GPIB
ENET
Operating Manual
GPIB and Ethernet
Interface for
XG Series
Programmable DC
Power Supplies
Download from Www.Somanuals.com. All Manuals Search And Download.
XG 850 Watt Series
Programmable DC Power
Supply
Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
About Xantrex
Xantrex Technology Inc. is a world-leading supplier of advanced power electronics and controls with
products from small mobile units to utility-scale systems for wind, solar, batteries, fuel cells,
microturbines, and backup power applications in both grid-connected and stand-alone systems. Xantrex
products include inverters, battery chargers, programmable power supplies, and variable speed drives
that convert, supply, control, clean, and distribute electrical power.
Trademarks
XG 850 Watt Series Programmable DC Power Supply is a trademark of Xantrex International. Xantrex
is a registered trademark of Xantrex International.
Other trademarks, registered trademarks, and product names are the property of their respective owners
and are used herein for identification purposes only.
Notice of Copyright
XG 850 Watt Series Programmable DC Power Supply Operating Manual© November 2007 Xantrex
International. All rights reserved.
Exclusion for Documentation
UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC.
(“XANTREX”)
(A) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF
ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS MANUALS OR OTHER
DOCUMENTATION.
(B) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES, COSTS OR
EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL OR INCIDENTAL,
WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY SUCH
INFORMATION WILL BE ENTIRELY AT THE USER’S RISK; AND
(C) REMINDS YOU THAT IF THIS MANUAL IS IN ANY LANGUAGE OTHER THAN
ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF THE
TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED. APPROVED XANTREX
CONTENT IS CONTAINED WITH THE ENGLISH LANGUAGE VERSION WHICH IS POSTED
AT WWW.PROGRAMMABLEPOWER.COM.
Date and Revision
November 2007 Revision A
Part Number
M370078-01
M370078-01
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Numbers (FGAs)
XG6-110
XG8-100
XG12-70
XG20-42
XG33-25
XG40-21
XG60-14
XG80-10.5
XG100-8.5
XG150-5.6
XG300-2.8
XG600-1.4
Part Numbers for Rack Mount Kits
Rack Mount Kit
Part Number
RM-D-XG1
RM-S-XG1
RM-XG
Dual XG 850 Watt
Single XG 850 Watt
Rack mount rails for
XG Series
Contact Information
Telephone: 1 800 733 5427 (toll free North America)
1 858 450 0085(direct)
Fax:
1 858 458 0267
Email:
Web:
M370078-01
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Purpose
This Operating Manual provides explanations and procedures for
programming the XG 850 Watt Series Programmable DC Power Supply
from the GPIB interface and connecting and configuring the power supply
to the Ethernet.
Scope
The Manual covers the GPIB and Ethernet interface options only. Refer to
the XG 850 Watt Series Programmable DC Power Supply Operating
Manual (Part number: M370078-01) for installation, operating procedures,
setup, calibration and troubleshooting for your power supply.
Audience
The Manual is intended for the user who is familiar with electronic power
supplies, Constant Current and Constant Voltage operating modes and the
control of output power. The user should be familiar with practicing safe
techniques while making supply or pin connections. The user should also
have experience with network-based communications software and
protocols.
Organization
Warranty and Product information.
the XG 850 Watt Series Programmable DC Power Supply from the GPIB
connect and configure the power supply to the ENET.
the combined ENET and RS-485 communication and for ENET
communication.
Appendix B, “Links” provides the Web site links for relevant third party
vendors.
M370078-06
v
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Manual
Conventions Used
The following conventions are used in this Manual.
WARNING
Warnings identify conditions or practices that could result in personal injury or
loss of life.
CAUTION
Cautions identify conditions or practices that could result in damage to the unit or
other equipment.
Important: Important notes provide information that is important for you to
know. They are not as serious as Cautions or Warnings.
Related Information
For related materials on this product, see also:
•
•
•
XG 850 Watt Series Programmable DC Power Supply Operating
Manual (Part number: M370078-01).
XG 850 Watt Series Programmable DC Power Supply Rack Mount
Kit Options (Part number: M370078-05).
XG 850 Watt Series Programmable DC Power Supply: Quick
Reference Guide (Part number: M370078-04). This document is
included with your power supply and provides a quick start on using
the front panel interface.
More information about Xantrex Technology Inc. as well as its products
and services is available at www.programmablepower.com.
vi
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING: High Energy and High Voltage
Exercise caution when using a power supply. High energy levels can be stored at
the output voltage terminals on a power supply in normal operation. In addition,
potentially lethal voltages exist in the power circuit and on the output and sense
connectors of a power supply with a rated output greater than 40 V. Filter
capacitors store potentially dangerous energy for some time after power is
removed.
WARNING
Operate the power supply in an environment free of flammable gases or fumes.
To ensure that the power supply's safety features are not compromised, use the
power supply as specified in this manual and do not substitute parts or make any
unauthorized modifications. If service is necessary, please return the power
supply to the factory Authorized Service Center. See “Return Material
Authorization Policy” on page WA–3.
WARNING: Limitations on use
The XG 850W GPIB and Ethernet Interface Option is not intended for use in
connection with life support systems or other medical equipment or device.
M370078-06
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
1
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1–2
Codes and Standards - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1–2
Communication with Your Device - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1–4
Selecting a Communication Port - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -1–4
2
Overview - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–2
Basic Section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–2
System Requirements - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–2
Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–2
ENET Connector - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–4
Software Installations - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–9
Selecting a Network Adapter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11
End of Message - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–19
Establishing Communication with the Power Supply - - - - - - - - - - - - - - - - - - 2–23
Advanced Section - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–26
A
B
Troubleshooting for ENET Communication - - - - - - - - - - - - - - - - - - - - - - - - A–3
Links
Links - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - B–2
Warranty and Product Information - - - - - - - - - - - - - - - - - - - - - - - - - -WA–1
M370046-06
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1-1 GPIB Connector and Pins - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2
Figure 1-2 Scanning for Instruments - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–5
Figure 1-3 Instrument Properties - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–6
Figure 1-4 ID String Query- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–6
Figure 2-1 Computer or HUB Plug - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2
Figure 2-2 Power Supply Plug - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3
Figure 2-3 RJ-45 Plug - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3
Figure 2-4 Scheme of ENET Cross-Cable- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3
Figure 2-8 LAN Properties Dialog Box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–7
Figure 2-10 DeviceInstaller Setup Wizard - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–9
Figure 2-11 Select Installation Folder Window - - - - - - - - - - - - - - - - - - - - - - - - - - 2–10
Figure 2-12 Multiple Network Adapters- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–11
Figure 2-13 Selecting Network Adapter - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12
Figure 2-14 Auto-IP Address Message- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–12
Figure 2-16 IP Address Details Window- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–14
Figure 2-17 Entering the Lantronix Interface- - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–15
Figure 2-18 Lantronix XPort® Interface- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–16
Figure 2-19 Assigning IP Settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–17
Figure 2-20 HyperTerminal Connection - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–19
Figure 2-21 Connection Description Window - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–20
Figure 2-22 New Connection Dialog Box- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–20
Figure 2-23 Main Terminal Window - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–21
Figure 2-24 ENET Properties Window- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–22
Figure 2-25 XG-ENET Properties Dialog Box- - - - - - - - - - - - - - - - - - - - - - - - - - - 2–22
Figure 2-26 ASCII Setup Dialog Box- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–23
Figure 2-27 Main HyperTerminal Window- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–24
Figure 2-28 Saving Session - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–24
M370046-06
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures
Figure 2-29 Saved Session- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–25
Figure 2-31 HyperTerminal Session - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–28
Figure 2-32 System with Two Connected Devices- - - - - - - - - - - - - - - - - - - - - - - - - 2–29
Figure 2-33 ENET and RS-485 Bus - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–30
Figure 2-34 HyperTerminal Window- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–31
xii
M370046-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table 2-1
Table 2-2
Description of PIN on RJ-45 Plug - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–3
Description of LEDs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–4
Table A-1 Troubleshooting for ENET – RS-485 Communication- - - - - - - - - - - - - - A–2
Table A-2 Troubleshooting for ENET Communication- - - - - - - - - - - - - - - - - - - - - A–3
M370046-06
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
GPIB
Overview
The power supply can be programmed from a remote terminal using a
GPIB interface. Communication over the GPIB interface meets IEEE
488.2 standards and are Standard Commands for Programmable
Instrumentation (SCPI) compliant.
Codes and Standards
The GPIB interface of the XG 850 Watt Series Programmable DC Power
Supply has been implemented according to IEEE Std 488.1-1987, IEEE
Standard Digital Interface for Programmable Instrumentation. The
communication protocol complies with IEEE 488.2-1992.
GPIB Interface Description and Required Cable Size
The GPIB interface is an 8-bit parallel data bus having a host of bus
commands for synchronization and up to one megabyte data transfer rate.
Use standard IEEE-488, 26 AWG GPIB cable up to 3 metres in length.
GPIB Pin Description
The GPIB port is a special GPIB female connector. See Figure 1-1.
GPIB Connector
J2
J4
J3
100-240 Vac
47-63 Hz, 11.5-6A
MADE IN CANADA
J1
SN
J5
J6
Figure 1-1 GPIB Connector and Pins
1-2
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
Table 1-1 identifies the pin name and describes the pin functions.
Table 1-1 GPIB Pin Description (J2)
Pin # Name
Function
Note
1
DIO1
DIO2
DIO3
DIO4
EOI
DAV
NRFD
NDAC
IFC
SRQ
ATN
-
DIO1
Data
2
DIO2
Data
3
DIO3
Data
4
DIO4
Data
5
End of Identify
Data Valid
Not Ready for Data
No Data Accepted
Interface Clear
Service Request
Attention
Control
Handshake
Handshake
Handshake
Control
Control
Control
Chassis
Data
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Shield
DIO5
DIO6
DIO7
DIO8
REN
-
DIO5
DIO6
Data
DIO7
Data
DIO8
Data
Remote Enable
DAV Return
NRFD Return
NDAC Return
IFC Return
SRQ Return
ATN Return
Signal Ground
Control
Chassis
Chassis
Chassis
Chassis
Chassis
Chassis
Chassis
-
-
-
-
-
-
M370078-06
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
GPIB
Communication with Your Device
This section provides information on selecting the GPIB interface as the
communication port used on the XG, and it also provides an example of
how commands can be sent and received. The details of the IEEE 488.2
and SCPI status reporting register structures and a complete list of
commands available can be found in the XG 850 Watt Series
Programmable DC Power Supply Operating Manual (M370046-01).
Selecting a Communication Port
To select the GPIB as the communication port:
1. Turn the 9-position Mode control to PGM.
rE is displayed in the output voltage display.
2. Turn the rotary Adjust/Enter control to select the 6PIb
communication port.
3. Press the rotary Adjust/Enter control.
ADDR is displayed on the output voltage display.
4. Turn the rotary Adjust/Enter control to select the desired address
between 1 to 30. For the purpose of this example, 10 will be selected.
5. Press the rotary Adjust/Enter control to commit the new address.
6. Click Scan For Instruments on the GPIB Explorer toolbar. See
Figure 1-2.
The power supply will be found as shown in Figure 1-2.
Important: This section uses the National Instruments™ MAX program to
communicate with the XG. This is for demonstration purposes only. Any
software that is capable of addressing a GPIB device and sending and receive
text could be used in its place. Consult your GPIB card manufacturer to see if
they provide an equivalent program.
1-4
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Communication with Your Device
9. In the Send String box, enter *IDN?and click Query.
Important: If you press Enter while typing the string to be sent, the NI-488.2
Communicator program will exit.
10. The String Received window will show the ID string for the XG.
The ID string indicates the model, serial number, firmware version as
well as the GPIB card firmware version. This will be shown in the
text box below String Received. See Figure 1-4.
M370078-06
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
1-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Overview
This chapter is intended for network administrators responsible for the
configuration and maintenance of devices on the network. This chapter
provides information for connecting and configuring the power supply to
Ethernet.
Basic Section
This section describes the equipment and procedures to fully set up the
simplest configuration of an XG unit with the ENET option and a single
computer.
Important: The information in this section is applicable to the “Advanced
Section” on page 2–26. Xantrex recommends that you read through this section
even if the configuration doesn't match your final setup.
System Requirements
•
Windows XP, Windows 2000, Windows NT4.0 (with service pack
6.0a or later), Windows ME, or Windows 98
Internet Explorer 5.01 or later
30 MB hard drive space
•
•
•
64 MB RAM
Accessories
•
•
Power supply with ENET port
ENET RJ-45 and RJ-45 STP, Cat 5 cross-cable 9.84 feet (3 m) in
length or longer⑧
•
•
PC
Communication Cable
Use a standard RJ-45 (see Figure 2-1) and RJ-45 cross-cable (see
Figure 2-2).
Figure 2-1 Computer or HUB Plug
2-2
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Section
Figure 2-2 Power Supply Plug
Figure 2-3 RJ-45 Plug
Table 2-1 Description of PIN on RJ-45 Plug
Pin#
Name
TX+
TX–
RX+
Gnd
Description
Transmit data +
Transmit data –
Receive data +
Ground
1
2
3
4
5
6
7
8
Gnd
Ground
RX–
Gnd
Receive data –
Ground
Gnd
Ground
TX+
TX-
RX+
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
RX-
Figure 2-4 Scheme of ENET Cross-Cable
M370078-06
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
ENET Connector
The XPort® ENET connector is located on the rear panel of the power
supply. See Figure 2-5.
Right LED
Contact 1
Left LED
Contact 8
XPort™ ENET connector
XPort™ LEDs
The device contains two bi-color LEDs built into the front of the XPort™
connector. See Figure 2-5.
Table 2-2 Description of LEDs
LED
Color
Off
Description
No link
Link LED (Left side)
Amber
Green
Off
10 Mbps
100 Mbps
No activity
Half-duplex
Full-duplex
Activity LED (Right
side)
Amber
Green
2-4
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Section
Network Topology and Connection
The following section describes the network topology for the single
computer and single XG power supply unit. The other possible network
topologies will be discussed later in the “Advanced Section” on page 2–
26. The additional topologies build on the configuration ideas present in
this section by referencing the various setup instructions.
Single Computer and Single Power Supply Unit
Computer through a crossover cable; however, a HUB could also be used
with straight through Ethernet cables as well. Connect your computer to
the ENET as shown in Figure 2-6, or if this topology does not match your
configuration, refer to the “Advanced Section” on page 2–26 to identify
the topology you wish to implement and follow the instructions described
in that section.
Local Computer
ENET
Power Supply
Figure 2-6 Single Computer, Single Power Supply
M370078-06
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Setting Up the Computer
To set up the computer:
1. Open Explorer on the main computer, go to Control Panel >
Network Connections > Local Area connections. See Figure 2-7.
o
2. Right click on the mouse button and click on Properties.
The Local Area Connection Properties window appears. See
Figure 2-8.
2-6
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Figure 2-9 Internet Protocol (TCP/IP) Properties Dialog Box
4. Click on Use the following IP address option and type the
appropriate IP address in the box, or select the Obtain an IP address
automatically setting if your network is configured using DHCP.
5. Click OK.
2-8
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Section
Software Installations
To set up the ENET option card, the Lantronix® DeviceInstaller program
needs to be installed on your PC. DeviceInstaller is an all-in-one utility
for setting up various Lantronix devices on a network. Device Installer
auto detects any devices on the network and allows for configuration of
network settings. As a management tool, the DeviceInstaller allows for
device monitoring and status verification of the ENET option card.
To install the DeviceInstaller:
1. Insert the DeviceInstaller CD into the CD ROM drive.
If you need to manually launch the CD, click the Start button on the
Task Bar and select Run. Enter the CD drive letter, for example,
D:\Launch.exe. The DeviceInstaller Setup Wizard opens to guide the
installation process. See Figure 2-10.
Figure 2-10 DeviceInstaller Setup Wizard
2. Click Next to open the Select Installation Folder window.
The Select Installation Folder window prompts for a destination
folder for the installation.
M370078-06
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Device Using DeviceInstaller
Configuring the Device Using DeviceInstaller
The DeviceInstaller displays a list of the XG units with the ENET option
that are on the network. When the DeviceInstaller initially starts, the
device list is empty. Devices may be added by performing a search for the
devices on the network or by adding them manually.
Selecting a Network Adapter
After the installation of DeviceInstaller to your PC, you must select which
network adaptor you wish the DeviceInstaller to use for all its network
communications.
To select the network adaptor:
> DeviceInstaller > DeviceInstaller.
and there are more than one network adaptors on the PC, you might
be prompted to select the network adaptor as seen in Figure 2-12. If
this prompt does not appear, click Tools > Options... to bring up the
Options window shown in Figure 2-13.
3. Verify that the network adaptor that is connected to the network that
you are running your XG unit (s) on, is selected.
Important: Only network adaptors that are enabled and have an Ethernet
cable connected will be shown in this list. If one of your networks adaptors is not
shown in this list, verify that it is enabled and has a network cable connected to it.
4. Click the OK button.
Figure 2-12 Multiple Network Adapters
M370078-06
2-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Figure 2-13 Selecting Network Adapter
Assigning an IP Address to the Power Supply Unit
If your system is auto-IP configured, the following warning message is
displayed:
Figure 2-14 Auto-IP Address Message
Important: Auto-IP mode is acceptable only for the single computer and
single power supply configuration.
To assign an IP address to the power supply unit:
1. Click OK to dismiss the Auto-IP warning message. If you are not
intending on using an Auto-IP, debug your network connection at this
time.
The Lantronix DeviceInstaller window appears. See Figure 2-15.
2-12
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Device Using DeviceInstaller
2. Click Search to get a list of all the XG devices that can be reached
from the network adaptor that you previously selected. If your XG
unit (s) are powered up, they should appear in this list.
Figure 2-15 Searching for Power Supply IP Address
After a short delay, your power supply will be found. See
Figure 2-15. If the power supply is not found or the found device is
not reachable, contact your network administrator for details about
network settings.
3. If the IP address shown and the method that the XG unit is using to
obtain this address is correct, stop here and exit/close this window.
Otherwise, continue to step 4.
4. Expand the Local Area Connection tree; if necessary, expand further
until the IP address of the XG unit is displayed. Then left click the IP
address; the screen should display as shown in Figure 2-16.
M370078-06
2-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Figure 2-16 IP Address Details Window
window. The IP address is assigned using Steps 5 through 9 that follow.
5. In this window, click the Web Configuration tab, which will open a
new window. See Figure 2-17.
2-14
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Device Using DeviceInstaller
Figure 2-17 Entering the Lantronix Interface
6. Next to the Address field, click the green Go button.
7. You will be prompted for user name and password: ignore these
fields (leave blank) and click OK This brings up the Lantronix
.
XPort® interface (Figure 2-18).
M370078-06
2-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Configuring the Device Using DeviceInstaller
Figure 2-19 Assigning IP Settings
9. In the IP Configuration section, click the radio button next to “Use the
following IP configuration.”
Important: If you are working within a network system, please contact the
network administrator for the appropriate information to complete the IP
Address, Subnet Mask and Default Gateway fields
10. Click OK at the bottom of the page to complete the task.
11. Repeat this procedure for every power supply. Every device must
have a unique fixed IP address.
Selecting ENET as the Communication Port
Once the XG unit with the ENET option has the option card configured,
you’ll need to configure the XG to use the ENET option card as the active
communication port.
To select ENET as the communication port:
1. Turn the 9-position Mode control to PGM.
rE is displayed in the output voltage display.
M370078-06
2-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
2. Turn the rotary Adjust/Enter control to select the LAn communication
port.
3. Press the rotary Adjust/Enter control.
ADDR is displayed on the output voltage display.
4. Turn the rotary Adjust/Enter control to select the desired address
between 1 to 30.
5. Press the rotary Adjust/Enter control to commit the new address.
2-18
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal Configuration
The terminal program allows for communication with the power supply.
To use a terminal program, set it up using the parameters from the
following sections. If you wish to use HyperTerminal, see “Setting Up a
HyperTerminal Connection” for instructions.
Data Format
Serial data format is 8 bit, one stop bit. No parity bit. Flow control: none.
End of Message
The end of message is the Carriage Return character (ASCII 13,
0x0D).The power supply ignores the Line Feed (ASCII 10, 0x0A)
character.
Setting Up a HyperTerminal Connection
To set up a HyperTerminal connection:
1. Start Windows HyperTerminal by clicking Start >All Program
>Accessories > Communications > HyperTerminal.
See Figure 2-20.
Figure 2-20 HyperTerminal Connection
M370078-06
2-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
2. Click New to create a new connection.
The Connection Description window appears. See Figure 2-21.
Figure 2-21 Connection Description Window
3. Enter the name of the connection and select the icon.
4. Click OK.
The new connection setup dialog box will appear. See Figure 2-22.
Figure 2-22 New Connection Dialog Box
2-20
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
5. In the Connect using: box, select “TCP/IP (Winsock)”.
6. In the Host address box, enter the IP address, obtained in step 14 of
the section entitled “Assigning an IP Address to the Power Supply
Unit” on page 2–12.
7. In the Port number box, enter “10001” as the value.
8. Click OK.
To specify the terminal connection properties:
1. Click Disconnect if necessary, and click Properties in the main
HyperTerminal window. See Figure 2-23.
Figure 2-23 Main Terminal Window
2. In the ENET Properties window, click on XGthe Settings tab. See
Figure 2-24.
M370078-06
2-21
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal Configuration
3. Click the ASCII Setup button.
The ASCII Setup dialog box will appear as shown in Figure 2-26.
4. Verify that the ASCII Sending and ASCII Receiving boxes are
checked as shown in Figure 2-26.
Figure 2-26 ASCII Setup Dialog Box
5. Click OK.
Establishing Communication with the Power Supply
To establish communication with the power supply:
2. To verify that the XG unit is connected and functioning, type the
following command "*ADR <#>;*IDN?" where the <#>should
be replaced by the address assigned to the power supply in the
“Selecting ENET as the Communication Port” on page 2–17.
3. Verify that the XG unit responds with the ID string.
4. To save your session for future use, click File > Save As….
See Figure 2-28.
M370078-06
2-23
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal Configuration
5. Type the name of the session. It is recommended that you include the
IP in your naming convention so that it is clear which XG you are
connecting to.
6. Click Save.
Figure 2-29 Saved Session
Congratulations! Your network is installed and functioning properly.
M370078-06
2-25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Advanced Section
The advanced section describes the setup and connection for various
network topologies involving multiple power supplies.
Network Topology 1: Simple LAN
The simple LAN topology is the most common configuration for setting
up the ENET option on the XG. The topology follows the typical star
topology provided by a HUB and multiple XGs with the ENET option
and one or more computers. Figure 2-30 shows this configuration.
Local Computer #1
Local Computer #2
HUB
ENET
Power Supply #1
ENET
Power Supply #30
ENET
Power Supply #2
Figure 2-30 Multiple Power Supplies and Two Computers
All devices connects via the HUB. Every device must have a unique IP
address, for example:
•
•
•
•
•
•
Computer #1: 169.254.117.231
Computer #2: 169.254.117.232
Power supply #1: 169.254.117.220
Power supply #2: 169.254.117.221
Power supply #3: 169.254.117.222
Power supply #30: 169.254.117.230.
You must set up every device manually.
2-26
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Section
To set up for multiple power supplies and two computers:
system.
configure the XG unit (s) with. See the instructions for “Software
Installations” on page 2–9.
for “Configuring the Device Using DeviceInstaller” on page 2–11
4. Create terminal connections for each of the XG unit (s) with the
ENET option that were configured in step 3. See the instructions for
“Terminal Configuration” on page 2–19.
5. If more than one computer is going to be used, copy the filename.ht
files saved in step 3 to a disk and copy them over to each computer
that you will be using to access the XG unit (s) over the Ethernet. If
copying the files is not possible, repeat step 3 for each computer that
you wish to use.
The configuration is complete. You are now ready to use your system.
Controlling Your System
For every connected XG unit, create a separate terminal session. This
Communication with the Power Supply” on page 2–23. Also, open a
separate HyperTerminal session for each XG unit that you wish to
control. An example of two XG units in a system is shown in
Figure 2-31.
M370078-06
2-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Section
Figure 2-32 System with Two Connected Devices
Figure 2-32 shows a system with two connected devices.
Important: In this system configuration, every power supply needs a unique
IP address, whereas the address defined from front panel (power supply’s own
address) may be arbitrary.
M370078-06
2-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
Network Topology 2: ENET and RS-485 Bus
Up to 30 units may be connected to the RS-485 bus. The first unit
connects to the controller via ENET, and the other units are connected
with the RS-485 bus.
Figure 2-33 shows the system of an XG unit with the ENET option and
have its own address, defined from the front panel. Only one IP address is
required for your network (excluding computers) and only one controlling
program is required (one per XG with ENET option as noted in “Network
Topology 1: Simple LAN” on page 2–26).
Local Computer
ENET
RS-485
RS-485
IN
OUT
IN
OUT
IN
OUT
Power Supply #30
Power Supply #1
Power Supply #2
Figure 2-33 ENET and RS-485 Bus
2-30
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Section
Figure 2-34 HyperTerminal Window
Figure 2-34 shows the HyperTerminal session for the combined
configuration which is an ENET and RS-485 network. This figure also
shows access to power supplies #2 and #10 sequentially.
Setting Up Your System
1. Connect your system as shown in Figure 2-33, and turn every power
supply unit to ON.
page 2–6. Repeat this section for each computer hooked up to the
system.
Installations” on page 2–9.
4. Configure the ENET card of the master XG (power supply #1 in
Figure 2-33). See the instructions for “Configuring the Device Using
DeviceInstaller” on page 2–11.
M370078-06
2-31
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Configure the master power supply which is the unit with the ENET
option (power supply #1 in Figure 2-33) by following the
instructions in “Selecting ENET as the Communication Port” on
page 2–17.
6. The following Steps 7, 8 and 9 must be repeated for each slave unit.
7. For the slave unit that you are setting up, turn the 9-Position Mode
Control Knob to PGM.
rE is displayed in the output voltage display.
8. Turn the rotary Adjust/Enter control to select SLA and press the
rotary Adjust/Enter control.
9. Set a unique address and press the rotary Adjust/Enter control. See
the XG 850 Watt Series Programmable DC Power Supply
Operating Manual (Part number: M370078-01), Chapter 5,
proceed with the next step.
described in “Assigning an IP Address to the Power Supply Unit”
on page 2–12.
11. Create and set up a new HyperTerminal session as described in
“Terminal Configuration” on page 2–19.
12. In the HyperTerminal session window, type the *ADR
<#>;*IDN?command where the <#> should be replaced by the
address assigned to the power supply in step 9. Press enter to send
the command.
13. Verify that the unit responds with the ID string. Perform this test for
each unit that is connected including the master unit.
14. If additional XG units are using Network Topology 2, repeat the
setup procedure steps 1 to 14 for each ENET and RS-485 group.
Important: The IP address for each ENET and RS-485 group must be unique,
but the RS-485 bus addresses can be reused for each unique ENET – RS-485
group.
2-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Section
M370078-06
2-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Ethernet (ENET)
2-34
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
This section describes specific troubleshooting for the combined
ENET – RS-485 communication only.
See “Troubleshooting for ENET Communication” on page A–3 for
typical troubleshooting procedures for connecting and setting up ENET
communications.
Table A-1 Troubleshooting for ENET – RS-485 Communication
Symptom
Check
Action
One of the power supply units
is not responding.
The power supply is not turned
on.
Turn the power supply ON.
The communication interface is
Check that the RS-485 bus is
not set as a slave unit (RS-485) or selected as the communication
the address has not been set
correctly.
interface and the address is
correct.
Sequentially several units are RS-485 communication is
Check your RS-485
not responding, e.g. from #21 disconnected at the first unit that communication. Try switching the
to end.
is not responding.
cable linking this unit to the last
unit that is known to have given a
response.
All of the units are not
responding.
The ENET communication is
disconnected.
Check the ENET communication.
The HyperTerminal session is not Check the settings of the
configured properly.
HyperTerminal session. Follow
the instructions in the “Selecting
ENET as the Communication
Port” on page 2–17.
A-2
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting for ENET Communication
This section describes typical troubleshooting for connecting and setting up
the ENET communication.
Table A-2 Troubleshooting for ENET Communication
Symptom
Check
Action
DeviceInstaller does not
detect your device.
Your ENET cable is not a cross
cable.
Use the correct ENET cross cable.
Power supply is not turned on.
Turn the power supply ON.
The network that your computer is Connect a laptop to the HUB or to
on cannot reach the network that
the XG with the ENET option is
connected to.
the switch that the XG with the
ENET option is connected to, and
ping the computer you are trying
to use DeviceInstaller on. If no
response is seen, then contact your
network administrator and find
out if ICMP requests are being
filtered on the network and a
possible reason for not being able
to contact the computer.
DeviceInstaller is not configured to See “Selecting a Network
use the Ethernet card on your
computer that is connected to the
network which has the XG with
ENET option on it.
Adapter” on page 2–11.
Found device is not
reachable.
Your network is not configured
properly.
Contact your network
administrator.
Typed text is not visible.
Echo mode is not active.
Select Echo typed characters
locally in the ASCII Setup dialog
box of HyperTerminal.
M370078-06
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table A-2 Troubleshooting for ENET Communication
The power supply is not
responding.
The communication port on the
power supply unit is not selected
properly.
Select “ENET” as the
communication port.
Refer to the correct power supply
address using the front panel.
The address of the power supply
unit is not valid. The address has
not been selected using the *ADR
<address>.
See the XG 850 Watt Series
Programmable DC Power Supply
Operating Manual (Part number:
M370078-01), Chapter 5: Remote
Interface Addressing for a detailed
explanation on how to use the
*ADR command.
A-4
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Product Information
Warranty
What does this warranty cover? This Limited Warranty is provided by Xantrex Technology Inc.
("Xantrex") and covers defects in workmanship and materials in your XG 850 Watt Series
Programmable DC Power Supply. This warranty period lasts for five (5) years from the date of purchase
at the point of sale to you, the original end user customer. You require proof of purchase to make
warranty claims.
What will Xantrex do? Xantrex will, at its option, repair or replace the defective product free of
charge, provided that you notify Xantrex of the product defect within the Warranty Period, and provided
that Xantrex through inspection establishes the existence of such a defect and that it is covered by this
Limited Warranty.
Xantrex will, at its option, use new and/or reconditioned parts in performing warranty repair and
building replacement products. Xantrex reserves the right to use parts or products of original or
improved design in the repair or replacement. If Xantrex repairs or replaces a product, its warranty
continues for the remaining portion of the original Warranty Period or 90 days from the date of the
return shipment to the customer, whichever is greater. All replaced products and all parts removed from
repaired products become the property of Xantrex.
Xantrex covers both parts and labor necessary to repair the product, and return shipment to the customer
via a Xantrex-selected non-expedited surface freight within the contiguous United States and Canada.
Alaska and Hawaii are excluded. Contact Xantrex Customer Service for details on freight policy for
return shipments outside of the contiguous United States and Canada.
How do you get service? If your product requires troubleshooting or warranty service, contact your
merchant. If you are unable to contact your merchant, or the merchant is unable to provide service,
contact Xantrex directly at:
Telephone: 1 800 733 5427 (toll free North America)
1 858 450 0085(direct)
Fax:
1 858 458 0267
Email:
Web:
Direct returns may be performed according to the Xantrex Return Material Authorization Policy
described in your product manual. For some products, Xantrex maintains a network of regional
your product can be repaired at one of these facilities.
M370078-01
WA-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
What proof of purchase is required? In any warranty claim, dated proof of purchase must
accompany the product and the product must not have been disassembled or modified without prior
written authorization by Xantrex.
Proof of purchase may be in any one of the following forms:
•
•
•
The dated purchase receipt from the original purchase of the product at point of sale to the end user,
or
The dated dealer invoice or purchase receipt showing original equipment manufacturer (OEM)
status, or
The dated invoice or purchase receipt showing the product exchanged under warranty
What does this warranty not cover? This Limited Warranty does not cover normal wear and tear
of the product or costs related to the removal, installation, or troubleshooting of the customer's electrical
systems. This warranty does not apply to and Xantrex will not be responsible for any defect in or
damage to:
a) the product if it has been misused, neglected, improperly installed, physically damaged or altered,
either internally or externally, or damaged from improper use or use in an unsuitable environment;
b) the product if it has been subjected to fire, water, generalized corrosion, biological infestations, or
input voltage that creates operating conditions beyond the maximum or minimum limits listed in
the Xantrex product specifications including high input voltage from generators and lightning
strikes;
c) the product if repairs have been done to it other than by Xantrex or its authorized service centers
(hereafter "ASCs");
d) the product if it is used as a component part of a product expressly warranted by another
manufacturer;
e) the product if its original identification (trade-mark, serial number) markings have been defaced,
altered, or removed.
Disclaimer
Product
THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED BY XANTREX IN
CONNECTION WITH YOUR XANTREX PRODUCT AND IS, WHERE PERMITTED BY LAW, IN LIEU OF ALL OTHER
WARRANTIES, CONDITIONS, GUARANTEES, REPRESENTATIONS, OBLIGATIONS AND LIABILITIES, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE IN CONNECTION WITH THE PRODUCT, HOWEVER ARISING (WHETHER
BY CONTRACT, TORT, NEGLIGENCE, PRINCIPLES OF MANUFACTURER'S LIABILITY, OPERATION OF LAW,
CONDUCT, STATEMENT OR OTHERWISE), INCLUDING WITHOUT RESTRICTION ANY IMPLIED WARRANTY OR
CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO THE EXTENT REQUIRED
UNDER APPLICABLE LAW TO APPLY TO THE PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD
STIPULATED UNDER THIS LIMITED WARRANTY.
IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSSES, COSTS OR EXPENSES HOWEVER ARISING WHETHER IN CONTRACT OR TORT INCLUDING
WITHOUT RESTRICTION ANY ECONOMIC LOSSES OF ANY KIND, ANY LOSS OR DAMAGE TO PROPERTY, ANY
PERSONAL INJURY, ANY DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF MISUSE OR ABUSE, OR THE
INCORRECT INSTALLATION, INTEGRATION OR OPERATION OF THE PRODUCT.
WA-2
M370078-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
Exclusions
If this product is a consumer product, federal law does not allow an exclusion of implied warranties. To
the extent you are entitled to implied warranties under federal law, to the extent permitted by applicable
law they are limited to the duration of this Limited Warranty. Some states and provinces do not allow
limitations or exclusions on implied warranties or on the duration of an implied warranty or on the
limitation or exclusion of incidental or consequential damages, so the above limitation(s) or
exclusion(s) may not apply to you. This Limited Warranty gives you specific legal rights. You may have
other rights which may vary from state to state or province to province.
Return Material Authorization Policy
Before returning a product directly to Xantrex you must obtain a Return Material Authorization (RMA)
number and the correct factory "Ship To" address. Products must also be shipped prepaid. Product
shipments will be refused and returned at your expense if they are unauthorized, returned without an
RMA number clearly marked on the outside of the shipping box, if they are shipped collect, or if they
are shipped to the wrong location.
When you contact Xantrex to obtain service, please have your instruction manual ready for reference
and be prepared to supply:
•
•
•
•
The serial number of your product
Information about the installation and use of the unit
Information about the failure and/or reason for the return
A copy of your dated proof of purchase
Record these details in “Information About Your System” on page WA–4.
M370078-01
WA-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Return
Return Procedure
1. Package the unit safely, preferably using the original box and packing materials. Please ensure that
your product is shipped fully insured in the original packaging or equivalent. This warranty will not
apply where the product is damaged due to improper packaging.
2. Include the following:
•
The RMA number supplied by Xantrex Technology Inc. clearly marked on the outside of the
box.
•
•
•
A return address where the unit can be shipped. Post office boxes are not acceptable.
A contact telephone number where you can be reached during work hours.
A brief description of the problem.
3. Ship the unit prepaid to the address provided by your Xantrex customer service representative.
If you are returning a product from outside of the USA or Canada In addition to the above,
you MUST include return freight funds and are fully responsible for all documents, duties, tariffs, and
deposits.
If you are returning a product to a Xantrex Authorized Service Center (ASC) A Xantrex
return material authorization (RMA) number is not required. However, you must contact the ASC prior
to returning the product or presenting the unit to verify any return procedures that may apply to that
particular facility.
Out of Warranty Service
unit was damaged by misuse or incorrect installation, if other conditions of the warranty have not been
met, or if no dated proof of purchase is available, your unit may be serviced or replaced for a flat fee.
To return your XG 850 Watt Series Programmable DC Power Supply for out of warranty service,
contact Xantrex Customer Service for a Return Material Authorization (RMA) number and follow the
other steps outlined in “Return Procedure” on page WA–4.
Payment options such as credit card or money order will be explained by the Customer Service
Representative. In cases where the minimum flat fee does not apply, as with incomplete units or units
with excessive damage, an additional fee will be charged. If applicable, you will be contacted by
Customer Service once your unit has been received.
Information About Your System
As soon as you open your XG 850 Watt Series Programmable DC Power Supply package, record the
following information and be sure to keep your proof of purchase. See “Product Numbers (FGAs)” on
page iii.
_________________________________
_________________________________
_________________________________
❐ Serial Number
❐ Purchased From
❐ Purchase Date
WA-4
M370078-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Xantrex Technology Inc.
1 800 733 5427 (toll free North America)
1 858 450 0085 (direct)
1 858 458 0267 (direct)
sales@programmablepower.com
service@programmablepower.com
www.programmablepower.com
Printed in USA
M370078-06
Download from Www.Somanuals.com. All Manuals Search And Download.
|