RX-485 RDS/385/385 RDS
Natural Sound Stereo Receiver
Ampli-syntoniseur stéréo de la série “Natural Sound”
Natural Sound Stereoreceiver
Natural Sound Stereoreceiver
Ricevitore stereo a suono naturale
Receptor estéreo de Sonido Natural
Natural Sound Stereo Ontvanger
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
Download from Www.Somanuals.com. All Manuals Search And Download.
Thank you for selecting this YAMAHA stereo receiver.
FEATURES
●
●
●
RX-485 RDS
65W 65W (8Ω) RMS Output Power,
0.04% THD, 20 20,000 Hz
IF Count Direct PLL Synthesizer Tuning
System
+
–
Remote Control Capability
RX-385 and RX-385 RDS
+
RX-485 RDS and RX-385 RDS only
Multi-Functions for RDS Broadcast
Reception
40W 40W (8Ω) RMS Output Power,
●
–
0.04% THD, 20 20,000 Hz
●
High Dynamic Power, Low Impedance
Drive Capability
RX-485 RDS only
●
Pure Direct Switch to Reproduce the
Purest Source Sound
●
●
●
●
Continuously Variable Loudness Control
40-Station Random Preset Tuning
Automatic Preset Tuning
Preset Station Shifting Capability
CONTENTS
Supplied Accessories ......................................2
Remote Control Transmitter ..........................21
Caution ............................................................4
Connections ....................................................5
Operations .......................................................9
Tuning Operations .........................................12
Preset tuning .................................................13
Notes about the Remote Control
Transmitter ....................................................22
Troubleshooting .............................................23
Specifications ................................................24
Receiving RDS Stations
RX-485 RDS and RX-385 RDS only ..........16
How to Use This Manual
This manual describes three YAMAHA receivers, RX-385, RX-385 RDS and RX-485 RDS. There are some differences between
those three models. Especially, RX-385 RDS and RX-485 RDS contain the functions for receiving special data on RDS network
stations.
RX-385, on the other hand, is a receiver with a usual FM/AM tuning function.
Several places in the manual refer to differences in features between the three models. Be sure to follow the procedure for the
model you are using.
* RDS is a data transmitting service system in network which is employed by FM stations. RDS stations are increasing in many
countries (especially in Europe).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual
IMPORTANT
carefully. Keep it in a safe place for future reference.
Please record the serial number of this unit in the space below.
2. Install this unit in a cool, dry, clean place – away from windows,
heat sources, sources of excessive vibration, dust, moisture and
cold. Avoid sources of humming (transformers, motors). To
prevent fire or electrical shock, do not expose the unit to rain or
water.
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future reference.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
3. Never open the cabinet. If something drops into the set, contact
your dealer.
CAUTION (FOR CANADA MODEL)
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT AND FULLY INSERT.
4. Do not use force on switches, controls or connection wires. When
moving the unit, first disconnect the power plug and the wires
connected to other equipment. Never pull the wires themselves.
FOR CANADIAN CUSTOMER
THIS DIGITAL APPARATUS DOES NOT EXCEED THE “CLASS B”
LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS SET OUT IN THE RADIO INTERFERENCE
REGULATION OF THE CANADIAN DEPARTMENT OF
COMMUNICATIONS.
5. The openings on the cabinet assure proper ventilation of the unit.
If these openings are obstructed, the temperature inside the
cabinet will rise rapidly and eventually damage the circuits.
Therefore, avoid placing objects against these openings and do
not install the unit where the flow of air through the ventilation
openings could be impeded.
The apparatus is not disconnected from the AC power
source as long as it is connected to the wall outlet, even if
the apparatus itself is turned off.
6. Always set the VOLUME control to “– ” before starting the audio
∞
source play. Increase the volume gradually to an appropriate level
after playback has been started.
7. Do not attempt to clean the unit with chemical solvents; this might
For U.K. customers
damage the finish. Use a clean, dry cloth.
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the
instructions described below.
8. Be sure to read the “TROUBLESHOOTING” section regarding
common operating errors before concluding that the unit is faulty.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
9. When not planning to use this unit for long periods of time (ie.,
vacation, etc.), disconnect the AC power plug from the wall outlet.
10. To prevent lightning damage, disconnect the AC power plug and
SPECIAL INSTRUCTIONS FOR U.K. MODEL
disconnect the antenna cable when there is an electrical storm.
11. Grounding or polarization – Precautions should be taken so that
IMPORTANT:
the grounding or polarization of an appliance is not defeated.
The wire in the mains lead are coloured in accordance with
the following code:
12. AC outlet
Do not connect audio equipment to the AC outlet on the rear panel
if that equipment requires more power than the outlet is rated to
provide.
Blue: NEUTRAL
Brown: LIVE
The colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug. Proceed as follows: the wire
which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK. The
wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
13. Voltage Selector (General Model only)
The voltage selector on the rear panel of this unit must be set
for your local main voltage BEFORE plugging into the AC
main supply.
Voltages are 110/120/220/240V AC, 50/60 Hz.
FREQUENCY STEP switch (General Model only)
Because the interstation frequency spacing differs in different
areas, set the FREQUENCY STEP switch (located at the rear)
according to the frequency spacing in your area.
Before setting this switch, disconnect the AC power plug of this unit
from the AC outlet.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
ANTENNA CONNECTIONS
●
Each antenna should be connected to the designated terminals correctly, referring to the following figure.
Both AM and FM indoor antennas are included with this unit. In general, these antennas will probably provide sufficient signal
strength. Nevertheless, a properly installed outdoor antenna will give clearer reception than an indoor one. If you experience
poor reception quality, an outdoor antenna may result in improvement.
●
Outdoor FM antenna
Indoor FM
antenna
(included)
Outdoor AM antenna
AM loop
antenna
(included)
300-ohm
feeder
FM 75Ω
ANT UNBAL
GND
AM
ANT
75-ohm
75-ohm/300-ohm
coaxial cable antenna adapter
PHONO
CD
AUX
TAPE
PB
Ground
Connecting the AM loop antenna
➀
Orient so that the best
reception is obtained.
➂
➁
* The AM loop antenna should be placed apart from the main unit. The antenna may be hung on a wall.
* The AM loop antenna should be kept connected, even if an outdoor AM antenna is connected to this unit.
GND terminal
Notes
●
For maximum safety and minimum interference, connect the
GND terminal to a good earth ground. A good earth ground is
a metal stake driven into moist earth.
When connecting the indoor
FM antenna, make sure that
the grooved part of the
connector hole is facing
downward.
If you need an outdoor
●
FM antenna to improve
FM reception quality, either 300-ohm feeder or coaxial cable
may be used. In locations troubled by electrical
interference, coaxial cable is preferable.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before attempting to make any connections to or from this unit, be sure to first switch OFF the power to this unit and to any other
components to which connections are being made.
AUDIO CONNECTIONS
When making connections between this unit and other components, be sure all connections are made correctly, that is to say L
(left) to L, R (right) to R, “+” to “+” and “–” to “–”. Also, refer to the owner’s manual for each component to be connected to this unit.
RX-485 RDS
Speakers A
Tape deck 2
Video cassette player etc.
Right
Left
(Europe model)
FM 75Ω
ANT UNBAL
AC OUTLETS
GND
REMOTE
CONTR0L
SPEAKERS
AM
ANT
R
L
GND
A
B
A
B
PHONO
L
R
100W MAX. TOTAL
SWITCHED
TAPE 1
TAPE 2
PHONO
CD
AUX
TAPE
PB
REC
OUT
TAPE
PB
REC
OUT
To AC outlet
REMOTE CONTROL
Right
Left
Turntable
Compact disc player
Tape deck 1
Speakers B
*
: Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RX-385, RX-385 RDS
Speakers A
Video cassette player etc.
Right
Left
(Europe model)
FM 75Ω
ANT UNBAL
AC OUTLETS
GND
SPEAKERS
AM
ANT
R
L
A
B
A
L
GND
B
R
100W MAX. TOTAL
SWITCHED
TAPE 1
PHONO
CD
AUX
TAPE
PB
REC
OUT
To AC outlet
Right
Left
Turntable
Compact disc player
Tape deck
Speakers B
*
: Refer to “ABOUT THE ACCESSORY
TERMINALS” on page 8.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING SPEAKERS
Connect the SPEAKERS terminals to your speakers with wire
of the proper gauge, cut to be as short as possible. If the
connections are faulty, no sound will be heard from the
speakers. Make sure that the polarity of the speaker wires is
correct, that is, + and – markings are observed. If these wires
are reversed, the sound will be unnatural and will lack bass.
Do not let the bare speaker wires touch each other and do
not let them touch the metal parts of this unit as this could
damage this unit and/or speakers.
How to Connect:
Red: positive (+)
Black: negative (–)
➀
Press up the tab.
➀
➁
Insert the bare wire.
[Remove approx. 5mm
(1/4”) insulation from
the speaker wires.]
Press down the tab and
secure the wire.
●
One or two speaker systems can be connected to this unit.
➂
If you connect only one speaker system, connect it to either
the SPEAKERS A or B terminals.
Use speakers with the specified impedance shown on the
●
➂
➁
rear of this unit.
ABOUT THE ACCESSORY TERMINALS
AC OUTLET(S)
REMOTE CONTROL (PHONO) connector
(Europe model) ...................................2 SWITCHED OUTLETS
(U.K. model) ..........................................1 SWITCHED OUTLET
Use these to connect the power cords from your components
to this unit.
The power to the SWITCHED outlets is controlled by this unit’s
POWER switch or the provided remote control transmitter’s
POWER key. These outlets will supply power to any
component whenever this unit is turned on.
The maximum power (total power consumption of
components) that can be connected to the SWITCHED AC
OUTLET(S) is 100 watts.
RX-485 RDS only
If you have a YAMAHA turntable with a terminal for remote
control, connect it to this connector by using the cable provided
with the turntable. This connection allows you to control the
turntable from the provided remote control transmitter.
GND terminal (For turntable use)
Connecting the ground wire of the turntable to this terminal will
normally minimize hum, but in some cases better results may
be obtained with the ground wire disconnected.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
3
2
1, 6
7
4
TO PLAY A SOURCE
VOLUME
Select the speakers to be used.
1
4
SPEAKERS
A
B
ON
ON
OFF
OFF
0
—
dB
*
If you use two speaker systems, press both the A and B
switches.
Set to the “ ” position.
∞
POWER
Play the source. (For detailed information on the tuning
operations, refer to the page 12.)
5
6
2
3
VOLUME
Select a desired input source.
RX-485 RDS
MONITOR
INPUT
TUNER
TAPE 2
TAPE 1
AUX
CD
PHONO
0
—
dB
COPY
Adjust to the desired output level.
RX-385, RX-385 RDS
INPUT
TUNER
If desired, adjust the BASS, TREBLE, BALANCE and
LOUDNESS controls, etc. (Refer to page 11.)
TAPE
7
MONITOR
AUX
CD
PHONO
Notes
RX-485 RDS only
*
*
The name of the selected input source will appear in the
display.
Note that pressing on each input selector button selects
the source which is connected to the corresponding input
terminals on the rear panel.
●
If you select AUX, TUNER, CD or PHONO, be sure that
TAPE 1 and/or TAPE 2 are not being selected.
If you select TAPE 1 and TAPE 2 at the same time, the
result will be the sound from the tape deck 1.
For TAPE 1 and TAPE 2, whenever the button is pressed,
the corresponding input source is selected or canceled
alternately.
●
●
RX-385 and RX-385 RDS only
●
If both TAPE MONITOR and another input selector button
are selected, TAPE MONITOR has priority.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
1, 4
2
TO RECORD A SOURCE TO TAPE
RX-485 RDS
TO RECORD A SOURCE TO TAPE
RX-385, RX-385 RDS
1
1
Select the source to be recorded.
Select the source to be recorded.
MONITOR
TAPE 2 TAPE 1
INPUT
TUNER
INPUT
TUNER
TAPE
MONITOR
AUX
CD
PHONO
AUX
CD
PHONO
COPY
*
*
To dub from tape to tape, refer to the “Notes” shown
below.
When you select AUX, TUNER, CD or PHONO, be sure
that TAPE 1 and/or TAPE 2 are not also selected.
*
When you select AUX, TUNER, CD or PHONO, be sure
that TAPE MONITOR is not also selected.
2
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 12.)
2
Play the source and then turn the VOLUME control up
to confirm the input source. (For detailed information
on the tuning operations, refer to the page 12.)
3
4
Begin recording on the tape deck.
3
4
Begin recording on the tape deck.
To monitor the audio signals being recorded, press the
TAPE MONITOR.
To monitor the audio signals being recorded, press the
input selector button for the tape deck being used to
make the recording.
INPUT
TUNER
TAPE
MONITOR
AUX
CD
PHONO
MONITOR
TAPE 2 TAPE 1
INPUT
TUNER
AUX
CD
PHONO
COPY
Note
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being recorded.
Notes
●
VOLUME, BASS, TREBLE, BALANCE and LOUDNESS
control settings have no effect on the material being
recorded.
●
To dub from tape to tape, only the following method of
dubbing can be performed.
RECORDER
SOURCE
Tape deck connected to
the TAPE 1 terminals.
Tape deck connected to
the TAPE 2 terminals.
→
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the BALANCE control
Selecting the SPEAKER system
Adjust the balance of the output volume to the left and right
speakers to compensate for sound imbalance caused from
speaker location or listening room conditions.
Because one or two speaker systems can be connected to this
unit, the SPEAKERS switches allow you to select speaker
system A or B, or both at once.
BALANCE
SPEAKERS
0
A
B
ON
ON
OFF
OFF
L5
5R
Adjusting the BASS and TREBLE
controls
Adjusting the continuously variable
LOUDNESS control
This control provides compensation for the human ears’ loss of
sensitivity to high and low-frequency ranges at low volume.
This control is adjustable to retain full tonal range at any
volume level.
TREBLE
BASS
DEFEAT
DEFEAT
1
LOUDNESS
5
5
—
5+
—
5+
FLAT
—
30dB
I0
Set to the “FLAT” position.
BASS
: Turn this clockwise to increase (or counter-
clockwise to decrease) the low frequency
response.
2
VOLUME
TREBLE : Turn this clockwise to increase (or counter-
clockwise to decrease) the high frequency
response.
Set to the loudest listening level that
you would listen to.
0
—
dB
3
LOUDNESS
Turn so that the desired volume can
be achieved.
FLAT
—
30dB
I0
Using the PURE DIRECT switch
RX-485 RDS only
You can enjoy the purest possible sound from your audio
sources by setting this switch ON. By doing so, the audio
signal bypasses the BASS, TREBLE, BALANCE and
LOUDNESS controls, eliminating any alterations to the audio
signal.
When you listen with headphones
Connect the headphones to the PHONES jack. When listening
with headphones privately, set both the SPEAKERS A and B
switches to the OFF position.
PHONES
PURE DIRECT
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TUNING OPERATIONS
Normally, if station signals are strong and there is no interference, quick automatic-search tuning (AUTOMATIC TUNING) is
possible. However, if signals of the station you want to select are weak, you must tune to it manually (MANUAL TUNING).
3
2
1
AUTOMATIC TUNING
MANUAL TUNING
1
Select the reception band (FM or AM) while watching
the display.
1
Select the reception band (FM or AM) while watching
the display.
FM/AM
FM/AM
or
AM
AM
FM
FM
or
TUNING
MODE
TUNING
MODE
2
3
2
3
“AUTO TUNING”
goes off.
AUTO TUNING
AUTO/
M’L MONO
AUTO/
MAL MONO
DOWN
TUNING
UP
Tune to a desired station manually.
DOWN
TUNING
UP
To tune to a higher frequency, press the right side once.
To tune to a lower frequency, press the left side once.
* If the station where tuning search stopped is not the
desired one, press again.
* To continue tuning search, press and hold the button.
* If the tuning search does not stop at the desired station
(because the signals of the station are weak), change to
the MANUAL TUNING method.
Note
If you tune to an FM station manually, it is received in
monaural mode automatically to increase the signal quality.
Display information
RX-385
Displays the band and frequency of the received station.
RX-485 RDS and RX-385 RDS only
If an RDS station is received, the frequency is then
replaced by the station name. (However, if the PS data
cannot be received within 5 seconds, “NO PS” flashes,
and then it returns to the frequency display.)
Refer to page 17 for details.
Illuminates when an FM stereo broadcast is received in
stereo.
Indicates the signal level of the received station.
➀
➀
➁
STEREO
➂
➂
FM
MHz
0
20 40 60
l00
➁
➂
RX-485 RDS, RX-385 RDS
➀
➁
STEREO
FM
MHz
0
20
l00
12
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESET TUNING
MANUAL PRESET TUNING
This unit can store station frequencies selected by tuning operation. With this function, you can recall any desired station by only
selecting the preset station number where it is stored. Up to 40 stations (8 stations x 5 pages) can be stored.
3, 1
2, 5
4, 2
To store stations
To recall a preset station
1
2
Tune to a desired station.
(Refer to the previous page for tuning procedures.)
1
Select the page where the preset station is stored.
A/B/C/D/E
PRESET
FM
MEMORY
PRESET
MEMORY
FM
MEMORY
MAN’L/O FM
2
PRESET
Flashes on and off
for about 5 seconds.
DOWN STATIONS
UP
3
4
Select a desired page (A – E) of preset stations while
watching the display.
A/B/C/D/E
Select the preset station number.
PRESET
FM
MEMORY
Notes
●
A new setting can be programmed in place of the former
one.
For presets, the setting of the reception mode (stereo or
monaural) is stored along with the station frequency.
●
Select a preset station number (1–8) while watching the
display before “MEMORY” goes off from the display.
PRESET
Memory back-up
DOWN STATIONS
UP
The memory back-up circuit prevents the programmed data
from being lost even if the POWER switch is set off or the
power plug is disconnected from the AC outlet or the power is
cut due to temporary power failure. If, however, the power is
cut for more than one week, the memory may be erased. If so,
it can be re-programmed by simply following the PRESET
TUNING steps.
RX-385
5
PRESET
STEREO
FM
20 40 60
MHz
0
l00
MEMORY
AUTO TUNING
Shows the displayed station
has been programmed to A1.
MAN’L/O FM
RX-485 RDS, RX-385 RDS
PRESET
STEREO
20
FM
MHz
0
l00
AUTO TUNING
Shows the displayed station
has been programmed to A1.
* In the same way, program other stations to A2, A3 ... A8.
* You can program more stations on other pages in the
same way by selecting other pages in step 3.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC PRESET TUNING
You can also make use of an automatic preset tuning function for FM stations only. By this function, this unit performs automatic
tuning and stores FM stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the
manual preset tuning method on page 13.
RX-485 RDS and RX-385 RDS only
* Only RDS stations can be stored by this function.
2
1
To store stations
When the automatic preset tuning is finished
The display shows the frequency of the last preset station.
1
FM/AM
Check the contents and the number of preset stations by
following the procedure of the section “To recall a preset
station” on page 13.
FM
To recall a preset station
Simply follow the procedure of the section “To recall a preset
station” on page 13.
RX-485 RDS and RX-385 RDS only
* A recalled station is shown by the frequency or station name
on the display.
2
MEMORY
Press and
hold for about
3 seconds.
MAN’L/O FM
Notes
●
You can replace a preset station by another FM or AM
station manually by simply following the procedure of the
section “To store stations” on page 13.
RX-385 only
PRESET
●
AUTO TUNING
If the number of received stations is not enough to be stored
and
MEMORY
up to E8, the search is finished automatically when it
reaches the highest frequency after searching through all
frequencies.
Flashes.
Flashes.
●
With this function, only FM stations with sufficient signal
strength are stored automatically. If the station you want to
program is week in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 13.
RX-485 RDS and RX-385 RDS only
The automatic preset tuning search will be performed
through all RDS network frequencies until stations are
stored up to E8. If the number of received stations is not
enough to be stored up to E8, the search is finished
automatically after searching through all frequencies.
After 5 seconds, the automatic preset tuning begins from A1.
Received stations are programmed to A1, A2 ... A8
sequentially.
* If more than 8 stations are received, they are also
programmed to the preset station numbers on other pages
(B, C, D and E) in that order.
●
If you want to store the first station received by the
automatic preset tuning to a desired preset station
number.
If, for example, you want to store the received first station to
C5, select “C5” by using the A/B/C/D/E button and the
PRESET STATIONS button soon after the display begins
flashing on/off in step 2. After a few seconds, the automatic
preset tuning begins. The received first station is stored to C5,
and next stations to C6, C7 ... sequentially.
●
With this function, only RDS stations with sufficient signal
strength are stored automatically. If the station you want to
program is weak in signal strength, tune to it in monaural
manually and program it by following the procedure of the
section “To store stations” on page 13.
* There may be a case that this function cannot receive a
station which could be received by the automatic tuning
method. This is because this function receives a large
volume of PI (Program Identification) data along with the
station.
If stations are stored up to E8, the automatic preset tuning is
finished automatically.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXCHANGING PRESET STATIONS
You can exchange the places of two preset stations each other by easy operations.
2, 4
Example)
If you want to shift the preset station on E1 to A5, and vice
versa.
1
2
Recall the preset station on E1 (by following the method
of “To recall a preset station” on page 13).
4
EDIT
EDIT
Flashes
3
Next, recall the preset station on A5 by following the
same method with step 1.
Shows the exchange of stations is completed.
Flashes
15
Download from Www.Somanuals.com. All Manuals Search And Download.
RECEIVING RDS STATIONS
RX-485 RDS and RX-385 RDS only
RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations
using this system transmit an inaudible stream of data in addition to the normal radio signal.
RDS data contains various information, such as AF (Alternative Frequencies for the same program station), PI (Program
Identification), PS (Program Service station name), PTY (Program Type name), etc.
RDS function is carried out among the network stations.
* This unit utilizes AF, PI, PS and PTY to receive RDS broadcast stations.
Displaying RDS data
This unit can be turned into the following two modes to display RDS data.
PS (Program Service station name) mode:
BBC R3
Displays the name of the RDS station now being received instead of the frequency.
PTY (Program Type name) mode:
Displays the program type of the RDS station now being received. There are 15 program types to classify RDS stations as follows.
News:
Varied:
Short accounts of facts, events and publicly
expressed views, reportage and actuality.
Used for mainly speech-based programs
usually of light-entertainment nature, not
covered by above categories. Examples are:
quizzes, panel games, personality interviews,
comedy and satire.
NEWS
VARIED
Current affairs:
Topical program expanding or enlarging
upon the news, generally in different
presentation style or concept, including
documentary debate, or analysis
AFFAIRS
Pop:
Commercial music, which would generally be
considered to be of current popular appeal,
often featuring in current or recent record
sales charts.
POP M
Information:
Program whose purpose is to impart advice
in the widest sense, including meteorological
reports and forecasts, consumer affairs,
medical help, etc.
INFO
Rock:
Contemporary modern music, usually written
and performed by young musicians.
ROCK M
MOR M
Sport:
Program concerned with any aspect of sport.
M.O.R.:
SPORT
(Middle of the Road Music). Common term to
describe music considered to be “easy-
listening”, as opposed to Pop, Rock or
Classical. Music in this category is often but
not always, vocal, and usually of short
duration (<5 min.)
Education:
EDUCATE Program intended primarily to educate, of
which the formal element is fundamental.
Light classics:
Classical Musical for general, rather than
specialist appreciation. Examples of music in
this category are instrumental music, and
vocal or choral works.
Drama:
All radio plays and serials.
LIGHT M
DRAMA
Serious classics:
Culture:
CLASSICS Performances of major orchestral works,
Programs concerned with any aspect of
national or regional culture, including
symphonies, chamber music etc., and
CULTURE
including Grand Opera.
religious affairs, philosophy, social science,
language, theatre, etc.
Other music:
Musical styles not fitting into any of the
above categories. Particularly used for
specialist music, of which Jazz, Rhythm &
Blues, Folk, Country, and Reggae are
examples.
Science:
OTHER M
Programs about the natural sciences and
technology.
SCIENCE
16
Download from Www.Somanuals.com. All Manuals Search And Download.
To turn the unit into the PS mode or PTY mode
Press the FREQ/PS/PTY button. Whenever pressed, the mode changes into the PS mode, PTY mode and returns to usual mode in
turn.
* When an RDS station is received, the display is automatically turned into the PS mode. Do not press the FREQ/PS/PTY button
until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that “NO
PS” flashes on the display. This is because the unit has not received all of the RDS data on the station yet.
PS mode
The name of the station being received is displayed.
If the station is not an RDS station, “NO PS” flashes on the
display and then returns to usual mode.
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
PTY mode
A program type for the station being received is displayed.
If the RDS station does not employ the PTY data service,
“NO PTY” flashes on the display and then returns to the PS
mode.
If the station is not an RDS station, “NO PTY” flashes on the
display and then returns to usual mode.
Usual mode
The frequency of the station being received is displayed.
Note
When PS or PTY data reception is not possible due to poor reception conditions, “NO PS” or “NO PTY” flashes on the display in
each mode. In such a case, press the TUNING MODE button so that “AUTO TUNING” goes off from the display. Though the
reception mode is changed to monaural by this operation, when you changes to the PS or PTY mode, PS or PTY data may be
displayed.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Calling a preset RDS station by the station name (PS SEEK)
You can call a desired RDS station stored in this unit by only inputting the name of the station in the PS mode. By this operation,
this unit searches all preset stations for the station. You do not have to input a full name, even only the first letter can be used for
calling. As many as 8 letters and/or numerals can be selected for inputting a name.
2, 3, 5, 7
4 8
1
FM/AM
1
2
6
7
Repeat steps 4 and 5 for other letters and/or numerals,
if necessary.
FM
When inputting the name is finished, press the ENTER
Turn the unit into the PS mode.
PS/PTY SEEK
button.
FREQ/PS/PTY
SHIFT
ENTER
A station name
is displayed or
“NO PS” flashes.
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
ENTER
* If “NO PS” flashes, proceed to the next step while flashing.
If “NO PS” disappears before you proceed to the next step,
press the FREQ/PS/PTY button again.
Flashes.
8
PRESET
PS/PTY SEEK
DOWN STATIONS
UP
3
FREQ/PS/PTY
SHIFT
ENTER
Press once.
Flashes.
Select the first letter or numeral of the station name.
The unit begins searching for the station, and it is
continued until the station is found.
4
DOWN
TUNING
UP
You do not have to input a full name for searching
for the station
You may input only the first letter of the station name. If doing
so, you can skip steps 5 and 6. In step 8, the unit searches
for and calls a nearest station which has the letter you input. If
the station is not the desired one, press the PRESET
STATIONS button again. The unit will begin searching for
another station which has the same letter.
* By pressing the TUNING button repeatedly or by pressing
and holding it, the display will change letters and numerals
in sequence.
* If you will not input the second letter, skip to step 7.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or
MEMORY button.
5
When the first letter or numeral of the station name
appears, press the SHIFT button to proceed to the
selection of the next letter or numeral.
Notes
●
If no station is found by this function after searching all
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
preset stations, “NO PS” flashes for about 3 seconds on
the display, and then it returns to the mode which had
been obtained before the searching was performed.
●
This function is useful especially for calling a station with
“A” will flash on the second
letter or numeral position.
weak signals which cannot be received by the automatic
tuning method. By only storing such a station, you can call
it any time easily.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Calling a preset RDS station by the program type (PTY SEEK)
By designating a program type, the unit automatically searches all preset stations for RDS stations of that program type.
* There are 15 program types to classify RDS stations. For details, refer to page 16.
3 5
1, 2, 4
1
Turn the unit into the PTY mode.
4
When the desired program type appears, press the
ENTER button.
PS/PTY SEEK
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
FREQ/PS/PTY
SHIFT
ENTER
Press once or twice until a
program type is displayed
or “NO PTY” flashes.
ENTER
Flashes.
* If “NO PTY” flashes, proceed to the next step while
flashing. If “NO PTY” disappears before you proceed to the
next step, press the FREQ/PS/PTY button once or twice.
5
PRESET
DOWN STATIONS
UP
Press once.
2
PS/PTY SEEK
FREQ/PS/PTY
SHIFT
ENTER
The unit begins searching all preset stations, and calls a
station of the program type if such a station is found.
The program type of the station now being
received or “NEWS” flashes on the display.
* When the right side of the PRESET STATIONS button is
pressed, the search is performed from “A1” toward higher
numbers of the preset stations (A1, A2 ... A8, B1, B2, ...).
If, however, “A3” is currently being called for example, the
search begins from the next station “A4”.
3
Select the desired program type.
DOWN
TUNING
UP
When the left side of the PRESET STATIONS button is
pressed, the search is performed in reverse order.
If the called station is not the desired one, press the
PRESET STATIONS button again to search for another
station of the same program type.
* By pressing the TUNING button repeatedly or by pressing
and holding it, the display will change program types in
sequence.
To cancel this function
Press the AF, FREQ/PS/PTY, SHIFT, ENTER, FM/AM or
MEMORY button.
Note
If no station is found by this function, after searching all preset
stations, “NO PTY” flashes for about 3 seconds on the
display, and then it returns to the mode which had been
obtained before the searching was performed.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Calling the best quality RDS station which broadcasts the
same program (AF SEEK)
This function automatically searches for and calls another RDS station of the best reception quality which broadcasts the same
program now you are listening to.
This function utilizes AF (Alternative Frequencies for the same program station) and PI (Program Identification) of RDS data service.
The search is carried out among the RDS network stations.
2, 3
1
2
Tune to a desired RDS station.
3
If desired, you can call the second station by pressing
* Wait for about 10 seconds before proceeding to the
next step. This is for making this unit carry out
searching more stations.
the AF button.
AF
AF
Whenever the AF button is pressed, stored stations are
called in sequence.
When pressed after the last station is selected, the first one
is restored.
The unit searches network stations for other stations with
the same program.
* If the station is not an RDS station, or there is no other
station with the same program, “NO AF” flashes.
To cancel this function
Press a button other than the AF button.
All of the stored stations will be also cleared.
Stations with the same program are all stored and
numbered from the best quality station in sequence.
When the search is finished, the best quality station is
called.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL TRANSMITTER
The remote control transmitter provided with this unit is designed to control all the most commonly used functions of the unit. If the
CD player, turntable and tape deck connected to this unit are YAMAHA components, then this remote control transmitter will also
control various functions of each component.
KEY FUNCTIONS
For Control of This Unit
The power to the receiver is automatically
POWER
SLEEP
PLAY/CUT
PLAY
PHONO
CD
turned off one hour after this key is
pressed (so that “SLEEP” illuminates on
the display).
Turns the power on/off.
SKIP
SEARCH
PAUSE/STOP
DISC SKIP
—
PRESET
+
DECK A/B
PLAY
STOP
A/B/C/D/E TUNER
Selects preset station number
+ : Selects higher preset station number.
– : Selects lower preset station number.
A/B/C/D/E: Selects the page (A – E) of
preset stations.
DIR A
DIR B
TAPE 1
TAPE 2
Selects input source.
REC/PAUSE
REC MUTE
AUX
—
+
VOLUME
Turns the volume level up/down.
For Other Component Control
Identify the remote control transmitter keys with your component’s keys. If these keys are identical, their function will be the
same. On each key function, refer to the corresponding instruction on your component’s manual.
Controls compact disc player.
Starts/stops record play on turntable.
POWER
SLEEP
PLAY/CUT
PLAY
PHONO
CD
*
DISC SKIP is applicable only to
compact disc changer.
SKIP
SEARCH
PAUSE/STOP
DISC SKIP
—
PRESET
+
DECK A/B
PLAY
STOP
A/B/C/D/E TUNER
Controls tape deck.
DIR A
DIR B
TAPE 1
TAPE 2
*
DIR A, B and DECK A/B are
applicable only to double
cassette tape deck.
*
For a single cassette deck with
automatic reverse function,
pressing DIR A will reverse the
direction of tape running.
REC/PAUSE
REC MUTE
AUX
—
+
VOLUME
Illustrations : RX-485 RDS
* PLAY/CUT is equipped only on RX-485 RDS.
* TAPE 1 and TAPE 2 are equipped only on RX-485 RDS. On RX-385 and RX-385 RDS, they are replaced by TAPE only.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDBY mode (Europe model only)
While the power is on, pressing the POWER key on the remote
control transmitter switches the unit to the STANDBY mode.
(In this mode, the standby indicator on the front panel is half
illuminated.)
STANDBY mode
POWER on mode
NOTES ABOUT THE REMOTE CONTROL TRANSMITTER
Battery installation
Remote control transmitter operation range
2
Remote control
sensor
1
3
Within approximately
7 m (23 feet)
Battery replacement
If you find that the remote control transmitter must be used
closer to the main unit, the batteries are weak. Replace both
batteries with new ones.
Notes
●
Use only AA, R6, UM-3 batteries for replacement.
Be sure the polarities are correct. (See the illustration inside
●
the battery compartment.)
Remove the batteries if the remote control transmitter will
●
Notes
●
not be used for an extended period of time.
There should be no large obstacles between the remote
control transmitter and the main unit.
If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp etc.),
it might cause the remote control transmitter not to work
correctly. In this case, reposition the main unit to avoid
direct lighting.
●
If batteries leak, dispose of them immediately. Avoid
touching the leaked material or letting it come in contact with
clothing, etc. Clean the battery compartment thoroughly
before installing new batteries.
●
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If the unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple
measures suggested. If it cannot be corrected, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and
contact your authorized YAMAHA dealer or service center for help.
SYMPTOM
CAUSE
REMEDY
The unit fails to turn on when the POWER
switch is pressed.
Power cord is not plugged in or is not completely
inserted.
Firmly plug in the power cord.
No sound.
Incorrect output cord connections.
Connect the cords properly. If the problem persists,
the cords may be defective.
Appropriate input selector button is not pressed.
Press the appropriate input selector button
corresponding to the input source.
The sound suddenly goes off.
The protection circuit has activated because of
short circuit etc.
Turning the unit off and then on will reset the
protection circuit.
Only one side speaker outputs the sound.
Incorrect setting of the BALANCE control
Incorrect cord connection.
Adjust it to the appropriate position.
Connect the cord properly. If the problem persists,
the cables may be defective.
Sound “hums”.
Incorrect cord connections.
Firmly connect the audio plugs. If the problem
persists, the cord may be defective.
No connection from the turntable to the GND
terminal.
Make the GND connection between the turntable
and this unit.
The volume level is low while playing a record.
The record is being played on a turntable with an
MC cartridge.
The player should be connected to the receiver
through the MC head amplifier.
The volume level cannot be increased, or
sound is distorted.
The power to the component connected to the REC
OUT terminals of this unit is off.
Turn the power to the component on.
FM stereo reception is noisy.
Because of the characteristics of FM stereo
broadcasts, this is limited to cases where the
transmitter is too far or the antenna input is poor.
Check the antenna connections.
Try using a multiple element FM antenna.
There is distortion and clear reception cannot
be obtained even with a good FM antenna.
There is multipath interference.
Adjust antenna placement to eliminate multipath
interference.
A desired station cannot be tuned in with Auto
tuning.
The station is too weak.
Use Manual tuning mode.
Use high quality directional FM antenna.
A desired station cannot be tuned in with Auto
tuning.
Weak signal or loose antenna connections.
Use Manual tuning mode.
Tighten the AM loop antenna connections and
rotate it for best reception.
There are continuous crackling and hissing
noises.
Noises will result from ligtning, fluorescent lamps,
motors, thermostats and other electrical equipment.
Use an outdoor antenna and a ground wire. This
will help somewhat but it is difficult to eliminate all
noises.
There are buzzing and whining noises
(especially in the evening).
A television set is being used nearby.
Relocate this unit away from the TV.
The remote control transmitter does not work.
Direct sunlight or lighting (of an inverter type of
flourescent lamp etc.) is striking the remote control
sensor of the main unit.
Change position of the main unit.
The batteries of this remote control transmitter are
too weak.
Replace the batteries with new ones.
Turn the power to this unit on.
The sound is degraded when monitoring is
performed by using the headphones connected
to the compact disc player or cassette deck
which are connected with this unit.
The power to this unit is off.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
AUDIO SECTION
FM SECTION
<RX-385 RDS>
Minimum RMS Output Power per Channel
8 ohms, 20 Hz to 20 kHz, 0.04% THD
<RX-485 RDS>............................65W+65W
<RX-385/385 RDS>
Tuning Range
[Except Europe and U.K. models]
(1 kHz)...................................................50 dB
[Europe and U.K. models]
[U.S.A., Canada and General models]
........................................87.5 to 107.9 MHz
[Australia, Europe, U.K. and General
models] ...........................87.5 to 108.0 MHz
50 dB Quieting Sensitivity (IHF, 75 ohms)
<RX-485 RDS/385>
(40 kHz Dev.) ........................................50 dB
Frequency Response
20 Hz to 15 kHz...............................0 ±1.5 dB
[U.S.A. and Canada models].......45W+45W
[Australia, U.K., Europe and
General models]..........................40W+40W
6 ohms, 20 Hz to 20 kHz, 0.06% THD
<RX-485 RDS>............................70W+70W
<RX-385/385 RDS>
[Except Europe model]
AM SECTION
Tuning Range
Mono...............................1.55 µV (15.1 dBf)
Stereo ................................21 µV (37.7 dBf)
<RX-385 RDS>
[U.S.A., Canada and General models]
..........................................530 to 1,710 kHz
[Australia, U.K., Europe and General
models] .............................531 to 1,611 kHz
Usable Sensitivity ..............................100 µV/m
Selectivity.................................................32 dB
Signal-to-Noise Ratio...............................50 dB
Image Response Ratio ............................40 dB
Spurious Response Ratio ........................50 dB
Harmonic Distortion...................................0.3%
[U.S.A. and Canada models].......48W+48W
Dynamic Power per Channel
Mono...............................1.55 µV (15.1 dBf)
Stereo ................................21 µV (37.7 dBf)
Usable Sensitivity (75 ohms)
(by IHF Dynamic Headroom measuring
method)
<RX-485 RDS>
<(R3X0-d4B85SR/NDQS/u3i8e5tin>g, 1 kHz, 100% mod.)
<8R/X6/-43/825o/3h8m5sR..D...S..>.............95/115/135/150W
[U.S.A., Canada and General models]
8/6/4/2 ohms..........................69/78/90/98W
[Australia, Europe and U.K. models]
8/6/4/2 ohms..........................68/75/85/95W
DIN Standard Output Power per Channel
4 ohms, 1 kHz, 0.7% THD
[Except Europe model]
............................................0.8 µV (9.3 dBf)
DIN, Mono (S/N 26 dB) [Europe model]
.............................................................0.9 µV
DIN, Stereo (S/N 46 dB) [Europe model]
..............................................................24 µV
<RX-385 RDS>
AUDIO SECTION
Output Level/Impedance
<RX-485 RDS/385>
<[REXu-r4o8p5e RmDodSe>l .o..n..ly..]...............................85W
<RX-385/385 RDS>...............................55W
IEC Power
[Except Europe and U.K. models]
............................................0.8 µV (9.3 dBf)
DIN, Mono (S/N 26 dB)
FM (100% mod., 1 kHz)
[Except Europe model]
......................................500 mV/2.2 k-ohms
[Europe model (40 kHz Dev.)]
......................................400 mV/2.2 k-ohms
AM (30% mod., 400 Hz)
[Europe and U.K. models] .................0.9 µV
DIN, Stereo (S/N 46 dB)
[Europe and U.K. models] ..................24 µV
Image Response Ratio
<RX-485 RDS>
8 ohms, 1 kHz, 0.04% THD
[Europe model only]..............................75W
<RX-385/385 RDS>
<.R..X...-.3..8..5...R...D..S...>...................150 mV/2.2 k-ohms
<RX-485 RDS/385>
8 ohms, 1 kHz, 0.04% THD
[Except Europe and U.K. models].......45 dB
[Europe model] ...................................80 dB
<RX-385 RDS>
FM (100% mod., 1 kHz)
[Europe model only]..............................50W
Damping Factor
8 ohms, 20 Hz to 20 kHz ............................80
Input Sensitivity/Impedance
[Except Europe and U.K. models]
......................................500 mV/2.2 k-ohms
[Europe and U.K. models (40 kHz Dev.)]
......................................400 mV/2.2 k-ohms
AM (30% mod., 400 Hz)
[Except Europeand U.K. models]........45 dB
[Europe and U.K. models]...................80 dB
IF Response Ratio ...................................80 dB
Spurious Response Ratio ........................70 dB
AM Suppression Ratio .............................55 dB
Capture Ratio..........................................1.5 dB
Alternate Channel Selectivity
PHONO MM ......................2.5 mV/47 k-ohms
CD/TAPE/AUX..................150 mV/47 k-ohms
Maximum Input Signal (1 kHz, 0.01% THD)
PHONO MM .........................................80 mV
Headphone Jack Rated Output/Impedance
8 ohms, 20 Hz to 20 kHz, 0.04% THD
Output Level
<RX-485 RDS>....................................0.46V
<RX-385/385 RDS>.............................0.45V
Impedance
<RX-485 RDS> .............................390 ohms
<RX-385/385 RDS> ......................330 ohms
Frequency Response (20 Hz to 20 kHz)
CD/TAPE/AUX..................................0±0.5 dB
RIAA Equalization Deviation
PHONO MM.....................................0±0.5 dB
Total Harmonic Distortion (20 Hz to 20 kHz)
PHONO MM to REC OUT (1V) ............0.02%
CD/TAPE/AUX to SP OUT
.........................................150 mV/2.2 k-ohms
GENERAL
Power Supply
<RX-485 RDS/385>
[U.S.A. and Canada models]
...........................................AC 120V, 60 Hz
[Australia and U.K. models]
...........................................AC 240V, 50 Hz
[Europe model]...................AC 230V, 50 Hz
[General model]
[Except Europe model] .......................85 dB
<RX-385 RDS>
[Except Europe and U.K. models].......85 dB
Selectivity (two signals, 40 kHz Dev.)
<RX-485 RDS/385>
[Europe model] ...................................70 dB
<RX-385 RDS>
.................AC 110/120/220/240V, 50/60 Hz
Power Consumption
[Europe and U.K. models]...................70 dB
Signal-to-Noise Ratio
<RX-485 RDS>
[U.S.A. model].....................................155W
[Canada model].....................250 VA, 205W
[Europe, Australia and General models]
<RX-485 RDS/385>
(IHF) Mono/Stereo
[Except Europe model].............80 dB/75 dB
(DIN-Weighted, 40 kHz Dev.) Mono/Stereo
[Europe model].........................74 dB/69 dB
<RX-385 RDS>
<.R..X...-.3..8..5../.3..8..5...R..D...S..>................................135W
[Canada model] ..................................170W
[U.S.A., Australia, Europe, U.K. and
General models] .................................120W
AC Outlets
2 SWITCHED OUTLETS
[U.S.A., Canada, Europe and
General models].................100W max. total
1 SWITCHED OUTLET
[Australia and U.K. models]
...........................................100W max. total
Dimensions (W x H x D)
..........................................435 x 126 x 298 mm
(17-1/8” x 4-15/16” x 11-3/4”)
W<eiRgXht-485 RDS>.............7.0 kg (15 lbs. 6 oz.)
<RX-385/385 RDS>......6.1 kg (13 lbs. 7 oz.)
Accessories............................AM loop antenna
Indoor FM antenna
<RX-485 RDS>
(32.5W/8 ohms)....................................0.02%
<RX-385/385 RDS>
(IHF) Mono/Stereo
(22.5W/8 ohms)....................................0.02%
Signal-to-Noise Ratio (IHF-A Network)
PHONO MM (5 mV Input Shorted)........82 dB
CD/TAPE/AUX (Input Shorted) ...........105 dB
Residual Noise (IHF-A Network)............100 µV
Channel Separation (Vol. –30 dB)
PHONO MM (Input Shorted 1 kHz).......60 dB
CD/TAPE/AUX
[Except Europe and U.K. models]
.................................................80 dB/75 dB
(DIN-Weighted, 40 kHz Dev.) Mono/Stereo
[Europe and U.K. models] ........74 dB/69 dB
Harmonic Distortion
<RX-485 RDS/385>
Mono/Stereo (1 kHz)
[Except Europe model]................0.1/0.2%
Mono/Stereo (40 kHz Dev.)
(Input 5.1 k-ohms Terminated 1 kHz)....60 dB
Tone Control Characteristics
BASS: Boost/cut .................±10 dB (50 Hz)
(Turnover frequency)
...........................................(350 Hz)
TREBLE: Boost/cut............±10 dB (20 kHz)
(Turnover frequency)
[Europe model]............................0.1/0.2%
<RX-385 RDS>
Mono/Stereo (1 kHz)
[Except Europe and U.K. models]
....................................................0.1/0.2%
Mono/Stereo (40 kHz Dev.)
..........................................(3.5 kHz)
Continuous Loudness Control
...............................................– 30 dB (1 kHz)
(Level related equalization)
[Europe and U.K. models] ...........0.1/0.2%
Stereo Separation
<RX-485 RDS/385> (1 kHz)................50 dB
Remote control transmitter
Batteries
Specifications are subject to change without
notice.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND
YAMAHA SCANDINAVIA A.B.
J
A
WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Download from Www.Somanuals.com. All Manuals Search And Download.
|