Model D2254-6, D2303
Wood Vises
Instruction Sheet
Introduction
Your new Wood Vise (Figure 1) is designed to fit on work-
benches 21⁄4" and thicker, but can be adapted to work-
1
benches down to 1 ⁄2" thick by using a shim. Holes are
pre-drilled in the jaw faces to attach aftermarket or shop-
built wood clamping vise jaw pads.
Specifications
Model
D2254
6"
D2255
8"
D2256
D2303
10"
Model D2254 Shown
Jaw Width
61⁄2
"
Figure 1. Shop Fox wood vise.
Workbench
Thickness
21⁄4
"
21⁄4
"
21⁄4
"
21⁄4
"
Maximum
Jaw Opening
55⁄8
"
71⁄4
"
73⁄8
"
83⁄8
"
���������
����
Weight
7 lbs.
11 lbs.
8 lbs.
14 lbs.
����
Installation
1. Have another person hold the vise up against the
Figure 2. Shim placed between workbench
workbench in the desired mounting location.
and vise for workbenches under 21⁄4".
Model D2256 Only: If the workbench has holes for
bench dogs, make sure the bench dog on the vise is
aligned with those holes.
Mounting Holes for
Wood Screws
Note: If the workbench is less than 21⁄4" thick, use a
piece of scrap wood (Figure 2) between the vise and
workbench as a shim. Cut the shim to the necessary
thickness so the vise does not protrude above the
workbench after mounting.
2. Use a pencil to mark the workbench through the four
vise mounting holes (Figure 3) so you know where to
drill pilot holes in the workbench.
Figure 3. Mounting hole locations.
3. Use a 1⁄8" drill bit to drill pilot holes approximately
11⁄2" deep in the underside of the workbench.
COPYRIGHT © FEBRUARY, 2008 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#10497TR
Printed in China
Download from Www.Somanuals.com. All Manuals Search And Download.
D2254-6, D2303 Wood Vise Instructions
D2254 Parts
�
�
�
�
REF PART�#
DESCRIPTION
1
2
3
4
5
6
XD2254001 FIXED�JAW
XD2254002 MOVABLE�JAW
XD2254003 GUIDE�SHAFT
�
�
XD2254004 LEADSCREW�HANDLE
XPW14M
FLAT�WASHER�15MM
XD2256006 COTTER�PIN�3�X�20
D2255 Parts
�
�
�
�
REF PART�#
DESCRIPTION
1
2
3
4
5
6
XD2255001 FIXED�JAW
XD2255002 MOVABLE�JAW
XD2255003 GUIDE�SHAFT
�
�
XD2255004 LEADSCREW�HANDLE
XPW18M
FLAT�WASHER�18MM
XD2255006 COTTER�PIN�3�X�25
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
D2254-6, D2303 Wood Vise Instructions
D2256 Parts
�
�
�
�
REF PART�#
DESCRIPTION
�
1
2
3
4
5
6
7
8
XD2256001 FIXED�JAW
XD2256002 MOVABLE�JAW
XD2256003 GUIDE�SHAFT
XD2256004 LEADSCREW�HANDLE
XPW08M
XD2256006 COTTER�PIN�3�X�20
XD2256007 DOG
XD2256008 FINGER�SCREW
�
�
�
FLAT�WASHER�16MM
D2303 Parts
�
�
�
�
REF PART�#
DESCRIPTION
1
2
3
4
5
6
XD2303001 FIXED�JAW
XD2303002 MOVABLE�JAW
XD2303003 GUIDE�SHAFT
�
�
XD2303004 LEADSCREW�HANDLE
XPW18M
FLAT�WASHER�18MM
XD2303006 COTTER�PIN�4�X�30
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
|