Read this manual carefully before operating this vehicle.
OWNER’S MANUAL
FZS10Y(C)
LIT-11626-22-36
3C3-28199-13
Download from Www.Somanuals.com. All Manuals Search And Download.
EAU10042
Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
EAU10081
Congratulations on your purchase of the Yamaha FZS10Y(C). This model is the result of Yamaha’s vast experience in the
production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you
have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at
the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most cur-
rent product information available at the time of printing, there may be minor discrepancies between your motorcycle and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.
EWA10011
WARNING
Please read this manual and the “YOU AND YOUR MOTORCYCLE: RIDING TIPS” booklet carefully before operating
this motorcycle. Do not attempt to operate this motorcycle until you have attained adequate knowledge of its con-
trols and operating features. Regular inspections and careful maintenance, along with good operating techniques,
will help ensure that you safely enjoy the capabilities and reliability of this motorcycle.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT MANUAL INFORMATION
EAU10132
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
WARNING
A NOTICE indicates special precautions that must be taken to avoid damage to the
vehicle or other property.
NOTICE
TIP
A TIP provides key information to make procedures easier or clearer.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT MANUAL INFORMATION
EAU10193
FZS10Y(C)
OWNER’S MANUAL
©2008 by Yamaha Motor Corporation, U.S.A.
1st edition, May 2008
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan.
P/N LIT-11626-22-36
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
LOCATION OF IMPORTANT
LABELS .............................................1-1
Tires ............................................. 7-18
Cast wheels ................................. 7-20
Adjusting the clutch lever free
FOR YOUR SAFETY –
SAFETY INFORMATION ..................2-1
PRE-OPERATION CHECKS .............5-1
Pre-operation check list ..................5-2
play ........................................... 7-20
Adjusting the rear brake light
DESCRIPTION ..................................3-1
Left view ..........................................3-1
Right view........................................3-2
Controls and instruments.................3-3
switch ....................................... 7-21
Checking the front and rear
OPERATION AND IMPORTANT
RIDING POINTS.................................6-1
Starting the engine .........................6-1
Shifting ...........................................6-2
Engine break-in ..............................6-4
Parking ...........................................6-4
brake pads ................................ 7-21
Checking the brake fluid level ...... 7-22
Changing the brake fluid .............. 7-23
Drive chain slack .......................... 7-23
Cleaning and lubricating the
Checking and lubricating the
cables ....................................... 7-25
Checking and lubricating the
throttle grip and cable ............... 7-25
Checking and lubricating the
brake and shift pedals .............. 7-26
Checking and lubricating the
brake and clutch levers ............ 7-26
Checking and lubricating the
centerstand and sidestand ....... 7-27
Checking the front fork ................. 7-28
Checking the steering .................. 7-28
Checking the wheel bearings ....... 7-29
Battery ......................................... 7-29
Replacing the fuses ..................... 7-30
Replacing a headlight bulb .......... 7-32
Replacing the tail/brake light
INSTRUMENT AND CONTROL
FUNCTIONS.......................................4-1
Indicator and warning lights ............4-2
Multi-function meter unit .................4-5
Clutch lever ...................................4-10
Shift pedal .....................................4-11
Brake pedal ..................................4-11
Fuel tank cap ................................4-12
Fuel ...............................................4-12
Catalytic converters ......................4-14
Seats ............................................4-14
Storage compartment ...................4-16
Adjusting the front fork ..................4-16
Adjusting the shock absorber
PERIODIC MAINTENANCE AND
ADJUSTMENT...................................7-1
Owner’s tool kit ...............................7-2
Periodic maintenance chart for the
General maintenance and
lubrication chart ..........................7-4
Removing and installing panels .....7-8
Checking the spark plugs ...............7-9
Canister (for California only) ........7-10
Engine oil and oil filter cartridge ...7-10
Coolant .........................................7-13
Replacing the air filter element .....7-15
Checking the engine idling
assembly ...................................4-18
Luggage strap holders ..................4-20
EXUP system ...............................4-20
Sidestand ......................................4-21
speed ........................................7-17
Checking the throttle cable free
play ...........................................7-17
Valve clearance ............................7-17
bulb ........................................... 7-33
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Replacing a turn signal light
bulb ...........................................7-33
Replacing the license plate light
bulb ...........................................7-34
Front wheel ...................................7-35
Rear wheel ...................................7-36
Troubleshooting ............................7-37
Troubleshooting charts .................7-39
MOTORCYCLE CARE AND
STORAGE..........................................8-1
Matte color caution .........................8-1
Storage ...........................................8-3
SPECIFICATIONS .............................9-1
CONSUMER INFORMATION...........10-1
Identification numbers ..................10-1
Reporting safety defects ...............10-3
Motorcycle noise regulation ..........10-4
Maintenance record ......................10-5
YAMAHA MOTOR
CORPORATION, U.S.A.
STREET AND ENDURO
MOTORCYCLE LIMITED
WARRANTY .............................10-7
YAMAHA EXTENDED SERVICE
(Y.E.S.) .....................................10-9
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF IMPORTANT LABELS
EAU10383
Read and understand all of the labels on your vehicle. They contain important information for safe and proper operation of
your vehicle. Never remove any labels from your vehicle. If a label becomes difficult to read or comes off, a replacement label
is available from your Yamaha dealer.
1
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATION OF IMPORTANT LABELS
1
2
4
NOTICE
1
Cleaning with alkaline or
acid cleaner, gasoline or
solvent will damage
windshield.
Use neutral detergent.
4B5-2815K-00
5
California only
6
as follows.
7
3
1-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
EAU10283
Safe Riding
• Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
Perform the pre-operation checks each
time you use the vehicle to make sure it
is in safe operating condition. Failure to
inspect or maintain the vehicle properly
increases the possibility of an accident
or equipment damage. See page 5-1
for a list of pre-operation checks.
G This motorcycle is designed to car-
ry the operator and a passenger.
G The failure of motorists to detect
and recognize motorcycles in traf-
fic is the predominating cause of
automobile/motorcycle accidents.
Many accidents have been caused
by an automobile driver who did
not see the motorcycle. Making
yourself conspicuous appears to
be very effective in reducing the
chance of this type of accident.
Be a Responsible Owner
G Many accidents involve inexperi-
enced operators. In fact, many op-
erators who have been involved in
accidents do not even have a cur-
rent motorcycle license.
As the vehicle’s owner, you are respon-
sible for the safe and proper operation
of your motorcycle.
Motorcycles are single-track vehicles.
Their safe use and operation are de-
pendent upon the use of proper riding
techniques as well as the expertise of
the operator. Every operator should
know the following requirements before
riding this motorcycle.
2
• Make sure that you are qualified
and that you only lend your
motorcycle to other qualified op-
erators.
• Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
• We recommend that you prac-
tice riding your motorcycle
where there is no traffic until you
have become thoroughly famil-
iar with the motorcycle and all of
its controls.
He or she should:
G Obtain thorough instructions from
a competent source on all aspects
of motorcycle operation.
G Observe the warnings and mainte-
nance requirements in this Own-
er’s Manual.
G Obtain qualified training in safe
and proper riding techniques.
G Obtain professional technical ser-
vice as indicated in this Owner’s
Manual and/or when made neces-
sary by mechanical conditions.
Therefore:
• Wear a brightly colored jacket.
• Use extra caution when you are
approaching
through intersections, since in-
tersections are the most likely
places for motorcycle accidents
to occur.
G Many accidents have been caused
by error of the motorcycle opera-
tor. A typical error made by the op-
erator is veering wide on a turn
and
passing
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
due to excessive speed or under-
cornering (insufficient lean angle
for the speed).
G This motorcycle is designed for on-
road use only. It is not suitable for
off-road use.
G A passenger should also observe
the above precautions.
• Always obey the speed limit and
Avoid Carbon Monoxide Poisoning
never travel faster than warrant- Protective apparel
All engine exhaust contains carbon
ed by road and traffic conditions. The majority of fatalities from motor- monoxide, a deadly gas. Breathing car-
• Always signal before turning or cycle accidents are the result of head bon monoxide can cause headaches,
changing lanes. Make sure that injuries. The use of a safety helmet is dizziness, drowsiness, nausea, confu-
2
other motorists can see you.
G The posture of the operator and vention or reduction of head injuries.
the single most critical factor in the pre- sion, and eventually death.
Carbon Monoxide is a colorless, odor-
passenger is important for proper
control.
G Always wear an approved helmet. less, tasteless gas which may be
G Wear a face shield or goggles. present even if you do not see or smell
Wind in your unprotected eyes any engine exhaust. Deadly levels of
could contribute to an impairment carbon monoxide can collect rapidly
of vision that could delay seeing a and you can quickly be overcome and
• The operator should keep both
hands on the handlebar and
both feet on the operator foot-
rests during operation to main-
tain control of the motorcycle.
• The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
G Never ride under the influence of
alcohol or other drugs.
hazard.
unable to save yourself. Also, deadly
G The use of a jacket, heavy boots, levels of carbon monoxide can linger
trousers, gloves, etc., is effective in for hours or days in enclosed or poorly
preventing or reducing abrasions ventilated areas. If you experience any
or lacerations.
symptoms of carbon monoxide poison-
G Never wear loose-fitting clothes, ing, leave the area immediately, get
otherwise they could catch on the fresh air, and SEEK MEDICAL TREAT-
control levers, footrests, or wheels MENT.
and cause injury or an accident.
G Always wear protective clothing
that covers your legs, ankles, and
feet. The engine or exhaust sys-
tem become very hot during or af-
ter operation and can cause burns.
G Do not run engine indoors. Even if
you try to ventilate engine exhaust
with fans or open windows and
doors, carbon monoxide can rap-
idly reach dangerous levels.
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
G Do not run engine in poorly venti-
• Never attach any large or heavy
items to the handlebar, front
fork, or front fender. These
items, including such cargo as
sleeping bags, duffel bags, or
tents, can create unstable han-
dling or a slow steering re-
sponse.
Maximum load:
FZS10Y 190 kg (419 lb)
FZS10YC 189 kg (417 lb)
lated or partially enclosed areas
such as barns, garages, or car-
ports.
When loading within this weight limit,
keep the following in mind:
G Do not run engine outdoors where
engine exhaust can be drawn into
a building through openings such
as windows and doors.
2
G Cargo and accessory weight
should be kept as low and close to
the motorcycle as possible. Se-
curely pack your heaviest items as
close to the center of the vehicle as
possible and make sure to distrib-
ute the weight as evenly as possi-
ble on both sides of the motorcycle
to minimize imbalance or instabili-
ty.
G Shifting weights can create a sud-
den imbalance. Make sure that ac-
cessories and cargo are securely
attached to the motorcycle before
riding. Check accessory mounts
and cargo restraints frequently.
• Properly adjust the suspension
for your load (suspension-ad-
justable models only), and
check the condition and pres-
sure of your tires.
G This vehicle is not designed to
pull a trailer or to be attached to
a sidecar.
Loading
Adding accessories or cargo to your
motorcycle can adversely affect stabili-
ty and handling if the weight distribution
of the motorcycle is changed. To avoid
the possibility of an accident, use ex-
treme caution when adding cargo or
accessories to your motorcycle. Use
extra care when riding a motorcycle
that has added cargo or accessories.
Here, along with the information about
accessories below, are some general
guidelines to follow if loading cargo to
your motorcycle:
Genuine Yamaha Accessories
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are avail-
able only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection to
Yamaha manufacture parts and acces-
sories or offer other modifications for
Yamaha vehicles. Yamaha is not in a
position to test the products that these
The total weight of the operator, pas-
senger, accessories and cargo must
not exceed the maximum load limit.
Operation of an overloaded vehicle
could cause an accident.
aftermarket
companies
produce.
Therefore, Yamaha can neither en-
dorse nor recommend the use of ac-
cessories not sold by Yamaha or
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
modifications not specifically recom-
mended by Yamaha, even if sold and
installed by a Yamaha dealer.
clearance or cornering clearance,
limit suspension travel, steering
travel or control operation, or ob-
scure lights or reflectors.
• Accessories fitted to the handle-
bar or the front fork area can
create instability due to improper
weight distribution or aerody-
namic changes. If accessories
are added to the handlebar or
front fork area, they must be as
tor and may limit control ability,
therefore, such accessories are
not recommended.
G Use caution when adding electri-
cal accessories. If electrical acces-
sories exceed the capacity of the
motorcycle’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
Aftermarket Parts, Accessories, and
Modifications
2
While you may find aftermarket prod-
ucts similar in design and quality to
genuine Yamaha accessories, recog-
nize that some aftermarket accessories
or modifications are not suitable be-
cause of potential safety hazards to you
or others. Installing aftermarket prod-
ucts or having other modifications per-
formed to your vehicle that change any
of the vehicle’s design or operation
characteristics can put you and others
at greater risk of serious injury or death.
You are responsible for injuries related
to changes in the vehicle.
Keep the following guidelines in mind,
as well as those provided under “Load-
ing” when mounting accessories.
G Never install accessories or carry
cargo that would impair the perfor-
mance of your motorcycle. Care-
fully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
lightweight as possible and Aftermarket Tires and Rims
should be kept to a minimum. The tires and rims that came with your
• Bulky or large accessories may motorcycle were designed to match the
seriously affect the stability of performance capabilities and to provide
the motorcycle due to aerody- the best combination of handling, brak-
namic effects. Wind may at- ing, and comfort. Other tires, rims, siz-
tempt to lift the motorcycle, or es, and combinations may not be
the motorcycle may become un- appropriate. Refer to page 7-18 for tire
stable in cross winds. These ac- specifications and more information on
cessories may also cause replacing your tires.
instability when passing or being
passed by large vehicles.
• Certain accessories can dis-
place the operator from his or
her normal riding position. This
improper position limits the free-
dom of movement of the opera-
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
EAU10410
Left view
3
1. Front fork spring preload adjusting bolt (page 4-16)
2. Front fork compression damping force adjusting screw (page 4-16)
3. Air filter element (page 7-15)
4. Main fuse (page 7-30)
5. Fuel injection system fuse (page 7-30)
9. Shock absorber assembly rebound damping force adjusting screw
(page 4-18)
10.Shift pedal (page 4-11)
11.Engine oil drain bolt (page 7-10)
12.Engine oil filter cartridge (page 7-10)
6. Storage compartment (page 4-16)
7. Passenger seat lock (page 4-14)
8. Shock absorber assembly spring preload adjusting ring (page 4-18)
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
EAU10420
Right view
3
1. Owner’s tool kit (page 7-2)
9. Engine oil level check window (page 7-10)
2. Rider seat lock lever (page 4-14)
3. Fuse box (page 7-30)
4. Battery (page 7-29)
5. Rear brake fluid reservoir (page 7-22)
6. Engine oil filler cap (page 7-10)
7. Front brake fluid reservoir (page 7-22)
8. Front fork rebound damping force adjusting screw (page 4-16)
10.Brake pedal (page 4-11)
11.Coolant reservoir (page 7-13)
12.Rear brake light switch (page 7-21)
13.Luggage strap holder (page 4-20)
3-2
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
EAU10430
Controls and instruments
3
1. Clutch lever (page 4-10)
2. Left handlebar switches (page 4-9)
3. Main switch/steering lock (page 4-1)
4. Multi-function meter unit (page 4-5)
5. Right handlebar switches (page 4-9)
6. Throttle grip (page 7-17)
7. Brake lever (page 4-11)
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU10661
Main switch/steering lockEAU10460
To lock the steering
OFF
All electrical systems are off. The key
can be removed.
EWA10061
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident.
4
1. Push.
2. Turn.
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
EAU10681
LOCK
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” po-
sition, and then turn it to “LOCK”
while still pushing it.
The steering is locked, and all electrical
systems are off. The key can be re-
moved.
EAU26900
ON
3. Remove the key.
All electrical circuits are supplied with
power, and the meter lighting, taillight,
license plate light and position lights
come on, and the engine can be start-
ed. The key cannot be removed.
TIP
The headlights come on automatically
when the engine is started and stay on
until the key is turned to “OFF”, even if
the engine stalls.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU11003
EAU11080
To unlock the steering
High beam indicator light “
”
Indicator and warning lights
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU11252
Oil level warning light “
”
This warning light comes on if the en-
gine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.
4
1. Push.
2. Turn.
1. Left turn signal indicator light “
2. Right turn signal indicator light “
”
”
”
Push the key in, and then turn it to
“OFF” while still pushing it.
3. Neutral indicator light “
”
4. High beam indicator light “
”
5. Engine trouble warning light “
6. Oil level warning light “
”
7. Coolant temperature warning light “
”
TIP
G Even if the oil level is sufficient, the
warning light may flicker when
riding on a slope or during sudden
acceleration or deceleration, but
this is not a malfunction.
G This model is also equipped with a
self-diagnosis device for the oil
level detection circuit. If a problem
is detected in the oil level detection
circuit, the following cycle will be
repeated until the malfunction is
EAU11030
Turn signal indicator lights “
”
and “
”
The corresponding indicator light flash-
es when the turn signal switch is
pushed to the left or right.
EAU11060
Neutral indicator light “
”
This indicator light comes on when the
transmission is in the neutral position.
4-2
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
corrected: The oil level warning
light will flash ten times, then go off
for 2.5 seconds. If this occurs,
have a Yamaha dealer check the
vehicle.
G For radiator-fan-equipped vehi-
cles, the radiator fan(s) automati-
cally switch on or off according to
the coolant temperature in the ra-
diator.
EAU11425
G If the engine overheats, see page
7-39 for further instructions.
Coolant temperature warning
light “
”
This warning light comes on if the en-
gine overheats. If this occurs, stop the
engine immediately and allow the en-
gine to cool.
4
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir-
cuit.
ECA10021
NOTICE
Do not continue to operate the en-
gine if it is overheating.
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
Coolant
temperature
Display
Conditions
What to do
Under 39 °C
(Under 103 °F)
Message “Lo” is displayed.
OK. Go ahead with riding.
40–116 °C
(104–242 °F)
Temperature is displayed.
OK. Go ahead with riding.
4
Stop the vehicle and allow it to idle until
Temperature display flashes. the coolant temperature goes down.
117–139 °C
(243–283 °F)
Warning light comes on.
If the temperature does not go down,
stop the engine. (See page 7-39.)
Above 140 °C
(Above 284 °F)
Message “HI” flashes.
Warning light comes on.
Stop the engine and allow it to cool.
(See page 7-39.)
4-4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU11532
EAU40176
The multi-function meter unit is
equipped with the following:
Engine trouble warning light “
”
Multi-function meter unit
This warning light comes on or flashes
if a problem is detected in the electrical
circuit monitoring the engine. If this oc-
curs, have a Yamaha dealer check the
self-diagnosis system. (See page 4-8
for an explanation of the self-diagnosis
device.)
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. If the warning light does not come
on for a few seconds, then go off, have
a Yamaha dealer check the electrical
circuit.
G a speedometer (which shows the
riding speed)
G a tachometer (which shows engine
speed)
G an odometer (which shows the to-
tal distance traveled)
G two tripmeters (which show the
distance traveled since they were
last set to zero)
G a fuel reserve tripmeter (which
shows the distance traveled since
the left segment of the fuel meter
started flashing)
G a clock
G a fuel meter
4
1. Coolant temperature display/air intake tem-
perature display
2. Speedometer
3. Tachometer
4. Odometer/tripmeter/fuel reserve tripmeter
5. “SELECT” button
6. “RESET” button
7. Clock
G a coolant temperature display
G an air intake temperature display
G a self-diagnosis device
G an LCD and tachometer bright-
ness control mode
8. Fuel meter
EWA12422
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
TIP
G Be sure to turn the key to “ON” be-
fore using the “SELECT” and “RE-
SET” buttons.
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
ECA10031
G To switch the speedometer and
2. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
3. When the hour digits start flashing,
push the “RESET” button to set the
hours.
NOTICE
odometer/tripmeter displays be-
tween kilometers and miles, press
the “SELECT” button for at least
one second.
Do not operate the engine in the ta-
chometer red zone.
Red zone: 12000 r/min and above
4. Push the “SELECT” button, and
the minute digits will start flashing.
5. Push the “RESET” button to set
the minutes.
Clock
Tachometer
6. Push the “SELECT” button and
then release it to start the clock.
4
Odometer and tripmeter modes
1. Clock
1. Tachometer
2. Tachometer red zone
The clock displays when the key is
turned to “ON”. In addition, the clock
can be displayed for 10 seconds by
pushing the “SELECT” button when the
main switch is in the “OFF” or “LOCK”
position.
The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the ta-
chometer needle will sweep once
across the r/min range and then return
to zero r/min in order to test the electri-
cal circuit.
1. Odometer/tripmeter/fuel reserve tripmeter
To set the clock
1. Turn the key to “ON”.
4-6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
Push the “SELECT” button to switch Fuel meter
mately 3 seconds. If this occurs, have a
Yamaha dealer check the electrical cir-
cuit.
the display between the odometer
mode “ODO” and the tripmeter modes
“TRIP A” and “TRIP B” in the following
order:
Coolant temperature mode
TRIP A → TRIP B → ODO → TRIP A
When the fuel amount in the fuel tank
decreases to 3.4 L (0.90 US gal,
0.75 Imp.gal), the left segment of the
fuel meter will start flashing, and the
odometer display will automatically
change to the fuel reserve tripmeter
mode “F-TRIP” and start counting the
distance traveled from that point. In that
case, push the “SELECT” button to
switch the display between the various
tripmeter and odometer modes in the
following order:
4
1. Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display seg-
ments of the fuel meter disappear to-
wards “E” (Empty) as the fuel level 1. Coolant temperature display
decreases. When the last segment on
The coolant temperature display indi-
the left starts flashing, refuel as soon as
possible.
cates the temperature of the coolant.
Push the “RESET” button to switch the
coolant temperature display to the air
F-TRIP → TRIP A → TRIP B → ODO
→ F-TRIP
TIP
To reset a tripmeter, select it by push-
ing the “SELECT” button, and then
push the “RESET” button for at least
one second. If you do not reset the fuel
reserve tripmeter manually, it will reset
itself automatically and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).
This fuel meter is equipped with a self- intake temperature display.
diagnosis system. If a problem is de-
tected in the electrical circuit, the follow-
TIP
When the coolant temperature display
ing cycle will be repeated until the
malfunction is corrected: “E” (Empty),
“F” (Full) and symbol “ ” will flash
eight times, then go off for approxi-
is selected, “C” is displayed for one
second, and then the coolant tempera-
ture is displayed.
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
ECA10021
G When the key is turned to “ON”, If a problem is detected in any of those
NOTICE
the coolant temperature is auto- circuits, the engine trouble warning light
matically displayed, even if the air will come on and the display will indi-
intake temperature was displayed cate a two-digit error code.
Do not continue to operate the en-
gine if it is overheating.
prior to turning the key to “OFF”.
If the display indicates any error codes,
G When the air intake temperature note the code number, and then have a
display is selected, “A” is displayed Yamaha dealer check the vehicle.
Air intake temperature mode
ECA11590
for one second, and then the air in-
NOTICE
take temperature is displayed.
If the display indicates an error
code, the vehicle should be checked
as soon as possible in order to avoid
engine damage.
4
Self-diagnosis device
1. Air intake temperature display
The air intake temperature display indi-
cates the temperature of the air drawn
into the air filter case. Push the “RE-
SET” button to switch the coolant tem-
perature display to the air intake
temperature display.
1. Error code display
This model is equipped with a self-diag-
nosis device for various electrical cir-
cuits.
TIP
G Even if the air intake temperature
is set to be displayed, the coolant
temperature warning light comes
on if the engine overheats.
4-8
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU12347
LCD and tachometer brightness
control mode
4. Push the “RESET” button to select
Handlebar switches
the desired brightness level.
5. Push the “SELECT” button to con-
firm the selected brightness level.
The display will return to the odom-
eter or tripmeter mode.
Left
4
1. Tachometer panel
2. Tachometer needle
3. LCD
1. Dimmer switch “
2. Turn signal switch “
/
”
/
”
3. Horn switch “
”
4. Brightness level
4. Hazard switch “
”
This function allows you to adjust the
brightness of the LCD and the tachom-
eter panel and needle to suit the out-
side lighting conditions.
Right
To set the brightness
1. Turn the key to “OFF”.
2. Push and hold the “SELECT” but-
ton.
3. Turn the key to “ON”, and then re-
lease the “SELECT” button after
five seconds.
1. Engine stop switch “
2. Start switch “
/
”
”
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU12400
EAU12711
EAU12820
Dimmer switch “
/
”
Start switch “
”
Clutch lever
Set this switch to “ ” for the high Push this switch to crank the engine
beam and to “ ” for the low beam.
with the starter. See page 6-1 for start-
ing instructions prior to starting the en-
gine.
EAU12460
Turn signal switch “
/
”
To signal a right-hand turn, push this
EAU41700
switch to “ ”. To signal a left-hand The engine trouble warning light will
turn, push this switch to “ ”. When re- come on when the key is turned to “ON”
leased, the switch returns to the center and the start switch is pushed, but this
position. To cancel the turn signal does not indicate a malfunction.
lights, push the switch in after it has re-
4
1. Clutch lever
EAU12765
turned to the center position.
Hazard switch “
”
The clutch lever is located at the left
With the key in the “ON” position, use handlebar grip. To disengage the
this switch to turn on the hazard lights clutch, pull the lever toward the handle-
(simultaneous flashing of all turn signal bar grip. To engage the clutch, release
EAU12500
Horn switch “
”
Press this switch to sound the horn.
lights).
the lever. The lever should be pulled
EAU12660
The hazard lights are used in case of rapidly and released slowly for smooth
an emergency or to warn other drivers clutch operation.
Engine stop switch “
/
”
Set this switch to “ ” before starting
the engine. Set this switch to “ ” to
stop the engine in case of an emergen-
cy, such as when the vehicle overturns
or when the throttle cable is stuck.
when your vehicle is stopped where it The clutch lever is equipped with a
might be a traffic hazard.
clutch switch, which is part of the igni-
tion circuit cut-off system. (See page
4-21.)
ECA10061
NOTICE
Do not use the hazard lights for an
extended length of time with the en-
gine not running, otherwise the bat-
tery may discharge.
4-10
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU12870
EAU26823
EAU12941
Shift pedal
Brake lever
Brake pedal
The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle-
bar grip.
4
1. Shift pedal
1. Brake pedal
The shift pedal is located on the left
side of the engine and is used in com-
bination with the clutch lever when
shifting the gears of the 6-speed con-
stant-mesh transmission equipped on
this motorcycle.
The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.
1. Brake lever
2. Brake lever position adjusting dial
3. “
” mark
4. Distance between brake lever and handlebar
grip
The brake lever is equipped with a
brake lever position adjusting dial. To
adjust the distance between the brake
lever and the handlebar grip, turn the
adjusting dial while holding the lever
pushed away from the handlebar grip.
Make sure that the appropriate setting
on the adjusting dial is aligned with
the “ ” mark on the brake lever.
4-11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU13074
EAU13221
TIP
Fuel tank cap
Fuel
The fuel tank cap cannot be closed un-
less the key is in the lock. In addition,
the key cannot be removed if the cap is
not properly closed and locked.
Make sure there is sufficient gasoline in
the tank.
EWA10881
WARNING
Gasoline and gasoline vapors are
extremely flammable. To avoid fires
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
EWA11091
WARNING
Make sure that the fuel tank cap is
properly closed after filling fuel.
4
Leaking fuel is a fire hazard.
1. Fuel tank cap lock cover
2. Unlock.
1. Before refueling, turn off the en-
gine and be sure that no one is sit-
ting on the vehicle. Never refuel
while smoking, or while in the vi-
cinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters and
clothes dryers.
2. Do not overfill the fuel tank. When
refueling, be sure to insert the
pump nozzle into the fuel tank filler
hole. Stop filling when the fuel
reaches the bottom of the filler
tube. Because fuel expands when
it heats up, heat from the engine or
the sun can cause fuel to spill out
of the fuel tank.
To open the fuel tank cap
Open the fuel tank cap lock cover, in-
sert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be re-
leased and the fuel tank cap can be
opened.
To close the fuel tank cap
1. Push the fuel tank cap into position
with the key inserted in the lock.
2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.
4-12
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
ately. If gasoline spills on your skin, um unleaded fuel. Use of unleaded fuel
wash with soap and water. If gaso- will extend spark plug life and reduce
line spills on your clothing, change maintenance costs.
your clothes.
Gasohol
There are two types of gasohol: gaso-
hol containing ethanol and that contain-
ing methanol. Gasohol containing
ethanol can be used if the ethanol con-
tent does not exceed 10% (E10). Gas-
ohol containing methanol is not
recommended by Yamaha because it
can cause damage to the fuel system
or vehicle performance problems.
EAU13301
Recommended fuel:
UNLEADED GASOLINE ONLY
Fuel tank capacity:
1. Fuel tank filler tube
2. Fuel level
4
18.0 L (4.76 US gal, 3.96 Imp.gal)
Fuel reserve amount:
3.4 L (0.90 US gal, 0.75 Imp.gal)
3. Wipe up any spilled fuel immedi-
ately. NOTICE: Immediately wipe
off spilled fuel with a clean, dry,
soft cloth, since fuel may deteri-
orate painted surfaces or plastic
ECA11400
NOTICE
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.
parts.
[ECA10071]
4. Be sure to securely close the fuel
tank cap.
EWA15151
WARNING
Your Yamaha engine has been de-
signed to use regular unleaded gaso-
line with a pump octane number
[(R+M)/2] of 86 or higher, or a research
octane number of 91 or higher. If
knocking (or pinging) occurs, use a
gasoline of a different brand or premi-
Gasoline is poisonous and can
cause injury or death. Handle gaso-
line with care. Never siphon gaso-
line by mouth. If you should swallow
some gasoline or inhale a lot of gas-
oline vapor, or get some gasoline in
your eyes, see your doctor immedi-
4-13
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU13444
ECA10701
EAU39322
Catalytic converters
Seats
NOTICE
This vehicle is equipped with catalytic
Use only unleaded gasoline. The use
of leaded gasoline will cause unre-
pairable damage to the catalytic
converter.
converters in the exhaust system.
Passenger seat
EWA10861
WARNING
To remove the passenger seat
1. Insert the key into the seat lock,
and then turn it counterclockwise.
The exhaust system is hot after op-
eration. To prevent a fire hazard or
burns:
G Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
4
G Park the motorcycle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.
G Make sure that the exhaust sys-
tem has cooled down before do-
ing any maintenance work.
G Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.
1. Passenger seat lock
2. Unlock.
2. Pull the passenger seat forward,
and then lift it up.
To install the passenger seat
1. Place the passenger seat in the
original position, and then push the
rear of the seat down to lock it in
place.
4-14
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
TIP
Make sure that the seats are properly
secured before riding.
1. Rider seat lock lever
2. Remove the key.
4
To install the rider seat
Rider seat
1. Insert the projection on the front of
the rider seat into the seat holder
as shown, and then push the rear
of the seat down to lock it in place.
To remove the rider seat
1. Remove the passenger seat.
2. Push the rider seat lock lever, lo-
cated under the back of the rider
seat, to the right as shown, and
then pull the seat off.
1. Projection
2. Seat holder
2. Install the passenger seat.
4-15
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU14461
EAU39333
EWA14670
Spring preload
Storage compartment
Adjusting the front fork
WARNING
Always adjust the spring preload on
both fork legs equally, otherwise
may result.
Each front fork leg is equipped with a
spring preload adjusting bolt, the right
front fork leg is equipped with a re-
bound damping force adjusting screw
and the left front fork leg with a com-
pression damping force adjusting
4
1. Spring preload adjusting bolt
1. Storage compartment
To increase the spring preload and
thereby harden the suspension, turn
the adjusting bolt on each fork leg in di-
rection (a). To decrease the spring pre-
The storage compartment is located
under the passenger seat. (See page
4-14.)
screw.
ECA10101
EWA10961
load
and
thereby
soften
the
NOTICE
WARNING
suspension, turn the adjusting bolt on
each fork leg in direction (b).
Align the appropriate groove on the ad-
justing mechanism with the top of the
front fork cap bolt.
do not attempt to turn beyond the
maximum or minimum settings.
G Do not exceed the load limit of 3
kg (7 lb) for the storage com-
partment.
G Do not exceed the maximum
load of FZS10Y 190 kg (419 lb)
FZS10YC 189 kg (417 lb) for the
vehicle.
4-16
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
Rebound damping force
Rebound damping setting:
Minimum (soft):
26 click(s) in direction (b)*
Standard:
18 click(s) in direction (b)*
Maximum (hard):
1 click(s) in direction (b)*
* With the adjusting screw fully turned
in direction (a)
1. Current setting
2. Front fork cap bolt
Compression damping force
4
1. Rebound damping force adjusting screw
The rebound damping force is adjusted
on the right front fork leg only. To in-
crease the rebound damping force and
thereby harden the rebound damping,
turn the adjusting screw in direction (a).
To decrease the rebound damping
force and thereby soften the rebound
damping, turn the adjusting screw in di-
rection (b).
Spring preload setting:
Minimum (soft):
8
Standard:
5.5
Maximum (hard):
0
1. Compression damping force adjusting screw
The compression damping force is ad-
justed on the left front fork leg only. To
increase the compression damping
force and thereby harden the compres-
sion damping, turn the adjusting screw
in direction (a). To decrease the com-
TIP
Be sure to perform this adjustment on
the right front fork leg.
4-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU39343
pression damping force and thereby ber of clicks of each damping force ad-
soften the compression damping, turn justing mechanism and to modify the
Adjusting the shock absorber
assembly
the adjusting screw in direction (b).
specifications as necessary.
This shock absorber assembly is
equipped with a spring preload adjust-
ing ring and a rebound damping force
TIP
Be sure to perform this adjustment on
the left front fork leg.
adjusting screw.
ECA10101
NOTICE
Compression damping setting:
Minimum (soft):
26 click(s) in direction (b)*
Standard:
5 click(s) in direction (b)*
Maximum (hard):
To avoid damaging the mechanism,
do not attempt to turn beyond the
maximum or minimum settings.
4
1 click(s) in direction (b)*
* With the adjusting screw fully turned
in direction (a)
Spring preload
TIP
Although the total number of clicks of a
damping force adjusting mechanism
may not exactly match the above spec-
ifications due to small differences in
production, the actual number of clicks
always represents the entire adjusting
range. To obtain a precise adjustment,
it would be advisable to check the num-
1. Spring preload adjusting ring
2. Special wrench
3. Position indicator
4-18
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
To increase the spring preload and Rebound damping force
TIP
thereby harden the suspension, turn
the adjusting ring in direction (a). To de-
crease the spring preload and thereby
soften the suspension, turn the adjust-
ing ring in direction (b).
To obtain a precise adjustment, it is ad-
visable to check the actual total number
of clicks or turns of the damping force
adjusting mechanism. This adjustment
range may not exactly match the spec-
ifications listed due to small differences
in production.
G Align the appropriate notch in the
adjusting ring with the position in-
dicator on the shock absorber.
G Use the special wrench included in
the owner’s tool kit to make the ad-
justment.
EWA10221
WARNING
4
1. Rebound damping force adjusting screw
This shock absorber assembly con-
tains highly pressurized nitrogen
gas. Read and understand the fol-
lowing information before handling
the shock absorber assembly.
G Do not tamper with or attempt to
open the cylinder assembly.
G Do not subject the shock ab-
sorber assembly to an open
flame or other high heat source.
This may cause the unit to ex-
plode due to excessive gas
pressure.
To increase the rebound damping force
and thereby harden the rebound damp-
ing, turn the adjusting screw in direction
(a). To decrease the rebound damping
force and thereby soften the rebound
damping, turn the adjusting screw in di-
rection (b).
Spring preload setting:
Minimum (soft):
1
Standard:
3
Maximum (hard):
7
Rebound damping setting:
Minimum (soft):
12 click(s) in direction (b)*
Standard:
8 click(s) in direction (b)*
Maximum (hard):
1 click(s) in direction (b)*
* With the adjusting screw fully turned
in direction (a)
G Do not deform or damage the
cylinder in any way. Cylinder
damage will result in poor
damping performance.
4-19
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU15151
EAU41940
G Do not dispose of a damaged or
Luggage strap holders
EXUP system
worn-out shock absorber as-
This model is equipped with Yamaha’s
EXUP (EXhaust Ultimate Power valve)
system. This system boosts engine
power by means of a valve that regu-
lates the diameter of the exhaust pipe.
The EXUP system valve is constantly
adjusted in accordance with the engine
speed by a computer-controlled servo-
sembly yourself. Take the shock
absorber assembly to a Yamaha
dealer for any service.
motor.
4
ECA15610
1. Luggage strap holder
NOTICE
There is a luggage strap holder on each
passenger footrest.
The EXUP system has been set and
extensively tested at the Yamaha
factory. Changing these settings
without sufficient technical knowl-
edge may result in poor perfor-
mance of or damage to the engine.
4-20
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
EAU15301
EAU44901
below and have a Yamaha dealer re-
pair it if it does not function proper-
ly.
Sidestand
Ignition circuit cut-off system
The ignition circuit cut-off system (com-
prising the sidestand switch, clutch
switch and neutral switch) has the fol-
lowing functions.
The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.
G It prevents starting when the trans-
mission is in gear and the side-
stand is up, but the clutch lever is
not pulled.
G It prevents starting when the trans-
mission is in gear and the clutch le-
ver is pulled, but the sidestand is
still down.
G It cuts the running engine when the
transmission is in gear and the sid-
estand is moved down.
Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.
TIP
The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)
4
EWA10240
WARNING
The vehicle must not be ridden with
the sidestand down, or if the side-
stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in
a
possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon-
sibility of raising the sidestand be-
fore starting off. Therefore, check
this system regularly as described
4-21
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUMENT AND CONTROL FUNCTIONS
WARNING
With the engine turned off:
1. Move the sidestand down.
2. Make sure that the engine stop switch is turned on.
3. Turn the key on.
4. Shift the transmission into the neutral position.
5. Push the start switch.
• The vehicle must be placed on the center-
stand during this inspection.
• If a malfunction is noted, have a Yamaha
dealer check the system before riding.
Does the engine start?
YES
NO
4
With the engine still running:
6. Move the sidestand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the sidestand down.
Does the engine stall?
The neutral switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
YES
NO
NO
The sidestand switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
After the engine has stalled:
10. Move the sidestand up.
11. Keep the clutch lever pulled.
12. Push the start switch.
Does the engine start?
The clutch switch may not be working correctly.
The motorcycle should not be ridden until
checked by a Yamaha dealer.
YES
The system is OK. The motorcycle can be ridden.
4-22
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY – PRE-OPERATION CHECKS
EAU15595
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.
EWA11151
WARNING
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
5
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY – PRE-OPERATION CHECKS
EAU15605
Pre-operation check list
ITEM
CHECKS
PAGE
• Check fuel level in fuel tank.
• Refuel if necessary.
Fuel
4-12
• Check fuel line for leakage.
• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
Engine oil
Coolant
7-10
7-13
• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
5
Front brake
7-21, 7-22
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add recommended brake fluid to specified level.
• Check hydraulic system for leakage.
Rear brake
Clutch
7-21, 7-22
• Check operation.
• Lubricate cable if necessary.
• Check lever free play.
• Adjust if necessary.
7-20
5-2
Download from Www.Somanuals.com. All Manuals Search And Download.
FOR YOUR SAFETY – PRE-OPERATION CHECKS
ITEM
CHECKS
PAGE
• Make sure that operation is smooth.
• Check cable free play.
• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
Throttle grip
7-17, 7-25
grip housing.
• Make sure that operation is smooth.
• Lubricate if necessary.
Control cables
Drive chain
7-25
• Check chain slack.
• Adjust if necessary.
• Check chain condition.
• Lubricate if necessary.
7-23, 7-24
• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.
Wheels and tires
7-18, 7-20
5
• Make sure that operation is smooth.
• Lubricate pedal pivoting points if necessary.
Brake and shift pedals
Brake and clutch levers
Centerstand, sidestand
Chassis fasteners
7-26
7-26
7-27
—
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
• Make sure that operation is smooth.
• Lubricate pivots if necessary.
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
Instruments, lights, signals
and switches
• Check operation.
• Correct if necessary.
—
• Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer check vehicle.
Sidestand switch
4-21
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND IMPORTANT RIDING POINTS
EAU15951
EAU45310
EAU40195
Starting the engine
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met.
G The transmission is in the neutral
position.
TIP
This model is equipped with a lean an-
gle sensor to stop the engine in case of
a turnover. To start the engine after a
turnover, be sure to turn the main
switch to “OFF” and then to “ON”. Fail-
ing to do so will prevent the engine from
starting even though the engine will
crank when pushing the start switch.
understand, ask your Yamaha dealer.
EWA10271
WARNING
G The transmission is in gear with
the clutch lever pulled and the sid-
estand up.
Failure to familiarize yourself with
the controls can lead to loss of con-
trol, which could cause an accident
or injury.
See page 4-21 for more informa-
tion.
1. Turn the key to “ON” and make
sure that the engine stop switch is
set to “ ”.
The following warning lights
should come on for a few seconds,
then go off.
6
G Oil level warning light
G Coolant temperature warning
light
G Engine trouble warning light
ECA15482
NOTICE
If a warning light does not go off, see
page 4-2 for the corresponding
warning light circuit check.
6-1
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND IMPORTANT RIDING POINTS
EAU16671
2. Shift the transmission into the neu-
tral position. (See page 6-2.) The
neutral indicator light should come
on. If not, ask a Yamaha dealer to
check the electrical circuit.
3. Start the engine by pushing the
mum engine life, always warm
the engine up before starting
off. Never accelerate hard when
G If the coolant temperature warn-
Shifting
ing light flickers or remains on
after starting, immediately stop
the engine, and then check the
coolant level and the vehicle for
coolant leakage. If necessary,
add coolant, and then check the
warning light again.
G If the engine trouble warning
light comes on after starting, im-
mediately stop the engine, and
the engine is cold!
[ECA11131]
1. Shift pedal
2. Neutral position
If the engine fails to start, release
the start switch, wait a few sec-
onds, and then try again. Each
starting attempt should be as short
as possible to preserve the bat-
tery. Do not crank the engine more
than 10 seconds on any one at-
have a Yamaha dealer check the
cause.
Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.
6
tempt.
ECA16110
NOTICE
TIP
To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.
G If the oil level warning light flick-
ers or remains on after starting,
immediately stop the engine,
and then check the engine oil
level and the vehicle for oil leak-
age. If necessary, add engine
oil, and then check the warning
light again.
6-2
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND IMPORTANT RIDING POINTS
ECA10260
4. At the recommended shift points
3. Shift the transmission into the neu-
tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.
NOTICE
shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.
5. Shift the transmission into second
gear. (Make sure not to shift the
transmission into the neutral posi-
tion.)
6. Open the throttle part way and
gradually release the clutch lever.
7. Follow the same procedure when
shifting to the next higher gear.
G Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.
EAU16740
Recommended shift points
The recommended shift points during
acceleration and deceleration are
shown in the table below.
Shift up points:
G Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.
1st → 2nd: 20 km/h (12.5 mi/h)
2nd → 3rd: 30 km/h (18.8 mi/h)
3rd → 4th: 40 km/h (25.0 mi/h)
4th → 5th: 50 km/h (31.3 mi/h)
5th → 6th: 60 km/h (37.5 mi/h)
Shift down points:
6th → 5th: 25 km/h (15.5 mi/h)
5th → 4th: 25 km/h (15.5 mi/h)
4th → 3rd: 25 km/h (15.5 mi/h)
3rd → 2nd: 25 km/h (15.5 mi/h)
2nd → 1st: 25 km/h (15.5 mi/h)
TIP
When shifting gears in normal operat-
ing conditions, use the recommended
shift points.
6
EAU16700
To decelerate
1. Apply both the front and the rear
EAU16681
To start out and accelerate
1. Pull the clutch lever to disengage
brakes to slow the motorcycle.
2. Shift the transmission into first
gear when the motorcycle reaches
25 km/h (15.5 mi/h). If the engine is
about to stall or runs very roughly,
pull the clutch lever in and use the
brakes to stop the motorcycle.
the clutch.
2. Shift the transmission into first
gear. The neutral indicator light
should go out.
3. Open the throttle gradually, and at
the same time, release the clutch
lever slowly.
6-3
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND IMPORTANT RIDING POINTS
EAU16841
EAU17213
1600 km (1000 mi) and beyond
The vehicle can now be operated nor-
Engine break-in
Parking
There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow-
ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt-
tle operation or any condition that might
result in engine overheating must be
avoided.
When parking, stop the engine, and
mally.
then remove the key from the main
ECA10310
switch.
NOTICE
EWA10311
G Keep the engine speed out of
the tachometer red zone.
G If any engine trouble should oc-
cur during the engine break-in
WARNING
G Since the engine and exhaust
system can become very hot,
park in a place where pedestri-
ans or children are not likely to
touch them and be burned.
G Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.
period, immediately have
Yamaha dealer check the vehi-
cle.
a
6
G Do not park near grass or other
flammable materials which
might catch fire.
EAU17092
0–1000 km (0–600 mi)
Avoid prolonged operation above 6000
r/min. NOTICE: After 1000 km (600
mi) of operation, the engine oil must
be changed and the oil filter car-
tridge or element replaced.
[ECA10302]
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 7200
r/min.
6-4
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17232
EAU17302
G A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
Periodic inspection, adjustment, and lu-
brication will keep your vehicle in the
safest and most efficient condition pos-
sible. Safety is an obligation of the vehi-
cle owner/operator. The most important
points of vehicle inspection, adjust-
ment, and lubrication are explained on
Emission controls not only function to
ensure cleaner air, but are also vital to
proper engine operation and maximum
performance. In the following periodic
maintenance charts, the services relat-
ed to emissions control are grouped
separately. These services require
specialized data, knowledge, and
equipment. Maintenance, replacement,
or repair of the emission control devic-
es and systems may be performed by
any repair establishment or individual
that is certified (if applicable). Yamaha
dealers are trained and equipped to
perform these particular services.
G Running the engine while ser-
vicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
the following pages.
death. See page 2-1 for more in-
EWA10321
formation about carbon monox-
WARNING
ide.
Failure to properly maintain the ve-
hicle or performing maintenance ac-
tivities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle ser-
vice, have a Yamaha dealer perform
service.
7
EWA15121
WARNING
Turn off the engine when performing
maintenance
specified.
unless
otherwise
7-1
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17491
Owner’s tool kit
1. Owner’s tool kit
The owner’s tool kit is located inside the
storage compartment under the pas-
senger seat. (See page 4-14.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. How-
ever, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.
7
TIP
If you do not have the tools or experi-
ence required for a particular job, have
a Yamaha dealer perform it for you.
7-2
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU17600
Periodic maintenance chart for the emission control system
INITIAL
ODOMETER READINGS
8000 mi 12000 mi 16000 mi
600 mi
4000 mi
20000 mi
No.
ITEM
ROUTINE
(1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km)
or
1 month
or
or
or
or
or
6 months 12 months 18 months 24 months 30 months
• Check fuel hoses for cracks or
damage.
• Replace if necessary.
1
*
*
Fuel line
√
√
√
√
√
√
√
√
• Check condition.
• Adjust gap and clean.
• Replace every 8000 mi (13000
km) or 12 months.
2
Spark plugs
Replace.
Replace.
• Check and adjust valve clearance
when engine is cold.
3
4
5
6
*
*
*
*
Valve clearance
Every 26600 mi (42000 km)
• Check breather hose for cracks or
damage.
• Replace if necessary.
Crankcase breather
system
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
7
• Check and adjust engine idle
speed and synchronization.
Fuel injection
√
• Check for leakage.
• Tighten if necessary.
• Replace gasket(s) if necessary.
Exhaust system
Evaporative emis-
sion control system
(For California only) • Replace if necessary.
• Check control system for dam-
age.
7
8
*
*
√
• Check the air cut-off valve, reed
valve, and hose for damage.
• Replace any damaged parts.
Air induction sys-
tem
√
√
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
7-3
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU32185
General maintenance and lubrication chart
INITIAL
600 mi
ODOMETER READINGS
8000 mi 12000 mi 16000 mi
4000 mi
20000 mi
No.
ITEM
ROUTINE
(1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km)
or
1 month
or
or
or
or
or
6 months 12 months 18 months 24 months 30 months
1
*
*
Air filter element
Clutch
• Replace.
Every 24000 mi (37000 km)
• Check operation.
• Adjust or replace cable.
2
3
√
√
√
√
√
√
√
√
√
√
√
√
• Check operation, fluid level, and
for fluid leakage.
• Replace brake pads if necessary.
*
*
Front brake
Rear brake
• Check operation, fluid level, and
for fluid leakage.
• Replace brake pads if necessary.
4
√
√
√
√
√
√
√
√
√
√
√
• Check for cracks or damage.
• Replace.
5
6
*
*
Brake hoses
Wheels
Every 4 years
7
• Check runout and for damage.
• Replace if necessary.
√
√
√
√
√
√
√
√
√
√
• Check tread depth and for dam-
age.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
7
*
Tires
• Check bearings for smooth oper-
ation.
• Replace if necessary.
8
9
*
*
Wheel bearings
√
√
√
√
√
√
√
√
√
√
Swingarm pivot
bearings
• Check bearing assemblies for
looseness.
7-4
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
INITIAL
ODOMETER READINGS
8000 mi 12000 mi 16000 mi
600 mi
4000 mi
20000 mi
No.
ITEM
ROUTINE
(1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km)
or
1 month
or
or
or
or
or
6 months 12 months 18 months 24 months 30 months
• Check chain slack, alignment and
condition.
• Adjust and lubricate chain with a
special O-ring chain lubricant
thoroughly.
10
Drive chain
Every 600 mi (1000 km) and after washing the motorcycle or riding in the rain
• Check bearing assemblies for
looseness.
• Moderately repack with lithium-
soap-based grease every 10000
mi (16000 km) or 18 months.
11 * Steering bearings
12 * Chassis fasteners
√
√
√
√
√
Repack.
√
√
√
√
• Check all chassis fitting and fas-
teners.
• Correct if necessary.
√
Brake lever pivot
shaft
13
• Apply silicone grease lightly.
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
7
Brake pedal pivot
shaft
• Apply lithium-soap-based grease
lightly.
14
Clutch lever pivot
shaft
• Apply lithium-soap-based grease
lightly.
15
Shift pedal pivot
shaft
• Apply lithium-soap-based grease
lightly.
16
• Check operation.
• Apply lithium-soap-based grease
lightly.
Centerstand and
17 *
√
√
√
√
√
√
√
√
√
√
sidestand pivots
• Check operation and replace if
necessary.
18 * Sidestand switch
√
7-5
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
INITIAL
ODOMETER READINGS
600 mi
4000 mi
8000 mi 12000 mi 16000 mi
20000 mi
No.
ITEM
ROUTINE
(1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km)
or
1 month
or
or
or
or
or
6 months 12 months 18 months 24 months 30 months
• Check operation and for oil leak-
age.
• Replace if necessary.
19 * Front fork
√
√
√
√
√
√
√
√
√
√
• Check operation and for oil leak-
age.
• Replace if necessary.
Shock absorber as-
20 *
sembly
Rear suspension
link pivots
• Check operation.
• Correct if necessary.
21 *
22
√
√
√
√
√
√
• Change (warm engine before
draining).
Engine oil
√
√
√
√
√
√
√
√
Engine oil filter car-
tridge
23 *
• Replace.
• Check hoses for cracks or dam-
age.
• Replace if necessary.
√
√
7
24 * Cooling system
• Change with ethylene glycol anti-
freeze coolant every 24 months.
Change.
Front and rear brake
switches
25 *
• Check operation.
√
√
√
√
√
√
√
√
√
√
√
√
• Apply Yamaha chain and cable
lube or engine oil thoroughly.
26 * Control cables
• Check operation and free play.
• Adjust the throttle cable free play
if necessary.
• Lubricate the throttle grip housing
and cable.
Throttle grip hous-
27 *
√
√
√
√
√
ing and cable
7-6
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
INITIAL
ODOMETER READINGS
8000 mi 12000 mi 16000 mi
600 mi
4000 mi
20000 mi
No.
ITEM
ROUTINE
(1000 km) (7000 km) (13000 km) (19000 km) (25000 km) (31000 km)
or
1 month
or
or
or
or
or
6 months 12 months 18 months 24 months 30 months
Lights, signals and
switches
• Check operation.
• Adjust headlight beam.
28 *
√
√
√
√
√
√
* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.
TIP
From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.
EAU17650
TIP
G Air filter
• This model’s air filter is equipped with a disposable oil-coated paper element, which must not be cleaned with com-
pressed air to avoid damaging it.
• The air filter element needs to be replaced more frequently when riding in unusually wet or dusty areas.
G Hydraulic brake service
7
• After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake fluid
levels and fill the reservoirs as required.
• Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.
• Replace the brake hoses every four years and if cracked or damaged.
7-7
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU18771
Removing and installing pan-
els
The panels shown need to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time a panel needs to
be removed and installed.
1. Panel C
To install the panel
Place the panel in the original position,
EAU40030
Panels A and B
and then install the screws and the
bolts.
To remove one of the panels
Remove the bolts and the screws, and
then pull the panel off as shown.
EAU19281
Panel C
7
1. Panel A
2. Panel B
To remove the panel
Remove the screw, and then pull the
panel off as shown.
1. Panel A
2. Screw
3. Bolt
7-8
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
Checking the spark plugsEAU19652
The spark plugs are important engine
components, which should be checked
periodically, preferably by a Yamaha
dealer. Since heat and deposits will
cause any spark plug to slowly erode,
they should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
Before installing a spark plug, the spark
plug gap should be measured with a
wire thickness gauge and, if necessary,
adjusted to specification.
1. Panel C
2. Screw
the condition of the spark plugs can re-
veal the condition of the engine.
The porcelain insulator around the cen-
ter electrode of each spark plug should
be a medium-to-light tan (the ideal color
when the vehicle is ridden normally),
To install the panel
Place the panel in the original position,
and then install the screw.
1. Spark plug gap
Spark plug gap:
and all spark plugs installed in the en-
gine should have the same color. If any
spark plug shows a distinctly different
color, the engine could be operating im-
properly. Do not attempt to diagnose
such problems yourself. Instead, have
a Yamaha dealer check the vehicle.
If a spark plug shows signs of electrode
erosion and excessive carbon or other
deposits, it should be replaced.
0.6–0.7 mm (0.024–0.028 in)
7
Clean the surface of the spark plug
gasket and its mating surface, and then
wipe off any grime from the spark plug
threads.
Tightening torque:
Spark plug:
12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)
Specified spark plug:
NGK/CR9EK
7-9
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU19876
Canister (for California onElAyU)19681 Engine oil and oil filter car-
TIP
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci-
fied torque as soon as possible.
tridge
The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter car-
tridge replaced at the intervals speci-
fied in the periodic maintenance and
lubrication chart.
ECA10840
NOTICE
To check the engine oil level
Do not use any tools to remove or in-
stall the spark plug cap, otherwise
the ignition coil coupler may get
damaged. The spark plug cap may
be difficult to remove because the
rubber seal on the end of the cap fits
tightly. To remove the spark plug
cap, simply twist it back and forth
while pulling it out; to install it, twist
it back and forth while pushing it in.
1. Place the vehicle on the center-
This model is equipped with a canister
stand. A slight tilt to the side can
to prevent the discharging of fuel vapor
result in a false reading.
into the atmosphere. Before operating
2. Start the engine, warm it up for
this vehicle, make sure to check the fol-
several minutes, and then turn it
lowing:
off.
G Check each hose connection.
G Check each hose and canister for
3. Wait a few minutes until the oil set-
7
tles, and then check the oil level
cracks or damage. Replace if dam-
through the engine oil level check
aged.
window located at the bottom-right
side of the crankcase.
G Make sure that the canister breath-
er is not blocked, and if necessary,
clean it.
TIP
The engine oil should be between the
minimum and maximum level marks.
7-10
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
4. Remove the engine oil filler cap
and drain bolt to drain the oil from
the crankcase.
1. Engine oil filler cap
2. Engine oil level check window
3. Maximum level mark
1. Oil filter wrench
2. Oil filter cartridge
4. Minimum level mark
1. Engine oil drain bolt
TIP
An oil filter wrench is available at a
Yamaha dealer.
4. If the engine oil is below the mini-
TIP
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
Skip steps 5–7 if the oil filter cartridge is
not being replaced.
6. Apply a thin coat of clean engine
oil to the O-ring of the new oil filter
cartridge.
7
5. Remove the oil filter cartridge with
an oil filter wrench.
To change the engine oil (with or
without oil filter cartridge replace-
ment)
1. Place the vehicle on a level sur-
face.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Place an oil pan under the engine
to collect the used oil.
7-11
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
Recommended engine oil:
See page 9-1.
Oil quantity:
Without oil filter cartridge replace-
ment:
2.90 L (3.07 US qt, 2.55 Imp.qt)
With oil filter cartridge replacement:
3.10 L (3.28 US qt, 2.73 Imp.qt)
TIP
1. O-ring
1. Torque wrench
Be sure to wipe off spilled oil on any
parts after the engine and exhaust sys-
tem have cooled down.
Tightening torque:
TIP
Oil filter cartridge:
Make sure that the O-ring is properly
seated.
ECA11620
17 Nm (1.7 m·kgf, 12 ft·lbf)
NOTICE
8. Install the engine oil drain bolt, and
7. Install the new oil filter cartridge
with an oil filter wrench, and then
tighten it to the specified torque
with a torque wrench.
G In order to prevent clutch slip-
then tighten it to the specified
torque.
page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci-
7
Tightening torque:
Engine oil drain bolt:
fication of “CD” or oils of a high-
er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
43 Nm (4.3 m·kgf, 31 ft·lbf)
9. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
G Make sure that no foreign mate-
rial enters the crankcase.
7-12
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU20070
11. Turn the engine off, and then
Coolant
1
check the oil level and correct it if
necessary.
The coolant level should be checked
before each ride. In addition, the cool-
ant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
2
EAU40042
To check the coolant level
1. Place the vehicle on the center-
1. “CD” specification
stand.
2. “ENERGY CONSERVING II”
TIP
10. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im-
mediately turn the engine off and
check for the cause.
G The coolant level must be checked
on a cold engine since the level
varies with engine temperature.
G Make sure that the vehicle is posi-
tioned straight up when checking
the coolant level. A slight tilt to the
side can result in an incorrect
reading.
7
TIP
After the engine is started, the engine
oil level warning light should go off if the
oil level is sufficient.
2. Check the coolant level in the cool-
ant reservoir.
ECA10400
NOTICE
TIP
If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha dealer
check the vehicle.
The coolant should be between the
minimum and maximum level marks.
7-13
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU33031
of coolant, replace it with cool-
Changing the coolant
ant as soon as possible, other-
The coolant must be changed at the in-
wise the cooling system will not
tervals specified in the periodic mainte-
be protected against frost and
nance and lubrication chart. Have a
corrosion. If water has been
Yamaha dealer change the coolant.
added to the coolant, have a
WARNING! Never attempt to remove
Yamaha dealer check the anti-
the radiator cap when the engine is
freeze content of the coolant as
hot.
[EWA10381]
soon as possible, otherwise the
effectiveness of the coolant will
1. Coolant reservoir
2. Maximum level mark
3. Minimum level mark
be reduced.
[ECA10472]
3. If the coolant is at or below the
minimum level mark, remove pan-
el C. (See page 7-8.)
4. Remove the reservoir cap, add
coolant to the maximum level
mark, and then install the reservoir
cap. WARNING! Remove only
the coolant reservoir cap. Never
attempt to remove the radiator
cap when the engine is hot.
7
1. Coolant reservoir cap
Coolant reservoir capacity (up to the
maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
[EWA15161]
NOTICE: If coolant is not
available, use distilled water or
soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
5. Install the panel.
7-14
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU40052
Replacing the air filter element
The air filter element should be re-
placed at the intervals specified in the
periodic maintenance and lubrication
chart. Replace the air filter element
more frequently if you are riding in un-
usually wet or dusty areas.
1. Remove the rider seat. (See page
4-14.)
2. Remove panels A and B. (See
1. Bolt
6. Remove the air filter case cover by
removing the screws. NOTICE:
When removing the air filter
case cover, be careful not to al-
low foreign objects to drop into
page 7-8.)
3. Remove the cowling bolts, and
5. Lift the front of the fuel tank, and
carefully tilt it back and away from
the air filter case, but do not dis-
then pull the cowling off.
connect
the
fuel
hoses.
the air intake manifold.
[ECA12881]
fuel tank is well supported. Do
not tilt or pull the fuel tank too
much, otherwise the fuel hoses
may come loose, which could
cause fuel leakage and a fire
7
hazard.
[EWA10411]
1. Cowling
2. Bolt
1. Screw
2. Air filter case cover
4. Remove the fuel tank bolts.
7. Pull the air filter element out.
7-15
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
hose and the fuel tank overflow 14. Install the rider seat.
hose in the original position.
WARNING! Before placing the
fuel tank in the original position,
make sure that the fuel hoses
are not damaged. If any fuel
hose is damaged, do not start
the engine but have a Yamaha
dealer replace the hose, other-
wise fuel may leak, creating a
1. Air filter element
2. Air intake manifold
fire hazard.
[EWA11361]
8. Insert a new air filter element into
the air filter case. NOTICE: Make
sure that the air filter element is
properly seated in the air filter
case. The engine should never
be operated without the air filter
element installed, otherwise the
piston(s) and/or cylinder(s) may
7
3
become
excessively
worn.
1. Fuel tank breather hose (except for Califor-
nia)
[ECA10481]
9. Install the air filter case cover by in-
stalling the screws.
2. Original position (paint mark)
3. Fuel tank overflow hose
10. Place the fuel tank in the original
position. Make sure that the fuel
hoses are properly connected and
routed, and not pinched. Be sure
to place the fuel tank breather
11. Install the fuel tank bolts.
12. Place the cowling in the original
position, and then install the bolts.
13. Install the panels.
7-16
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU44732
EAU21382
EAU21401
Checking the engine idling
speed
Check the engine idling speed and, if
necessary, have it adjusted by a
Yamaha dealer at the intervals speci-
fied in the periodic maintenance and lu-
brication chart.
Checking the throttle cable
free play
Valve clearance
The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
Engine idling speed:
1100–1300 r/min
1. Throttle cable free play
The throttle cable free play should mea-
sure 3.0–5.0 mm (0.12–0.20 in) at the
throttle grip. Periodically check the
throttle cable free play and, if neces-
sary, have a Yamaha dealer adjust it.
7
7-17
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU21751
Tire inspection
Tire air pressure (measured on cold
Tires
tires):
To maximize the performance, durabil-
ity, and safe operation of your motor-
cycle, note the following points
regarding the specified tires.
0–90 kg (0–198 lb):
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
FZS10Y 90–190 kg (198–419 lb)
FZS10YC 90–189 kg (198–417 lb):
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
High-speed riding:
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Maximum load*:
FZS10Y 190 kg (419 lb)
FZS10YC 189 kg (417 lb)
* Total weight of rider, passenger, car-
go and accessories
Tire air pressure
The tire air pressure should be checked
and, if necessary, adjusted before each
ride.
1. Tire sidewall
2. Tire wear indicator
3. Tire tread depth
EWA10501
WARNING
Operation of this vehicle with im-
proper tire pressure may cause se-
vere injury or death from loss of
control.
G The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
G The tire air pressure must be ad-
justed in accordance with the
riding speed and with the total
weight of rider, passenger, car-
go, and accessories approved
for this model.
Always check the tires before operating
the motorcycle. If a tire tread shows
crosswise lines (minimum tread depth),
if the tire has a nail or glass fragments
in it, or if the sidewall is cracked, con-
tact a Yamaha dealer immediately and
have the tire replaced.
7
EWA10511
WARNING
Minimum tire tread depth (front and
rear):
1.0 mm (0.04 in)
Never overload your vehicle. Opera-
tion of an overloaded vehicle could
cause an accident.
7-18
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EWA10580
This motorcycle is equipped with cast
Front tire:
Size:
WARNING
wheels and tubeless tires with valves.
EWA10481
G It is dangerous to ride with a
worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.
G The replacement of all wheel-
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.
120/70 ZR17M/C (58W)
Manufacturer/model:
DUNLOP/D221FA
WARNING
G The front and rear tires should
be of the same make and de-
sign, otherwise the handling
characteristics of the motor-
cycle may be different, which
could lead to an accident.
G Always make sure that the valve
caps are securely installed to
prevent air pressure leakage.
G Use only the tire valves and
valve cores listed below to
avoid tire deflation during a
high-speed ride.
MICHELIN/Pilot Road S
Rear tire:
Size:
190/50 ZR17M/C (73W)
Manufacturer/model:
DUNLOP/D221G
MICHELIN/Pilot Road D
FRONT and REAR:
Tire air valve:
TR412
Valve core:
#9100 (original)
Tire information
EWA10600
WARNING
7
After extensive tests, only the tires list-
ed below have been approved for this
model by Yamaha Motor Co., Ltd.
This motorcycle is fitted with super-
high-speed tires. Note the following
points in order to make the most ef-
ficient use of these tires.
G Use only the specified replace-
ment tires. Other tires may run
the danger of bursting at super
high speeds.
1. Tire air valve
G Brand-new tires can have a rela-
tively poor grip on certain road
surfaces until they have been
2. Tire air valve core
3. Tire air valve cap with seal
7-19
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU21960
EAU22081
“broken in”. Therefore, it is ad-
visable before doing any high-
speed riding to ride conserva-
tively for approximately 100 km
(60 mi) after installing a new tire.
G The tires must be warmed up
before a high-speed run.
G Always adjust the tire air pres-
sure according to the operating
conditions.
Cast wheels
Adjusting the clutch lever free
To maximize the performance, durabil-
ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.
G The wheel rims should be checked
for cracks, bends or warpage be-
fore each ride. If any damage is
found, have a Yamaha dealer re-
place the wheel. Do not attempt
even the smallest repair to the
wheel. A deformed or cracked
wheel must be replaced.
play
1. Clutch lever free play adjusting bolt
2. Clutch lever free play
G The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han-
dling characteristics, and a short-
ened tire life.
G Ride at moderate speeds after
changing a tire since the tire sur-
face must first be “broken in” for it
to develop its optimal characteris-
tics.
The clutch lever free play should mea-
sure 10.0–15.0 mm (0.39–0.59 in) as
shown. Periodically check the clutch le-
ver free play and, if necessary, adjust it
as follows.
To increase the clutch lever free play,
turn the clutch lever free play adjusting
bolt in direction (a). To decrease the
clutch lever free play, turn the adjusting
bolt in direction (b).
7
7-20
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22390
Adjusting the rear brake liEgAUh22t271 Checking the front and rear
TIP
If the specified free play cannot be ob-
tained as described above or if the
clutch does not operate correctly, have
a Yamaha dealer check the internal
clutch mechanism.
switch
brake pads
The front and rear brake pads must be
checked for wear at the intervals spec-
ified in the periodic maintenance and
lubrication chart.
EAU36890
Front brake pads
1
1. Rear brake light switch
2. Rear brake light switch adjusting nut
The rear brake light switch, which is ac-
tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the rear brake light switch adjust-
ing nut while holding the rear brake light
switch in place. To make the brake light
come on earlier, turn the adjusting nut
in direction (a). To make the brake light
come on later, turn the adjusting nut in
direction (b).
1
7
1. Brake pad wear indicator
Each front brake pad is provided with
wear indicators, which allows you to
check the brake pad wear without hav-
ing to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicators while applying
the brake. If a brake pad has worn to
7-21
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22571
the point that a wear indicator almost
touches the brake disc, have a Yamaha
dealer replace the brake pads as a set.
Before riding, check that the brake fluid
is above the minimum level mark and
Checking the brake fluid level
replenish if necessary. A low brake fluid
level may indicate worn brake pads
and/or brake system leakage. If the
brake fluid level is low, be sure to check
the brake pads for wear and the brake
system for leakage.
Front brake
EAU22500
Rear brake pads
TIP
The rear brake fluid reservoir is located
behind panel C. (See page 7-8.)
Observe these precautions:
G When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.
1. Minimum level mark
Rear brake
1. Lining thickness
G Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.
Check each rear brake pad for damage
and measure the lining thickness. If a
brake pad is damaged or if the lining
thickness is less than 1.0 mm (0.04 in),
have a Yamaha dealer replace the
brake pads as a set.
7
Recommended brake fluid:
DOT 4
1. Minimum level mark
G Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.
Insufficient brake fluid may allow air to
enter the brake system, possibly caus-
ing it to become ineffective.
7-22
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU22731
EAU22760
G Be careful that water does not en-
Changing the brake fluid
Drive chain slack
ter the brake fluid reservoir when
Have a Yamaha dealer change the The drive chain slack should be
brake fluid at the intervals specified in checked before each ride and adjusted
the TIP after the periodic maintenance if necessary.
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.
G Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.
G As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.
and lubrication chart. In addition, have
EAU22793
the oil seals of the master cylinders and
To check the drive chain slack
calipers as well as the brake hoses re-
1. Place the motorcycle on the cen-
placed at the intervals listed below or
terstand.
whenever they are damaged or leak-
2. Shift the transmission into the neu-
ing.
tral position.
G Oil seals: Replace every two
3. Spin the rear wheel several times
years.
to locate the tightest portion of the
G Brake hoses: Replace every four
drive chain.
years.
4. Measure the drive chain slack as
shown.
7
1. Drive chain slack
7-23
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23023
Drive chain slack:
TIP
Cleaning and lubricating the
drive chain
The drive chain must be cleaned and
20.0–30.0 mm (0.79–1.18 in)
Using the alignment marks on each
side of the swingarm, make sure that
5. If the drive chain slack is incorrect,
adjust it as follows.
both chain pullers are in the same posi-
lubricated at the intervals specified in
tion for proper wheel alignment.
the periodic maintenance and lubrica-
To adjust the drive chain slack EAU34313
1. Loosen the axle nut and the lock-
nut on each side of the swingarm.
2. To tighten the drive chain, turn the
drive chain slack adjusting bolt on
each side of the swingarm in direc-
tion (a). To loosen the drive chain,
turn the adjusting bolt on each side
of the swingarm in direction (b),
and then push the rear wheel for-
ward. NOTICE: Improper drive
chain slack will overload the en-
gine as well as other vital parts
of the motorcycle and can lead
to chain slippage or breakage.
To prevent this from occurring,
keep the drive chain slack with-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.
ECA10581
NOTICE
The drive chain must be lubricated
after washing the motorcycle and
riding in the rain.
1. Clean the drive chain with kero-
sene and a small soft brush.
NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
1. Axle nut
2. Locknut
3. Drive chain slack adjusting bolt
4. Alignment marks
7
3. Tighten the locknuts, then the axle
nut to their specified torques.
propriate solvents.
[ECA11121]
2. Wipe the drive chain dry.
Tightening torques:
Locknut:
16 Nm (1.6 m·kgf, 11 ft·lbf)
Axle nut:
3. Thoroughly lubricate the drive
chain with a special O-ring chain
lubricant. NOTICE: Do not use
engine oil or any other lubri-
cants for the drive chain, as they
in the specified limits.
[ECA10571]
150 Nm (15.0 m·kgf, 110 ft·lbf)
7-24
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23093
EAU23111
may contain substances that
could damage the O-rings.
Checking and lubricating the
Checking and lubricating the
throttle grip and cable
cables
[ECA11111]
The operation of all control cables and The operation of the throttle grip should
the condition of the cables should be be checked before each ride. In addi-
checked before each ride, and the ca- tion, the cable should be lubricated at
bles and cable ends should be lubricat- the intervals specified in the periodic
ed if necessary. If a cable is damaged maintenance chart.
or does not move smoothly, have a
Yamaha dealer check or replace it.
WARNING! Damage to the outer
housing of cables may result in in-
ternal rusting and cause interfer-
ence with cable movement. Replace
damaged cables as soon as possi-
ble to prevent unsafe conditions.
[EWA10711]
7
Recommended lubricant:
Yamaha Chain and Cable Lube or
engine oil
7-25
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU44271
EAU23142
Recommended lubricant:
Lithium-soap-based grease
Checking and lubricating the
brake and shift pedals
Checking and lubricating the
brake and clutch levers
Brake lever
Clutch lever
7
The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu-
bricated if necessary.
The operation of the brake and clutch
levers should be checked before each
ride, and the lever pivots should be lu-
bricated if necessary.
7-26
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23213
Recommended lubricants:
Recommended lubricant:
Lithium-soap-based grease
Checking and lubricating the
centerstand and sidestand
Brake lever:
Silicone grease
Clutch lever:
Lithium-soap-based grease
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-to-
metal contact surfaces should be lubri-
cated if necessary.
7
EWA10741
WARNING
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or re-
pair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
7-27
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23272
EAU45511
Checking the front fork
Checking the steering
The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
1. Place the vehicle on the center-
stand. WARNING! To avoid inju-
ECA10590
ry, securely support the vehicle
NOTICE
To check the operation
so there is no danger of it falling
over.
1. Place the vehicle on a level sur-
face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
[EWA10751]
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-
pair it.
2. Hold the lower ends of the front
fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
over.
[EWA10751]
7
2. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
7-28
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23290
EAU33653
working near batteries. In case
of contact, administer the fol-
lowing FIRST AID.
• EXTERNAL: Flush with plenty
of water.
• INTERNAL: Drink large quan-
tities of water or milk and im-
mediately call a physician.
• EYES: Flush with water for 15
minutes and seek prompt
medical attention.
Checking the wheel bearings
Battery
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.
1. Positive battery lead (red)
2. Negative battery lead (black)
3. Battery
G Batteries produce explosive hy-
drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro-
vide sufficient ventilation when
charging it in an enclosed
space.
G KEEP THIS AND ALL BATTER-
IES OUT OF THE REACH OF
CHILDREN.
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electro-
lyte or to add distilled water. However,
the battery lead connections need to be
7
checked and, if necessary, tightened.
EWA10760
WARNING
G Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
To charge the battery
Have a Yamaha dealer charge the bat-
tery as soon as possible if it seems to
have discharged. Keep in mind that the
7-29
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU43011
battery tends to discharge more quickly
if the vehicle is equipped with optional
2. If the battery will be stored for more
Replacing the fuses
than two months, check it at least
The main fuse, the fuel injection system
once a month and fully charge it if
electrical accessories.
fuse, and the fuse box, which contains
necessary.
ECA16520
the fuses for the individual circuits, are
3. Fully charge the battery before in-
NOTICE
located under the rider seat. (See page
stallation.
4. After installation, make sure that
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (con-
stant-voltage) battery charger is re-
quired. Using a conventional battery
charger will damage the battery. If
you do not have access to a con-
4-14.)
the battery leads are properly con-
nected to the battery terminals.
ECA16530
NOTICE
stant-voltage battery charger, have a Always keep the battery charged.
Yamaha dealer charge your battery. Storing a discharged battery can
cause permanent battery damage.
To store the battery
1. If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then discon-
nect the negative lead before
disconnecting the positive lead.
[ECA16302]
1. Main fuse
2. Fuse box
3. Fuel injection system fuse
4. Fuel injection system spare fuse
7
7-30
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
avoid causing extensive dam-
age to the electrical system and
possibly a fire.
[EWA15131]
Specified fuses:
Main fuse:
50.0 A
Headlight fuse:
20.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
15.0 A
Fuel injection system fuse:
15.0 A
Radiator fan fuse:
10.0 A × 2
Backup fuse:
10.0 A
1. Fuse box
2. Headlight fuse
3. Ignition fuse
4. Signaling system fuse
5. Backup fuse (for odometer and clock)
6. Right radiator fan fuse
7. Left radiator fan fuse
8. Spare fuse
1. Battery band
2. Battery cover
7
If a fuse is blown, replace it as follows.
4. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
5. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
6. Install the battery cover, and then
hook the battery band onto the
holder.
TIP
Include steps 2 and 6 only for the fuel
injection system fuse.
1. Fuel injection system fuse
2. Fuel injection system spare fuse
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Unhook the battery band, and then
remove the battery cover.
3. Remove the blown fuse, and then
install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
7-31
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU23932
Replacing a headlight bulb
This model is equipped with quartz bulb
headlights. If a headlight bulb burns
out, replace it as follows.
ECA10650
NOTICE
Take care not to damage the follow-
ing parts:
G Headlight bulb
1. Do not touch the glass part of the bulb.
1. Headlight bulb holder
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.
1. Disconnect the headlight coupler,
and then remove the bulb cover.
3. Place a new headlight bulb into po-
sition, and then secure it with the
bulb holder.
4. Install the headlight bulb cover,
and then connect the coupler.
5. Have a Yamaha dealer adjust the
headlight beam if necessary.
7
G Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of a
wattage higher than specified.
1. Headlight coupler
2. Headlight bulb cover
2. Unhook the headlight bulb holder,
and then remove the burnt-out
bulb.
7-32
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24114
EAU43002
Replacing the tail/brake light
Replacing a turn signal light
bulb
bulb
1. Remove the passenger seat. (See
page 4-14.)
1. Remove the turn signal light unit
by removing the screw.
the bulb) by turning it counter-
clockwise.
1. Turn signal light bulb socket
3. Remove the burnt-out bulb by pull-
ing it out.
1. Turn signal light unit
2. Screw
2. Remove the socket (together with
the bulb) by turning it counter-
clockwise.
7
1. Tail/brake light bulb socket
3. Remove the burnt-out bulb by
pushing it in and turning it counter-
clockwise.
4. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
5. Install the socket (together with the
bulb) by turning it clockwise.
6. Install the passenger seat.
1. Turn signal light bulb
4. Insert a new bulb into the socket.
5. Install the socket (together with the
bulb) by turning it clockwise.
7-33
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24312
6. Install the turn signal light unit by
installing the screw. NOTICE: Do
not overtighten the screw, oth-
erwise the lens may break.
[ECA11191]
3. Remove the burnt-out bulb by pull-
Replacing the license plate
ing it out.
light bulb
4. Insert a new bulb into the socket.
5. Install the socket (together with the
bulb) by pushing it in.
1. Remove the license plate light unit
by removing the screws.
6. Install the license plate light unit by
installing the screws.
1. License plate light unit
2. Screw
2. Remove the socket (together with
the bulb) by pulling it out.
7
1. License plate light bulb
7-34
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU24360
EAU40210
3. Remove the brake hose holder on
To install the front wheel
Front wheel
each side by removing the bolt and
nut.
1. Lift the wheel up between the fork
EAU40201
legs.
4. Remove the brake caliper (togeth-
er with the reflector) on each side
by removing the bolts. NOTICE:
Do not apply the brake after the
brake calipers have been re-
moved, otherwise the brake
To remove the front wheel
WARNING
2. Insert the wheel axle.
3. Install the brake caliper (together
with the reflector) on each side by
installing the bolts.
EWA10821
To avoid injury, securely support the
vehicle so there is no danger of it
falling over.
TIP
pads will be forced shut.
[ECA11051]
Make sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.
1. Place the vehicle on the center-
stand.
2. Loosen the front wheel axle pinch
bolt, then the wheel axle and the
brake caliper bolts.
4. Install the brake hose holder on
each side by installing the bolt and
nut.
5. Take the vehicle off the center-
stand so that the front wheel is on
the ground.
6. Tighten the wheel axle, the front
wheel axle pinch bolt, and the
brake caliper bolts to the specified
torques.
7
1. Brake hose holder
2. Bolt and nut
3. Brake caliper bolt
4. Brake caliper
5. Reflector
1. Front wheel axle pinch bolt
2. Wheel axle
5. Pull the wheel axle out, and then
remove the wheel.
7-35
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU25080
4. Loosen the locknut on each side of
Tightening torques:
Wheel axle:
72 Nm (7.2 m·kgf, 52 ft·lbf)
Front wheel axle pinch bolt:
23 Nm (2.3 m·kgf, 17 ft·lbf)
Brake caliper bolt:
Rear wheel
the swingarm.
5. Turn the drive chain slack adjust-
ing bolts fully in direction (a) and
push the wheel forward.
6. Remove the drive chain from the
rear sprocket.
EAU40021
To remove the rear wheel
WARNING
EWA10821
40 Nm (4.0 m·kgf, 29 ft·lbf)
To avoid injury, securely support the
vehicle so there is no danger of it
falling over.
7. Push down hard on the handlebar
several times to check for proper
fork operation.
TIP
G If the drive chain is difficult to re-
move, remove the wheel axle first,
and then lift the wheel upward
enough to remove the drive chain
from the rear sprocket.
1. Loosen the axle nut.
G The drive chain cannot be disas-
sembled.
7. While supporting the brake caliper
bracket, pull the wheel axle out,
and then remove the wheel.
NOTICE: Do not apply the brake
after the wheel has been re-
moved together with the brake
disc, otherwise the brake pads
7
1. Axle nut
2. Locknut
3. Drive chain slack adjusting bolt
4. Brake caliper
5. Brake caliper bracket
will be forced shut.
[ECA11071]
2. Place the vehicle on the center-
stand.
3. Remove the axle nut.
7-36
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU25871
Troubleshooting
Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur-
ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems your-
self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace-
ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi-
or, have a shorter service life and can
1. Wheel axle
1. Slot
2. Retainer
EAU39411
2. Install the drive chain onto the rear
sprocket.
3. Install the axle nut, and then lower
the rear wheel so that it is on the
ground.
4. Adjust the drive chain slack. (See
page 7-23.)
5. Tighten the axle nut to the speci-
fied torque.
To install the rear wheel
1. Install the wheel and the brake cal-
iper bracket by inserting the wheel
axle from the left-hand side.
TIP
7
G Make sure that the slot in the brake
caliper bracket is fit over the retain-
er on the swingarm.
G Make sure that there is enough
space between the brake pads be-
fore installing the wheel.
Tightening torque:
Axle nut:
lead to expensive repair bills.
EWA15141
150 Nm (15.0 m·kgf, 110 ft·lbf)
WARNING
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the ar-
ea, including pilot lights from water
7-37
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
heaters or furnaces. Gasoline or
gasoline vapors can ignite or ex-
plode, causing severe injury or
property damage.
7
7-38
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
EAU42501
Troubleshooting charts
Starting problems or poor engine performance
1. Fuel
There is enough fuel.
Check the compression.
Check the fuel level in
the fuel tank.
The engine does not start.
Check the compression.
There is no fuel.
Supply fuel.
2. Compression
There is compression.
Check the ignition.
Operate the electric starter.
Have a Yamaha dealer
check the vehicle.
There is no compression.
3. Ignition
Wipe off with a dry cloth and correct the
spark plug gaps, or replace the spark plugs.
Operate the electric starter.
Wet
Dry
Remove the spark plugs
and check the electrodes.
7
The engine does not start.
Check the battery.
Have a Yamaha dealer check the vehicle.
4. Battery
The engine turns over
quickly.
The battery is good.
The engine does not start.
Operate the electric starter.
Have a Yamaha dealer
check the vehicle.
The engine turns over
slowly.
Check the battery lead connections,
and charge the battery if necessary.
7-39
Download from Www.Somanuals.com. All Manuals Search And Download.
PERIODIC MAINTENANCE AND ADJUSTMENT
Engine overheating
WARNING
EWAT1040
G Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
G Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the de-
tent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap
while turning it counterclockwise, and then remove the cap.
There is
leakage.
Have a Yamaha dealer check
and repair the cooling system.
The coolant level is low.
Check the cooling system
for leakage.
There is
no leakage.
Add coolant. (See TIP.)
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
The coolant level
is OK.
7
TIP
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant
as soon as possible.
7-40
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTORCYCLE CARE AND STORAGE
EAU37833
EAU26013
ucts onto seals, gaskets, sprock-
ets, the drive chain and wheel
axles. Always rinse the dirt and de-
greaser off with water.
Matte color caution
Care
ECA15192
While the open design of a motorcycle
reveals the attractiveness of the tech-
nology, it also makes it more vulnera-
ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un-
noticed on a car, however, it detracts
from the overall appearance of a motor-
cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.
NOTICE
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be-
fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin-
ished parts.
Cleaning
NOTICE
ECA10771
G Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af-
fected area any longer than in-
structed. Also, thoroughly rinse
the area off with water, immedi-
ately dry it, and then apply a cor-
rosion protection spray.
G Improper cleaning can damage
plastic parts such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug caps, are tightly in-
stalled.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-
8
G Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
8-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTORCYCLE CARE AND STORAGE
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust re-
movers or inhibitors, brake flu-
id, antifreeze or electrolyte.
scratched, use a quality plastic
1. Clean the motorcycle with cold wa-
ter and a mild detergent, after the
polishing
washing.
compound
after
engine
has
cooled
down.
NOTICE: Do not use warm water
since it increases the corrosive
After normal use
G Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and swing-
arm bearings, fork and brakes),
electric components (couplers,
action of the salt.
[ECA10791]
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the motorcycle with a chamois
connectors,
instruments,
switches and lights), breather
hoses and vents.
or an absorbing cloth.
2. Immediately dry the drive chain
and lubricate it to prevent it from
rusting.
3. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-
steel exhaust systems can be re-
moved through polishing.)
4. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal,
including chrome- and nickel-plat-
ed, surfaces.
After riding in the rain, near the sea or
on salt-sprayed roads
G For motorcycles equipped with
a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com-
pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid-
den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
Since sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.
8
TIP
Salt sprayed on roads in the winter may
remain well into spring.
8-2
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTORCYCLE CARE AND STORAGE
EAU26181
5. Use spray oil as a universal clean-
er to remove any remaining dirt.
6. Touch up minor paint damage
caused by stones, etc.
7. Wax all painted surfaces.
8. Let the motorcycle dry completely
G Never apply oil or wax to any
Storage
rubber and plastic parts, but
treat them with a suitable care
product.
Short-term
Always store your motorcycle in a cool,
dry place and, if necessary, protect it
G Avoid using abrasive polishing
compounds as they will wear
away the paint.
against dust with a porous cover.
before storing or covering it.
ECA10810
EWA11131
NOTICE
WARNING
TIP
G Storing the motorcycle in a
poorly ventilated room or cover-
ing it with a tarp, while it is still
wet, will allow water and humid-
ity to seep in and cause rust.
G To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi-
cals are stored.
Consult a Yamaha dealer for advice on
what products to use.
Contaminants on the brakes or tires
can cause loss of control.
G Make sure that there is no oil or
wax on the brakes or tires.
G If necessary, clean the brake
discs and brake linings with a
regular brake disc cleaner or ac-
etone, and wash the tires with
warm water and a mild deter-
gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-
nering behavior.
8
Long-term
Before storing your motorcycle for sev-
eral months:
ECA10800
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
NOTICE
G Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
8-3
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTORCYCLE CARE AND STORAGE
3. Perform the following steps to pro-
tect the cylinders, piston rings, etc.
from corrosion.
4. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.
a. Remove the spark plug caps
and spark plugs.
b. Pour a teaspoonful of engine oil
into each spark plug bore.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
c. Install the spark plug caps onto
the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder walls with oil.)
WARNING! To prevent dam-
age or injury from sparking,
make sure to ground the
spark plug electrodes while
turning the engine over.
[EWA10951]
6. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
7-29.
8
e. Remove the spark plug caps
from the spark plugs, and then
install the spark plugs and the
spark plug caps.
TIP
Make any necessary repairs before
storing the motorcycle.
8-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Dimensions:
Overall length:
Engine oil:
Type:
Fuel:
Recommended fuel:
2140 mm (84.3 in)
Overall width:
770 mm (30.3 in)
Overall height:
1205 mm (47.4 in)
Seat height:
815 mm (32.1 in)
Wheelbase:
YAMALUBE 4 10W-40 or 20W-50, SAE
10W-40 or SAE 20W-50
Unleaded gasoline only
Fuel tank capacity:
18.0 L (4.76 US gal, 3.96 Imp.gal)
Fuel reserve amount:
3.4 L (0.90 US gal, 0.75 Imp.gal)
Fuel injection:
0
10 30 50 70 90 110 130 ˚F
YAMALUBE 4 10W-40
or SAE 10W-40
Throttle body:
Manufacturer:
1460 mm (57.5 in)
Ground clearance:
135 mm (5.31 in)
Minimum turning radius:
3000 mm (118.1 in)
Weight:
With oil and fuel:
FZS10Y 220.0 kg (485 lb)
FZS10YC 221.0 kg (487 lb)
Engine:
YAMALUBE 4 20W-50
MIKUNI
Type/quantity:
FZS10Y SE 45EIDW-B41/1
FZS10YC SE 45EIDW-B44/1
Spark plug (s):
Manufacturer/model:
NGK/CR9EK
Spark plug gap:
0.6–0.7 mm (0.024–0.028 in)
Clutch:
Clutch type:
Wet, multiple-disc
Transmission:
Primary reduction system:
Spur gear
Primary reduction ratio:
65/43 (1.512)
Secondary reduction system:
Chain drive
or SAE 20W-50
–20 –10
0
10 20 30 40
50 ˚C
Recommended engine oil grade:
API service SG type or higher, JASO
standard MA
Engine oil quantity:
Without oil filter cartridge replacement:
2.90 L (3.07 US qt, 2.55 Imp.qt)
With oil filter cartridge replacement:
3.10 L (3.28 US qt, 2.73 Imp.qt)
Cooling system:
Coolant reservoir capacity (up to the
maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator capacity (including all routes):
2.25 L (2.38 US qt, 1.98 Imp.qt)
Air filter:
Engine type:
Liquid cooled 4-stroke, DOHC
Cylinder arrangement:
Forward-inclined parallel 4-cylinder
Displacement:
998.0 cm³
Bore × stroke:
77.0 × 53.6 mm (3.03 × 2.11 in)
Compression ratio:
11.50 :1
Starting system:
Electric starter
9
Secondary reduction ratio:
45/17 (2.647)
Transmission type:
Constant mesh 6-speed
Air filter element:
Oil-coated paper element
Lubrication system:
Wet sump
9-1
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Operation:
Left foot operation
Size:
190/50 ZR17M/C (73W)
Front wheel:
Wheel type:
Gear ratio:
1st:
Manufacturer/model:
DUNLOP/D221G
Cast wheel
Rim size:
38/15 (2.533)
2nd:
33/16 (2.063)
3rd:
37/21 (1.762)
4th:
35/23 (1.522)
5th:
27/20 (1.350)
6th:
29/24 (1.208)
Manufacturer/model:
MICHELIN/Pilot Road D
Loading:
17M/C x MT3.50
Rear wheel:
Wheel type:
Cast wheel
Rim size:
17M/C x MT6.00
Front brake:
Type:
Dual disc brake
Operation:
Right hand operation
Recommended fluid:
DOT 4
Maximum load:
FZS10Y 190 kg (419 lb)
FZS10YC 189 kg (417 lb)
(Total weightof rider, passenger, cargo and
accessories)
Tire air pressure (measured on cold
tires):
Loading condition:
Chassis:
Frame type:
0–90 kg (0–198 lb)
Front:
Diamond
Caster angle:
25.00 °
Trail:
109.0 mm (4.29 in)
Front tire:
Type:
Tubeless
Size:
120/70 ZR17M/C (58W)
Manufacturer/model:
DUNLOP/D221FA
Manufacturer/model:
MICHELIN/Pilot Road S
Rear tire:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Loading condition:
FZS10Y 90–190 kg (198–419 lb)
FZS10YC 90–189 kg (198–417 lb)
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
High-speed riding:
Front:
250 kPa (2.50 kgf/cm², 36 psi)
Rear:
290 kPa (2.90 kgf/cm², 42 psi)
Rear brake:
Type:
Single disc brake
Operation:
Right foot operation
Recommended fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
130.0 mm (5.12 in)
Rear suspension:
Type:
9
Type:
Tubeless
Swingarm (link suspension)
9-2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Spring/shock absorber type:
Coil spring/gas-oil damper
Wheel travel:
Oil level warning light:
LED
Turn signal indicator light:
130.0 mm (5.12 in)
Electrical system:
Ignition system:
TCI (digital)
Charging system:
AC magneto
LED
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
Fuses:
Main fuse:
50.0 A
Battery:
Model:
Headlight fuse:
20.0 A
Signaling system fuse:
10.0 A
Ignition fuse:
15.0 A
Radiator fan fuse:
10.0 A × 2
Fuel injection system fuse:
15.0 A
Backup fuse:
10.0 A
YTZ14S
Voltage, capacity:
12 V, 11.2 Ah
Headlight:
Bulb type:
Halogen bulb
Bulb voltage, wattage × quantity:
Headlight:
12 V, 60 W/55.0 W × 2
Tail/brake light:
12 V, 5.0 W/21.0 W × 1
Front turn signal/position light:
12 V, 21 W/5.0 W × 2
Rear turn signal light:
12 V, 21.0 W × 2
License plate light:
12 V, 5.0 W × 1
Meter lighting:
9
LED
Neutral indicator light:
LED
High beam indicator light:
LED
9-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26351
EAU26381
EAU26400
Key identification number
Vehicle identification number
Identification numbers
Record the key identification number,
vehicle identification number and mod-
el label information in the spaces pro-
vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi-
cle is stolen.
KEY IDENTIFICATION NUMBER:
1. Key identification number
1. Vehicle identification number
The key identification number is The vehicle identification number is
stamped into the key tag. Record this stamped into the steering head pipe.
number in the space provided and use Record this number in the space pro-
it for reference when ordering a new vided.
VEHICLE IDENTIFICATION
NUMBER:
key.
TIP
The vehicle identification number is
used to identify your motorcycle and
may be used to register your motor-
cycle with the licensing authority in your
area.
MODEL LABEL INFORMATION:
10
10-1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26470
Model label
1. Model label
The model label is affixed to the frame
under the rider seat. (See page 4-14.)
Record the information on this label in
the space provided. This information
will be needed when ordering spare
parts from a Yamaha dealer.
10
10-2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26551
Reporting safety defects
If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately
inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group
of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to
http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also
obtain other information about motor vehicle safety from http://www.safercar.gov.
10
10-3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26560
Motorcycle noise regulation
TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:
Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve-
hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.
Exhaust system
• Muffler
• Exhaust pipe
• Silencer
Intake system
• Air cleaner case
• Air cleaner element
• Intake duct
10
10-4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26632
Maintenance record
Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that
maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder
that maintenance work is required. It is not acceptable proof of maintenance work.
Maintenance
interval
Date of
service
Servicing dealer
name and address
Mileage
Remarks
600 mi
(1000 km) or
1 month
4000 mi
(7000 km) or
6 months
8000 mi
(13000 km) or
12 months
12000 mi
(19000 km) or
18 months
16000 mi
(25000 km) or
24 months
20000 mi
(31000 km) or
30 months
24000 mi
(37000 km) or
36 months
28000 mi
(43000 km) or
42 months
10
32000 mi
(49000 km) or
48 months
10-5
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
Maintenance
interval
Date of
service
Servicing dealer
name and address
Mileage
Remarks
36000 mi
(55000 km) or
54 months
40000 mi
(61000 km) or
60 months
10
10-6
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26663
YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED
WARRANTY
Yamaha Motor Corporation, U.S.A. hereby warrants that
new Yamaha motorcycles will be free from defects in
material and workmanship for the period of time stated
herein, subject to certain stated limitations.
THE CUSTOMER’S RESPONSIBILITY under this
warranty shall be to:
1. Operate and maintain the motorcycle as specified in
the appropriate Owner’s Manual, and
2. Give notice to an authorized Yamaha motorcycle
dealer of any and all apparent defects within ten (10)
days after discovery, and make the machine available
at that time for inspection and repairs at such dealer’s
place of business.
Engine
Displacement
Under 50cc
Period
6,000 km (3,750 miles)
or five years, whichever occurs first
THE PERIOD OF WARRANTY for Yamaha motorcycles
originally equipped with headlight, stoplight, and turn
signals shall be one (1) year from the date of purchase,
with no mileage limitation.
50cc to 169cc
170cc to 279cc
280cc and over
12,000 km (7,465 miles)
or five years whichever occurs first
18,000 km (11,185 miles)
or five years, whichever occurs first
MODELS EXCLUDED FROM WARRANTY include
those used for non-Yamaha-authorized renting, leasing
or other commercial purposes, and TZ models.
WARRANTY TRANSFER: To transfer the warranty from
the original purchaser to any subsequent purchaser, it is
imperative that the machine be inspected and registered
for warranty by an authorized Yamaha motorcycle dealer.
In order for this warranty to remain in effect, this
inspection and registration must take place within ten
(10) days after transfer. An inspection and registration fee
will be charged for this service.
30,000 km (18,641 miles)
or five years, whichever occurs first
DURING THE PERIOD OF WARRANTY, any authorized
Yamaha motorcycle dealer will, free of charge, repair or
replace any part adjudged defective by Yamaha due to
faulty workmanship or material from the factory. Parts used
in warranty repairs will be warranted for the balance of the
product’s warranty period. All parts replaced under
warranty become property of Yamaha Motor Corporation,
U.S.A.
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO
OTHER WARRANTY OF ANY KIND, EXPRESSED OR
IMPLIED.
MERCHANTABILITY
PARTICULAR PURPOSE WHICH EXCEED THE
OBLIGATIONS AND TIME LIMITS STATED IN THIS
WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA
MOTOR CORPORATION, U.S.A. AND EXCLUDED
FROM THIS WARRANTY.
ALL
IMPLIED
AND
WARRANTIES
FITNESS FOR
OF
A
EMISSION CONTROL SYSTEM WARRANTY:
Yamaha Motor Corporation, U.S.A. also warrants to the
ultimate purchaser and each subsequent purchaser of
each Yamaha motorcycle covered by this warranty with a
displacement of 50cc or greater, that the vehicle is
designed, built, and equipped so as to conform at the
time of sale with all U.S. emissions standards applicable
at the time of manufacture and that it is free from defects
in materials and workmanship which would cause it not
to meet these standards within the period listed
immediately below. Failures other than those resulting
from defects in material or workmanship, which arise
solely as a result of owner abuse and/or lack of proper
maintenance, are not covered by this warranty.
GENERAL EXCLUSIONS from this warranty shall
include any failures caused by:
a) Competition or racing use.
b) Installation of parts or accessories that are not
qualitatively equivalent to genuine Yamaha parts.
c) Abnormal strain, neglect, or abuse.
d) Lack of proper maintenance.
SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO
EXCLUDED FROM THIS WARRANTY ARE ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING LOSS OF USE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE EXCLUSION MAY NOT APPLY TOYOU.
e) Accident or collision damage.
f) Modification to original parts.
SPECIFIC EXCLUSIONS from this warranty shall
include parts replaced due to normal wear or routine
maintenance.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
10
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Cypress, California 90630
10-7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
WARRANTY QUESTIONS AND ANSWERS
CUSTOMER SERVICE
Q.
A.
What costs are my responsibility during the warranty period?
The customer’s responsibility includes all costs of normal maintenance services,
non-warranty repairs, accident and collision damages, and oil, oil filters, air filters,
spark plugs, and brake shoes.
If your machine requires warranty service, you must take it to any authorized Yamaha
motorcycle dealer within the continental United States. Be sure to bring your warranty
registration card or other valid proof of the original date of purchase. If a question or
problem arises regarding the warranty, first contact the owner of the dealership. Since
all warranty matters are handled at the dealer level, this person is in the best position to
help you. IF you are still not satisfied and require additional assistance, please write to:
Q.
A.
What are some examples of “abnormal” strain, neglect, or abuse?
These terms are general and overlap each other in areas. Specific examples
include: Running the machine out of oil, sustained high rpm, full-throttle, operating
the machine with a broken or damaged part which causes another part to fail,
damage or failure due to improper or careless transportation and/or tie-down. If
you have any specific questions on operation or maintenance, please contact your
dealer for advice.
YAMAHA MOTOR CORPORATION, U.S.A.
CUSTOMER RELATIONS DEPARTMENT
P.O. Box 6555
Cypress, California 90630
When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any
important information such as names, addresses, model, V.I.N. (frame number),
dates, and receipts.
Q.
A.
Q.
A.
Does the warranty cover incidental costs such as towing or transportation due to
a failure?
No. The warranty is limited to repair of the machine itself.
CHANGE OF ADDRESS
May I perform any or all of the recommended maintenance shown in the Owner’s
Manual instead of having the dealer do them?
Yes, if you are a qualified mechanic and follow the procedures specified in the
Owner’s and Service Manual. We do recommend, however, that items requiring
special tools or equipment be done by a Yamaha motorcycle dealer.
The federal government requires each manufacturer of a motor vehicle to maintain a
complete, up-to-date list of all first purchasers against the possibility of a safety-
related defect and recall. This list is compiled from the purchase registrations sent to
Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.
Q.
A.
Will the warranty be void or cancelled if I do not operate or maintain my new
motorcycle exactly as specified in the Owner’s Manual?
No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” However,
if a particular failure is caused by operation or maintenance other than as
described in the Owner’s Manual, that failure may not be covered under
warranty.
If you should move after you have purchased your new motorcycle, please advise us
of your new address by sending a postcard listing your motorcycle model name, V.I.N.
(frame number), dealer number (or dealer’s name) as it is shown on your warranty
card, your name and new mailing address. Mail to:
YAMAHA MOTOR CORPORATION, U.S.A.
P.O. Box 6555
Q.
A.
What responsibility does my dealer have under this warranty?
Each Yamaha motorcycle dealer is expected to:
Cypress, California 90630
Attention: Warranty Department
1.
2.
Completely set up every new machine before sale.
Explain the operation, maintenance, and warranty requirements to your
satisfaction at the time of sale, and upon your request at any later date.
Each Yamaha motorcycle dealer is held responsible for his setup, service and
warranty repair work.
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration
record in accordance with federal law.
3.
10
Q.
A.
Is the warranty transferable to second owners?
Yes. The remainder of the existing warranty can be transferred upon request. The
unit has to be inspected and re-registered by an authorized Yamaha motorcycle
dealer for the policy to remain effective.
10-8
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
EAU26750
YAMAHA EXTENDED SERVICE (Y.E.S.)
Keep your Yamaha protected even after your warranty
expires with genuine Yamaha Extended Service (Y.E.S.).
In addition, Travel and Recreation Interruption Protection
(TRIP) is included at no extra cost. TRIP gives you up to
$150 reimbursement per occurrence for any reasonable
expenses you incur because your Yamaha needs
covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are
away from home. This superb coverage goes into effect
when you purchase Y.E.S., so it applies to any warranty
repairs as well as covered repairs during your entire
Y.E.S. plan period.
Y.E.S. is designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You
get uninterrupted factory-backed coverage for extra
peace of mind.
Y.E.S. is flexible. You choose the plan that’s right for
you: 12 months, 24 months, 36 months or, on certain
models, even 48 months beyond your warranty period.
Y.E.S. coverage is honored at any authorized Yamaha
dealer nationwide.
Y.E.S. is designed and administered by the same
Yamaha people who handle your warranty – and it
shows in the comprehensive coverage benefits. There
are no mileage limitations. Coverage isn’t limited to
“moving parts” or the “drive train” like many other plans.
And Y.E.S. covers manufacturing defects just like the
warranty. See the sample contract at your Yamaha
dealer to see how comforting uninterrupted factory-
backed protection can be.
Y.E.S. coverage is transferable to a new owner if you
sell or trade-in. That can make your Yamaha much more
valuable!
This excellent Y.E.S. plan coverage is only available to
Yamaha owners like you, and only while your Yamaha is still
within the Yamaha Limited Warranty period. So visit your
authorized Yamaha dealer to get all the facts. He can show
you how easy it is to protect your investment with Yamaha
Extended Service.
You don’t have to pay anything for covered repairs.
There’s no deductible to pay, and repairs aren’t
“pro-rated.” You don’t have any “out-of-pocket” expenses
for covered repairs.
10
10-9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSUMER INFORMATION
We urge you to act now. You’ll get the excellent benefits of
TRIP coverage right away, and you’ll rest easy knowing
you’ll have strong factory-backed protection even after your
Yamaha Limited Warranty expires.
A special note:
If visiting your dealer isn’t convenient, contact Yamaha with
your Primary ID number (your frame number). We’ll be
happy to help you get the Y.E.S. coverage you need.
Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD (1-866-937-3983)
10
10-10
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
A
F
O
Air filter element, replacing................... 7-15
Front and rear brake pads, checking ....7-21
Front fork, adjusting ..............................4-16
Front fork, checking...............................7-28
Fuel .......................................................4-12
Fuel tank cap.........................................4-12
Fuses, replacing....................................7-30
Oil level warning light.............................. 4-2
B
P
Battery .................................................. 7-29
Panels, removing and installing.............. 7-8
Parking.................................................... 6-4
Part locations.......................................... 3-1
Pre-operation check list .......................... 5-2
Brake and clutch levers, checking
and lubricating.................................... 7-26
Brake and shift pedals, checking
H
and lubricating.................................... 7-26
Brake fluid, changing............................ 7-23
Brake fluid level, checking.................... 7-22
Brake lever ........................................... 4-11
Brake pedal .......................................... 4-11
R
Handlebar switches.................................4-9
Rear brake light switch, adjusting......... 7-21
Hazard switch........................................4-10
Headlight bulb, replacing.......................7-32
High beam indicator light.........................4-2
Horn switch ...........................................4-10
S
Safety defects, reporting....................... 10-3
Safety information................................... 2-1
Shifting.................................................... 6-2
Shift pedal............................................. 4-11
Shock absorber assembly, adjusting.... 4-18
Sidestand.............................................. 4-21
Spark plugs, checking............................. 7-9
Specifications.......................................... 9-1
Starting the engine.................................. 6-1
Start switch ........................................... 4-10
Steering, checking ................................ 7-28
Storage ................................................... 8-3
Storage compartment ........................... 4-16
C
Cables, checking and lubricating.......... 7-25
Canister (for California only)................. 7-10
Care........................................................ 8-1
Catalytic converters.............................. 4-14
Centerstand and sidestand,
Identification numbers...........................10-1
Ignition circuit cut-off system.................4-21
Indicator and warning lights ....................4-2
K
checking and lubricating..................... 7-27
Clutch lever........................................... 4-10
Clutch lever free play, adjusting ........... 7-20
Coolant ................................................. 7-13
Coolant temperature warning light.......... 4-3
Key identification number......................10-1
L
Labels, location .......................................1-1
License plate light bulb, replacing.........7-34
Luggage strap holders ..........................4-20
D
M
Dimmer switch...................................... 4-10
Drive chain, cleaning and lubricating.... 7-24
Drive chain slack .................................. 7-23
T
Main switch/steering lock ........................4-1
Tail/brake light bulb, replacing.............. 7-33
Throttle cable free play, checking......... 7-17
Throttle grip and cable, checking
and lubricating .................................... 7-25
Tires...................................................... 7-18
Tool kit .................................................... 7-2
Troubleshooting.................................... 7-37
Troubleshooting charts ......................... 7-39
Turn signal indicator lights...................... 4-2
Maintenance and lubrication, periodic.....7-4
Maintenance, emission control system ...7-3
Maintenance record ..............................10-5
Matte color, caution.................................8-1
Model label............................................10-2
Multi-function meter unit..........................4-5
E
Engine break-in ...................................... 6-4
Engine idling speed, checking.............. 7-17
Engine oil and oil filter cartridge ........... 7-10
Engine stop switch................................ 4-10
Engine trouble warning light ................... 4-5
EXUP system ....................................... 4-20
N
Neutral indicator light ..............................4-2
Noise regulation ....................................10-4
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
Turn signal light bulb, replacing ............7-33
Turn signal switch .................................4-10
V
Valve clearance ....................................7-17
Vehicle identification number................10-1
W
Warranty, extended...............................10-9
Warranty, limited...................................10-7
Wheel bearings, checking.....................7-29
Wheel (front) .........................................7-35
Wheel (rear)..........................................7-36
Wheels..................................................7-20
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Weider Home Gym WESY39310 User Manual
West Bend Coffeemaker L 5227 User Manual
Whirlpool Appliance Trim Kit RF356BXDW0 User Manual
Whirlpool Ice Maker ECKMF 28 User Manual
Whirlpool Stove 1 User Manual
Xerox Fax Machine 1008M User Manual
Yamaha CD Player CDR200tx User Manual
Yamaha Stereo Amplifier DSP Z11 User Manual
Zanussi Dishwasher 502051 User Manual
Zanussi Oven ZCE 7680 User Manual