENU” (see
page 70).
• If the SIRIUS Satellite Radio information contains a character
that cannot be recognized by this unit, the character will be
displayed with a space.
K
SIRIUS.
Displaying the SIRIUS Satellite
Radio™ information
You can display the SIRIUS Satellite Radio information
(such as channel number, channel name, category, artist
name, composer name, or song title) for the currently
• To hold the current SIRIUS Satellite Radio information, press
8
ENTER while it is being displayed.
■ Displaying the SIRIUS Satellite Radio
Note
information in the OSD
If a status message or an error message appears in the front panel
display or in the OSD, see the “SIRIUS Satellite Radio” section
in “Troubleshooting” on page 83 for appropriate remedies.
H
O
Press INFO (or DISPLAY).
The following screen is displayed in the OSD.
■ Displaying the SIRIUS Satellite Radio
[5]
SIRIUSꢀInformationꢀANT:
information in the front panel display
[1]
[2]
ALLꢀCHꢀSEARCH
H
A
Press INFO (or INFO) repeatedly to toggle
between the following SIRIUS Satellite Radio
information display modes.
[6]
[7]
008:Bigꢀ'80s
:Pop
:Sanumemo
[3]
[4]
:RoadꢀtoꢀIndia
e.g.) 008 Big '80s
CHANNEL INFO
C:FrankieꢀZipper
Channel number/name
[1] Search mode (see page 52)
[2] Channel category
[3] Song title
e.g.) Pop
CATEGORY INFO
Channel category
[4] Composer name
[5] Antenna reception level
[6] Channel number/name
[7] Artist name
e.g.) Sanumemo / Roa
e.g.) Frankie Zipper
SONG INFO
Artist name / Song title
y
COMPOSER INFO
O
• To turn off the OSD, press DISPLAY again.
• SIRIUS status messages also appear in the OSD.
Composer name
• You can select the amount of time the SIRIUS Satellite Radio
information is displayed in the OSD by using the
“OSD-SOURCE” parameter in “OPTION MENU” (see
page 70).
ANTENNA INFO
e.g.) 043
ANTENNA
-
• To hold the SIRIUS Satellite Radio information, press
Channel number/Antenna reception level
8
ENTER while it is being displayed in the OSD. While this
unit is holding the information screen, “HOLD” appears in the
OSD.
• The HOLD indicator flashes in the front panel display while
e.g.) 5ch Enhancer
DSP PROG. INFO
8
you are holding the SIRIUS information. Press ENTER
again or change the SIRIUS Satellite Radio channel to release
the held information. When an information is unavailable,
“––––” appears.
Sound field program
Back to “CHANNEL INFO”
56 En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING IPOD™
Once you have stationed your iPod in a Yamaha iPod universal dock (such as YDS-10, sold separately) connected to the
DOCK terminal of this unit (see page 19), you can enjoy playback of your iPod using the supplied remote control. You
can also use the Compressed Music Enhancer mode of this unit to improve the sound quality of the compression artifacts
(such as the MP3 format) stored on your iPod (see page 19).
Notes
• Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.
• Some features may not be compatible depending on the model or the software version of your iPod.
y
• For a complete list of status messages that appear in the front panel display and in the OSD, see the “iPod” section in
“Troubleshooting” on page 85.
• Once your iPod is stationed in a Yamaha iPod universal dock, this unit begins signal transmission with your iPod.
• Once the connection between your iPod and this unit is complete, “iPod connected” appears in the front panel display and the DOCK
indicator lights up in the front panel display.
• Only the analog audio and video signals of your iPod are input at the DOCK terminal, and the analog audio signals can be output at the
analog AUDIO OUT (REC) jacks for recording.
• Your iPod battery is automatically charged when your iPod is stationed in a Yamaha iPod universal dock connected to the DOCK
terminal of this unit as long as this unit is turned on.
Controlling iPod™
You can control your iPod when “V-AUX” is selected as the input source. The operations of your iPod can be done with
the aid of the OSD of this unit (menu browse mode) or without it (simple remote mode).
■ Remote control operation
■ Controlling iPod in the simple remote
mode
You can perform the basic operations of your iPod (play,
stop, skip, etc.) using the supplied remote control without
the aid of the OSD of this unit.
Before performing the following operations, press
4
V-AUX/DOCK.
Button
Function
y
8
ENTER
Subsequent menu
Menu up
• You can view the photos or video clips stored on your iPod
(some models only).
k
• Operations can be also done with the controls on your iPod.
n
Menu down
l
h
Previous menu
Subsequent menu
0 ll
hh
b
a
e
Search backward (Press and hold)
Search forward (Press and hold)
Skip backward
Skip forward
Pause (Menu browse mode)
Play/Pause (Simple remote mode)
p
Play (Menu browse mode)
Play/Pause (Simple remote mode)
M
O
MENU
DISPLAY
Previous menu
Display
57 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Using iPod™
Shuffle Shuffle
Use this feature to set this unit to play songs or albums in
random order.
■ Controlling iPod in the menu browse
mode
You can perform the advanced operations of your iPod
using the supplied remote control when you connect this
unit and a monitor using the VIDEO connection. You can
browse the songs stored on your iPod in the OSD. Further,
you can change or adjust settings for your iPod to suit
your personal preferences.
Choices: Off, Songs, Albums
•
•
Select “Off” to deactivate this feature.
Select “Songs” to set this unit to play songs in random
order.
•
Select “Albums” to set this unit to play albums in
random order.
y
• The name of the song being played also appears in the front
panel display according to the “FL SCROLL” parameter in
“OPTION MENU” (see page 70).
y
When “Shuffle” is set to a setting other than “Off”, “
in the top right corner while songs or albums are being shuffled.
” appears
• You can select the amount of time the iPod menu and play
information is displayed in the OSD by using the
“OSD-SOURCE” in “OPTION MENU” (see page 70)
Repeat Repeat
Use this feature to set this unit to repeat one song or a
sequence of songs.
Choices: Off, One, All
Notes
•
•
•
Select “Off” to deactivate this feature.
Select “One” to set this unit to repeat one song.
Select “All” to set this unit to repeat a sequence of
songs.
• Operations cannot be done with the controls on your iPod.
• The Yamaha logo appears in the display window of your iPod.
• There are some characters that cannot be displayed in the front
panel display or in the OSD of this unit. Those characters are
replaced with underscores “_”.
y
• The “Settings” parameters can be changed or adjusted only in
When “Repeat” is set to a setting other than “Off”, “ ” or “
”
1
All
8
the OSD. Press ENTER repeatedly to toggle between the
appears in the top right corner while one song or a sequence of
songs are being repeated.
“Settings” parameter settings.
• You cannot browse the photos or video clips stored on your
iPod in the OSD. Use the simple remote mode to enjoy
watching the photos or video clips stored on your iPod.
■ The function of the play information
display
4
Press V-AUX/DOCK and then
1
2
[1]
[7]
[8]
ODISPLAY
.
iPodꢀꢀꢀꢀꢀ[Play]ꢀꢀꢀꢀ
All
The following display appears in the OSD.
[2]
[3]
[4]
ꢀ1ꢀ/ꢀ9ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀFrankieꢀZipperꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀMade-to-orderꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀRoadꢀtoꢀIndiaꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ
ꢀꢀ||;;;;;;;;;;;;;;;;;;ꢀꢀ
ꢀꢀ0:51ꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀꢀ-7:44ꢀꢀ
iPod
Top
[9]
Playlists
Artists
Albums
Songs
Genres
>
>
>
>
>
>
>
[5]
[6]
Composers
Settings
[10]
[1] Playback status
[2] Track number/total tracks
[3] Artist name
8
Press k/ n / l/ hto navigate the iPod
8
menu and then press ENTER to begin
playback of the selected song.
Choices: Playlists (playlists), Artists (artists), Albums
(albums), Songs (songs), Genres (genres),
Composers (composers), Settings (settings)
• Playlists > Songs
[4] Song title
[5] Progress bar
• Artists > Albums > Songs
• Albums > Songs
• Songs
[6] Elapsed time
[7] Shuffle and repeat icons
• Genres > Artists > Albums > Songs
• Composers > Albums > Songs
• Settings > Shuffle, Repeat
[8]
(playback),
(pausing),
(search
forward) and
(search backward)
[9] Name of the album
[10] Remaining time
58 En
Download from Www.Somanuals.com. All Manuals Search And Download.
USING BLUETOOTH™ COMPONENTS
Using Bluetooth™ components
You can connect a Yamaha Bluetooth adapter (such as YBA-10, sold separately) to the DOCK terminal of this unit and
enjoy the music contents stored in your Bluetooth component (such as a portable music player) without wiring between
this unit and the Bluetooth component. You need to perform “pairing” the connected Bluetooth adapter and your
Bluetooth component in advance.
Note
Pairing the Bluetooth™ adapter
and your Bluetooth component
If the Bluetooth adapter is not connected to the DOCK
terminal of this unit, “No BT adapter” appears in the front
panel display.
Pairing must be performed when using a Bluetooth
component with the Bluetooth adapter connected to this
unit for the first time or if the pairing data has been
deleted. “Pairing” refers to the operation of registering a
Bluetooth component for Bluetooth communications.
4
5
Check that the Bluetooth component detects
the Bluetooth adapter.
If the Bluetooth component detects the Bluetooth
adapter, “YBA-10 YAMAHA” (example) appears in
the Bluetooth device list.
y
• You only need the pairing operation for the first time that you
use the Bluetooth component with the Bluetooth adapter.
• Pairing requires operations on this unit and on the other
component with which Bluetooth communications are to be
established. If necessary, refer to the other component’s
operating instructions.
Select the Bluetooth adapter in the Bluetooth
device list and then enter the pass key
“0000” on the Bluetooth component.
When the pairing procedure is successful,
There are two pairing methods: pairing by using “START
“Completed” appears in the front panel display.
Note
■ Pairing by using “SET MENU”
Use this feature to perform pairing with the video monitor.
Select “START PAIRING” in “INPUT MENU”. See
page 71 for details.
The Yamaha Bluetooth adapter can be paired with up to eight
Bluetooth components. When pairing is conducted successfully
with a ninth component and the pairing data is registered, the
pairing data for the least recently used other component is
cleared.
■ Quick pairing
Playback of the Bluetooth™
component
To ensure security, a time limit of 8 minutes is set for the
pairing operation. You are recommended to read and fully
understand all the instructions before starting.
OINPUT l
/ hrepeatedly (or press
V-AUX/DOCK) to select “V-AUX” as the
input source.
1
Press
4
OINPUT l
/ hrepeatedly (or press
V-AUX/DOCK) to select “V-AUX” as the
input source.
1
Press
4
2
Start playback of your Bluetooth component.
When the connected Bluetooth adapter detects the
Bluetooth component, “BT connected” and the
DOCK indicator appears in the front panel display.
2
3
Turn on the Bluetooth component you want
to pair with.
y
CBAND
7
(or BAND) for 3
Press and hold
seconds to start pairing.
8
• When you press ENTER, the connected Bluetooth adapter
searches and connect to the last connected Bluetooth
Once the Bluetooth adapter starts pairing,
“Searching...” appears for a moment. While the
Bluetooth adapter is in the pairing mode, DOCK
indicator flashes in the front panel display.
component. If the Bluetooth adapter cannot find the Bluetooth
component, “Not found” appears in the front panel display.
• To disconnect the Bluetooth adapter from the Bluetooth
9
component, press RETURN.
y
CBAND
7
(or BAND) again.
To cancel the pairing, press
59 En
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING
Recording
Recording adjustments and other operations are performed from the recording components. Refer to the operating
instructions for those components.
Notes
• When this unit is set to the standby mode, you cannot record between other components connected to this unit.
• TONE CONTROL (see page 41) and VOLUME settings, speaker levels (see page 41) and the sound field programs (see page 38) do
not affect recorded material.
• The source connected to the MULTI CH INPUT jacks of this unit cannot be recorded.
• The XM Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks.
• The SIRIUS Satellite Radio signals cannot be output at the AUDIO OUT (REC) jacks.
• Digital signals input at the DIGITAL INPUT jacks are not output at the analog AUDIO OUT (REC) jacks for recording. Therefore, if
your source component is connected to provide only digital signals, you cannot record the source.
• A given input source is not output on the same OUT (REC) channel.
• The analog audio signals input at the DOCK terminal can be output at the analog AUDIO OUT (REC) jacks for recording.
• Once you have connected a recording component to this unit, keep the component turned on while using this unit. If the component is
turned off, this unit may distort the sound from other components.
• Check the copyright laws in your country to record from CDs, radio, etc. Recording of copyrighted material may infringe copyright
laws.
y
Do a test recording before you start an actual recording.
If you play back a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture
itself may be disturbed due to those signals.
1
2
Turn on all the connected components.
3
4
Start playback on the selected source
component or select a broadcast station.
O
Press INPUT l/ hrepeatedly (or press
one of the input selector buttons (4)) to
select the source component you want to
record from.
Start recording on the recording component.
60 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
SET MENU
You can use the following parameters in “SET MENU” to adjust a variety of system settings and customize the way this
unit operates. Change the initial settings (indicated in bold under each parameter) to reflect the needs of your listening
environment.
■ Auto setup AUTO SETUP
Use this feature to automatically adjust speaker and system parameters (see page 24).
■ Manual setup MANUAL SETUP
Use this feature to manually adjust speaker and system parameters.
Sound menu 1 SOUND MENU
Parameter
Features
Page
Selects the size of each speaker, the speakers for low-frequency signal output, and the
crossover frequency, and the location of the front speakers connected to the FRONT B
terminals.
A)SPEAKER SET
63
Adjusts the output level of each speaker.
65
65
66
66
66
66
B)SP LEVEL
Adjusts the delay time of each speaker.
C)SP DISTANCE
D)CENTER GEQ
E)LFE LEVEL
F)DYNAMIC RANGE
G)AUDIO SET
Adjusts the tonal quality of the center speaker.
Adjusts the output level of the LFE channel for Dolby Digital or DTS signals.
Adjusts the dynamic range of Dolby Digital or DTS signals.
Adjusts the muting level, audio delay, maximum volume level and initial volume level.
Selects whether to play back HDMI audio signals on this unit or on another HDMI
component connected to the HDMI OUT jack.
H)HDMI SET
67
Input menu 2 INPUT MENU
Parameter
Features
Assigns the input jacks of this unit according to the component to be used.
Changes the name of the input source.
Page
68
A)INPUT ASSIGNMENT
B)INPUT RENAME
C)VOLUME TRIM
68
Adjusts the output volume of each input source.
69
Selects the decoder mode for the sources connected to the DIGITAL INPUT jacks on the
rear panel of this unit.
69
69
D)DECODER MODE
E)MULTI CH SET
Selects the video source played in the background of the sources input from the MULTI CH
INPUT jacks.
61 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
Option menu 3 OPTION MENU
Parameter
Features
Page
70
Adjusts the brightness of the front panel display and the way in which the XM and iPod
information is displayed.
A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI
Locks sound field program parameters and other “SET MENU” settings.
70
DIGITAL INPUT jacks when you turn on the power of this unit.
71
Initializes the parameters of a group of sound field programs.
71
Bluetooth component (see page 59).
E)BLUETOOTH SET
F)XM RADIO SET
G)SIRIUS SET
71
Displays the current reception level of the XM Satellite Radio signals.
72
Sets the SIRIUS Parental Lock code number and the channel lock configuration (see
page 54).
72
Note
The “XM RADIO SET” and “SIRIUS SET” parameters are only applicable to the U.S.A. and Canada models.
■ Signal information SIGNAL INFO
Use this feature to check audio signal information (see page 36).
Using SET MENU
Use the remote control to access and adjust each
parameter.
8
3
Press ENTER to enter “MANUAL SETUP”.
The “MANUAL SETUP” display appears in the
OSD.
y
;MANUAL SETUP
You can change the “SET MENU” parameters while this unit is
. 1 SOUND MENU
2 INPUT MENU
3 OPTION MENU
reproducing sound.
5
M
1
Press AMP and then press MENU to
enter “SET MENU”.
[ ]/[ ]:Up/Down
[ENTER]:Enter
The top “SET MENU” display appears in the OSD.
8
8
4
5
Press k/ n/ l/ hand ENTER to select
SET MENU
TOPAMENU
and change the parameter.
8
• Press k/ nto select the desired menu or
. ;AUTO SETUP
.A;MANUAL SETUP
;SIGNAL INFO
parameter.
8
• Press l/ hto change the parameter value.
[ ]/[ ]:Up/Down
[ENTER]:Enter
8
• Press ENTER to enter the selected menu or to
confirm the parameter.
9
• Press RETURN to return to the previous menu
8
Press k/ nto select “MANUAL SETUP”.
2
level.
M
Press MENU to exit from “SET MENU”.
SET MENU
TOPAMENU
;AUTO SETUP
.A;MANUAL SETUP
;SIGNAL INFO
[ ]/[ ]:Up/Down
[ENTER]:Enter
62 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
Woofer section of a speaker is 16 cm (6.5 in) or larger:
large
1 SOUND MENU
Use this menu to manually adjust any speaker settings or
compensate for video signal processing delays when using
LCD monitors or projectors.
Woofer section of a speaker is smaller than 16 cm
(6.5 in): small
Front speakers FRONT SP
Choices: SMALL, LARGE
;MANUAL SETUP
1 SOUND MENU
;MANUAL SETUP
1 SOUND MENU
1/2
2/2
. A)SPEAKER SET
B)SP LEVEL
C)SP DISTANCE
D)CENTER GEQ
E)LFE LEVEL
[ ]/[ ]:Up/Down
[ENTER]:Enter
. F)DYNAMIC RANGE
G)AUDIO SET
H)HDMI SET
1 SOUND MENU
A)SPEAKER SET
FRONT SP
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Speaker settings A)SPEAKER SET
Use this feature to manually adjust any speaker settings.
SMALL >LARGE
FRONT B speaker setting FRONT B
Use this feature to select the location of the front speakers
connected to the FRONT B terminals.
Choices: FRONT, ZONE B
When the front speakers are large
Select “LARGE” (large).
When the front speakers are small
Select “SMALL” (small).
1 SOUND MENU
Note
A)SPEAKER SET
When “LFE/BASS OUT” is set to “FRONT” (see page 64), you
can select only “LARGE” in “FRONT SP”. If the value of
“FRONT SP” is set to a setting other than “LARGE” in advance,
this unit automatically changes the value to “LARGE”.
FRONT B;;;;FRONT
[ ]/[ ]:Up/Down
[ ]/[ ]:Select
p
[
Center speaker CENTER SP
Choices: NONE, SML, LRG
•
•
Select “FRONT” to turn on or off SPEAKERS A and B
when the speakers connected to the FRONT B
terminals are set in the main zone.
Select “ZONE B” if the speakers connected to the
FRONT B terminals are set in another zone. If
SPEAKERS A is turned off and SPEAKERS B is
turned on, all the speakers including the subwoofer in
the main zone are muted and this unit outputs sound at
the FRONT B terminals only.
1 SOUND MENU
A)SPEAKER SET
CENTER SP
NONE >SML LRG
Notes
When the center speaker is large
Select “LRG” (large).
• If you connect headphones to the PHONES jack of this unit, the
sound is output from both headphones and the FRONT B
terminals when “FRONT B” is set to “ZONE B”.
• If a DSP program is selected when “FRONT B” is set to
“ZONE B”, this unit automatically enters the Virtual CINEMA
DSP mode (see page 39).
When the center speaker is small
Select “SML” (small).
When you do not use the center speaker
Select “NONE” (none). The center channel signals are
directed to the front left and right speakers.
63 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
Surround left/right speakers SUR. L/R SP
Choices: NONE, SML, LRG
Crossover CROSSOVER
speakers set to “SML” (or “SMALL”) in “SPEAKER
SET” (see page 63). All frequencies below the selected
frequency will be sent to the subwoofer or front speakers
depending on the setting of “LFE/BASS OUT” in
“SPEAKER SET” (see page 63).
1 SOUND MENU
A)SPEAKER SET
SUR. L/R SP
Choices: 40Hz, 60Hz, 80Hz, 90Hz, 100Hz, 110Hz,
120Hz, 160Hz, 200Hz
NONE >SML LRG
1 SOUND MENU
When the surround speakers are large
Select “LRG” (large).
A)SPEAKER SET
CROSSOVER
When the surround speakers are small
Select “SML” (small).
FREQ;;;80Hz
When you do not use the surround speakers
Select “NONE” (none). This unit is set to the Virtual
CINEMA DSP mode (see page 39).
Subwoofer phase SUBWOOFER PHASE
Use this feature to switch the phase of your subwoofer if
bass sounds are lacking or unclear.
Choices: NORMAL, REVERSE
LFE Bass out LFE/BASS OUT
Use this feature to select the speakers that output the LFE
(low-frequency effect) and the low-frequency signals.
Choices: SWFR, FRNT, BOTH
1 SOUND MENU
A)SPEAKER SET
SUBWOOFER PHASE
1 SOUND MENU
A)SPEAKER SET
LFE/BASS OUT
>NORMAL REVERSE
•
•
Select “NORMAL” if you do not want to reverse the
phase of your subwoofer.
Select “REVERSE” to reverse the phase of your
subwoofer.
SWFR FRNT>BOTH
When a subwoofer is connected to this unit
and you want to get natural bass sound
Select “SWFR” (subwoofer). The LFE signals as well
as the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are directed to the subwoofer.
When a subwoofer is connected to this unit
and you want to get rich bass sound
Select “BOTH” (both). The low-frequency signals of
any source are output from the subwoofer. The LFE
signals as well as the low-frequency signals of other
speakers set to “SML” (or “SMALL”) are directed to
the subwoofer. The low-frequency signals of the front
left and right channels are directed to the front left and
right speakers and the subwoofer regardless of the
“FRONT SP” setting (see page 63).
When you do not use a subwoofer
Select “FRNT” (front). The LFE signals, the low-
frequency signals of the front left and right channels,
and the low-frequency signals of other speakers set to
“SML” (or “SMALL”) are all directed to the front left
and right speakers regardless of the “FRONT SP”
setting (see page 63).
64 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
■ Speaker level B)SP LEVEL
Use this feature to manually adjust the output level of each
speaker.
Control range: –10 to +10 dB
Control step: 1 dB
■ Speaker distance C)SP DISTANCE
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
Initial setting: 0 dB
1 SOUND MENU
B)SP LEVEL
-
. FR.L
FR.R
1 SOUND MENU
B)SP LEVEL
-
.SUR.L
SUR.R
1/2
2/2
__________
__________
+
+
1 SOUND MENU
C)SP DISTANCE
1 SOUND MENU
C)SP DISTANCE
CNTR
SWFR
1/2
2/2
. UNIT;;;;;;;;feet
FRONT L;;;10.0ft
FRONT R;;;10.0ft
CENTER;;;;;8.5ft
SWFR;;;;;;10.0ft
[ ]/[ ]:Up/Down
. SUR. L;;;;;8.0ft
SUR. R;;;;;8.0ft
[ ]/[ ]:Up/Down
[ ]/[ ]:Adjust
[ ]/[ ]:Adjust
p
[
p
[
SP LEVEL
Adjusted speaker
Front left speaker
FR.L
Unit UNIT
Choices: meters (m), feet (ft)
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
Front right speaker
Center speaker
FR.R
CNTR
SWFR
SUR.L
SUR.R
Subwoofer
•
•
Select “meters” to adjust speaker distances in meters.
Select “feet” to adjust speaker distances in feet.
Surround left speaker
Surround right speaker
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5 ft)
Note
The available speaker channels differ depending on the setting of
the speakers.
SUR. L/SUR. R: 2.40 m (8.0 ft)
SP DISTANCE
FRONT L
FRONT R
CENTER
SWFR
Adjusted speaker
Front left speaker
Front right speaker
Center speaker
Subwoofer
Surround left speaker
Surround right speaker
SUR. L
SUR. R
Note
The available speaker channels differ depending on the setting of
the speakers.
65 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
■ Center speaker equalizer D)CENTER GEQ
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, 1kHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
■ Dynamic range F)DYNAMIC RANGE
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
1 SOUND MENU
Control range: –6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
F)DYNAMIC RANGE
. SPEAKER;;;;;;MAX
HEADPHONE;;;;MAX
[ ]/[ ]:Up/Down
[ ]/[ ]:Adjust
1 SOUND MENU
p
[
D)CENTER GEQ
TEST >OFF ON
. 100Hz ;;;;;;
300Hz ;;;;;;
1kHz ;;;;;;
0dB
0dB
0dB
0dB
0dB
Speaker SPEAKER
Adjusts the speaker compression.
3kHz ;;;;;;
10kHz ;;;;;;
[ ]/[ ]:Up/Down
[ ]/[ ]:Adjust
p
[
Headphone HEADPHONE
Adjusts the headphone compression.
Test tone TEST
Use this feature to make adjustments for “CENTER GEQ”
while listening to a test tone.
Choices: MIN, STD, MAX
•
Select “MIN” (minimum) if you regularly listen at low
volume levels.
Choices: OFF, ON
•
•
Select “STD” (standard) for general use.
Select “MAX” (maximum) to preserve the greatest
amount of dynamic range.
•
Select “OFF” to stop test tones and output the currently
selected source component.
•
Select “ON” to output test tones from the center and
front left speakers.
■ Audio settings G)AUDIO SET
Use this feature to adjust the overall audio settings of this
unit.
■ Low-frequency effect level E)LFE LEVEL
Use this feature to adjust the output level of the LFE (low-
frequency effect) channel according to the capacity of
your subwoofer or headphones. The LFE channel carries
low-frequency special effects which are only added to
certain scenes. This setting is effective when the input
signal contains the LFE channel.
1 SOUND MENU
G)AUDIO SET
. MUTE TYPE;;;FULL
A.DELAY;;;;;;0ms
MAX VOL.;;;+16dB
INIT.VOL.;;;;OFF
Control range: –20 to 0 dB
Control step: 1 dB
[ ]/[ ]:Up/Down
[ ]/[ ]:Select
p
[
Mute type MUTE TYPE
1 SOUND MENU
E)LFE LEVEL
Use this feature to adjust how much the mute function
reduces the output volume (see page 35).
Choices: FULL, –20dB
. SPEAKER;;;;;;0dB
HEADPHONE;;;;0dB
•
Select “FULL” to completely mute all the audio
output.
[ ]/[ ]:Up/Down
[ ]/[ ]:Adjust
p
[
•
Select “–20dB” to reduce the current volume by 20 dB.
Audio delay A.DELAY
Speaker SPEAKER
Use this feature to delay the sound output and synchronize
it with the video image. This may be necessary when
using certain LCD monitors or projectors.
Control range: 0 to 160 ms
Adjusts the speaker LFE level.
Headphone HEADPHONE
Adjusts the headphone LFE level.
Control step: 1 ms
Note
Depending on the settings of “LFE/BASS OUT” (see page 64),
some signals may not be output at the SUBWOOFER OUTPUT
jack.
66 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
Maximum volume MAX VOL.
■ HDMI set H)HDMI SET
Use this feature to set the maximum volume level. This
feature is useful to avoid the unexpected loud sound by
mistake. For example, the original volume range is +16 dB
to –80 dB. However, when “MAX VOL.” is set to –5 dB,
the volume range becomes –5 dB to –80 dB.
Use this feature to select the component to play back
HDMI audio signals.
1 SOUND MENU
H)HDMI SET
Control range: +16 dB, +10 dB to –30 dB
Control step: 5 dB
SUPPORT AUDIO:
HTR-6140
[ ]/[ ]:Select
p
[
[ENTER]:Return
Note
The “MAX VOL.” setting takes priority over the “Initial Volume”
setting. For example, if “INIT.VOL.” is set to –20 dB and “MAX
VOL.” is set to –30 dB, the volume level is automatically set to
–30 dB when you turn on the power of this unit next time.
Support audio S.AUDIO
Use this feature to select whether to play back HDMI
audio signals on this unit or on another HDMI component
connected to the HDMI OUT jack on the rear panel of this
unit.
Initial volume INIT.VOL.
Use this feature to set the volume level when the power of
this unit is turned on.
Choices: Off, MUTE, –80 dB to +16 dB
Control step: 1 dB
Choice
Functions
Plays back HDMI audio signals on this unit. The
HDMI audio signals input at the HDMI input
jacks of this unit are not output to the HDMI
component connected to the HDMI OUT jack on
the rear panel of this unit.
HTR-6140
Note
The “MAX VOL.” setting takes priority over the “INIT.VOL.”
setting.
Plays back HDMI audio signals on another
HDMI component connected to the HDMI OUT
jack.
Other
Notes
• This unit transmits audio and video signals input at the HDMI
input jacks to the HDMI out jack only when this unit is turned
on even if “SUPPORT AUDIO” is set to “Other”.
• Available audio/video signals depend on the specification of the
connected video monitor. Refer to the instruction manual of
each connected component.
67 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
For HDMI jacks 1 and 2
HDMI IN [1]
2 INPUT MENU
Use this menu to reassign the input jacks, select the
decoder mode or rename the input source.
HDMI IN [2]
Choices: (1) DVD, DTV/CBL, V-AUX, DVR
(2) DVD, DTV/CBL, V-AUX, DVR
;MANUAL SETUP
2 INPUT MENU
2 INPUT MENU
. A)INPUT ASSIGNMENT
B)INPUT RENAME
C)VOLUME TRIM
D)DECODER MODE
E)MULTI CH SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
A)INPUT ASSIGNMENT
HDMI IN
. [IN1];;; DVD
(
DVD
)
[IN2];;;DTV/CBL
(DTV/CBL )
[ ]/[ ]:Select
p
[
■ Input assignment
A)INPUT ASSIGNMENT
■ Input rename B)INPUT RENAME
Use this feature to change the name of the input source
that appears in the OSD and in the front panel display.
Use this feature to assign the input jacks according to the
component to be used if the initial settings of this unit do
not correspond to your needs. Change the following
parameters to reassign the respective jacks and effectively
connect more components.
2 INPUT MENU
B)INPUT RENAME
Once the input jacks are reassigned, you can select the
DVD
-> DVD
OINPUT
corresponding component by using
l/ h(or
4
the input selector buttons ( )).
[ ]/[ ]:Position
p
[ ]/[ ]:Chara.
[
For COAXIAL INPUT jack 1
COAXIAL IN (1)
Choices: (1) CD, MD/CD-R, DVD, DTV/CBL,
4
)
1
Press one of the input selector buttons (
V-AUX, DVR
E
or MULTI CH IN to select the input
source you want to change the name of.
2 INPUT MENU
XM
SIRIUS
A)INPUT ASSIGNMENT
COAXIAL IN
CD
DVD
MD/CD-R TUNER
. (1);;;;; DVD
(
DVD
)
MULTI CH IN
or
DTV/CBL
DVR
[ ]/[ ]:Select
p
[
V-AUX/DOCK
For OPTICAL INPUT jacks 2 and 3
OPTICAL IN (2)
OPTICAL IN (3)
5
8
2
3
Press AMP and then press l/ hon the
remote control to place the “_” (underscore)
under the space or the character you want to
edit.
Choices: (2) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
(3) CD, MD/CD-R, DVD, DTV/CBL,
V-AUX, DVR
8
Press k/ nto select the character you
8
want to use and then press l/ hto move
to the next space.
2 INPUT MENU
A)INPUT ASSIGNMENT
OPTICAL IN
. (2);;;;;DTV/CBL
(DTV/CBL )
(3);;;;;
(
CD
CD
Notes
)
• You can use up to 8 characters for each input.
[ ]/[ ]:Select
p
[
8
• Press nto change the character in the following order,
8
or press kto go in the reverse order:
Note
A to Z, a space, 0 to 9, a space, a to z, a space, symbols (#,
*, –, +, etc.)
You cannot select a specific item more than once.
68 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
DTS decoder prioritize setting
4
5
Repeat steps 1 through 3 to rename each
input source.
Choices: AUTO, DTS
•
Select “AUTO” if you want this unit to automatically
detect input signal types and select the appropriate
input mode.
8
Press ENTER to exit from “INPUT
RENAME”.
•
Select “DTS” when you play back a DTS-CD.
■ Multi channel input setup
E)MULTI CH SET
■ Volume trim C)VOLUME TRIM
Use this feature to adjust the output volume of each
source. This is useful if you want to balance the level of
each input source to avoid sudden changes in volume
when switching between input sources.
Choices: CD, MD/CD-R, TUNER, DVD,
DTV/CBL, V-AUX, DVR, DOCK,
MULTI CH, XM, SIRIUS
2 INPUT MENU
E)MULTI CH SET
BGV;;;;;;;;;LAST
[ ]/[ ]:Select
p
[
Control range: –6.0 to +6.0 dB
Control step: 1.0 dB
Background Video BGV
Initial setting: 0.0 dB
Use this feature to select the video source played in the
background of the sources input at the MULTI CH INPUT
jacks.
2 INPUT MENU
C)VOLUME TRIM
Choices: DVD, DTV/CBL, V-AUX, DVR, LAST
y
DVD
DVD ;;;;;0.0dB
Select “LAST” to set this unit to automatically select the last
selected video source as the background video source.
[ ]/[ ]:Adjust
p
[RETURN]:Exit
[
Note
You can only adjust the value for DOCK when your iPod is
stationed in the Yamaha Universal Dock connected to this unit.
■ Decoder mode D)DECODER MODE
2 INPUT MENU
D)DECODER MODE
.
>AUTO LAST
CD ;;;;AUTO
DVD ;;;;AUTO
DTV/CBL ;;;;AUTO
[ ]/[ ]:Up/Down
[ ]/[ ]:Select
p
[
Decoder select mode
Use this feature to designate the default decoder mode for
the input sources connected to the DIGITAL INPUT jacks
when you turn on the power of this unit.
Choices: AUTO, LAST
•
Select “AUTO” if you want this unit to automatically
detect the type of input signals and select the
appropriate decoder mode.
•
Select “LAST” if you want this unit to automatically
select the last decoder mode used the connected input
source.
69 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
Source feature OSD display time
OSD-SOURCE
3 OPTION MENU
Use this menu to adjust the optional system parameters.
Use this feature to set the amount of time to display the
XM Satellite Radio information, SIRIUS Satellite Radio
information or iPod menu in the OSD after you perform a
certain operation.
;MANUAL SETUP
3 OPTION MENU
;MANUAL SETUP
3 OPTION MENU
Choices: ON, 10s, 30s
1/2
2/2
•
•
•
Select “ON” to display the OSD unceasingly during an
operation.
Select “10s” to turn off the OSD 10 seconds after you
perform a certain operation.
Select “30s” to turn off the OSD 30 seconds after you
perform a certain operation.
. A)DISPLAY SET
B)MEMORY GUARD
C)AUDIO SELECT
D)PARAM. INI
E)BLUETOOTH SET
. F)XM RADIO SET
G)SIRIUS SET
[ ]/[ ]:Up/Down
[ENTER]:Enter
[ ]/[ ]:Up/Down
[ENTER]:Enter
■ Display settings A)DISPLAY SET
Amplifier function OSD display time
OSD-AMP
3 OPTION MENU
A)DISPLAY SET
Use this feature to set the amount of time to display the
status after you perform a certain operation.
Choices: ON, 10s, 30s
DIMMER;;;;;;;;;0
FL SCROLL;;;CONT
. OSD SHIFT;;;;;;0
OSD-SOURCE;;;30s
OSD-AMP;;;;;;30s
[ ]/[ ]:Up/Down
•
•
•
Select “ON” to display the OSD constantly during an
operation.
Select “10s” to turn off the OSD 10 seconds after you
perform a certain operation.
Select “30s” to turn off the OSD 30 seconds after you
perform a certain operation.
[ ]/[ ]:Select
p
[
Dimmer DIMMER
Use this feature to adjust the brightness of the front panel
display.
■ Memory guard B)MEMORY GUARD
Use this feature to prevent accidental changes to DSP
program parameter values and other system settings.
Choices: OFF, ON
Control range: –4 to 0
Control step: 1
8
•
•
Press lto make the front panel display dimmer.
8
Press hto make the front panel display brighter.
Front panel display scroll FL SCROLL
Use this feature to set whether to display the information
(such as a song title or a channel name) in the front panel
display in a continuous manner or by the first 14
alphanumeric characters after scrolling all characters once
when “XM”, “SIRIUS” or “DOCK” is selected as the
input source.
3 OPTION MENU
B)MEMORY GUARD
>OFF
ON
[ ]/[ ]:Select
p
[
Choices: CONT, ONCE
•
•
Select “CONT” to display the operation status in the
front panel display in a continuous manner.
Select “ONCE” to display the operation status in the
front panel display by the first 14 alphanumeric
characters after scrolling all characters once.
•
•
Select “OFF” to turn off the “MEMORY GUARD”
feature.
Select “ON” to protect:
– sound field program parameters
– all “SET MENU” items
– all speaker levels
OSD shift OSD SHIFT
– SCENE template parameters
Use this feature to adjust the vertical position of the OSD.
Control range: –5 (downward) to +5 (upward)
Control step: 1
Initial setting: 0
•
•
Note
When “MEMORY GUARD” is set to “ON”, you cannot select
and adjust any other “SET MENU” items.
8
Press lto lower the position of the OSD.
8
Press hto raise the position of the OSD.
70 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
■ Audio select C)AUDIO SELECT
Use this feature to designate the default audio input jack
select setting for the input sources when you turn on the
power of this unit.
■ Bluetooth setting E)BLUETOOTH SET
3 OPTION MENU
E)BLUETOOTH SET
Choices: AUTO, LAST
START PAIRING
3 OPTION MENU
C)AUDIO SELECT
>AUTO LAST
[ENTER]:Enter
Use this feature to start pairing the connected Yamaha
Bluetooth adapter (such as YBA-10, sold separately) with
your Bluetooth component. For details about the pairing,
refer to “Pairing the Bluetooth™ adapter and your
Bluetooth component” on page 59.
[ ]/[ ]:Select
[
p
•
•
detect the type of input signals and select the
appropriate input mode.
Select “LAST” if you want this unit to automatically
select the last input mode used for the connected input
source (see page 34).
To ensure security, a time limit of 8 minutes is set for
the pairing operation. You are recommended to read
and fully understand all the instructions before starting.
■ Parameter initialization D)PARAM. INI
Use this feature to set all the parameters of the sound field
programs to the initial factory settings.
Choices: NO, YES
8
1
2
Press ENTER to start pairing.
The connected Bluetooth adapter starts searching
Bluetooth components. “Searching...” appears in the
video monitor.
Check that the Bluetooth component detects
the Bluetooth adapter.
3 OPTION MENU
D)PARAM. INI
If the Bluetooth component the Bluetooth adapter,
“YBA-10 YAMAHA” (example) appears in the
Bluetooth device list.
>NO
YES
[ ]/[ ]:Select
p
[
[ENTER]:Return
3
Select the Bluetooth adapter in the Bluetooth
device list and then enter the pass key
“0000” on the Bluetooth component.
Once this unit completes the pairing successfully,
“Pairing completed” appears.
•
•
Select “NO” to cancel the parameter initialization and
return to the previous menu screen.
8
Select “YES” and press ENTER to set all the sound
field parameters to the initial factory settings.
Notes
y
9
To cancel the pairing, press RETURN to exit from
“START PAIRING”.
• You cannot automatically revert to the previous parameter
settings once you initialize the sound field program parameters.
• You cannot separately initialize individual sound field
programs.
• You cannot initialize any sound field program groups when
“MEMORY GUARD” is set to “ON”.
9
Press RETURN to exit from “START
4
PAIRING”.
Notes
• If the connected Bluetooth adapter cannot find any Bluetooth
components, “Not found” appears.
• If a Bluetooth adapter is not connected to this unit, “No
Bluetooth Adapter” appears.
71 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SET MENU
■ XM Radio setting F)XM RADIO SET
(U.S.A. and Canada models only)
3 OPTION MENU
F)XM RADIO SET
XM ANTENNA;;;95%
[ENTER]:Return
XM Radio antenna XM ANTENNA
Use this feature to check the current reception level of the
XM Satellite Radio signals. For the best reception, orient
XM Mini-Tuner so that a value of 60% or more is
displayed here.
Display status: NONE, 0 to 100%
Note
“NONE” is displayed if XM Mini-Tuner Dock is not connected to
this unit. In this case, check the antenna connections (see
page 46).
G)SIRIUS SET
(U.S.A. and Canada models only)
Use this feature to set the code number for locking the
desired SIRIUS Satellite Radio channels. Refer to “Setting
the Parental Lock” on page 54 for details.
3 OPTION MENU
G)SIRIUS SET
. PARENTAL LOCK
[ ]/[ ]:Up/Down
[ENTER]:Select
SIRIUS Satellite Radio parental lock
PARENTAL LOCK
Use this feature to set the code number for locking the
desired SIRIUS Satellite Radio channels. Refer to “Setting
the Parental Lock” on page 54 for details.
72 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control features
In addition to controlling this unit, the remote control can also operate other audiovisual components made by Yamaha
and other manufacturers. To control your TV or other components, you must set up the appropriate remote control code
for each input source (see page 75).
Controlling this unit, a TV, or other components
■ Controlling this unit
Press AMP to control this unit.
■ Controlling a TV
Press DTV/CBL to control your TV. To control your
5
4
TV, you must set the appropriate remote control code for
DTV/CBL (see page 75).
POWER POWER
STANDBY
SIRIUS
POWER
MUTE
TV
AV
A
XM
POWER POWER
STANDBY
SIRIUS
POWER
MUTE
TV
AV
CD
DVD
MD/CD-R TUNER
A
XM
TV CH
DTV/CBL
B
DVR
C
CD
DVD
MD/CD-R TUNER
V-AUX/DOCK
AMP
TV CH
DTV/CBL
B
DVR
C
*1
*1
TV VOL
TV INPUT
TV MUTE
DTV/CBL
V-AUX/DOCK
AMP
AMP
TV VOL
TV INPUT
TV MUTE
SCENE
1
2
3
4
SRCH MODE
MENU
BAND LEVEL
SCENE
TITLE
VOLUME
1
2
3
4
BAND LEVEL
SRCH
MENU
MODE VOLUME
TITLE
ENTER
ENTER
DISPLAY
RETURN
MEMORY
REC
DISPLAY
*2
RETURN
MEMORY
REC
INFO
*2
l
PROG
h
ENHANCER SUR. DECODE
1
2
3
4
INFO
STRAIGHT DIRECT
NIGHT
PARAMETER
5
6
7
8
l
PROG
h
ENHANCER SUR. DECODE
MULTI CH IN AUDIO SEL
9
SLEEP
ENT
1
2
3
4
0
10
STRAIGHT DIRECT
NIGHT
PARAMETER
5
6
7
8
MULTI CH IN AUDIO SEL
SLEEP
ENT
9
0
10
Notes
Notes
*1 These buttons always control this unit.
*2
*1 These buttons always control your TV regardless of whether
5
These buttons control this unit only when AMP is pressed.
4
you press DTV/CBL or not.
Remote control
Digital TV/Cable TV
Turns on or off the power.
TV POWER
TV CH +/–
Changes the channel number.
Increases or decreases the volume
level.
TV VOL +/–
Changes the input source.
Mutes the audio output.
TV INPUT
TV MUTE
*2
4
These buttons control your TV only when DTV/CBL is
pressed. For details, see the “Digital TV/Cable TV” column on
page 74.
y
You can control more than one TV by setting the appropriate
remote control code for any input source selector buttons other
4
than DTV/CBL. In such a case, you can control the buttons
highlighted above (*1 and *2) when you press the input source
selector button.
73 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control features
■ Controlling other components
Press one of the input selector buttons (4) or A to C
buttons to control other components. You must set the
appropriate remote control code for each input source in
advance (see page 75). The following table shows the
function of each control button used to control other
components assigned to each input selector button. Be
advised that some buttons may not correctly operate the
selected component.
SRCH MODE
MENU
BAND LEVEL
TITLE
VOLUME
[2]
[1]
POWER POWER
STANDBY
SIRIUS
POWER
MUTE
[7]
[8]
TV
AV
A
XM
ENTER
[3]
[4]
[5]
CD
DVD
MD/CD-R TUNER
RETURN
DISPLAY
MEMORY
TV CH
DTV/CBL
B
DVR
C
REC
V-AUX/DOCK
AMP
TV VOL
TV INPUT
TV MUTE
INFO
y
l
PROG
h
ENHANCER SUR. DECODE
1
2
3
4
• The remote control has 13 modes (input areas) to control
components so that the remote control can operate up to 13
different components.
SCENE
STRAIGHT DIRECT
NIGHT
7
PARAMETER
5
6
8
1
2
3
4
[6]
MULTI CH IN AUDIO SEL
SLEEP
ENT
9
0
10
[9]
• When you press one of the optional component control area
buttons (A to C), you can control the desired component
without changing the input source of this unit.
DVD player/
recorder
Digital TV/
Cable TV
MD/CD
recorder
Remote control
VCR
LD player
CD player
Tuner
[1] AV POWER
[2] TITLE
Power *1
Title
Power *1
Power *2
Power *1
Power *1
Power *1
Band
[3] PRESET/CH k
Preset up (1-8)/
Tuning up
Up
VCR channel up Up
VCR channel
Preset down
(1-8)/Tuning
down
PRESET/CH n
Down
Down
down
Preset down
(A-E)
A-E/CAT. l
A-E/CAT. h
Left
Left
Preset up
(A-E)
Right
Right
ENTER
[4] RETURN
[5] REC
Enter
Enter
Hold
Return
Return
Memory
Disc skip
(player)
Rec (recorder)
Rec
Rec *2
Disc skip
Play
Rec
p
Play
Play
Play *2
Play
Play
Search
backward
Searchbackward
*2
w
Search backward
Search backward Search backward Search backward Information
Search forward
*2
f
e
Search forward Search forward
Pause Pause
Skip backward Skip backward
Search forward
Pause
Search forward Search forward
Pause *2
Pause
Pause
Skip backward
*2
Audio program
down
b
Skip backward
Skip backward
Skip backward
Audio program
up
a
Skip forward
Stop
Skip forward
Stop
Skip forward *2 Skip forward
Stop *2 Stop
Skip forward
Stop
Skip forward
Stop
s
[6] 1-9, 0, +10
Preset stations
(1-8)
Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons Numeric buttons
[7] MENU
[8] DISPLAY
[9] ENT
Menu
Menu
Display
Enter
Search mode
Display
Title/Index
Display
Enter
Display
Display
Index
Display
Index
Chapter/Time
Enter
Notes
*1 This button is operational only when the original remote control supplied with the component has a POWER button.
*2 These buttons operate your DVD recorder only when you set the appropriate remote control code for DVR (see page 75).
74 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control features
Setting remote control codes
You can control other components by setting the
appropriate remote control codes. For a complete list of
available remote control codes, refer to “List of remote
control codes” at the end of this manual.
1
While pressing and holding one of the input
4
selector buttons ( ) on the remote control to
select the input area you want to set up,
2
press AV POWER for more than 3
seconds.
A
XM
SIRIUS
Remote control code default settings
CD
MD/CD-R TUNER
Input
source
Component
category
Default
code
Manufacturer
POWER
AV
DVD
DTV/CBL
B
DVR
C
CD
MD/CD-R
TUNER
DVD
CD
YAMAHA
YAMAHA
YAMAHA
YAMAHA
—
5013
5001
5007
2000
—
Press for 3
seconds
V-AUX/DOCK
CD-R
While holding down
TUNER
DVD
G
2
Press the numeric buttons (0 to 9) ( ) to
enter the four-digit remote control code for
the component to be used.
When the setting succeeds, “RemoteSetup OK”
appears; however, when it does not, “RemoteSetup
NG” appears in the front panel display.
DTV/CBL
V-AUX
DVR
—
TUNER
DVR
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
YAMAHA
5011
2011
5009
5017
5012
5009
5017
XM
TUNER
TUNER
TUNER
TUNER
TUNER
Notes
SIRIUS
A
• If the manufacturer of your component has more than one code,
try each of them until you find the correct one.
• If you do not press any buttons within 30 seconds in step 2, the
setup process is canceled. If this happens, repeat the setup
procedure.
B
C
Note
You may not be able to operate your Yamaha component even if a
Yamaha remote control code is preset as listed above. In this case,
try setting another Yamaha remote control code.
75 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced setup
Advanced setup
This unit has additional menus that are displayed in the
front panel display. The advanced setup menu offers
additional operations to adjust and customize the way this
unit operates. Change the initial settings (indicated in bold
under each parameter) to reflect the needs of your
listening environment.
■ Speaker impedance SP IMP.
(U.S.A. and Canada models only)
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers.
Choices: 8Ω MIN, 6Ω MIN
•
Select “8Ω MIN” to set the speaker impedance to 8 Ω.
Select “6Ω MIN” to set the speaker impedance to 6 Ω.
•
Notes
L
• Only ASTANDBY/ON, PROGRAM l/ h, and
SP IMP.
Speaker
Front (A or B)
Center
Impedance level
M
STRAIGHT are effective while you are using the advanced
setup menu.
The impedance of each
speaker must be 8 Ω or
higher.
• No other operations can be made while you are using the
advanced setup menu.
• The advanced setup menu is only available in the front panel
display.
8Ω MIN
Surround
Front (A or B)
Center
The impedance of each
speaker must be 6 Ω or
higher.
A
Press STANDBY/ON to set this unit to the
1
2
6Ω MIN
standby mode.
Surround
K
Press and hold TONE CONTROL and
A
then press STANDBY/ON to turn on this
■ SIRIUS Satellite Radio Parental Lock
code number reset SSR PIN
Use this feature to set the code number for the SIRIUS
Satellite Radio Parental Lock feature to the initial factory
setting.
unit.
This unit turns on, and the advanced setup menu
appears in the front panel display.
Choices: RESET, CANCEL
L
3
Press PROGRAM l/ hto select the
•
•
Select “RESET” to set the code number to the initial
factory setting.
Select “CANCEL” to set the code number to the initial
factory setting.
parameter you want to adjust.
The name of the selected parameter appears in the
front panel display.
M
Press STRAIGHT repeatedly to change
4
5
Note
the selected parameter setting.
Even if you set “SSR PIN” to “RESET”, this unit does not unlock
the locked channels. The initial factory setting of the Parental
Lock code number is “0000”.
A
Press STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
y
The settings you made are reflected next time you turn on this
unit.
76 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced setup
■ Tuner frequency step TU
(Asia and General models only)
Use this feature to set the tuner frequency step according
to the frequency spacing in your area.
Choices: AM10/FM100, AM9/FM50
•
•
Select “AM10/FM100” for North, Central and South
America.
Select “AM9/FM50” for all other areas.
■ Initializing INIT.
Use this feature to reset all the parameters of this unit to
the initial factory settings (see page 87).
Choices: CANCEL, RESET
•
Select “CANCEL” not to reset any parameters of this
unit.
•
Select “RESET” to reset the parameters of this unit.
Notes
• This setting completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
77 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
■ General
See
page
Problem
Cause
Remedy
This unit fails to turn
on or enters the
standby mode soon
after the power is
turned on.
The power cable is not connected or the
plug is not completely inserted.
Connect the power cable firmly.
—
The speaker impedance setting is
incorrect.
Set the speaker impedance to match your speakers.
21
11
The protection circuitry has been
activated.
Make sure that all speaker wire connections on this
unit and on all speakers are secure and that the wire
for each connection does not touch anything other
than its respective connection.
This unit has been exposed to a strong
external electric shock (such as lightning
or strong static electricity).
Set this unit to the standby mode, disconnect the
power cable, plug it back in after 30 seconds and then
use it normally.
—
No sound.
Incorrect input or output cable
connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
13-18
34
No appropriate Audio input jack select has Set an appropriate Audio input jack select.
been set.
Audio input jack select is set to “HDMI”,
“COAX/OPT” or “ANALOG”.
Set Audio input jack select to “AUTO”.
34
Audio input jack select is set to
“ANALOG” while playing a source
encoded in Dolby Digital or DTS.
Set Audio input jack select to “AUTO” or
“COAX/OPT”.
34
No appropriate input source has been
selected.
Select an appropriate input source with
33
O
INPUT l/ h(or the input selector buttons(4)).
Speaker connections are not secure.
Secure the connections.
11
33
The front speakers to be used have not
been selected properly.
JSPEAKERS
.
Select the front speakers with
The volume is turned down.
The sound is muted.
Turn up the volume.
—
35
JMUTE
N
Press
or VOLUME +/– to resume audio
output and then adjust the volume.
Signals this unit cannot reproduce are
being input from a source component,
such as a CD-ROM.
Play a source whose signals can be reproduced by this
unit.
—
14
67
The HDMI components connected to this
unit do not support the HDCP copy
protection standards.
Connect HDMI components that support the HDCP
copy protection standards.
“SUPPORT AUDIO” is set to “Other” and Set “SUPPORT AUDIO” to “HTR-6140” in
“HDMI” audio signals are not being
played back on this unit.
“MANUAL SETUP”.
78 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
See
page
Problem
Cause
Remedy
The sound suddenly
goes off.
The protection circuitry has been activated Check that the impedance setting is correct.
because of a short circuit, etc.
21
Check that the speaker wires are not touching each
other and then turn this unit back on.
—
The sleep timer has turned off this unit.
The sound is muted.
Turn on this unit, and play the source again.
—
35
JMUTE
Press
output.
N
or VOLUME +/– to resume audio
Sound is heard from
the speaker on one
side only.
Incorrect cable connections.
Connect the cables properly. If the problem persists,
the cables may be defective.
11-18
Incorrect settings in “SP LEVEL”.
Adjust the “SP LEVEL” settings.
This is not malfunction.
41
—
Only the center
speaker outputs
substantial sound.
When playing a monaural source with a
CINEMA DSP program, the source signal
is directed to the center channel, and the
front and surround speakers output effect
sounds.
No sound is heard
from the center
speaker.
“CENTER SP” in “SPEAKER SET” is set Set “CENTER SP” to “SML” or “LRG”.
to “NONE”.
63
38
64
39
Some sound field programs do not output
sounds from the center speaker.
Try another sound field program.
No sound is heard
from the surround
speakers.
“SUR. L/R SP” in “SPEAKER SET” is
set to “NONE”.
Set “SUR. L/R SP” to “SML” or “LRG”.
This unit is in the “STRAIGHT” mode
and a monaural source is being played
back.
C
Press STRAIGHT so that “STRAIGHT”
disappears from the front panel display.
No sound from the
center, surround
speakers when the
FRONT B speakers
are activated.
“FRONT B” in “SPEAKER SET” is set to Set “FRONT B” to “FRONT”.
“ZONE B”.
63
No sound is heard
from the subwoofer.
“LFE/BASS OUT” in “SPEAKER SET”
is set to “FRNT” when a Dolby Digital or
DTS signal is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
64
64
—
“LFE/BASS OUT” in “SPEAKER SET”
is set to “SWFR” or “FRNT” when a
2-channel source is being played.
Set “LFE/BASS OUT” to “SWFR” or “BOTH”.
This is not malfunction.
The source does not contain
low-frequency bass signals.
79 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
See
page
Problem
Cause
Remedy
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator in
the front panel
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operating
instructions for your component.
—
Audio input jack select is set to
“ANALOG”.
Set Audio input jack select to “AUTO”.
34
display does not light
up.)
A humming sound is
heard.
Incorrect cable connections.
Connect the audio cables firmly. If the problem
persists, the cables may be defective.
—
67
—
The volume level
cannot be increased,
or the sound is
distorted.
You are attempting to set the volume level Adjust “MAX VOL.” setting.
higher than the maximum volume level.
The component connected to the AUDIO
OUT (REC) jacks of this unit is turned
off.
Turn on the power of the component.
The sound effect
cannot be recorded.
It is not possible to record the sound effect This is not malfunction.
with a recording component.
—
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT (REC)
jacks.
The source component is not connected to Connect the source component to the analog AUDIO
14, 18
the analog AUDIO IN jacks of this unit.
IN jacks.
The sound field
“MEMORY GUARD” in “OPTION
Set “MEMORY GUARD” to “OFF”.
70
—
parameters and some MENU” is set to “ON”.
other settings of this
unit cannot be
changed.
This unit does not
operate properly.
The internal microcomputer has been
Disconnect the power cable from the AC wall outlet
and then plug it in again after about 30 seconds.
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
No sound is heard
from the connected
HDMI component.
The HDMI component does not accept the Convert the multi-channel audio signals to the
—
11
—
multi-channel audio signals.
2-channel audio signals at the source component such
as a DVD player.
“CHECK SP WIRES”
appears in the front
panel display.
Speaker cables are short-circuited.
Make sure all speaker cables are connected correctly.
Move this unit further away from such equipment.
There is noise
interference from
digital or radio
This unit is too close to the digital or
high-frequency equipment.
frequency equipment.
The picture is
disturbed.
The video source uses scrambled or
encoded signals to prevent dubbing.
This in not malfunction.
—
—
This unit suddenly
enters the standby
mode.
The internal temperature is too high and
the overheat protection circuitry has been
activated.
Wait about 1 hour for this unit to cool down and then
turn it back on.
80 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■ Tuner
See
page
Problem
Cause
Remedy
FM stereo reception is
noisy.
The characteristics of FM stereo
broadcasts may cause this problem
when the transmitter is too far away or
the antenna input is poor.
Check the antenna connections.
20
—
Try using a high-quality directional FM
antenna.
Use the manual tuning method.
43
—
There is distortion, and
clear reception cannot
be obtained even with a
good FM antenna.
There is multi-path interference.
The signal is too weak.
Adjust the antenna position to eliminate
multi-path interference.
FM
The desired station
cannot be tuned into
with the automatic
tuning method.
Use a high-quality directional FM antenna.
Use the manual tuning method.
—
43
Previously preset
stations can no longer
be tuned into.
This unit has been disconnected for a
long period.
Set preset stations.
44
—
The desired station
cannot be tuned into
with the automatic
tuning method.
The signal is weak or the antenna
connections are loose.
Tighten the AM loop antenna connections
and orient it for the best reception.
Use the manual tuning method.
43
—
AM
There are continuous
crackling and hissing
noises.
Noise can result from lightning,
fluorescent lamps, motors, thermostats
and other electrical equipment.
Use an outdoor antenna and a ground wire.
This will help somewhat, but it is difficult to
eliminate all noise.
There are buzzing and
whining noises.
A TV set is being used nearby.
Move this unit away from the TV set.
—
81 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■
XM Satellite Radio
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
See
page
Status message
Cause
Remedy
The XM Mini-Tuner is not installed in the Confirm the XM Mini-Tuner is fully seated in the
46
CHECK XM TUNER
XM Mini-Tuner Dock or the XM
Mini-Tuner Dock is not connected to this
unit.
dock and check the XM Mini-Tuner Dock cable is
connected to this unit.
The XM antenna is not connected to the
XM Mini-Tuner Dock or the XM antenna
cable has become damaged.
Check that the XM antenna is securely connected to
the XM Mini-Tuner Dock and check the antenna
cable for damage. Replace the XM antenna if the
cable is damaged.
46
47
CHECK ANTENNA
CH UNAUTH
You may be attempting to tune to an XM
channel that is blocked or that you cannot http://www.xmradio.com/ (US residents) and
Consult the latest channel guide at
receive with your XM subscription
package.
http://www.xmradio.ca/ (Canadian residents) for the
current list of channels. For information on receiving
this channel, visit http://www.xmradio.com/ (US
residents) and http://www.xmradio.ca/ (Canadian
residents) or contact XM Satellite Radio at
1-800-967-2346 (US residents) and 1-877-GET
XMSR (Canadian residents).
The XM Mini-Tuner is not receiving the
XM satellite signal. Something may be
blocking the XM antenna’s view of the
satellites or the antenna is not properly
aimed.
Check for antenna obstructions and reposition the
XM antenna to get better signal reception. Use the
“XM RADIO SET” screen in the video monitor to
check the antenna reception level. See instructions
supplied with the XM Mini-Tuner and Dock for
antenna installation information.
46,72
NO SIGNAL
LOADING
The XM Mini-Tuner is acquiring audio or This message should disappear in a few seconds in
program information from the XM
satellite signal. This message can also
72
good signal conditions. If you see this message often,
reposition the XM antenna to get better signal
occur in weak XM signal conditions. Note reception. Use the “XM RADIO SET” screen in the
that this unit may not respond to some
operations while this message is
displayed.
video monitor to check the antenna reception level.
The XM channel you selected is not
currently broadcasting.
Check back at a later time; in the mean time, select
another channel.
—
—
OFF AIR
The selected channel is not available. The Consult the latest channel guide at
CH UNAVAILABLE
channel may have been reassigned to a
different channel number. This message
may occur initially with a new XM
Mini-Tuner or a XM Mini-Tuner that has
not received XM’s signal for an extended
period.
http://www.xmradio.com/ (US residents) and
http://www.xmradio.ca/ (Canadian residents) for the
current list of channels. For cases of a new XM
Mini-Tuner or a XM Mini-Tuner that has not received
XM’s signal for an extended period, allow the XM
Mini-Tuner to receive the XM satellite signal for at
least 5 minutes and then try to select the channel
again.
No artist name or song title is available for No action required.
this selection.
—
- - - -
82 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■ SIRIUS Satellite Radio
If an operation takes longer than usual or an error occurs, one of the following messages may appear in the front panel
display. In this case, read the cause and follow the corresponding remedies.
See
page
Status message
Cause
Remedy
The antenna is not connected to the
SiriusConnect tuner properly.
Check the connection of the antenna and
SiriusConnect tuner.
51
ANTENNA ERROR
The SiriusConnect tuner is not connected
to the SIRIUS jack of this unit correctly.
Check the connection of the SiriusConnect tuner and
this unit.
51
51
CHECK SR TUNER
The SiriusConnect tuner is not connected
to the AC wall outlet.
Connect the power cable of the SiriusConnect tuner to
the AC wall outlet.
This unit does not support the connected
SIRIUS Satellite Radio tuner.
Connect the SiriusConnect tuner that this unit
supports,
51
NOT SUPPORTED
ACQUIRING
The signal is too weak.
Adjust the orientation of the antenna of the
SiriusConnect tuner. Use the “ANTENNA INFO”
information in the front panel display or “SIRIUS
Information” screen in the video monitor to check the
antenna reception level.
51, 56
The SiriusConnect tuner is updating the
channel list.
Wait until the updating is complete.
—
52
—
52
UPDATING
The period of the subscription is end.
Contact SIRIUS Satellite Radio to renew the
subscription.
The SiriusConnect tuner is updating the
firmware.
Wait until the updating is complete.
F/W UPDATING
The selected channel is not subscribed.
Contact SIRIUS Satellite Radio to subscribe the
selected channel.
URL: https://activate.siriusradio.com/
Phone: 1-888-539-SIRIUS (1-888-539-7474)
CALL SIRIUS
(CALL
888-539-SIRIUS
TO SUBSCRIBE)
Select another channel.
52
52
The subscription information is updated.
SUB UPDATED
INVALID
The selected channel is currently out of
service.
Select another channel.
The operation you made is not available.
Not Available
83 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■ AUTO SETUP
Before AUTO SETUP
See
page
Error message
Cause
Remedy
Optimizer microphone is not connected.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
24
Connect MIC!
Headphones are connected.
Unplug the headphones.
Unplug HP!
—
During AUTO SETUP
Error message
See
page
Cause
Remedy
Front L/R channel signals are not detected.
A surround channel signal is not detected.
Background noise is too loud.
Check the front L/R speaker connections.
Check the surround speaker connections.
11
11
—
E-1:NO FRONT SP
E-2:NO SUR.SP
E-4:NOISY
Try running “AUTO SETUP” in a quiet
environment.
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
24
24
The optimizer microphone was unplugged
during the “AUTO SETUP” procedure.
Connect the supplied optimizer microphone
to OPTIMIZER MIC jack on the front
panel.
E-6:NO MIC
The optimizer microphone does not detect
test tones.
Check the microphone setting.
E-7:NO SIGNAL
Check the speaker connections and
placement.
10, 11,
24
The “AUTO SETUP” procedure was
cancelled due to user activity.
Run “AUTO SETUP” again.
Run “AUTO SETUP” again.
24
E-8:USER CANCEL
An internal error occurred.
24
E-9:INTERNAL ERROR
84 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
After AUTO SETUP
See
page
Warning message
Cause
Remedy
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the speaker connections for proper
polarity (+ or –).
12
W-1:OUT OF PHASE
The distance between the nearest speaker
and the furthest speaker is out of adjustable position.
range.
Bring the speaker closer to the listening
—
24, 65
—
W-2:OVER 24m (80ft)
W-3:LEVEL ERROR
The difference of volume level among
speakers is excessive. (No level correction
is made.)
If “SWFR:TOO LOUD” or “SWFR:TOO
LOW” appears, adjust the output volume of
the subwoofer.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
Check the speaker connections.
Use speakers of similar quality.
11
—
Notes
• If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “AUTO SETUP” again.
• If a warning message “W-1”, “W-2”, or “W-3” appears, corrections are made, but they may not be optimal.
• If an error message “E-9” occurs repeatedly, please contact a qualified Yamaha service center.
■ iPod
Note
In case of a transmission error without a status message appearing in the front panel and in the OSD, check the connection to your iPod
(see page 19).
See
page
Status message
Cause
Remedy
This unit is in the middle of recognizing
the connection with your iPod.
Loading...
This unit is in the middle of acquiring
song lists from your iPod.
There is a problem with the signal path
from your iPod to this unit.
Turn off this unit and reconnect the Yamaha iPod
universal dock to the DOCK terminal of this unit.
19
Connect error
Try resetting your iPod.
—
—
The iPod being used is not supported by
this unit.
Only iPod (Click and Wheel), iPod nano, and iPod
mini are supported.
Unknown iPod
Your iPod is properly stationed in a
Yamaha iPod universal dock (YDS-10,
sold separately) connected to the DOCK
terminal of this unit, and the connection
between your iPod and this unit is
complete.
iPod connected
Your iPod was removed from a Yamaha
iPod universal dock (YDS-10, sold
separately) connected to the DOCK
terminal of this unit.
Station your iPod back in a Yamaha iPod universal
dock (YDS-10, sold separately) connected to the
DOCK terminal of this unit.
19
Disconnected
This unit cannot play back the songs
currently stored on your iPod.
Check that the songs currently stored on your iPod
are playable.
—
—
Unable to play
Store some other playable music files on your iPod.
85 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■ Bluetooth
See
page
Status message
Cause
Remedy
The Bluetooth adapter and the Bluetooth
component is in the middle of the pairing.
Searching...
The Bluetooth adapter and the Bluetooth
component is in the middle of establishing
the connection.
The paring is completed.
The paring is canceled.
Completed
Canceled
The connection between the Yamaha
Bluetooth adapter (such as YBA-10, sold
separately) and the Bluetooth component
is established.
BT connected
The Bluetooth component is disconnected
from the Yamaha Bluetooth adapter (such
as YBA-10, sold separately).
Disconnected
No BT Adapter
The Bluetooth adapter is not connected to Connect the Yamaha Bluetooth adapter (such as
the DOCK terminal. YBA-10, sold separately) to the DOCK terminal.
19
86 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
■ Remote control
See
page
Problem
Cause
Remedy
The remote control
does not work nor
function properly.
Wrong distance or angle.
The remote control functions within a maximum
range of 6 m (20 ft) and no more than 30 degrees
off-axis from the front panel.
23
Direct sunlight or lighting (from an
inverter type of fluorescent lamp, etc.) is
striking the remote control sensor of this
unit.
Reposition this unit.
—
The batteries are weak.
Replace all batteries.
3
The remote control code is not correctly
set.
Set the remote control code correctly using “List of
remote control codes” at the end of this manual.
75
Try setting another code for the same manufacturer
using “List of remote control codes” at the end of this
manual.
75
Even if the remote control code is
correctly set, there are some models that
do not respond to the remote control.
■ Resetting the system
Use this feature to reset all the parameters of this unit to
Notes
the initial factory settings.
• This procedure completely resets all the parameters of this unit
including the “SET MENU” parameters. However, the
advanced setup menu parameters will not be initialized.
• The initial factory settings are activated next time you turn on
this unit.
A
Press STANDBY/ON on the front panel to
1
2
set this unit to the standby mode.
y
K
Press and hold TONE CONTROL and
A
then press STANDBY/ON to turn on this
To cancel the initialization procedure at any time without making
M
any changes, press STRAIGHT repeatedly to select
unit.
A
“CANCEL” and then press STANDBY/ON.
The advanced setup menu appears in the front panel
display.
L
Press PROGRAM l/ hto select “INIT.”.
3
4
M
Press STRAIGHT repeatedly to select
“RESET”.
Select “CANCEL” to cancel the initialization
procedure without making any changes.
A
Press STANDBY/ON to confirm your
selection and set this unit to the standby
mode.
5
87 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
Glossary
■ CINEMA DSP
■ Dolby Pro Logic II
Since the Dolby Surround and DTS systems were
originally designed for use in movie theaters, their effect
is best felt in a theater having many speakers designed for
acoustic effects. Since home conditions, such as room
size, wall material, number of speakers, and so on, can
differ so widely, it is inevitable that there are differences in
the sound heard. Based on a wealth of actually measured
data, Yamaha CINEMA DSP uses Yamaha original sound
field technology to combine Dolby Pro Logic, Dolby
Digital and DTS systems to provide the audiovisual
experience of a movie theater in the listening room of your
own home.
Dolby Pro Logic II is an improved technique used to
decode vast numbers of existing Dolby Surround sources.
This new technology enables a discrete 5-channel
playback with 2 front left and right channels, 1 center
channel, and 2 surround left and right channels instead of
only 1 surround channel for conventional Pro Logic
technology. There are three modes available: “Music
mode” for music sources, “Movie mode” for movie
sources and “Game mode” for game sources.
■ Dolby Surround
Dolby Surround uses a 4-channel analog recording system
to reproduce realistic and dynamic sound effects: 2 front
left and right channels (stereo), a center channel for dialog
(monaural), and a surround channel for special sound
effects (monaural). The surround channel reproduces
sound within a narrow frequency range. Dolby Surround is
widely used with nearly all video tapes and laser discs,
and in many TV and cable broadcasts as well. The Dolby
Pro Logic decoder built into this unit employs a digital
signal processing system that automatically stabilizes the
volume on each channel to enhance moving sound effects
and directionality.
■ Component video signal
With the component video signal system, the video signal
is separated into the Y signal for the luminance and the PB
and PR signals for the chrominance. Color can be
reproduced more faithfully with this system because each
of these signals is independent. The component signal is
also called the “color difference signal” because the
luminance signal is subtracted from the color signal. A
monitor with component input jacks is required in order to
output component signals.
■ Composite video signal
■ DTS Digital Surround
With the composite video signal system, the video signal
is composed of three basic elements of a video picture:
color, brightness and synchronization data. A composite
video jack on a video component transmits these three
elements combined.
DTS digital surround was developed to replace the analog
soundtracks of movies with a 5.1-channel digital sound
track, and is now rapidly gaining popularity in movie
theaters around the world. DTS, Inc. has developed a
home theater system so that you can enjoy the depth of
sound and natural spatial representation of DTS digital
surround in your home. This system produces practically
distortion-free 5.1-channel sound (technically, left, right
and center channels, 2 surround channels, plus an LFE 0.1
channel as a subwoofer, for a total of 5.1-channels).
■ Dolby Digital
Dolby Digital is a digital surround sound system that gives
you completely independent multi-channel audio. With 3
front channels (front L/R and center), and 2 surround
stereo channels, Dolby Digital provides 5 full-range audio
channels. With an additional channel especially for bass
effects, called LFE (Low Frequency Effect), the system
has a total of 5.1-channels (LFE is counted as 0.1
channel). By using 2-channel stereo for the surround
speakers, more accurate moving sound effects and
surround sound environment are possible than with Dolby
Surround. The wide dynamic range from maximum to
minimum volume reproduced by the 5 full-range channels
and the precise sound orientation generated using digital
sound processing provide listeners with unprecedented
excitement and realism. With this unit, any sound
environment from monaural up to a 5.1-channel
configuration can be freely selected for your enjoyment.
88 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Glossary
■ HDMI
■ Sampling frequency and number of
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital audio/video
interface. Providing an interface between any source (such
as a set-top box or AV receiver) and an audio/video
monitor (such as a digital television), HDMI supports
standard, enhanced or high-definition video as well as
multi-channel digital audio using a single cable. HDMI
transmits all ATSC HDTV standards and supports
8-channel digital audio, with bandwidth to spare to
accommodate future enhancements and requirements.
When used in combination with HDCP (High-bandwidth
Digital Content Protection), HDMI provides a secure
audio/video interface that meets the security requirements
of content providers and system operators. For further
information on HDMI, visit the HDMI website at
“http://www.hdmi.org/”.
quantized bits
When digitizing an analog audio signal, the number of
times the signal is sampled per second is called the
sampling frequency, while the degree of fineness when
converting the sound level into a numeric value is called
the number of quantized bits. The range of rates that can
be played back is determined based on the sampling rate,
while the dynamic range representing the sound level
difference is determined by the number of quantized bits.
In principle, the higher the sampling frequency, the wider
the range of frequencies that can be played back, and the
higher the number of quantized bits, the more finely the
sound level can be reproduced.
■ SILENT CINEMA
Yamaha has developed a natural, realistic sound effect
DSP algorithm for headphones. Parameters for
headphones have been set for each sound field so that
accurate representations of all the sound field programs
can be enjoyed on headphones.
■ LFE 0.1 channel
This channel reproduces low-frequency signals. The
frequency range of this channel is from 20 Hz to 120 Hz.
This channel is counted as 0.1 because it only enforces a
low-frequency range compared to the full-range
reproduced by the other 5 channels in Dolby Digital or
DTS 5.1-channel systems.
■ Virtual CINEMA DSP
Yamaha has developed a Virtual CINEMA DSP algorithm
that allows you to enjoy DSP sound field surround effects
even without any surround speakers by using virtual
surround speakers. It is even possible to enjoy Virtual
CINEMA DSP using a minimal two-speaker system that
does not include a center speaker.
■ Neural Surround
™
Neural Surround represents the latest advancement in
surround technology and has been adopted by XM
Satellite Radio for digital radio broadcast of surround
recordings and live events in surround sound. Neural
™
Surround employs psychoacoustic frequency domain
processing which allows delivery of a more detailed sound
stage with superior channel separation and localization of
audio elements.
■ PCM (Linear PCM)
Linear PCM is a signal format under which an analog
audio signal is digitized, recorded and transmitted without
using any compression. This is used as a method of
recording CDs and DVD audio. The PCM system uses a
technique for sampling the size of the analog signal per
very small unit of time. Standing for “Pulse Code
Modulation”, the analog signal is encoded as pulses and
then modulated for recording.
89 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
• Signal Level
AUDIO SECTION
Composite ................................................................. 1 Vp-p/75 Ω
Component ................... 1 Vp-p/75 Ω (Y), 0.7 Vp-p/75 Ω (PB/PR)
• Minimum RMS Output Power for Front, Center, Surround
[U.S.A. and Canada models]
1 kHz, 0.9% THD, 8 Ω ................................................... 105 W
[Other models]
1 kHz, 0.9% THD, 6 Ω ................................................... 105 W
• Signal to Noise Ratio ................................................. 50 dB or more
• Maximum Input Level ........................................... 1.5 Vp-p or more
• Frequency Response (MONITOR OUT)
• Maximum Power for Front, Center, Surround (JEITA)
Component Signal ................................... 5 Hz to 60 MHz, –3 dB
1 kHz, 10% THD, 6 Ω ....................................................... 130 W
• Dynamic Power
FM SECTION
[U.S.A. and Canada models]
(IHF, 8/6/4/2 Ω) ........................................... 90/110/130/150 W
[Other models]
• Tuning Range
[U.S.A. and Canada models] .......................... 87.5 to 107.9 MHz
[Asia and General models] ....... 87.5/87.50 to 108.0/108.00 MHz
[Other models] ............................................ 87.50 to 108.00 MHz
(IHF, 6/4/2 Ω) .................................................... 100/110/125 W
• Dynamic Headroom [U.S.A. and Canada models]
• 50 dB Quieting Sensitivity (IHF, 100% mod.)
8 Ω ..................................................................................... 0.27 dB
Mono ................................................................. 2.8 µV (20.2 dBf)
• Maximum Input Signal
• Signal to Noise Ratio (IHF)
CD, etc. Effect On, 1 kHz, 0.5% THD .................... 2.0 V or more
Mono/Stereo ............................................................. 73 dB/70 dB
• Frequency Response
• Harmonic Distortion (1 kHz)
CD, etc. to Front L/R ............................ 10 Hz to 100 kHz, –3 dB
Mono/Stereo ................................................................ 0.5%/0.5%
• Total Harmonic Distortion
• Antenna Input (unbalanced) ..................................................... 75 Ω
[U.S.A. and Canada models]
(1 kHz, 45 W, Front L/R, 8 Ω ) ............................. 0.06% or less
[Other models]
(1 kHz, 50 W, Front L/R, 6 Ω ) ............................. 0.06% or less
AM SECTION
• Tuning Range
[U.S.A. and Canada models] .............................. 530 to 1710 kHz
[Asia and General models] ................. 530/531 to 1710/1611 kHz
[Other models] .................................................... 531 to 1611 kHz
• Signal to Noise Ratio (IHF-A Network)
CD (200 mV) to Front L/R, Effect Off ...................98 dB or more
CD (250 mV) to Front L/R, Effect Off .................100 dB or more
GENERAL
• Power Supply
• Residual Noise (IHF-A Network)
Front L/R ................................................................ 150 µV or less
[Europe and Russia models] .............................. 230 V AC, 50 Hz
[U.S.A. and Canada models] ............................. 120 V AC, 60 Hz
[Australia model] ............................................... 240 V AC, 50 Hz
[Korea model] .................................................... 220 V AC, 60 Hz
[China model] .................................................... 220 V AC, 50 Hz
[Asia model] ......................................... 220-240 V AC, 50/60 Hz
[General model] ...................... 110-120/220-240 V AC, 50/60 Hz
• Power Consumption
• Channel Separation (1 kHz/10 kHz)
CD, etc. (5.1 kΩ shorted) to Front L/R
................................................................... 60 dB/45 dB or more
• Tone Control (Front L/R)
BASS Boost/Cut .................................................... 10 dB/100 Hz
TREBLE Boost/Cut .............................................. 10 dB/20 kHz
• Headphone Jack Rated Output/Impedance .............. 400 mV/470 Ω
[U.S.A. and Canada models] ................................. 240 W/320 VA
[General model] .................................................................. 260 W
[Other models] .................................................................... 240 W
• Input Sensitivity/Input Impedance
CD, etc. ................................................................. 200 mV/47 kΩ
MULTI CH INPUT ............................................... 200 mV/47 kΩ
• Standby Power Consumption ................................................. 0.8 W
• Output Level/Output Impedance
• Maximum Power Consumption [Asia and General models only]
5ch, 10% THD .................................................................... 440 W
AUDIO OUT (REC) ............................................ 200 mV/1.2 kΩ
SUBWOOFER OUTPUT ........................................... 4 V/1.2 kΩ
• AC Outlets
• Filter Characteristics (fc=40/60/80/90/100/110/120/160/200 Hz)
H.P.F.
[Australia model] ........................................ 1 (100 W maximum)
[U.S.A., Canada and China models]... 2 (Total 100 W maximum)
[Other models]...................................... 2 (Total 50 W maximum)
(FRONT SP, CENTER SP, SUR. L/R SP:
SMALL/SML) ............................................................12 dB/oct.
L.P.F. (Subwoofer) .........................................................24 dB/oct.
• Dimensions (W x H x D).................................. 435 x 151 x 352 mm
(17-1/8” x 5-15/16” x 13-7/8”)
VIDEO SECTION
• Video Signal Type (Gray back)
• Weight .............................................................. 8.5 kg (18 lbs 12 oz)
[U.S.A., Canada, Korea and General models] .................... NTSC
[Other models] ....................................................................... PAL
* Specifications are subject to change without notice.
90 En
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Index
C)SP DISTANCE, Sound menu ..........65
CALL SIRIUS, SIRIUS Satellite Radio
status message ..................................83
Canceled, Troubleshooting ..................86
CAT SEARCH, XM tuning .................53
Category Search mode, XM tuning ......48
CD player, Connection .........................18
CD recorder, Connection .....................18
Center speaker equalizer,
Center speaker, Speaker settings ..........63
Center width, Sound field parameter ...40
message ............................................82
CHECK SR TUNER, SIRIUS Satellite
COAXIAL IN (1), Input assignment ...68
COAXIAL INPUT assignment,
■
Symbols
■
<XM> - - -,
Decoder indicators ............................... 22
DIGITAL AUDIO OPTICAL jacks .... 13
Sound field parameter ..................... 40
DIRECT ............................................... 41
XM tuning status message ...............82
■
Numerics
1 SOUND MENU, Manual setup ........61
2 INPUT MENU, Manual setup ..........61
2ch Stereo, Sound field program .........38
3 OPTION MENU ...............................70
3 OPTION MENU, Manual setup .......62
5ch Stereo, Sound field program .........38
■
A
A)DISPLAY SET, Option menu .........70
A)INPUT ASSIGNMENT,
Input menu .......................................68
A)SPEAKER SET, Sound menu .........63
A.DELAY, Audio settings ...................66
ACQUIRING, SIRIUS Satellite Radio
status message ..................................83
Activating XM Satellite Radio ............47
ALL CH SEARCH, XM tuning ...........53
All Channel Search mode,
Disconnected,
Disconnected,
COAXIAL INPUT jacks ......................68
Completed, Bluetooth status message ..86
Connect error, iPod controlling status
message ............................................85
Connect MIC!,
Display settings, Option menu ............ 70
information ...................................... 50
DTS decoder prioritize setting,
XM tuning ..................................48, 53
AM antenna connection .......................20
AM tuning ............................................43
Amplifier function OSD display time,
Display settings ................................70
ANTENNA ERROR, SIRIUS Satellite
Radio status message .......................83
Audio components, Connection ...........18
Audio delay, Audio settings .................66
Audio information ................................36
Audio input jacks selection ..................34
AUDIO jacks .......................................13
Audio jacks ..........................................13
AUDIO SELECT .................................34
Audio select, Option menu ..................71
Audio settings, Sound menu ................66
Audio signal flow .................................14
AUTO SETUP .....................................24
AUTO SETUP, Error message ............84
Automatic preset tuning,
Auto setup error message .................84
Connecting to the FRONT A
terminals ...........................................12
Connection, AM antenna connection ...20
Connection, Audio components ...........18
Connection, CD recorder .....................18
Connection, DVD player ......................16
Connection, DVD recorder ..................17
Connection, external decoder ...............18
Connection, FM antenna ......................20
Connection, HDMI ...............................14
Connection, MD recorder .....................18
Connection, Power cable ......................20
Connection, VCR .................................17
Controlling a TV ..................................73
Remote control .................................74
Controlling this unit, Remote control ...73
CROSSOVER, Speaker settings ..........64
Crossover, Speaker settings .................64
CT WIDTH, Sound field parameter .....40
Current status display ...........................35
■
E)LFE LEVEL, Sound menu .............. 66
Option menu .............................. 71, 72
Auto setup error message ................ 84
E-7:NO SIGNAL,
Auto setup error message ................ 84
E-8:USER CANCEL,
Auto setup error message ................ 84
E-9:INTERNAL ERROR,
FM/AM tuning .................................44
Automatic tuning, FM/AM tuning .......43
■
B
B)INPUT RENAME, Input menu .......68
B)MEMORY GUARD,
Option menu ....................................70
B)SPEAKER LEVEL, Sound menu ....65
Background Video,
Multi channel input setup ................69
BGV, Multi channel input setup ..........69
Bluetooth setting, Option menu ...........71
BT connected,
Bluetooth status message .................86
■
C
Auto setup error message ................ 84
Effect level, Sound field parameter ..... 40
C)AUDIO SELECT, Option menu ......71
91 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
ENHANCER indicator ........................ 22
Exchange, Preset station,
FM/AM tuning ................................. 45
External decoder connection ................ 18
■
J
■
XM tuning status message .............. 82
OPTICAL IN (3), Input assignment .... 68
OPTICAL INPUT assignment,
OPTIMIZER MIC jack, Auto setup .... 24
Optimizer microphone ......................... 24
Optimizer microphone, Auto setup ..... 24
Optimizing speaker setting .................. 24
■
L
iPod controlling status message .......85
Low-frequency effect level,
Sound menu .....................................66
■
F
F)DYNAMIC RANGE,
Sound menu ..................................... 66
F)XM RADIO SET .............................. 72
F/W UPDATING, SIRIUS Satellite Radio
status message ................................. 83
Factory presets, Advanced setup ......... 77
FL SCROLL, Display settings ............. 70
FM antenna .......................................... 20
FM antenna connection ........................ 20
FM tuning ............................................ 43
FRONT B speaker setting,
■
Speaker settings ............................... 63
FRONT B, Speaker settings ................. 63
Front panel display ............................... 22
Front panel display scroll,
Display settings ............................... 70
FRONT SP, Speaker settings ............... 63
Front speakers, Speaker settings .......... 63
FM/AM tuning .................................44
MANUAL SETUP, SET MENU .........61
Manual setup, SET MENU ..................61
Memory guard, Option menu ...............70
Menu browse mode, iPod controlling ..58
selection ...........................................34
Input menu .......................................69
with headphones ..............................39
Sound field program ........................38
Music Enh. 5ch,
Remote control ................................ 74
■
PANORAMA,
Panorama, Sound field parameter ....... 40
Parameter initialization,
Option menu .................................... 71
PARENTAL LOCK,
SIRIUS Satellite Radio setting ........ 72
PHONES jack ...................................... 35
Play information display,
iPod controlling ............................... 58
in the background ............................ 36
PLII Music ........................................... 39
Power cable, Connection ..................... 20
Preset channel setting,
XM tuning ................................. 49, 54
Preset Search mode,
XM tuning ................................. 48, 53
XM tuning ....................................... 53
Preset station exchange,
FM/AM tuning ................................ 45
Preset station selection,
FM/AM tuning ................................ 45
Pure hi-fi sound ................................... 41
PVR connection ................................... 17
■
G
G)AUDIO SET, Sound menu .............. 66
G)SIRIUS SET .................................... 72
G)SIRIUS SET, Option menu ............. 72
Games, Sound field program ............... 38
■
H
H) HDMI SET, Sound menu ............... 67
Hall, Sound field program ................... 38
HDMI indicator .................................... 22
HDMI set, Sound menu ....................... 67
HDMI, Connection .............................. 14
HEADPHONE, Dynamic range .......... 66
Headphone, Dynamic range ................. 66
HEADPHONE,
Low-frequency effect level .............. 66
Headphone,
Low-frequency effect level .............. 66
Headphones .......................................... 35
Headphones indicator .......................... 22
■
I
Infrared window, Remote control ........ 23
INI.VOL., Audio settings .................... 67
Initial volume, Audio settings .............. 67
Input assignment, Input menu .............. 68
Input channel and speaker indicators ... 23
Input channel indicators ....................... 23
Input menu, Manual setup ................... 61
Input rename, Input menu .................... 68
Input source indicators ......................... 22
Input source information display ......... 36
INVALID, SIRIUS Satellite Radio
status message ................................. 83
iPod connected, iPod controlling status
message ............................................ 85
iPod control, Status message ............... 85
iPod using ............................................ 57
■
Night listening mode ............................42
Bluetooth status message .................86
XM tuning status message ...............82
Not Available, SIRIUS Satellite Radio
status message ..................................83
Radio status message .......................83
Number of speakers .............................26
Number of speakers,
■
R
Remote control codes ........................... iii
Remote control, Troubleshooting ........ 87
Rename, SCENE template .................. 31
Repeat .................................................. 58
Repeat, iPod controlling ...................... 58
Resetting the system ............................ 87
Auto setup result ..............................26
92 En
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
SPEAKER,
W-2:DISTANCE ERROR,
■
S
Low-frequency effect level ..............66
Specifications .......................................90
SSR PIN, Advanced setup ....................76
Straight .................................................39
SUB UPDATED, SIRIUS Satellite Radio
status message ..................................83
SUBWOOFER PHASE,
Subwoofer phase, Speaker settings ......64
SUR. L/R SP, Speaker settings ............64
Auto setup error message ................ 85
Auto setup error message ................ 85
WIRING/LEVEL ................................ 25
WIRING/LEVEL, Auto setup ............. 25
SCENE ...................................................7
SCENE template selection ...................28
Searching...,
Bluetooth status message .................86
Selection, Audio input jacks ................34
Selection,
■
MULTI CH INPUT component ......34
Selection, Preset station,
XM ANTENNA,
XM Radio setting ............................ 72
XM Radio antenna ............................... 72
XM Radio setting ............................ 72
XM Satellite Radio .............................. 82
XM Satellite Radio, Status message .... 82
FM/AM tuning .................................45
Selection, SCENE template .................28
SET MENU ..........................................61
Setting remote control codes ................75
Setting SCENE template input source,
Remote control ................................32
Set-top box connection ........................17
Shuffle, iPod controlling ......................58
SILENT CINEMA ...............................39
SILENT CINEMA indicator ................23
Simple remote mode,
iPod controlling ...............................57
SIRIUS Satellite Radio ........................83
SIRIUS Satellite Radio parental lock ..72
SIRIUS Satellite Radio Parental Lock,
Advanced setup ................................76
SIRIUS Satellite Radio setting ............72
SIRIUS Satellite Radio setting,
Option menu ....................................72
SIRIUS Satellite Radio tuning .............51
SiriusConnect tuner ..............................51
SIZE .....................................................25
SIZE, Auto setup ..................................25
SLEEP indicator ..................................23
Sleep timer ...........................................37
Sound field programs
■
T
Tonal quality adjustment ......................41
Advanced setup ................................77
Turning on the power ...........................21
■
Yamaha iPod universal dock,
Connection ...................................... 19
Optimizer ......................................... 24
YPAO .................................................. 24
YPAO (Yamaha Parametric Room
Acoustic Optimizer) ........................ 24
■
U
status message ..................................85
Unit, Speaker distance ..........................65
Auto setup error message .................84
status message ..................................83
with headphones ..............................39
Sound menu, Manual setup ..................61
Source feature OSD display time,
Display settings ................................70
SP .........................................................26
SP A B indicators .................................22
SP IMP., Advanced setup ....................76
SP, Auto setup result ............................26
Speaker distance ............................25, 26
Speaker distance, Auto setup ...............25
Speaker distance, Auto setup result .....26
Speaker distance, Sound menu ............65
Speaker distances, Speaker distance ....65
Speaker impedance setting ...................21
Speaker impedance, Advanced setup ...76
Speaker level ........................................26
Speaker level adjustment .....................41
Speaker level, Auto setup result ..........26
Speaker level, Sound menu ..................65
Speaker settings, Sound menu .............63
Speaker size .........................................25
Speaker size, Auto setup ......................25
Speaker wiring .....................................25
Speaker wiring, Auto setup ..................25
Speaker wiring/volume level,
■
VCR connection ...................................17
Video jacks ...........................................13
Video signal flow .................................14
Video sources in the background .........36
VOLUME level indicator .....................22
Volume Trim, Input menu ....................69
J
“
SPEAKERS” or “4DVD” (example)
indicates the name of the parts on the front
panel or the remote control. Refer to the
attached sheet or the pages at the end of this
manual for the information about each
position of the parts.
Auto setup ........................................25
SPEAKER, Dynamic range .................66
Speaker, Dynamic range ......................66
■
W
W-1:OUT OF PHASE,
Auto setup error message .................85
93 En
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Front panel
A
B
C
D
E
F GH
I
VOLUME
STANDBY
/ON
OPTIMIZER MIC
INFO
TUNING AUTO/MAN'L
EDIT
SEARCH MODE
PRESET/TUNING
CATEGORY
A/B/C/D/E
BAND
l
PRESET/TUNING/CH
h
MEMORY
SCENE
1
2
3
4
VIDEO AUX
AUDIO
l
PROGRAM
h
l
INPUT
h
VIDEO
L
R
PORTABLE
SPEAKERS
A/B/OFF
PHONES
TONE CONTROL
STRAIGHT
DIRECT
AUDIO SELECT
SILENT CINEMA
EFFECT
J
K
L
M N
O
P Q
i
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Remote control
1
POWER POWER
STANDBY
POWER
MUTE
H
I
2
3
TV
AV
A
XM
SIRIUS
J
K
CD
DVD
MD/CD-R TUNER
TV CH
DTV/CBL
B
DVR
C
4
V-AUX/DOCK
AMP
L
TV VOL
TV INPUT
TV MUTE
5
6
SCENE
1
2
3
4
M
N
O
SRCH MODE
MENU
BAND LEVEL
VOLUME
TITLE
7
8
9
ENTER
DISPLAY
RETURN
MEMORY
REC
0
A
INFO
P
Q
R
l
PROG h
ENHANCER SUR. DECODE
B
1
2
3
4
STRAIGHT DIRECT
5
NIGHT PARAMETER
C
D
E
F
6
7
8
S
t
MULTI CH IN AUDIO SEL
SLEEP
ENT
9
0
10
G
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
List of remote control codes
MBO
2078
2072
2072
2073
2072
2035
2075
2078
2077
2073, 2135
2075
2075
2074
2030, 2040, 2054,
2057, 2105, 2110
2019, 2026, 2046,
2073, 2081, 2090
2036, 2082
2077
2075
2031, 2042, 2050,
2051
2076
2074
2075, 2078, 2086
2077
2085
2074
2032, 2041, 2104,
2113
2074
2095
Yamaha
2000, 2001, 2003,
2030, 2101
2078
Microsoft
Mind
Niveus Media 2132
Northgate
Panasonic
2132
2132
Blu-ray player
Medion
Micromaxx
Micromedia
Microstar
Mitsubishi
Mizuda
Mustek
Naiko
Onkyo
Orava
P&B
Pacific
Samsung
2137
Yukai
Zenith
2038, 2047, 2073
2132
2015, 2016, 2017,
2120
2117, 2121, 2123,
2128
2012, 2013, 2014
2129
CD player
DVD Recorder
Apex
JVC
LG
Yamaha
5000, 5013
2024
2070
2071
2020, 2065, 2066,
2067
2019, 2061, 2062,
2063
2021
2018
2022, 2064
2068
Philips
CD Recorder
Yamaha
5001
Pioneer
Proscan
RCA
Panasonic
DVD
Acoustic Solutions
2116, 2124, 2129,
2133
Philips
2078
ReplayTV
Sharp
Sonic Blue
Sony
2118, 2119, 2120
2009, 2010
2119, 2120
2005, 2006, 2007,
2122, 2130, 2131,
2132
2132
2132
2132
Aiwa
Akai
2055, 2100
2096
Panasonic
Pioneer
RCA
Sony
Toshiba
Yamaha
Yukai
Akura
2076
Philips
Alba
Apex
Awa
2078, 2086
2027, 2049
2078
Pioneer
Proline
Provision
RCA
2023
2069
Stack 10
Stack 9
Systemax
Tagar Systems 2132
Tivo
Axion
2078
DVD/LD
Pioneer
Brainwave
Brandt
Broksonic
Bush
Centrex
Classic
Clatronic
Coby
2096
2073, 2085
2060
2075, 2078, 2112
2077
2078
2036
Red Star
Reoc
Roadstar
Rowa
Saba
Sabaki
Samsung
2116, 2121, 2122,
2123, 2130, 2131
2004, 2125, 2132
2132
2133
2132
2132
2011
2132
DVD/VCR
JVC
LG
Panasonic
1017, 2045
1071, 2087
1020, 1072, 2040,
2105
Toshiba
Touch
UltimateTV
Viewsonic
Voodoo
2075
2078
C-Tech
CyberHome
Daewoo
Dansai
Daytek
DEC
2074
Philips
RCA
Samsung
Sharp
1025
2025, 2079, 2091
2092, 2098
2096
2080, 2089
2075
1022, 2042
1021, 2041, 2104
1023, 1073, 2043,
2106
1019, 1074, 2039,
2107
1024, 1075, 2044,
2108
1026, 2047
Yamaha
ZT Group
Sansui
Sanyo
ScanMagic
Scientific Labs 2074
Scott
SEG
Sharp
HD DVD
Toshiba
2078
Sony
2136
Denon
Denver
Diamond
DK Digital
Dual
2030, 2102, 2103
2075, 2076
2074
2094
2078
2088
iPod
Yamaha
2074, 2086
2034, 2043, 2059,
2093, 2106
2076
2074
2074, 2078
2076
Toshiba
5011
Zenith
LD player
Yamaha
Silva
Singer
DVD-DVR
Panasonic
Pioneer
Samsung
Toshiba
D-Vision
DVX
2096
2074
2002
Skymaster
Skyworth
SM Electronic 2074, 2078
2067
2114
2115
2068
MD
Yamaha
Elta
2096
Euroline
Funai
2096
2052, 2058
5002, 5003, 5004
Sony
2028, 2029, 2039,
2083, 2107
2074
2074
2074
2074
2075
2074, 2078
2052, 2058
2074
2072
2074
2076
2030
2096
2096
TAPE DECK
Yamaha
Global Solutions2074
Global Sphere 2074
DVR
ABS
Alienware
CyberPower
Dell
Soundmaster
Soundmax
Standard
Star Cluster
Starmedia
Supervision
Sylvania
Synn
TCM
Teac
Tec
Technics
Technika
Technosonic
Tevion
Thomson
Tokai
5005, 5006
Goodmans
Grundig
H&B
2075, 2077, 2078
2077, 2098
2075
2132
2132
2132
2132
2123, 2128, 2129,
2133
TUNER
Yamaha
5007, 5008, 5009,
5010, 5012, 5014,
5015, 5016, 5017,
5018
Haaz
2074
HE
2078
DIRECTV
Hitachi
2032, 2072
Home Electronics
2078
DISH Network 2126, 2127
TV
Acer
Acme
Acura
ADA
Dishpro
Echostar
Expressvu
Gateway
GOI
Hewlett Packard2132
Hitachi 2008
Howard Computers
2132
2126
2126, 2127
2126
2132
2126
Innovation
Irradio
JDB
2072
2134
2078
0093
0207
0208
0255
JVC
2033, 2045, 2053,
2073, 2099
2030, 2097
2075
ADC
Admiral
0206
Kenwood
Kingavon
Koda
2072, 2074
2085, 2109
2076
2026, 2044, 2048,
2056, 2073, 2108,
2111
0058, 0205, 0206,
0210, 0211
0200, 0207
0200
0206
0204
2075
Adyson
Agashi
Agazi
AGB
Lawson
Lenco
2074
2075
Toshiba
HTS
2126
2123, 2128
2123
Hughes
Humax
Hush
LG
Lifetec
Limit
2084, 2087
2072
2074
United
Voxson
2078
2078
2132
Aiko
0127, 0200, 0207,
0208
iBUYPOWER 2132
LogicLab
Luxor
2074
2077
Wharfedale
Xlogic
2074
2074
JVC
Linksys
2126, 2127
2132
Aiwa
0028, 0139, 0229,
0237
Magnavox
Magnum
2037, 2073, 2075
2072
Yakumo
Yamada
2077
2077
Media Center PC
2132
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Akai
0059, 0065, 0127,
0129, 0130, 0200,
0204, 0208, 0209,
0213, 0217, 0218,
0255
0209, 0218
0206, 0209, 0218
0200
0200, 0207, 0208,
0209, 0217, 0218
0212
0213
0207
Cascade
Cathay
CCE
Celebrity
Centurion
Century
CGE
0208
0213, 0217
0127
0059
0213, 0217
0205
0214, 0215
0208, 0218
0060, 0061, 0062,
0064
Envision
Erres
ESA
0060, 0061
0213, 0217
0080
0208
0206
Hisawa
Hitachi
0209, 0218
0006, 0014, 0015,
0016, 0042, 0060,
0061, 0095, 0105,
0127, 0156, 0179,
0180, 0204, 0207,
0210, 0211, 0215,
0216, 0251
0213
0209, 0218
0200, 0207
0200, 0207
0200, 0207, 0208,
0214, 0215
0206, 0207, 0213,
0217
0127, 0200, 0206,
0207, 0208, 0209,
0213, 0218
0200, 0218
0062
0211, 0213, 0214,
0215
0213, 0217
0063
0211
0208
0201, 0204, 0207,
0208, 0209, 0213,
0217, 0218
0206, 0208
0208, 0214
0205, 0211, 0213,
0214, 0216, 0217
0200
0206, 0207, 0218
0201, 0208, 0209,
0213, 0217, 0218
0209, 0218
0207, 0215
0200, 0209, 0213,
0218
0129, 0208, 0211
0208, 0217
0063
0057, 0060, 0061
0059
0060, 0061
Etron
Euro-Feel
Euroline
Euroman
Euromann
Europhon
Akiba
Akura
Alaron
Alba
0217
0200
Cimline
Citizen
0206, 0207, 0213
0200, 0204, 0207,
0213, 0215
0208
0212, 0217, 0226
0200, 0207, 0210
0210
0204, 0205, 0207,
0213, 0215, 0217
0200, 0207, 0208,
0213, 0214
0064, 0127, 0128,
0205, 0207, 0215
0213, 0218
0200, 0205, 0207,
0215, 0217
Hornyphon
Hoshai
Huanyu
Hygashi
Hyper
ALBIRAL
Allstar
Amplivision
Amstrad
City
Clarivox
Clatronic
0208
Fenner
0212, 0217
0206, 0207, 0208,
0209, 0213, 0214,
0218
Ferguson
Fidelity
Finlandia
Finlux
0204, 0206, 0208,
0209, 0218
0062
Hypson
ICE
Amtron
Anam
Anam National 0062
CMS
0200
0208
Colortyme
Concerto
Concorde
Condor
Contec
Contec/Cony 0062
Continental Edison
0216
Cosmel
Craig
Crosley
Crown
0060, 0061
0060, 0061
0208
0200, 0207, 0213
0200, 0207, 0208
Firstline
Fisher
Anglo
0208
Anitech
Ansonic
AOC
0206, 0208
0203, 0208
0060, 0061
0118, 0122, 0132
0216
0200
0207
0213, 0217
0205, 0211
0213
ICeS
IMA
Imperial
Flint
Formenti
Apex
Arc en Ciel
Arcam
Arcam Delta
Aristona
ASA
Asberg
Astra
Asuka
Formenti-Phoenix
0200
Fortress
Indiana
Infinity
Ingelen
Ingersol
Inno Hit
0208
0062
0205, 0214, 0215
0062, 0063, 0128,
0208, 0213, 0217
0205
0206, 0208, 0210,
0211, 0214
0023, 0024, 0025,
0088, 0127
0033, 0034, 0035,
0036, 0037, 0062,
0206
Frontech
Fujitsu
Funai
0208
CS Electronics 0200, 0207, 0209,
0214, 0218
CTC
Curtis Mathes 0057, 0060, 0061,
0064, 0065
CXC
0200, 0206, 0207,
0209, 0218
0200, 0207, 0213,
0217
Innovation
Interbuy
Interfunk
0214
Atlantic
Futuretech
Gateway
GBC
0062
0094
Atori
Audiosonic
0208
0062
International
Intervision
Irradio
0207, 0208, 0209,
0213, 0216, 0217,
0218
0207
0062
0205, 0206, 0207
0200
0216
Cybertron
Daewoo
0209, 0218
0060, 0061, 0120,
0127, 0155, 0193,
0200, 0207, 0208,
0213, 0218, 0238
0200, 0209, 0218
0200, 0206, 0213,
0217
0217
0060, 0061, 0208
0210
0204, 0207, 0213,
0217
0213, 0217
0200
0057
0208, 0213, 0217
0208
0207, 0215, 0216
0207, 0208, 0215
0060, 0127, 0205,
0207
0126
0217
0213, 0217
0203, 0204, 0212,
0218
0208, 0215, 0218
0057, 0060, 0061,
0122, 0147
0204, 0207, 0211,
0213, 0217
GE
AudioTon
Audiovox
Autovox
Awa
Baird
Bang & Olufsen 0205
GEC
Isukai
ITC
ITS
Dainichi
Dansai
Geloso
General Technic 0208
Genexxa
0208, 0210, 0215
0209, 0211, 0213,
0218
0060
0200
ITT
ITV
JBL
JC Penney
JCB
Dantax
Daytron
De Graaf
Decca
Basic Line
0208, 0209, 0213,
Gibralter
GoldHand
GoldStar
0218
0207
0217
0228
0060
Bastide
Baur
Beko
0060, 0061, 0127,
0128, 0200, 0201,
0207, 0208, 0210,
0213, 0214, 0215,
0217
0171, 0201, 0204,
0206, 0208, 0213,
0217, 0240
0209, 0218
0211
0204, 0207, 0210,
0213, 0217
0208, 0209, 0217
0128, 0130, 0222,
0236, 0255
0062
0200, 0206, 0207
0060, 0061
0200, 0207
0203, 0207, 0208,
0213, 0215, 0217
0204, 0208
0062
Jensen
JVC
Desmet
Diamond
Dimensia
Dixi
DTS
Dual
0017, 0018, 0019,
0108, 0136, 0153,
0178, 0190, 0213,
0218
0200, 0207, 0208,
0209, 0218
0207
0200, 0207
0211
0207, 0208, 0212,
0217
0059, 0060, 0061,
0200
0128, 0210
0215
0060, 0061
Belcor
Bell & Howell 0058, 0064
Benq
Beon
Bestar
Binatone
Black Star
Blaupunkt
Blue Sky
Bondstec
Boots
0081
0213, 0217
0213
0207
0214
0255
0209, 0218
0214
0207
0062
0216, 0226
0205, 0213, 0217
0200, 0207
0060
0138
0205
Goodmans
Kaisui
Dual-Tec
Dumont
GPM
Graetz
Granada
Kamosonic
Kamp
Kapsch
Durabrand
Dux
Dynatron
Elbe
Karcher
Grandin
Grundig
Kawasho
Bradford
Brandt
Grunpy
Halifax
Hallmark
Hampton
Hanseatic
Kendo
Kennedy
Kenwood
Kingsley
Kloss Novabeam
Brionvega
Britannia
Brockwood
Broksonic
Bruns
BSR
BTC
Bush
Elbe-Sharp
Elcit
ELECTRO TECH
0208
Electroband
Electrohome
Elin
0204
0204, 0205
0200, 0207
0059
0062
0203
0213
0209, 0218
0213, 0217
0205
0208
0062, 0127, 0207
0200, 0212
0215
0059, 0060, 0061
0200, 0207, 0213,
0217
0209, 0213, 0218
0215
0200, 0208
0060, 0061, 0062,
0064, 0128, 0205
Hantarex
Harvard
HCM
Kneissel
Kolster
Konka
Korpel
Korting
Koyoda
KTV
0209, 0218
0177, 0208, 0209,
0210, 0213, 0215,
0216, 0217, 0218,
0230, 0237
0060, 0061
0206
0206, 0207, 0208,
0218
0216
0200
0208, 0209, 0213,
0217, 0218
Elite
Elman
Elta
Hifivox
Higashi
Hinari
Candle
Capsonic
Emerson
Kyoto
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Lenco
Lenoir
Lesa
Leyco
LG
0208
0207, 0208
0214
NEC
0026, 0053, 0060,
0061, 0096, 0127
0205, 0207, 0210,
0213, 0217, 0255
0213, 0217
0214
0082, 0101
0208, 0213
0209, 0218
0200, 0207
0200, 0206, 0207,
0209, 0213, 0217,
0218
0061
0200, 0207
0216
0129, 0211
0205, 0211, 0213,
0216
0217
0211
0084
0207
0062, 0218
0213
0126, 0204, 0208,
0213, 0217, 0235
0218
0182, 0194, 0195,
0211, 0213, 0216,
0217, 0250
0206, 0213
0075
Sanyo
SBR
SCHAUB LORENTZ
0211
Schneider
0020, 0021, 0022,
0049, 0060, 0064,
0127, 0128, 0200,
0203, 0207, 0215
0217
Neckermann
0206, 0213, 0217
0016, 0038, 0039,
0127, 0128, 0157,
0158, 0163, 0164,
0166, 0188, 0189,
0200, 0201, 0207,
0208, 0210, 0213,
0214, 0215, 0217
0217
Plantron
Polaroid
Poppy
NEI
Nesco
0208
0060, 0061
NET-TV
New Tech
New World
Nicamagic
Nikkai
Portland
Prandoni-Prince 0204, 0210
0207, 0209, 0213,
0215, 0216, 0217,
0218
Precision
Prima
Profex
Profi-Tronic
Proline
Proscan
Prosonic
Protech
0207
0208, 0211
0208
0213
0213
Scotch
Scott
Sears
0061
Liesenk
Life
Lifetec
Loewe
0060, 0061, 0062
0057, 0060, 0061,
0064
0200, 0206, 0207,
0214, 0215, 0217
0204
0206, 0208
0206, 0208, 0218
0063, 0128, 0203,
0204, 0223, 0227
0205, 0213, 0217
0058
0210, 0217
0210, 0213, 0217
0213
Nikko
0057
Nobliko
Nogamatic
Nokia
0200, 0207, 0217
0206, 0207, 0208,
0213, 0214, 0215,
0217
0060, 0061
0217
0060
0213, 0217
0208
0152, 0214
0201, 0206, 0207,
0213, 0214, 0215,
0217
0218
0064
SEG
SEI
Loewe Opta
Logik
Luma
Lumatron
Lux May
Luxman
Luxor
Nordmende
SEI-Sinudyne 0204, 0205, 0211
Proton
Provision
Pulsar
Pye
Pymi
Quasar
Quelle
Seleco
Sencora
Sentra
Serino
Sharp
0210, 0211, 0215
0208
0218
Nordvision
Oceanic
Olevia
ONCEAS
Onwa
0060, 0061
0200
0201, 0207, 0210
0057, 0061, 0063,
0064
0204, 0205, 0214,
0215, 0217
0200, 0204, 0207
0060, 0061, 0063,
0102, 0103, 0150
0206, 0208
0009, 0010, 0011,
0060, 0061, 0066,
0070, 0087, 0111,
0143, 0145, 0167,
0168, 0169, 0198,
0204, 0224, 0247,
0248, 0249
0060
0204, 0205, 0215
0212
0255
0213
0058
LXI
Orbit
Orion
Magnadyne
Magnafon
Magnavox
Orline
Orsowe
Osaki
Radialva
Radio Shack
0204
0127, 0206, 0207,
0209, 0218
0201
0209, 0218
0218
Radio Shack/Realistic
0057, 0060, 0061,
Shogun
Siarem
Sicatel
Siemens
Sierra
Signature
Silva
Singer
Magnum
Majestic
Mandor
Manesth
0058
0206
Osio
Oso
Osume
0062, 0064
0213, 0217
Radiola
0206, 0207, 0213,
0217
0060, 0061, 0063,
0090, 0213, 0217
0205
0200, 0213, 0217
0204, 0207, 0208,
0210, 0213, 0217
0213, 0217
Radiomarelli
Radiotone
RCA
0204, 0205, 0214
0213
0057, 0060, 0061,
0091, 0133, 0135,
0147, 0149
0064
0213, 0217
0206, 0210, 0211
0203, 0205
0200
0213, 0217
0206, 0208, 0209,
0218, 0237
0205
0200
0205
0204, 0205, 0211,
0216
0212
0204, 0206, 0207,
0208
Otto Versand 0204, 0207, 0213,
0215, 0216, 0217,
0255
Pael
Palladium
Panama
Marantz
0200
0205, 0214, 0215
0204, 0205, 0215,
0217
0211
0211
0206, 0207, 0208,
0213, 0217
0211
0213, 0217
0041, 0059, 0067,
0085, 0086, 0174,
0196, 0199, 0208,
0219, 0234
Marelli
Mark
Matsui
0200, 0207
0207
0200, 0206, 0207,
0208
0006, 0007, 0063,
0073, 0074, 0097,
0110, 0114, 0137,
0141, 0151, 0162,
0165, 0186, 0204,
0211, 0244, 0245,
0246, 0254
Sinudyne
Realistic
Revox
Rex
Skantic
Solavox
Sonoko
Mediator
Medion
Megatron
Melectronic
Panasonic
RFT
0206, 0208
0061
Rhapsody
R-Line
Roadstar
Sonolor
Sontec
Sony
0200, 0207, 0208,
0211, 0213, 0216,
0217
0058, 0061, 0064,
0208
0208
0205
0060, 0061
0206, 0208
0206, 0208
0204
0213
0006, 0015, 0016,
0048, 0060, 0061,
0104, 0112, 0113,
0125, 0205, 0213
0200, 0201, 0202,
0203, 0204, 0207
Robotron
Rowa
RTF
Memorex
Pathe Cinema 0200, 0203, 0207,
0212, 0215
Pathe Marconi 0212, 0216
Pausa
Perdio
Philco
Memphis
Metz
MGA
Micromaxx
Microstar
Minerva
Minoka
Saba
Sound & Vision 0209, 0218
Soundesign
Soundwave
SSS
0060, 0061, 0062
0208
0200
0060, 0061, 0063,
0128, 0205, 0214,
0215
saccs
Saisho
0213, 0217
0060, 0062
0207, 0208, 0209,
0213, 0218
0217
Standard
Salora
0201, 0204, 0210,
0211, 0215
0204
0060, 0061, 0083,
0101
Starlight
Starlite
Stenway
Stern
Mitsubishi
Philharmonic 0207
Philips 0040, 0060, 0063,
Sambers
Sampo
0062
0218
0072, 0115, 0116,
0124, 0130, 0150,
0175, 0184, 0187,
0205, 0207, 0213,
0215, 0217, 0220,
0221, 0232, 0233,
0252, 0253
0210, 0211
0208, 0218
0208, 0213
0200, 0204, 0207
0200
0208
0059
0209
0208
0200, 0207
0060, 0061, 0063,
0080, 0134, 0142,
0148
0062, 0080
0217
Samsung
0029, 0030, 0031,
0032, 0044, 0045,
0046, 0047, 0060,
0061, 0065, 0068,
0069, 0071, 0079,
0087, 0127, 0128,
0130, 0144, 0160,
0161, 0170, 0176,
0183, 0185, 0200,
0201, 0206, 0207,
0208, 0213, 0217,
0239, 0241, 0242,
0243
Sunkai
Mivar
Sunwood
Superla
SuperTech
Supra
Supreme
Susumu
Sutron
Montgomery Ward
0058
MTC
0060, 0061, 0128,
0200
Philips Magnavox
0124
Phoenix
Multi System 0217
Multitech
0062, 0127, 0128,
0200, 0205, 0213,
0217
0200, 0205, 0213,
0217
Sydney
Sylvania
0200, 0207, 0208,
0210, 0214, 0215,
0217
0200, 0207
0061
Phonola
Murphy
NAD
Naonis
Pilot
Pioneer
0060
Symphonic
Sysline
Sytong
0012, 0013, 0060,
0061, 0098, 0109,
0117, 0128, 0181,
Sandra
Sansui
0200, 0207
0123, 0126, 0213
0210
0200
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Tandy
0127, 0207, 0209,
0211, 0218
0200, 0207, 0210
0127, 0204, 0207,
0213, 0217, 0237
0206, 0208
0127
0207, 0208, 0214,
0215
0060, 0061
0058, 0060, 0061,
0062
0216
0218
0065, 0213, 0216
0218
0208, 0214, 0217
0207
Weltblick
Weston
White Westinghouse
0200, 0207, 0217
0213, 0217
0215
Alba
1044, 1050
GoldHand
Goldstar
1050
1000, 1003, 1042,
1045
1042, 1045, 1050,
1069
1005
1043, 1047
1046, 1047, 1049
1042, 1045, 1050
1046, 1050, 1062
1045, 1046
American High 1004
Tashiko
Tatung
Amstrad
Anitech
ASA
Asha
Asuka
1042
1050
1045, 1046
1002, 1014
1042, 1045, 1046,
1050
Goodmans
Yamaha
0000, 0001, 0002,
0003, 0004, 0005,
0060, 0061
TCM
Teac
Tec
Gradiente
Graetz
Granada
Grandin
Grundig
Hanseatic
Harley Davidson1005
Harman/Kardon 1000
Harwood
HCM
Yamishi
Yoko
0218
0200, 0206, 0207,
0208, 0209, 0213,
0217, 0218
0209, 0218
0210
0058, 0060, 0100,
0105, 0119, 0121,
0154
Audio Dynamics1000
Audiovox
Baird
Basic Line
Baur
Beaumark
Techwood
Teknika
1003
1042, 1043, 1047
1044, 1050
1046
Yorx
Zanussi
Zenith
Teleavia
Telecor
Telefunken
Telegazi
Teletech
Teleton
1002, 1014
1006
1050
1001
1044, 1050
1044
1007, 1010, 1039,
1042, 1043, 1046,
1049
Bell & Howell 1001
Blaupunkt
Broksonic
Bush
1046, 1048
Headquarter
Hinari
Hisawa
Hitachi
1012, 1013
1044, 1050, 1066
1003
1002, 1003
1004
TV/DVD
Aiwa
Apex
Broksonic
Bush
Televideon
Tensai
0200
0208, 0209, 0213,
0218
0139, 2055
0132, 2049
0138, 2060
0230, 2112
0136, 2053
0137, 0254, 2054,
2110
0133, 0135, 2050,
2051
0134, 2052
0226, 2109
0131, 0231, 2048,
2111
Calix
Candle
Canon
CCE
Tesmet
Tevion
Texet
0213
1006
Hughes Network Systems
1010
Hypson
Imperial
Inno Hit
Innovation
0206, 0208
0200, 0207
0191, 0192, 0207,
0213, 0216, 0226
0212, 0217
0060, 0061
0213
0200, 0207
0027, 0043, 0053,
0054, 0064, 0078,
0089, 0090, 0106,
0107, 0127, 0131,
0140, 0146, 0159,
0197, 0225, 0231,
0237
0211, 0215
0200
0204
0218
0204
0211, 0213
0200, 0205, 0207,
0214, 0215
0217
0127, 0128, 0129,
0201, 0206, 0213,
0214, 0215, 0217
0212
0210, 0211, 0213,
0214, 0215, 0217
0208, 0217
0213
JVC
Panasonic
CGE
1042, 1043
1044, 1050
1002, 1003
1000
1006
1002, 1003, 1006,
1014
Cimline
Citizen
Colortyme
Colt
1044, 1050
1042
1046, 1050
1044, 1048
Thomson
RCA
Thorn
TMK
Tokai
Tokyo
Toshiba
Sylvania
Thomson
Toshiba
Craig
Instant Replay 1004
Interbuy
Interfunk
Intervision
Irradio
ITT
ITV
1045
1046, 1047
1042
1045, 1050
1043, 1047
1045
1000, 1001, 1002,
1003, 1004, 1006
1004
Crown
1050
Curtis Mathes 1000, 1002, 1004,
1009
Cybernex
Daewoo
TV/DVD/VCR
Panasonic
Samsung
Sharp
Sylvania
Toshiba
1002, 1014
1005, 1038, 1061,
1067
1050
1044
0141, 1040, 2057
0241, 1070, 2113
0143, 1028, 2059
0142, 1041, 2058
0140, 1029, 2056
JC Penney
Dansai
Dantax
DBX
De Graaf
Decca
Denon
Dimensia
Dual
JCL
Jensen
JVC
Towada
Transtec
Trident
Tristar
Triumph
Uher
1000
1007
1046, 1049
1042, 1043, 1046
1010
1000, 1001, 1007,
1011, 1017, 1036,
1043
1050
1046
TV/VCR
Aiwa
Bush
Daewoo
0237, 1066
0237, 1066
0155, 0238, 1038,
1067
1009
Kaisui
Karcher
Kendo
1043, 1046
1042, 1046, 1047,
1049
1005
1003
Ultravox
Dumont
1044
GE
0147, 1030
0240, 1069
0236, 1062
0156, 1039
0153, 1036
0150, 1033
0235, 1065
0151, 1034
0150, 0232, 0233,
1033, 1062, 1063
0152, 1035
0149, 1032
0237, 1066
0144, 0239, 1027,
1068
Kenwood
1000, 1001, 1007,
1011, 1043
1006
1003, 1004
1050
1050
1003, 1042, 1045,
1071
1044, 1048
1005
1048
1045, 1046
1006, 1050
1047
United
Universum
Goodmans
Grundig
Hitachi
JVC
Magnavox
Orion
Dynatech
Electrohome
Electrophonic 1003
Elta
KLH
Kodak
Korpel
Leyco
LG
1050
Univox
Vestel
Emerson
1003, 1004, 1005,
1012, 1013
1050
1043
1042
1046, 1047, 1049
1042, 1043, 1046,
1047, 1049
Panasonic
Philips
Etzuko
Vexa
Victor
Ferguson
Fidelity
Finlandia
Finlux
Lifetec
Lloyd's
Loewe
Loewe Opta
Logik
Luxor
LXI
M Electronic 1042
Magnasonic
Magnavox
Magnin
Manesth
Marantz
VIDEOLOGIC 0200
Videologique 0200, 0207, 0209,
0218
Videosat
VideoSystem 0213
Videotechnic 0200
Quasar
RCA
Roadstar
Samsung
0214
FIRST LINE 1044, 1045, 1049,
1050
Fisher
Flint
Formenti/Phoenix
1046
Fuji
Fujitsu
Funai
Galaxy
Garrard
GBC
1003
Sharp
Sony
Sylvania
Tatung
Toshiba
0145, 1028
0234, 1064
0148, 1031
0237, 1066
0146, 0237, 1029,
1066
1001, 1047
1044
Vidtech
Viewsonic
0060, 0061
1047
0076, 0077, 0092,
0099, 0172, 0173
0200, 0207
0213
0213, 0217
0205, 0210, 0211,
0213
0207, 0212
0057, 0058, 0060,
0061, 0063
0213, 0217, 0218
0200, 0207, 0212,
0215
1004, 1018, 1033
1003, 1014
1050
1000, 1001, 1004,
1046, 1051
1003
1044, 1045
1004
1046
Visiola
Vision
Vortec
Voxson
1004
1042
1005, 1042
1042
1005
Zenith
0154, 1037
Marta
VCR
Admiral
Adventura
Aiwa
Matsui
Matsushita
Mediator
Medion
MEI
Waltham
Wards
1008, 1013
1005
1005, 1042, 1043,
1044, 1066
1007, 1043
1050
1050
GE
1002, 1004, 1009,
1014, 1030
1046
1044, 1048
1004
Watson
Watt Radio
GEC
Geloso
General Technic 1044, 1048
Go Video 1014
Akai
Akiba
Akura
1050
Wega
0205
1043, 1050
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
UC
HTR-6140
The circled numbers and alphabets correspond to those in the Owner’s Manual.
Les nombres et lettres dans un cercle correspondent à ceux du mode d’emploi.
■ Front panel/Face avant
A
B
C
D
E
F
G H
I
VOLUME
STANDBY
/ON
OPTIMIZER MIC
EDIT
SEARCH MODE
PRESET/TUNING
CATEGORY
A/B/C/D/E
INFO
BAND
l
PRESET/TUNING/CH
h
MEMORY
TUNING AUTO/MAN'L
SCENE
1
2
3
4
VIDEO AUX
R
l
PROGRAM h
l
INPUT
h
VIDEO
L
AUDIO
PORTABLE
SPEAKERS
A/B/OFF
PHONES
TONE CONTROL
STRAIGHT
DIRECT
AUDIO SELECT
SILENT CINEMA
EFFECT
J
K
L
M
N
O
P
Q
Download from Www.Somanuals.com. All Manuals Search And Download.
■ Remote control/Boîtier de télécommande
1
POWER POWER
STANDBY
POWER
MUTE
H
I
2
3
TV
AV
A
XM
SIRIUS
J
K
CD
DVD
MD/CD-R TUNER
TV CH
DTV/CBL
B
DVR
C
4
V-AUX/DOCK
AMP
L
TV VOL
TV INPUT
TV MUTE
5
6
SCENE
1
2
3
4
M
N
O
SRCH MODE
MENU
BAND LEVEL
VOLUME
TITLE
7
8
9
ENTER
DISPLAY
RETURN
MEMORY
REC
0
A
INFO
P
Q
R
l
PROG h
ENHANCER SUR. DECODE
B
1
2
3
4
STRAIGHT DIRECT
5
NIGHT PARAMETER
C
D
E
F
6
7
8
S
t
MULTI CH IN AUDIO SEL
SLEEP
ENT
9
0
10
G
Printed in China
WN26230
Download from Www.Somanuals.com. All Manuals Search And Download.
|