MODEL M1102/M1103
16-SPEED DRILL PRESS
OWNER'S MANUAL
Phone: (360) 734-3482 • On-Line Technical Support: tech-support@shopfox.biz
COPYRIGHT © FEBRUARY, 2006 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in China
#7958CR
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
INTRODUCTION..................................................................................................3
Woodstock Technical Support............................................................................ 3
About Your New 16-Speed Drill Press................................................................... 3
Specifications............................................................................................... 4
Identification ............................................................................................... 5
SAFETY............................................................................................................6
Safety Instructions for Machinery ....................................................................... 6
Safety for Drill Presses.................................................................................... 8
ELECTRICAL......................................................................................................9
110V Operation............................................................................................. 9
Extension Cords ............................................................................................ 9
Grounding ................................................................................................... 9
SET UP .......................................................................................................... 10
Unpacking ..................................................................................................10
Inventory ...................................................................................................10
Machine Placement .......................................................................................11
Cleaning Machine .........................................................................................11
Column and Base..........................................................................................12
Table Support..............................................................................................12
Headstock ..................................................................................................14
Chuck Guard ...............................................................................................15
Drill Chuck & Arbor .......................................................................................15
Downfeed Handles & Belt Cover Knob.................................................................17
Table........................................................................................................17
Work Light..................................................................................................18
Test Run ....................................................................................................18
Mounting....................................................................................................19
OPERATIONS ................................................................................................... 20
General .....................................................................................................20
Installing/Removing Drill Bits ...........................................................................20
Changing Spindle RPM ....................................................................................21
Depth Stop .................................................................................................22
Adjusting Table Tilt.......................................................................................22
Arbor Removal.............................................................................................25
MAINTENANCE ................................................................................................. 26
General .....................................................................................................26
V-Belts ......................................................................................................26
Table and Base ............................................................................................26
Lubrication .................................................................................................26
Continued on next page
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE......................................................................................................... 27
Troubleshooting ...........................................................................................27
Feed Shaft Spring Tension...............................................................................30
Electrical Components ...................................................................................31
110V Wiring Diagram M1102/M1103....................................................................32
PARTS ........................................................................................................... 32
M1102/M1103 Parts Diagram ............................................................................33
M1102/M1103 Parts List..................................................................................34
Label Placement and Parts..............................................................................36
Warranty....................................................................................................37
Warranty Registration....................................................................................38
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
INTRODUCTION
Woodstock Technical Support
We stand behind our machines! In the event that questions arise about your machine, parts are miss-
ing, or a defect is found, please contact Woodstock International Technical Support at (360) 734-3482 or
lems and send out parts for warranty claims.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
About Your New 16-Speed Drill Press
Your new SHOP FOX® 16-Speed Drill Press has been specially designed to provide many years of
trouble-free service. Close attention to detail, ruggedly built parts and a rigid quality control program
assure safe and reliable operation.
The Model M1102 drill press is a 16-speed bench top model heavy duty drill press. It has a 1/2 HP
motor, a maximum work table movement of 161/4", and a spindle-to-base distance of 241/4". The Model
M1103 drill press is a 16-speed floor model heavy duty drill press with a 1/2 HP motor, a maximum
work table movement of 251/2", and a spindle-to-base distance of 48". Refer to the Specifications on
Page 3 for similarities and differences.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to include all the information necessary for safety, ease of assembly, practical use and durabil-
ity of this product.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
M1102 Specifications
Motor Type:...................................................... TEFC Capacitor Start Induction
1
Motor:........................................... /2 HP, 110V, 8.5 Amp., Single-Phase ⁄ 60 Hz
RPM: .............................................................................................. 1725
Power Transfer:........................................................................ V-Belt Drive
Bearings: ................................................... Shielded & Lubricated Ball Bearings
Power Switch: ....................................Toggle ON/OFF Switch, w/ Safety Lock Key
Lamp Switch:....................................................... Rocker Type ON/OFF Switch
Spindle Travel: ..................................................................................33/16''
Maximum Distance, Spindle to Base:....................................................... 241/4''
Maximum Distance, Spindle to Table:......................................................... 17''
Floor to Table Top Height:..........................................................87/8'' to 251/4
"
Overall Height:.................................................................................... 39''
Footprint: ............................................................................... 195/8'' to 12"
Table Tilt:....................................................................... 45° Left and Right
Table Rotation: ................................................................................. 360°
Spindle Taper:...................................................................................MT#2
Spindle to Column Distance:...................................................................61/2
"
Chuck Size: .............................................................5/8'' (1-16mm JT3), Keyed
Speed and Drive:...............................................................16, Belt Controlled
Speeds: 230, 332, 376, 470, 544, 569, 653, 760, 813, 840, 1458, 1610, 1716, 2196, 2375, 3270. RPM
Machine Weight: .............................................................................108 lbs.
Shipping Weight:.............................................................................117 lbs.
M1103 Specifications
Motor Type:...................................................... TEFC Capacitor Start Induction
1
Motor:........................................... /2 HP, 110V, 8.5 Amp., Single-Phase ⁄ 60 Hz
RPM: .............................................................................................. 1725
Power Transfer:........................................................................ V-Belt Drive
Bearings: ................................................... Shielded & Lubricated Ball Bearings
Power Switch: ....................................Toggle ON/OFF Switch, w/ Safety Lock Key
Lamp Switch:....................................................... Rocker Type ON/OFF Switch
Spindle Travel: ..................................................................................33/16''
Maximum Distance, Spindle to Base:.......................................................... 48''
Maximum Distance, Spindle to Table:...................................................... 303/4''
Floor to Table Top Height:........................................................ 195/8'' to 451/4
"
Overall Height:.................................................................................... 62''
Footprint: ............................................................................... 195/8'' to 12"
Table Tilt:....................................................................... 45° Left and Right
Table Rotation: ................................................................................. 360°
Spindle Taper:...................................................................................MT#2
Spindle to Column Distance:...................................................................61/2
"
Chuck Size: .............................................................5/8'' (1-16mm JT3), Keyed
Speed and Drive:...............................................................16, Belt Controlled
Speeds: 230, 332, 376, 470, 544, 569, 653, 760, 813, 840, 1458, 1610, 1716, 2196, 2375, 3270. RPM
Machine Weight: .............................................................................128 lbs.
Shipping Weight:.............................................................................132 lbs.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Identification
Refer to the list below and see Figure 1 to become
familiar with the drill press controls.
1. Light Switch: Turns light ON/OFF.
2. Power Switch: Turns motor ON/OFF.
1
2
3. Depth Stop: Limits quill travel to a pre-set drilling
12
depth.
3
4. Chuck Guard: Adjustable plastic shield covering the
chuck minimizes exposure to sharp drill bits.
11
4
5. Small Lock Lever: Locks table rotation.
6. Mounting Holes: When used correctly, allows for
maximum drill press stability.
10
7. Cast Iron Base with T-Nut Slots: Allows for maxi-
mum vertical clearance for drilling.
8. Rack: Allows for the geared housing to easily raise
and lower the work table in a controlled manner.
5
9
9. Table Tilt Scale: Displays current table-tilt angle.
10. Crank Handle: Raises/lowers table.
11. Feed Handles: Manual control of drilling depth.
8
12. Belt Tension Lock: Locks motor in place to maintain
belt tension.
Refer to the list below to become familiar with the
drill press terms and definitions.
6
Headstock: The cast iron upper portion of the drill press,
which houses the quill and work light, and supports the
motor and belt housing.
7
Drift Key: A wedge-shaped tool used to separate tapers.
T-Slot: A slot in a table or base used to trap a hex nut or
hex bolt to clamp down a workpiece or a vise.
Arbor: A tapered shaft that connects the chuck to the
spindle.
Quill: Houses the spindle and bearings.
Spindle: The hollow shaft that accepts the arbor.
Figure 1. Drill press features and controls.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
SAFETY
For Your Own Safety, Read Instruction Manual
Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents seri-
ous injury hazards to untrained users.
2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye-
glasses only have impact resistant lenses—they are NOT safety glasses.
3. ALWAYS WEAR AN NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT
PRODUCES DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory ill-
nesses.
4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause
permanent hearing damage.
5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which
may get caught in moving parts. Wear protective hair covering to contain long hair and wear
non-slip footwear.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Safety Instructions for Machinery
6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR
ALCOHOL. Be mentally alert at all times when running machinery.
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY.
Make sure operation instructions are safe and clearly understood.
8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the
work area.
9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.
10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power OFF and allow all moving parts to come
to a complete stop before leaving machine unattended.
11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or
where any flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.
13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords
overheat and lose power. Replace extension cords if they become damaged. DO NOT use exten-
sion cords for 220V machinery.
14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is
in OFF position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest perfor-
mance. Follow instructions for lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting
wrenches before turning machinery ON.
18. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment
of parts, broken parts, part mounting, loose bolts, and any other conditions that may affect
machine operation. Repair or replace damaged parts.
19. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was
designed.
20. SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured
workpiece protects your hands and frees both hands to operate the machine.
21. DO NOT OVERREACH. Keep proper footing and balance at all times.
22. MANY MACHINES WILL EJECT WORKPIECE TOWARD OPERATOR. Know and avoid conditions that
cause the workpiece to "kickback."
23. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.
24. BE AWARE THAT CERTAIN WOODS MAY CAUSE AN ALLERGIC REACTION. in people and animals,
especially when exposed to fine dust. Make sure you know what type of wood dust you will be
exposed to and always wear an approved respirator.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Safety for Drill Presses
READ and understand this
entire instruction manual
before using this machine.
Serious personal injury may
occur if safety and oper-
ational information is not
understood and followed.
DO NOT risk your safety by
not reading!
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
1. EYE/FACE/HAND PROTECTION. A face shield used with safety glasses is recommended. Always
keep hands and fingers away from the drill bit. Never hold a workpiece by hand while drilling! DO
NOT wear gloves when operating the drill.
2. GUARD. Only use this machine when the chuck guard is inplace and positioned over the chuck.
3. SECURING BIT. Properly tighten and securely lock the drill bit in the chuck.
4. CORRECT BIT. Use only round, hex, or triangular shank drill bits.
5. ADJUSTING KEYS AND WRENCHES. Remove all adjusting keys and wrenches before turning the
machine ON.
6. DRILLING SHEET METAL. Never drill sheet metal unless it is securely clamped to the table.
7. SURFACE /WORKPIECE PREPARATION. Never turn the drill press ON before clearing the table
of all objects (tools, scrap wood, etc.) DO NOT drill material that does not have a flat surface,
unless a suitable support is used.
8. DAMAGED TOOLS. Never use tools in poor condition. Dull or damaged cutting tools are hard to
control and may cause serious injury.
9. DRILL OPERATION. Never start the drill press with the drill bit pressed against the workpiece.
Feed the drill bit evenly into the workpiece. Back the bit out of deep holes to clear chips.
10. OPERATING SPEED. Always operate your drill press at speeds that are appropriate for the drill
bit size and the material that you are drilling.
11. MAINTENANCE/SPEED CHANGES. Never do maintenance or change speeds with the machine
plugged in to the power supply.
12. MOUNTING WORKPIECES. Use clamps or vises to secure workpiece before drilling. Position work
so you avoid drilling into the table.
13. TABLE LOCK. Make sure the table lock is tightened before starting the drill press.
14. EXPERIENCING DIFFICULTIES. If at any time you are experiencing difficulties performing the
intended operation, stop using the machine! Contact our Technical Support at (360) 734-3482.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
ELECTRICAL
110V Operation
The SHOP FOX® Model M1102/M1103 operates at 110
volts and draws 8.5 amps. Use a NEMA-style 5-15 plug
and receptacle (Figure 1) to connect your machine to
power.
We recommend connecting this machine to a dedicated
circuit with a verified ground, using a 15 amp circuit
breaker. Never replace a circuit breaker with one of
higher amperage without consulting a qualified electri-
cian to ensure compliance with wiring codes. Otherwise
you may overload the wire and plugs in the circuit.
If you are unsure about the wiring codes in your area
or you plan to connect your machine to a shared cir-
cuit, you may create a fire hazard—consult a qualified
electrician to reduce this risk.
Figure 1. Typical 110V 15A 3-prong plug
and outlet.
This equipment must be grounded.
Verify that any existing electrical out-
let and circuit you intend to plug into
is actually grounded. If it is not, it will
be necessary to run a separate 12 AWG
copper grounding wire from the outlet
to a known ground. Under no circum-
stances should the grounding pin be
removed from any three-pronged plug
or serious injury may occur.
Extension Cords
We do not recommend using an extension cord for equip-
ment. Instead, arrange the placement of your machinery
and installed wiring to eliminate the need for extension
cords. If you must use an extension cord, please use the
following guidelines:
•
•
•
•
•
Use cords rated for Standard Service
Never exceed a length of 50 feet
Use cords with 14 ga. wire or bigger
Ensure cord has a ground wire and pin
Do not use cords in need of repair
Grounding
This machine must be grounded! If your power supply
receptacle does not accommodate a ground pin, have the
receptacle replaced by a qualified electrician or have an
appropriate adapter installed and grounded properly. An
adapter with a grounding wire does not guarantee the
machine will be grounded. A ground source must be veri-
fied.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
SET UP
If any parts are missing, examine the pack-
aging for the missing parts. For any missing
parts, find the part number in the back
of this manual and contact Woodstock
International, Inc. at (360) 734-3482 or at
Unpacking
Get lifting assistance before
starting assembly. The Model
M1102/M1103 drill press is heavy.
DO NOT attempt to lift it without
help!
SUFFOCATION HAZARD!
Immediately discard all
plastic bags and pack-
ing materials to elimi-
nate choking/suffocation
hazards for children and
animals.
Your drill press has been carefully packaged for safe
transporting. If you notice the machine has been dam-
aged, please contact your authorized SHOP FOX® dealer
immediately.
Inventory
Note: Some parts and hardware may already be
installed on the machine. Make sure to check the
machine when you use this inventory list.
1
Inventory (Figure 2)
Qty
3
2
1. Headstock Assembly ....................................1
2. Arbor ......................................................1
3. Chuck Guard..............................................1
4. Chuck Key.................................................1
5. Drift Key ..................................................1
6. Chuck......................................................1
7. Knob .......................................................3
8. Downfeed Handles ......................................3
9. Table ......................................................1
10. Table Support Assembly................................1
11. Handle.....................................................1
12. Column Model M1102 ...................................1
13. Column Model M1103 ...................................1
14. Column Support Lock Lever............................1
15. Crank Handle.............................................1
16. Base........................................................1
17. Table Lock Lever ........................................1
18. Hardware Bag (Not Shown) ............................1
—Belt Cover Knob .......................................1
—Hex Wrench 3mm......................................1
—Hex Wrench 4mm......................................1
—Hex Bolt M8-1.25 x 25mm (Base) ...................4
—Lock Washer 8mm (Base) ............................4
4
5
6
7
8
9
12
10
11
14
17
15
13
16
Figure 2. M1102/M1103 box inventory.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Machine Placement
Cleaning Machine
•
•
Floor Load: This machine distributes a
heavy load in a small footprint. Some work
benches may require additional bracing to
support both the machine and a workpiece.
The unpainted surfaces are coated with a waxy
oil to protect them from corrosion during ship-
ment. Remove this protective coating with a
solvent cleaner or citrus-based degreaser. To
clean thoroughly, some parts may need to be
removed. For optimum performance from
your machine, make sure you clean all moving
parts or sliding contact surfaces that are coat-
ed. Avoid chlorine-based solvents, such as ace-
tone or brake parts cleaner, as they will damage
painted surfaces should they come in contact.
Always follow the manufacturer’s instructions
when using any type of cleaning product.
Working Clearances: Consider existing and
anticipated needs, size of material to be
processed through the machine, and space
for auxiliary stands, work tables or other
machinery when establishing a location for
your machine.
•
Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
NEVER use gasoline or
other petroleum-based
solvents to clean with.
Most have low flash
points, which make them
Get lifting assistance
before starting assembly.
The Model M1102/M1103
drill press is heavy. DO
NOT attempt to lift it
without help!
extremely
flammable.
A risk of explosion and
burning exists if these
products are used. Serious
personal injury may occur
if this warning is ignored!
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assem-
bling, adjusting or operat-
ing equipment.
ALWAYS work in well-
ventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Column and Base
The column must be secured on the base to properly
assemble your drill press.
To secure the column to the base, do these steps:
1. Place the column on the base and align the mounting
holes.
2. Secure the column to the base with the four lock
washers and hex bolts as shown in Figure 3.
Table Support
The table support must be installed as described to prop-
erly assemble your drill press.
Figure 3. Column secured to base.
To install the table support:
1. Check to make sure the pinion is inserted into the
table support, as shown in Figure 4, so the pinion
and gear teeth mesh together.
2. Mark the top of the rack, as shown in Figure 5, to
keep track of which end is up.
3. Remove the column ring by loosening the Phillips
head screw, and remove the rack.
Figure 4. Pinion correctly installed in
table support.
Continued on next page
Figure 5. Marking top of rack to show
which end is up.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
4. Place the rack inside of the table support assembly,
mesh it together with the pinion, and slide the table
support/rack assembly over the column, as shown in
Figure 6.
NOTICE
DO NOT overtighten the column ring lock screw
in the next step, or you will split the column ring.
Merely tighten it to a snug fit.
Figure 6. Sliding table support and rack
5. Slide the column ring over the column with the bev-
eled edge facing down (Figure 7), fit the beveled
edge of the column ring over the rack, and tighten
the column ring lock screw.
over the column.
Note: Make sure the rack is seated firmly in the
lower ring.
6. Install the crank handle over the pinion shaft, and
tighten the setscrew in the crank handle against the
flat part of the pinion shaft.
Figure 7. Correct column ring orientation.
Note: If the crank handle does not slide all the way
onto the pinion shaft, loosen the setscrew, and
gently tap the handle with a rubber hammer.
7. Thread the handle into the crank handle.
8. Thread the large lock lever into the back of the
table support assembly approximately three turns,
for now.
Note: The lock levers must be installed from the
non-threaded shaft sides on the table support
assembly to function correctly.
Figure 8. Handles and lock levers
9. Thread the small lock lever into the front part of
the table support assembly approximately three
turns, for now. The assembly should now be assem-
bled as shown in Figure 8.
installed.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Headstock
The headstock must be mounted on the column/base
assembly before the drill press can be operated. Moving
and installing the headstock is a two-person job.
The headstock is very heavy. In
the next step, you MUST have
assistance when moving, lifting or
mounting the headstock on the
column and base assembly.
To install the headstock, do these steps:
Figure 9. Aligning headstock with a
1. Loosen the two set screws on the right side of the
headstock enough so they are flush with the inside
pocket of the headstock.
typical drill press base.
NOTICE
When doing the next step, DO NOT force the head-
stock onto the column! If you do, you could damage
the headstock and the column.
2. With the help of an assistant, lift the headstock
assembly above the column, and gently slide it down
the column as far as it will go.
Note: An alternate method is to lay the headstock
on the packaging styrofoam and slide the column
into the headstock, tilt the assembly up, and posi-
tion the drill press on its base in the upright posi-
tion.
Figure 10. Securing headstock to column.
3. Place a ruler or tape measure on the base and
suspend a plum bob from the center of the
headstock spindle so it is over the tape/ruler as
shown in Figure 9.
4. Center the headstock directly over the base as
indicated by the plum bob and ruler.
5. Tighten the two headstock setscrews to the column,
as shown in Figure 10.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Chuck Guard
The chuck guard must be installed before the chuck is
attached to the spindle.
To install the chuck guard, do these steps:
1. Loosen the Phillips head screw and lock nut on the
chuck guard clamp.
2. Place the chuck guard over the spindle, and tighten
the Phillips head screw and lock nut.
Note: (Optional) To prevent the guard from slipping
off of the spindle, move the table up until it is just
below the guard as shown in Figure 11. Or have an
assistant hold the guard in place while you secure it.
Figure 11. Installing chuck guard.
Drill Chuck & Arbor
Chuck Key
Arbor
The drill chuck attaches to the spindle by means of the
arbor, shown in Figure 12. Matched tapers on the arbor
and the inside of the chuck create a semi-permanent
assembly when properly joined. When the drill press is
shipped from the factory, a plastic plug is installed in
the chuck.
To assemble the drill chuck and mount it to the
spindle, do these steps:
Drill Chuck
Drift Key
1. Use the chuck key to back the jaws out and remove
the plastic plug.
Figure 12. Chuck components.
2. Use mineral spirits to thoroughly clean the drill
chuck, arbor, and spindle sockets and dry all
surfaces before assembly. Follow all safety warnings
on the container of the mineral spirits. Failure to
clean the mating surfaces may cause the tapered
fit to loosen during operation, resulting in
separation and an unsafe condition.
3. Use the chuck key to adjust the jaws of the drill
chuck until they are inside the drill chuck body.
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
4. Place the drill chuck face down on a workbench. The
arbor has a short taper and a long taper. Place the
short taper into the socket in the back of the drill
chuck and tap it with a rubber or wooden mallet,
as shown in Figure 13. If the chuck fails to remain
secure on the arbor, repeat Steps 1 & 2.
DO NOT use a steel hammer on the
drill chuck to seat the arbor into the
spindle. You will damage the chuck
and/or spindle, which may make them
unusable or unsafe.
5. Raise the chuck guard.
6. Slide the arbor into the spindle socket while slowly
rotating the drill chuck. The socket has a rectangular
pocket where the tang (or flat portion of the arbor
shown in Figure 13) fits into.
7. Using only a rubber or wooden mallet, tap the chuck
and arbor assembly into the quill as shown in Figure
14. DO NOT use a steel hammer.
Figure 13. Seating arbor into chuck.
Figure 14. Seating arbor and chuck into
spindle.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Downfeed Handles & Belt
Cover Knob
The downfeed handles must be installed to properly oper-
ate the drill press.
Spindle Hub
To install the downfeed handles, do these steps:
1. Thread the knobs onto the handles, then thread the
handles into the spindle hub, as shown in Figure 15,
and tighten.
Belt Cover
Knob
2. Install the belt cover knob in its place (see Figure 15
for location).
Figure 15. Downfeed handles and belt
cover knob installed.
Table
The table must be installed to properly support the
workpiece during operation.
To install the table, do these steps:
1. Insert the table shaft into the table support assem-
bly.
Figure 16. Table installed.
2. Tighten the small locking lever (Figure 16) to secure
the table in the table support assembly.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Work Light
The Model M1102/M1103 includes a 110V light socket for
an optional light bulb. When the drill press is shipped
from the factory, a dust plug is installed in the light sock-
et for protection.
Use only bulbs that are “safety coated” and shatter
resistant. The bulb will be exposed at the bottom
of the head casting which helps with illumination.
Impacts with a bulb not “safety coated” may shat-
ter, exposing the electrical filaments and creating an
electrical shock hazard.
Keep loose clothing rolled up and out
of the way of machinery and keep hair
pulled back.
To install a light bulb in the drill press, do these steps:
1. DISCONNECT THE DRILL PRESS FROM POWER!
2. Remove the dust plug from the light socket at the
underside of the headstock.
3. Install a 60W or less light bulb.
Always wear safety glasses when oper-
ating the drill press. Failure to comply
may result in serious personal injury.
Test Run
Once assembly is complete, you are ready to test run the
drill press.
To test run the drill press:
1. Plug the drill press into the power.
2. With your finger poised on the paddle switch (in
case there is a problem), flip the START button ON.
The drill press should run smoothly, with little or no
vibration or rubbing noises.
Investigate and correct for strange or unusual noises
before operating the machine further.
If you cannot easily locate the source of a potential
problem, refer to Troubleshooting on Page 27.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Mounting
The Model M1102 must be secured to a bench. The
Model M1103 base should be secured to the floor, or
bolted to a mobile base.
Bench Mounting
To mount the Model M1102 drill press to a table:
1. Clamp the base on a bench top capable of hold-
ing approximately 100 lbs. plus the weight of the
workpiece using two clamps. Make sure the surface
is flat and stable.
Mounting Holes
2. Using holes in the base as a guide (Figure 17), drill
and bolt the base to the bench top using lag bolts,
or hex bolts, flat washers, and hex nuts.
Figure 17. Using holes as a drilling guide.
Floor Mounting
Once you have confirmed that your Model M1103 is
running properly, we strongly recommend mounting it to
the floor to ensure optimum stability.
Lag shield anchors with lag bolts and anchor studs (Figure
18) are two popular methods for anchoring an object to a
concrete floor. We suggest you research the many options
and methods for mounting your machine and choose the
best that fits your specific application.
Figure 18. Typical concrete mounting
hardware.
Mobile Base Mounting
Because the Model M1103 drill press is top-heavy by
nature, we recommend mounting it to the floor, rather
than a mobile base.
Drill presses are top-heavy and must be
securely attached to a large-footprint
base plate when used with a mobile
base. Otherwise drill press tipping and
personal injury may occur.
If you must use a mobile base, ALWAYS mount your drill
press to a base plate inside of the mobile base, as shown
in Figure 19.
Bolt Drill Press
Base to Base Plate
Bolt Base
Plate to
Mobile Base
A good quality base plate increases the standard footprint
of the drill press to make it much more stable. The base
plate must be at least 1 ⁄2" thick and made of plywood
1
(do not use OSB, MDF, or particle board as this type of
board will soak up oils, breakdown, and screws or bolts
may pull through).
Figure 19. Drill press mounted on mobile
base, using a plywood base plate for
support.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
OPERATIONS
General
The Model M1102/M1103 will perform many types of
operations that are beyond the scope of this manual.
Many of these operations can be dangerous or deadly if
performed incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate this machine. If at any
time you are experiencing difficulties performing any
operation, stop using the machine!
READ and understand this entire instruc-
tion manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
If you are an inexperienced operator, we strongly rec-
ommend that you read books, trade articles, or seek
training from an experienced Drill Press Operator before
performing any unfamiliar operations. Above all, your
safety should come first!
Installing & Removing
Drill Bits
Any drill bit you install in the chuck must be tight
enough that it will not come loose during operation.
To install a drill bit, do these steps:
Always wear safety glasses when oper-
ating the Drill Press. Failure to comply
may result in serious personal injury.
1. DISCONNECT THE DRILL PRESS FROM POWER!
2. Using the chuck key, open the drill chuck wide
enough to accept the shank of the drill bit.
3. Insert the drill bit as far as possible into the chuck
WITHOUT allowing the chuck jaws to touch the
fluted portion of the bit, and hand tighten the
chuck. Note: Make sure small bits are not trapped
between the edges of two jaws; if they are, rein-
stall the drill bit or it will not be secure enough to
use for drilling.
DO NOT investigate problems or adjust
the Drill Press while it is running.
Wait until the machine is turned OFF,
unplugged and all working parts
have come to a complete stop before
proceeding!
4. Final tighten the drill bit with the chuck key.
To remove a drill bit, do these steps:
1. DISCONNECT THE DRILL PRESS FROM POWER!
2. Use the chuck key to open the drill chuck, and
catch the drill bit with a rag to protect your hands.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Changing Spindle RPM
�
�
�
�
�
�
�
�
Never operate drill press with pulley cover in the
open position. Your hand may become trapped in the
belt and serious personal injury will occur.
�
�����
�������
������
����
���
����
����
���
���
���
���
���
���
���
���
���
����
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
���
The belts in the headstock must be rearranged to
change spindle RPM. A chart under the pulley cover
shows the belt positions needed to make the drill press
run at the desired RPM. For example, the pulley ratio
shown in Figure 20 indicates belt positioning to get 569
RPM at the spindle.
����
����
����
����
����
����
To change spindle RPM, do these steps:
Figure 20. Spindle RPM chart at 60 Hz.
1. DISCONNECT THE DRILL PRESS FROM POWER!
2. Loosen the belt tension lock knob (shown in Figure
21) on the right side of the headstock, to take ten-
sion off of the V-belts and allow the motor to move
freely.
3. Locate the desired speed on the Drill, Cutter, and
Hole Saw Suggested RPM Chart starting on Page 23.
4. Move the V-belts to the desired V-grooves on the
motor, idler, and spindle pulleys.
5. Pivot the motor toward the back of the headstock and
tighten the lock knob once the desired V-belt tension
is achieved.
Figure 21. Loosening lock knob.
6. Close the cover before plugging in the machine.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Depth Stop
The Model M1102/M1103 has a depth stop that allows
you to drill repeated non-through holes to the same
depth every time.
Jam Nut
Depth
Nut
The depth stop consists of a stud attached to the quill
with two knurled nuts that can be lowered or raised on
the stud so the lower nut (depth nut) hits a stop bracket
when the drill bit is lowered. The upper nut (jam nut)
is then used to tighten against the depth nut to secure
it in place so it doesn't move with repeated operations.
Figure 22 shows the various components of the depth
stop.
Depth Stop
Stud
Stop
Bracket
Return Height Control Nut
To set the depth stop, do these steps:
Figure 22. Depth stop components.
1. Lower the drill bit to the required height.
2. Thread the depth nut down against the stop bracket.
3. Lower the jam nut against the depth nut.
4. Hold the depth nut in place and tighten the jam nut
against the depth nut.
Adjusting Table Tilt
Lock
Bolt
Along with the standard features of a table height hand
crank and a rotating table, this drill press has a 45° left/
right table tilt feature.
Locating
Pin
To tilt the table, do these steps:
Figure 23. Table adjustment controls.
1. Loosen the lock bolt.
2. Use a 3mm hex wrench to back out the locating pin
from the hole (Figure 23) just enough so it allows
the table to tilt.
3. Tilt the table to the desired angle up to 45°.
4. Tighten the lock bolt.
5. To return the table to 0°, loosen the lock bolt, align
the arrow and the 0° mark on the angle scale, tight-
en the locating pin back into the hole, and tighten
the lock bolt.
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Arbor Removal
The arbor can be removed to install another drill chuck
in the spindle. A drift key is included to help remove the
arbor from the spindle. Usually, once the chuck and arbor
have been properly mounted together, they are consid-
ered semi-permanent connections. (If you would like to
install a different chuck, we recommend getting a new
arbor for that chuck.)
Both
Slots
Aligned
To remove the drill chuck and arbor, do these steps:
1. DISCONNECT THE DRILL PRESS FROM POWER!
2. Rotate the downfeed handles until the drift-key slot
is exposed in the side of the quill. For now, keep
the downfeed handles in this position.
3. Move the table up until it is 1⁄4" below the bottom
of the chuck, and place a towel or cloth under the
chuck.
Figure 24. Inner and outer drift-key slots
aligned.
4. Rotate the spindle until the inner drift-key slot is
aligned with the outer slot, as shown in Figure 24.
You will see through the spindle when the slot is
properly aligned.
5. Insert the drift key into the drift-key slot.
6. Tap the drift key with a rubber or wooden mallet,
as shown in Figure 25, until the chuck releases and
catch the chuck with your hand.
7. Remove the drift key and carefully retract the quill
into the headstock.
Figure 25. Using drift key to remove
arbor.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
MAINTENANCE
General
Table and Base
Periodic maintenance on your Model M1102 and
M1103 Drill Press will ensure its optimum per-
formance. Make a habit of inspecting your drill
press before each use.
Tables can be kept rust-free with regular appli-
cations of oil or anti-rust products.
Lubrication
Since all bearings are shielded and permanently
lubricated, simply leave them alone until they
need to be replaced. DO NOT lubricate them.
NEVER adjust or service
the machine while it is
running. Wait until the
machine is turned off,
unplugged and all working
parts have come to a stop
before proceeding!
For other items on this machine, such as the
quill, table and column, horizontal and verti-
cal columns, an occasional application of light
machine oil is all that is necessary to maintain
smooth rust-free operation.
Before applying any lubricant, clean off the old
lubricant, and any sawdust or metal chips.
Check for the following conditions and repair
or replace when necessary.
1. Loose or missing base mounting bolts.
2. Worn switch.
DO NOT over lubricate, your goal is to achieve
adequate lubrication. Too much lubrication will
attract dirt and sawdust, and various parts of
your machine could loose freedom of move-
ment.
3. Worn or damaged cords and plugs.
4. Damaged drive belt.
5. Loose chuck or arbor.
6. Any other condition that could hamper the
safe operation of this machine.
V-Belts
Inspect regularly for tension and wear. Check
pulleys to ensure that they are properly
aligned.
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
SERVICE
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING! DO NOT make any adjustments until power is disconnected and
moving parts have come to a complete stop!
Motor & Electrical
Symptom
Possible Cause
Possible Solution
Machine does not 1.Plug or receptacle is at fault or wired incor-
1.Test power plug and receptacle for good contact
and correct wiring.
2.Replace capacitor.
start or a breaker
trips.
rectly.
2.Start capacitor is faulty.
3.Motor connection is wired incorrectly.
4.Power supply is faulty, or is switched OFF.
3.Correct motor wiring (see Page 32).
4.Make sure all hot lines and grounds are operational
and have correct voltage on all legs.
5.Install or replace safety key, or replace switch
assembly.
5.Safety switch key is at fault.
6.ON/OFF switch is faulty.
6.Replace faulty switch.
7.Cable or wiring is open or has high resistance. 7.Troubleshoot wires for internal or external breaks,
check for disconnected or corroded connections and
repair or replace wiring.
8.Motor is at fault.
Machine stalls or 1.Incorrect spindle speed for task.
8.Test, repair or replace motor.
1.Decrease spindle speed.
is underpowered.
2.Machine is undersized for the task.
2.Use smaller drill bits/cutters and reduce the feed
rate and spindle speed.
3.Bit or cutter is dull.
3.Sharpen/replace bit or cutter.
4.Make sure hot lines and grounds are operational w/
correct voltage.
5.Replace bad belts, align pulleys, and re-tension.
6.Test power plug and receptacle for good contact
and correct wiring.
4.Low power supply voltage.
5.Belt(s) is slipping.
6.Plug or receptacle is at fault.
7.Motor connection is wired incorrectly.
8.Pulley is slipping on shaft.
9.Motor bearings are at fault.
7.Correct motor wiring (see Page 32).
8.Replace loose pulley and shaft.
9.Rotate motor shaft for noisy or burnt bearings,
repair/replace as required.
10. Motor has overheated.
11. Motor is at fault.
10. Clean inside/outside of motor, let cool, and
reduce workload on machine.
11. Test, repair or replace motor.
Continued on next page
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Symptom
Possible Cause
Possible Solution
Machine has
vibration or noisy
operation.
1.Motor or component is loose.
1.Inspect, replace for stripped or damaged bolts/
nuts, and re-tighten with thread locking fluid.
2.Replace/realign belts with a new matched set, and
retension belts (refer to Page 21).
3.Replace belts.
2.Belts are slapping belt cover.
3.V-belt(s) is worn or is loose.
4.Motor fan is rubbing on fan cover.
4.Replace/repair dented fan cover, and replace loose
or damaged fan.
5.Pulley is loose.
5.Remove pulley, replace with key as required, and
re-install securely.
6.Machine is incorrectly mounted to the floor,
or the floor is uneven.
6.Make sure floor mounting hardware is tight; place
shims under machine.
7.Chuck or cutter is at fault.
7.Replace out-of-round chuck, replace or resharpen
cutter, use appropriate feed rate and cutting RPM.
8.Check bearings, replace motor or bearings as
required.
8.Motor bearings are at fault.
9.Spindle bearings at fault.
9.Replace bearing.
Continued on next page
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Drill Press Operations
Symptom
Possible Cause
Possible Solution
Drilling stops,
but the motor
still operates.
1.The belt is loose or worn.
2.The pulley for the spindle shaft or the motor
is slipping on the shaft.
1.Replace and/or adjust the belt.
2.To resecure the pulley, do these steps:
a.DISCONNECT THE DRILL PRESS FROM POWER!
b.Remove the setscrew on the slipping pulley.
c.Align the flats on the pulley shaft with the set-
screw hole.
d.Reinstall and tighten the setscrew.
3.Bit slips in chuck.
3.Tighten bit; inspect bit for burrs or other obstruc-
tions that might interfere with clamping surface.
The chuck wob-
bles or is loose
on the spindle
shaft.
1.Foreign material is stuck between the chuck-
to-spindle mating surface.
1.Remove the chuck and clean and de-burr the tapered
chuck and spindle mating surfaces, then reassem-
ble.
2.Replace.
2.Damaged chuck.
The spindle does 1.The quill shaft is gummy with sawdust and oil. 1.Clean the gummy substance with penetrating oil and
not retract com-
pletely in the
uppermost posi-
tion or it binds.
lubricate with a light coat of oil.
2.Increase the feed shaft return spring tension as
described on Page 30.
2.The feed shaft return spring is weak.
3.The quill deflection screw is binding the quill. 3.Loosen the jam nut, and slightly turn out the screw
where the quill binds. Retighten the jam nut and
recheck for binding and looseness at all spindle loca-
tions.
The quill has
excessive deflec-
tion.
1.The quill shaft is at fault.
2.The quill and/or bearings are worn.
1.Adjust the quill screw.
2.Replace the quill and/or bearings.
Holes drilled at
an angle.
1.Table is not at 90 degrees.
1.Adjust table angle (see Page 22).
Drill bit wobbles, 1.Drill bit installed incorrectly.
2.Remove drill bit and reinstall.
holes are over-
sized.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Feed Shaft Spring
Tension
The feed shaft return spring is adjusted at the factory;
however, during the life of the drill press you may want
to adjust the feed shaft return spring so the pressure suits
your operating needs.
To adjust the feed shaft spring tension, do these
steps:
Wear safety glasses when adjusting the
coil spring. Serious eye injury may occur
if this warning is ignored!
1. DISCONNECT THE DRILL PRESS FROM POWER!
2. Wipe off any oil on the spring lock cover so it does
not slip in your fingers when you hold the cover from
spinning (see Figure 26).
Locking
Lug
Spring Cover
Lock Slot
A high tension coiled spring is underneath the cover.
Put on heavy leather gloves to protect yours hands
from possible lacerations when removing the cover
in the next step.
3. While holding the spring lock cover against the side
of the headstock so the cover stays splined with the
Spring Lock
Cover
1
locking lug; loosen the cover nut approximately ⁄4
"
(see Figure 27).
Figure 26. Feed shaft return spring
4. Pull the cover outward just enough to disengage the
assembly.
spring-cover lock slot from the locking lug.
Note: It is important to keep a good grip during this
step. Letting go of the cover will cause the spring to
rapidly uncoil.
5. Rotate the cover counterclockwise to increase spring
tension, or in the clockwise direction to reduce spring
tension.
6. Engage the next available spring-cover lock slot with
the locking lug and hold the spring lock cover tightly
against the side of the headstock.
7. Snug the cover nut against the spring cover just until
the nut stops, and then back off the nut approximately
Figure 27. Loosening cover nut.
1
⁄3
turn, or just enough so there is no binding during
complete spindle travel.
8. Tighten the cover nut.
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Electrical Components
Light Switch
Light Socket
Power
Switch
Figure 28. Power and light switch assembly.
Figure 30. Light socket with dust plug
removed.
Capacitor
Figure 29. Capacitor.
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Wiring Diagram
110V Wiring Diagram M1102/M1103
���������������������
�����
�����������������
���������
���������
�����������
����
����
�����
�����������������
�������������������
������
����������������������
��������������������
���������������������
�������������
����������
������
���������������
�����������
��������������
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Service Notes
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
M1102/M1103 Parts Diagram
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
����
��
��
��
��
��
��
�
�
����
����
��
�
��
��
�
��
��
��
��
��
�
����
��
�
��
��
�
�
��
��
��
��
�
��
��
��
��
��
��
��
��
��
�����������
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
��
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
M1102/M1103 Parts List
REF PART�#
DESCRIPTION
REF PART�#
XM1102037
DESCRIPTION
1
XM1102001
HEAD�CASTING
37
37
38
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
66
67
68
69
70
RACK�(M1102)
2
3
4
5
6
7
8
9
XM1102002
XM1102003
XM1102004
XM1102005
XPSS14M
XM1102007
XM1102008
XM1102009
XPFS11M
XM1102011
XM1102012
XPS09M
XM1102014
XPLN09M
XM1102017
XM1102018
XM1102019
XPS09M
XM1102021
XM1102022
XPHTEK31M
XM1102024
XM1102025
XPR03M
SCALE�SLEEVE
PINION�SHAFT
FEED�HANDLE�M10-1.5�X�155
KNOB�M10-1.5
XM1103037
XM1102038
XM1103038
XM1102039
XM1102040
XM1102041
XM1102042
XM1102043
XPSS01M
LONG�RACK�(M1103)
BASE�FLANGE-SHORT�(M1102)
BASE�FLANGE-LONG�(M1103)
PINION�GEAR
GEAR�
TABLE�BRACKET
GEAR�SHAFT
CRANK�ARM
SET�SCREW�M6-1�X�10
HANDLE
HEX�BOLT�M8-1.25�X�25
LOCK�WASHER��8MM
BASE
SET�SCREW�M8-1.25�X�12
KNOB�BOLT�M8-1.25�X�15
BELT�TENSION�ADJ.�ROD
COMPRESSION�SPRING
FLANGE�SCREW�M6-1�X�10
KNURLED�NUT�M8-1.25
LAMP�FRAME
PHLP�HD�SCR�M5-.8�X�10
LAMP�HOLDER
LOCK�NUT�M12-1.25
TORSION�SPRING�AND�CAP
RUBBER�BUSHING
10
11
12
13
14
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
36
XM1102045
XPB07M
XPLW04M
XM1102048
XM1102049
XM1102050
XM1102051
XPB154M
XPLW10M
XM1102054
XPSS01M
XM1102056
XM1102057
XM1102058
XM1102059
XM1102060
XM1102061
XM1102062
XM1102063
XPR23M
SCALE
POINTER
TABLE�SUPPORT�ASSEMBLY
HEX�BOLT�M16-2�X�30
LOCK�WASHER�16MM
LOCK�LEVER�M10-1.5�X�25
SET�SCREW�M6-1�X�10
LOCK�LEVER�M12-1.75�X�40
KEY�16MM�JT3
CHUCK�16MM�JT3
ARBOR�MT2�X�JT3
SPINDLE�MT2
SWITCH�BOX
PHLP�HD�SCR�M5-.8�X�10
SWITCH�MOUNTING�PLATE
PLATE�GASKET
TAP�SCREW�M4�X�14
LAMP�SWITCH
POWER�SWITCH
EXT�RETAINING�RING�12MM
BALL�BEARING�6201ZZ
RUBBER�GASKET
QUILL
COLUMN�RING
PHLP�HD�SCR�M6-1�X�10
BALL�BEARING�6204ZZ
CAP�SCREW�M6-1�X�20
DEPTH�GAUGE�HOLDER
HEX�NUT�M8-1.25
XP6201
XM1102028
XM1102029
XM1102030
XPS68M
XP6204
XPSB02M
XM1102034
XPN03M
XM1102036
XM1103036
TABLE
CHUCK�GUARD�ASSEMBLY
DRIFT�KEY
INT�RETAINING�RING�40MM
BALL�BEARING�6203ZZ
DRIVER�SLEEVE
INT�RETAINING�RING�40MM
SPINDLE�PULLEY
PULLEY�NUT�1/2-20
XP6203
XM1102067
XPR23M
XM1102069
XM1102070
COLUMN�(M1102)
LONG�COLUMN�(M1103)
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
REF PART�#
DESCRIPTION
WIRING�HARNESS
FLAT�WASHER�4MM
DEPTH�STOP�ROD
KNURLED�NUT�M12-1.75
KEY�HOLDER
MIDDLE�PULLEY�FRAME
FLANGE�SCREW�M6-1�X�10
BELT�COVER�KNOB�M6-1
V-BELT�M-22�3L220
MIDDLE�PULLEY
BALL�BEARING�6202ZZ
INT�RETAINING�RING�35MM
EXT�RETAINING�RING�15MM
BALL�BEARING�6202ZZ
V-BELT�M-22�3L220
PULLEY�GUARD
REF PART�#
DESCRIPTION
SET�SCREW�M6-1�X�10
MOTOR�PULLEY
MOTOR�CORD
MOTOR��
FLANGE�SCREW�M5-.8�X�8
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
XM1102071
XPW05M
87
88
89
90
XPSS01M
XM1102088
XM1102089
XM1102090
XM1102073
XM1102074
XM1102075
XM1102076
XPFS11M
XM1102078
XPVM22
XM1102080
XP6202
XPR21M
90-1 XPFS01M
90-2 XM1102090-2
90-3 XPC150A
90-4 XPFB12M
CAPACITOR�COVER
CAPACITOR�150MFD,�250VAC
FLANGE�BOLT�M8-1.25�X�18
PHLP�HD�SCR�M5-.8�X�10
WIRE�STRAP
STRAIN�RELIEF
HEX�NUT�M8-1.25
PHLP�HD�SCR�M5-.8�X�10
PHLP�HD�SCR�M4-.7�X�16
SET�SCREW�M8-1.25�X�28
WIRING�HARNESS
91
92
93
94
95
96
97
98
XPS09M
XM1102092
XM1102093
XPN03M
XPS09M
XPS56M
XPR05M
XP6202
XPVM22
XM1102086
XPSS87M
XM1102098
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Label Placement and Parts
Safety labels warn about machine hazards and how to prevent machine damage or injury. The
owner of this machine MUST maintain the original location and readability of all labels on this
machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the
machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.
shopfoxtools.com to order new labels.
92
91
95
96
94
97
93
REF PART�#
DESCRIPTION
XLABEL01H SAFETY�GLASSES�LABEL
XLABEL03 CLOSE�COVER�LABEL
XM1102193 MACHINE�DATA�LABEL�(M1102)
XM1103193 MACHINE�DATA�LABEL�(M1103)
XM1102194 SHOP�FOX�LOGO�PLATE
XLABEL04S ELECTRICAL�LABEL
191
192
193
193
194
195
196
197
XM1102196 MOTOR�DATA�LABEL
XM1102197 BELT�SPEEDS�LABEL
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Parts Notes
-38-
Download from Www.Somanuals.com. All Manuals Search And Download.
M1102/M1103 16-Speed Drill Press
Warranty
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work-
manship and materials for a period of two years from the date of original purchase by the original
owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence
or accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair
facility designated by our Bellingham, WA office, with proof of their purchase of the product within
two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect resulted from
causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must
bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabil-
ity standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email __________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement
____ Friend
____ Website
____ Local Store
____ Other:
_____ Mail Order Catalog
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years _____ 2-8 Years ____8-20 Years
_____ 20+ Years
3. How many of your machines or tools are Shop Fox®?
_____ 0-2 _____ 3-5 ____6-9
_____ 10+
____ No
____ No
4. Do you think your machine represents a good value?
_____ Yes
5. Would you recommend Shop Fox® products to a friend? _____ Yes
6. What is your age group?
_____ 20-29
_____ 50-59
____ 30-39
____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
_____ $20,000-$29,000
_____ $50,000-$59,000
____ $30,000-$39,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
Well Traveled Living Patio Heater 01775 User Manual
Whirlpool Clothes Dryer 3RLEQ8600 User Manual
Whirlpool Range W10234647A User Manual
Whirlpool Washer Dryer Washer Dryer Pedestal User Manual
Wyse Technology Computer Drive X90 User Manual
Xantech Stereo Amplifier FOUR CHANNEL HI POWER AMPLIFIER User Manual
Xerox Copier 7328 User Manual
Yamaha Musical Instrument Amplifier JX30B User Manual
Zanussi Clothes Dryer TDS 473E User Manual
Zanussi Microwave Oven ZMB 30 CST User Manual