by
XPower Powerpack
400 PLUS and 400R
by
Owner's Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Purpose
The purpose of this Owner’s Guide is to provide explanations
and procedures for installing, operating, maintaining, and
troubleshooting the XPower Powerpack 400 Plus and
XPower Powerpack 400R.
The Guide provides safety guidelines, detailed planning and
setup information, as well as information about operating and
troubleshooting the unit.
Conventions Used
The following conventions are used in this guide.
WARNING
Warnings identify conditions that could result in
personal injury or loss of life.
CAUTION
Cautions identify conditions or practices that could
result in damage to the product or to other
equipment.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Important: These notes describe an important action item
or an item that you must pay attention to.
Note: These notes describe additional information which
may add to your understanding of how to use the product.
References to XPower Powerpack
In this guide, both the XPower Powerpack 400 Plus and the
XPower Powerpack 400R (with radio and air compressor)
are referred to as XPower Powerpack when the information
applies to both models. However, when the information is
specific to one model, then reference is made specifically to
the XPower Powerpack 400 Plus or to the XPower
Powerpack 400R.
Related Information
You can find more information about Xantrex Technology
Inc. as well as its products and services at www.xantrex.com
ii
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
The XPower Powerpack 400 Plus and XPower Powerpack
400R generate a type of AC power similar to a normal
household wall outlet. Operating the XPower Powerpack
incorrectly or misusing it may damage the equipment or
create hazardous conditions for the user.
Important: Before using your XPower Powerpack 400 Plus and
XPower Powerpack 400R, be sure to read and save these safety
instructions.
Warnings and Cautions
WARNING: Shock hazard. Keep away from
children.
The XPower Powerpack generates the same potentially lethal AC
power as a normal household wall outlet. Do not insert foreign
objects into the AC Outlet, the DC Power Socket, the Jump-Start
Cable Port, or the ventilation holes. Do not expose this product to
water, rain, snow, or spray.
Do not open the XPower Powerpack except to replace the internal
battery. Have a qualified technician complete any service work.
CAUTION
Do not connect any AC appliance with the neutral conductor
connected to ground to the XPower Powerpack.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
CAUTION
Do not expose the XPower Powerpack to temperatures over 104 °F
(40 °C).
-
WARNING: Explosion hazard
Do not use this product where there are flammable fumes or gases,
such as in the bilge of a gasoline- powered boat, or near propane
tanks. Do not use this product in an enclosure containing
automotive-type lead acid batteries. These batteries, unlike the
sealed AGM battery in XPower Powerpack, vent explosive
hydrogen gas which can be ignited by sparks from electrical
connections.
When working on electrical equipment, always ensure someone is
nearby to help you in an emergency.
WARNING: Heated surface
Ensure at least 2" (5 cm) air space is maintained on all sides of the
XPower Powerpack. During operation, keep away from materials
that may be affected by high temperatures such as blankets, pillows
and sleeping bags.
WARNING: Fire hazard
Never allow jump-start cables’ red and black clamps to touch each
other or another common metal conductor. This could cause
damage to the unit and/or create a sparking/explosion hazard.
Always disconnect the jump-start cables from the unit after use and
clip the plastic guard over the jump-start cable port.
WARNING: Fire hazard
Jump-start cable clamps must be connected positive to positive (red
clamp to battery “+”) and negative to negative (black clamp to
battery “-”). A reverse polarity connection (positive to negative)
may cause damage to the unit and/or create a sparking/explosion
hazard.
iv
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
WARNING: Fire hazard
The jump-start feature is designed for short term operation only—
less than 4 seconds. Operating the jump-start feature for more than
4 seconds may cause damage to the unit. Allow the XPower
Powerpack to cool down for at least 3 minutes after each jump-
start.
WARNING: Risk of explosion, fire or burns
The battery terminals exposed at the Jump-Start Cable Port have
enough energy present to cause a spark, creating an explosion
hazard, or to cause burns if a metal object contacts both terminals.
Always clip the plastic guard over the Port when not in use.
WARNING: Fire hazard
Do not leave the compressor unattended while operating. The
compressor is designed for short term operation only. Operation of
the compressor over an extended period of time will cause the
compressor unit to overheat and may cause damage. Allow the
compressor to cool down for 10 minutes after each 10 minutes of
continuous operation.
975-0162-01-01
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Precautions When Working With Batteries
WARNING: Explosion and fire hazard
1. Follow all instructions published by the battery
manufacturer and the manufacturer of the equipment in
which the battery is installed.
2. Make sure the area around the battery is well-ventilated.
3. Never smoke or allow a spark or flame in vicinity of the
engine or batteries.
4. Be careful not to drop a metal object on the battery or
allow a metal tool to simultaneously touch the positive
and negative cable ends or battery terminals. It might
spark or short-circuit the battery or other electrical parts
and cause an explosion.
5. Remove personal metal items such as rings, bracelets,
necklaces, and watches when working with a lead-acid
battery. A lead-acid battery produces a short-circuit
current high enough to weld a ring or other similar
objects to metal, causing a severe burn.
6. If you need to remove a battery, always remove the
positive terminal from the battery first. Make sure all
accessories are off so you don’t cause an arc.
7. Someone should be within range of your voice, or close
enough to come to your aid when you work near a lead-
acid battery.
8. Have plenty of fresh water and soap nearby in case
battery acid contacts skin, clothing, and eyes.
9. Wear complete eye protection and clothing protection.
Avoid touching your eyes while working near batteries.
vi
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
10. If battery acid contacts skin or clothing, wash
immediately with soap and water. If acid enters your
eyes, immediately flood them with running cold water for
at least twenty minutes and get medical attention
immediately.
11. Keep a supply of baking soda on hand in the area of the
batteries. Baking soda neutralizes lead-acid battery
electrolyte.
975-0162-01-01
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Precautions for Using Rechargeable
Appliances
CAUTION
The output of the inverter is non-sinusoidal.
Most rechargeable battery-operated equipment uses a
separate charger or transformer that is plugged into an AC
receptacle and produces a low voltage charging output.
Some chargers for rechargeable batteries can be damaged if
connected to the XPower Powerpack 400 Plus and XPower
Powerpack 400R.
Do not use the following with the XPower Powerpack 400
Plus and XPower Powerpack 400R:
•
Small battery-operated appliances like flashlights, razors,
and night lights that can be plugged directly into an AC
receptacle to recharge.
•
Some chargers for battery packs used in hand power
tools. These affected chargers display a warning label
stating that dangerous voltages are present at the battery
terminals.
Note: If you are unsure about using your rechargeable appliance
with the XPower Powerpack, contact the equipment manufacturer
to determine the rechargeable appliance’s compatibility with the
modified sine wave (non-sinusoidal) AC waveform.
viii
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Important Safety Instructions
Warnings and Cautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - iii
Precautions When Working With Batteries- - - - - - - - - - - - - - - vi
Precautions for Using Rechargeable Appliances - - - - - - - - - - viii
1
2
Introduction
About the XPower Powerpack - - - - - - - - - - - - - - - - - - - - - - 1–1
Comprehensive Protection - - - - - - - - - - - - - - - - - - - - - - - - - 1–1
Automatic overload- - - - - - - - - - - - - - - - - - - - - - - - - - - 1–1
Overheating - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 1–2
Low Battery Protection - - - - - - - - - - - - - - - - - - - - - - - - 1–2
Jump-Start Cables Safety Feature - - - - - - - - - - - - - - - - - 1–2
Features
Materials List - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–1
XPower Powerpack Features - - - - - - - - - - - - - - - - - - - - - - - 2–2
Front Panel Detail- - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–2
Rear Panel Detail (XPower Powerpack 400R only) - - - - - 2–5
Air Compressor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–7
Left Side View - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2–8
Storage Compartment - - - - - - - - - - - - - - - - - - - - - - - - - 2–9
Accessories - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -2–10
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Operation
Operating Conditions and Guidelines - - - - - - - - - - - - - - - - - 3–1
Choosing a Location - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–2
Using XPower Powerpack for the First Time - - - - - - - - - - - - 3–3
Recharging with the AC Charger - - - - - - - - - - - - - - - - - - - - 3–3
Using the light - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3–4
Operating AC Appliances - - - - - - - - - - - - - - - - - - - - - - - - - 3–4
Understanding AC Appliances - - - - - - - - - - - - - - - - - - - 3–4
Run Time on Typical AC Appliances - - - - - - - - - - - 3–5
High Surge Appliances - - - - - - - - - - - - - - - - - - - - - 3–5
Trouble Appliances - - - - - - - - - - - - - - - - - - - - - - - 3–6
Operating Several Appliances at Once - - - - - - - - - - - 3–6
Operating an AC Appliance - - - - - - - - - - - - - - - - - - - - - 3–6
Operating 12 V DC Appliances - - - - - - - - - - - - - - - - - - - - - 3–8
Jump-Starting a Vehicle’s Engine - - - - - - - - - - - - - - - - - - - -3–10
Using the Air Compressor - - - - - - - - - - - - - - - - - - - - - - - - -3–12
Over-Temperature Safety Protection - - - - - - - - - - - - - - -3–12
Inflating Tires - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3–13
Inflating Small Sports Equipment - - - - - - - - - - - - - - - - -3–14
Using the Radio: XPower Powerpack 400R - - - - - - - - - - - - -3–15
Power Draw- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -3–16
Listening to the AM Band - - - - - - - - - - - - - - - - - - - - - -3–16
Connecting to an External Battery- - - - - - - - - - - - - - - - - - - -3–16
4
Maintenance
Battery Maintenance - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–1
Recharging the XPower Powerpack Battery - - - - - - - - - - - - - 4–2
Recharging with the AC Charger- - - - - - - - - - - - - - - - - - 4–2
Recharging with the DC Charging Cable - - - - - - - - - - - - 4–3
Recharging with a Generator’s Regulated 12 V DC Outlet 4–5
Recharging From a Solar Panel- - - - - - - - - - - - - - - - - - - 4–6
Replacing the Internal Battery - - - - - - - - - - - - - - - - - - - - - - 4–6
Battery Life - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4–6
x
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Obtaining a Replacement Battery - - - - - - - - - - - - - - - - - 4–7
Replacing the Battery - - - - - - - - - - - - - - - - - - - - - - - - - 4–7
Replacing the Incandescent Light - - - - - - - - - - - - - - - - - - - - 4–9
Replacing the External Fuse- - - - - - - - - - - - - - - - - - - - - - - -4–10
5
Troubleshooting
Common Problems - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–1
Buzz in Audio Equipment - - - - - - - - - - - - - - - - - - - - - - 5–1
Television Interference - - - - - - - - - - - - - - - - - - - - - - - - 5–1
Troubleshooting Reference - - - - - - - - - - - - - - - - - - - - - - - - 5–2
A
B
Specifications
Electrical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - A–1
Physical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - A–3
Warranty and Product Information
Warranty- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - B–2
Return Material Authorization Policy - - - - - - - - - - - - - - - - - B–5
Out of Warranty Service - - - - - - - - - - - - - - - - - - - - - - - - - - B–7
Information About Your System- - - - - - - - - - - - - - - - - - - - - B–8
975-0162-01-01
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
About the XPower Powerpack
Easy-to-use and designed for years of reliable service, the
XPower Powerpack can run many AC appliances and 12 V
DC appliances whenever you need power for work or play, at
home or on the road.
XPower Powerpack:
•
•
•
•
•
Powers 115 V AC appliances
Powers 12 V DC appliances
Jump-starts vehicle engines
Provides lighting for emergency use
Inflates tires and small sports equipment with a 250 psi
air compressor.
In addition, the XPower Powerpack 400R comes with:
An AM/FM radio with digital alarm clock.
•
Comprehensive Protection
Automatic overload
The XPower Powerpack has built-in protection against output
overload. If you connect to the AC Outlet(s) an appliance that
draws more than 320 W, or one which draws excessive surge
power, the power to the AC Outlet automatically shuts off.
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Overheating
The XPower Powerpack is protected from overheating. If the
inverter exceeds a safe temperature, power to the AC Outlet
automatically shuts off.
Low Battery Protection
Low battery protection protects the internal battery from
excessive discharge and possible damage. When the AC
Outlet ON/OFF switch is turned on, an audible alarm alerts you
when the internal battery is nearly discharged (11.0 V DC)
and the unit turns off at 10.5 V DC.
Jump-Start Cables Safety Feature
The XPower Powerpack comes with a user-replaceable
250 A fuse to protect the unit and vehicle battery from
damage through reverse polarity and short-circuit conditions.
1-2
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Features
Chapter 2 describes the main features of the XPower
Powerpack. We recommend that you familiarize yourself
with these features before operating the unit.
Materials List
Your XPower Powerpack package includes these items:
❐
XPower Powerpack 400 Plus or XPower Powerpack 400R
❐ Owner’s Guide
❐ AC charger
❐ DC charging cable
❐ Jump-start cables
❐ Accessory bag
❐ Two nozzle adaptors for the compressor
❐ One sports needle adaptor for the compressor.
The XPower Powerpack 400R also includes:
❐ Red “emergency” light cover.
If any of these materials are missing or are unsatisfactory in
any way, please contact Customer Service, see Appendix B.
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
XPower Powerpack Features
Front Panel Detail
5
6
7
4
8
3
2
1
XPower Powerpack Features
Feature
Description
1
DC Power Socket can:
• Power 12 V DC auto, RV or marine appliances
• Recharge XPower Powerpack from a 12 V
outlet in a vehicle using the DC Charging Cable.
2
3
4
2 AC Outlets are standard 3-prong outlets supplying
120 V AC power for running an AC appliance.
AC Outlet ON/OFF switch illuminates when the
switch is turned on.
Digital Display displays the inverter’s Output
Power in W and Battery Charge status in
% FULL.
2-2
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
XPower Powerpack Features
Feature
Description
5
Charging Status light illuminates when the
XPower Powerpack is in Charging Status mode
(i.e. AC Charger is connected to the inverter’s
Charger Input Socket and plugged into the
household 120 V AC outlet).
6
7
8
Battery Charge % light illuminates (green) when
Battery Charge information is displayed on the
Digital Display.
Output Power (W) light illuminates (green) when
Output Power information is displayed on the
Digital Display.
Display Function button, when pressed, allows for
reading Battery Charge status on the Digital
Display. Toggles Digital Display’s power ON/OFF.
Not
Audible Alarm (inside the unit) sounds in the event
shown
of overheating or low battery protection on inverter.
Control Panel Operation
Required
How to...
Condition
Required Action Note
Monitor total
AC power
consumed by
the
Inverter’s ON/OFF
switch is turned ON;
Output Power (W)
light illuminates
(green);
No action required.
The Digital Display
will show the AC
power drawn from the run time, press Display
inverter by the Function button to turn
In order to save the
battery power and
ensure longer inverter
applications
powered from AC charger is
applications powered off the Digital Display.
the
unplugged from the
from the Powerpack’s PressDisplay Function
Powerpack’s 2 wall AC outlet.
AC outlets
AC outlets.
button again to turn the
display on for AC
power reading.
975-0162-01-01
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Required
Condition
How to...
Required Action Note
Monitor
Battery
Charging
status
Inverter’s ON/OFF
switch is turned to
OFF;
No action required.
Recharging with the
supplied AC charger is
a true “plug-in-and-
forget” charging
A flashing green
All appliances must be Charging Status
disconnected from the light indicates that the method.
AC and DC power
outlets;
Powerpack’s battery
needs recharging and the AC charger
We recommend leaving
The ON/OFF switch of that the AC charger is connected when the
the incandescent light charging the battery.
must be turned to OFF;
Powerpack is not in use
to permanently
The AC charger must A steady green
maintain the battery in
fully charged condition.
be plugged into the
Charging Status
Powerpack’s Charger light indicates that the
Input Socket and also Powerpack’s battery
in to a household AC
outlet.
is fully charged and
the Powerpack is
ready for use.
Check Battery Inverter’s ON/OFF
Push and hold the
Display Function
button.
This function is
Charge status
switch is turned to
OFF;
disabled when the AC
charger is plugged in to
the Charger Input
All appliances must be
disconnected from the The green Battery
Socket, or when the
AC and DC power
outlets;
Charge (%) light will inverter main switch is
come on and the
ON.
The ON/OFF switch of Digital Display will
the incandescent light show the remaining
For accurate Battery
Charge reading, allow
must be turned to OFF; battery capacity in %. 15 minutes between
The AC charger must
not be plugged into
the Powerpack’s
charging/use and
battery capacity check.
Charger Input Socket.
2-4
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
XPower Powerpack Features
Rear Panel Detail (XPower Powerpack 400R only)
1
2
3
4
5
6
7
8
12
9
11
10
Feature Description
1
2
FM antenna
Frequency indicator light
Power OFF button
Time set button
3
4
5
Tuning dial
6
Hours set button
7
Minutes set button
Volume dial
8
9
Alarm set button
Alarm clock ON/OFF button
AM band button/ON
FM band button/ON
10
11
12
975-0162-01-01
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Radio Operation
Required
How to... Condition Required Action
Note
Listen to
the radio
Press the AM band button
(11) or the FM band button station frequency is
When radio is on, the
(12).
displayed. When
radio is off, the time is
displayed.
To turn off the radio, press
the power OFF button (3).
Set the
clock
Turn off the To adjust hour, press and
The clock uses a 12-
hour (AM/PM) time
format.
radio to
show the
time.
hold Time Set button (4),
and press hours set button
(6).
To adjust minutes, press and
hold (4), and press minutes
set button (7).
Set the
alarm
Turn off the To adjust hour, press and
The alarm clock uses
a 12-hour (AM/PM)
time format.
radio to
show the
time.
hold Alarm Set button (9),
and press hours set button
(6).
To adjust minutes, press and
hold (9), and press minutes
set button (7).
Use the
Set the
Press Alarm Clock ON/OFF
When the alarm clock
turns the radio on, the
power off button (3)
does not work. To
turn off the radio,
press Alarm Clock
ON/OFF (10), then
press (3).
alarm clock alarm, turn button (10). “¤” shows on
off radio to the display screen.
show time.
Improve
reception
Radio
tuned to
FM station.
Adjust the direction and
length of the FM antenna.
N/A.
2-6
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
XPower Powerpack Features
Air Compressor
2
1
3
Feature Description
1
2
ON/OFF switch turns the compressor unit on and off.
Pressure gauge shows the PSI (lb./in2)
3
Valve connector with connector hose
Nozzle Adaptor Compartment is integrated into AC charger
compartment.
975-0162-01-01
2-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Left Side View
1
2
3
4
Feature Description
1
2
3
5 W incandescent light illuminates for about 30
hours when the battery is fully charged.
Light ON/OFF Switch (400 Plus)
Light ON/OFF/Pulse Switch (400R)
Jump-Start Cable Port supplies high power DC
current. The cables connect to the Jump-Start Cable
Port when jump-starting a vehicle’s battery or when
connecting an external battery to the XPower
Powerpack. The jump-start cable connection is
designed so that the cables cannot be inserted
incorrectly into the Jump-Start Cable Port.
4
Plastic Guard for covering Jump-Start Cable Port.
2-8
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
XPower Powerpack Features
Storage Compartment
3
4
5
2
1
6
XPower Powerpack 400R shown
Feature Description
1
AC Charger lets you recharge the XPower
Powerpack from a standard AC wall outlet and can
only be used to recharge the internal battery of the
XPower Powerpack. Can be stored in AC charger
compartment.
2
3
Charger Input Socket for use with the AC Charger
supplied (see 1).
External Replaceable Fuse is rated at 250 A, 32 V.
Located behind fuse cover.
4
5
6
Red “emergency” light cover
Compressor Nozzle Adaptor Compartment
AC Charger Compartment may be used for storing
the AC Charger.
975-0162-01-01
2-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Accessories
2
1
3
4
Feature Description
1
Red emergency light cover stored in the rear
compartment (400R only). This cover can turn the
5 W incandescent light into a red “emergency” light
when placed over the existing clear lens.
2
3
Detachable heavy-duty jump-start cables
DC Charging Cable lets you recharge the XPower
Powerpack from a 12 V system in a car, SUV, RV or a
boat. This can be stored in the storage compartment.
4
Accessory bag
Not
Shown
Nozzle packet contains two nozzle adaptors and
sports needle adaptor, in the storage compartment on
the back of the unit.
2-10
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Operation
Chapter 3 explains how to operate the XPower Powerpack
efficiently. This chapter covers:
•
•
•
•
•
•
Recharging the XPower Powerpack for first time use
Using the built in light
Operating AC appliances and 12 V DC appliances
Jump-starting a vehicle’s engine
Connecting to an external battery for additional run time
Using the compressor.
Operating Conditions and Guidelines
CAUTION
Read all operating instructions before operating the XPower
Powerpack.
CAUTION
Do not use the XPower Powerpack to operate any AC appliances
or 12 V DC appliances while recharging with the AC Charger.
The AC Charger may fail if AC appliances or 12 V DC
appliances are operated while the AC Charger is connected.
CAUTION
The XPower Powerpack is not intended for use as a UPS
(Uninterruptible Power Supply).
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Choosing a Location
WARNING: Fire or explosion
The XPower Powerpack contains components that tend to produce
arcs or sparks. To prevent fire or explosion, do not operate the
XPower Powerpack in compartments containing batteries or
flammable materials, or in locations that require ignition-protected
equipment.
The XPower Powerpack should be operated only in locations
that meet these requirements:
:
Do not allow water or other liquids to drop or splash on the
XPower Powerpack.
Dry
Ambient air temperature should be between 32 and 104ºF
(0 and 40ºC)—the cooler the better within this range.
Cool
Leave at least 2" (5 cm) clearance around the XPower
Powerpack for air flow. Ensure that the ventilation openings
are not obstructed.
Ventilated
Safe
Do not operate the unit in the same compartment as
batteries or in any compartment capable of storing
flammable liquids like gasoline.
Do not operate the unit where it will be exposed to battery
gases. These gases are very corrosive, and prolonged
exposure will damage the XPower Powerpack.
Protected
frombattery
gases
3-2
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Using XPower Powerpack for the First Time
Using XPower Powerpack for the First Time
n
Important: Prior to operating your AC appliance or 12 V DC
appliance, ensure that the battery of the XPower Powerpack is
fully charged. If the battery has been fully discharged, recharging
with the AC Charger may take up to 35 hours.
Recharging with the AC Charger
Note: The Battery Charge (%) reading on the digital display is
only accurate when the XPower Powerpack has been
disconnected from all appliances and all charging sources for
fifteen minutes.
Recharging with the AC Charger is a true “plug-in-and-
forget” charging method. We recommend leaving the AC
Charger connected when the XPower Powerpack is not in
use.
To recharge with the AC Charger:
1. Disconnect any 12 V DC appliances and turn the light
off.
2. Turn the AC Outlet ON/OFF switch to OFF.
3. Plug the AC Charger into a standard AC wall outlet.
4. Insert the AC Charger cable end into the Charger Input
Socket located in the storage compartment of the unit.
The green Charging Status light changes from flashing to
steady when charging is complete (about 35 hours if the
battery is completely discharged).
Important: The 35-hour charging time for the XPower
Powerpack assumes that there is 120 V at the AC wall outlet. If
the voltage is less than 120 V AC, it may take more than 35 hours
to fully recharge the XPower Powerpack. If, after 35 hours of
charging, the green Charging Status light is still flashing,
continue to charge the unit for another 15 hours.
975-0162-01-01
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Important: If you keep the XPower Powerpack in storage, the
battery will discharge over time. Remember to recharge the
battery every three months to keep the XPower Powerpack
operational.
Note: Once fully charged, the charging current automatically
reduces to a maintenance charge mode, and the XPower
Powerpack may be left permanently connected to the AC Charger.
Using the light
The XPower Powerpack has a built-in incandescent light
which will operate for about 30 hours before the unit needs to
be recharged.
The XPower Powerpack 400 Plus has a two-position OFF/ON
switch (located beneath the light itself). The XPower
Powerpack 400R has a three-position ON/OFF/Pulse switch. In
the “Pulse” position, the light will flash on and off. The
XPower Powerpack 400R also has a red “emergency” light
cover that fits over the incandescent light for additional
signalling capability.
The light can be adjusted up and down by pushing against the
top or bottom of the rim around the lens.
Operating AC Appliances
Understanding AC Appliances
AC appliances are rated by how much electrical power (in
watts) they consume. XPower Powerpack can power most
appliances within its continuous power rating (320 W, 2.7 A).
Some appliances may be difficult or impossible to operate
from the XPower Powerpack. They may have high surge
requirements or should not be run from the XPower
Powerpack. See “High Surge Appliances” on page 3–5 and
“Trouble Appliances” on page 3–6.
3-4
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating AC Appliances
Run Time on Typical AC Appliances
Note: The fewer watts an AC appliance uses, the longer the
XPower Powerpack will operate before recharging is required.
Typical AC appliances that can be used on the XPower
Powerpack are listed in Table 3-1.
Table 3-1 AC Appliances and Run Times
Wattsa
Hoursb
AC Appliance
Cordless telephone (stand by) 5
40
Home security system
Fluorescent work light
Fireplace fan
5
40
14
20
25
40
60
190
10
8
Laptop computer
Table lamp
6
3
Color TV – 13"
3/8" drill
2 h 30 min.
20 min.
a. Represents actual power consumption as measured on sample
appliances.
b. Operating times assume a fully charged 20 Ah battery and may vary
based on model/brand of appliance.
High Surge Appliances
The wattage rating of AC appliances is the average power
used by the appliance. Appliances such as televisions,
computer monitors and appliances with motors consume
much more power than their average rating when they are
first switched on.
Although XPower Powerpack can supply momentary surge
power up to 600 W, some appliances may exceed the
capabilities of the XPower Powerpack and trigger the
inverter’s safety overload shutdown circuit.
975-0162-01-01
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Trouble Appliances
t
CAUTION
The output of the Powerpack’s inverter is non-sinusoidal.
Some equipment may be damaged by the inverter’s modified sine
wave output (non-sinusoidal).
Some appliances, including the types listed below, may be
damaged if they are connected to the inverter:
•
•
•
Electronics that modulate RF (radio frequency) signals
on the AC line will not work and may be damaged.
Speed controllers found in some fans, power tools,
kitchen appliances, and other loads may be damaged.
Some chargers for small rechargeable batteries can be
damaged. See “Precautions for Using Rechargeable
Appliances” on page viii for details.
•
Metal halide arc (MHI) lights can be damaged.
Note: If you are unsure about powering any device with the
inverter, contact the manufacturer of the device.
Operating Several Appliances at Once
You can run several AC appliances if the total rating of all the
appliances (in watts) does not exceed 320 W. You can run
appliances using an AC power bar.
Run time, however, will decrease accordingly with the
number of appliances being operated and the AC power being
consumed.
Operating an AC Appliance
Before operating your AC appliance, ensure that the battery
of the XPower Powerpack is fully charged. See “Recharging
with the AC Charger” on page 3–3 for details.
3-6
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating AC Appliances
To operate an AC appliance:
1. Open the protective covering on the right side of the
XPower Powerpack. Turn the AC Outlet ON/OFF switch
to the ON position.
The switch illuminates to indicate AC power is available
at the AC Outlets.
2. Plug the AC appliance into one of the AC Outlets and
turn the appliance on. XPower Powerpack will operate
most devices rated up to 320 W.
3. Recharge the XPower Powerpack as soon as possible
after each use.
When using the XPower Powerpack to operate an AC
appliance and the low battery warning sounds, the
warning gives you time to shut your AC appliance off
before loss of AC power.
If you ignore the warning, the XPower Powerpack
automatically turns off a few minutes later to prevent
battery damage.
In the event of an overload, low battery voltage or
overheating, the XPower Powerpack automatically shuts
down.
975-0162-01-01
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Operating 12 V DC Appliances
The XPower Powerpack can operate 12 V DC auto, RV,
marine, or other portable appliances that draw 12 A or less
from a 12 V DC power outlet or from a vehicle’s lighter
socket.
CAUTION Equipment damage
The DC Power Socket does not automatically switch off when the
internal battery is discharged. To protect the internal battery against
damage resulting from total discharge, We recommend that the AC
Outlet On/Off switch is turned On when using the XPower
Powerpack to operate a 12 V DC appliance.
Having the AC Outlet On/Off switch turned On enables the alarm
to warn you when the 12 V DC appliance has nearly depleted the
internal battery.
Note: The fewer watts a 12 V DC appliance draws, the longer
the XPower Powerpack will operate before recharging is required.
3-8
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating 12 V DC Appliances
Typical 12 V DC appliances that can be used on the XPower
Powerpack are listed in Table 3-2.
Table 3-2 12 V DC Appliances and Run Times
Wattsa
Hoursb
12 V DC Appliance
5 W incandescent light (built 5
30
into the unit)
Cellular telephonec
Portable Cooler
6
30
4
30
a. Represents actual power consumption as measured on sample
appliances.
b. Operating times assume a fully charged 20 Ah battery and may vary
based on model or brand of appliance.
c. Represents talks time available from 10 recharge cycles.
To operate a 12 V DC appliance:
1. Open the protective cover on the left side of the XPower
Powerpack.
2. Plug the 12 V DC appliance into the DC power socket on
the left side of the unit, and turn the 12 V DC appliance
on (if required).
If the 12 V DC appliance draws more than 12 A (or has a
short-circuit defect), the internal circuit breaker of the
XPower Powerpack shuts off the power to the 12 V DC
appliance. If this occurs, unplug the 12 V DC appliance,
and the internal circuit breaker automatically resets after
a few seconds.
3. Fully recharge the XPower Powerpack as soon as
possible after each use.
As the DC power socket is internally wired directly to the
internal battery, extended operation of a 12 V DC
appliance may result in excessive battery discharge. See
Caution for “Equipment damage” on page 3–8.
975-0162-01-01
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Jump-Starting a Vehicle’s Engine
You can use the XPower Powerpack to jump-start a vehicle
or boat engine that has a 12 V starting battery using the
supplied Jump-Start cables.
WARNING: Fire hazard
Never allow cables’ red and black clamps to touch each other or
another common metal conductor. This could cause damage to the
unit and/or create a sparking/explosion hazard. Always disconnect
the clamps for the unit after use and clip the plastic guard over the
jump-start cable port.
WARNING: Fire hazard
Jump-start cable clamps’ connection to the vehicle’s battery
terminals must be positive to positive (red clamp to battery “+”)
and negative to negative (black clamp to battery “-”). A reverse
polarity connection (positive to negative) may cause damage to the
unit and/or create a sparking/explosion hazard.
WARNING: Risk of explosion, fire or burns
The battery terminals exposed at the Jump-Start Cable Port have
enough energy present to cause a spark, creating an explosion
hazard, or to cause burns if a metal object contacts both terminals.
Always clip the plastic guard over the Port when not in use.
Important: Closely follow these instructions for jump-starting
your vehicle as they may be different from the instructions
supplied with other jump-start products or jump-start cables.
To jump-start a vehicle or boat engine:
1. Turn OFF the vehicle or boat ignition and all accessories.
2. Engage the park or emergency brake and place the
transmission in park for an automatic or neutral for a
manual.
3. If jump-starting a boat engine, purge the engine
compartment and bilge of all fumes before jump-starting.
3-10
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Jump-Starting a Vehicle’s Engine
4. Connect the cables to the Jump-Start Cable Port on the
left side of the XPower Powerpack.
5. Position the XPower Powerpack on a flat, stable surface
near the battery and away from all moving parts of the
engine.
6. Connect the red positive (+) clip of the cables to the
positive (+) terminal of the engine battery.
The battery’s positive terminal is usually larger in
diameter than the negative terminal. In most vehicles, the
battery’s positive terminal has a red wire connected to it.
7. Connect the black negative (–) clip of the cables to the
engine block, cylinder head, or other stationary heavy
metal part of the motor, or to the negative (–) battery
terminal.
Before starting the engine, make sure the XPower
Powerpack and the cables are clear of belts and fans. Do
not crank the engine for more than 4 seconds.
WARNING: Fire hazard
The jump-start feature is designed for short term operation only—
less than 4 seconds. Operating the jump-start feature for more than
4 seconds may cause damage to the unit. Allow the XPower
Powerpack to cool down for at least 3 minutes after each jump-
start.
8. Remove the red positive (+) clip and then the black
negative (–) clip from the vehicle’s battery terminal.
9. Remove the cables from the Jump-Start Cable Port.
Important: Recharge the XPower Powerpack as soon as
possible after each use. See “Recharging the XPower Powerpack
Battery” on page 4–2.
975-0162-01-01
3-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Using the Air Compressor
WARNING: Fire hazard
The compressor is designed for short term operation only.
Operating the compressor over an extended period of time will
cause the compressor unit to overheat, which could lead to fire.
Allow the compressor to cool down for 10 minutes after each 10
minutes of continuous operation.
WARNING: Fire hazard
Do not leave the compressor unattended while in operation. Keep
out of reach of children.
WARNING: Risk of personal injury or
damage to equipment
Never leave the compressor unattended while in operation. The
compressor is capable of inflating to 250 PSI. Do not exceed the
recommended pressure of either the compressor or the object being
inflated. If either recommended pressure is exceeded, an explosion
may result.
Over-Temperature Safety Protection
It is recommended that you follow the warnings and turn the
compressor OFF for 10 minutes after every 10 minutes of
operation. However, the XPower Powerpack is equipped with
an over-temperature safety protection feature that
automatically turns the compressor off if it begins to
overheat. Once the compressor cools down to its normal
operating temperature it will automatically turn on again and
continue inflating. You should turn the compressor off at the
power switch if this safety feature engages, and allow the
compressor to cool for 15 minutes before re-starting.
3-12
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Air Compressor
WARNING: Risk of personal injury or
damage to equipment
Never leave the compressor unattended once it has switched itself
off due to overheating. It will turn on again and continue inflating
when its internal temperature drops.
Turn the compressor OFF at the power switch after each use or any
time the compressor turns off automatically.
Inflating Tires
Table 3-3 Pressure Specifications for Common Items
Tires
PSI
26
26
30
24
Other Inflatables PSI
520-13
A-78-14
E78-14
H-78-14
Football
13
9
Basketball
Volleyball
5
Lawn Tractor Tire
22
HR-78-15
Bicycle Tires
27-1 ¼
28
85
40
20-1 ½
Note: The information in the table is for reference only. For
precise pressure specifications, refer to the information supplied
with the article to be inflated.
975-0162-01-01
3-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
CAUTION
If the pressure gauge on the compressor indicates more than twice
the recommended pressure for the object you are inflating, and you
have only started to inflate the object, the valve connector is
incorrectly connected to the valve stem. This may damage the
XPower Powerpack. Remove and reattach the valve connector to
the valve stem.
To inflate your vehicle, motorcycle, or bicycle tires:
1. Place the valve connector securely on the tire valve stem,
push it as far as possible to allow normal airflow, and
close the thumb latch. If necessary, use a supplied nozzle
adapter.
2. Turn the compressor on, and inflate your tire to the
pressure specified by its manufacturer. Use Table 3-3,
“Pressure Specifications for Common Items” on page 3–
13 as a general guide only.
3. Turn the compressor OFF after appropriate pressure is
reached.
4. Open the thumb latch and remove the valve connector
from the valve stem.
5. Check air pressure with a pressure gauge.
Note: Leave the thumb latch in the open position for storing to
relieve pressure on the internal mechanisms.
Inflating Small Sports Equipment
You can use the compressor to inflate small sports equipment
such as balls (soccer balls and footballs).
3-14
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the Radio: XPower Powerpack 400R
CAUTION
The XPower Powerpack cannot be used to inflate large capacity
inflatables such as float tubes, large air mattresses, and inflatable
boats. These types of products require extended inflating times
which may damage the compressor.
To inflate small sports equipment:
1. Place the valve connector fully on or into the valve
receptacle on the item. Go to Step 4.
OR
If necessary, use a supplied nozzle adaptor.
2. Choose the appropriate nozzle adaptor, insert the nozzle
adaptor into the valve stem and close the thumb latch.
3. Insert nozzle adaptor into the valve receptacle of the
item.
4. Turn the compressor on and inflate to appropriate
pressure.
WARNING: Fire hazard
Allow the compressor to cool down for 10 minutes after each 10
minutes of continuous operation.
5. Turn the compressor OFF before removing nozzle adaptor
from valve stem.
6. Remove nozzle adaptor from valve connector and store
in storage compartment.
Note: Leave the thumb latch in the open position for storing to
relieve pressure on the internal mechanism.
Using the Radio: XPower Powerpack 400R
For information about operating the radio, see page 2–5.
975-0162-01-01
3-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Power Draw
The AM/FM radio on the back panel is powered by the
internal battery in the XPower Powerpack 400R.
When turned on, the radio draws 30 mA, allowing you to use
the radio for more than one month when the XPower
Powerpack 400R is fully charged.
Listening to the AM Band
Due to signal interference, you cannot listen to the AM band
while using the XPower Powerpack 400R to operate an AC
appliance.
Connecting to an External Battery
You can extend battery operating times by connecting the
XPower Powerpack to a larger external battery.
For example, an external 60 Ah battery gives approximately
four times the operating time of the XPower Powerpack
internal 20 Ah battery.
WARNING: Fire hazard
Never allow jump-start cables’ red and black clamps to touch each
other or another common metal conductor. This could cause
damage to the unit and/or create a sparking/explosion hazard.
Always disconnect the jump-start cables from the unit after use and
clip the plastic guard over the jump-start cable port.
WARNING: Fire hazard
Jump-start cable clamps must be connected positive to positive (red
clamp to battery “+”) and negative to negative (black clamp to
battery “–”). A reverse polarity connection (positive to negative)
may cause damage to the unit and/or create a sparking/explosion
hazard.
3-16
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to an External Battery
WARNING: Acid spills
Use a sealed, non-spillable battery for indoor use. Common auto
and marine batteries are not suitable for indoor use unless their
fumes are vented outdoors. Common auto and marine batteries
contain acid, which is hazardous if spilled. Wear eye protection
and protective clothing when connecting the XPower Powerpack to
an external battery.
To connect the XPower Powerpack to an external battery
using the jump-start cables:
1. Connect the cables to the Jump-Start Cable Port on the
left side of the XPower Powerpack.
2. Connect the red positive (+) clip of the cables to the red
positive (+) terminal of the external battery.
3. Connect the black negative (–) clip of the cables to the
black negative (–) terminal of the external battery.
WARNING: Sparking and explosion
Do not remove the cables from the Jump-Start Cable Port when the
positive and negative clamps are connected to the terminals of the
external battery.
To disconnect the cables from an external battery and
from the XPower Powerpack:
1. To disconnect the XPower Powerpack from the external
battery when the external battery is discharged or no
longer needed, remove the red positive (+) clip, and then
remove the black negative (–) clip.
2. Remove the cables from the Jump-Start Cable Port.
3. Recharge the XPower Powerpack as soon as possible
after use.
CAUTION
Do not recharge the XPower Powerpack when an external battery
is connected. The AC charger may be damaged.
975-0162-01-01
3-17
Download from Www.Somanuals.com. All Manuals Search And Download.
3-18
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Maintenance
Chapter 4 provides information on maintaining your internal
battery, recharging options for the internal battery, and
replacing user-replaceable parts.
Routine maintenance is required to keep your XPower
Powerpack operating properly. Occasionally clean the
exterior of the unit with a damp cloth to remove the
accumulated dust and dirt.
WARNING: Shock hazard
Disconnect all sources of AC power and DC power before
performing any type of maintenance.
Battery Maintenance
All rechargeable batteries gradually discharge when left
standing, and you need to recharge them periodically to
maintain maximum battery capacity. The AC Charger
supplied with the XPower Powerpack is designed to regulate
the charging process, ensuring that the battery is always fully
charged but never overcharged. To ensure safe recharging
and maximum battery life, recharge the XPower Powerpack
only with the supplied charger or approved battery chargers.
s.
CAUTION
Due to inherent self-discharge, lead acid batteries must be charged
at least every 3 months, especially in a warm environment. Leaving
a battery in a discharged state, or not recharging every 3 months,
may result in permanent battery damage and poor jump-start
performance.
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
CAUTION
Do not attempt to recharge the XPower Powerpack battery if it is
frozen. Gradually warm the frozen battery to 32 °F (0 °C) before
recharging.
Recharging the XPower Powerpack Battery
To check the battery’s charge level, press the Display
Function button.
Note: Battery Charge (%) status is only accurate when the
XPower Powerpack has been disconnected from all appliances
and all charging sources for fifteen minutes.
You can recharge the battery using:
•
•
the fully automatic “plug-in-and-forget” AC Charger.
the DC Charging Cable to recharge from your vehicle as
you drive.
•
•
a generator equipped with a regulated 12 V battery
charging outlet.
a solar panel.
Recharging with the AC Charger
Recharging with the AC Charger is a true “plug-in-and-
forget” charging method.
CAUTION
Do not operate AC or DC appliances while the XPower Powerpack
is being recharged with the AC Charger.
The AC Charger may be permanently damaged if AC appliances or
12 V DC appliances are operated while the AC Charger is
connected.
4-2
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Recharging the XPower Powerpack Battery
To recharge with the AC Charger:
1. Disconnect any 12 V DC appliance and turn the light
switch to OFF.
2. Turn the AC Outlet ON/OFF switch to OFF.
3. Plug the AC Charger into a standard AC wall outlet.
4. Insert the AC Charger cable end into the Charger Input
Socket located in the charger storage compartment.
5. While the XPower Powerpack is recharging, the green
Charging Status light is flashing. If the battery is
completely discharged, a typical recharge may take up to
35 hours. When fully charged, the green Charging
Status light changes to steady and the XPower
Powerpack is ready to use.
Important: The 35-hour charging time for the XPower
Powerpack assumes that there is 120 V at the AC wall outlet. If
the voltage is less than 120 V AC, it may take more than 35 hours
to fully recharge the XPower Powerpack. If, after 35 hours of
charging, the green Charging Status light is still flashing and not
steady, continue to charge the unit for another 15 hours.
Once the battery is fully charged, the charging voltage
and current automatically reduces to a maintenance level
and the XPower Powerpack may be left permanently
connected to the AC Charger. If your utility power is
interrupted, the charging process automatically restarts
when power returns.
Recharging with the DC Charging Cable
Using the DC Charging Cable, the XPower Powerpack can
be recharged while you drive your vehicle.
Important: Although the charge regulation circuitry in the
XPower Powerpack does not operate with this charging method,
most vehicle voltage regulators will ensure that the XPower
Powerpack is not overcharged.
975-0162-01-01
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
WARNING: Fire and explosion hazard
Do not use this recharging method if your vehicle has abnormally
high voltage electrical systems that operate above 15 V DC. This
may lead to accumulations of hydrogen, causing exposure to fire
and explosion hazard.
CAUTION
Do not operate AC or DC appliances while the XPower Powerpack
is being recharged with the DC Charging Cable from your vehicle.
To recharge the XPower Powerpack while you drive using
the DC Charging Cable:
1. While the vehicle engine is running, plug one end of the
DC Charging Cable into the DC Power Socket of the
XPower Powerpack.
2. Plug the opposite end of the DC Charging Cable into the
vehicle’s lighter socket or 12 V accessory outlet.
3. Once the XPower Powerpack is fully charged or if your
vehicle’s engine is not running, disconnect the DC
Charging Cable from both sockets.
Most of the XPower Powerpack’s capacity will be restored
in four hours while the vehicle engine is running.
Note: The green Charging Status light will not illuminate when
the XPower Powerpack is recharged through the DC Charging
Cable.
Note: Battery Charge (%) indicator is only accurate when the
XPower Powerpack has been disconnected from all appliances
and all charging sources for fifteen minutes.
Important: Do not leave the XPower Powerpack permanently
connected to the vehicle’s lighter socket or 12 V accessory outlet.
4-4
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Recharging the XPower Powerpack Battery
Recharging with a Generator’s Regulated 12 V DC
Outlet
WARNING: Fire and explosion hazard
The generator output must be intended for battery charging and
have an output of 15 V or less. An unregulated output or one that
exceeds 15 V DC can damage the battery.
This may lead to accumulations of hydrogen, causing exposure to
fire and explosion hazard.
Refer to the Owner’s Guide accompanying your generator for
detailed instructions on connecting the generator to a unit like
the XPower Powerpack.
You can recharge the battery of the XPower Powerpack using
a generator in several ways:
•
Using the AC Charger to recharge the XPower
Powerpack from a generator is possible, but would
require extended generator running time.
•
Using a generator which has an auxiliary regulated 12 V
DC output designed for charging 12 V batteries. Most
generators are equipped with them. Use this power
source for faster charging.
•
Using a generator with a regulated 12 V DC lighter
socket. Follow the connection instructions in
“Recharging with the DC Charging Cable” on page 4–3.
Most of the XPower Powerpack’s battery capacity will be
recharged in a few hours.
Note: Battery Charge (%) indicator is only accurate when the
XPower Powerpack has been disconnected from all appliances
and all charging sources for fifteen minutes.
975-0162-01-01
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Recharging From a Solar Panel
Small, unregulated 12 V solar panels rated to produce a
maximum of 2.5 A (or 30 W) can be used to charge the
XPower Powerpack through the Charger Input Socket.
You will need to purchase a standard 5.5 mm OD × 2.5 mm
(0.217" × 0.10") ID DC Coaxial (barrel type) connector to
mate with the Charger Input Socket.
To recharge with a solar panel:
1. Connect the solar panel’s red positive (+) wire to the
coaxial plug’s inner contact.
2. Connect the solar panel’s black negative (–) wire to the
plug’s outer contact.
Once the connector is inserted into the Charger Input
Socket and the solar panel is placed in the sun, the
XPower Powerpack charges automatically just as with
the AC Charger. See “Recharging with the AC Charger”
on page 4–2.
It takes about ten hours in direct sunlight to recharge the
XPower Powerpack from a 2.5 A solar panel.
Replacing the Internal Battery
Battery Life
The high quality battery used in the XPower Powerpack will
serve as a reliable power source for years when properly
maintained.
To maximize battery life, it is important to recharge the
XPower Powerpack battery after each use.
Important: Recharge the XPower Powerpack fully at least
every three months if it is placed in storage or in a vehicle trunk.
Store in a location that maintains a temperature range between 32
and 86 °F (0 and 30 °C).
4-6
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Internal Battery
CAUTION
Discharging the internal battery below 10.0 V will damage the
battery and shorten its life.
Obtaining a Replacement Battery
Replacement batteries are available from stores that
specialize in and have a selection of lead acid, AGM
(Absorbed Glass Mat) batteries.
Refer to Table 4-1 for a listing of batteries approved for use
with the XPower Powerpack:
Table 4-1 Approved Replacement Batteries
Replacement Battery
Where to Buy
Panasonic
Panasonic:
#LC–X1220P
(12 V 20 Ah)
Tel: 1-800-833-9626
Digi-Key
Tel: 1-800-344-4539
EnerSys
EnerSys
#NPX–80
(12 V 20 Ah)
Tel: 1-800-962-1287 (Eastern US)
Tel: 1-800-423-4667 (Western US)
Replacing the Battery
WARNING: Shock or electrical hazard
Read this entire section before disassembling the unit.
Before attempting to replace the internal battery, make sure
you:
•
Disconnect any charging cables, 12 V DC appliances,
and AC appliances from the XPower Powerpack.
975-0162-01-01
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
•
Turn off the AC Outlet ON/OFF switch and turn off the
light switch.
•
Remove the jump-start cables.
WARNING
If you do not know how to safely remove and install batteries,
have this task performed by a qualified service technician.
WARNING: Fire hazard
When installing the replacement battery, make sure the battery
polarity is correct. Reverse polarity will damage the XPower
Powerpack and could cause serious injury.
To replace the battery:
1. Place the XPower Powerpack upright on a stable, level
surface.
2. On the XPower Powerpack, unscrew the four fasteners
on the battery cover. Place the fasteners in the cover for
safe keeping.
Fasteners
3. Disconnect the wires on the battery only.
4. After removing the old battery, position the new battery
close to the back of the XPower Powerpack.
Make sure the positive battery terminal is next to the red
positive (+) internal cable and the black negative terminal
is next to the black negative (–) internal cable.
4-8
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Incandescent Light
5. Securely fasten the bolt and washer that holds the red
positive (+) cable to the positive (+) battery terminal and
the black negative (–) cable to the negative (–) battery
terminal.
6. Do not overtighten the bolt. Consult the battery
manufacturer for torque specifications.
7. On the XPower Powerpack, replace the battery cover and
the four fasteners.
8. Dispose of the old battery in an environmentally
responsible manner.
Replacing the Incandescent Light
To replace a light bulb:
1. Turn the light switch off.
2. Unscrew the cover and lens.
3. Gently grasp the bulb and pull to remove the light
reflector assembly and the bulb.
4. While holding the light reflector assembly, gently
unscrew the black knob at the back of the assembly.
5. Remove the old bulb and insert a replacement bulb of the
same type and rating into the light reflector assembly.
6. Holding the light reflector assembly, gently screw the
black knob on to the back of the assembly.
7. Reattach the lens and cover.
975-0162-01-01
4-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Replacing the External Fuse
The replacement fuse must be rated at 250 A, 32 V DC. See
page 2–9 for a diagram. To replace the external fuse:
1. Remove the fuse cover.
2. Unscrew the two bolts on the fuse.
3. Replace the fuse. Ensure that the replacement fuse is
rated at 250 A, 32 V DC and is of the same type.
4. Tighten the fuse with the two bolts.
5. Replace the fuse cover.
4-10
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Troubleshooting
Troubleshooting will help you identify the common problems
than can occur with the XPower Powerpack.
Read this chapter before calling Customer Service.
If you cannot solve the problem with the XPower Powerpack,
record the information asked for on “Information About Your
System” on page B–8 and then call Customer Service at
1-800-394-0440.
Common Problems
Buzz in Audio Equipment
Some inexpensive stereo systems have inadequate internal
power-supply filtering and may buzz slightly when powered
by the XPower Powerpack. The best solution to eliminate the
buzzing is to use an audio system with a good quality filter.
Television Interference
The XPower Powerpack is shielded to minimize interference
with TV signals. If TV signals are weak, you may see
interference in the form of lines scrolling across the TV
screen. Try one of the following suggestions to minimize or
eliminate the interference:
•
•
•
Use an extension cord to increase the distance between
the XPower Powerpack and the TV, antenna, and cables.
Adjust the orientation of the XPower Powerpack,
television, antenna, and cables.
Maximize TV signal strength by using a better antenna.
Use a shielded antenna cable where possible.
5-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
•
Try a different TV. Different models vary considerably in
their susceptibility to interference.
Troubleshooting Reference
WARNING: Electric shock hazard
Do not remove the cover of the XPower Powerpack or
disassemble the XPower Powerpack except to replace the internal
battery or 250 A fuse. The XPower Powerpack does not contain
any internal user-serviceable parts and attempting to service the
unit yourself could result in electrical shock or burn.
Table 5-1 Troubleshooting reference
Problem
Possible Cause
Solution
AC appliance AC appliance rated
Use an AC appliance with a power
will not
operate;
more than 320 W, the rating less than 320 W.
safety overload has
audible alarm tripped.
is not
sounding.
AC appliance is rated AC appliance may exceed the
less than 320 W, high XPower Powerpack’s surge
starting surge has
tripped the safety
overload.
capability. Use an AC appliance with
a starting surge within the XPower
Powerpack surge rating.
Overload
shutdown
Appliance power
Unplug the appliance and confirm
that the appliance’s power
requirement is 320 W or less before
attempting to restart the appliance.
requirements exceed
the capability of the
XPower Powerpack.
5-2
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Reference
Table 5-1 Troubleshooting reference
Problem
Possible Cause
Solution
AC appliance Battery has discharged Turn the AC Outlet ON/OFF switch
will not
operate;
to 10.5 V.
off and recharge the XPower
Powerpack.
audible alarm
is sounding.
Inverter has
Turn the AC Outlet ON/OFF switch
overheated due to poor off and allow the XPower
ventilation or
excessively warm
environmental
conditions.
Powerpack to cool for 15 minutes or
more. Clear blocked fan opening or
remove objects covering the unit,
then restart the XPower Powerpack.
Move to a cooler environment.
Over-
Inverter has
Turn off the AC Outlet ON/OFF
temperature
shutdown
overheated due to poor switch, and let the XPower
ventilation or
excessively warm
environmental
conditions.
Powerpack cool down.
Alarm sounds Internal battery is
nearly discharged.
(11.0 V).
Turn the AC outlet ON/OFF switch
OFF and recharge the XPower
Powerpack.
If you ignore this
warning, the XPower
Powerpack
automatically switches
off when the battery
reaches 10.5 V.
Run time is
less than
Internal battery is not Recharge using the AC Charger,
fully charged.
until green Charging Status light is
expected.
steady.
AC appliance power
Check AC appliance power or
consumption is higher wattage rating (or current draw for
than expected.
12 V DC appliances) and compare
with Table 3-1 on page 3–5 and
Table 3-2 on page 3–9.
975-0162-01-01
5-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table 5-1 Troubleshooting reference
Problem
Possible Cause
Solution
Measured AC Use of an
output voltage average-reading AC
The modified sine wave (MSW)
output of the XPower Powerpack
requires a true RMS reading meter,
such as the Fluke 87 series, for
accurate measurement.
is too low.
voltmeter to read
output voltage.
Battery is almost fully Press Display Function button to
discharged.
verify battery status and recharge the
XPower Powerpack as necessary.
“Battery Charge %” reading on the
digital display is only accurate when
the XPower Powerpack has been
disconnected from all appliances and
all charging sources for fifteen
minutes.
Charging
Status light is AC wall outlet.
No AC power at the
Ensure power is available at the AC
wall outlet.
OFF when AC
Charger is
connected
AC Charger is faulty. Replace the AC Charger.
Green
Charging
Status light is display is only
flashing
(indicating
recharging)
and Battery
Charge (%)
does not turn
on.
Battery Charge (%)
reading on digital
Unplug the charging sources and any
appliances and let the XPower
Powerpack rest for 15 minutes to
obtain an accurate reading.
accurate when the
XPower Powerpack
has been disconnected
from all appliances
and all charging
sources for fifteen
minutes.
5-4
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Reference
Table 5-1 Troubleshooting reference
Problem
Possible Cause
Solution
Green
Charging
The voltage at the AC Use AC wall outlet that supplies
wall outlet is less than 120 V AC.
Status light is 120 V AC.
still flashing
and hasn’t
changed to
steady after 50
hours of
Internal battery is
permanently damaged.
Replace the battery.
charging.
The
compressor
runs but won’t placed on the valve
The valve connector
may not be securely
Check that the valve connector is
securely placed on the valve stem
before closing the thumb latch.
inflate.
stem.
The item being
inflated may have a
leak.
Check that the item being inflated
has no leaks.
Check the compressor hose for any
breaks or leaks at connections.
The
The compressor may
Turn off the compressor and let it
compressor
runs slowly.
have overheated from cool down.
excessive use.
Battery voltage is too Check the condition of the internal
low.
battery. The battery may need to be
recharged or replaced.
975-0162-01-01
5-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Table 5-1 Troubleshooting reference
Problem
Possible Cause
Solution
The engine
being jump-
XPower Powerpack
battery is not fully
Recharge the XPower Powerpack
battery.
started will not charged.
start.
The engine condition Have the engine serviced.
is poor.
External fuse (250 A) Replace 250 A, 32 V fuse with same
is blown.
type and ratings.
The engine start
capacity exceeds the
XPower Powerpack
jump-start capability.
The battery
clamps of the
jump-start
External fuse (250 A) Replace 250 A, 32 V fuse with same
is blown.
type and ratings.
cablesmeasure
zero volts.
The light does Light bulb has burnt
not turn on. out.
Remove lens cover and replace bulb
with one of the same type and rating.
The AM radio The XPower
Turn off the AC outlets.
does not work Powerpack AC outlets
or buzzes
are being used,
continuously
(XPower
causing interference.
Powerpack
400R only).
5-6
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specifications
Electrical Specifications
\
12 V DC Section
Internal battery type
sealed, AGM (Absorbed
Glass Mat) lead acid
Internal battery voltage (nominal)
Internal battery capacity (minimum)
Internal battery CCA rating
12 V DC
20 Ah
200 CCA
DC Power Socket (maximum continuous load)
Built-in incandescent light (replaceable)
Jump-start cable port
12 A with automatic reset
5 W bulb
50 A
Jump-start fuse (external—user replaceable,
replacement part # 066-0191)
250 A
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
AC Power Section
Output power
• Continuous output power
• Five minute AC output power
• AC output surge capacity
320 W
400 W
600 W
Output voltage
115 10 V AC RMS
60 Hz 4 Hz
Output frequency
Output wave form
modified sinewave
<0.20 A DC
No load current draw
Input voltage range
10.5 to 15.0 V DC
11.0 V DC
Low battery alarm
Low battery shutdown
High battery voltage shutdown
Over temperature shutdown
Overload shutdown
10.5 V DC
Yes, automatic reset
Yes, automatic reset
Yes, automatic reset
Yes, automatic reset
2 x 25 A or 1 x 50 A
AC output short circuit protection
Fuse (internal)
Operating temperature range
32 – 104 ºF
(0 – 40 ºC)
Storage temperature range
32 – 86ºF
(0 – 30 ºC)
Internal Battery Charging Controller System
AC Charger bulk charging current
750 mA
14.2 V
12.9 V
1 mA
Peak charging voltage (nominal)
Charge restart voltage (nominal)
Float charge after full charge is completed
(nominal)
AC Charger input socket maximum current
2.5 A
A-2
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
Physical Specifications
Air Compressor
250 PSI (lb./in2)
Pressure
Radio (XPower Powerpack 400R only)
AM Frequency
526–1606 KHz
87-105 MHz
FM Frequency
Accessories
Jump-start cables
(replacement part # 449-0207-01-01)
24" (0.61 m), 4 AWG wire
with black and red battery
clamps
DC charge cable
(replacement part # 449-0187-01-01)
39" (1 m) 18 AWG with male
to male lighter plugs
AC Charger input
120 10 V AC, 60 Hz
(replacement part # 074-1004)
Nozzle adaptor (for air compressor,
replacement part # 160-0015-01-01)
two nozzle adaptors
one sports needle adaptor
Physical Specifications
XPower Powerpack XPower Powerpack
Physical specifications
400 Plus
400R
Depth
Width
Height
Weight
8" (20.3 cm)
16" (40.8 cm)
9 ½" (24.1 cm)
21.8 lb. (9.9 kg)
8" (20.3 cm)
16" (40.8 cm)
9 ½" (24.1 cm)
23 lb. (10.5 kg)
Important: All specifications are subject to change without
notice.
975-0162-01-01
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Warranty and Product
Information
Appendix B contains the warranty for your XPower
Powerpack 400 Plus and XPower Powerpack 400R as well as
instructions for returning the product for servicing.
Appendix B also has a form where you can record
information, “Information About Your System” on page B–8,
in case you need to contact Customer Service.
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
What does this warranty cover? This Limited Warranty is
provided by Xantrex Technology, Inc. ("Xantrex") and covers
defects in workmanship and materials in your XPower Powerpack
400 Plus and XPower Powerpack 400R. This warranty lasts for a
Warranty Period of 6 months from the date of purchase at point of
sale to you, the original end user customer.
What will Xantrex do? Xantrex will, at its option, repair or
replace the defective product free of charge, provided that you
notify Xantrex of the product defect within the Warranty Period,
and provided that Xantrex through inspection establishes the
existence of such a defect and that it is covered by this Limited
Warranty.
Xantrex will, at its option, use new and/or reconditioned parts in
performing warranty repair and building replacement products.
Xantrex reserves the right to use parts or products of original or
improved design in the repair or replacement. If Xantrex repairs or
replaces a product, its warranty continues for the remaining portion
of the original Warranty Period or 90 days from the date of the
return shipment to the customer, whichever is greater. All replaced
products and all parts removed from repaired products become the
property of Xantrex.
Xantrex covers both parts and labor necessary to repair the product,
and return shipment to the customer via a Xantrex-selected non-
expedited surface freight within the contiguous United States and
Canada. Alaska and Hawaii are excluded. Contact Xantrex
Customer Service for details on freight policy for return shipments
outside of the contiguous United States and Canada.
How do you get service? If your product requires
troubleshooting or warranty service, contact your merchant. If you
are unable to contact your merchant, or the merchant is unable to
provide service, contact Xantrex directly at:
Phone:1-800-394-0440 (toll free)
1-360-925-5097 (direct)
Fax:1-360-925-5143 (direct)
Email:[email protected]
Direct returns may be performed according to the Xantrex Return
Material Authorization Policy described in your product manual.
For some products, Xantrex maintains a network of regional
Authorized Service Centers. Call Xantrex or check our website to
see if your product can be repaired at one of these facilities.
B-2
Download from Www.Somanuals.com. All Manuals Search And Download.
In any warranty claim, dated proof of purchase must accompany the
product and the product must not have been disassembled or
modified without prior written authorization by Xantrex.
Proof of purchase may be in any one of the following forms:
•
•
•
The dated purchase receipt from the original purchase of the
product at point of sale to the end user, or
The dated dealer invoice or purchase receipt showing original
equipment manufacturer (OEM) status, or
The dated invoice or purchase receipt showing the product
exchanged under warranty
What does this warranty not cover? This Limited Warranty
does not cover normal wear and tear of the product or costs related
to the removal, installation, or troubleshooting of the customer's
electrical systems. This warranty does not apply to and Xantrex will
not be responsible for any defect in or damage to:
a) the product if it has been misused, neglected, improperly
installed, physically damaged or altered, either internally or
externally, or damaged from improper use or use in an
unsuitable environment;
b) the product if it has been subjected to fire, water, generalized
corrosion, biological infestations, or input voltage that creates
operating conditions beyond the maximum or minimum limits
listed in the Xantrex product specifications including high
input voltage from generators and lightning strikes;
c) the product if repairs have been done to it other than by
Xantrex or its authorized service centers (hereafter "ASCs");
d) the product if it is used as a component part of a product
expressly warranted by another manufacturer;
e) the product if its original identification (trade-mark,
serial number) markings have been defaced, altered, or
removed.
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Disclaimer
Product
THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY
PROVIDED BY XANTREX IN CONNECTION WITH YOUR XANTREX
PRODUCT AND IS, WHERE PERMITTED BY LAW, IN LIEU OF ALL OTHER
WARRANTIES, CONDITIONS, GUARANTEES, REPRESENTATIONS,
OBLIGATIONS AND LIABILITIES, EXPRESS OR IMPLIED, STATUTORY OR
OTHERWISE IN CONNECTION WITH THE PRODUCT, HOWEVER ARISING
(WHETHER BY CONTRACT, TORT, NEGLIGENCE, PRINCIPLES OF
MANUFACTURER'S LIABILITY, OPERATION OF LAW, CONDUCT,
STATEMENT OR OTHERWISE), INCLUDING WITHOUT RESTRICTION ANY
IMPLIED WARRANTY OR CONDITION OF QUALITY, MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE TO
THE EXTENT REQUIRED UNDER APPLICABLE LAW TO APPLY TO THE
PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD
STIPULATED UNDER THIS LIMITED WARRANTY.
IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL, DIRECT,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSSES,
COSTS OR EXPENSES HOWEVER ARISING WHETHER IN CONTRACT OR
TORT INCLUDING WITHOUT RESTRICTION ANY ECONOMIC LOSSES OF
ANY KIND, ANY LOSS OR DAMAGE TO PROPERTY, ANY PERSONAL
INJURY, ANY DAMAGE OR INJURY ARISING FROM OR AS A RESULT OF
MISUSE OR ABUSE, OR THE INCORRECT INSTALLATION, INTEGRATION
OR OPERATION OF THE PRODUCT.
Exclusions
If this product is a consumer product, federal law does not allow an
exclusion of implied warranties. To the extent you are entitled to
implied warranties under federal law, to the extent permitted by
applicable law they are limited to the duration of this Limited
Warranty. Some states and provinces do not allow limitations or
exclusions on implied warranties or on the duration of an implied
warranty or on the limitation or exclusion of incidental or
consequential damages, so the above limitation(s) or exclusion(s)
may not apply to you. This Limited Warranty gives you specific
legal rights. You may have other rights which may vary from state
to state or province to province.
B-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning: Limitations On Use
Please refer to your product manual for limitations on uses of the
product.
SPECIFICALLY, PLEASE NOTE THAT THE XPower Powerpack
400 Plus and XPower Powerpack 400R SHOULD NOT BE USED
IN CONNECTION WITH LIFE SUPPORT SYSTEMS OR
OTHER MEDICAL EQUIPMENT OR DEVICES. WITHOUT
LIMITING THE GENERALITY OF THE FOREGOING,
XANTREX MAKES NO REPRESENTATIONS OR
WARRANTIES REGARDING THE USE OF THE XANTREX
XPower Powerpack 400 Plus and XPower Powerpack 400R IN
CONNECTION WITH LIFE SUPPORT SYSTEMS OR OTHER
MEDICAL EQUIPMENT OR DEVICES.
Please note that the XPower Powerpack 400 Plus and XPower
Powerpack 400R are not intended for use as an uninterruptible
power supply and Xantrex makes no warranty or representation in
connection with any use of the product for such purposes.
Return Material Authorization Policy
Before returning a product directly to Xantrex you must obtain a
Return Material Authorization (RMA) number and the correct
factory "Ship To" address. Products must also be shipped prepaid.
Product shipments will be refused and returned at your expense if
they are unauthorized, returned without an RMA number clearly
marked on the outside of the shipping box, if they are shipped
collect, or if they are shipped to the wrong location.
When you contact Xantrex to obtain service, please have your
instruction manual ready for reference and be prepared to supply:
•
•
•
•
The serial number of your product
Information about the installation and use of the unit
Information about the failure and/or reason for the return
A copy of your dated proof of purchase
Record these details in “Information About Your System” on
page B–8.
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Return Procedure
1. Package the unit safely, preferably using the original box and
packing materials. Please ensure that your product is shipped
fully insured in the original packaging or equivalent. This
warranty will not apply where the product is damaged due to
improper packaging.
2. Include the following:
•
•
•
•
The RMA number supplied by Xantrex Technology, Inc.
clearly marked on the outside of the box.
A return address where the unit can be shipped. Post office
boxes are not acceptable.
A contact telephone number where you can be reached
during work hours.
A brief description of the problem.
3. Ship the unit prepaid to the address provided by your Xantrex
customer service representative.
If you are returning a product from outside of the USA or
Canada In addition to the above, you MUST include return
freight funds and are fully responsible for all documents, duties,
tariffs, and deposits.
If you are returning a product to a Xantrex Authorized
Service Center (ASC) A Xantrex return material authorization
(RMA) number is not required. However, you must contact the
ASC prior to returning the product or presenting the unit to verify
any return procedures that may apply to that particular facility.
B-6
Download from Www.Somanuals.com. All Manuals Search And Download.
Out of Warranty Service
If the warranty period for your XPower Powerpack 400 Plus and
XPower Powerpack 400R has expired, if the unit was damaged by
misuse or incorrect installation, if other conditions of the warranty
have not been met, or if no dated proof of purchase is available,
your inverter may be serviced or replaced for a flat fee.
To return your XPower Powerpack 400 Plus and XPower
Powerpack 400R for out of warranty service, contact Xantrex
Customer Service for a Return Material Authorization (RMA)
number and follow the other steps outlined in “Return Procedure”
on page B–6.
Payment options such as credit card or money order will be
explained by the Customer Service Representative. In cases where
the minimum flat fee does not apply, as with incomplete units or
units with excessive damage, an additional fee will be charged. If
applicable, you will be contacted by Customer Service once your
unit has been received.
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Product Information
Information About Your System
As soon as you open your XPower Powerpack 400 Plus and
XPower Powerpack 400R package, record the following
information and be sure to keep your proof of purchase.
_______________________________
_______________________________
_______________________________
❐ Serial Number
❐ Purchased From
❐ Purchase Date
If you need to contact Customer Service, please record the
following details before calling. This information will help our
representatives give you better service.
______________________________
______________________________
______________________________
______________________________
❐ Type of installation [e.g.
RV, truck, vehicle, home]
❐ Warning, Error or Panel
Fault Message
❐ Appliances operating when
problem occurred
❐ Description of problem
____________________________________________________________
____________________________________________________________
B-8
975-0162-01-01
Download from Www.Somanuals.com. All Manuals Search And Download.
t 1-800-394-0440 (toll free in North America)
1-360-925-5097 (direct)
f 1-800-994-7828 (toll free in North America)
1-360-925-5143 (direct)
975-0162-01-01
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|