Xerox Washer AQLF9D 69 U User Manual

Instructions for

installation and use

WASHING MACHINE

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

Technical data

English,1

Description of the machine, 6-7

Touch control panel

Auto Dose System, 8-9

Running a wash cycle, 10

Wash cycles and options, 11

Table of wash cycles

Wash options

Detergents and laundry, 12

Detergent

Preparing the laundry

AQUALTIS

Washing recommendations

Load balancing system

AQLF9D 69 U

Precautions and advice, 13

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 14

Cutting off the water and electricity supplies

Cleaning the machine

Cleaning the detergent dispenser drawer

Caring for your appliance drum

Cleaning the pump

Checking the water inlet hose

Trouble shooting, 15-16

Assistance, 17-18

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the drain hose

• the supply voltage is included within the values i

ndicated on the Technical details table (see page 5);

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

• the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

65 - 100 cm

Your appliance is now supplied with a 13 amp fused plug

it can be plugged into a 13 amp socket for immediate

use. Before using the appliance please read the

instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

The drain hose may be

connected to an under-

sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the

spigot.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA approved

fuse to BS 1362 should always be used, and the fuse

cover re-fitted. If the fuse cover is lost, the plug must not

be used until a replacement is obtained.

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking or

the colour that is embossed in words on the base of the

plug. Replacements can be obtained directly from your

nearest Service Depot.

If it is place over the

edge of a basin or sink

be sure the free end of

the hose should not be

underwater.

Removing the plug:

If your appliance has a non-rewireable moulded plug and

you should wish to re-route the mains cable through

partitions, units etc., please ensure that either:

the plug is replaced by a fused 13 ampere rewireable

plug bearing the BSI mark of approval.

or:

! We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the appliance.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more than

15cms (6 inches). If the hose is pushed down too far,

this may cause the machine to self -syphon ie.

continuously empty as it is filling.

Disposing of the plug:

Ensure that before disposing of the plug itself, you make

the pins unusable so that it cannot be accidentally

inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

Green & Yellow Earth

Blue

Neutral

Live

Brown

• the socket is earthed and in compliance with the

applicable law;

• the socket is able to sustain the appliance's

maximum power load indicated in the Technical details

table (see page 5);

Download from Www.Somanuals.com. All Manuals Search And Download.

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or coloured

Red.

Connect Blue wire to terminal marked N or coloured

Black.

If a 13 amp plug (BS 1363) is used it must be fitted with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in accordance

with the following code:

BLUE

NEUTRAL (N)

LIVE (L)

BROWN

GREEN & YELLOW

EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the plug

by cutting the mains cable as close as possible to the

plug body and dispose of it as described above.

GREEN &

YELLOW

13 ampere fuse

BROWN

CROSS-BAR

CORD GRIP

BLUE

! The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave it

exposed to rain and thunderstorms.

! When the washing machine is installed, the mains

socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent or

dangerously compressed.

! The power supply cable must only be replaced by an

authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical data

Model

AQLF9D 69 U

width 59.5 cm

height 85 cm

depth 64,5 cm

Dimensions

Capacity

from 1 to 9 kg

Electrical

please refer to the technical data

plate fixed to the machine

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 62 litres

Water connections

Spin speed

up to 1600 rotations per minute

Energy rated

programmes

according to

regulation

programme

; temperature 60°C;

using a load of 9 kg.

EN 60456

This appliance conforms to the

following EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2006/95/EC (Low Voltage)

- 2002/96/EC

Download from Www.Somanuals.com. All Manuals Search And Download.

Description of the machine

CONTROL

PANEL

PORTHOLE DOOR

HANDLE

KICK STRIP

ADJUSTABLE FEET

PORTHOLE DOOR

TOUCH CONTROL PANEL

Always use the handle to

To adjust the settings, gently

press the icon inside the

sensitive (touch control) area

as illustrated in the figure.

open the porthole door (see

figure).

DETERGENT DISPENSER DRAWER

Standby mode

This washing machine, in compliance with new energy

saving regulations, is fitted with an automatic standby

system which is enabled after about 30 minutes if no

The detergent dispenser

drawer is located inside the

machine and can be

activity is detected. Press the ON-OFF

button briefly

accessed by opening the

and wait for the machine to start up again.

door.

Refer to the chapter "Auto

Dose System" for information

on operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

START/PAUSE button

with indicator light

WASH

Touch control panel

SPIN SPEED

SOFTENER

button

WASH CYCLE

SELECTOR knob

CYCLE

PHASE

icons

ECO

DETERGENT

button

TEMPERATURE

button

indicator light

DISPLAY

CHILD LOCK button

ON/OFF Button with

OPTION

buttons

DELAY

with indicator light

DETERGENT

DILUTION

button

indicator light

TIMER button

DOOR LOCKED

indicator light

again; the indicator light will flash in an orange colour. If the

“Door locked” indicator light is switched off, the door may

Button with ON/OFF indicator light: press this briefly to switch

the machine on or off. The green indicator light indicates that the

machine is switched on. To switch off the washing machine during

the wash cycle, press and hold the button for approximately 3

seconds; if the button is pressed briefly or accidentally the machine

will not switch off. If the machine is switched off during a wash

cycle, this wash cycle will be cancelled.

be opened. To start the wash cycle from the point at which it

was interrupted, press the button again.

DOOR LOCKED

indicator light: indicates that the

porthole door is locked. To open the door, pause the wash

cycle (see “Running a wash cycle”).

WASH CYCLE SELECTOR knob: may be turned in either

direction. To select the most suitable wash cycle, please refer

to the “Table of wash cycles”.

CHILD LOCK

button with indicator light: to activate or

deactivate the control panel lock, press and hold the button

for approximately 2 seconds. when the indicator light is

illuminated, the control panel is locked. This means it is

possible to prevent wash cycles from being modified

accidentally, especially where there are children in the home.

The knob will not move during the wash cycle.

TEMPERATURE

button: press to modify or exclude the

temperature setting; the value selected will appear on the

display above (see “Running a wash cycle”).

ECO indicator light: the

icon lights up when, after altering the

washing parameters, an energy saving of at least 10% is made.

Furthermore, before the machine enters “Standby” mode, the

icon will light up for a few seconds; when the machine is switched

off the estimated energy saving will be around the 80% mark.

SPIN SPEED CYCLE

button: press to modify or exclude

the spin cycle; the value selected will appear on the display

above (see “Running a wash cycle”).

DELAY TIMER

button: press to set a delayed start for

CHANGE LANGUAGE

the selected wash cycle; the set delay time will appear on the

The first time the machine is switched on, the first language

will flash on the display. The " ", "OK" and "V" symbols will

appear on the display, in line with the 3 buttons on the right-

hand side. The languages change automatically every 3";

alternatively, they can be changed by pressing the buttons next

to the " " and "V" symbols. Use the "OK" button to confirm the

language, which will be set after 2". If no buttons are pressed,

the automatic language change will begin again after 30".

The language may only be changed while the machine is

display above (see “Running a wash cycle”).

OPTION buttons with indicator lights: press to select the

available options. The indicator light corresponding to the

selected option will remain lit (see “Running a wash cycle”).

DETERGENT and

SOFTENER buttons : refer to

"Modifying pre-set parameters" in the chapter "Auto Dose

System".

DETERGENT DILUTION button: refer to "Filling the

tanks" in the chapter "Auto Dose System".

switched off. Press and hold the temperature

+spin

+delayed start buttons for 5''; a short beep sounds and

WASH CYCLE PHASE icons: these illuminate to indicate the

the set language flashes on the display. Press the buttons

next to the " " and "V" symbols to change the language. Use

the button next to the "OK" symbol to confirm the language,

which will be set after 2". If no buttons are pressed, the

language set previously will be displayed after 30".

Switch on the machine.

progress of the wash cycle (Wash

– Rinse

– Spin

–

Drain ). The text lights up when the cycle is complete.

START/PAUSE button with indicator light: when the green

indicator light flashes slowly, press the button to start a wash

cycle. Once the cycle has begun the indicator light will remain

lit in a fixed manner. To pause the wash cycle, press the button

Download from Www.Somanuals.com. All Manuals Search And Download.

Auto Dose System

Introduction

Filling the tanks:

This washing machine is

Open the detergent dispenser drawer in the "Auto Dose

System" mode (refer to "Detergent dispenser").

Slowly pour the detergent (B) and fabric softener (C)

until the tanks are completely filled (see picture).

equipped with two tanks: one

for liquid detergent (either

concentrated or diluted) with

a capacity of approx. 5.5 l

and another for liquid fabric

softener (either concentrated

or diluted) with a capacity of

approx. 3.5 l (see picture).

! Check the detergent/fabric

softener box to verify whether

it is diluted or concentrated

detergent. The automatic

dosing system intakes the

correct amount of detergent and fabric softener from the

tanks for each type of load and at the right time,

guaranteeing optimal washing results without wastage.

The amount of detergent/fabric softener can be modified

manually by pressing the DETERGENT and FABRIC

SOFTENER buttons (refer to "Modifying pre-set

To avoid exceeding the maximum capacity, a buzzer (beep)

will sound with growing intensity to signal the level and 3

long beeps will sound once the tank is completely full.

Start the wash cycle immediately after filling the tanks to

ensure that the dispenser is properly cleaned.The

parameters"). If you prefer, the washing machine can

also be used in the "traditional" mode, i.e. by adding the

detergent in the dispenser; the machine will automatically

detect the detergent and will not use the tanks.

respective icons

(for the detergent) and

fabric softener) will light up gradually to signal the level.

(for the

Detergent dispenser

"Traditional" mode.

Pull out the detergent dispenser drawer up to the first

stop point to add the detergent (either liquid or powder

detergent), bleach or other additives (e.g. whiteners) and

the pre-wash detergent for washing in the "traditional"

mode (refer to "Traditional” mode).

The filling time depends on the density of the product.

Very dense products will take longer to fill.

"Auto Dose System” mode.

In order to fill the detergent

Close the detergent dispenser drawer only once the

compartments are completely empty.

and fabric softener tanks,

the detergent dispenser

drawer must be fully

extracted: open the dispenser

Select the density of the detergent added (either concentrated

or liquid) by pressing the appropriate button

Concentrated

drawer up to the first stop

point then press the lever (A)

Diluted

and open up to the second

stop point, making sure that

The machine will store the selection.

If no option is selected, the detergent intake option will

be pre-set to "diluted".

it is fully extracted. Avoid

moving the dispenser

Use button to set the amount of fabric softener that

will be automatically extracted by the machine:

drawer during filling operations. Once the tanks have

been filled (refer to "Filling the tanks"), the machine can run

up to 60 cycles before the detergent finishes (*).

1) If concentrated softener is used, we recommend

selecting the first level (

with one bar) and, if necessary,

First-time use

stepping up by a single position ( with 2 bars) to

increase detergent intake.

2) If diluted softener is used, we recommend setting level

Turn the washing machine on by pressing the ON/OFF

button. The first wash cycle must be carried out without

laundry and by adding detergent in the detergent

dispenser (refer to "Traditional” mode); set the

programme " " (Cotton 90°) without pre-wash and

without filling the tanks.

3 (

with 3 bars) and to then either increase/decrease

the amount of fabric softener to be extracted.

3) To exclude the use of fabric softener, press

bars disappear (also refer to "Modifying pre-set

parameters").

until the

(*) with an average load of 4 kg, 40°C Cotton programme, "medium" water

hardness level and dirt level set to 3.

Download from Www.Somanuals.com. All Manuals Search And Download.

Signals for successive refilling:

Cleaning cycle set by the user:

Once, at the end of a cycle, the level of detergent/fabric

softener falls below the level required for a successive

wash cycle, the display will visualise the relative

messages "At end of cycle refill detergent" or "At end

of cycle refill softener" or "At end of cycle refill

tanks". If the tanks are not filled, the successive wash

cycles in Auto Dose System will be carried out without

any intake of detergent.

Run the cleaning cycle (with empty drum) if you require

adding a different product to the previous one or if the

tanks have been incorrectly filled (e.g. fabric softener

has been erroneously poured into the detergent tank or

vice-versa). Press button

activate cleaning of the detergent tank, button

cleaning the fabric softener tank or button for

and hold for 5 sec. to

for

cleaning both tanks. Keep pressing for a further 3 sec.

(the countdown "4-3-2-1" will appear in the top right

corner) until "CLEAN-GO" pops up.

! We suggest adding detergent and fabric softener

ONLY after the machine's signal.

The cleaning cycle lasts about 40' if the tanks are initially

empty; if not, the cycle will last longer. The icons

indicating that the tanks are empty will appear on the

display.

! NEVER mix two different detergents; always clean out

the tank before adding a new type of detergent (refer to

"Cleaning cycle set by the user").

Using the "Auto Dose System"

If the compartments have been filled with detergent and

fabric softener, you may start using the machine (refer

to "Running a wash cycle").

"Traditional" mode

Pull out the detergent dispenser drawer up to the first

stop point (see picture) then pour the amount of

detergent and other additives (e.g. bleach) required for a

single wash cycle directly into the dispenser.

1. pre-wash compartment:

Powder detergents for pre-washing and powder

additives may only be used in the traditional mode or

using the "Auto Dose System", by placing the additives

directly inside the drum, preferably in conjunction with

the "laundry ball".

use powder detergent only.

2. main wash

compartment: use powder

Modifying pre-set parameters:

or liquid detergent. If the

The machine automatically intakes detergent on the

basis of the selected programme, wash load and water

hardness. However, the amount of detergent/fabric

softener used may be modified.

latter is used, we

recommend pouring it into

the dispenser immediately

before starting the washing

button: press to increase, decrease and to exclude

detergent intake.

machine and without

running a pre-wash cycle.

3. ! Do not pour anything in this compartment.

Tablet detergent or the relative "laundry ball" must be

added directly inside the drum. In this event, deactivate

button: press to increase, decrease and to exclude

fabric softener intake.

the "Auto Dose System" (by pressing the

button until

the relative vertical bars disappear from the display).

Do not pour any fabric softener as the appropriate

quantity required for each wash cycle will be

automatically extracted.

To deactivate fabric softener intake, press the

until the vertical bars disappear from the display.

button

The level of detergent/fabric softener suggested by the

machine is indicated by 3 bars.

For wool and silk garments, we recommend using a

special detergent which must be poured directly into the

detergent dispenser (compartment 2).

Less than 3 bars indicates a lower level of detergent/

fabric softener compared to that suggested by the

machine, while more than 3 bars indicates a higher level

of detergent/fabric softener.

Running the wash cycle:

Select the programme and the compatible options on

the basis of the required need and type of load.

Cleaning the tanks:

Tank cleaning cycles can either be automatic or pre-set

by the user.

Automatic cleaning:

The washing machine carries out an automatic cleaning cycle

during the rinse cycle if the level of detergent that remains is

insufficient for carrying out a successive wash cycle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Running a wash cycle

and the display will show "Ends in:" and the time

remaining until the end of the cycle. To remove the

delayed start option, press the button until the display

WARNING: before you use the washing machine for

the first time, run a wash cycle with detergent and no

laundry, using the 90° cottons cycle without pre-wash.

shows the text OFF; the

symbol will disappear.

1. SWITCH THE MACHINE ON. Press the

button.

Modify the cycle settings.

• Press the button to activate the option; the name

of the option will then appear on the display and

the corresponding indicator light will illuminate.

• Press the button again to deactivate the option;

the name of the option will then appear on the

display followed by the text OFF, and the

All the indicator lights will illuminate for 1 second and

the text AQUALTIS will appear on the display; the

indicator light corresponding to the

button will then

remain lit in a constant manner and the START/

PAUSE indicator light will flash.

2. SELECT THE PROGRAMME. Turn the PROGRAMME

KNOB left or right, until the required programme has been

selected; the name of the programme will appear on the

display. A temperature and spin speed is set for each

programme; these may be adjusted. The cycle duration

will also appear on the display.

corresponding indicator light will switch off.

! If the selected option is not compatible with the

selected wash cycle, this incompatibility will be

signalled by the flashing of the indicator light and a

sound alert (3 beeps); the option will not be activated.

! If the selected option is not compatible with another

option that has been selected previously, the indicator

light corresponding to the first option selected will flash

and only the second option will be activated; the

indicator light corresponding to the button will remain

lit in a constant manner.

3. LOAD THE LAUNDRY. Open the porthole door.

Load the laundry, making sure you do not exceed the

maximum load value indicated in the table of wash

cycles on the following page.

4. MEASURE OUT THE DETERGENT. There is no

need to add detergent when the "Auto Dose System"

mode is used, as the machine automatically intakes

detergent on the basis of the selected programme,

type of load and water hardness. Refer to the

paragraph "Traditional” mode for implementing the

traditional operation mode.

! The options may affect the recommended load value and/

or the duration of the cycle.

7. START THE PROGRAMME. Press the START/

PAUSE button. The corresponding indicator light

remains lit in a fixed manner and the porthole door

locks (the

DOOR LOCKED indicator light

5. CLOSE THE PORTHOLE DOOR.

illuminates). The icons corresponding to the wash

cycle phases will light up during the cycle to indicate

which phase is currently in progress. To change a

wash cycle once it has already started, pause the

washing machine by pressing the START/PAUSE

button; then select the desired cycle and press the

START/PAUSE button again. To open the door during

a wash cycle, press the START/PAUSE button; if the

6. CUSTOMISE THE WASH CYCLE. Use the

relevant buttons on the control panel:

Modify the temperature and/or spin speed.

The machine automatically displays the maximum

temperature and spin speed values set for the

selected cycle, or the most recently-used settings if

they are compatible with the selected cycle. The

temperature can be decreased by pressing the

button, until the cold wash “OFF” setting is reached.

The spin speed may be progressively reduced by

DOOR LOCKED

indicator light is switched off you

may open the door. Press the START/PAUSE button

again to restart the wash cycle from the point at

which it was interrupted.

pressing the

button, until it is completely excluded

“OFF”. If these buttons are pressed again, the

maximum values are restored.

8. THE END OF THE WASH CYCLE. This is indicated

by the illuminated text END. The porthole door may be

opened immediately. If the START/PAUSE indicator light

is flashing, press the button to end the cycle. Open the

door, unload the laundry and switch off the machine.

! Exception: if the “Cottons” programme is selected, the

temperature can be increased up to a value of 90°C.

Set a DELAY TIMER.

To set a delayed start for the selected cycle, press the

corresponding button repeatedly until the required delay

period has been reached. During the setting procedure,

the delay period and the text "Starts in:" will be

! If you wish to cancel a cycle which has already begun,

press and hold the button until the cycle stops and

the machine switches off.

displayed, along with the flashing

delayed start has been set, the

fixed on the display, which will also indicate the duration

of the selected cycle with the text "Ends in:" and the

cycle duration. Press the DELAY TIMER button just

once to display the delay time set previously.

After the countdown has begun, the display will show

the text "Starts in:" and the delay period. Once the set

delay time has elapsed, the machine will begin its cycle

symbol. After the

symbol will remain

Bag for quilts, curtains and delicate garments

The Aqualtis washing machine makes it easier for you to

wash even the most valuable and delicate garments in

complete confidence thanks to the special bag which

protects the laundry (this is supplied with the machine).

We recommend that the bag is used every time you

wash quilts and padded items with an outer layer made

using synthetic material.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wash cycles and options

Table of wash cycles

Detergent and additives

Max.

temp.

(°C)

Max.

speed

(rpm)

Max.

load

(kg)

Cycle

duration

Icon Description of the wash cycle

Detergent for Detergent Fabric

prewash

for wash softener

Cottons wash cycles

Cotton with pre-wash

(Add detergent to the relevant compartment).

90°

1600

60°

(Max. 90°)

Cotton (1): heavily soiled whites and resistant colours.

Cotton (2): heavily soiled whites and delicate colours.

Coloured Cotton (3)

40°

1600

600

Shirts

Jeans

800

Special programmes

Baby: heavily soiled delicate colours

Durable Synthetics

40°

60°

40°

60°

30°

40°

800

1600

1200

Delicate Synthetics

"Bed & Bath" for bedlinen and towels.

Duvets: for down-stuffed garments.

Silk: for garments in silk and viscose, lingerie.

Wool: for wool, cashmere, etc.

3,5

600

Mix 30': to refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand)

30°

800

3,5

Partials wash cycles

Rinse

Spin

1600

Drain

(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this

value will then be shown on the display.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 60456: set wash cycle withatemperatureof60°C.

2) Long wash cycle for cottons: set wash cycle with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle with a temperature of 40°C.

Wash options

Time Saver

If you select this option, the wash cycle duration will be

reduced by 30%-50%, depending on the selected cycle,

thereby guaranteeing simultaneous water and energy

saving. Use this cycle for lightly soiled garments.

Extra rinse

By selecting this option, the efficiency of the rinse is

increased and optimal residual detergent removal is

guaranteed. It is particularly useful for skin which is

sensitive to detergents. We recommend this option is

used with a full load of washing, or when a large amount

of detergent is required.

! It cannot be used in conjunction with

Eco Option

The Eco Option saves energy by not heating the water

used to wash your laundry – an advantage both to the

environment and to your energy bill. Instead, intensified

wash action and water optimisation ensure great wash

results in the same average time of a standard cycle.

For the best washing results we recommend the usage

of a liquid detergent.

Easy Iron

By selecting this option, the wash and spin cycles will be

modified in order to reduce the formation of creases.

At the end of the cycle the washing machine drum

will rotate slowly; the “Easy Iron” and START/PAUSE

indicator lights will flash. To end the cycle press the

START/PAUSE button or the “Easy Iron” button.

! It cannot be used in conjunction with

For the Silk

wash cycle, the machine will end the

cycle while the laundry is soaking and the “Easy Iron”

indicator light will flash. To drain the water so that the

laundry may be removed, press the START/PAUSE

button or the “Easy Iron” button.

! It cannot be used in conjunction with

Download from Www.Somanuals.com. All Manuals Search And Download.

Detergents and laundry

Detergent

bacteria by using a greater quantity of water and

The type and quantity of detergent required depend on

the type of fabric you are washing (cotton, wool, silk,

etc.), as well as its colour, the washing temperature, the

level of soiling and the hardness of the water in the area.

Whenever the detergent and fabric softener “Auto Dose

System” is activated, this washing machine helps to

prevent wastage and to protect the environment,

besides guaranteeing optimal washing performance.

We recommend the following:

optimising the effect of special disinfecting additives

added to the detergent. At the end of the wash cycle,

the machine will slowly rotate the drum; to end the cycle

press the START/PAUSE button.

Silk: use the special “Silk”

wash cycle to wash all silk

garments. We recommend the use of special detergent

which has been designed to wash delicate clothes.

Curtains: use the “Silk” wash cycle. These should

be folded and placed inside the bag provided.

• Use powder detergent for carrying out a pre-wash

and pour in the "traditional" mode.

• Use liquid detergents for delicate cotton garments and

for all low-temperature wash cycles.

Wool: Hotpoint is the only washing machine brand to

have been awarded the prestigious Woolmark Platinum

Care endorsement (M.0508) by the Woolmark Company,

which means that all woollen garments may be washed

in the washing machine, even those which state “hand

• When activating the "Auto Dose System" mode, use

liquid detergent and fabric softeners only. Never add

ultra-concentrated detergents (e.g. "Gel" type

detergents or similar).

wash only”

on the label. The “Wool” wash cycle can

be used to wash all woollen garments in the washing

machine while guaranteeing optimum performance.

Duvets: to wash double or single duvets (the weight of

which should not exceed 3,5 kg), cushions or clothes

padded with goose down such as puffa jackets, use the

• Use gentle liquid detergents for wool and silk

garments and pour in the "traditional" mode.

! Never mix two different detergents; always clean out

the tank before adding a new type of detergent.

special “Duvets”

wash cycle. We recommend that

duvets are placed in the drum with their edges folded

inwards (see figure) and that no more than ¾ of the total

volume of the drum is used.

The detergent should be poured into the relevant

compartment - or the dispenser placed directly inside the

drum - before the wash cycle begins. In the latter case, it will

not be possible to select the Cottons with pre-wash cycle.

! Do not use hand washing detergents because these

create too much foam.

Preparing the laundry

• Shake out the garments before loading them into the

machine.

• Divide the laundry according fabric type (symbol on the

washing instruction label) and colour, making sure you

separate the coloured garments from the white ones;

• Empty all pockets and check the buttons;

• Do not exceed the values listed in the “Table of wash

cycles”, which refer to the weight of the laundry when dry.

Quilts: to wash quilts with a synthetic outer layer, use

the bag provided and set the wash cycle to “Duvets”

Bedlinen and towels: use the “Bed & Bath”

to wash laundry from all over the house; this optimises

cycle

How much does your laundry weigh?

1 sheet

400-500 g

150-200 g

400-500 g

900-1200 g

150-250 g

400-500 g

150-200 g

fabric softener performance and helps you save time and

energy. We recommend the use of powder detergent.

Stubborn stains: it is wise to treat stubborn stains with

solid soap before washing, and to use the Cottons with

pre-wash cycle.

1 pillowcase

1 tablecloth

1 bathrobe

1 towel

1 pair of jeans

1 shirt

Load balancing system

Before every spin cycle, to avoid excessive vibrations

before every spin and to distribute the load in a uniform

manner, the drum rotates continuously at a speed which

is slightly greater than the washing rotation speed. If,

after several attempts, the load is not balanced

correctly, the machine spins at a reduced spin speed. If

the load is excessively unbalanced, the washing

machine performs the distribution process instead of

spinning. To encourage improved load distribution and

balance, we recommend small and large garments are

mixed in the load.

Washing recommendations

Shirts: use the special “Shirts”

wash cycle to wash

shirts in different fabrics and colours to guarantee they

receive the best possible care.

Jeans: use the special “Jeans”

wash cycle for all

denim garments; turn inside out before washing and use

a liquid detergent.

Baby: use the special “Baby”

wash cycle to remove

the soiling typically caused by babies, while removing all

traces of detergent from nappies in order to prevent the

delicate skin of babies from suffering allergic reactions.

The cycle has been designed to reduce the amount of

Download from Www.Somanuals.com. All Manuals Search And Download.

Precautions and tips

! The machine was designed and constructed in

accordance with international safety regulations. The

following information is provided for safety reasons and

must therefore be read carefully.

For more information relating to the correct disposal of

household appliances, owners should contact their

local authorities or appliance dealer.

Opening the porthole door manually

General safety

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

• This appliance is not intended for use by persons

(including children) with reduced physical, sensory or

mental capabilities, or lack of experience and

knowledge, unless they have been given supervision

or instruction concerning use of the appliance by a

person responsible for their safety. Children should be

supervised to ensure that they do not play with the

appliance.

1. remove the plug from the

electrical socket.

2. make sure the water level

inside the machine is lower

than the door opening; if it is

not, remove excess water

using the drain hose,

• This appliance was designed for domestic use only.

• Do not touch the machine when barefoot or with wet

or damp hands or feet.

collecting it in a bucket as

indicated in the figure.

• Do not pull on the power supply cable when

unplugging the appliance from the electricity socket.

Hold the plug and pull.

3. remove the cover panel on the lower front part of the

washing machine (see overleaf).

• Do not touch the drained water as it may reach

extremely high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent

accidental opening.

4. pull outwards using the

tab as indicated in the figure,

until the plastic tie-rod is

freed from its stop position;

pull downwards until you

hear a “click”, which

• If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

indicates that the door is

now unlocked.

• Always keep children well away from the appliance

while it is operating.

• If it must be moved, proceed with the help of two or

three people and handle it with the utmost care.

Never try to do this alone, because the appliance is

very heavy.

5. open the door; if this is

still not possible repeat the

procedure.

• Before loading laundry into the washing machine,

make sure the drum is empty.

Disposal

• Disposing of the packaging materials: observe local

regulations so that the packaging may be re-used.

• The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states

that household appliances should not be disposed of

using the normal solid urban waste cycle. Exhausted

appliances should be collected separately in order to

optimise the cost of re-using and recycling the

materials inside the machine, while preventing

potential damage to the atmosphere and to public

health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations

regarding separated waste collection.

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and maintenance

Cutting off the water and electricity

supplies

To access the pre-chamber:

• Turn off the water tap after every wash cycle. This will

limit wear on the hydraulic system in the machine and

help to prevent leaks.

• Unplug the appliance when cleaning it and during all

maintenance work.

Cleaning the machine

1. take off the cover panel on the front of the machine

by first pressing it in the centre and then pushing

downwards on both sides until you can remove it (see

figures);

The outer parts and rubber components of the appliance

can be cleaned using a soft cloth soaked in lukewarm

soapy water. Do not use solvents or abrasives.

2. position a container so

that it will collect the water

which flows out

Cleaning the detergent dispenser drawer

(approximately 1.5 l) (see

figure);

3. unscrew the lid by

rotating it in an anti-

clockwise direction (see

figure);

4. clean the inside thoroughly;

5. screw the lid back on;

To pull out the dispenser drawer, open until the first stop

point then press lever A to open completely; finally, press

one of the levers D and pull the drawer outwards (see

picture).

6. reposition the panel, making sure the hooks are

securely in place before you push it onto the appliance.

Wash it under running water; this procedure should be

effected regularly. Be careful to remove any detergent

residues from the dispenser drawer socket on the

machine.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

Keep the drawer to the left hand side when replacing it

to ensure that it centres the guides and to prevent it

from jamming.

Caring for your appliance drum

• Always leave the door ajar to prevent unpleasant

odours from forming.

Cleaning the pump

The washing machine is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

protective pre-chamber at the base of the pump.

! Make sure the wash cycle has finished and unplug the

appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Trouble shooting

Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre

(see “Assistance”), make sure that the problem cannot be not solved easily using the following list.

Problem:

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or not enough to make

contact.

• There is no power in the house.

The washing machine does not

switch on.

The wash cycle does not start.

• The door is not closed properly.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A DELAY TIMER has been set.

The washing machine does not fill • The water inlet hose is not connected to the tap.

• The hose is bent.

with water.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• If you have selected the “Baby ” cycle or the “Easy iron

” option, when

The washing machine door

remains locked.

the wash cycle has finished the machine will slowly rotate the drum; to end

the cycle press the START/PAUSE button or the “Easy iron ” button. If

you have selected the “Silk ” wash cycle, the machine will end the cycle

while the laundry is soaking; to drain the water so that the laundry may be

removed, press the START/PAUSE button or the “Easy iron

” button.

• The drain hose is not fitted at a height between 65 and 100 cm from the

floor (see “Installation”).

The machine continuously fills

with water and drains.

• The free end of the hose is under water (see “Installation”).

• If the dwelling is on one of the upper floors of a building, there may be

problems relating to water drainage, causing the washing machine to fill

with water and drain continuously. Special anti-draining valves are available

in shops and help to prevent this inconvenience.

• The wall drainage system is not fitted with a breather pipe.

The washing machine does not

drain or spin.

• The wash cycle does not include draining: Some wash cycles require the

drain phase to be started manually (see “Wash cycles and options”).

• The “Easy iron” option is enabled: to complete the wash cycle, press the

START/PAUSE button (“Wash cycles and options”).

• The drain hose is bent (see Installation).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The machine is not level (see “Installation” ).

• The machine is trapped between cabinets and walls (see “Installation”).

• The load is unbalanced (see “Detergents and laundry”).

The machine vibrates a lot during

the spin cycle.

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser is blocked (to clean it, see “Care and

maintenance”).

The washing machine leaks.

• The drain hose is not fixed in place properly (see “Installation”).

The icons corresponding to the

“Phase in progress” flash rapidly

at the same time as the ON/OFF

indicator light.

• Switch off the machine and unplug it, wait for approximately 1 minute and

then switch it back on again. If the problem persists, contact the Technical

Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washing machines” or “hand and machine wash”, or the like).

• Too much detergent was used.

There is too much foam.

The washing machine door

remains locked after a blackout.

• Perform the manual unlocking procedure (see “Precautions and tips”).

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting:

Possible causes / Solutions:

The machine's washing

performance is unsatisfactory.

• The tanks have not been loaded correctly (e.g. fabric softener has been

added instead of detergent or vice-versa)

• Two different types of detergent/fabric softener have mixed.

! NEVER mix two different detergents; always clean out the tanks before adding

a new type of detergent.

• The "Auto Dose System” is blocked due to prolonged lack of use: carry

out a tank cleaning cycle (refer to "Cleaning cycle pre-set by user").

What happens if the tanks are • Buzzers (Beep) and visual signals (icons appearing on the display) indicate

loaded even if they are already full? that the tank is full. If further detergent/fabric softener is added, the excess

quantity will fall into the drum and will be washed away with the next cycle.

What happens if the dispenser is

used in the traditional mode while

the tanks are still full?

• The machine will automatically track whether powder or liquid detergent

has been loaded in the traditional mode and will not intake any amount of

detergent from the tank. Fabric softener can only be used in the "Auto

Dose System” mode.

Can the tanks also be used for

powder detergent?

• No, powder detergent can only be used in the traditional mode.

Can powder detergent fall into the

tanks?

• No, there is a barrier to prevent powder detergent from falling into one of

the tanks even if the dispenser is open in the "Auto Dose System" position

(i.e. completely open).

What happens if the dispenser is • If the dispenser is not completely open, the detergent or fabric softener

not opened properly when filling the that has been added will fall into the drum and will be washed away with

tanks?

the next cycle.

What happens if detergent and

fabric softener are erroneously

inverted?

• The washing machine will wash with unsatisfactory results, the tanks will

have to be emptied and subjected to a manual cleaning cycle.

What happens if different

detergents are mixed before the

tanks are empty?

• The machine will wash normally although we recommend only refilling the

tanks after the signal emitted by the machine; do not mix different

detergents/fabric softeners.

! Note: To exit “Demo mode”, press and hold the two “ON/OFF”

and “START/PAUSE”

buttons simultaneously for 3 seconds.

Download from Www.Somanuals.com. All Manuals Search And Download.

Assistance

Guarantee

12 Months Parts and Labour Guarantee

Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of

breakdown repairs for twelve months from the date of purchase.

This gives you the reassurance that if, within that time, your appliance is proven to be defective

because of either workmanship or materials, we will, at our discretion, either repair or replace the

appliance at no cost to you.

This guarantee is subject to the following conditions:

The appliance has been installed and operated correctly and in accordance with our

operating and maintenance instructions.

The appliance is used only on the electricity or gas supply printed on the rating plate.

The appliance has been used for normal domestic purposes only.

The appliance has not been altered, serviced, maintained, dismantled, or otherwise

interfered with by any person not authorised by us.

Any repair work must be undertaken by us or our appointed agent.

Any parts removed during repair work or any appliance that is replaced become our property.

The appliance is used in the United Kingdom or Republic of Ireland.

The guarantee does not cover:

Damage resulting from transportation, improper use, neglect or interference or as a result

of improper installation.

Replacement of any consumable item or accessory . These include but are not limited to: plugs,

cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.

Replacement of any removable parts made of glass or plastic.

THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL

OR NON-DOMESTIC PREMISES.

5 Year Parts Guarantee

Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on

you registering your appliance with us and the parts being fitted by one of our authorised engineers.

There will be a charge for our engineer's time. To activate the extra parts warranty on your

appliance, simply call our registration line on 08448 24 24 24 (ROI 01 230 0800).

Extended Guarantees

We offer a selection of repair protection plans that enable you to fully cover yourself against the

expense of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on

08448 226 226 (Republic of Ireland 01 230 0233).

Free Helpdesk Service

We have a dedicated team who can provide free advice and assistance with your appliance if you

experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint

Service Hotline on 08448 224 224 (Republic of Ireland 0818 313 413) for telephone

assistance, or, where necessary, to arrange for an engineer to call. If we cannot resolve the

technical problem we will replace your machine or, if you prefer, give you your money back.

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

No one is better placed to care for your Hotpoint appliance during the course of its

working life than us - the manufacturer.

Essential Contact Information

Hotpoint Service

We are the largest service team in Europe offering you access to 400 skilled telephone advisors and

1000 fully qualified engineers on call to ensure you receive fast, reliable, local service.

UK: 08448 224 224

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Please note: Our advisors will require the following information:

Model number:

Serial number:

Parts and Accessories

We supply a full range of genuine replacement parts as well as accessory products that protect and

hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.

UK: 08448 225 225

Republic of Ireland: 0818 313 413

www.hotpointservice.co.uk

Appliance Registration

We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts

guarantee you must register your appliance with us.

UK: 08448 24 24 24

Republic of Ireland: 01 230 0800

www.hotpointservice.co.uk

Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB

Indesit Company Unit 49 Airways Industrial Estate,Dublin 17

Recycling & Disposal Information

As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the

right to use quality, recycled components to keep down customer costs and minimise material

wastage.

Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,

remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts

Download from Www.Somanuals.com. All Manuals Search And Download.

195077709.05

09/2009

Xerox Fabriano

Download from Www.Somanuals.com. All Manuals Search And Download.

Whirlpool Convection Oven GM8155XJB0 User Manual
Whirlpool Freezer EV150N User Manual
Whistler Home Security System WIC 2409C User Manual
Whynter Air Conditioner ARC 12S User Manual
Wolfgang Puck Slow Cooker WPSC0017C User Manual
Woodstock Air Cleaner W1746 User Manual
Worth Data Scanner P11 12 User Manual
Xerox Printer 019 6400 User Manual
Xerox Printer Phaser 3120 User Manual
Zanussi Dishwasher 132713 User Manual