U
DVD AUDIO/VIDEO SA-CD PLAYER
LECTEUR DVD AUDIO/VIDEO SA-CD
DVD-S1800
HDMI
AUDIO DIRECT
STANDBY
ON
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION (for US customers)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications
not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/
s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your
FCC authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices.
Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful
to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur
in all installations. If this product is found to be the source of interference, which can be determined by turning the product
“OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., 6660 Orangethorpe Ave.
Buena Park, CA90622.
The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.
We Want You Listening For A Lifetime
Yamaha and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment
by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion - and,
most importantly, without affecting your sensitive hearing.
Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries
Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
For Customer Use:
Read carefully the information located at the rear panel of this
unit and enter below the Serial No. Retain this information for
future reference.
Model No.
Serial No. __________________________
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
CAUTION-VISIBLE AND INVISIBLE
DANGER
LASER RADIATION WHEN OPEN. DO NOT
STARE INTO BEAM OR VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS.
This unit emits visible laser radiation when open. Avoid direct
eye exposure to beam.
When this unit is plugged into a wall outlet, do not place your
eyes close to the opening of the disc tray and other openings or
look inside.
ii En
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
CAUTION: READ THIS BEFORE OPERATING THIS UNIT.
1
2
To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
Install this unit in a well ventilated, cool, dry, clean place
— away from direct sunlight, heat sources, vibration,
dust, moisture, or cold. In a cabinet, allow about 2.5 cm
(1 inch) of free space all around this unit for adequate
ventilation.
Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
Do not expose this unit to sudden temperature changes
from cold to hot, nor locate this unit in an environment
with high humidity (i.e., a room with a humidifier) to
prevent condensation inside this unit, which may cause an
electrical shock, fire, damage to this unit, and/or personal
injury.
common operating errors before concluding that this unit
is faulty.
16 Before moving this unit, press STANDBY/ON to set the
unit in standby mode, then disconnect the AC power plug
from the wall outlet.
17 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
18 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
3
4
The unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode. In
this state, this unit is designed to consume a very small
quantity of power.
5
Avoid installing this unit in a location where foreign
objects may fall onto this unit or where this unit may be
exposed to liquid dripping or splashing. On the top of this
unit, do not place:
FOR CANADIAN CUSTOMERS
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
This Class B digital apparatus complies with Canadian
ICES-003.
–
–
–
Other components, as they may cause damage and/
or discoloration on the surface of this unit.
Burning objects (i.e., candles), as they may cause
fire, damage to this unit, and/or personal injury.
Containers with liquid in them, as they may fall,
spilling the liquid and causing an electrical shock to
the user and/or damage to this unit.
WARNING
6
Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the
temperature inside this unit rises, it may cause fire,
damage to this unit, and/or personal injury.
Do not plug in this unit to a wall outlet until all
connections are complete.
Do not operate this unit upside-down. It may overheat,
possibly causing damage.
Do not use excessive force on switches, knobs and/or
cords.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE.
7
8
9
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a
qualified service person should remove the cover or attempt
to service this device.
10 When disconnecting the power cord from the wall outlet,
grasp the plug; do not pull the cord.
11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
LASER
Type
Wave length
Semiconductor laser GaAlAs
650 nm (DVD)
790 nm (VCD/CD)
1.45 mW (DVD)
1.13 mW (VCD/CD)
60 degrees
12 Use only the voltage specified on this unit. Using this unit
with a higher voltage than specified is dangerous and may
cause fire, damage to this unit, and/or personal injury.
Yamaha will not be held responsible for any damage
resulting from use of this unit with a voltage other than as
specified.
Output Power
Beam divergence
13 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reason.
14 When not planning to use this unit for long periods of
time (i.e., vacation), disconnect the AC power plug from
the wall outlet.
iii En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
INTRODUCTION
3
DISC OPERATION
18
Repeating a section
FUNCTIONAL OVERVIEW
5
(except DVD-Audio/MP3/WMA/JPEG) ...... 19
Random playback
Disc menu operation
Using the Video CD playback control (PBC)
menu (VCD/SVCD) ...................................... 21
On-screen display (OSD) menu
CONNECTIONS
10
Connecting an AV receiver with 6ch/
Using the OSD menu
multi-channel input ....................................... 10
(DVD/VCD/SVCD/CD) ............................... 21
Picture Setting menu
GETTING STARTED
15
Step 1: Inserting batteries into
®
(DVD-Video/VCD/SVCD/DivX /JPEG) .... 23
Setting the OSD (On-Screen Display)
Audio and Subtitle languages
Selecting a subtitle language
(DVD-Video) ................................................ 24
language ........................................................ 17
Setting the audio, subtitle and
®
DivX external subtitle files ....................... 24
disc menu languages ..................................... 17
®
MP3/WMA/Kodak picture CD) ................. 25
®
(DivX /MP3/WMA/Kodak picture CD) ...... 25
Bonus group playback
Changing the playback area
®
(MP3/WMA/DivX /JPEG) ......................... 26
Continued
1 En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
SETUP MENU
27
LANGUAGE CODE LIST
TROUBLESHOOTING
GLOSSARY
39
40
42
44
SPECIFICATIONS
®
registration code ............................................ 30
Selecting the black level
(U.S.A. and Canada models only) ................ 35
Selecting the closed caption
(U.S.A. and Canada models only) ................ 35
Switching the SCART video out
(U.K., Europe, and Russia models only) ...... 36
Selecting the default audio/subtitle/
DVD menu language .................................... 37
Selecting the PBC (playback control)
function ......................................................... 38
2 En
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
INTRODUCTION
Thank you for purchasing this unit. This Owner’s Manual
explains the basic operation of this unit.
Notes
•
CD-R(W), DVD-R(W) and DVD+R(W) cannot be played
unless finalized.
Copyright-protected WMA files cannot be played with this
unit.
This unit supports JPEG files of 2848 x 2136 pixels in size.
Some discs cannot be played depending on the recording
conditions, such as the PC environment and application
software. The characteristics and condition of some discs;
materials, scratches, curvature, etc., may result in playback
failure.
• Illustrations in this manual are based on the U.K.,
Europe, and Russia models unless otherwise specified.
• Notes contain important information about safety and
operating instructions.
•
•
•
• y indicates a tip for your operation.
• This manual is printed prior to production. Design and
specifications are subject to change in part as a result of
improvements, etc. In case of differences between the
manual and the product, the product has priority.
•
Be sure to use only CD-R(W), DVD-R(W) and DVD+R(W)
discs made by reliable manufacturers.
•
•
Do not use any non-standard shaped discs (heart-shaped, etc.).
Do not use discs with tape, seals, or paste on their surface.
Doing so may damage this unit.
Do not use discs affixed with labels printed by a commercially
available label printer.
Playable disc formats
• This unit is designed for use with the following discs:
DVD-Video, DVD-Audio, DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD+R DL, Video CD,
Super Video CD, Super Audio CD (SA-CD), Audio CD,
CD-R and CD-RW.
•
DVD region codes
This unit is designed to support the region management
system. Check the regional code number on the DVD disc
package. If the number does not match the region code of
this unit (see the table below or the back of this unit), this
unit may be unable to play the disc.
Region code
of this unit
Destination
Playable discs
U.S.A.
Canada
ALL
1
1
U.K.
Europe
ALL
2
3
5
2
• This unit can play:
– MP3, WMA (except copyright-protected WMA) and
picture (Kodak, JPEG) files recorded on CD-R(W)/
DVD-R(W)/DVD+R(W)
Asia
Korea
ALL
3
– JPEG/ISO 9660 format
– Maximum 14 character display
Russia
®
– DivX disc on CD-R(W)/DVD-R(W)/DVD+R(W)
ALL
5
®
– Official DivX Certified product
®
– Plays all versions of DivX video (including
®
®
DivX 6) with standard playback of DivX media
files
3 En
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Patent information
Cleaning discs
–
• When a disc becomes dirty, clean it with a cleaning
cloth. Wipe the disc from the center out. Do not wipe in
a circular motion.
• Do not use solvents such as benzine, thinner,
commercially available cleaners, or antistatic spray
intended for analog records.
Manufactured under license from Dolby Laboratories.
“Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered
trademarks of DTS, Inc.
Supplied accessories
Check your package to make sure it contains the following
items:
DivX, DivX Certified, and associated logos are
trademarks of DivX, Inc. and are used under license.
Remote
control
Batteries (x2)
(AAA, R03, UM-4)
“DCDi” is a trademark of Faroudja, a division of Genesis
Microchip, Inc.
POWER
DIMMER
HDMI AUDIO DIRECT STANDBY
GROUP
PAGE
MULTI 2CH
PROG
RANDOM
REPEAT
Audio pin cable
“HDMI”, the “HDMI” logo and “High Definition
Multimedia Interface” are trademarks or registered
trademark of HDMI Licensing LLC.
A
B
CLEAR
ENTER
SETUP
SLOW SEARCH
STOP
PLAY
PAUSE
This product incorporates copyright protection
technology that is protected by method claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other limited
viewing uses only unless otherwise authorized by
Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
SKIP
TOP MENU
ON SCREEN
Video pin cable
ENTER
MENU
RETURN
SUBTITLE AUDIO ANGLE ZOOM
Power cable
4 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL OVERVIEW
FUNCTIONAL OVERVIEW
Front panel
1
HDMI
AUDIO DIRECT
STANDBY
ON
2
3 4
5
6
7
8
9
0
1 Disc tray
6
Load a disc in the disc tray.
Opens or closes the disc tray.
2 STANDBY/ON
7 b/w
Searches backward.*
Moves to the previous chapter or track.
Turns on this unit or sets it to the standby mode.
3 HDMI indicator
Lights up green when an HDMI component is
recognized by this unit and the HDMI mode is set to
on.
8 f/a
Searches forward.*
Moves to the next chapter or track.
Lights up orange when no HDMI component is
recognized by this unit while the HDMI mode is set to
on.
9 p/e
Starts or pauses playback.
4 AUDIO DIRECT indicator
0 s
Lights up when you select the AUDIO DIRECT mode
by pressing AUDIO DIRECT on the remote control.
Stops playback.
5 Front panel display
* Press and hold the button for about two seconds.
Displays playback information or settings.
5 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL OVERVIEW
Front panel display
1
2
3
4
5
2
SVCD WMA P.SCAN TITLE GROUP CHP/TRK
MP3 JPEG
DVD AUDIO
DivX
D
MULTI D.MIX PROG. RANDOM ALL A
B
SA-CD
6
7
1 P.SCAN indicator
5 D.MIX indicator (DVD-Audio only)
Lights up when the progressive scan function is
Lights up when playing the disc that allows down
activated.
mixing of the multi-channel audio source.
2 Playback mode indicators
6 Disc indicators
Display the icon for the selected playback mode.
Display the icon for the disc type.
3 Decoder indicators
7 Information display
Display the icon for the selected internal decoder.
Displays various information such as a title/chapter/
track number or elapsed playing time.
4 MULTI indicator
Lights up when playing the multi-channel audio
source.
y
You can adjust the brightness of the front panel display using
DIMMER on the remote control.
6 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL OVERVIEW
Rear panel
1
2
3
4
5
6
7
MAINS
PR
PB
Y
/
/
CR
CB
VIDEO
CENTER
COAXIAL
IN
L
L
AV
R
R
MIXED 2CH FRONT SUBWOOFER SURROUND
OUT
ON
OFF
RS 232C
OPTICAL
DIGITAL
HDMI
S
VIDEO
COMPONENT
VIDEO OUT
AUDIO OUT
REMOTE CONTROL
8
9
0
q
w
(U.K., Europe, and Russia models)
1 AUDIO OUT (6ch discrete) jacks
7 MAINS
Connect to the 6ch input jacks of your AV receiver.
Connect the supplied power cable.
2 DIGITAL (COAXIAL) jack
8 AUDIO OUT (MIXED 2CH) jacks
Connect to the audio input jacks of your AV receiver or
stereo system.
Connect to the coaxial input jack of your AV receiver.
3 REMOTE CONTROL (IN/OUT) connectors
Use in custom installations to transmit remote control
signals via cable connections.
9 DIGITAL (OPTICAL) jack
Connect to the optical input jack of your AV receiver.
4 REMOTE CONTROL (RS-232C) terminal
(U.S.A., Canada, U.K., Europe, and Russia
models only)
0 HDMI jack
Connect to the HDMI input jack of your HDMI
component.
Use as an expansion terminal for commercial use.
Consult your dealer for details.
q VIDEO OUT (S VIDEO) jack
Connect to the S-video input jack of your AV receiver.
5 AV terminal
(U.K., Europe, and Russia models only)
Connect to SCART input terminal of your TV.
w VIDEO OUT (COMPONENT) jacks
Connect to the component input jacks of your AV
receiver.
6 VIDEO OUT (VIDEO) jack
Connect to the composite video input jack of your AV
receiver.
■ Remote control connectors and RS-232C terminal
The REMOTE CONTROL (IN/OUT) connectors and the REMOTE CONTROL (RS-232C) terminal are used in
custom installation. Keep the RS-232C switch set to OFF and do not connect any cables to these connectors during
normal use.
Caution: Do not touch the inner pins of the jacks on the rear panel of this unit. Electrostatic discharge
may cause permanent damage to this unit.
7 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL OVERVIEW
1 DIMMER
Selects from three different levels of brightness for the
Remote control
front panel display: bright, dim and auto.
For auto setting, brightness is automatically set to low
only during playback.
POWER
y
u
i
o
2 HDMI
DIMMER
HDMI AUDIO DIRECT STANDBY
Switches between the HDMI resolution settings or
turns off the HDMI mode (see page 36).
1
2
GROUP
PAGE
MULTI 2CH
3
4
y
PROG
RANDOM
REPEAT
•
You can select the HDMI resolution by pressing HDMI on
the remote control repeatedly or by using the HDMI Video
setup menu.
p
a
5
•
If you press HDMI on the remote control once, the
currently selected resolution setting is displayed in the top
left corner of the display and in the front panel display.
s
d
f
g
A
B
CLEAR
ENTER
6
7
SETUP
SLOW SEARCH
STOP
PLAY
PAUSE
3 GROUP
Selects the DVD-Audio group (see page 25).
h
8
9
SKIP
0
q
4 PAGE (+/–)
TOP MENU
ON SCREEN
j
k
ENTER
w
e
5 Numeric buttons (0-9)
Select numbered items in the currently displayed
menu.
MENU
RETURN
6 CLEAR
SUBTITLE AUDIO ANGLE ZOOM
Clear the mode or setting (see page 20).
l
;
r
t
7 SETUP
Accesses or exits from the setup menu of this unit
8 STOP (
7
)
Stops playback (see page 18).
9 PAUSE (
8
)
Pauses playback temporarily (see page 18).
Frame-by-frame playback (see page 18).
0 SKIP (l22 / 33l)
Moves to the previous/next chapter or track.
q TOP MENU
Displays the top-level disc menu.
y
The title menu is displayed for discs with the title menu.
8 En
Download from Www.Somanuals.com. All Manuals Search And Download.
FUNCTIONAL OVERVIEW
w Cursors (
/
/
/
)
d A-B
Selects an item in the currently displayed menu.
ENTER
Confirms the menu selection.
f ENTER
Confirms the menu selection.
e MENU
g SLOW/SEARCH (22 / 33)
Accesses the menu of a disc (see page 20).
Searches backward or forward (see page 19).
r SUBTITLE
h PLAY (
3
)
Selects the subtitle language (see page 24).
Starts playback (see page 18).
t AUDIO
j ON SCREEN
Accesses or exit from the on-screen display (OSD)
menu of this unit (see page 21).
Press twice during playback to access the Picture
Setting menu (see page 22).
y POWER (
l
)
u STANDBY (
)
k RETURN
Sets this unit to the standby mode (see page 15).
Returns to the previous setup menu.
i AUDIO DIRECT
l ZOOM
Turns off the video output during audio disc playback
in order to improve audio quality. Press again to turn on
the video output. This function is not available when an
HDMI component is recognized by this unit.
In the AUDIO DIRECT mode, the front panel display
goes out. Once this unit is turned off, the AUDIO
DIRECT mode is cleared (only when an SA-CD disc is
played back, the mode is cleared if the disc tray is
opened/closed).
Enlarges the video image (see page 23).
; ANGLE
Selects the DVD camera angle (see page 23).
y
Two ENTER buttons (w and f) act in the same way.
o MULTI/2CH
Selects a sound mode: Stereo or Multi-channel.
Changes the SA-CD playback area (see page 25).
p PROG
Accesses the program setup menu to program disc
tracks or exit from its menu (see page 20).
a RANDOM
s REPEAT
Repeats the chapter, track, title, group or disc
9 En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
CONNECTIONS
Connecting an AV receiver with 6ch/
multi-channel input
General notes on connections
Be sure to turn off this unit and unplug the power supply
cable, before you make or change connections.
• Depending on the component you want to connect, there
are various ways to make connections. Possible
connections are described below.
• Refer to the manuals supplied with your other
components as necessary to make the best connections.
• Do not connect this unit via your VCR. The video
quality could be distorted by the copy protection system.
• Do not connect the audio out jack of this unit to the
phono in jack of your audio system.
■ Analog connections
If you want to reproduce multi-channel Super Audio CD
(SA-CD) and DVD-Audio, connect AUDIO OUT (6ch
discrete) jacks of this unit to the corresponding input
jacks of your AV receiver using commercially available
audio pin cables.
CENTER
COAXIAL
IN
L
L
AV
Audio connections
R
R
MIXED 2CH FRONT
SUBWOOFER SURROUND
OUT
ON
OFF
RS 232C
OPTICAL
DIGITAL
HDMI
AUDIO OUT
REMOTE CONTROL
This unit (U.K., Europe,
and Russia models)
This unit has digital coaxial, digital optical, analog 6ch
discrete, and analog mixed 2ch output jacks. Connection
depends on the availability of audio jacks on your
component.
Connecting a stereo amplifier
Connect AUDIO OUT (MIXED 2CH) jacks of this unit to
the corresponding input jacks of your audio component
(such as a stereo amplifier) using the supplied audio pin
cable. You can connect a subwoofer to the
FRONT
CENTER SUBWOOFER
SURROUND
R
L
R
L
AV receiver
Speakers
SUBWOOFER jack.
This unit (U.K., Europe, and Russia models)
CENTER
COAXIAL
IN
L
L
AV
R
R
MIXED 2CH FRONT SUBWOOFER SURROUND
OUT
ON
OFF
RS 232C
OPTICAL
DIGITAL
HDMI
AUDIO OUT
REMOTE CONTROL
Audio pin cable
(supplied)
Stereo
amplifier
CD / DVD
R
L
Subwoofer
Left
speaker
Right
speaker
10 En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
■ Digital connections
Video connections
If you want to use the Dolby Digital, DTS, or MPEG
function on your AV receiver, connect DIGITAL
(OPTICAL) <A> or DIGITAL (COAXIAL) <B> jack of
this unit to the corresponding input jacks of your AV
receiver using a commercially available digital optical or
digital coaxial cable.
This unit has SCART, composite video, S-video, and
component video output jacks. If your AV receiver has
video output jacks, connect your receiver and then your
TV so that you can use one TV for several different video
sources (LD, VCR, etc.) by simply switching the input
source selector on your receiver.
Use the one that corresponds to the input jacks on the
component to be connected.
CENTER
COAXIAL
IN
L
L
AV
This unit (U.K., Europe, and Russia models)
R
R
MIXED 2CH FRONT SUBWOOFER SURROUND
OUT
ON
OFF
RS 232C
OPTICAL
DIGITAL
HDMI
AUDIO OUT
REMOTE CONTROL
PR
PB
Y
/
/
CR
CB
VIDEO
AV
This unit (U.K.,
Europe, and
Russia models)
RS 232C
ONTROL
S
VIDEO
COMPONENT
VIDEO OUT
HDMI
<A>
<B>
Video
pin cable
(supplied)
OPTICAL
IN
COAXIAL
IN
<A>
<B>
<C>
<D>
AV receiver
PB/CB PR/CR
Y
VIDEO
IN
S-VIDEO
IN
COMPONENT VIDEO IN
Speakers
AV
receiver
VIDEO
OUT
S VIDEO
OUT
COMPONENT
VIDEO OUT
VIDEO
IN
S VIDEO
IN
COMPONENT
VIDEO IN
Notes
•
If you make a connection with <A> or <B>, set [Digital Out]
If the audio format of the digital output does not match the
capabilities of your receiver, the receiver produces a distorted
sound or no sound at all. Make sure to select the appropriate
audio format from the menu screen on the disc.
TV
•
Pressing AUDIO on the remote control once or more may
change not only the audio languages but also the audio format.
SA-CD audio signals are not output from DIGITAL
(COAXIAL/OPTICAL) jacks.
If you want to enjoy Dolby Digital, DTS, and MPEG formats,
you must connect this unit to an AV receiver that supports
these formats.
•
•
11 En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
■ Composite video jack <A>
HDMI connection
HDMI (High-Definition Multimedia Interface) provides
high quality digital audio and video on a single
connection.
Connect the HDMI jack of this unit to an HDMI input jack
of your AV receiver, and then to that of your TV using a
commercially available HDMI cable.
If your receiver does not have an HDMI input jack, you
can achieve a better video image by connecting the HDMI
jack of this unit directly to the HDMI input jack of your
TV.
Connect VIDEO OUT (VIDEO) jack of this unit to the
video input jack of your AV receiver, and then to that of
your TV using the supplied video pin cable.
■ S-video jack <B>
S-video connections achieve a clearer picture than
composite video connections by transmitting video signals
on separate wires for luminance (Y) and chrominance (C).
Connect VIDEO OUT (S VIDEO) jack of this unit to
S-video input jack of your AV receiver, and then to that of
your TV using a commercially available S-video cable.
■ Component video jacks <C>
Component video connections achieve higher fidelity
color reproduction than S-video connections by
transmitting video signals on separate wires for luminance
(Y: green) and chrominance (PB: blue, PR: red). Connect
VIDEO OUT (COMPONENT) jacks of this unit to the
component input jacks of your AV receiver, and then to
those of your TV using a commercially available
component cable. Observe the color of each jack when
you make connections.
CENTER
COAXIAL
IN
L
L
AV
R
R
MIXED 2CH FRONT SUBWOOFER SURROUND
OUT
ON
OFF
RS 232C
OPTICAL
DIGITAL
HDMI
AUDIO OUT
REMOTE CONTROL
This unit (U.K., Europe, and
Russia models)
If your receiver does not have component output jacks,
you can achieve a better video image by connecting the
component output jacks of this unit directly to the
component input jacks of your TV.
HDMI
IN
■ SCART terminal <D>
AV receiver
(U.K., Europe, and Russia models only)
If your TV has only a terminal for video input, you can
connect the TV directly to this unit.
HDMI OUT
HDMI IN
Connect AV terminal of this unit to SCART input terminal
of your TV using a commercially available SCART cable.
Notes
TV
Speakers
•
Ensure that the “TV” indication on SCART cable is connected
to the TV set and “DVD” indication on SCART cable is
connected to this unit.
Notes
•
SCART video setting.
•
You need to make appropriate audio connections if the
connected component does not input audio signals (see
page 10).
•
•
This unit is not compatible with HDCP-incompatible HDMI or
DVI components.
You need a commercially available HDMI/DVI conversion
cable when you connect this unit to other DVI components. In
this case, you need to use another audio connection to this
connection because the HDMI jack of this unit does not output
any audio signals.
•
Do not disconnect or turn off the power of the HDMI/DVI
component connected to the HDMI jack of this unit while data
is being transferred. Doing so may disrupt playback or cause
noise.
y
When connecting an HDMI component, refer to the manual
supplied with your component.
12 En
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTIONS
■ HDMI video output
This unit is compatible with the following video formats:
480p/60 Hz, 576p/50 Hz, 720p/50 Hz, 60 Hz, 1080i/50 Hz, 60 Hz, and 1080p/50 Hz, 60 Hz.
Notes
•
You need to select one of the HDMI resolution settings by pressing HDMI on the remote control repeatedly or by using the HDMI
•
Depending on the connected DVI component, black and white in the image may not be distinct. In this case, adjust the picture setting
of the connected DVI component.
■ HDMI audio output
HDMI Audio
PCM
Analog output
setting
Audio format
Auto*1
Off
Off
–
Multi-channel
Stereo
PCM multi*2
PCM 2ch
Dolby Digital
Dolby Digital
Multi-channel
Stereo
PCM multi*2
DTS
DTS
DVD-Video
PCM 2ch
Multi-channel
Stereo
PCM multi*2
MPEG
MPEG
PCM 2ch
PCM 2ch*4
Multi-channel/Stereo
Multi-channel
Stereo
PCM 2ch
PCM 2ch
PCM (PPCM) multi*2,3
PCM (PPCM) 2ch*3
PCM (PPCM) 2ch
PCM (PPCM) multi*2,3
PCM (PPCM) 2ch*3
PCM (PPCM) 2ch
Multi
DVD-Audio
2ch*4
Multi-channel/Stereo
CD/MP3/
2ch
Multi-channel/Stereo
PCM 2ch
PCM 2ch
WMA/DivX®
Multi-channel
Stereo
PCM multi*2
PCM 2ch
PCM 2ch
PCM 2ch
PCM multi*2
PCM 2ch
PCM 2ch
–
Multi
DTS-CD
DTS
PCM 2ch
MPEG
–
2ch
Multi-channel/Stereo
Multi-channel/Stereo
Multi-channel
VCD
SVCD
SA-CD
2ch
Multi
Stereo
2ch
Multi-channel/Stereo
Multi-channel/Stereo
Multi/2ch
*1:If the connected HDMI component does not support bitstream signals (Dolby Digital, DTS, and MPEG), the audio
output is automatically changed from bitstream signals to PCM signals.
*2:If the HDMI component does not support multi-channel audio signals, the audio output is automatically changed
from PCM multi-channel signals to PCM stereo signals and 48 kHz/16 bits signals or less.
*3:If the audio source is prohibited from downmixing, the front L/R channel audio and 48 kHz/16-bit signals or less are
output instead of downmixed stereo.
*4:If the connected component does not support more than 48 kHz, the audio output is automatically changed to 48 kHz/
16-bit signals or less.
Notes
•
•
SA-CD signals cannot be output using HDMI. Make an analog connection to listen to SA-CD (see page 10).
13 En
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
GETTING STARTED
y
If the settings you have made are inappropriate, you can always reset all options and your personal settings to the initial factory settings.
For details, see “Resetting the system” on page 30.
Using the remote control
Use the remote control within 6 m (20 ft approx.) of this
Step 1: Inserting batteries into
the remote control
unit and point it toward the remote control sensor.
3
2
1
within 6m
(20 ft approx.)
1 Press the
part and slide the battery
compartment cover off.
2 Insert the two supplied batteries (AAA, R03,
UM-4), following the indications (+/–) on the
inside of the compartment.
3 Slide the cover back until it snaps into place.
Notes
•
•
•
Do not spill water or other liquids on the remote control.
Do not drop the remote control.
Do not leave or store the remote control in the following types
of conditions:
– places of high humidity, such as near a bath
– places of high temperature, such as near a heater or stove
– places of extremely low temperature
– dusty places
Notes
•
•
•
•
Insert batteries correctly according to the polarity markings
(+/–). The batteries inserted in the opposite direction may leak.
Replace the exhausted batteries immediately with new ones to
prevent a leakage.
Remove the batteries from the compartment if the remote
control is not used for more than a month.
If the batteries have leaked, dispose of them immediately.
Avoid touching the leaked material or letting it come into
contact with clothing, etc. Clean the battery compartment
thoroughly before installing new batteries.
Step 2: Turning on the power
1 Make sure that the power cable is connected to
•
•
Do not use old batteries together with new ones.
Do not use different types of batteries (such as alkaline and
manganese batteries) together. Read the packaging carefully as
these different types of batteries may have the same shape and
color.
an AC outlet.
2 Turn on your TV and AV receiver.
3 Select the appropriate input source of the AV
receiver connected to this unit. Refer to the
manual supplied with your AV receiver for
details.
•
Dispose of the batteries correctly in accordance with your local
regulations.
4 Press STANDBY/ON on the front panel or
POWER ( ) on the remote control to turn on
l
this unit.
➜ The front panel display lights up.
5 Set the TV to the correct Video IN channel (e.g.,
EXT1/2, AV1/2, AUDIO/VIDEO, etc. Refer to
the manual supplied with your TV for details).
➜ The default screen appears on the TV.
15 En
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
3 Press
/
repeatedly to highlight [TV
Step 3: Setting a TV type
Type].
This unit is compatible with both NTSC and PAL video
formats. Select the color system that matches your TV.
VIDEO
1/1
TV Display
TV Type
16:9
y
NTSC
•
Press RETURN to display the previous menu.
Wide Screen Format
Black Level*1
Off
Off
•
Press SETUP to exit from the setup menu.
1 Press SETUP.
Closed Caption*1
Still Mode
Off
Field
Interlaced
RGB
➜ The setup menu appears.
Component
SETUP
1/2
Scart Video Out*2
GENERAL
AUDIO
DVD-Audio mode
SA-CD mode
Move :
Return Select : Enter
OSD Language
Parental Rating
Parental Password
Screen Saver
4 Press
/
to select one of the options below.
SPEAKER
VIDEO
PAL
Select this if the connected TV is a PAL system TV. It will
change video signals of NTSC discs and output them in
PAL format.
HDMI
Auto Power Off
Sleep Timer
DISC
Move :
Return
Select : Enter
NTSC
Select this if the connected TV is an NTSC system TV. It
will change video signals of PAL discs and output them in
NTSC format.
2 Press
/
repeatedly to select [VIDEO],
and then press ENTER.
➜ [VIDEO] menu appears.
MULTI
Select this if the connected TV is compatible with both
NTSC and PAL formats (such as a multi-system TV). The
output format will be in accordance with the video signals
of the disc.
VIDEO
1/1
TV Display
16:9
NTSC
Off
TV Type
Wide Screen Format
Black Level*1
Closed Caption*1
Still Mode
Off
Notes
Off
•
Before changing the current TV Standard setting, ensure that
your TV supports the selected TV type system.
If you play an NTSC-formatted disc with the [PAL] setting or a
PAL-formatted disc with the [NTSC] setting, the video quality
may deteriorate.
Field
Interlaced
RGB
Component
•
Scart Video Out*2
Move :
Return
Select : Enter
•
When [TV Type] is set to [MULTI], this unit may change the
HDMI resolution unwantedly. In this case, try the [NTSC] or
[PAL] setting.
*1: [Black Level] and [Closed Caption] are only for U.S.A. and
Canada models.
*2: [Scart Video Out] is only for U.K., Europe, and Russia
models.
16 En
Download from Www.Somanuals.com. All Manuals Search And Download.
GETTING STARTED
Setting the audio, subtitle and disc
menu languages
Step 4: Setting a language
preference
You can select your own preferred language settings. This
unit will automatically switch to your preferred language
for you whenever you load a disc. If the language selected
is not available on the disc, the default language of the disc
will be used instead. The OSD (On-Screen Display)
language in the system menu will remain once selected.
1 Press SETUP.
➜ The setup menu appears.
2 Press
/
repeatedly to highlight [DISC],
and then press ENTER.
➜ [DISC] menu appears.
DISC
1/1
y
•
•
Press RETURN to display the previous menu.
Press SETUP to exit from the setup menu.
AUDIO Language
Subtitle Language
DVD Menu Language
Angle Mark
English
Off
English
On
Setting the OSD (On-Screen Display)
language
PBC
Off
Time Interval
3 sec
1 Press SETUP.
➜ The setup menu appears.
Move :
2 Press
/
repeatedly to highlight
Return Select : Enter
[GENERAL], and then press ENTER.
➜ [GENERAL] menu appears.
3 Press
/
repeatedly to highlight [AUDIO
Language] or [Subtitle Language] or [DVD
Menu Language].
GENERAL
1/2
DVD-Audio mode
SA-CD mode
DVD-Audio
SA-CD
English
Level 8
- - - -
4 Press
/
to select a language.
OSD Language
Parental Rating
Parental Password
Screen Saver
■ To select the language not in the list:
1 Select [Others] under [AUDIO Language] or
On
[Subtitle Language] or [DVD Menu Language].
Auto Power Off
Sleep Timer
Mode 1
Off
2 Press ENTER.
3 Use the numeric buttons (0-9) to enter the
4-digit language code (see “LANGUAGE CODE
Move :
Return
Select : Enter
3 Press
/
repeatedly to highlight [OSD
to select a language.
4 Press ENTER.
Language].
4 Press
/
17 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
DISC OPERATION
3 Press
again to close the disc tray.
➜ After recognizing the disc, this unit starts to play
Notes
•
Unless otherwise specified, all operations described here are
carried out using the supplied remote control.
back automatically.
•
•
If you press PLAY ( 3) when the disc tray is
opened, the disc tray closes and playback starts
automatically.
Depending on the disc, the disc reading time may
exceed 30 seconds due to the complexity of the
directory/file configuration.
•
If the inhibition icon ( or “Prohibit”) appears on the TV
screen when you press a button, the function for that button is
not available on the current disc or at the current time.
Depending on the DVD or Video CD disc, some operations
may operate differently or be restricted.
Do not push on the disc tray or put any objects other than discs
on the disc tray. Doing so may cause the disc unit to
malfunction.
•
•
4 To stop playback, press STOP (
7
).
➜ “RESUME” appears in the front panel display.
5 To resume playback, press PLAY ( 3).
Basic operation
➜ The disc is played back from the last stopping
point.
GROUP
PAGE
MULTI 2CH
y
As long as you do not eject a disc, you can resume playback even
if you turn off this unit.
PROG
RANDOM
REPEAT
Numeric
buttons (0-9)
6 To cancel resume mode, press STOP (
7
)
twice.
A
B
CLEAR
ENTER
Notes
SETUP
SLOW SEARCH
SLOW/SEARCH
•
It may not be possible to play certain MP3/JPEG/DivX® discs
(
/
)
STOP
PLAY
PAUSE
due to the configuration and characteristics of the disc or the
recording conditions.
STOP (
)
)
PLAY (
)
PAUSE (
•
When you play a down mix prohibited disc, “NO DOWN
MIX” lights in the front panel display.
SKIP
SKIP (
/
)
TOP MENU
ON SCREEN
Pausing playback
1 During playback, press PAUSE (
8
).
1 Press
on the front panel to open the disc tray.
➜ Playback is paused and the sound is muted.
2 Place a disc in the disc tray with the printed side
2 Press PAUSE (
8
) again to select the next
up.
picture frame (frame-by-frame playback).
3 To resume normal playback, press PLAY ( 3).
Selecting a track/chapter
Press SKIP (l22 / 33l) or use the numeric
buttons (0-9) and ENTER to select a track/
chapter number.
•
You can move to the top of the currently playing
track/chapter by pressing SKIP (l22 ) once, and
move to the previous track/chapter by pressing
SKIP (l22 ) twice.
During repeat playback of a track/chapter, press
SKIP (l22 / 33l) to replay the same track/
chapter.
•
18 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
®
MP3, WMA, JPEG, DivX
Searching backward/forward
Folder
All
Track
1 Press SLOW/SEARCH (22 / 33).
•
For slow search, press PAUSE (
pause playback before pressing
SLOW/SEARCH (22 / 33).
8
) to
OFF
Chapter: repeats the current chapter
Title: repeats the current title
Track: repeats the current track
Group: repeats the current group
Folder: repeats the current folder
All*: repeats the entire disc
2 While searching, press
SLOW/SEARCH (22 / 33) repeatedly
to select the desired speed.
3 To resume normal playback, press PLAY ( 3).
OFF: exits from repeat mode
Notes
*: This feature may not be available with some discs.
•
For WMA, DTS-CD and JPEG, the search function (backward,
forward and slow playback) is not available.
For MP3, slow playback is not available.
For VCD, SVCD and DivX®, the slow backward function is
not available.
Note
•
•
For VCD and SVCD, repeat playback is not available when the
PBC mode is selected.
Repeating a section
(except DVD-Audio/MP3/WMA/JPEG)
Repeat playback
You can repeat single chapter/track, single title/group or
entire disc. Also, you can set two points (start and end
points) to repeat the specified section.
1 During playback, press A-B at the desired
starting point.
2 Press A-B again at the desired end point.
➜ The selected section repeats continuously.
REPEAT
REPEAT
A
B
3 To exit from the sequence, press A-B.
CLEAR
ENTER
SLOW SEARCH
A-B
SETUP
Random playback
(except DVD/SA-CD)
You can play tracks in random order.
Repeating playback
Press REPEAT to select the repeat play mode.
➜ Each time you press the button, the display on the
PROG
TV screen changes as follows:
RANDOM
RANDOM
REPEAT
DVD-Video
Title
Group
All
Chapter
OFF
1 During playback, press RANDOM.
➜ “RANDOM” appears in the front panel display
DVD-Audio
and all tracks are played in random order.
Track
2 To resume normal playback, press RANDOM
again.
OFF
CD, SA-CD, VCD, SVCD
Track
OFF
19 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
Program playback (CD)
You can customize the playback order for tracks stored in
the disc. This unit supports a maximum of 20 programmed
tracks.
Note
Once you take out the disc from the disc tray or turn off this unit,
the stored program play content is cleared.
GROUP
PAGE
MULTI 2CH
Disc menu operation
(DVD/VCD/SVCD)
Many DVD, Video CD (version 2.0 only), and SVCD
discs include original navigational menus called “DVD
menus” and “Video CD playback control menus”. These
menus provide a convenient way to operate the disc.
PROG
RANDOM
REPEAT
PROG
Numeric
buttons (0-9)
A
B
CLEAR
ENTER
CLEAR
SETUP
SLOW SEARCH
GROUP
PAGE
MULTI 2CH
STOP
PLAY
PAUSE
STOP (
)
PROG
RANDOM
REPEAT
Numeric
buttons (0-9)
SKIP
TOP MENU
ON SCREEN
A
B
CLEAR
ENTER
/
/
/
ENTER
ENTER
SKIP (
SETUP
SLOW SEARCH
ENTER
MENU
RETURN
STOP
PLAY
PAUSE
RETURN
SKIP
/
)
1 Press STOP (
2 Press PROG.
7
) to stop playback if necessary.
TOP MENU
ON SCREEN
/
/
/
ENTER
➜ The program setup menu appears on the TV
ENTER
MENU
RETURN
screen.
MENU
RETURN
3 Use the numeric buttons (0-9) to enter a track
number you want to store as a program play.
4 Press
5 Repeat step 3-4 until you store all desired tracks.
to select [Play Program]
to move the cursor to the next field.
Using the DVD menu
1 Press MENU.
6 Use
/
/
/
➜ The DVD menu appears on the TV screen.
and then, press ENTER to start program
playback.
•
Depending on the disc, the DVD menu may appear
once you load the disc.
■ To clear the selected track number
Press CLEAR.
2 Use
/
/
/
or the numeric buttons
(0-9) to select a playback feature or item.
3 Press ENTER to start playback.
■ To clear the list
■ To exit from the menu
Press MENU.
Use
/
/
/
to select [Clear All], and
then press ENTER.
20 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
Using the Video CD playback control
(PBC) menu (VCD/SVCD)
Using the OSD menu
(DVD/VCD/SVCD/CD)
1 Press MENU to turn on the PBC function.
➜ The disc menu appears on the TV screen.
During playback, press ON SCREEN.
➜ A list of available disc information appears on the
TV screen.
•
Depending on the disc, the disc menu may appear
once you load the disc.
DVD-Video
2 Use SKIP (l22 / 33l) or the numeric buttons
(0-9) to select a playback option.
1
2
3
4
5
DVD VIDEO
Title 1 / 1
00 : 00 : 10
02 : 15 : 30
3 During playback, press RETURN to return to
Chapter 1 / 7
MPEG 5.1 Ch
Time 00 : 00 : 10
the menu screen.
Audio 1 / 1
Subtitle 1 / 1
Angle 1 / 1
■ To skip the index menu and play back a
Bitrate
3.072 Mbps
disc directly from the beginning
Press MENU to turn off the PBC function.
0
9
8
7
6
DVD-Audio
y
You can also use the setup menu to turn on or off the playback
control (PBC) function (see “Selecting the PBC (playback
1
2
3
4
5
DVD AUDIO
Group 1 / 1
Audio 1 / 1
00 : 00 : 10
02 : 15 : 30
Track 1 / 8
Time 00 : 00 : 10
96 k / 24 bit
On-screen display (OSD) menu
(DVD/VCD/SVCD/SA-CD)
MLP 5.1 Ch
Angle 1 / 1
Subtitle 1 / 1
Page 1 / 1
The OSD menu shows disc playback information (e.g., the
title or chapter number, elapsed playing time or audio/
subtitle language). A number of operations are possible
without interrupting disc playback.
0
8
7
6
q
VCD/SVCD/CD
2
w
GROUP
PAGE
MULTI 2CH
VCD
PROG
RANDOM
REPEAT
Track 1 / 7
00 : 00 : 10
Numeric
buttons (0-9)
Time
Track Elapsed
A
B
CLEAR
ENTER
e
SETUP
SLOW SEARCH
STOP
PLAY
PAUSE
1: Current title or group number/Total number of titles or groups
2: Current chapter or track number/Total number of chapters or tracks
3: Elapsed time
SKIP
4: Time remaining
TOP MENU
ON SCREEN
ON SCREEN
5: Elapsed time (You can input numbers for time search.)
6: Audio information
ENTER
/
/
/
7: Current angle number/Total number of available angles
8: Current subtitle number/Total number of available subtitle languages
9: Data transmission speeds
MENU
RETURN
0: Current audio number/Total number of available audio languages
q: Current page number/Total number of pages
w: Time (You can select a category of time.)
e: Category of time being displayed on w
21 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
■ To select a title (DVD-Video)/group
■ To select a category of time
(DVD-Audio)
(VCD/SVCD/CD)
1 Press
/
/
/
repeatedly to highlight
Press
/
/
/
repeatedly to highlight
1, and then enter a title/group number using the
numeric buttons (0-9).
w, and then press ENTER to toggle between the
category of time.
2 Press ENTER.
■ To exit from the OSD menu
Press ON SCREEN.
■ To select a chapter (DVD-Video)/track
(VCD/SVCD/DVD-Audio)
Displaying text information (SA-CD)
1 Press
/
/
/
repeatedly to highlight
2, and then enter a chapter or track number
using the numeric buttons (0-9).
Some SA-CD discs contain text information (e.g., track
name, album name, artist name etc.). If SA-CD text is
available on the disc, the track name is automatically
displayed on the TV screen once you load the disc.
2 Press ENTER.
■ To search for a time
■ To display the album/artist name
During playback, press ON SCREEN.
1 Press
/
/
/
repeatedly to highlight
5, and then enter hours, minutes and seconds
from left to right using the numeric buttons
(0-9).
Picture Setting menu
(DVD/VCD/SVCD)
2 Press ENTER.
Note
This unit comes with 10 sets of picture color settings that
you can define yourself.
When searching for a time, if you enter a time outside the total
time for the group/track currently being played back, the
inhibition icon ( ) is displayed.
Adjusting picture settings
■ To select an angle/subtitle/audio
1 Press ON SCREEN twice during playback.
➜ The Picture Setting menu appears on the TV
1 Press
/
/
/
repeatedly to highlight
screen.
7, 8 or 0, and then enter a audio, subtitle or
angle number using the numeric buttons
(0-9).
2 Press
/
to highlight the desired
to adjust the selected
parameter and
/
parameter.
2 Press ENTER.
Picture Setting
01/09
Note
You cannot change the [Angle]/[Subtitle]/[Audio] setting if the
function is not available on the disc you are playing.
Brightness
Move :
0
Adjust :
■ To select a page (DVD-Audio)
3 Press ON SCREEN to exit from the setup
menu.
1 Press
/
/
/
repeatedly to highlight
q, and then enter a page number using the
numeric buttons (0-9).
➜ You can adjust the following parameters.
Brightness
2 Press ENTER.
Set this to adjust the overall brightness of the image.
Contrast
Set this to adjust the bright areas (white level) in the
image.
Hue
Set this to adjust the hue or phase of the image.
22 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
Sharpness Mid
Set this to adjust the sharpness of the image for the
intermediate frequencies.
Zooming pictures
(DVD-Video/VCD/SVCD/DivX®/
JPEG)
Sharpness High
Set this to adjust the sharpness of the image for the high
frequencies.
You can enlarge the picture on the TV screen and to pan
through the enlarged picture.
DNR
TOP MENU
ON SCREEN
Set this to reduce video noise.
Gamma
ENTER
/
/
/
Set this to adjust the intensity of the picture non-linearly.
MENU
RETURN
Chroma level
Set this to adjust the density of the color.
Chroma delay
Set this to adjust the advance delay of the chroma signal
for a perfectly clear picture.
SUBTITLE AUDIO ANGLE ZOOM
ZOOM
True Life
Set this to adjust the intensity of the picture details. A
positive value enables you to reproduce the minute signals
of video sources. This function is only available for
progressive scan (using the component video jacks) and
HDMI output.
1 During playback, press ZOOM repeatedly to
display the picture at different scales (ZOOM
150%, 200%, 300%, or 400%).
2 Press
/
/
/
to pan through the
Availability of picture settings varies according to the
connection and settings.
enlarged picture.
3 Press ZOOM repeatedly to return to the original
Progressive
Interlaced
size.
HDMI
(Component) (Component)
Viewing angles (DVD-Video)
If the disc contains sequences recorded from different
camera angles, you can view the picture from a number of
different angles.
Brightness
Contrast
Hue
0 to +6
–6 to +6
–6 to +6
0 to +6
–6 to +6
–6 to +6
0 to +6
–6 to +6
–6 to +6
(S-video and
CVBS only)
Sharpness
Mid
Not
available
–6 to +6
–6 to +6
–6 to +6
SUBTITLE AUDIO ANGLE ZOOM
ANGLE
Sharpness
High
Not
available
–6 to +6
DNR
0 to +6
0 to +6
0 to +6
Gamma
Not
available
–6 to +6
–6 to +6
Note
Viewing angles available for each disc may vary. Refer to the
operating instructions in the DVD menu or on its jacket.
Chroma
level
–6 to +6
–6 to +6
–2 to +2
0 to +6
–6 to +6
–2 to +2
Press ANGLE repeatedly to select the desired
angle.
Chroma
Delay
Not
available
True Life
0 to +6
Not available
Note
All picture settings are not available for CVBS (composite video)
and S-video ouput.
23 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
Audio and Subtitle languages
(DVD-Video/VCD)
If the disc contains multi-language options, you can select
audio/subtitle languages.
DivX® external subtitle files
®
The font sets listed below are available for DivX external
®
subtitle files. To watch DivX discs with the desired font
set, set the default subtitle language setting in the setup
menu to the desired language (see “Setting the audio,
Note
This unit supports the following languages:
Albanian, Breton, Bulgarian, Byelorussian, Catalan,
Croatian, Czech, Danish, Dutch, English, Faroese,
Finnish, French, German, Hungarian, Icelandic, Irish,
Italian, Kurdish (Latin), Macedonian, Greek, Hebrew,
Moldavian, Norwegian, Polish, Portuguese, Romanian,
Russian, Serbian, Slovak, Slovenian, Spanish, Swedish,
Turkish, Ukrainian
Languages available for each disc may vary. Refer to the
operating instructions in the disc menu or on its jacket.
y
You can set default audio/subtitle languages in the setup menu
page 17).
SUBTITLE AUDIO ANGLE ZOOM
Notes
SUBTITLE
•
•
•
Some discs cannot be played depending on disc characteristics
or recording conditions.
Some external subtitle files may be displayed incorrectly or not
at all.
For external subtitle files, the following filename extensions of
subtitle format are supported (note that these files are not
shown within the disc navigation menu):
AUDIO
Selecting an audio language
.srt, .sub, .ssa, .smi, .ass, .txt, .psb, .sami
The filename of the movie file has to be same as the filename
for the external subtitle file.
•
•
Press AUDIO repeatedly to select an audio
language.
For a movie file, only one external subtitle file can be loaded.
Note
Changing pages (DVD-Audio)
For VCD, this function is only available when the [Analog
Output] setting is set to [Stereo] (see “Setting the analog output”
Many DVD-Audio discs include slide show and page turn
capabilities. You can display information pages for photo
galleries, artist biographies, lyrics, etc. if the function is
available for the disc.
Selecting a subtitle language
(DVD-Video)
Press PAGE (+/–) repeatedly to move to the
next/previous page.
Press SUBTITLE repeatedly to select a subtitle
language.
DIMMER
HDMI AUDIO DIRECT STANDBY
GROUP
PAGE
MULTI 2CH
PROG
PAGE (+/ )
24 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
Group/File selection (DVD-Audio/
DivX /MP3/WMA/Kodak picture
Bonus group playback
(DVD-Audio)
®
CD)
Some DVD-Audio discs contain bonus groups that require
a four-digit password to gain access. In this case, refer to
the disc jacket and other packaging for information.
You can select a track in a specific group for DVD-Audio
discs and a track/file in a folder for data disc.
GROUP
PAGE
MULTI 2CH
GROUP
PAGE
MULTI 2CH
GROUP
GROUP
PROG
RANDOM
REPEAT
PROG
RANDOM
REPEAT
Numeric
buttons (0-9)
Numeric
buttons (0-9)
A
B
A
B
CLEAR
ENTER
CLEAR
ENTER
ENTER
SETUP
SLOW SEARCH
ENTER
SETUP
SLOW SEARCH
STOP
PLAY
PAUSE
STOP
PLAY
PAUSE
SKIP
SKIP
TOP MENU
ON SCREEN
TOP MENU
ON SCREEN
ON SCREEN
/
ENTER
/
ENTER
ENTER
ENTER
MENU
RETURN
MENU
RETURN
1 Press GROUP.
➜ A group icon appears on the TV screen.
Selecting a group (DVD-Audio)
DVD AUDIO
1 Press GROUP.
➜ A group icon appears on the TV screen.
Group
Move :
01 / 08
DVD AUDIO
Select : Enter
Group
Move :
01 / 08
2 Use
/
or the numeric buttons (0-9)
Select : Enter
to select a bonus group number, and then press
ENTER.
2 Use
/
or the numeric buttons (0-9)
3 Enter a four-digit password using the numeric
buttons (0-9), and then press ENTER.
to select a group number.
3 Press ENTER.
4 Press
ENTER.
/
to select a track, and then press
Selecting a file in a folder
®
(DivX /MP3/WMA/Kodak picture CD)
Changing the playback area and
layer (SA-CD)
1 Press
/
to select a folder, and then press
ENTER to open the folder.
There are three types of SA-CD discs: single-layer, dual-
layer and hybrid. Each type may contain up to two areas of
recorded information: a High Quality Stereo area and a
High Quality Multi-channel area. You can switch between
the SA-CD multi-channel and SA-CD stereo areas.
2 Press to select a file, and then press
ENTER.
➜ Playback starts from the selected file.
/
•
If you use the numeric buttons (0-9) to select a
file, playback starts from the selected file
automatically.
y
You can also change the analog output setting using the setup
25 En
Download from Www.Somanuals.com. All Manuals Search And Download.
DISC OPERATION
GROUP
PAGE
MULTI 2CH
Media Player
Time
00 : 00 : 10
0
MULTI /2CH
PROG
RANDOM
REPEAT
ROOT
SCRNE
JPEG
. .
JPG A_0510
1
2
3
4
5
JPG
B_0618
JPG B_0630
C_0731
A
B
JPG
JPG C_0729
CLEAR
ENTER
SETUP
SLOW SEARCH
STOP
PLAY
PAUSE
STOP (
)
Move :
Select : Enter
2 Press
/
to select a folder, and then press
1 Press STOP (
7
) to stop playback.
ENTER to open the folder.
•
To move to the upper folder, select the folder icon
with two dots when disc playback is stopped.
2 Press MULTI/2CH.
➜ MULTI indicator lights up when the multi-channel
area is selected.
3 Press
ENTER.
➜ Playback starts from the selected file.
/
to select a file, and then press
Multimedia file playback
(MP3/WMA/DivX®/JPEG)
You can play MP3, WMA, DivX and JPEG files on a
personally recorded CD-R/RW disc or commercial CD.
•
If you use the numeric buttons (0-9) to select a
file, playback starts from the selected file
automatically.
®
Notes
Displaying the thumbnail screen (JPEG)
•
Some files cannot be played correctly depending on disc
characteristics or recording conditions.
This unit supports JPEG files of 2848 x 2136 pixels in size.
However, some files may not be displayed correctly depending
on the aspect ratio of the image.
1 Press MENU during playback.
➜ The thumbnail pictures appear on the TV screen.
•
y
PROG
RANDOM
Numeric
buttons (0-9)
REPEAT
A
B
CLEAR
ENTER
SLOW SEARCH
2 Press SKIP (l22 / 33l) to display the other
SETUP
pictures on the previous/next page.
STOP
PLAY
PAUSE
3 Press
/
/
/
to highlight one of the
STOP (
)
pictures, and then press ENTER to start
SKIP
playback.
SKIP (
/
/
)
TOP MENU
ON SCREEN
4 Press STOP (
7
) to return to the data disc
menu.
/
/
ENTER
ENTER
MENU
RETURN
MENU
Rotating pictures (JPEG)
During playback, press
/
/
/
to
rotate the picture on the TV screen.
1 Load a disc in the disc tray.
➜ Playback starts automatically.
: rotates the picture counter-clockwise by 90
degrees
➜ For MP3 and WMA, the data disc menu appears
on the TV screen.
: rotates the picture clockwise by 90 degrees
®
➜ For DivX and JPEG, press STOP (
7
) during
,
: rotates the picture by 180 degrees
playback to display the data disc menu.
26 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
SETUP MENU
Menu overview
y
•
The initial setting for each parameter is indicated in bold.
•
If the settings you have made are inappropriate, you can always reset all options and your personal settings to the initial factory
settings. For details, see “Resetting the system” on page 30.
Main Menu
Menu item
DVD-Audio mode
SA-CD mode
Setting Item/Submenu
DVD-Audio, DVD-Video
Setting item/Parameter
GENERAL
SA-CD, CD
OSD Language
Parental Rating
Parental Password
Screen Saver
Auto Power Off
Sleep Timer
English, Français, Español,
_ _ _ _ (Enter your password)
_ _ _ _ (Enter your password)
On, Off
Level 1 to Level 8
New Password, Confirm Password
Mode 1, Mode 2, Off
Off, 30min, 60min, 90min,120min,150min
_ _ _ _ (Enter your password)
(DivX registration code is displayed)
Stereo, Multi-Channel
All, PCM, Off
Factory Default
DivX Registration
Analog Output
Digital Out
Yes, No
Enter
AUDIO
LPCM Output
Night Listening Mode
Size
48KHz, 96KHz
On, Off
SPEAKER
Front L/R
Large, Small
Large, Small, Off
On, Off
Center, Surround L/R
Subwoofer
Initialize
On, Off
Distance
Level
Unit
Feet, Meter
Front L/R, Center, Surround L/R
1ft to 40ft (0.3m to 12.0m)
Default setting: 10ft (3.0m)
Initialize
On, Off
Front L, Center, Front R, Surround L, Surround R,
Subwoofer
0dB to –12dB
Test Tone
Off, Manual, Auto
On, Off
Initialize
SA-CD
SA-CD Config
Config 1, Config 2, Config 3
60, 80, 100, 120
CUT-OFF Frequency
16:9, 4:3 Pan Scan, 4:3 Letter Box
MULTI, NTSC, PAL
NL Stretch, Pillar Box, Off
On, Off
VIDEO
TV Display
TV Type
Wide Screen Format
Black Level (U.S.A. and
Canada models only)
Closed Caption (U.S.A.
On, Off
and Canada models only)
Still Mode
Frame, Field
Component
Progressive, Interlaced
CVBS, RGB
Scart Video Out (U.K.,
Europe, and Russia
models only)
HDMI
DISC
HDMI Video
480p/576p, 720p, 1080i, 1080p, Auto
Standard, Enhanced
DVI Output Range
HDMI Audio
Auto, PCM, Off
AUDIO Language
Subtitle Language
DVD Menu Language
Angle Mark
Off ([Subtitle Language] only), English, French,
Spanish, Japanese, German, Italian, Russian,
Others
On, Off
PBC
On, Off
Time Interval
2 sec to 10 sec, Default setting: 3 sec
27 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
2 Press
/
to select the desired main menu,
Setup menu operation
and then press ENTER.
➜ Menu items and setting items appear.
Setup is carried out on the TV screen, enabling you to
customize this unit to suit your own particular
requirements. Follow the procedures below to start the
setup menu operations.
SPEAKER
1/1
Size
Distance
Level
REPEAT
SA-CD
A
B
CLEAR
ENTER
SLOW SEARCH
SETUP
SETUP
STOP
PLAY
PAUSE
Move :
Return
Select : Enter
SKIP
TOP MENU
ON SCREEN
3 Press
/
to highlight the desired menu item.
➜ If the selected menu item has submenus, only a
right arrow is displayed on the side of the setting
item. In this case, press , and then repeat step 3.
/
/
/
ENTER
ENTER
MENU
RETURN
RETURN
SPEAKER
1/1
SA-CD Config
Config 1
100
CUT-OFF Frequency
SUBTITLE AUDIO ANGLE ZOOM
y
Move :
Return
Select : Enter
•
•
•
Press RETURN to display the previous menu.
Press SETUP to exit from the setup menu.
Refer to the following pages for details of the menu that
requires a particular operation.
➜ If the selected menu item has only setting items,
left and right arrows appear on both sides of the
setting item.
1 Press SETUP.
AUDIO
1/1
➜ Main menus and menu items appear on your TV.
Analog Output
Digital Out
Stereo
PCM
SETUP
GENERAL
AUDIO
1/2
LPCM Output
96KHz
Off
DVD-Audio mode
SA-CD mode
Night Listening Mode
OSD Language
Parental Rating
Parental Password
Screen Saver
SPEAKER
VIDEO
HDMI
Auto Power Off
Sleep Timer
Move :
Return
Select : Enter
DISC
Move :
Return
Select : Enter
4 Press
/
to toggle the setting items or to
adjust the parameter.
28 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
General setup menu
Notes
•
•
•
This setting is only available when no disc is loaded in the disc
tray.
Selected mode becomes effective after you close the setup
menu.
When you select [CD], this unit does not play back SA-CD
discs which do not have CD layer.
SETUP
1/2
GENERAL
AUDIO
DVD-Audio mode
SA-CD mode
OSD Language
Parental Rating
Parental Password
Screen Saver
SPEAKER
VIDEO
Setting the OSD language
This menu contains various options for the on-screen
display (OSD) language. For details, see “Setting the OSD
HDMI
Auto Power Off
Sleep Timer
DISC
Move :
Return Select : Enter
Restricting playback with parental
control
Some DVD discs have a parental level assigned to the
complete disc or to certain scenes on the disc. This feature
lets you set a playback limitation level.
The rating levels are from 1 to 8 and are country
dependent. You can prohibit playback of certain discs that
are not suitable for your children or play certain discs in
alternative scenes.
Selecting DVD-Audio mode
Some DVD-Audio discs contain the DVD-Video content
in addition to the DVD-Audio content. You can select
DVD-Audio or DVD-Video mode.
•
Select [DVD-Audio mode] in [GENERAL] menu.
DVD-Audio
Select this to play back both DVD-Audio and DVD-Video
contents. Only the DVD-Audio content may be played
back depending on the disc.
1 Select [Parental Rating] in [GENERAL] menu.
2 Enter your four-digit password using the
numeric buttons (0-9). (For details about the
password, see “Changing the parental password”
below.)
DVD-Video
Select this to play back only the DVD-Video content.
Notes
➜ If the password is correct, [Parental Rating] is
enabled to select.
•
This setting is only available when no disc is loaded in the disc
tray.
3 Press
/
to select the rating level.
•
Selected mode becomes effective after you close the setup
menu.
•
To disable parental controls and have all discs play,
select [Level 8].
y
•
When a DVD-Audio disc is played back, the DVD AUDIO
indicator lights up.
Notes
•
When you select [DVD-Video], the DVD AUDIO indicator
goes out.
•
VCD, SVCD, CD and SA-CD have no level indication, so the
parental control function has no effect with these types of
discs.
•
Some DVD discs are not encoded with a rating though the
movie rating may be printed on the disc cover. The rating level
feature does not work for such discs.
Selecting SA-CD mode
Some SA-CD discs contain both SA-CD layer and the
standard CD layer. You can select SA-CD or CD mode.
Changing the parental password
•
Select [SA-CD mode] in [GENERAL] menu.
You can change the password for parental control. Enter
your four-digit password when prompted on the screen.
The default password is “2580”.
SA-CD
Select this to play back SA-CD layer.
CD
1 Select [Parental Password] in [GENERAL]
Select this to play back CD layer.
menu.
29 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
2 Enter your old four-digit password using the
numeric buttons (0-9).
Resetting the system
You can reset all options and your personal settings to the
initial factory settings, except [Parental Rating] and
[Parental Password].
•
When doing this for the first time, enter “2580”.
➜ If the password is correct, the submenu appears.
3 Enter the new four-digit password using the
numeric buttons (0-9).
1 Select [Factory Default] in [GENERAL] menu.
➜ [Confirm Password] is highlighted.
2 Enter your four-digit password using the
numeric buttons (0-9). (For details about the
4 Enter the new four-digit password again.
➜ The previous menu screen appears and the new
four-digit password is now valid.
➜ The confirmation screen appears.
Setting the screen saver
You can turn on or off the screen saver.
GENERAL
2/2
. . . .
Factory Default
DivX Regis
•
Select [Screen Saver] in [GENERAL] menu.
Factory Default
On
Select this to turn on the screen saver when disc playback
is stopped for more than 15 minutes.
Press [Yes] to confirm
Yes
No
Off
Select this to disable the screen saver function.
Move :
Return Select : Enter
Setting the auto power function
3 Press
/
to select [Yes] to reset the system,
You can set the auto standby mode.
and then press ENTER.
•
Select [Auto Power Off] in [GENERAL] menu.
➜ All settings are reset to the initial factory settings.
Mode 1
Select this to set this unit to the standby mode
automatically when disc playback is stopped for more
than 30 minutes or disc playback is continued for more
than six hours without operation.
®
Displaying the DivX VOD registration
code
®
Yamaha provides you with the DivX VOD (Video On
Demand) registration code that allows you to rent and
purchase videos using the DivX VOD service.
Mode 2
®
Select this to set this unit to the standby mode
automatically when disc playback is stopped for more
than 30 minutes.
1
Select [DivX Registration] in [GENERAL] menu.
Off
2 Press
.
Select this to disable the auto power off function.
➜ The registration code appears.
3 Press ENTER to return to the previous menu.
Setting the sleep timer
You can set this unit to the standby mode automatically
after a certain elapsed period.
y
To purchase or rent the videos from DivX® VOD service at
video onto a CD-R for playback on this unit.
•
Select [Sleep Timer] in [GENERAL] menu.
30min, 60min, 90min, 120min, 150min
Notes
Select one to set the sleep timer function.
•
All videos downloaded from DivX® VOD can only be played
back on this unit.
The time search function is not available during DivX® movie
Off
•
Select this to cancel the sleep timer function.
playback.
30 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Setting the LPCM output
Audio setup menu
Set the LPCM output if you have connected this unit to a
PCM-compatible receiver via a digital terminal, such as
the coaxial or optical terminals.
SETUP
1/1
Discs are recorded at a certain sampling rate. The higher
the sampling rate, the better the sound quality.
GENERAL
AUDIO
Analog Output
Digital Out
LPCM Output
•
Select [LPCM Output] in [AUDIO] menu.
SPEAKER
VIDEO
Night Listening Mode
48KHz
Select this to play back discs recorded at the sampling rate
of 48 kHz. All 96 kHz PCM data streams (if available) are
converted to the sampling rate of 48 kHz.
HDMI
DISC
96KHz
Move :
Select : Enter
Return
Select this to play back discs recorded at the sampling rate
of 96 kHz. If the 96 kHz disc is copy protected, the digital
output is automatically converted to a sampling rate of 48
kHz.
Setting the analog output
Set the analog output to match the playback capability of
this unit.
Setting the night listening mode
•
Select [Analog Output] in [AUDIO] menu.
In this mode, high volume output is softened and low
volume output is brought upward to an audible level. It is
useful when you watch your favorite action movie without
disturbing others at night.
Stereo
Select this to change channel output to stereo, which only
delivers sound from the two front speakers.
Multi-Channel
•
Select [Night Listening Mode] in [AUDIO]
menu.
Select this when using a multi-channel audio/(video)
receiver with 6 channel inputs. In this mode, this unit
performs DTS decoding or Dolby Digital 5.1-channel
decoding when applicable.
On
Select this to level out the volume. This feature is only
available for movies with Dolby Digital mode.
Off
Setting the digital output
Select this when you want to enjoy the full dynamic range
of surround sound.
Set the digital output according to your optional audio
component connections.
Note
•
Select [Digital Out] in [AUDIO] menu.
This mode is only effective for analog output.
All
Select this if you have connected the digital audio output
jack to a multi-channel decoder/receiver.
PCM
Select this only if your receiver is not capable of decoding
multi-channel audio signals.
Off
Select this to turn off the digital output.
31 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Initialize
Speaker setup menu
You can reset [Size] settings to the initial factory settings.
1 Select [Initialize] under [Size] in [SPEAKER]
SETUP
1/1
menu.
GENERAL
Size
2 Press
.
Distance
➜ The confirmation screen appears.
AUDIO
Level
3 Select [Yes] to reset the setting, and then press
SPEAKER
VIDEO
SA-CD
ENTER.
➜ [Size] settings are reset to the initial factory
HDMI
settings.
DISC
Move :
Select : Enter
Return
Setting speaker distances
You can set the distances for individual speakers.
Placing all speakers except for the subwoofer at equal
distances from the listener is the most ideal way of the
speaker positioning in 5.1 channel system.
Setting speaker sizes
You can set the sizes for individual speakers.
•
Select [Distance] in [SPEAKER] menu.
•
Select [Size] in [SPEAKER] menu.
Unit
Front L/R
You can select the display unit of measurement.
Set the sizes for front L/R speakers.
Feet
Large
Select this to input speaker distances in feet.
Select this if the connected speakers are large.
Meter
Small
Select this to input speaker distances in meters.
Select this if the connected speakers are small.
Front L/R
Center, Surround L/R
Set the distance from your listening position to the front
speakers. We recommend to place the front left speaker
and right speaker at the same distance from the listening
position.
Set the sizes for center/surround L/R speakers.
Large
Select this if the connected speakers are large.
Small
Center
Select this if the connected speakers are small.
Set the distance from your listening position to the center
speaker.
Off
Select this if no center/surround L/R speakers are
connected.
Surround L/R
Subwoofer
Select on or off for the subwoofer.
Set the distance from your listening position to the
surround speakers. We recommend to place the surround
left speaker and right speaker at the same distance from
the listening position.
On
Select this if a subwoofer is connected.
Control range: 1ft to 40ft (0.3m to 12.0m)
Control step: 1ft (0.3m)
Off
Select this if no subwoofer is connected.
Notes
Notes
•
These settings are not available for SA-CD discs. See “Setting
the SA-CD configuration” on page 33 for the SA-CD setting.
[Center], [Surround L/R] and [Subwoofer] settings are not
available when the [Analog Output] setting is set to [Stereo]
•
For the [Center] setting, you cannot specify the distance
beyond the [Front L/R] setting or below the [Front L/R] setting
minus 5ft (1.5m).
For the [Surround L/R] setting, you cannot specify the distance
beyond the [Front L/R] setting or below the [Front L/R] setting
minus 15ft (4.5m).
•
•
32 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Initialize
Initialize
You can reset [Distance] settings to the initial factory
settings.
You can reset [Level] settings to the initial factory settings.
1 Select [Initialize] under [Level] in [SPEAKER]
1 Select [Initialize] under [Distance] in
menu.
[SPEAKER] menu.
2 Press
.
2 Press
.
➜ The confirmation screen appears.
➜ The confirmation screen appears.
3 Select [Yes] to reset the setting, and then press
3 Select [Yes] to reset the setting, and then press
ENTER.
ENTER.
➜ [Level] settings are reset to the initial factory
➜ [Distance] settings are reset to the initial factory
settings.
settings.
Setting the SA-CD configuration
Setting speaker levels
You can set the volume levels for individual speakers.
You can select speaker sizes and on/off statuses for
SA-CD discs. You can also select a cut-off (cross-over)
frequency for all low-frequency signals. All frequencies
below the selected frequency are sent to the subwoofer.
•
Select [Level] in [SPEAKER] menu.
Front L, Center, Front R, Surround L, Surround R,
Subwoofer
•
Select [SA-CD] in [SPEAKER] menu.
SA-CD Config
Select speaker sizes and on/off statuses from the following
three settings.
Set the volume levels for front L/R speakers, center
speaker, surround L/R speakers or subwoofer.
Control range: 0dB to –12dB
Control step: 1dB
Size or on/off
Speaker
Test Tone
Config 1
Large
Large
Large
On
Config 2
Small
Small
Small
On
Config 3
Large
Small
Small
Off
A test tone can be output to help you judge the volume
level of each speaker.
Front L/R
Center
1 Select [Test Tone] under [Level] in [SPEAKER]
menu.
Surround L/R
Subwoofer
2 Press
Off
/
to select [Off], [Manual] or [Auto].
Select this to output no test tone.
CUT-OFF Frequency
Manual
Select a cut-off (cross-over) frequency for all low-
frequency signals. All frequencies below the selected
frequency are sent to the subwoofer.
Select this to output the test tone manually.
Auto
Select this to output the test tone from each speaker
automatically.
Control range: 60, 80, 100, 120 (Hz)
3 For [Auto], press
press ENTER to output the test tone. For
[Manual], press to select each speaker,
and then press ENTER to output the test tone.
/
to select [Yes], and then
/
Notes
•
The test tone is not output from a center speaker, surround
speakers, and a subwoofer when the [Analog Output] setting is
set to [Stereo] (see “Setting the analog output” on page 31).
These settings are only effective for analog output.
•
33 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
When the aspect ratio of your TV is 4:3:
Video setup menu
Playback
TV display
Setting
disc
SETUP
1/1
*2
16:9
GENERAL
AUDIO
TV Display
4:3 Pan
Scan
TV Type
Wide Screen Format
Black Level*1
Closed Caption*1
Still Mode
SPEAKER
VIDEO
4:3
16:9
4:3
HDMI
Component
Scart Video Out*2
DISC
4:3 Letter
Box
Move :
Return
Select : Enter
*1: [Black Level] and [Closed Caption] are only for U.S.A. and
Canada models.
*2: [Scart Video Out] is only for U.K., Europa, and Russia
models.
*1: The side of the picture may be stretched depending on the
TV. In this case, check the screen size and aspect ratio of
your TV.
*2: If the disc is not assigned to play back with panscan, it is
played with letterbox.
Setting the TV display
Set the aspect ratio of this unit to match your TV. The
format you select must be available on the disc.
•
Select [TV Display] in [VIDEO] menu.
Setting the TV type
This menu contains the options for selecting the color
4:3 Pan Scan
Select this if the aspect ratio of your TV is 4:3. In this
setting, both sides of the picture to be trimmed or
formatted to fit your TV screen.
Selecting the wide screen format
Set the aspect ratio of the projected images on the screen.
This function is only available for progressive scan and
HDMI output.
4:3 Letter Box
Select this if the aspect ratio of your TV is 4:3. In this
setting, a wide picture with black bands on the upper and
lower portions of the TV screen are displayed.
16:9
•
Select [Wide Screen Format] in [VIDEO] menu.
Select this if you have a widescreen TV.
NL Stretch
■ The relationship between the setting of this
unit and the TV display
Select this to display of 4:3 image on the 16:9 screen with
non-linear stretching. (The center position of the screen is
stretched less than the side.)
When the aspect ratio of your TV is 16:9 (widescreen):
Pillar Box
Playback
disc
TV display
Setting
Select this to display 4:3 image on the 16:9 screen without
stretching. Even when this unit is playing a disc recorded
in the 16:9 squeeze mode, the picture is displayed in the
center of the screen.
16:9
16:9
Off
*1
4:3
Select this to make no aspect ratio adjustment.
34 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Selecting the black level
Setting the still mode
(U.S.A. and Canada models only)
If you set the [TV Type] to [NTSC] (see “Step 3: Setting a
TV type” on page 16), set this setting shift to [On] to
improve the color contrast during playback.
You can select the picture quality for pausing or frame-by-
frame playback.
•
Select [Still Mode] in [VIDEO] menu.
Frame
•
Select [Black Level] in [VIDEO] menu.
Select this if the picture is unstable when you select
[Field].
On
Select this to enhance the black level.
Field
Select this for the standard still mode setting. This setting
is suitable for playback of quick motion scenes.
Off
Select this for the standard black level setting.
Notes
Selecting the scan function
•
This function is only available for CVBS (composite video)
and S-video output.
This function is only available if you have connected this
unit to a progressive scan TV through the component
video jacks (see “Component video jacks <C>” on
page 12). This function is enable you to enjoy accurate
color reproduction and high quality images. This unit
features DCDi circuit.
•
This setting has no effect if the [TV Type] is set to [PAL] or
Selecting the closed caption
(U.S.A. and Canada models only)
•
Select [Component] in [VIDEO] menu.
Closed captions are data hidden in the video signals of
specific discs, and are invisible without the use of a special
decoder. The difference between subtitles and captions is
that subtitles are intended for hearing persons and captions
are for the hearing impaired. Subtitles rarely show all of
the audio. For example, captions show sound effects (e.g.,
“phone ringing” and “footsteps”), while subtitles do not.
Before you select this setting, please ensure that the disc
contains closed caption information and your TV set also
supports this function.
Progressive
Select this to enable the progressive scan function. The
confirmation screen appears if you select this. In this case,
select [Yes] and then press ENTER.
Interlaced
Select this to enable the interlaced scan function.
y
The P.SCAN indicator on the front panel display lights up during
progressive playback.
•
Select [Closed Caption] in [VIDEO] menu.
Notes on activating progressive scan:
• While HDMI video signals are being output, component
video is fixed to interlaced video.
On
Select this to enable the closed caption function.
• In progressive mode, 4:3 aspect images are stretched
horizontally on the widescreen TV. Change the aspect
ratio settings of your TV if you want to watch the
original aspect ratio images without distortion. You can
also change the aspect ratio settings in [Wide Screen
Format] menu (see “Selecting the wide screen format”
Off
Select this to disable the closed caption function.
Note
This function is only available for CVBS (composite video) and
S-video output.
• Ensure that your TV is equipped with progressive scan.
• Connect using a component video cable.
35 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
HDMI setup menu
CONSUMERS SHOULD NOTE THAT NOT ALL HIGH
DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE
ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN
CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE
PROBLEMS, IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE “STANDARD
DEFINITION” OUTPUT. IF THERE ARE QUESTIONS
REGARDING OUR VIDEO MONITOR COMPATIBILITY
WITH THIS MODEL 525P AND 625P DVD PLAYER,
PLEASE CONTACT OUR CUSTOMER SERVICE
CENTER.
SETUP
1/1
GENERAL
AUDIO
HDMI Video
DVI Output Range
HDMI Audio
SPEAKER
VIDEO
HDMI
DISC
This unit is compatible with the complete line of Yamaha
products, including the projectors DPX-1300, DPX-830 and
the plasma monitor PDM-4220.
Move :
Select : Enter
Return
Switching the SCART video out
(U.K., Europe, and Russia models
only)
Select this setting to toggle the video signal output from
the AV terminal between CVBS (composite video) and
RGB.
Setting the HDMI video
You can adjust the resolution depending on the monitor
you are using. This function is only available when this
unit is connected to an HDMI-compatible component via
the HDMI jack.
This unit is compatible with the following video formats:
480p/60 Hz, 576p/50 Hz, 720p/50 Hz, 60 Hz, 1080i/50
Hz, 60 Hz, and 1080p/50 Hz, 60 Hz.
•
Select [Scart Video Out] in [VIDEO] menu.
CVBS
•
Select [HDMI Video] in [HDMI] menu.
Select this to output composite video signals.
480p/576p
Select this for 480/576 progressive-scan video.
RGB
Select this to output RGB video signals.
720p
Note
Select this for 720 progressive-scan video.
This unit does not output S-video signal from the AV terminal.
1080i
Select this for 1080 interlaced-scan video.
1080p
Select this for 1080 progressive-scan video.
Auto
Select this to set this unit to the best resolution setting
automatically based on your monitor.
Notes
•
•
•
When [TV Type] is set to [NTSC] or [PAL], video signals with
480p or 576p are output accordingly.
While HDMI video signals are being output, component video
is fixed to interlaced video.
For settings other than [Auto], make sure that the selected
resolution is supported by the HDMI-compatible monitor you
are using.
If the selected resolution is not supported, this setting is
automatically switched to the most appropriate resolution, and
the newly selected resolution is displayed in the top left corner
of the display and in the front panel display temporarily.
When you select [1080p] and use an HDMI cable longer than
5 m (16 ft), the picture quality may decrease.
•
36 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
y
•
Refer to the manual supplied with your monitor to select the
appropriate aspect ratio.
DISC setup menu
•
You can also select the HDMI resolution by pressing HDMI on
the remote control repeatedly.
SETUP
1/1
GENERAL
AUDIO
AUDIO Language
Subtitle Language
DVD Menu Language
Angle Mark
Selecting the DVI output range
You can select the DVI output range to match the
connected component. This function is only available
when this unit is connected to an DVI-D-compatible
component via the HDMI jack.
SPEAKER
VIDEO
PBC
Time Interval
HDMI
•
Select [DVI Output Range] in [HDMI] menu.
DISC
Standard
Move :
Return
Select : Enter
Select this if you cannot see the correct image when you
select [Enhanced].
Enhanced
Selecting the default audio/subtitle/
DVD menu language
Select this if black and white in the image is not distinct.
These menus contain various language options for the
audio, subtitles and disc menus recorded on the DVD. For
Setting the HDMI audio
Set the HDMI audio output to match the connected
component. This function is only available when this unit
is connected to an HDMI-compatible component via the
HDMI jack.
For details about the relationship between the audio
format and the setting, see “HDMI audio output” on
Selecting an angle mark display
You can switch an angle mark display on or off when
sequences recorded from different camera angles are
played back.
•
Select [HDMI Audio] in [HDMI] menu.
•
Select [Angle Mark] in [DISC] menu.
Auto
On
Select this to set this unit to the best setting automatically
based on the component you have connected via the
HDMI jack.
Select this if you want to display an angle mark. An angle
mark is displayed continuously.
Off
PCM
Select this if you do not want to display an angle mark. An
angle mark appears for five seconds, and then disappears.
Select this to output the decoded multi-channel or 2ch
linear PCM audio signals via the HDMI jack.
Off
Select this to turn off the HDMI audio output.
Notes
•
•
SA-CD signals cannot be output using HDMI.
When [HDMI Audio] is set to [Auto] or [PCM], digital output
signals are muted.
37 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENU
Selecting the PBC (playback control)
function
You can set playback control (PBC) to on or off. This
function is available only on Video CD 2.0 with the
playback control (PBC) feature.
•
Select [PBC] in [DISC] menu.
On
Select this to display a disc menu.
Off
Select this not to display a disc menu.
y
You can also use the MENU button on the remote control to turn
on or off the playback control (PBC) function (see “Using the
page 21).
Setting the duration for a slide show
You can set the duration that the slides for JPEG files are
displayed.
•
Select [Time Interval] in [DISC] menu.
2 sec to 10 sec
Control step: 1 second
Note
This setting may not work correctly depending on file sizes.
38 En
Download from Www.Somanuals.com. All Manuals Search And Download.
LANGUAGE CODE LIST
LANGUAGE CODE LIST
Abkhazian
Afar
1112 Fiji
1620 Lingala
1619 Lithuanian
1628 Macedonian
1635 Malagasy
1722 Malay
2224 Singhalese
2919
2921
2922
2925
1529
2931
2933
2932
3022
3017
3011
3030
3015
3018
1225
3019
3025
3028
3021
3033
3121
3128
3136
3219
3225
1335
3325
3418
2019
3525
3631
1111 Finnish
1116 French
2927 Frisian
1123 Galician
1128 Georgian
1835 German
1129 Greek
2230 Slovak
2321 Slovenian
2317 Somali
2329 Spanish
2322 Sundanese
2330 Swahili
2319 Swedish
2328 Tagalog
2325 Tajik
Afrikaans
Albanian
Amharic
Arabic
2111 Malayalam
1415 Maltese
1522 Maori
Armenian
Assamese
Aymara
1135 Greenlandic
1136 Guarani
1211 Gujarati
1531 Hausa
2122 Marathi
1724 Moldavian
1731 Mongolian
1811 Nauru
Azerbaijani
Bashkir
2324 Tamil
Basque
2411 Tatar
Bengali; Bangla
Bhutani
1224 Hebrew
1436 Hindi
1933 Nepali
2415 Telugu
2425 Thai
1819 Norwegian
1831 Oriya
Bihari
1218 Hungarian
1228 Icelandic
1217 Indonesian
2335 Interlingua
1215 Irish
2528 Tibetan
2611 Tigrinya
2629 Tonga
1611 Turkish
2622 Turkmen
2630 Twi
Breton
1929 Panjabi
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
1924 Pashto, Pushto
1911 Persian
1711 Polish
2123 Italian
1930 Portuguese
2011 Quechua
2033 Raeto-Romance
2124 Romanian
2129 Russian
2121 Samoan
2135 Sanskrit
2125 Scots Gaelic
2131 Serbian
6765 Japanese
3618 Javanese
1325 Kannada
1828 Kashmiri
1329 Kazakh
1411 Kirghiz
2422 Korean
1524 Kurdish
1525 Laothian
1530 Latin
2731 Ukrainian
2823 Urdu
Chinese
Corsican
Croatian
Czech
2825 Uzbek
2831 Vietnamese
2923 Volapük
2911 Welsh
1714 Wolof
2928 Xhosa
2918 Yiddish
2924 Yoruba
2914 Zulu
Danish
Dutch
English
Esperanto
Estonian
Faroese
2225 Serbo-Croatian
2211 Shona
1625 Latvian, Lettish
2232 Sindhi
39 En
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TROUBLESHOOTING
Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below
or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized
Yamaha dealer or service center.
See
page
Problem
Solution
No power
No picture
Connect the AC power cable properly.
Press STANDBY/ON on the front panel of this unit to turn on the
power.
Refer to the manual supplied with your TV for correct Video In
channel selection. Change the TV channel until you see the DVD
screen.
–
Turn on your TV.
–
Make sure that all connections on this unit and on all other
components are secure.
If [Component] is set to [Progressive], check that you have connected
this unit to a progressive scan TV through the component video jacks.
Otherwise, follow the steps below to turn off the progressive scan;
1. Press
on the front panel to open the disc tray.
2. Press CLEAR on the remote control.
3. Press “2580” using the numeric buttons (0-9) on the remote
control.
4. Press AUDIO on the remote control.
If [HDMI Video] is set to other than [Auto], check that the resolution
is supported by the HDMI-compatible monitor you have connected.
Otherwise, follow the steps below to change the setting to [Auto];
1. Press s twice on the front panel or STOP (
7
) twice on the
remote control to stop playback.
2. Press and hold s and p/e on the front panel at the same time for
three seconds.
If the HDMI indicator flashes orange, check that you have connected
this unit to an HDCP-compatible component.
Check that the video signal output setting matches the video
connection.
Completely distorted picture or
black/white picture
Check that the disc is compatible with this unit.
Check that the TV type of this unit is set to match that of the disc and
your TV. If you set the TV type improperly, follow the steps below to
restore the TV Type setting to the default setting;
1. Press
on the front panel to open the disc tray.
2. Press CLEAR on the remote control.
3. Press “2580” using the numeric buttons (0-9) on the remote
control.
4. Press AUDIO on the remote control.
Check the video connection.
The screen size looks unnatural, Check that the TV setting of this unit matches the screen aspect ratio
or the caption is displayed only
partially on the TV monitor or is
not displayed at all
of your TV.
Change the screen size and the aspect ratio of your TV.
–
40 En
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
See
page
Problem
Solution
No sound or distorted sound
Adjust the volume on the TV or the AV receiver.
Check that the speakers are connected properly.
Adjust the volume level in the setup menu.
Check the digital connections.
–
–
No audio at digital output
If you are playing a DTS source, check that your receiver can decode
DTS and [Digital Out] is set to [All].
If you are playing an MPEG-2 source, check that your receiver can
decode MPEG-2. Otherwise, make sure that [Digital Out] is set to
[PCM].
Check that the audio format of the selected audio option on the disc
matches your receiver capabilities.
–
No audio at HDMI output
Make sure that [HDMI Audio] is set to [Auto] or [PCM].
No audio signals via the HDMI jack are output if the DVI-D
component is connected to this unit using the HDMI-DVI converter
cable.
To output audio signals via the HDMI jack, connect an HDMI
component to this unit.
Disc does not play
Check that the disc format is supported.
–
The CD-R/RW, DVD+R/RW and DVD-R/RW must be finalized.
Check that the disc label is facing up.
–
Check that the disc is defective by trying another disc.
If you have recorded a JPEG, MP3 or WMA disc yourself, check that
your disc contains at least ten JPEG picture files or five MP3/WMA
music tracks.
–
Check the region code of the DVD disc.
Picture freezes momentarily
during playback
Check the disc for fingerprints/scratches and clean it with a soft cloth
wiping from the center to the edge.
This unit does not respond to
the remote control
Aim the remote control directly at the remote control sensor on the
front panel.
Reduce the distance of the remote control from this unit.
Replace the batteries in the remote control.
–
Reinsert the batteries with their polarities (+/– signs) as indicated.
Buttons do not work
Disconnect the power cable from the AC outlet for a few minutes.
Reconnect the power cable and try to operate again as usual.
This unit does not respond to
some operating commands
during playback
Operations may not be permitted by the disc. Refer to the instructions
of the disc jacket.
–
Menu items cannot be selected
Depending on the connection status or disc availability, some menu
items cannot be selected.
–
–
Cannot play back SA-CD disc
When [SA-CD mode] is set to [CD], this unit does not play back
SA-CD discs which does not have CD layer.
®
No sound during DivX movies
The audio code may not be supported by this unit.
playback
41 En
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
GLOSSARY
■ Aspect ratio
■ Dolby Digital
Horizontal and vertical ratio of a displayed image. The
horizontal vs. vertical ratio of conventional TV is 4:3, and
that of wide-screens is 16:9.
Digital surround sound system which is developed by
Dolby Laboratories provides completely independent
multi-channel audio. With 3 front channels (left, center,
and right) and 2 surround stereo channels, Dolby Digital
provides five full-range audio channels. With an additional
channel especially for bass effects (called LFE, or low
frequency effect), the system has a total of 5.1-channels
(LFE is counted as 0.1 channel). By using 2-channel
stereo for the surround speakers, more accurate moving
sound effects and surround sound environment are
possible than with Dolby Surround.
■ Bit
Short for binary digit. Represents the smallest unit of
information manipulated on a computer. In audio systems,
the bit size determines resolution to digitize analog
signals.
The larger the bit size, the larger the dynamic range (the
ratio of maximum and minimum frequency level) and the
finer the sounds. Generally, an audio CD is 16 bit and
DVD audio is 24 bit.
■ DTS
Digital surround sound system developed by DTS, Inc.,
which provides 5.1 channel audio (max). With an
abundance of audio data, it is able to provide authentic-
sounding effects.
■ Bit rate
The amount of data used to hold a given length of music;
measured in kilobits per second, or kbps. Also, the speed
at which you record. Generally, the higher the bit rate, or
recording speed, the better the sound quality. However,
higher bit rates use more space on a disc.
■ DVD-Audio
It has developed for the sole purpose of creating high
quality pure sound with Linear PCM and Packed PCM
(lossless coding) in up to six audio-channels. Sampling
frequencies of 192 kHz/24 bits are supported.
■ Component video jacks
Jacks for inputting or outputting a component video
signal. Component video signal consists of three lines, the
luminance signal (Y) and two color difference signals (PB/
CB, PR/CR), which enable to provide high-quality video.
■ HDMI
HDMI (High-Definition Multimedia Interface) is the first
industry-supported, uncompressed, all-digital A/V (audio/
video) interface. Providing an interface between any A/V
source (such as a set-top box or A/V receiver) and an
audio/video monitor (such as a digital television – DTV),
HDMI supports standard, enhanced or high-definition
video as well as multi-channel digital audio using a single
cable.
■ DivX®
®
DivX is a popular media technology created by DivX,
®
inc. DivX media files contain highly compressed video
with high visual quality that maintains a relatively small
file size. DivX files can also include advanced media
features like menus, subtitles, and alternate audio tracks.
®
HDMI transmits all ATSC (Advanced Television Systems
Committee) HDTV standards and supports 8-channel
digital audio, with bandwidth to spare to accommodate
future enhancements and requirements.
®
Many DivX media files are available for download
online, and you can create your own using your personal
content and easy-to-use tools from DivX.com.
42 En
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
■ Interlace
■ Region code
The most common type of scanning used in televisions. It
divides a screen into even and odd numbered fields for
scanning, and then builds an image by combining them
into one image (frame).
Many DVD discs include a region code so that the
copyright owner can control DVD software distribution
only to regions where they are ready to distribute. There
are six regions codes, which restrict a DVD player to
playing a DVD disc with the same region code.
■ JPEG (Joint Photographic Expert Group)
A standardized image compression system proposed by
the Joint Photographic Expert Group. It can reduce image
data sizes to 1 to 10% of their original sizes, and works on
digital photographs effectively.
■ S-video jack
A jack for inputting or outputting an S-video signal.
S-video signal consists of two lines, the luminance signal
(Y) and color signal (C), which enable to provide high-
quality video during playback or recording.
■ MP3 (MPEG Audio Layer-3)
■ Super Audio CD
An audio file compression technology. It can reduce audio
data sizes to about 10% of their original sizes while
maintaining CD-level audio quality.
Audio format based upon the current CD standards but
includes a greater amount of information that provides
higher quality sound. There are three types of discs: single
layer, dual layer and hybrid discs. The hybrid disc can be
played on existing CD players as well as Super Audio CD
players since it contains both standard audio CD and
Super Audio CD information.
■ MPEG (Moving Pictures Experts Group)
International standard for digital video and audio
compression generated by ISO (International Organization
for Standardization) and IEC (International
Electrotechnical Commission).
Includes MPEG-1, MPEG-2, and MPEG-3. MPEG-1
offers VHS level video quality and is often used on video
CDs. MPEG-2 offers S-VHS level video quality and is
often used on DVDs.
Super Audio CD Disc
Hybrid layer disc
Dual layer disc
Single layer disc
HD layer
HD layer
CD layer
HD layer
■ Parental control
Limits Disc play according to the age of the users or the
limitation level in each country. The limitation varies from
disc to disc; when it is activated, playback will be
prohibited if the software’s level is higher than the user-set
level.
Hybrid Super Audio CD Disc
CD layer that plays on any
CD player
1
High Density layer containing:
- High Quality DSD Stereo
2
■ Playback control (PBC)
An on-screen menu recorded on a Video CD or SVCD that
enables interactive playback and searching.
- High Quality DSD Multi-
channel
3
■ Progressive Scan
A method of displaying all scanning lines in a frame at
once, reducing flicker noticeable on a larger screen and
creating a sharp and smooth image.
43 En
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS
PLAYBACK SYSTEM
TV STANDARD
• DVD-Video
• Number of lines........................................PAL: 625, NTSC: 525
• Vertical frequency............................ PAL: 50 Hz, NTSC: 60 Hz
• Playback..........................................Multistandard (PAL/NTSC)
• DVD-Audio
• DVD-R, DVD-RW
• DVD+R, DVD+RW, DVD+R DL
• Video CD, SVCD
• SA-CD multi-channel and SA-CD stereo
• CD
CONNECTIONS
• Video output.................................................... 1 (Cinch: yellow)
• S-video output............................................ 1 (Mini DIN, 4 pins)
• Component video output
• PICTURE CD
• CD-R, CD-RW
Y output.......................................................... 1 (Cinch: green)
PB/CB output .................................................... 1 (Cinch: blue)
PR/CR output ...................................................... 1 (Cinch: red)
VIDEO PERFORMANCE
• SCART (U.K., Europe, and Russia models only)
• Video (CVBS) output ................................... 1 Vpp into 75 ohm
........................................................................ 1 (Euroconnector)
• S-video output.......................................... Y: 1 Vpp into 75 ohm
C: 0.3 Vpp into 75 ohm
• Digital output
Coaxial ......................................................... 1 (Cinch: orange)
Optical..................................1 (IEC 60958 for CDDA/LPCM,
IEC 61937 for MPEG 1/2, Dolby Digital, DTS)
HDMI......................................................................1 (Type A)
• Component video output.......................... Y: 1 Vpp into 75 ohm
PB/CB, PR/CR: 0.7 Vpp into 75 ohm
• RGB (SCART) output
(U.K., Europe, and Russia models only)
.................................................................... 0.7 Vpp into 75 ohm
• 2 channel analog output (L+R) ............1 pair (Cinch: white/red)
• 6 channel analog output
• Black level shift
(U.S.A. models only) .......................................................On/Off
Audio Front L/R................................1 pair (Cinch: white/red)
Audio Surround L/R..........................1 pair (Cinch: white/red)
Audio Center...................................................1 (Cinch: black)
Audio Subwoofer ............................................1 (Cinch: black)
AUDIO FORMAT
• Digital
Dolby Digital / DTS / MPEG....................Compressed Digital
PCM ........................ 16, 20, 24 bits / fs 44.1, 48, 88.2, 96 kHz
MP3 (ISO 9660)
.................. 32–320 kbps / fs 16, 22.05, 24, 32, 44.1, 48 kHz
WMA ............................................ 64–320 kbps, mono, stereo
CABINET
• Dimensions (W x D x H) .......................... 435 x 284.5 x 87 mm
(17–1/8 x 11–3/16 x 3–7/16 inch)
• Weight............................................ Approx. 3.3 kg (7 lbs. 4 oz.)
• Full decoding of Dolby Digital and DTS multi-channel sound
• Analog stereo sound
POWER SUPPLY
• Dolby surround compatible downmix from Dolby Digital multi-
channel sound
• Power inlet
U.S.A. and Canada models .......................... AC 120 V, 60 Hz
U.K. and Europe models.............................. AC 230 V, 50 Hz
Korea and Taiwan models............... AC 100–240 V, 50/60 Hz
Asia model ...................................... AC 100–240 V, 50/60 Hz
Russia model................................................ AC 230 V, 50 Hz
• Power consumption...............................................Approx. 21 W
• Power consumption (standby).............................less than 0.5 W
AUDIO PERFORMANCE
• DA Converter......................................................24 bit, 192 kHz
• Signal-Noise (1 kHz) .......................................................115 dB
• Dynamic range (1 kHz)....................................................105 dB
• DVD......................................................fs 96 kHz, 2 Hz–44 kHz
fs 48 kHz, 2 Hz–22 kHz
• SVCD....................................................fs 48 kHz, 2 Hz–22 kHz
fs 44.1 kHz, 2 Hz–20 kHz
Specifications are subject to change without prior notice.
• CD/VCD ............................................fs 44.1 kHz, 2 Hz–20 kHz
• Distortion and Noise (1 kHz).......................................... 0.002%
44 En
Download from Www.Somanuals.com. All Manuals Search And Download.
CARACTÉRISTIQUES TECHNIQUES
SYSTEME DE LECTURE
STANDARD TV
• DVD-Vidéo
• Nombre de lignes.....................................PAL: 625, NTSC: 525
• DVD-Audio
• Fréquence verticale .......................... PAL: 50 Hz, NTSC: 60 Hz
• Lecture ..........................................Multistandards (PAL/NTSC)
• DVD-R, DVD-RW
• DVD+R, DVD+RW, DVD+R DL
• Vidéo CD, SVCD
• SA-CD multicanaux et SA-CD stéréo
• CD
RACCORDEMENTS
• Sortie vidéo ........................................................1 (Cinch: jaune)
• Sortie S-vidéo........................................1 (Mini DIN, 4 broches)
• Sortie vidéo composante
• CD D’IMAGES
• CD-R, CD-RW
Sortie Y .............................................................1 (Cinch: vert)
Sortie PB/CB .................................................... 1 (Cinch: bleu)
Sortie PR/CR ................................................... 1 (Cinch: rouge)
PERFORMANCES VIDEO
• Sortie vidéo (CVBS)......................................1 Vcc sur 75 ohms
• Péritel (Modèles pour le Royaume-Uni,
l’Europe et la Russie seulement)
.............................................................................1 (Prise péritel)
• Sortie S-vidéo............................................Y: 1 Vcc sur 75 ohms
C: 0,3 Vcc sur 75 ohms
• Sortie vidéo composante...........................Y: 1 Vcc sur 75 ohms
PB/CB, PR/CR: 0,7 Vcc sur 75 ohms
• Sortie numérique
Coaxiale ....................................................... 1 (Cinch: orange)
Optique.............................. 1 (IEC 60958 pour CDDA/LPCM,
IEC 61937 pour MPEG 1/2, Dolby Digital, DTS)
HDMI......................................................................1 (Type A)
• Sortie RGB (Péritel)
(Modèle pour le Royaume-Uni, l’Europe et la Russie seulement)
.....................................................................0,7 Vcc sur 75 ohms
• Réglage de niveau du noir
(Modèles pour les États-Unis) .......................................Oui/Non
• Sortie analogique 2 canaux (G+D)
........................................................ 1 paire (Cinch: blanc/rouge)
• Sortie analogique 6 canaux
FORMAT AUDIO
Audio avant G/D ......................... 1 paire (Cinch: blanc/rouge)
Audio ambiance G/D .................. 1 paire (Cinch: blanc/rouge)
Audio Centre.....................................................1 (Cinch: noir)
Audio Caisson de graves...................................1 (Cinch: noir)
• Numérique
Dolby Digital / DTS / MPEG................Numérique compressé
PCM ........................ 16, 20, 24 bits / fs 44,1, 48, 88,2, 96 kHz
MP3 (ISO 9660)
................. 32 –320 kbps / fs 16, 22,05, 24, 32, 44,1, 48 kHz
WMA ............................................ 64–320 kbps, mono, stéréo
CABINET
• Décodage complet du son multicanaux Dolby Digital et DTS
• Son stéréo analogique
• Dimensions (L x P x H) ............................ 435 x 284,5 x 87 mm
• Poids.................................................................... Approx. 3,3 kg
• Mixage compatible avec le Dolby Surround à partir d’un son
multicanaux Dolby Digital
ALIMENTATION
• Prise d’alimentation commutée
PERFORMANCES AUDIO
Modèles pour le Canada et les États-Unis ... CA 120 V, 60 Hz
Modèles pour l’Europe, y compris le Royaume-Uni.... CA 230 V, 50 Hz
Modèles pour la Corée et Taïwan.... CA 100–240 V, 50/60 Hz
Modèle pour l’Asie ......................... CA 100–240 V, 50/60 Hz
Modèle pour la Russie................................. CA 230 V, 50 Hz
• Consommation......................................................Approx. 21 W
• Consommation (veille)................................... inférieure à 0,5 W
• Convertisseur NA.............................................. 24 bits, 192 kHz
• Rapport Signal sur Bruit (1 kHz) ....................................115 dB
• Plage dynamique (1 kHz).................................................105 dB
• DVD......................................................fs 96 kHz, 2 Hz–44 kHz
fs 48 kHz, 2 Hz–22 kHz
• SVCD....................................................fs 48 kHz, 2 Hz–22 kHz
fs 44,1 kHz, 2 Hz–20 kHz
• CD/VCD ............................................fs 44,1 kHz, 2 Hz–20 kHz
• Distorsion et Bruit (1 kHz) ............................................. 0,002%
Les caractéristiques peuvent être modifiées sans préavis.
© 2007
All rights reserved.
CQX1A1275Z
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A.
YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA
YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, GERMANY
YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE
YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND
YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN
YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
|