AGS
Owner's Manual
Xantrex
Automatic Generator
Start Control System
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Thank you for purchasing a Xantrex Automatic Generator
Start Control System. Xantrex Technology Inc. takes pride in
manufacturing quality products specifically designed to meet
your needs.
Main Features
The Automatic Generator Start Control System (AGS) auto-
matically controls and monitors an auxiliary generator. It will
automatically start a generator as required to charge a
battery bank or as heating or cooling systems require. You
can also set allowable generator run times, so that the
AGS does not turn on the generator at inconvenient times.
SAFETY SUMMARY
General safety information for installation and operation
is contained throughout this manual where it applies
and is not completely included in this summary.
Definitions
Warning statements identify conditions or practices which
could result in personal injury, loss of life, damage to equip-
ment or other property.
Fuse Replacement
For continued protection against the possibility of fire, replace
the fuse only with a fuse of the specified voltage, current and
type ratings.
Power Source
To avoid damage, operate the equipment only within the
specified AC (line) and DC (battery) voltages.
Servicing
There are no user serviceable parts inside. Refer all service
to qualified personnel.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
THINGS YOU SHOULD KNOW
The Automatic Generator Start Control System (AGS) has the
following features:
Starts the generator automatically in response to a low
battery. The AGS continuously monitors the house battery and
will start the generator automatically if the battery is low.
Starts the generator automatically in response to air condi-
tioning/heating requests. The AGS continually monitors the air
conditioning system and starts the generator, as required by the
air conditioning system.
Setting of QUIET TIME. QUIET TIME periods of one hour or
more can be entered to prevent automatic operation of the gen-
erator during inappropriate times.
Easy changing of time setting. A TIME ZONE indicator is pro-
vided for easy changing of local time when travelling.
Displays generator status. The Remote Panel indicates if the
generator is on (GEN ON) and if the generator has a problem
(GEN FAULT).
This system...
• allows the user to have confidence that the battery will
not be completely discharged and the DC systems will be
operational. The AGS is not dependent on shorepower and
will maintain the system even if small appliances and gen-
eral lighting are on.
• provides generator power to operate the heating or
cooling systems. This will allow you (and your pets) to be
comfortable.
The system is not intended...
• to be left unattended.
• to keep batteries fully charged. The charge period is
normally two to four hours.
• to maintain area temperature at a specific temperature.
• for use with all air conditioners, heaters, heat pumps and
generators.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
THEORY OF OPERATION
System
The AGS system, when in AUTO or AUTO QUIET TIME
mode, continuously monitors the house battery and two air
conditioning/heater thermostats.
If the LOCAL TIME of day is not within the AUTO QUIET
TIME window, it will start the generator to charge the battery
or to cool or heat as required.
The AGS system is invisible to the normal operation of the
auxiliary generator manual start and stop controls with the
following exceptions:
1. If the generator is started by the AGS, which is in
AUTO or AUTO QUIET TIME mode, the selection of OFF at
the AGS Remote Panel will stop the auxiliary generator.
2. If the AGS system commands the generator to start
and it does, the AGS system will stop the generator at the
appropriate time. If the generator stops for some other
reason, even if it is turned Off by a manual switch other than
the AGS, the AGS system will assume that there is a FAULT.
It will turn itself OFF and turn on the GEN FAULT light. At
this point, the AGS system must be turned on to the AUTO
mode or AUTO QUIET TIME mode for it to resume control of
the generator.
Once started by the AGS system, the generator will run for a
minimum of two hours. This will ensure that there is a good
charge in the battery, although it may not be fully charged at
the end of the cycle. If the battery voltage does not reach
13.5 volts during the two-hour period, the generator will
continue to run for an additional two hours. If at the end of
the second two-hour period the battery voltage is still not up
to 13.5 volts, then the AGS systems assumes that there is a
problem and turns the generator OFF. It must be restarted
manually.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
GEN ON Light
The GEN ON light is on whenever the generator is running. This
includes when the auxiliary generator is run manually.
DEFAULT: Light OFF
GEN FAULT Light
The generator has failed to start or has stopped during AGS
control. This will happen if the generator is manually stopped by a
generator start/stop switch that is independent of the AGS. Cy-
cling the ON/OFF switch will clear the fault. Check generator for
normal operation.
DEFAULT: OFF
ON/OFF MODE Switch
Pressing the ON/OFF switch changes the status of
On/Off
the AGS from OFF to AUTO to AUTO QUIET mode.
When it is off, the OFF light is illuminated.
DEFAULT: OFF mode.
AUTO Mode
In AUTO mode, the Control Module will respond to requests for
generator start from a low battery condition or from an air condi-
tioning demand.
AUTO QUIET Mode
In AUTO QUIET mode (both lights on at the same time) the Control
Module will respond to requests from low battery or air condition-
ing because the time is outside of the user-set Quiet Time. In
AUTO QUIET mode (AUTO light on and QUIET light blinking) the
AGS will not respond to requests for low battery or thermostats
starting because the Local Time is within the Quiet Time window.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PM
Set Time
Sets the LOCAL TIME, QUIET TIME “BEGIN” or QUIET TIME
“END” according to the selection made by the SELECT switch. To
set a time parameter, select the hour by repeatedly pressing the
SET TIME button until the correct hour light is on.
DEFAULT: LOCAL TIME
Time
Zone
Pressing the TIME ZONE button changes the LOCAL TIME by
cycling through the available time zones. EST (Eastern Standard
Time), CST (Central Standard Time), MST (Mountain Standard
Time), or PST (Pacific Standard Time) are possible. Only one can
be on at a time. Light is on.
DEFAULT: PST
SELECT changes the time displayed by the
Local
Time
Begin
End
AGS Remote and is used to set the TIME/
HOUR. In LOCAL TIME mode the user can set
the “Time/Hour” display to the local hour. (Min-
utes are preset at the factory and do not require
user adjustment).
Select
DEFAULT: LOCAL TIME
To Program Local Time (USUALLY NOT REQUIRED):
Use the SELECT switch to select LOCAL TIME. Press the TIME
ZONE switch to select the time zone. Press the SET TIME switch
to set the local time hour.
Quiet Time BEGIN (REQUIRED SETTING):
Use the SELECT switch and press it until the BEGIN light is on.
Use the SET TIME switch to select the time in hours Quiet Time is
to begin.
Quiet Time END (REQUIRED SETTING):
Use the SELECT switch and press it until the END light is on.
Use the SET TIME switch to select the time in hours Quiet Time is
to end.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
The Automatic Generator Start Control System (AGS) consists of
two modules, the Remote Panel and the Controller.
Service Precaution Labels
Install service precaution labels on or near the generator and near
the AGS Remote.
AGS Remote Panel
This AGS Remote Panel provides information and control of the
Control Module. Power for this Remote Panel comes from the
Control Module. The Remote Panel comes on automatically when
power is applied to the AGS Control Module.
The AGS Remote Panel measures 5.75'' (W) X 3.75'' (H) X 0.65''
(D). Use the supplied template to cut the proper size hole. Mount
the Remote Panel unit using the screws supplied.
Route the control cable from the AGS Remote Panel to the Con-
trol Module. Connect the control cable to the AGS Remote Panel
and Control Module using the data connectors on the supplied
cable.
Power Up Indications
When power is first applied to the AGS Remote, the AGS Remote
establishes communications with the Controller. It can take up to
four seconds to establish communications.
AGS Controller
The AGS Controller may be mounted in any convenient location.
Mount the AGS Controller using the screws supplied. The AGS
Controller may be mounted up to 250 feet from the AGS Remote.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
#18 AWG wire should be used. The in-line connector for the
Controller has the following DC connections.
NO. DESCRIPTION
1
2
3
4
5
START: Generator start signal contact.
STOP: Generator stop signal contact.
GENERATOR DC HOUR METER.
RESERVED (Future ignition lock-out).
POWER POSITIVE: Connect to house battery positive.
2-amp fuse required. See INSTALLATION NOTE page 10.
THERMOSTAT 1: Connected to positive signal from
thermostat/heating-cooling system, 12 VDC = ON.
THERMOSTAT 2: Connect to positive signal from thermo-
stat/heat-cooling system, 12 VDC = ON.
6
7
8
9
PREHEAT: Contact for generator preheat signal.
START COMMON: Generator Start signal contact. Typi-
cally connect to generator ground.
10
11
STOP COMMON: Generator Stop signal contact. Typically
connect to generator ground.
THERMOSTAT 3: Connected to positive signal from
thermostat/heating-cooling system, 12 VDC = ON. This is
only available on units over S/N 150.
12
13
14
15
16
BATT SENSE POSITIVE: Connect to house battery posi-
tive. 2-amp fuse required.
POWER/SENSE NEGATIVE: Connect directly to house
battery negative.
THERMOSTAT 1,3 COMMON: Contact for thermostat 1
and 3. Connected to ground.
THERMOSTAT 2 COMMON: Contact for thermostat 2.
Connected to ground.
PREHEAT COMMON: Contact for Preheat signal. Typically
connected to generator ground.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION DIAGRAM
INSTALLATION NOTE:
It is advised to interlock the AGS system so that the
AGS unit is turned off when the coach is in motion.
This may be done by removing power from the AGS
Controller. To accomplish this the AGS Controller
should be interlocked with the ignition switch to
control the POSITIVE POWER (#5) or with the parking
brake to disconnect POWER/SENSE NEGATIVE (#13).
DC CONNECTIONS
16 pin Connector
RESERVED(FOR IGN. LOCK-OUT)
GEN HOUR METER
STOP
POSITIVE POWER (+)
THERMOSTAT 1
THERMOSTAT 2
PREHEAT
START
8
7
6
5
4
3
2
1
9
16 15 14 13 12 11 10
PREHEAT
START COMMON
THERMOSTAT 2 COMMON
THERMOSTAT 1, 3 COMMON
NEGATIVE POWER/SENSE(-)
STOP COMMON
THERMOSTAT 3
BATT SENSE POSITIVE(+)
Connector view is looking into the AGS CONTROLLER.
All wires should be #18 AWG
MATING CONNECTORS:
Xantrex P/N 76-0090-01 (mating connector and harness) is
recommended for easy installation.
Note: Connector below matches both AMP and MOLEX
connectors, but pin numbers only match AMP connector.
AMP: 770583-1, PINS 770988-1
10
Download from Www.Somanuals.com. All Manuals Search And Download.
AGS REMOTE PANEL
AGS CONTROLLER
DATA CABLE
4 CONDUCTOR
SUPPLIED
11
Download from Www.Somanuals.com. All Manuals Search And Download.
COMMON QUESTIONS
Why is the display blank except for the mode lights?
If buttons are not pressed within five seconds, the Remote Panel
goes into a sleep mode to conserve energy.
Why is action not immediate?
The Remote Panel waits 15 seconds to determine if any more
changes are to be made. At the end of this period, the display
goes to sleep and actions previously entered take effect.
When the On/OFF is moved to OFF position, the generator
does not stop immediately.
The action from the buttons on the Remote Panel is delayed to
ensure that action is required.
How long is the delay from request for thermostat request to
generator start?
The time delay is 60 seconds.
What is the low battery set point and how long does the
battery voltage have to stay there to initiate a generator start?
The Low Battery set point is around 11.5 VDC. The battery voltage
must stay at or below 11.5 volts for approximately 15 seconds
before the AGS will start the generator.
PARAMETER VALUES
Low battery voltage set point
Run time for generator
11.5 VDC
2 hours
4 hours
3 times
Maximum generator run time
Number of generator start tries
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING GUIDE
The following is a list of troubleshooting items. Please see
page #8 for the installation diagram. A qualified service technician
should be contacted to service your system. Refer to the installation
diagram for more information.
PROBLEM
SOLUTION
No lights on the AGS
Remote are on
Check data cable connected to
AGS Remote Panel and AGS
Control Module. Check for 12 VDC
at AGS Controller (wires #5 and
#13).
Generator automatically
comes on but does not stay
on.
Verify that the Generator Hour
Meter Signal (wire #3) is connected
to the AGS Control Module.
Generator turns on when
batteries are charged and
air conditioner/heaters are
off.
Verify Battery Sense Positive (wire
#12) connection.
Generator does not
automatically turn on when
AGS control attempts to
turn on.
Check the preheat, if required
(wires #8 and #16) and start signal
connections (wires #1 and #9).
Generator does not
automatically turn OFF
after the AGS system runs
the generator for two
hours.
If the battery voltage did not rise
above 13.5 VDC, this is normal
operations. Otherwise check the
stop signal connections (wire #2
and #10).
AGS System starts
generator at too high of a
DC voltage.
Verify quality of Power/Sense
negative connection (wire #13).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
GLOSSARY
AGS (Automatic Generator Start Control System) A control system to
automatically start the auxiliary generator in response to a low battery
and/or cooling/heating demand.
AGS Controller The part of the AGS Control System that connects to the
wiring of the coach. It contains a micro-controller and a real-time clock.
AGS Remote Panel The user interface part of the Automatic Generator
Start Control System. It connects to the Control Module through the data
cable.
AUTO MODE In this mode the AGS will automatically start the generator
as required by a low battery or a requirement for heating/cooling.
AUTO QUIET MODE In this mode is the same as AUTO mode, except
the AGS will not start the generator during quiet hours.
Battery Sense This is the input to the AGS control module used to
determine if the battery is low. This battery sense voltage may or may not
be the same battery supplying the power to the AGS control module.
Data cable A six-pin telephone-style cable used to carry power and data
between the Remote and the Control Module.
Ground The reference potential of a circuit. In automotive use, the result
of attaching one battery cable to the body or frame which is used as a
path for completing a circuit in lieu of a direct wire from a component.
Negative Designating or pertaining to a lower electrical potential.
Positive Designating or pertaining to electrical potential; opposite of
negative. The positive battery terminal.
QUIET TIME The period of time that the AGS is prohibited from starting
the auxiliary generator regardless of battery condition or demands for
heating/cooling. The AGS is in this mode when the QUIET TIME light is
blinking.
Thermostat The heat/cooling thermostat.
Volt Short for voltage, the unit of measure for electric potential.
VDC Direct current voltage.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
What does this warranty cover?
This Limited Warranty is provided by Xantrex Technology, Inc. (“Xantrex”) and covers
defects in workmanship and materials in the Automatic Generator Start Control System.
This warranty lasts for a Warranty Period of 12 months from the date of purchase at point of
sale to you, the original end user customer.
This Limited Warranty is transferable to subsequent owners but only for the unexpired
portion of the Warranty Period.
What will Xantrex do?
Xantrex will, at its option, repair or replace the defective product free of charge, provided
that you notify Xantrex of the product defect within the Warranty Period, and provided that
Xantrex through inspection establishes the existence of such a defect and that it is covered by
this Limited Warranty.
Xantrex will, at its option, use new and/or reconditioned parts in performing warranty repair
and building replacement products. Xantrex reserves the right to use parts or products of
original or improved design in the repair or replacement. If Xantrex repairs or replaces a
product, its warranty continues for the remaining portion of the original Warranty Period or
90 days from the date of the return shipment to the customer, whichever is greater. All
replaced products and all parts removed from repaired products become the property of
Xantrex.
Xantrex covers both parts and labor necessary to repair the product, and return shipment
to the customer via a Xantrex-selected non-expedited surface freight within the contiguous
United States and Canada. Alaska and Hawaii are excluded. Contact Xantrex Customer
Service for details on freight policy for return shipments outside of the contiguous United
States and Canada.
How do you get service?
If your product requires troubleshooting or warranty service, contact your merchant. If you
are unable to contact your merchant, or the merchant is unable to provide service, contact
Xantrex directly at:
Phone: 1-800-670-0707 (toll free in North America), 1-604-422-2777 (direct)
Fax: 1-604-420-2145
Email: [email protected]
Direct returns may be performed according to the Xantrex Return Material Authorization
Policy described in your product manual. For some products, Xantrex maintains a network
of regional Authorized Service Centers. Call Xantrex or check our Web site to see if your
product can be repaired at one of these facilities.
In any warranty claim, dated proof of purchase must accompany the product, and the
product must not have been disassembled or modified without prior written authorization
from Xantrex.
Proof of purchase may be in any one of the following forms:
•
•
•
The dated purchase receipt from the original purchase of the product at point of sale
to the end user, or
The dated dealer invoice or purchase receipt showing original equipment
manufacturer (OEM) status, or
The dated invoice or purchase receipt showing the product exchanged under
warranty
15
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
What does this warranty not cover?
This Limited Warranty does not cover normal wear and tear of the product or costs related
to the removal, installation, or troubleshooting of the customer’s electrical systems. This
warranty does not apply to and Xantrex will not be responsible for any defect in or damage
to:
a) the product if it has been misused, neglected, improperly installed, physically
damaged or altered, either internally or externally, or damaged from improper use or
use in an unsuitable environment;
b) the product if it has been subjected to fire, water, generalized corrosion, biological
infestations, or input voltage that creates operating conditions beyond the maximum
or minimum limits listed in the Xantrex product specifications including high input
voltage from generators and lightning strikes;
c) the product if repairs have been done to it other than by Xantrex or its authorized
service centers (hereafter “ASCs”);
d) the product if it is used as a component part of a product expressly warranted by
another manufacturer;
e) the product if its original identification (trademark, serial number) markings have been
defaced, altered, or removed.
Disclaimer
Product
THIS LIMITED WARRANTY IS THE SOLE AND EXCLUSIVE WARRANTY PROVIDED
BY XANTREX IN CONNECTION WITH YOUR XANTREX PRODUCT AND IS, WHERE
PERMITTED BY LAW, IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS,
GUARANTEES, REPRESENTATIONS, OBLIGATIONS AND LIABILITIES, EXPRESS OR
IMPLIED, STATUTORY OR OTHERWISE IN CONNECTION WITH THE PRODUCT,
HOWEVER ARISING (WHETHER BY CONTRACT, TORT, NEGLIGENCE, PRINCIPLES
OF MANUFACTURER’S LIABILITY, OPERATION OF LAW, CONDUCT, STATEMENT OR
OTHERWISE), INCLUDING WITHOUT RESTRICTION ANY IMPLIED WARRANTY OR
CONDITION OF QUALITY, MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE TO THE EXTENT REQUIRED UNDER APPLICABLE LAW TO
APPLY TO THE PRODUCT SHALL BE LIMITED IN DURATION TO THE PERIOD
STIPULATED UNDER THIS LIMITED WARRANTY.
IN NO EVENT WILL XANTREX BE LIABLE FOR ANY SPECIAL, DIRECT, INDIRECT,
INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSSES, COSTS OR EXPENSES
HOWEVER ARISING WHETHER IN CONTRACT OR TORT INCLUDING WITHOUT
RESTRICTION ANY ECONOMIC LOSSES OF ANY KIND, ANY LOSS OR DAMAGE TO
PROPERTY, ANY PERSONAL INJURY, ANY DAMAGE OR INJURY ARISING FROM OR
AS A RESULT OF MISUSE OR ABUSE, OR THE INCORRECT INSTALLATION,
INTEGRATION OR OPERATION OF THE PRODUCT.
Exclusions
If this product is a consumer product, federal law does not allow an exclusion of implied
warranties. To the extent you are entitled to implied warranties under federal law, to the
extent permitted by applicable law they are limited to the duration of this Limited Warranty.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Some states and provinces do not allow limitations or exclusions on implied warranties or
on the duration of an implied warranty or on the limitation or exclusion of incidental or
consequential damages, so the above limitation(s) or exclusion(s) may not apply to you.
This Limited Warranty gives you specific legal rights. You may have other rights which
may vary from state to state or province to province.
Warning: Limitations On Use
Please refer to your product user manual for limitations on uses of the product.
Specifically, please note that the Automatic Generator Start Control System (AGS) is not
intended for use in connection with life support systems, and Xantrex makes no warranty
or representation in connection with any use of the product for such purposes.
Return Material Authorization Policy
Before returning a product directly to Xantrex you must obtain a Return Material
Authorization (RMA) number and the correct factory “Ship To” address. Products must also
be shipped prepaid. Product shipments will be refused and returned at your expense if
they are unauthorized, returned without an RMA number clearly marked on the outside of
the shipping box, if they are shipped collect, or if they are shipped to the wrong location.
When you contact Xantrex to obtain service, please have your instruction manual ready for
reference and be prepared to supply:
•
•
•
•
The serial number of your product
Information about the installation and use of the unit
Information about the failure and/or reason for the return
A copy of your dated proof of purchase
17
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Return Procedure
1. Package the unit safely, preferably using the original box and packing materials.
Please ensure that your product is shipped fully insured in the original packaging or
equivalent. This warranty will not apply where the product is damaged due to
improper packaging.
2. Include the following:
•
The RMA number supplied by Xantrex Technology Inc clearly marked on the outside
of the box.
•
A return address where the unit can be shipped. Post office boxes are not
acceptable.
•
•
A contact telephone number where you can be reached during work hours
A brief description of the problem
3. Ship the unit prepaid to the address provided by your Xantrex
customer service representative.
If you are returning a product from outside of the USA or Canada
In addition to the above, you MUST include return freight funds and are fully responsible
for all documents, duties, tariffs, and deposits.
If you are returning a product to a Xantrex Authorized Service
Center (ASC)
A Xantrex return material authorization (RMA) number is not required. However, you must
contact the ASC prior to returning the product or presenting the unit to verify any return
procedures that may apply to that particular facility.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
XANTREX PART NUMBERS
AGS System............................................................ 84-2064-00
includes Remote Panel, Controller, and 50' data cable (4/6 conduc-
tor)
INSTALLATION
Mating Connector ...................................... AMP 770583-1
Mating Pins (16) ......................................... AMP 770988-1
Crimping Tool ............................................. AMP 90759-1
The Xantrex AGS Harness (P/N 76-0090-01) includes these
three items.
MECHANICAL
Controller Size: 6.57'' (W) X 4.25'' (H) X 1.875'' (D)
Remote Panel Size: 5.75'' (W) X 3.75'' (H) X 0.93'' (D)
Remote Panel Cutout size: 4.875'' (W) X 2.875'' (H)
Weight: Controller.................................................. 1 lb. 12 oz.
Remote Panel........................................ 3 oz.
ELECTRICAL
Inputs:
Supply voltage.................................................. 9–15.5 VDC
Supply current .................................................. 125 mA DC
2 Thermostats DC
Battery sense.................................................... 9–15.5 VDC
Control Module Outputs:
2 wire Preheat/ Start/ Stop Lines
Remote Port Data cable (proprietary data)
ENVIRONMENTAL
Operating temperature range ................... 0–70 °C
AGS Remote ............................................... Splash proof
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Xantrex Technology Inc.
Toll free 1 800 670 0707
Direct 1 604 422 2777
Fax 1 604 420 2145
www.xantrex.com
445-0190-01-01 Rev. 1
Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|