MODEL W1677/W1711 SERIES
LEFT-TILT TABLE SAW
W1677EXT1 Shown
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: [email protected]
COPYRIGHT © JULY, 2002 BY WOODSTOCK INTERNATIONAL, INC. REVISED MAY, 2007 (TR).
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
Printed in Taiwan
#5674TR
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
INTRODUCTION .....................................2
MAINTENANCE .................................... 38
V-Belts ............................................38
Cleaning ..........................................38
Table & Base.....................................38
Lubrication .......................................38
Woodstock Technical Support..................2
W1677 Series Specifications...................3
W1711 Series Specifications...................4
Controls and Features...........................5
SAFETY...............................................6
Standard Safety Instructions ...................6
Specific Safety Instructions for Table Saws..8
Avoiding Potential Injuries .....................9
Kickback ..........................................11
Common Terms..................................12
SERVICE ............................................ 39
General ...........................................39
Blade Tilt Stop Bolts............................39
Blade Alignment.................................40
Miter Slot Parallel to Blade....................41
Shimming Wings .................................42
Splitter Adjustment.............................43
Angle Pointer ....................................44
Miter Gauge......................................44
Replacing V-Belts................................45
Adjusting Fence .................................45
W1677 Wiring Diagram .........................46
W1711 Wiring Diagram .........................47
Troubleshooting .................................48
ELECTRICAL ....................................... 13
220V Operation..................................13
Extension Cords .................................13
Grounding ........................................13
SETUP .............................................. 14
Unpacking ........................................14
Inventory .........................................14
Shop Fox Classic Fence Inventory ...........15
Shop Fox Original Fence Inventory...........16
Machine Placement .............................17
Cleaning Machine................................17
Mobile Base ......................................18
Assembly..........................................18
Test Run ..........................................22
PARTS .............................................. 50
Table/Body Breakdown ........................50
Motor/Trunnion Breakdown ...................52
Guard/Miter Gauge Breakdown...............54
Warranty........................................... 56
OPERATIONS ...................................... 23
General ...........................................23
Blade Height .....................................23
Feed Rate ........................................23
Blade Selection..................................24
Changing Blades .................................25
Through vs. Non-Through Cuts................26
Rip Cuts...........................................27
Blade Tilt/Bevel Cuts...........................27
Cross Cuts ........................................28
Miter Cuts ........................................28
Dado Cuts.........................................29
Rabbet Cuts ......................................31
Resawing..........................................33
Aftermarket Safety Accessories...............36
Shop-Made Safety Accessories ................37
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
INTRODUCTION
Woodstock Technical Support
Your new SHOP FOX® machine has been specially designed to provide many years of trouble-free ser-
vice. Close attention to detail, ruggedly built parts and a rigid quality control program assure safe and
reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
W1677 Series Specifications
Model Number
W1677
W1677EXT1
W1677EXT2
Motor
Voltage
Phase
Amps
3 HP
220V
3 HP
220V
3 HP
220V
Single-Phase
18
Single-Phase
18
Single-Phase
18
Speed
3450 RPM
3450 RPM
3450 RPM
Table Size (full assembly)
Table Height
401⁄8" x 27"
34"
841⁄8" x 27"
34"
841⁄8" x 27"
34"
Overall Machine Size
Footprint Size
56"L x 34"W
201⁄2"L x 201⁄2"W
410 lbs.
84"L x 34"W
201⁄2"L x 201⁄2"W
500 lbs.
84"L x 34"W
201⁄2"L x 201⁄2"W
500 lbs.
Weight
Fence
Shop Fox Classic
No
Shop Fox Classic
Yes
Shop Fox Original
Yes
Long Rails & Extension Table
Maximum Rip Right of Blade
Maximum Rip Left of Blade
Maximum Depth of Cut at 90°
Maximum Depth of Cut at 45°
26"
8"
52"
8"
49"
8"
3"
3"
3"
21⁄8
"
21⁄8
"
21⁄8
"
Maximum Blade Diameter
Arbor Size
10"
10"
10"
5
5
5
⁄8"
⁄8"
⁄8"
Arbor Speed
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
Rim Speed
Blade Tilt (Left)
Maximum Dado Width
3
3
3
Miter Slot Size
⁄
4"W x 3⁄8"H
4"
⁄
4"W x 3⁄8"H
4"
⁄
4"W x 3⁄8"H
4"
Dust Port Size
Country of Origin
Assembly Time (approx.)
Warranty
Taiwan
Taiwan
Taiwan
60 Minutes
2 Year
90 Minutes
2 Year
90 Minutes
2 Year
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
W1711 Series Specifications
Model Number
W1711
W1711EXT
W1711EXT1
W1711EXT2
Motor
Voltage
Phase
Amps
5 HP
220V
5 HP
220V
5 HP
220V
5 HP
220V
Single-Phase
25
Single-Phase
25
Single-Phase
25
Single-Phase
25
Speed
3450 RPM
3450 RPM
3450 RPM
3450 RPM
Table Size (full assembly)
Table Height
401⁄8" x 27"
841⁄8" x 27"
841⁄8" x 27"
34"
841⁄8" x 27"
34"
34"
56"L x 34"W
201⁄2"L x 201⁄2"W
410 lbs.
34"
84"L x 34"W
201⁄2"L x 201⁄2"W
500 lbs.
Overall Machine Size
Footprint Size
84"L x 34"W
201⁄2"L x 201⁄2"W
500 lbs.
84"L x 34"W
201⁄2"L x 201⁄2"W
500 lbs.
Weight
Fence
Shop Fox Classic
No
Shop Fox Classic
Yes
Shop Fox Classic
Yes
Shop Fox Original
Yes
Long Rails & Extension Table
Included Mobile Base
Included Steelex Blade
No
No
Yes
Yes
No
No
Yes
Yes
Maximum Rip Right of Blade
Maximum Rip Left of Blade
Maximum Depth of Cut at 90°
Maximum Depth of Cut at 45°
26"
8"
52"
8"
52"
8"
49"
8"
3"
3"
3"
3"
21⁄8
"
21⁄8
"
21⁄8
"
21⁄8
"
Maximum Blade Diameter
Arbor Size
10"
10"
10"
10"
5
5
5
5
⁄8"
⁄8"
⁄8"
⁄8"
Arbor Speed
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
4200 RPM
11,000 FPM
0° – 45°
13⁄16"
Rim Speed
Blade Tilt (Left)
Maximum Dado Width
3
3
3
3
Miter Slot Size
⁄
4"W x 3⁄8"H
4"
⁄
4"W x 3⁄8"H
4"
⁄
4"W x 3⁄8"H
4"
⁄
4"W x 3⁄8"H
4"
Dust Port Size
Country of Origin
Assembly Time (approx.)
Warranty
Taiwan
Taiwan
Taiwan
Taiwan
60 Minutes
2 Year
90 Minutes
2 Year
90 Minutes
2 Year
90 Minutes
2 Year
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Controls and Features
Take time to aquaint yourself with the controls
of your new table saw. They will be mentioned
frequently throughout the instructions in this
manual, and the better you know your machine,
the better you can make it perform. Figures 1
and 2 point out the key controls and their loca-
tions.
For complete details regarding the controls of
the Shop Fox Classic fence, refer to the manual
included with the fence.
Locking
Lever
Hairline
Indicator
For complete details regarding the extension
tables, refer to the manual included with those
tables.
Scale
Figure 1. Fence controls.
Blade Guard/Splitter
Miter Gauge
Fence
ON/OFF
Switch
Blade Tilt Wheel
Lock Knobs
Blade Height Wheel
Figure 2. Machine controls.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
SAFETY
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury.
This symbol is used to alert the user to useful information about proper
operation of the equipment, and/or a situation that may cause damage
to the machinery.
NOTICE
Standard Safety Instructions
1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious
injury hazards to untrained users.
2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye-
glasses only have impact resistant lenses—they are NOT safety glasses.
3. ALWAYS WEAR AN NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES
DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.
4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause
permanent hearing damage.
5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may
get caught in moving parts. Wear protective hair covering to contain long hair and wear non-slip
footwear.
6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
Be mentally alert at all times when running machinery.
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make
sure operation instructions are safe and clearly understood.
8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work
area.
9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power off and allow all moving parts to come to
a complete stop before leaving machine unattended.
11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or
where any flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.
13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over-
heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords
for 220V machinery.
14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is
in OFF position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting
wrenches before turning machinery ON.
18. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of
parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine
operation. Repair or replace damaged parts.
19. USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories.
The use of improper accessories may cause risk of injury.
20. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.
21. SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured
workpiece protects your hands and frees both hands to operate the machine.
22. DO NOT OVERREACH. Keep proper footing and balance at all times.
23. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi-
tions that cause the workpiece to "kickback."
24. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.
25. BE AWARE THAT CERTAIN DUST MAY BE HAZARDOUS to the respiratory systems of people and
animals, especially fine dust. Make sure you know the hazards associated with the type of dust you
will be exposed to and always wear a respirator approved for that type of dust.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Specific Safety Instructions for Table Saws
READ and understand this
USE this and other machinery with caution
entire instruction manual
and respect. Always consider safety first,
before using this machine.
as it applies to your individual working
Serious personal injury
conditions. No list of safety guidelines can
may occur if safety and
be complete—every shop environment is
operational information is
different. Failure to follow guidelines could
not understood and fol-
result in serious personal injury, damage
lowed. DO NOT risk your
to equipment or poor work results.
safety by not reading!
1. Always use guard, splitter and anti-kickback pawls on all ''through-sawing'' operations. Through-
sawing operations are those when the blade cuts completely through the workpiece as in ripping or
crosscutting.
2. Always hold the work firmly against the miter gauge or the fence when cutting.
3. Always use a push-stick for ripping narrow stock.
4. Never perform any operation ''free-hand'' which means using only your hands to support or guide the
workpiece. Always use either the fence or the miter gauge to position and guide the work.
5. Never stand or have any part of your body in line with the path of the saw blade.
6. Never reach behind or over the blade with either hand for any reason.
7. Move the rip fence out of the way when crosscutting with the miter gauge.
8. Always use multiple light passes when cutting deep non-through cuts.
9. Never attempt to free a stalled saw blade without first turning the saw OFF.
10. Provide adequate support to the rear and sides of the saw table for wide or long workpieces.
11. Avoid kickbacks. A condition in which a piece of wood is thrown back towards an operator at a high
rate of speed. Usually is caused by the stock becoming trapped between the stationary face of the
rip fence and the rotating side of the saw blade. Do not operate the machine until you know what
a kickback is and how to avoid it.
12. Avoid awkward operations and hand positions where a sudden slip could cause your hand to move
into the blade.
13. Avoid cutting warped stock or stock that may contain loose knots, nails or any other defects. These
conditions may cause kickback.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Avoiding Potential Injuries
Figure 3. Unplug saw before changing blades.
Figure 5. Do not freehand cuts.
Figure 4. Never use the rip fence as a guide when
Figure 6. Do not make through cuts without the
cutting with the miter gauge.
blade guard/splitter in place.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Avoiding Potential Injuries
Figure 7. Do not make unstable cuts.
Figure 9. Use a push stick when ripping
narrow pieces.
Figure 10. Do not stand directly behind blade
Figure 8. Use featherboards when possible
when making a cut.
to protect against kickback.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Kickback
Kickback occurs when the blade launches the workpiece toward the front of the saw. This happens so
quickly the operator rarely has time to respond. He or she can be killed, severely hurt or have his/her
hand forced into the moving blade. Kickback is one of the most serious dangers that can occur with a
table saw. In order to protect yourself from kickback, it is essential to educate yourself about why and
how it happens. Below is a list of ways to protect yourself from kickback.
•
Do not stand directly behind the
•
•
Do not reach behind the blade to pull the
workpiece through the cut. In the event
of a kickback, your hand may be pulled
into the moving blade.
workpiece. Should a kickback occur, the
workpiece may be launched at a high rate of
speed in the direction from which it came.
If you are standing behind the workpiece, it
will hit you. Instead, stand off to the side in
a location where you are still able to main-
tain total control.
Use push sticks or push paddles when-
ever possible. Using one or two push sticks
when ripping can decrease operator injury
in the event of kickback. Push sticks and
push paddles create a barrier between
your hands and the workpiece.
•
•
Do not use the rip fence as a guide when
crosscutting with the miter gauge. The
workpiece may pinch the blade, causing
kickback. Use the miter gauge and the rip
fence by themselves—never together.
•
•
Be aware that small cutoff pieces are
easily kickbacked if loose near the blade.
Use a zero-clearance table insert whenever
possible.
Only use sharp, clean blades. Sharp blades
will cut the material easier, reducing the
chance that the blade will get jammed up
while cutting the workpiece. Always replace
or sharpen your dull blades. Blades covered
in resin are just as likely to cause kickback
as a dull blade.
Always use the blade guard/splitter
when making through-cuts. The blade
splitter has anti-kickback pawls that dig
into the workpiece in the event of a kick-
back. Removing the guard/splitter greatly
increases the risk of danger from kickback.
•
•
Never freehand a cut with the table saw.
The small twists or turns that are inherent
with freehand cuts will cause kickback.
•
•
Always feed material into the blade at
the proper feed rate. Feeding material
into the blade too fast may cause a kick-
back. Listen to the blade and the motor
during a cut. If either one is struggling,
decrease the feed rate.
Keep your table saw clean. Buildup of
wood chips or dust, or any other objects
that may obstruct an otherwise smooth cut,
has the potential to cause kickback.
Consider aftermarket or shop-made
accessories to increase your level of safe-
ty. Many of these items are designed to
stop the board during a kickback or reduce
the chance of kickback by stabilizing the
board during a cut.
•
Cutting warped stock or stock with loose
knots, nails, or other defects will cause
kickback.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Common Terms
In order to increase user safety awareness and understanding, we have provided a list of common terms
associated with table saws. We will refer to many of these terms throughout this manual, so the time you
spend learning these terms will result in an increased knowledge of table saw applications.
Non Through-Cut
Arbor
A cut that does not pass through the top of the
workpiece—i.e. a dado or rabbet cut. This type
of cut is more dangerous than a through cut
because it requires the operator to remove the
blade guard/splitter assembly.
The shaft underneath the table on which
the blade mounts.
Bevel
An angled cut on the edge of a board that reach-
es both faces of the board.
Examples:
Dado Cutting: Page 29
Rabbet Cutting: Page 31
Resawing: Page 33
Crosscut
To cut across the grain of a piece of stock.
Dado
Outfeed Side
A slot cut partially through the thickness of the
stock either with or against the grain.
The opposite side of the table that the workpiece
is fed into the blade. Usually supplemented with
an aftermarket or shop-made table to catch a
freshly cut workpiece.
Feed Rate
The speed at which the stock is pushed into the
moving blade.
Positive Stop
A bolt or pin that can be adjusted to stop a mov-
ing part at a predetermined location. This table
saw has positive stops for tilting the blade.
Flush
A condition when two or more surfaces are per-
fectly flat and parallel to each other, so that
their touching edges have an even surface.
Rabbet
An L-shaped cut along the edge of a workpiece.
Kerf
The width of the material that a blade removes
from the workpiece.
Rip Cut
To cut along the grain of stock (see Page 27).
Kickback
Straightedge
The event in which the stock is ejected from the
blade at a high rate of speed toward the opera-
tor. Usually caused by binding the blade or by
a blade condition that forces the momentum of
the blade to push the stock away.
An object with a perfectly straight edge that
is used to compare against another object to
determine whether it is straight.
Through-Cut
A cut that passes completely through the top
of the workpiece. The blade guard MUST be
installed for safest operation.
Examples:
Miter Cut
An angled cut across the face or end of a board.
Usually cut to match another board of a corre-
sponding angle so that each cut piece fits per-
fectly into the other, thus changing the direc-
tion of the workpiece.
Rip Cuts: Page 27
Crosscutting: Page 28
Miter Cuts: Page 28
Blade Tilt/Bevel Cuts: Page 27
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
ELECTRICAL
220V Operation
The Model W1677/W1711 is prewired for 220V operation.
Always connect this machine to a dedicated circuit with a
verified ground, using the recommended circuit size and
power connection method stated below.
Electrocution or severe shock could
occur if machine is not grounded.
Never replace a circuit breaker with one of higher amper-
age without consulting a qualified electrician to ensure
compliance with wiring codes. If you are unsure about
the wiring codes in your area or plan to connect your
machine to a shared circuit, you may create a fire haz-
ard—consult a qualified electrician to reduce this risk.
Extension Cords
Replacing an existing circuit breaker
with one rated for higher amperage
may result in a fire. Get help from an
electrician if your circuit is too small
for the machine.
We do not recommend using an extension cord with your
machine. If you have no other choice, use the following
guidelines:
•
•
•
•
Use cords rated for Standard Service
Never exceed a length of 50 feet
Ensure cord has a ground wire and pin
Do not use cords in need of repair
Grounding
L6-20 P
L6-20 R
This machine must be grounded! Verify that any exist-
ing electrical outlet and circuit you intend to plug into
is actually grounded. If it is not, it will be necessary to
run a separate copper grounding wire, of the appropri-
ate size, from the outlet to a known ground. Under no
circumstances should you connect your machine to an
ungrounded power source or electrocution or severe
shock could occur.
L6-30 P
L6-30 R
Figure 11. Plug & receptacle examples.
Model
Operating Voltage Amp Draw Min. Circuit Size Plug/Receptacle
Extension Cord
W1677 Series
W1711 Series
220V
220V
18 Amps
25 Amps
20A
30A
NEMA L6-20
NEMA L6-30
12 Gauge
8 Gauge
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
SETUP
Unpacking
Your new table saw has been carefully packaged for safe
transporting. When unpacking, remove the red shipping
braces that hold the saw to the pallet. If you notice the
machine has been damaged, please contact your autho-
rized SHOP FOX® dealer immediately.
Inventory
The following is a description of the main components
shipped in the table saw box. Lay the components out
to inventory them. Note: Some parts and hardware may
already be installed on the machine. Make sure to check
the machine when you use this inventory list.
A
Box Inventory (Figures 12 & 13)
Qty
A. Saw Base Unit..............................................1
B. Extension Wings ...........................................2
C. Cabinet Cover..............................................1
D. Lock Knob...................................................1
E. Handwheel..................................................1
F. Miter Gauge ................................................1
G. Blade Guard/Splitter......................................1
H. Dado Table Insert .........................................1
I. Standard Table Insert.....................................1
J. Dust Port....................................................1
K. Arbor Wrench ..............................................1
L. Support Shaft ..............................................1
M. Blade Guard Brackets.....................................2
N. Handwheel Handle ........................................1
O. Switch Support Bracket...................................1
Figure 12. Saw base unit.
C
B
D
E
Hardware and Tools
Qty
Flat Head Screw 5⁄16"-18 x 1" (Switch Bracket).......1
F
•
•
•
•
•
•
•
•
•
•
•
•
•
G
Flat Washer 5⁄16" (Switch Bracket)......................1
Hex Nut 5⁄16"-18 (Switch Bracket).......................1
Tap Screws 10-24 x 3⁄8" (Dust Port) ....................4
Set Screws 5⁄16"-18 x 3⁄8" (Brackets on Shaft).........2
Hex Bolt 5⁄16"-18 x 11⁄2" (Brackets on Shaft) ..........2
Flat Washers 5⁄16" (Brackets on Shaft) .................4
Lock Washers 5⁄16" (Brackets on Shaft).................2
Hex Nuts 5⁄16"-18 (Brackets on Shaft) ..................2
Hex Bolts 5⁄16"-18 x 1" (Guard/Splitter Install) .......2
Flat Washers 5⁄16" (Guard/Splitter Install).............2
Hex Wrenches 3, 4, 8mm .........................1 each
Flat Wrench ................................................1
K
M
H
J
L
I
N
O
Figure 13. Table saw loose parts.
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Shop Fox Classic Fence
Inventory
C
D
B
A
Depending on which model you purchased, your saw will
come with standard length rails or with long rails. The
Shop Fox Classic fence includes extra hardware for mount-
ing it to other brands of table saws.
The inventory list below and Figures 14 & 15 show only
the hardware needed to mount the fence to your saw. To
avoid confusion, we suggest removing any items not listed
here from your immediate work area.
E
Figure 14. Classic fence inventory for
Inventory Needed for Your Saw
Standard Rails (Figure 14):
standard rails.
Qty
A. Fence Assembly............................................1
B. Front Rail 461⁄2" ...........................................1
C. Back Rail 461⁄2" ............................................1
D. Front Rail Rectangular Tube 54" ........................1
E. Scale.........................................................1
C
A
B
Long Rails (Figure 15):
Qty
A. Front Rail Rectangular Tube 84" ........................1
B. Extension Table............................................1
C. Legs..........................................................2
D. Feet..........................................................2
E. Front Rail 72" ..............................................1
F. Back Rail 72" ...............................................1
G. Fence Assembly............................................1
H. Leg Braces ..................................................2
I. Scale.........................................................1
E
F
D
I
G
H
Figure 15. Classic fence inventory for long
rails.
Common Rail/Table Mounting Hardware:
Additional Hardware Only for Long Rail Setup:
•
•
•
•
Hex Bolts 3⁄8-16 x 1" (Rail/Table)...........4
Flat Washers 3⁄8" (Rail/Table)...............4
Hex Bolts 1⁄4-20 x 3⁄4" (Rail/Tube)..........4
Flat Washers 1⁄4" (Rail/Tube)................4
•
•
•
•
•
•
•
•
•
•
•
•
Hex Bolts 1⁄4-20 x 3⁄4" (Rail/Tube)..........3
Flat Washers 1⁄4" (Rail/Tube)................3
Hex Bolts 3⁄8"-16 x 13⁄4" (Rail/Ext Table)..8
Flat Washers 3⁄8" (Rail/Ext Table) .........16
Hex Nuts 3⁄8"-16 (Rail/Ext Table)...........8
Hex Nuts 1⁄2" (Feet Jam Nuts)...............2
Wood Screws 1⁄4" x 3⁄4" (Brace/Ext Table) 2
Fender Washers 1⁄4" (Brace/Ext Table) ....2
Hex Bolts 3⁄8"-16 x 3⁄4" (Brace/Leg) ........2
Flat Washers 3⁄8" (Brace/Leg) ...............2
Flat Washers 3⁄8" (Spacers for Brace/Leg).8
Wood Screws #8 x 3⁄4" (Leg/Ext Table) ...12
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Shop Fox Original Fence
Inventory
Depending on which model you purchased, your saw will
come with standard length rails or long rails. The Shop
Fox Original fence includes extra hardware for mounting it
to other brands of table saws.
A
B
The inventory list below and Figures 16 & 17 show only
the hardware needed to mount the fence to your saw. To
avoid confusion, we suggest removing any items not listed
here from your immediate work area. The hardware list
below is categorized by application.
C
E
F
D
Inventory Needed for Your Saw
Standard Rails (Figure 16):
Qty
A. Shop Fox Original Fence..................................1
B. Front Rail ...................................................1
C. Rear Rail ....................................................1
D. Scale.........................................................1
E. End Braces..................................................2
F. Rail End Covers ............................................4
Figure 16. Original fence inventory for
standard fence rails.
A
Long Rails (Figure 17):
Qty
B
A. Shop Fox Original Fence..................................1
B. Extension Table............................................1
C. Legs..........................................................2
D. Feet..........................................................2
E. Front Rail 72" ..............................................1
F. Back Rail 72" ...............................................1
G. Scale.........................................................1
H. End Braces..................................................2
I. Table Leg Braces ..........................................2
J. Rail End Covers ............................................4
E
C
F
D
H
I
J
G
Figure 17. Original fence inventory for
long fence rails.
Common Rail/Table Mounting Hardware:
•
•
Hex Bolts 3⁄8-16 x 1" (R Rail/Main Table)..2
Low Profile Hex Bolts 3⁄8-16 x 1"
Additional Hardware Only for Long Rails:
•
•
•
•
•
•
•
•
•
•
Hex Bolts 3⁄8"-16 x 13⁄4" (Rail/Ext Table)..8
Flat Washers 3⁄8" (Rail/Ext Table) .........16
Hex Nuts 3⁄8"-16 (Rail/Ext Table)...........8
Hex Nuts 1⁄2" (Feet Jam Nuts)...............2
Wood Screws 1⁄4" x 3⁄4" (Brace/Ext Table) 2
Fender Washers 1⁄4" (Brace/Ext Table) ....2
Hex Bolts 3⁄8"-16 x 3⁄4" (Brace/Leg) ........2
Flat Washers 3⁄8" (Brace/Leg) ...............2
Flat Washers 3⁄8" (Spacers for Brace/Leg).8
Wood Screws #8 x 3⁄4" (Leg/Ext Table) ...12
(F Rail/Main Table) ...........................2
Flat Washers 3⁄8" (Rail/Main Table) ........8
Hex Bolts 3⁄8-16 x 1" (End Braces) ..........2
Flat Washers 3⁄8" (End Braces) ..............2
Hex Nuts 3⁄8"-16 (End Braces) ...............2
Flat Hd Screw 1⁄4"-20 x 5⁄8" (End Braces)..1
Flat Washer 1⁄4" (End Braces) ...............1
Hex Nut 1⁄4"-20 (End Braces) ................1
Fence Stop......................................1
Phlp Hd Screw 10-24 x 5/8"..................1
Flat Washer #10 ...............................1
•
•
•
•
•
•
•
•
•
•
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Machine Placement
Cleaning Machine
•
•
Floor Load: This machine distributes a
heavy load in a small footprint. Some floors
may require additional bracing to support
both machine and operator.
The unpainted parts of your machine type are
coated with a shipping grease that protects
them from corrosion during shipment. This coat-
ing does its job well, but requires a little elbow
grease to remove.
Working Clearances: Consider the following
when establishing a location for your
machine:
The shipping grease can be cleaned off with a
solvent, petroleum or citrus-based degreaser.
DO NOT use chlorine-based solvents such as
brake parts cleaner or acetone—if you happen
to splash some onto a painted surface, you will
ruin the finish.
— Existing and anticipated needs
— Size of material to be processed
— Space for auxiliary stands, work tables or
other machinery
— Room to perform maintenance inside the
cabinet.
Here is one easy and popular method for clean-
ing the shipping grease: Soak the grease in
WD-40® or a similar product, wait five minutes,
scrape most of the grease off with a plastic
putty knife or other straight edge that won't
scratch the cast iron, re-soak, then wipe down
with a shop rag.
•
•
Lighting: Lighting should be bright enough
to eliminate shadow and prevent eye strain.
Electrical: Electrical circuits must be
dedicated or large enough to handle
amperage requirements. Outlets must be
located near each machine, so high-traffic
areas are clear of power cords. Follow local
electrical codes for proper installation of
new lighting, outlets, or circuits.
NEVER use gasoline or
other petroleum-based
solvents to clean with.
Most have low flash
points, which make them
extremely
flammable.
USE helpers or power
lifting equipment to lift
this machine. Otherwise,
serious personal injury
may occur.
A risk of explosion and
burning exists if these
products are used. Serious
personal injury may occur
if this warning is ignored!
MAKE your shop “child
safe.” Ensure that your
workplace is inaccessible
to youngsters by closing
and locking all entrances
when you are away. NEVER
allow untrained visitors in
your shop when assem-
bling, adjusting or operat-
ing equipment.
ALWAYS work in well-
ventilated areas far from
possible ignition sources
when using solvents to
clean machinery. Many
solvents are toxic when
inhaled or ingested. Use
care when disposing
of waste rags and
towels to be sure they
DO NOT create fire or
environmental hazards.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Mobile Base
If your model includes a mobile base kit, or you plan to
use an aftermarket mobile base kit for your saw, we rec-
ommend assembling the saw on the mobile base to avoid
heavy/awkward lifting later.
Assemble your mobile base equipment as detailed in
the instructions included with the mobile base, then put
the saw base unit on the mobile base before continuing
assembly.
Assembly
You can mount the extension wings yourself, but it is
easier with help.
Figure 18. Extension wing attached to
table.
Note: If you have a model with long rails and an exten-
sion table, leave the right wing off to make room for the
extension table.
To assemble your table saw, do these steps:
1. Using the fasteners that come pre-installed in the
table, attach the extension wings to the table, as
shown in Figure 18. Do not completely tighten the
bolts at this point.
2. Place a straightedge across the table and the exten-
sion wings, and adjust each wing until it is flush
with the table, then tighten the bolts underneath to
secure the wing in place.
Figure 19. Checking overall table flatness
with a straightedge.
3. Check the overall flatness of the table and exten-
sion wing assembly with a straightedge, as shown in
Figure 19.
Note: If an extension wing tilts up or down at the
outside edges, shim it with masking tape or shim
stock (refer to Shimming Wings on Page 42).
4. Attach the switch bracket to the backside of the
left extension wing with the 5⁄16"-18 x 1" Phillips flat
head screw, 5⁄16" flat washer, and 5⁄16" nut, as shown
in Figure 20.
Figure 20. Attaching switch to extension
wing.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
5. Mount the switch brace, as shown in Figure 21,
using the table mounting fasteners on the top end
and the switch mounting fasteners on the bottom
end.
Figure 21. Switch brace installed.
6. Install the handwheel over the threads, screw the
lock knob into the center, and attach the handle to
the handwheel, as shown in Figure 22.
Figure 22. Installing handwheel, lock knob
and handle.
7. Mount the dust port onto the cabinet stand with the
four 10-24 x 3⁄8" tap screws, as shown in Figure 23.
Figure 23. Installing dust port.
8. Remove the motor shipping brace, shown in Figure
24, then replace the fasteners that held the brace
back into the hole from which they came.
Figure 24. Motor shipping brace.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
9. Install the blade by removing the arbor nut from
the arbor and placing the blade on the arbor so the
teeth face toward the front of the saw.
10. Hold the blade on the arbor with one hand and tight-
en the arbor nut on the arbor with the other.
11. Brace the blade with a scrap piece of wood, as
shown in Figure 25, and tighten the arbor nut with
the arbor wrench. DO NOT overtighten the nut or it
will be difficult to remove when you need to change
your blades.
Figure 25. Installing blade.
12. Attach the fence as detailed in the instruction manu-
al included with the fence.
13. Screw the splitter shaft into the tilt assembly
through the back of the cabinet, as shown in Figure
26.
14. Slide the lower half of the bracket onto the split-
ter shaft and temporarily tighten the bracket to the
shaft with the two 5⁄16"-18 x 3⁄8" set screws.
15. Place the upper blade guard bracket on the lower
blade guard bracket and secure them with the two
5⁄16"-18 x 11⁄2" bolts, four 5⁄16" flat washers, two 5⁄16"
lock washers, and two 5⁄16" hex nuts, as shown in
Figure 27. Do not fully tighten the nuts yet.
Figure 26. Installing the splitter shaft.
The blade guard/splitter greatly reduces the risk of
injury when using this saw. You MUST install the blade
guard/splitter before operating the machine.
Figure 27. Blade guard bracket assembly
installed on splitter shaft.
16. Attach the blade splitter/guard assembly at the
mounting locations shown in Figure 28. Use the
two 5⁄16"-18 x 1" hex bolts and two 5⁄16" flat washers
from the inventory hardware to connect the splitter
to the shaft bracket. Leave the mounting bolts just
loose enough to slide the blade splitter on and off
during alignment.
Mounting Locations
Set Screws
Figure 28. Blade splitter/guard assembly
attached.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
17. Raise the blade up to full height, and use a straight-
edge to align the blade with the blade splitter, as
shown in Figure 29.
18. At the front mounting location on the splitter, use
the provided washers (or get thinner electrical wash-
ers) to shim between the splitter and the casting
to take up any space, and tighten all the splitter
mounting bolts.
Figure 29. Aligning splitter to blade.
19. Loosen the set screws on the lower bracket half (see
Figure 28), square the splitter to the table (Figure
30), and retighten the set screws.
Figure 30. Squaring splitter.
20. Place the table insert into the table opening, and
using a straightedge as a guide, adjust the table
insert set screws (Figure 31) until the table insert is
flush with the table top.
21. Install the cabinet cover by lining up the hinges and
tapping the hinge pins down into the hinges with a
hammer.
Note: Paint can sometimes get into the hinge pin
holes during manufacturing. If you have difficulty
installing the hinge pins, use a round file or other
similar tool to remove this paint for easier installa-
tion.
Figure 31. Adjusting table insert flush
with table top.
22. Install the fence and rails as instructed in the
owner's manual included with your fence. (Refer to
Pages 15 and 16 to clarify which fence parts are
needed for your machine.)
Note: After installing the fence, you MUST make
sure the fence is correctly adjusted parallel with
the blade before making any cuts. A fence that is
not parallel with the blade invites workpiece bind-
ing, which may lead to kickback and injury.
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Test Run
Before you test run the machine, do these steps:
1. Read all the warnings and directions regarding the
operation and controls of this machine.
2. Make sure the saw is stable.
3. Make sure the blade is mounted correctly and that
Projectiles thrown from the machine
could cause serious eye injury. Wear
safety glasses during assembly and
operation.
the arbor nut is tight.
4. Make sure the fence is parallel to the blade.
5. Make sure the guard assembly is installed, aligned
with the blade, and functional.
6. Make sure the saw blade does not touch the table
insert when it is adjusted to the maximum tilt angle
and height.
To test run the table saw, do these steps:
1. Connect the table saw to the power source.
Loose hair and clothing could get
caught in machinery and cause serious
personal injury. Keep loose clothing
rolled up and long hair tied up and
away from machinery.
2. Face the table saw and stand to the left of the
blade path.
3. Turn the table saw ON.
— The table saw should run smoothly with little or
no vibration; once it does, the machine is ready
for regular operations.
— Immediately turn the table saw OFF if you suspect
any problems, and refer to Page 48 to trouble-
shoot/fix any problems before starting the table
saw again. (If the source of an unusual noise or
vibration is not readily apparent, contact our
technical support for help.)
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
OPERATIONS
General
Table saws will perform many types of operations that are
beyond the scope of this manual. Many of these opera-
tions can be dangerous or deadly if performed incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary knowl-
edge and skills to operate this machine. If at any time
you experience difficulty performing an operation, stop
using the machine!
If you are an inexperienced operator, we strongly recom-
mend that you read books, trade articles, or seek training
from an experienced table saw operator before perform-
ing any unfamiliar operations. Above all, your safety
should come first!
READ and understand this entire instruc-
tion manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
Blade Height
For optimum cutting on through-cuts, raise the blade
height so it protrudes above the workpiece approximately
1
⁄
4" as shown in Figure 32. Ideally, you want 5-7 teeth in
the workpiece during all operations.
Feed Rate
The rate at which you push the workpiece into the mov-
ing blade is extremely important for making safe and
quality cuts. Using improper feed rates for long periods
of time will also decrease the life span of your saw and
blades.
Figure 32. Top of blade protruding
To determine the appropriate feed rate, take into con-
sideration the size of your motor, the thickness of your
workpiece, and the type and sharpness of your blade.
Most of all, listen to the motor and use common sense. If
the motor sounds like it is struggling during a cut, it prob-
ably is. Reduce the feed rate immediately to reduce the
risk of kickback.
approximately 1⁄4" from workpiece.
Generally, more teeth in a cut causes more friction.
Smaller teeth take less of a bite out of the wood than
larger teeth; thus, they need a slower feed. Too much
heat can cause your stock to burn, your blades to wear
out prematurely, and may result in kickback.
-23-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Blade Selection
With all the various kinds of blades available, it would be
beyond the scope of this manual to name every type of
blade and tooth design. However, some basics are impor-
tant to know.
Blade Material
There are two major materials used in circular saw
blades—Carbide and Steel.
Most woodworkers these days prefer carbide-tipped
blades because they can last much longer than steel
blades before they need to be resharpened. Carbide-
tipped blades are also a lot more expensive than steel
blades and require expensive honing equipment to be
sharpened.
Figure 33. Rip blade.
Steel blades can be sharper than carbide-tipped blades
and create less friction during a cut. Since they wear out
so quickly, they are often only used if heat will be a fore-
seeable problem when cutting thick stock. Steel blades
are easy to resharpen and are not as expensive as their
carbide-tipped counterparts.
Blade Types
•
•
•
Rip blades (Figure 33) typically have between 30-40
teeth and provide fast feed rates when making long
cuts along the grain. Rip blades have large teeth for
excellent chip clearance and minimal binding. The
main drawback for rip blades are the rough cuts left
in the stock.
Figure 34. Crosscutting blade.
Crosscutting blades (Figure 34) are designed for
quick, smooth action when making cuts across the
grain. Drawbacks of this type of blade are buildup of
heat, slower feed rates and premature wear of the
blade because the greater number of teeth creates
more friction.
Combination blades (Figure 35) perform both rip-
ping and crosscutting duties well. The blades carry
enough teeth to perform the smooth cutting of a
crosscutting blade and the large gullets of a rip
blade to clear sawdust quickly. Drawbacks of this
type of blade are that they do not perform either
function as well as a dedicated rip or crosscut blade.
Figure 35. Combination blade.
-24-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
•
Plywood blades (Figure 36) have a large number
of teeth, have a thin kerf and create exceptionally
smooth cuts. As the name implies, these types of
blades are excellent for fine plywood and also for
cutting bevels, rabbets or compound miters. The
drawback to this type of blade is the great amount
of heat produced from the many teeth. These blades
should not be used for heavy ripping or cutting thick
stock.
•
Dado blades come in three different types: stack
dadoes, wobble dodoes, and V-dadoes. Dado blades
allow the operator to change kerf sizes and to make
quick and easy non-through cuts. Dado blades are
primarily designed for making dado and rabbet cuts.
The drawback to these type of blades are their high
cost. Figure 37 shows a stack dado blade.
Figure 36. Plywood blade.
Do not use dado blades for through cuts. They are
not designed for through cuts and may cause minor
to moderate personal injury when misused.
Figure 37. Stack dado blade.
Tooth Configuration is another important aspect of blade
design. There are four main types: flat-top grind for fast
heavy-duty ripping; alternate-top bevel for reduced-heat,
tear-out free cuts, and ripping/cutting; alternate-top
bevel and raker for solid and plywood, good all-around,
but not for fine joinery; and triple-chip grind for cutting
hardwoods as well as plastics, particle board and alumi-
num. Figure 38 shows these configurations, along with
their respective kerf profiles.
����
���
������
����
�����
�����
����������
���
�����
�������
���������
���
�����
Changing Blades
To change blades, do these steps:
Figure 38. Tooth configurations.
1. DISCONNECT POWER FROM THE TABLE SAW!
2. Block the blade with a piece of scrap wood, as shown
in Figure 39, and remove the arbor nut and flange.
3. Remove the existing blade.
4. Install the new blade, flange, and arbor nut, mak-
ing sure that the teeth of the blade point toward the
front of the saw.
Figure 39. Using a scrap piece of wood to
aid in tightening/loosening blade. Guard
removed for clarity.
5. Block the blade with the scrap piece of wood and
tighten the arbor nut with the arbor wrench.
-25-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Through vs. Non-Through
Cuts
Understand the safety precautions for each type of cut
to reduce the risk of injury.
The risk of kickback exists with both through and non-
through cuts. Kickback is an event in which the workpiece
is propelled back towards the operator at a high rate of
speed. The risk of kickback is higher with non-through
cuts because the splitter and blade guard must be
removed. Always remember to re-install the blade guard
and splitter after performing a non-through cut.
Through Cuts
A through cut is a sawing operation in which the
workpiece is completely sawn through. Rip cuts, cross
cuts, miter cuts, and angled cuts are all through cutting
operations.
DO NOT make a through-cut with a dado
blade. Dado blades are not designed
for through cuts. Failure to follow this
warning could result in serious per-
sonal injury.
Safety precautions and instructions for through cuts
are located on the following pages:
Rip Cuts: Page 27
Cross Cuts: Page 28
Miter Cuts: Page 28
Blade Tilt/Bevel Cuts: Page 27
Non-Through Cuts
A non-through cut is a sawing operation where the blade
does not protrude above the top face of the wood stock.
Non-through cuts require the removal of the blade guard
and splitter. Dado cuts, rabbet cuts, and resawing are
the only non-through cuts that can be performed with
this table saw. Always replace the blade guard after non-
through cuts!
The blade guard/splitter is a critical
safety device that greatly reduces
operator risk of injury. The blade guard
MUST be re-installed after making non-
through cuts.
Safety precautions and instructions for through cuts
are located on the following pages:
Dado Cuts: Page 29
Rabbet Cuts: Page 31
Resawing: Page 33
-26-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Rip Cuts
Rip cuts or "Ripping" means cutting with the grain of the
workpiece. In other materials such as MDF or plywood,
ripping simply means cutting lengthwise.
Serious injury can be caused by
kickback. Kickback is a high-speed
expulsion of stock from the tablesaw
toward an operator. The operator or
bystanders may be struck by flying
stock, or the operator’s hands can
be pulled into the blade during the
kickback.
To make a rip cut, do these steps:
1. Review Preventing Kickback on Page 11 and take
the necessary precautions to prevent kickback.
2. Joint one long edge of the workpiece on a jointer.
3. DISCONNECT THE SAW FROM POWER!
4. Use the scale to set the fence to the desired width
of cut.
5. Adjust the blade height so the teeth protrude
approximately 1⁄4" above the workpiece.
6. Set up safety devices such as featherboards or other
anti-kickback devices.
Figure 40. Typical rip cut.
7. Rotate the blade to make sure it does not come into
contact with any of the safety devices.
8. Plug the saw into the power source, turn it ON, and
allow it to reach full speed.
9. The jointed edge of the workpiece must slide against
the fence during the cutting operation.
10. Using a push stick, feed the workpiece through
the saw blade, as shown in Figure 40, until the
workpiece is completely past the saw blade.
Figure 41. Blade tilted to 45° (guard
removed for photo clarity).
Blade Tilt/Bevel Cuts
The blade can tilt anywhere between 0° and 45°, and
the blade guard tilts with the blade. Figure 41 shows an
example of the blade when tilted to 45°, and Figure 42
shows and example of a typical 45° rip cut.
When using the tilting mechanism:
•
•
•
Never tilt the blade while it is moving.
Slow your feed rate down.
Make sure the blade does not touch the table insert
before starting the saw.
Figure 42. Typical 45° rip cut.
-27-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Cross Cuts
Cross Cuts or "Crosscutting" means cutting across the grain
of the workpiece. In MDF or particleboard, crosscutting is
cutting across the width of the workpiece.
Serious injury can be caused by
kickback. Kickback is a high-speed
expulsion of stock from the tablesaw
toward an operator. The operator or
bystanders may be struck by flying
stock, or the operator’s hands can
be pulled into the blade during the
kickback.
To crosscut using the miter gauge, do these steps:
1. DISCONNECT THE SAW FROM POWER!
2. Remove the rip fence and position the miter gauge,
adjusted to 90°, in a miter slot.
3. Adjust the blade height so the teeth protrude
approximately 1⁄4" above the workpiece.
4. Slide the miter gauge near the blade and adjust the
workpiece so the blade will cut on the waste side of
the line.
5. Plug in the tablesaw, turn it ON, and allow it to
reach full speed.
6. Hold the workpiece firmly against the face of the
miter gauge and ease it into the blade as shown in
Figure 43.
Figure 43. Typical cross cut.
Miter Cuts
A miter is an angled crosscut. Miters are usually cut in the
same manner as 90˚ crosscuts, using the miter gauge and
a predetermined mark on the workpiece.
To cut a miter, do these steps:
1. Determine the angle of your cut and mark it across
your workpiece.
Tip: A correctly calibrated miter gauge makes mark-
ing angles easy. Place the face of the miter gauge
against the edge of the workpiece, so the bar goes
across the face of the workpiece, and use the bar as
a guide (see Figure 44) to pencil in your cut.
Figure 44. Using the miter gauge to mark
the angle of a miter cut.
2. With miter gauge in the table slot, hold the
workpiece against the miter gauge body and align
the mark to the blade.
3. Make the cut in the same manner as described in the
Cross Cuts instructions.
-28-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Dado Cuts
Commonly used in furniture joinery, a dado is a straight
channel cut in the face of the workpiece. Dadoes can be
cut using either a dedicated dado blade or a standard saw
blade.
The danger of kickback increases rela-
tive to the depth and width of a cut.
Reduce the risk of kickback by making
multiple passes to achieve the desired
depth of cut. Failure to follow these
warnings could result in serious per-
sonal injury.
The table saw motor may be pushed to its limits when
making a dado cut. If the motor starts to bog down, slow
down your feed rate.
To use a stacked or wobble dado blade, do these steps:
1. DISCONNECT THE SAW FROM POWER!
2. Remove the table insert, the blade guard, and the
saw blade.
3. Attach and adjust the dado blade system according
to the dado blade manufacturer’s instructions, then
install the table insert for dado blades.
4. Raise the dado blade up to the desired depth of cut
(depth of dado channel desired). When cutting deep
dadoes, take more than one pass to reduce the risk
of kickback.
5. Adjust the fence as necessary to align the blade with
the desired location of the dado.
6. Reconnect the power and cut the dado.
Note: When dadoing across a workpiece, use the
miter gauge and carefully line up the desired cut
with the dado blade. DO NOT use the fence in com-
bination with the miter gauge.
Figure 45. Dado cut.
DO NOT make a through-cut with
a dado blade. Dado blades are not
designed for through cuts. Failure to
follow this warning could result in seri-
ous personal injury.
Dado operations require proper pro-
cedures to avoid serious injury. Extra
care must be taken to prevent kick-
back when using dado blades. Any
movement of the workpiece away
from the fence will cause kickback. Be
certain that stock is flat and straight.
Failure to follow these warnings could
result in serious personal injury.
-29-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
To cut dadoes with a standard blade, do these steps:
�����
Note: Reduce motor overloading and blade wear by using
a ripping blade. Ripping blades are designed to clear the
sawdust quickly. Refer to Page 24 for more details.
���������
1. DISCONNECT THE SAW FROM POWER!
���������
2. Mark the width of the dado cut on the workpiece.
Include marks on the edge of the workpiece so the
cut path can be aligned when the workpiece is lying
on the table.
3. Raise the blade up to the desired depth of cut
(depth of dado channel desired). When cutting deep
dadoes, take more than one pass to reduce the risk
of kickback.
Figure 46. First cut when making a dado
with a standard ripping blade.
4. If dadoing across the workpiece, use the miter gauge
to support the workpiece, and align the blade to cut
one of the dado sides. DO NOT use the fence in com-
bination with the miter gauge.
�����
���������
���������
5. If dadoing the length of a workpiece, align the blade
to cut one of the dado sides as shown in Figure 46.
6. Reconnect the saw to the power source and turn the
saw ON. Allow the blade to reach full speed.
7. Perform the cutting operation.
8. Re-adjust the fence so the blade is aligned with the
other edge of the intended dado channel (Figure
47).
Figure 47. Second cut when making a
dado with a standard ripping blade.
Note: Be sure to keep the cuts within your marks;
otherwise, the dado will be too big.
9. Continue making cuts toward the center of the dado
until the dado is complete.
-30-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Rabbet Cuts
Commonly used in furniture joinery, a rabbet is an L-
shaped groove cut in the edge of the workpiece. Rabbets
can be cut with either a dado blade or a standard saw
blade.
Serious injury can be caused by
kickback. Kickback is a high-speed
expulsion of stock from the tablesaw
toward an operator. The operator or
bystanders may be struck by flying
stock, or the operator’s hands can
be pulled into the blade during the
kickback.
Rabbet cutting on the edge of the workpiece requires a
sacrificial fence attachment (Figure 48). Make the sacri-
ficial fence the same length as the fence and 3⁄4" thick.
Attach it to the fence with screws or clamps, making sure
they are all secure and tight. With the saw turned ON,
raise the blade into the sacrificial fence to the height
needed.
To cut rabbets with the dado blade, do these steps:
���������
1. DISCONNECT THE SAW FROM POWER!
�����������������
�����������
2. Adjust the dado blade to the height needed for the
rabbeting operation. When cutting deep rabbets,
take more than one pass to reduce the risk of kick-
back.
�������������
3. Adjust the fence and align the workpiece to perform
the cutting operation as shown in Figure 49.
Figure 48. Sacrificial fence setup.
4. Reconnect the saw to the power source and turn the
saw ON.
�����������������
�����
5. When the blade has reached full speed, perform a
test cut with a scrap piece of wood.
6. If the cut is satisfactory, repeat the cut with the
���������
����������
final workpiece.
Figure 49. Rabbet cutting with a dado
blade.
-31-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Cutting rabbets with a standard saw blade DOES NOT
require the use of a sacrificial fence. Reduce motor over-
loading and blade wear by using a ripping blade. Ripping
blades are designed to clear the sawdust quickly.
�����
���������
���������
To cut rabbets with the standard blade, do these steps:
1. DISCONNECT THE SAW FROM POWER!
2. Clearly mark the width of the rabbet cut on the
workpiece.
Note: Include marks on the edge of the workpiece
to clearly identify the intended cut while it is laying
flat on the saw table.
Figure 50. First cut when rabbet cutting
with a standard rip blade.
3. Raise the blade up to the desired depth of cut
(depth of rabbet channel desired). When cutting
deep rabbets, take more than one pass to reduce
the risk of kickback.
�����
���������
4. Adjust the fence so the blade is aligned with the
inside of your rabbet channel as shown in Figure 50.
5. Stand the workpiece on edge as shown in Figure 51,
and adjust the saw blade height to intersect with
the first cut.
���������
6. Perform the second cut to complete the rabbet.
Figure 51. Second cut when rabbet cutting
with a standard rip blade.
-32-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Resawing
Resawing is the process of cutting a thick piece of stock
into one or more thinner pieces. Bandsaws are ideal for
resawing and the process is fairly easy and safe. A table
saw is not intended for resawing and the process is diffi-
cult and extremely dangerous. Resawing on the table saw
often binds the blade, causing kickback. The risk of kick-
back increases relative to the depth of a cut. Kickback is
more dangerous when resawing on a table saw because
the anti-kickback devices and blade guard must be
removed, leaving no protection between your hands and
the saw blade. Kickback can pull the operator's hands into
the blade, or the operator or bystanders may be hit by
flying stock. DO NOT resaw on a table saw without using
a resaw barrier. DO NOT resaw on a table saw without
wearing a full face shield.
Resawing operations require proper
procedures to avoid serious injury.
Extra care must be taken to prevent
kickback when resawing. Any tilting
or movement of the workpiece away
from the fence will cause kickback. Be
certain that stock is flat and straight.
Failure to follow these warnings could
result in serious personal injury.
Resawing on a table saw increases the
chances of kickback. Serious injury
can be caused by kickback. Kickback
is a high-speed expulsion of stock
from the tablesaw toward an opera-
tor. The operator or bystanders may
be struck by flying stock, or the
operator’s hands can be pulled into
the blade during the kickback.
The following instructions describe how to build a resaw
barrier, add an auxiliary fence to your standard fence,
and safely perform resawing operations.
Note: This table saw can only resaw wood that is less
than 6" tall.
Resaw Barrier
The resaw barrier shown in Figure 52 holds the workpiece
vertical, keeps the workpiece aligned with the fence, and
keeps your hands away from the blade.
Components Needed for the Resaw Barrier:
Hardwood or Plywood 3⁄4" x 51⁄2" x 27" .....................1
Hardwood or Plywood 3⁄4" x 3" x 27" ........................1
Wood Screws 2" ................................................8
Wood Glue ........................................... As Needed
Tools Needed for the Resaw Barrier:
Table Saw ........................................................1
Jointer and Planer............................. Recommended
Clamps................................................2 Minimum
Drill and Drill Bits...............................................1
Figure 52. Resaw barrier.
To build the resaw barrier, do these steps:
1. Cut two boards to 3⁄4" x 51⁄2" x 27" and 3⁄4" x 3" x
27". If you are using hardwood, cut the boards over-
size, then joint and plane the boards to the correct
size to make sure the boards are square and flat.
Note: Only use furniture grade plywood or kiln dried
hardwood to prevent warping.
-33-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
2. Pre-drill and countersink 8 holes approximately 3⁄8
"
from the bottom of the 51⁄2" tall board.
3. Glue the end of the 3" board, then clamp the boards
at a 90° angle with the larger board in the vertical
position as shown in Figure 53.
4. Secure the joint with the wood screws.
Auxiliary Fence
The auxiliary fence is necessary if you are resawing wood
that is more than 3" tall. It should be no less than 1⁄2
shorter than the board to be resawn.
"
Components Needed for the Auxiliary Fence:
Hardwood or Plywood 3⁄4" x (Height) x 27".................1
Flat Head Screws 1⁄4-20" x 1" .................................8
Hex Nuts 1⁄4-20".................................................8
Figure 53. Clamping the resawing barrier.
Tools Needed for the Resaw Barrier:
Table Saw ........................................................1
Jointer and Planer............................. Recommended
Clamps................................................2 Minimum
Drilland Drill Bits ...............................................1
To build the auxiliary fence, do these steps:
1. Cut a 3⁄4" thick board 27" long, then cut it no less
than 1⁄2" shorter than the board to be resawn. If
you are using hardwood, cut the board oversize,
then joint and plane the board to the correct size to
make sure the board is square and flat.
Note: Only use furniture grade plywood or kiln dried
hardwood to prevent warping.
2. Pre-drill and countersink 8 holes 11⁄4" from the bot-
tom of the board.
3. Pull an end cap off of the standard fence, then slide
the hex nuts into the T-slot and replace the end cap.
4. Thread the flat head screws through the auxiliary
fence and into the hex nuts in the standard fence,
and tighten securely as shown in Figure 54.
Figure 54. Auxiliary fence.
-34-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Resawing Operations
Resawing pushes a table saw to its limits. If the motor
bogs down when resawing, slow down your feed rate.
Also, use a ripping blade when resawing to reduce motor
overloading and blade wear. Ripping blades are designed
to clear the sawdust quickly.
You may experience kickback during
this procedure. Stand to the side of the
blade and wear a full face shield to pre-
vent injury when resawing.
Components Needed for Resawing:
Zero Clearance Insert ..........................................1
Ripping Blade 10" ...............................................1
Clamps............................................................2
Shop Made Auxiliary Fence....................................1
Shop Made Resaw Barrier......................................1
Always use push sticks or push paddles
to increase safety and control during
operations which require that the blade
guard and splitter be removed from the
saw. ALWAYS replace the blade guard
after resawing is complete.
To perform resawing operations, do these steps:
1. DISCONNECT THE SAW FROM POWER!
2. Remove the table insert and the blade guard/split-
ter, install a ripping blade and a zero clearance
table insert, and lower the blade below the table
surface.
The danger of kickback increases rela-
tive to the depth of a cut. Reduce the
risk of kickback by making multiple
passes to achieve the desired depth of
cut. Failure to follow these warnings
could result in serious personal injury.
3. Attach the auxiliary fence to the standard fence
and set it to the desired width. Note: Account for
blade kerf, the rough cut made by the blade, and
the inaccuracy of the fence scale when the auxil-
iary fence is installed when figuring out the correct
width.
4. Place the workpiece against the fence, slide the
resaw barrier against the workpiece, and clamp the
resaw barrier to the table top (see Figure 55).
���������
���������
�����
�����
�����
�������
5. Slide the workpiece over the blade to make sure it
moves smoothly.
���������������
6. Raise the blade approximately an inch, or close to
half the height of the workpiece, whichever is less.
7. Plug in the table saw, turn it ON, and use a push
stick to feed the workpiece through the blade using
a slow, steady feed rate.
Figure 55. Completed resaw cut.
8. Flip the workpiece end for end, keeping the same
side against the fence, and run the workpiece
through the blade.
9. Turn OFF the table saw, then separate the parts of
the workpiece and hand plane the remaining ridge.
10. When finished resawing, remove the resaw barrier
and re-install the blade guard/splitter.
-35-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Aftermarket Safety
Accessories
Besides making your table saw experience more
enjoyable, aftermarket or shop-made safety acces-
sories can greatly increase your personal safety,
and allow you to make difficult cuts with your table
saw that you would not otherwise be able to make.
Here are some basic aftermarket items you might
want to consider:
Figure 56. Outfeed roller table.
•
A Roller Table (shown in Figure 56) or Roller
Stand is designed to catch long boards dur-
ing and after a cut. These accessories let the
board easily glide off the saw table without
causing a height difference. At the very least,
a work table should be used for this same pur-
pose. If a long piece of stock teeters over the
edge of the table during a cut, a kickback may
occur.
•
•
Anti-Kickback Devices like the Boardbuddies®
shown in Figure 57 only allow the workpiece
to move in one direction. If a kickback does
occur, the wheels lock in place to stop or slow
the movement of the workpiece.
Hold-Down Jigs similar to the Right Angle Jig®
shown in Figure 58 allow the user to stabilize
a cut beyond ordinary means. This is crucial
for difficult cuts. Notice in Figure 58 that the
cut being performed would be extremely dan-
gerous if the operator was using the rip fence.
Other cuts, like vertical dadoes, would also be
extremely difficult and dangerous without the
use of similar devices.
Figure 57. Anti-kickback devices.
•
Push Sticks and Push Paddles help keep your
hand away from the moving blade. They also
act as a barrier between your hand and the
workpiece in the event of a kickback. These
devices come in many different sizes and
shapes. Pick those that offer safety and stabil-
ity without sacrificing comfort and grip.
Figure 58. Hold-down jig.
-36-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Shop-Made Safety
Accessories
Shop-made safety accessories are another source of
devices to use to increase your safety while oper-
ating the table saw. When care is taken with the
setup and design, shop-made tools can be an invalu-
able resource for making the safest cuts possible.
Here are some of the basic items you may want
to consider:
•
Push Sticks made from the shop are very popu-
lar among table saw owners because they are
inexpensive and easy to make. Particularly
good are those that keep your hand a safe
distance away from the blade, offer stable
support and grip, and are comfortable in the
hand. Figure 59 shows an illustration of a sim-
ple push stick.
Figure 59. Illustration of a simple push stick.
•
•
Featherboards similar to the one in Figure
60 make good anti-kickback devices. To use
these, they must be clamped to the table or
fence. The angled ends and flexibility of the
fingers allow the workpiece to move in one
direction and lock up if the workpiece moves
backwards.
Zero-Clearance Table Inserts can be pur-
chased or made from wood and substituted
for the factory inserts. The advantage in these
devices is that there will only be as much
space between the blade and the insert as the
blade requires. Many woodworkers have a dif-
ferent insert for different heights and blades.
Zero-clearance table inserts result in clean
cuts with less tear-out and a reduced chance
that a small piece of stock will be pulled down
inside the saw or will be kicked back. Figure
61 shows an example of a “blank” zero-clear-
ance insert. When making a zero-clearance
table insert, never hold the insert in place
with your hands or try to lower the insert onto
a moving blade. Hold or clamp the insert to
the table with a sacrificial board, and use a
smaller diameter blade to plunge the initial
cut through the insert.
Figure 60. Anti-kickback featherboard.
Figure 61. Zero-clearance table insert.
-37-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
MAINTENANCE
V-Belts
The V-belts may stretch a little as the saw is used and
may need to be tightened from time to time. Replacing
the V-belts is not much harder than tightening them, but
you must make sure you replace the V-belts with a match-
ing set.
Cleaning
MAKE SURE that your machine is
unplugged during all maintenance pro-
cedures! If this warning is ignored, seri-
ous personal injury may occur.
Frequently blow-off dust with compressed air. Dust build-
up around the motor and internal working parts will
decrease the saw's life span.
Occasionally it will become necessary to clean the inter-
nal parts with more than compressed air. To do this,
remove the table top and clean the internal parts with a
citrus cleaner or mineral spirits and a stiff wire brush or
steel wool. If any essential lubrication is removed during
cleaning, relubricate those areas.
Table & Base
Tables can be kept rust-free with regular applications of a
quality metal protectant/lubricant.
Lubrication
Since all bearings are sealed and permanently lubricated,
simply leave them alone until they need to be replaced.
Do not lubricate them.
Lubricate the following areas every six to twelve
months according to frequency of use:
•
•
•
Blade angling trunnions. These should be lubricated
with 6 or 7 drops of light machine oil.
Blade height trunnion. This should also be lubricat-
ed with 6 or 7 drops of light machine oil.
The two worm gears should be lubricated with
either graphite or white lithium grease.
Figure 62. Lubrication points.
-38-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
SERVICE
General
This section covers the most common service adjustments
or procedures that may need to be made during the life
of your machine.
If you require additional machine service not included
in this section, please contact Woodstock International
Technical Support at (360) 734-3482 or send e-mail to:
MAKE SURE that your machine is
unplugged during all service proce-
dures! If this warning is ignored, seri-
ous personal injury may occur.
Blade Tilt Stop Bolts
The table saw trunnion features 45° and 90° stop bolts on
the geared trunnion that, when adjusted correctly, stop
the blade exactly at 45° and 90° during blade adjust-
ments.
�������������
To set the stop bolts on the trunnion, do these steps:
1. DISCONNECT SAW FROM POWER!
2. Position the blade tilt to zero (see indicator on the
front of the saw), and raise the blade several inches
above the table.
�������������
3. Place a machinist’s square flat on the table and
slide it alongside the blade. The square should con-
tact the blade evenly from bottom to top. Make sure
that a blade tooth does not obstruct the movement
of the square.
Figure 63. Blade tilt stop bolts.
4. Adjust the handwheel until the square is flush with
the blade. Loosen the tilt indicator arrow, set to
zero, and retighten. Loosen and adjust the stop bolt
on the left side of the front trunnion to allow a 90°
stop point. Refer to Figure 63 for details.
5. Turn the blade angle handwheel until the angle indi-
cator points at the desired angle.
6. Tighten the handwheel locking knob.
7. Repeat Steps 1-6 for setting the blade to 45° and
adjust the 45° stop bolt on the right side of the
front trunnion. Use the 45° side of a combo square
or a bevel gauge set at 45°.
-39-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Blade Alignment
If the blade touches the table insert when you raise
and lower it, then the table needs to be shifted where
it mounts to the cabinet. If you do this and the blade
still needs to be adjusted, the trunnion assembly can be
adjusted inside the cabinet so the blade is repositioned.
The table and wings are very heavy
and may cause injury while lifting. Get
help when lifting to reduce the risk of
injury.
To adjust the trunnion assembly, do these steps:
1. DISCONNECT SAW FROM POWER SOURCE!
2. Get another person to help you remove the table
and wings.
NOTICE
3. The first option is to loosen the trunnion assembly
mounting bolts shown in Figure 64 and then shift
the entire trunnion assembly in the appropriate
direction. Tighten the trunnion assembly mounting
bolts.
If you move the blade position, make
sure to align blade splitter and check
the miter slot-to-blade alignment.
4. Place the table back on the cabinet and install the
table mounting bolts without tightening completely.
Check the blade position relative to the table insert.
If further adjustments are needed, try to do so by
shifting the table.
Finally, if the above adjustments do not resolve the blade
alignment situation, you need to adjust the geared bear-
ing housing shown in Figure 65.
To adjust the geared bearing housing, do these steps:
1. Get another person to help you remove the table
and wings, and then loosen the blade adjustment
bolt shown in Figure 65.
Figure 64. Trunnion assembly mounting
bolts.
2. Slide the geared bearing housing in the appropriate
direction, according to the blade position.
Geared Bearing
Housing
3. Place the blade on the arbor and finger tighten the
arbor nut to make sure the blade does not touch any
of the internal parts of the saw.
Blade Adjustment Bolt
4. Remove the blade and tighten the blade adjustment
bolt.
5. Replace the table, the wings, and the table insert.
Tighten these securely. Install the blade on the saw
and tighten the arbor nut.
Figure 65. Lower wheel adjustment
control.
-40-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
6. Raise the blade and check its position in the table
insert opening. If the blade position is not satisfac-
tory, make sure you have correctly shifted the com-
ponents discussed in this section. If you repeat these
steps and still cannot get favorable results, call our
Technical Support.
Miter Slot Parallel to
Blade
To cut accurately when using the miter gauge, the miter
slot MUST be parallel to the blade.
To check and adjust the miter slot parallel to the blade,
do these steps:
1. DISCONNECT SAW FROM POWER SOURCE!
2. Raise the blade to its full height and set the blade
90˚ to the table.
3. Use an adjustable square to measure the distance
from the miter slot to a carbide tip on the blade as
shown in Figure 66. Make sure that the face of the
adjustable square is even along the miter slot.
Figure 66. Measuring blade to miter slot.
4. With the end of the adjustable square just touching
the tip, lock the square in place. Now, mark the car-
bide tip with a magic marker where you made this
measurement.
5. Rotate that tip to the other end of the table insert.
6. Slide the adjustable square down to the other end
of the table insert, and compare the distance from
the marked blade tip to the end of the adjustable
square.
7. If the blade tip does not touch the end of the adjust-
able square similar to the first measurement, then
the table will need to be adjusted.
Figure 67. Table mounting locations.
8. To adjust the table, loosen the four bolts at the
table mounting locations shown in Figure 67.
-41-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
9. Slightly rotate the table in the appropriate direction.
Recheck the measurements you did in Steps 3 & 6.
�������������������
��
������
��
10. When you have adjusted the table so both measure-
ments are the same, tilt the blade to 45˚ and mea-
sure the distance from the miter slot to the blade as
done in Steps 2–5.
�����
— If these measurements are the same, tighten the
table mounting bolts, then recheck to make sure
the table did not move during tightening. No fur-
ther adjustments are necessary.
�
��
��
— If either of these measurements are different from
the other, then the table needs to be shimmed
with metal shim stock at the table mounting loca-
tions. Proceed to the next step.
Figure 68. Measuring blade to miter slot
at point A.
11. First determine which measurement is longer. If
measurement “A” (Figure 68) is shorter, then cor-
ners #1 and #2 need to be shimmed.
�������������������
������
��
��
12. If measurement “B” (Figure 69) is shorter, then cor-
ners #3 and #4 need to be shimmed.
�����
��
13. Place equal sized pieces of metal shim stock under
each of the corners that need to be shimmed.
Repeat this until the distance from the miter slot to
the blade is equal at both the front and back.
�
��
14. Set the blade to 90˚ and make sure the miter slot is
still parallel to the blade.
Figure 69. Measuring blade to miter slot
at point B.
15. Tighten the table mounting bolts and recheck mea-
surements. Adjust if necessary.
Shimming Wings
To shim an extension wing, do these steps:
1. DISCONNECT SAW FROM POWER SOURCE!
2. Remove the extension wing from the table.
Masking Tape
3. If the extension wing tilts up, place a few layers of
tape above the wing mounting bolt holes as shown
in Figure 70. If the extension wing tilts down, place
the tape below the bolt holes.
Figure 70. Shimming table with masking
tape.
4. Reinstall the extension wing on the table, trim any
projecting tape, and check to see if the table is flat.
Repeat as necessary until the extension wing creates
one flat surface with the main table.
-42-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Splitter Adjustment
To adjust the blade splitter square to the table, do
these steps:
Adjustment Bolts
1. DISCONNECT SAW FROM POWER SOURCE!
2. Loosen the set screws shown in Figure 71 to allow
Front Splitter Bracket
the blade splitter to rotate on the support shaft.
3. Use a try square to adjust the blade splitter 90˚ to
the table as shown in Figure 72. Tighten the set
screws to lock the splitter in place.
To check and align the splitter to the blade, do these
steps
Set Screws
Figure 71. Splitter attachment locations.
1. DISCONNECT SAW FROM POWER SOURCE!
2. Raise the blade to its maximum height. With a
straightedge, check to make sure that the blade
splitter is in-line with the blade, similar to Figure 29
on Page 21. If it is, tighten the adjustment bolts on
the splitter bracket. If it is not, you need to realign
the splitter to the blade
3. To align the splitter to the blade, loosen the two
adjustment bolts shown in Figure 73 and the two
adjustment bolts on the bracket that attaches the
front of the splitter shown in Figure 71.
4. Align the blade and splitter so they both evenly
touch the straightedge. Tighten all the adjusting
bolts to secure the splitter in place.
Figure 72. Squaring splitter to table.
The blade splitter MUST be installed and aligned with
the blade before cutting, or the risk of kickback will be
greatly increased and severe injury may occur. If you
cannot get the blade splitter aligned with the blade,
call our Technical Support for help.
Adjustment Bolts
Figure 73. Aligning splitter to blade.
-43-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Angle Pointer
The angle pointer allows you to set the angle to the cor-
rect position on the angle gauge after setting the 90˚ and
45˚ angles.
To set the angle pointer, do these steps:
1. Make sure that you have performed the 90˚ and 45˚
instructions in the Blade Tilt Stop Bolts section on
Page 39 before beginning.
2. Turn the blade to 90˚.
3. Check the angle pointer. If it reads “0”, then it is
already adjusted correctly.
Figure 74. Blade tilt pointer.
4. If it is not pointing to “0”, then loosen the adjust-
ment screw shown in Figure 74. Set the pointer to
the “0” then tighten the adjustment screw.
Miter Gauge
The miter gauge (shown in Figure 75) allows you to sup-
port the workpiece while crosscutting. In order to be
accurate, the miter gauge pointer needs to be adjusted
before use.
Adjustment Knob
Figure 75. Miter gauge.
NOTICE
To set the miter gauge pointer, do these steps:
1. Loosen the adjustment knob shown in Figure 75, so
the miter gauge rotates back and forth.
2. Using a square, adjust the miter body so it is square
to the miter bar.
If the miter bar fits too loose in the
miter slot, it can be adjusted by tight-
ening the set screws on the side of the
miter slide. These set screws push the
thin walls of the slide out slightly to
create resistance while in the miter
slot. Do not overtighten.
3. Tighten the knob so the miter body is secure.
4. Loosen the setscrew on the miter slide next to the
angle pointer, and adjust the angle pointer so it
reads “0”. Tighten the nut so the angle pointer is
secure.
5. Check and adjust if necessary.
-44-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Replacing V-Belts
The V-belts are tensioned by pivoting the motor up or
down. The slotted holes in the motor mount bracket
(Figure 76) allow the motor to pivot in the hinge holes.
�������������
To replace the V-belts, do these steps:
1. DISCONNECT SAW FROM POWER SOURCE!
2. Loosen the motor mount bolts.
3. Pivot the motor up so the belts loosen, then remove
them from the pulleys.
�����������
4. Install a matching set of new V-belts.
Figure 76. Motor mount anatomy.
5. Pivot the motor down to tighten the belts, and hold
downward pressure on the motor with one hand and
tighten the motor mount bolts with the other hand.
������
6. Check the belt tension by pushing (with moderate
pressure) one of the belts between the pulleys, as
shown in Figure 77. The correct deflection range is
between 1⁄4" and 1⁄2".
����������
Note: V-belts only need to be tight enough so they
don't slip when the motor is at full load. Extremely
tight V-belts will cause the motor and pulley bear-
ings to wear faster.
������
Figure 77. Checking V-belt deflection to
Adjusting Fence
ensure correct tension.
The adjustment set screws shown in Figure 78 allow you
to pivot the fence left or right to make it parallel with
the blade. The fence must be parallel to the blade or
slightly (no more than 1⁄32" from front to back) angled
away from the blade at the rear of the fence so the
workpiece will not bind between the fence and blade
during the cut.
Close Up View
of Adjustment
Mechanism
If your workpiece binds as you make your cuts, the risk
of serious personal injury from kickback increases dra-
matically. Signs that the workpiece is binding include
burn marks on the workpiece and difficulty feeding the
workpiece completely through the cut.
Adjustment
Set Screws
The basic procedure for adjusting the fence is to tighten
one side and loosen the other side in equal increments.
The side that is loosened is the side that the fence will
move toward. For full instructions on adjusting the fence,
refer to the Owner's Manual included with the fence.
Figure 78. Fence adjustment controls.
-45-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
W1677 Wiring Diagram
�������
�������
������
���
���
����������
����������������
��������
������
���������
�
����
����
����
�
���������
����
����
����
�
�
�������
��������
�����
��
��
���
���
���
��
��
��
��
�����
���
���������
������
������
�������
����
������
���� ������ ������� ������ ����� ���
�������� ��� ���� ����� ��� ����������
�����������������������������������
���� ������� ��� ��������� ���� ������
�������������������������
-46-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
W1711 Wiring Diagram
�������
�������
������
���
�
�
�
���
����������
����������������
��������
������
���������
�
����
����
����
����
���������
����
����
����
����
�
�������
��������
�����
��
���
���
���
��
��
��
��
��
������
�����
���
���������
������
������
�������
����
���
������
���������
�����
������
���� ������ ������� ������ ����� ���
�������� ��� ���� ����� ��� ����������
�����������������������������������
���� ������� ��� ��������� ���� ������
�������������������������
-47-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Troubleshooting
This section covers the most common problems and corrections with this type of
machine. WARNING! DO NOT make any adjustments until power is disconnected and
moving parts have come to a complete stop!
Motor & Electrical
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Machine does not
start or a breaker
trips.
1. Plug or receptacle is at fault or wired
incorrectly.
1. Test power plug and receptacle for good
contact and correct wiring.
2. Cable or wiring is open or has high resistance. 2. Troubleshoot wires for internal or external
breaks, and disconnected or corroded
connections; repair or replace wiring.
3. The thermal overload relay below the motor
contactor is tripped.
3. Reset overload relay. If it continues to
trip, turn up the dial to a higher shut-off
amperage.
4. Wall fuse or circuit breaker is blown or
tripped.
4. Make sure circuit breaker/fuse is sized
correctly for machine load or replace weak
breaker.
5. Motor connection is wired incorrectly.
5. Correct motor wiring.
6. Power supply is faulty, or is switched OFF.
6. Make sure all hot lines and grounds are
operational and have correct voltage.
7. Start capacitor is faulty.
8. Motor ON button.
7. Replace start capacitor.
8. Replace faulty ON button.
9. Adjust or repair centrifugal switch.
10. Replace contactor.
9. Centrifugal switch is at fault.
10. Contactor not getting energized or has burnt
contacts.
11. Motor is damaged.
11. Repair or replace motor.
Machine stalls or is
underpowered.
1. Applying too much pressure to workpiece.
2. Low power supply voltage.
1. Use sharp blade, and reduce the feed rate.
2. Make sure all hot lines and grounds are
operational and have correct voltage.
3. Belt is slipping.
3. Replace belt and/or re-tension (Page 45).
4. Plug or receptacle is at fault.
4. Test power plug and receptacle for good
contact and correct wiring.
5. Motor connection is wired incorrectly.
6. Pulley or sprocket is slipping on shaft.
7. Motor has overheated.
5. Correct motor wiring.
6. Replace loose pulley and shaft.
7. Let motor cool, clean motor fan cover, and
reduce workload on machine.
8. Motor bearings are at fault.
8. Rotate motor shaft for noisy or burnt
bearings, replace as required.
9. Run capacitor is faulty.
9. Replace run capacitor.
10. Replace contactor.
10. Contactor not getting energized or has poor
contacts.
11. Motor is at fault.
11. Repair or replace motor.
12. Centrifugal switch is at fault.
12. Repair or replace centrifugal switch.
-48-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Machine has vibra-
tion or noisy opera-
tion.
1. Loose arbor nut.
1. Tighten the arbor nut.
2. Blade is damaged.
2. Replace warped, bent, or twisted blade.
3. Use blade stabilizers.
3. Blade is too thin.
4. Machine is sitting on an uneven floor.
5. Belt is worn or is loose.
6. Pulley is loose.
4. Relocate machine or shim feet.
5. Inspect belt, replace or re-tension (Page 45).
6. Remove pulley; replace shaft, pulley, and set
screw as required, and re-align.
7. Wrong workpiece material (wood).
8. Cast iron motor mount is damaged.
7. Only cut wood with correct moisture content,
with no pitch, glues, or resins.
8. Carefully using leverage and a small pry bar,
carefully look for loose/broken mounts and
replace if necessary.
9. Arbor bearings are damaged.
10. Motor bearings are damaged.
9. Replace arbor housing bearings.
10. Replace motor bearings.
Table Saw Operations
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
Blade is not aligned 1. Blade is warped.
with miter slot or
fence.
1. Replace blade.
2. Blade is not parallel to table top.
2. Adjust table top (miter slot) parallel to blade
(Page 41) or adjust blade parallel to table
(Page 40).
3. Fence is not parallel to blade.
3. Make fence parallel to blade (Page 45).
1. Raise front rail.
Fence hits table top 1. Front rail is bolted too low on table.
when sliding.
2. Rear rail is bolted too low on the table.
2. Raise rear rail.
Blade does not reach 1. 90° stop bolt is out of adjustment.
90°.
1. Adjust 90° stop bolt (Page 39).
2. Pointer bracket is hitting before the blade 2. File down the right side of the pointer bracket
reaches 90°.
3. Sawdust loaded up on positive stop.
until the blade can reach 90°.
3. Clean sawdust off positive stop.
Blade hits insert at 1. Hole in insert is inadequate.
1. File or mill the hole in the insert.
45°.
2. Table out of alignment.
2. Adjust table top (miter slot) parallel to blade
(Page 41) or adjust blade parallel to table
(Page 40).
3. Blade position is incorrect.
3. Adjust blade position.
Blade will not go 1. Table top too low.
1. Raise table by shimming w/washers.
beneath table sur-
face.
Board
binds
or 1. Dull blade.
1. Replace blade (Page 25).
burns when feeding
through tablesaw.
2. Blade is warped.
2. Replace blade (Page 25).
3. Splitter out of alignment.
4. Fence is not parallel to blade.
5. Table top is not parallel to blade.
3. Align the splitter with the blade (Page 43).
4. Make fence parallel to blade (Page 45).
5. Adjust table top (miter slot) parallel to blade
(Page 41) or adjust blade parallel to table
(Page 40).
-49-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
PARTS
Table/Body Breakdown
���
-50-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
REF
1
1-1
2
3
4
4-1
5
6-1
6-2
7
PART�#
X1677001
X1677001-1 LOWER�PANEL
X1677002
XPHTEK6
X1677004
X1677004-1 HINGE�PIN
X1677005
XPS24
DESCRIPTION
CABINET
REF
87-1
87-2
87-3
87-4
87-6
87-7
87-8
87-9
88
88-1
88-2
88-3
90
90
91
104
154
155
211
212
213
218
219
225
PART�#
XPS31
XPN07
X1677087-3 MOTOR�CORD
X1677087-4 POWER�CORD
X1677087-6 STRAIN�RELIEF
X1677087-7 WIRE�CONNECTORS
X1677087-8 SWITCH�COVER
X1677087-9 PLASTIC�SWITCH�SCREW
X1677088
XPFH25
XPW07
XPN02
X1677090
X1711090
W1010
DESCRIPTION
PHLP�HD�SCR�10-24�X�1-3/4
HEX�NUT�10-24
SCALE
TAP�SCREW�#10�X�3/8
MOTOR�COVER
CORD�CLAMP
PHLP�HD�SCR�8-32�X�3/8
HEX�NUT�8-32
LATCH�2�PCS
SNAP�IN�STRAIN�RELIEF
XPN14
X1677007
X1677058
SWITCH�PLATE
FLAT�HD�SCR�5/16-18�X�1
FLAT�WASHER�5/16
HEX�NUT�5/16-18
W1677�WARNING�ID�LABEL
W1711�WARNING�ID�LABEL
DUST�HOSE�ADAPTER
FLAT�WASHER�#10
58
58-1
58-2
79
80
80-1
81
82
83
84
84-1
85
X1677058-1 CORD�CLAMP�PLATE�2�HOLE
X1677058-2 CORD�CLAMP�PLATE�1�HOLE
XPSS07
X1677080
X1677080-1 DADO�TABLE�INSERT
X1677081
XPLW04
XPB24
SET�SCREW�1/4-20�X�1/2
STANDARD�TABLE�INSERT
XPW03
TABLE
X1677154
X1677155
D3377
XLABEL-02
XLABEL-01
XLABEL-04
XLABEL-08
X1677225
SWITCH�PLATE�BRACE
MOTOR�BRACE
LOCK�WASHER�3/8
HEX�BOLT�3/8-16�X�1-1/4
EXTENSION�WING�(LEFT)
SHOP�FOX�LOGO�PLATE
DISCONNECT�POWER�LABEL
SAFETY�GLASSES�LABEL
ELECTRICITY�LABEL
READ�MANUAL�LABEL
BLACK�STRIPE
X1677084
X1677084-1 EXTENSION�WING�(RIGHT)
XPW02
XPSB16
X1677087
X1711087
FLAT�WASHER�3/8
86
87
87
CAP�SCREW�3/8-16�X�3/4
MAGNETIC�SWITCH�W1677
MAGNETIC�SWITCH�W1711
-51-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Motor/Trunnion Breakdown
���
-52-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
REF
8
9
10
11
12
13
14
15
PART�#
X1677008
X1677009
X1677010
XPSS15
XPSB65
X1677013
XPS27
X1677015
X1677016
X1677016-1 GUIDE�BLOCK
XPSB05
XPW06
X1677017
XPS35
DESCRIPTION
HANDWHEEL�LOCK
HANDLE
HANDWHEEL
SET�SCREW�3/8-16�X�3/8
CAP�SCREW�10-24�X�2
POINTER�BRACKET
PHLP�HD�SCR�5/16-18�X�3/8
POINTER
REF
45
47
48
50
51
52
53
54
PART�#
X1677045
X1677047
X1677048
X1677050
X1677051
X1677052
XPB14
X1677054
X1677055
X1677056
X1711056
DESCRIPTION
BLADE�ARBOR
ARBOR�FLANGE
ARBOR�NUT�5/8�RH
MOTOR�FRAME�SUPPORT
HAIR�PIN�COTTER�PIN
PIVOT�PIN
CAP�SCREW�3/8-16�X�1
V-BELTS,�SET�OF�3,�FM-25�
MOTOR�PULLEY
16
FRONT�TRUNNION�BRACKET
55
56
56
16-1
16-2
16-3
17
18
19
20
21
22
23
24
25
26
26-1
27
27-1
28
29-1
29-2
30
30-1
30-2
31
32
33
35
35-3
35-4
36
37-1
37-2
38
40
41
42
43
43-1
44
W1677�MOTOR�3HP
W1711�MOTOR�5HP�
CAP�SCREW�1/4-20�X�3/4
FLAT�WASHER�1/4
SHIELD�PLATE
PHLP�HD�SCR�5/16-18�X�3/4
CAP�SCREW�3/8-16�X�1-1/2
LOCK�WASHER�3/8
HEX�NUT�3/8-16
SET�SCREW�1/4-20�X�3/8
WORM�GEAR
COLLAR
SET�SCREW�5/16-18�X�1/4
TILT�SHAFT
BRASS�WASHER�3/4
PIN
56-1
56-1
56-2
56-2
56-3
56-3
56-4
56-5
56-5
56-6
56-6
56-7
56-7
61
63-1
63-2
64
65
66
68
69
70
85
89
92
94
95
95-1
95-2
99
216
217
220
221
233
X1677056-1 W1677�MOTOR�FAN�COVER
X1711056-1 W1711�MOTOR�FAN�COVER
X1677056-2 W1677�MOTOR�FAN
X1711056-2 W1711�MOTOR�FAN
X1677056-3 W1677�CAPACITOR�COVER
X1711056-3 W1711�CAPACITOR�COVER
XPC050-1
XPC600
XPC400-1
X1677056-6 W1677�WIRING�BOX
X1711056-6 W1711�WIRING�BOX
X1677056-7 W1677�MOTOR�PLATE
X1711056-7 W1711�MOTOR�PLATE
XPSB26
XPLW04
XPN08
XPSS03
W1711�R�CAP�50M,�350V
W1677�S�CAP�600M,�125V
W1711�S�CAP�400M,125V
X1677023
X1677024
XPSS05
X1677026
XPBW02
X1677027
X1677027-1 BEARING�LOAD�SPRING
XPK02M KEY�5�X�5�X�40
X1677029-1 GEARED�TRUNNION
X1677029-2 BUSHING
XPN02
XPSB08
X1677030-2 SPACER
XPW07
FLAT�WASHER�5/16
X1677063-1 REAR�TRUNNION
X1677063-2 BUSHING
XPRP07
XPSB14
ROLL�PIN�5/16�X�1
CAP�SCREW�3/8-16�X�1
LOCK�WASHER�3/8
SHAFT
HEX�NUT�5/16-18
CAP�SCREW�5/16-18�X�1-1/2
XPLW04
X1677068
XPLN05
X1677070
XPW02
XPK02M
XPLW01
X1677094
X1677095
XPSS08
XPB03
HEX�BOLT�5/16-18�X�1
FLANGE
SHAFT
LOCK�NUT�3/4-16
X1677032
X1677033
X1677035
X1677035-3 HOUSING�CAP
XPS06
XPSB26
XPLW04
XPK18
REAR�TRUNNION�BRACKET
FLAT�WASHER�3/8
KEY�5�X�5�X�40
LOCK�WASHER�5/16
DUST�DEFLECTOR
SPECIAL�SCR�5/16-18�X�1-1/4
SET�SCREW�5/16-18�X�1/2
HEX�NUT�5/16-18
HEX�BOLT�5/16-18�X�5/8
COMBO�WRENCH�7/8
ARBOR�WRENCH
GEARED�BEARING�HOUSING
PHLP�HD�SCR�10-24�X�3/8
CAP�SCREW�3/8-16�X�1-1/2
LOCK�WASHER�3/8
KEY�1/4�X�1/4�X�1-3/4
XPN02
XPB32
XP6203-2RS BEARING�6203�2RS
X1677040
X1677041
X1677042
XPSS10
XPSS06
XPK02M
ARBOR�NUT�5/8-18�LH
COLLAR
ARBOR�PULLEY
SET�SCREW�1/4-20�X�5/8
SET�SCREW�1/4-20�X�3/4
KEY�5�X�5�X�40
XPWR78
X1677217
XPAW03
XPAW04
XPAW08
HEX�WRENCH�3MM
HEX�WRENCH�4MM
HEX�WRENCH�8MM
-53-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Guard/Miter Gauge Breakdown
-54-
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
REF
57
57-1
60
61
62
72
73
74
140
141
142
143
144
145
200
PART�#
XPB15
XPW07
XPB07
XPW07
X1677062
X1677072
X1677073
X1677074
XPB11
XPW07
XPLW01
XPN02
DESCRIPTION
REF
201
PART�#
X1677201
DESCRIPTION
MITER�GAUGE�BODY
HEX�BOLT�5/16-18�X�3/8
FLAT�WASHER�5/16
HEX�BOLT�5/16-18�X�3/4
FLAT�WASHER�5/16
BRACKET
201-1 X1677201-1 RIVET�2�X�4
201-2 X1677201-2 MITER�GAUGE�SCALE
202
203
204
205
206
207
208
209
210
300
301
X1677202
X1677203
XPW07
X1677205
XPFH04
X1677207
X1677208
X1677209
XPSS31
X1677300
X1677301
MITER�GAUGE�HANDLE
STAR�KNOB�5/16-18�X�1-1/4
FLAT�WASHER�5/16
POINTER
FLAT�HD�SCR�1/4-20�X�5/8
MITER�SLIDE�BAR
SPECIAL�SCREW
SPECIAL�WASHER
SET�SCREW�10-24�X�5/8
BLADE�GUARD�ASSEMBLY
BLADE�GUARD�LABEL
SHAFT
UPR�BLADE�GUARD�BRACKET
LWR�BLADE�GUARD�BRACKET
HEX�BOLT�5/16-18�X�1-1/2
FLAT�WASHER�5/16
LOCK�WASHER�5/16
HEX�NUT�5/16-18
HEX�BOLT�5/16-18�X�1
SET�SCREW�5/16-18�X�3/8
COMPLETE�MITER�GAUGE
XPB03
XPSS02
X1677200
Safety labels warn about machine hazards and how to prevent machine damage or injury. The
owner of this machine MUST maintain the original location and readability of all labels on this
machine. If any label is removed or becomes unreadable, REPLACE that label before allowing the
machine to enter service again. Contact Woodstock International, Inc. at (360) 734-3482 or www.
shopfoxtools.com to order new labels.
-55-
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Woodstock International, Inc. warrants all SHOP FOX® machinery to be free of defects from work-
manship and materials for a period of two years from the date of original purchase by the original
owner. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence
or accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the SHOP FOX®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the SHOP FOX® factory service center or authorized repair
facility designated by our Bellingham, WA office, with proof of their purchase of the product within
two years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect resulted from
causes not within the scope of Woodstock International Inc.'s warranty, then the original owner must
bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited
to the duration of this written warranty. We do not warrant that SHOP FOX® machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all SHOP FOX® machinery meets high quality and durabil-
ity standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
W1677/W1711 10" Table Saw
Warranty Registration
Name___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________State___________________________Zip________________________
Phone #______________________Email __________________________Invoice #___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement
____ Friend
____ Website
____ Local Store
____ Other:
_____ Mail Order Catalog
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years _____ 2-8 Years ____8-20 Years
_____ 20+ Years
3. How many of your machines or tools are Shop Fox®?
_____ 0-2 _____ 3-5 ____6-9
_____ 10+
____ No
____ No
4. Do you think your machine represents a good value?
_____ Yes
5. Would you recommend Shop Fox® products to a friend? _____ Yes
6. What is your age group?
_____ 20-29
_____ 50-59
____ 30-39
____ 60-69
____ 40-49
____ 70+
7. What is your annual household income?
_____ $20,000-$29,000
_____ $50,000-$59,000
____ $30,000-$39,000
____ $60,000-$69,000
____ $40,000-$49,000
____ $70,000+
8. Which of the following magazines do you subscribe to?
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
____ Rifle
____ Shop Notes
____ Shotgun News
9. Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|