Woods Equipment Lawn Mower Accessory MAN0115 User Manual

MOW’N MACHINE  
15 cu. ft. Metal Grasscatcher  
For F-Series  
Power Units  
Tested. Proven. Unbeatable.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOPPER ASSEMBLY  
Assembly of hopper will be easier if assembled upside  
down on a flat surface, see Figure 2. Note that Figure 1  
shows hopper in the upright position.  
ASSEMBLE HOPPER  
!
LEA EL INSTRUCTIVO!  
NOTE: When assembling the hopper, make sure bolts  
that will interfere with grass clippings are installed with  
heads on the inside. This will prevent clippings from  
catching on bolts when the grasscatcher is dumped.  
Si no lee Ingles, pida ayuda a  
alguien que si lo lea para que le  
traduzca las medidas de seguridad.  
Leave hardware loose until hopper is assembled.  
1. Lay top section upside down on a flat surface,  
using Figure 1 as a guide for assembly.  
Only use grass collection system with dual tail-  
wheel option.  
NOTE: Do not install bolts in side holes where  
upper and lower crossmembers will mount (refer to  
Figure 4, items 12 & 15).  
2. Attach side panels (6, 7), upper front panel (8) and  
back panel (9) to hopper top (1). Make sure side  
panel corners are outside the front and back  
panels as shown in Figure 2.  
3. Fasten bottom panel (11) to the side panels and to  
the outside of the front panel (Figure 1).  
6
8
9
7
1
DP1  
Figure 2. Assemble Hopper Upside Down  
1. 70521 Hop-  
per top  
4. 70067 1/4 NC x 1/2 Whiz bolt  
5. 70065 1/4 NC Whiz nut  
6.1000664 Right side panel  
7.1000665 Left side panel  
8. 70528 Upper front panel  
9. 70530 Back panel  
11. 1000667 Bottom panel  
Figure 1. Hopper Assembly  
Assembly 3  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. Make sure two pivot bearings (13), (Figure 4) are  
attached to the inside of front cross channel (15)  
using sheet metal screws (14). Do not tighten at  
this time.  
INSTALL CROSSMEMBERS  
3. Slide left side door trip lever (17) through opening  
on left side panel, pivot bearings (13) attached to  
front cross channel (15), and right side panel.  
Front Crossmember  
4. Secure front cross channel (15) to bottom panel  
using whiz bolts (4) and whiz nuts (5). Tighten  
sheet metal screws.  
5. Attach right dump lever (18) to door trip lever (17),  
so that both bars face forward. Secure using cap  
screw (19) and lock nut (20).  
6. Mount rear cross channel (12) on outside of bottom  
panel using whiz bolts (4) and whiz nuts (5) as  
shown. Make sure pivot hinge is at the bottom.  
DP7A  
7. Attach left and right door hinge mounts (26, 27) to  
back and side panels as shown in Figure 5. Use  
whiz bolt (10) and whiz nut (5) to secure hinge  
mount to back panel.  
Figure 3. Side Panel & Front Crossmember Installed  
10  
5
4
5
26  
4. 70067 1/4 NC x 1/2 Whiz bolt  
5. 70065 1/4 NC Whiz nut  
12.1000679 Rear cross channel  
13. 71163 Pivot bearing  
14. 27610 5/16 x 3/4 Sheet metal screw  
15.1000680 Front cross channel  
17.1000677 Left side door trip lever  
18.1000678 Right dump lever  
4. 70067 1/4 NC x 1/2 Whiz bolt  
5. 70065 1/4 NC Whiz nut  
10. 70068 1/4 NC x 3/4 Whiz bolt  
26. 70536 Right door hinge  
19.  
20.  
3184 1/4 NC x 1-1/4 HHCS  
6128 1/4 NC Lock nut  
Figure 5. Right Door Hinge Mount Installation  
26. 70536 Right door hinge  
27. 70537 Left door hinge  
INSTALL DOOR  
NOTE: 90° bend on latch bracket faces forward.  
1. Attach latch brackets (28) to bottom of door (24).  
2. Place nylon bearings (23) into door hinge mounts.  
Figure 4. Crossmember Installation  
NOTE: Hopper should still be upside down. Do not  
tighten hardware.  
3. Insert both left and right door hinges (26, 27) into  
door hinge mounts.  
1. Install front crossmember (16) between right and  
left side panels. Install crossmember with brackets  
facing forward as shown in Figure 3.  
4. Place door (24) over hinges and secure with whiz  
bolt (4, 10) and whiz nut (5).  
(Rev. 8/17/2007)  
4 Assembly  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Torque all hardware according to page 8.  
2. Attach latch linkage rod (36) to both right and left  
door handle mount. Be sure to install spring  
bracket (35) into clevis when attaching left side  
(see Figure 7).  
3. Attach opposite end of door linkage rod (45) to  
door handle mount.  
4. Adjust linkage so that there is a slight amount of  
pressure holding the door closed when handle is  
snapped over center.  
5. Attach opposite end of latch linkage rod to door  
latches.  
6. Attach spring (34) to hole in side panel with spring  
anchor (35) on left side and to spring bracket (33)  
as shown in Figure 7.  
7. Adjust latch linkage rods so that the door latches  
will release just before the door opens when the  
door handle is moved forward.  
4. 70067 1/4 NC x 1/2  
Whiz bolt  
5. 70065 1/4 NC Whiz nut  
10. 70068 1/4 NC x 3/4 Whiz bolt  
23. 70026 Nylon bearing  
24. 70531 Door  
48  
39  
40  
29  
31  
32  
26. 70536 Right door hinge  
27. 70537 Left door hinge  
45  
39  
40  
40  
36  
Figure 6. Door Assembly  
INSTALL DOOR HANDLE  
NOTE: Turn hopper assembly over and support in  
upright position.  
33  
34  
35  
29. 70526 Hopper handle  
31. 1686 3/8 NC x 3/4 HHCS  
1. Attach door handle (29) to left door handle mount  
as shown in Figure 7.  
2. Install stop lever (49) and rubber bumper (50) to  
right side panel as shown in Figure 8.  
32. 15030 3/8 NC Flange lock nut  
33. 70546 Link  
3. Install latch pivot bracket (42) to both sides of  
grasscatcher as shown in Figure 8.  
34. 70834 Spring  
35.1001501 Spring anchor bracket  
36. 70547 Linkage latch rod  
4. Attach door latches (44) to latch pivot brackets.  
Adjust latch brackets (28) so that the door latches  
will hold the door tightly shut (see Figure 8).  
39. 70024 Clevis pin, 5/16 x 25/32  
40. 1326 Cotter pin, 1/8 x 1/2  
INSTALL LINKAGE  
45. 70548 Linkage door rod  
1. Attach door linkage rod (36) to both right and left  
door hinge as shown in Figure 7 and Figure 8.  
Place head of clevis pin to the outside.  
48. 64151 Clevis pin, 3/8 x 1-1/8  
Figure 7. Left Side  
Assembly 5  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Install rubber bumpers (19). Secure with flange  
lock nuts (13).  
48  
40  
5
1
9
45  
36  
8
49  
50  
7
19  
13  
28  
2
42  
5
41  
39 40  
40  
44  
4
6
7
4. 70067 1/4 NC x 1/2 Whiz bolt  
5. 70065 1/4 NC Whiz nut  
28. 70538 Latch bracket  
36. 70547 Linkage latch rod  
39. 70024 Clevis pin  
1. 74082 Right hopper support  
2. 74083 Left hopper support  
5. 74084 Cross brace  
40.  
41.  
1326 Cotter pin, 1/8 x 1/2  
4378 5/16 Flat washer  
6.  
920 3/8 NC x 1-3/4 Cap screw GR5  
42. 70543 Latch pivot bracket  
44. 70545 Left side door latch  
45. 70548 Linkage door rod  
48. 64151 Clevis pin  
7. 15030 3/8 NC Flanged lock nut  
8. 62153 3/8 NC Flanged screw  
9.  
565 Flat Washer  
13. 14139 5/16 NC Flange lock nut  
19. 71444 Rubber bumper  
49.1000670 Lever stop  
50. 71444 Rubber bumper  
Figure 8. Right Side  
Figure 9. Hopper Mounting (Left Side Shown)  
INSTALL HOPPER SUPPORTS  
1. Remove two center 3/8 NC x 3/4 hex washer head  
cap screws from both right and left side of hood  
assembly. Note: Drill completely through hood  
frame if not already done.  
2. Attach left hopper support (2) to hood assembly.  
Secure using two cap screws (6) and flange screw  
(7) as shown in Figure 9.  
3. Repeat steps 1 & 2 to install right support (1).  
4. Install cross brace (5) between hopper supports.  
Secure with cap screws (8), washer (9), and lock  
nut (7). See Figure 10.  
Figure 10. Mounting Bracket Instructions  
(Rev. 8/17/2007)  
6 Assembly  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Align hinges of rear crossmember (12) on hopper with  
hinges of rear hopper pivot (4). Insert clevis pins (14)  
and hair pins (15) as shown in Figure 12.  
INSTALL REAR HOPPER SUPPORT &  
REAR HOPPER PIVOT  
1. Attach rear hopper support (3) to the rear of the  
power unit using four flanged head cap screws (8),  
standard flat washers (9), and two flange lock nuts  
(7) as shown in Figure 11.  
ATTACH CABLE  
1. Attach cable (10) to rear of power unit on both right  
and left sides as shown in Figure 13.  
NOTE: Remove cap screw for ground cable on  
21D & 25L power units.  
2. Attach the rear hopper pivot (4) to the rear hopper  
support using four flanged head cap screws (8),  
washers (9), and flange lock nuts (7).  
2. Secure with flanged cap screw (8), washer (9), and  
flange lock nut (7). Leave hardware loose at this  
time.  
3. Remove the fourth whiz bolt and whiz nut from the  
bottom of both right and left side panels.  
7
8
9
4. Install whiz bolt (16), other end of cable (10), flat  
washer (9), and whiz nut previously removed in this  
hole position as shown in Figure 13.  
4
5. Pivot hopper back and allow weight of hopper on  
8
7
cables. Torque hardware at this time.  
3
16  
9
8
7
9
DP4  
10  
3. 74082 Rear hopper support  
4. 73678 Rear hopper pivot  
7. 15030 3/8 NC Flange lock nut  
8. 62153 3/8 NC x 1 Flanged cap screw  
9. 565 3/8 Standard flat washer  
Figure 11. Rear Hopper Support & Rear Hopper Pivot  
7
9
8
7. 15030 3/8 NC Flange lock nut (2)  
8. 62153 3/8 NC Flanged cap screw (2)  
MOUNT HOPPER ASSEMBLY  
9.  
565 3/8 Flat washer (4)  
12  
10. 73957 Cable  
16. 70068 1/4 NC x 3/4 Whiz bolt (2)  
Figure 13. Cable Installed (Right Side Shown)  
4
14  
15  
4. 73678 Rear hopper pivot  
12. 1000679 Rear cross channel (Hopper)  
14. 63523 3/4 x 4-1/2 Clevis pin (2)  
15.  
2688 5/32 Hair pin cotter (2)  
Figure 12. Hinge Pin Installed (Left Hinge Shown)  
(Rev. 8/17/2007)  
Assembly 7  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Tilt hopper assembly back.  
SECURE HOPPER  
1. Rotate hopper onto right and left hopper supports.  
NOTICE  
2. Insert 3/8 lynch pins (18) to attach front hopper  
crossmember to support brace as shown in Figure  
14.  
Do not attempt to tilt hopper to service position  
unless hopper is completely empty. Failure to  
empty hopper could result in damage to hopper.  
4. On power unit, unhook rubber latches and lift hood  
assembly to service position.  
5. Secure with prop rod.  
18  
18. 33000 3/8 x 2-1/4 Lynch pins  
Figure 14. Latch Locked into Position  
POSITION HOOD FOR SERVICING ENGINE  
DP5  
To flip hood up for servicing engine, follow these steps:  
1. Disconnect vacuum hose from hose adapter chute  
Figure 15. Servicing Engine  
on vacuum.  
2. Remove lynch pins from hopper support (Figure  
14).  
TORQUE SPECIFICATIONS  
Wrench  
Size  
Hardware  
Location  
Ref  
4
Cap Screw  
1/4 NC x 1/2 Whiz bolt  
3/8 NC x 1-3/4 HHCS  
3/8 NC x 1 FHCS  
Qty  
68  
4
Required Torque  
10 lbs-ft (13 N-m)  
35 lbs-ft (47 N-m)  
35 lbs-ft (47 N-m)  
10 lbs-ft (13 N-m)  
19 lbs-ft (26 N-m)  
10 lbs-ft (13 N-m)  
35 lbs-ft (47 N-m)  
7/16  
9/16  
9/16  
7/16  
1/2  
Hopper Assembly  
Mount Assembly  
Mount Assembly  
Hopper Assembly  
Hopper Assembly  
Hopper Assembly  
Hopper Assembly  
6
8
12  
14  
4
10 1/4 NC x 3/4 Whiz bolt  
14 5/16 x 3/4 Sheet metal screw  
19 1/4 NC x 1-1/4 HHCS  
31 3/8 NC x 3/4 HHCS  
1
7/16  
9/16  
2
8 Assembly  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MOUNT ASSEMBLY  
REF PARTS QTY  
DESCRIPTION  
Right hopper support  
REF PARTS QTY  
DESCRIPTION  
1
2
74082  
74083  
73677  
73678  
74084  
920  
1
1
1
1
1
4
11  
12  
13  
14  
15  
16  
17  
18  
19  
4528  
6778  
4
4
2
2
2
2
2
2
2
5/16 NC x 1-3/4 Cap screw GR5  
5/16 NC Lock nut  
Left hopper support  
3
Rear hopper support  
Rear hopper pivot  
14139  
63523  
2688  
5/16 NC Flange lock nut  
3/4 x 4-1/2 Clevis pin  
5/32 Hair pin cotter  
1/4 x 3/4 Whiz bolt  
1/4 Whiz nut  
4
5
Hopper cross brace  
6
3/8 NC x 1-3/4 Cap screw GR5  
70068  
70065  
33000  
71444  
7
15030 12 3/8 NC Flange lock nut  
8
62153 12 3/8 NC x 1 Flanged head cap screw  
3/8 x 2-1/4 Lynch pin  
Rubber bumper  
9
565  
8
2
3/8 Standard flat washer  
Cable assembly  
10  
73957  
Parts 9  
MAN0115 (Rev.3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOPPER ASSEMBLY  
10 Parts  
MAN0115 (Rev. 3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HOPPER ASSEMBLY PART LIST  
REF PARTS QTY  
DESCRIPTION  
Hopper top  
REF PARTS QTY  
DESCRIPTION  
Latch bracket  
1
70521  
70504  
70505  
1
1
2
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
70538  
70526  
70527  
1686  
2
1
1
2
2
1
1
1
2
2
2
2
8
9
1
1
1
2
2
2
2
1
1
1
1
1
2
Window  
Hopper handle  
3
Mounting bracket  
Handle grip, .812 x 4  
3/8 NC x 3/4 HHCS  
3/8 NC Flange lock nut  
Link, .19 x .75 x 4.0  
Spring  
4
70067 68 1/4 NC x 1/2 Whiz bolt  
70065 82 1/4 NC Whiz nut  
5
15030  
70546  
70834  
1001501  
70547  
5283  
6
1000664  
1000665  
70528  
1
1
1
1
Right side panel  
Left side panel  
Upper front panel  
Back panel  
7
8
Spring anchor bracket  
Linkage latch rod  
5/16 NF Hex nut  
9
70530  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
70068 14 1/4 NC x 3/4 Whiz bolt  
1000667  
1000679  
71163  
1
1
2
4
1
1
1
1
1
1
1
1
2
1
1
2
2
Bottom panel  
70022  
70024  
1326  
Adjustable clevis, 5/16 NF  
Clevis pin, 5/16 x 25/32  
Cotter pin, 1/8 x 1/2  
5/16 Flat washer  
Rear cross channel  
Pivot bearing  
27610  
1000680  
74085  
1000677  
1000678  
3184  
5/16 x 3/4 Sheet metal screw  
Front cross channel  
Front crossmember  
Left door trip lever  
Right dump lever  
1/4 NC x 1-1/4 HHCS  
1/4 NC Lock nut  
4378  
70543  
70544  
70545  
70548  
1271  
Latch pivot bracket  
Right side door latch  
Left side door latch  
Linkage door rod  
3/8 NF Hex nut  
6128  
70360  
64151  
1000670  
71444  
14139  
1001018  
70523  
Adjustable clevis, 3/8NF  
Clevis pin, 3/8 x 1-1/8  
Lever stop  
70534  
70535  
70026  
70531  
70552  
70536  
70537  
Right door hinge mount  
Left door hinge mount  
Nylon bearing (included. w/ 21 & 22)  
Door  
Rubber bumper  
5/16 NC Flange lock nut  
64" Flex hose  
Door seal  
Right door hinge  
6" Hose clamp  
Left door hinge  
Parts 11  
MAN0115 (Rev.3/31/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOLT TORQUE CHART  
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific  
application.  
Fasteners must always be replaced with the same grade as specified in the manual parts list.  
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.  
Make sure fastener threads are clean and you start thread engagement properly.  
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.  
SAE Bolt Head  
Identification  
SAE SERIES  
TORQUE  
CHART  
A
SAE Grade 2  
(No Dashes)  
SAE Grade 8  
(6 Radial Dashes)  
SAE Grade 5  
(3 Radial Dashes)  
MARKING ON HEAD  
A
SAE 2  
SAE 5  
SAE 8  
Diameter  
(Inches)  
Wrench  
Size  
lbs-ft  
N-m  
8
lbs-ft  
10  
N-m  
13  
lbs-ft  
14  
N-m  
1/4"  
5/16"  
3/8"  
7/16"  
1/2"  
9/16"  
5/8"  
3/4"  
7/8"  
1"  
7/16"  
1/2"  
6
18  
37  
12  
17  
19  
26  
27  
9/16"  
5/8"  
23  
31  
35  
47  
49  
67  
36  
48  
55  
75  
78  
106  
163  
232  
325  
569  
907  
1383  
3/4"  
55  
75  
85  
115  
164  
230  
403  
642  
979  
120  
171  
240  
420  
669  
1020  
13/16"  
15/16"  
1-1/8"  
1-5/16"  
1-1/2"  
78  
106  
149  
261  
416  
634  
121  
170  
297  
474  
722  
110  
192  
306  
467  
METRIC SERIES  
TORQUE  
CHART  
8.8  
Metric Bolt Head  
Identification  
10.9  
A
Metric  
Grade 8.8  
Metric  
Grade 10.9  
COARSE THREAD  
FINE THREAD  
A
A
MARKING ON HEAD  
MARKING ON HEAD  
Diameter &  
Thread Pitch Wrench  
(Millimeters)  
Diameter &  
Thread Pitch  
(Millimeters)  
Metric 8.8  
Metric 10.9  
N-m lbs-ft  
Metric 8.8  
Metric 10.9  
N-m lbs-ft  
Size  
N-m  
lbs-ft  
6
N-m  
lbs-ft  
6
6 x 1.0  
10 mm  
13 mm  
16 mm  
18 mm  
21 mm  
24 mm  
27 mm  
30 mm  
34 mm  
36 mm  
46 mm  
8
11  
27  
8
8
11  
29  
8
6 x 1.0  
8 x 1.0  
8 x 1.25  
10 x 1.5  
12 x 1.75  
14 x 2.0  
16 x 2.0  
18 x 2.5  
20 x 2.5  
22 x 2.5  
24 x 3.0  
30 x 3.0  
20  
15  
20  
21  
16  
22  
39  
29  
54  
40  
41  
30  
57  
42  
10 x 1.25  
12 x 1.25  
14 x 1.5  
16 x 1.5  
18 x 1.5  
20 x 1.5  
22 x 1.5  
24 x 2.0  
30 x 2.0  
68  
50  
94  
70  
75  
55  
103  
163  
250  
363  
507  
684  
861  
1740  
76  
109  
169  
234  
330  
451  
571  
1175  
80  
151  
234  
323  
457  
623  
790  
1626  
111  
173  
239  
337  
460  
583  
1199  
118  
181  
263  
367  
495  
623  
1258  
87  
120  
184  
268  
374  
505  
635  
1283  
125  
172  
244  
332  
421  
867  
133  
194  
270  
365  
459  
928  
Typical Washer  
Installations  
Bolt  
Flat Washer  
Lock Washer  
8/9/00  
Bolt Torque & Size Charts (Rev. 10/10/2005)  
12 Appendix  
Download from Www.Somanuals.com. All Manuals Search And Download.  
BOLT SIZE CHART  
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.  
SAE Bolt Thread Sizes  
5/16  
3/8  
1/2  
5/8  
3/4  
7/8  
IN  
1
2
7
3
4
5
6
MM  
25  
50  
75  
100  
125  
150  
175  
Metric Bolt Thread Sizes  
8MM 10MM  
12MM  
14MM  
16MM  
18MM  
ABBREVIATIONS  
AG.............................................................Agriculture  
ATF...............................Automatic Transmission Fluid  
BSPP .......................... British Standard Pipe Parallel  
BSPTM...............British Standard Pipe Tapered Male  
CV.................................................. Constant Velocity  
CCW ............................................ Counter-Clockwise  
CW............................................................. Clockwise  
F..................................................................... Female  
GA................................................................... Gauge  
GR (5, etc.) .........................................Grade (5, etc.)  
HHCS.......................................Hex Head Cap Screw  
HT ......................................................... Heat-Treated  
JIC............... Joint Industry Council 37° Degree Flare  
LH ...............................................................Left Hand  
LT ......................................................................... Left  
m.......................................................................Meter  
mm ..............................................................Millimeter  
M........................................................................ Male  
MPa........................................................Mega Pascal  
N ....................................................................Newton  
NC ....................................................National Coarse  
NF......................................................... National Fine  
NPSM ...................National Pipe Straight Mechanical  
NPT ........................................ National Pipe Tapered  
NPT SWF .......National Pipe Tapered Swivel Female  
ORBM......................................... O-Ring Boss - Male  
P .........................................................................Pitch  
PBY .................................................... Power-Beyond  
psi........................................Pounds per Square Inch  
PTO ................................................... Power Take Off  
QD ..................................................Quick Disconnect  
RH ............................................................Right Hand  
ROPS..........................Roll-Over Protective Structure  
RPM.......................................Revolutions Per Minute  
RT...................................................................... Right  
SAE ........................Society of Automotive Engineers  
UNC....................................................Unified Coarse  
UNF ........................................................ Unified Fine  
UNS....................................................Unified Special  
Bolt Torque & Size Charts (Rev. 10/10/2005)  
Appendix 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
TM  
(Mow’n Machine Zero-Turn Mower and  
TM  
Woods Boundary Utility Vehicle Replacement Parts)  
TM  
Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine zero-turn  
TM  
mowers and attachments and Woods Boundary utility vehicles, accessories and attachments to be free  
from defect in material and workmanship for a period of ninety (90) days from the date of delivery of the  
product to the original purchaser.  
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED IN DURATION TO A PERIOD OF NINETY (90) DAYS FROM THE  
DATE OF DELIVERY OF THE PRODUCT TO THE ORIGINAL PURCHASER. Some states do not  
allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser  
sell or otherwise transfer the product to a third party, this Warranty does not transfer to the third party  
purchaser in any way. There are no third party beneficiaries of this Warranty.  
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure  
or loss caused by improper operation, improper maintenance, misuse, or an accident.  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement,  
free of charge, of the product if the product is defective or in noncompliance with this Warranty. The  
product must be returned to WOODS with proof of purchase within thirty (30) days after such  
defect or noncompliance is discovered or should have been discovered, routed through the dealer  
and distributor from whom the purchase was made, transportation charges prepaid. WOODS  
shall complete such repair or replacement within a reasonable time after WOODS receives the product.  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses,  
arising directly or indirectly from the product, whether such claim is based upon breach of  
contract, breach of warranty, negligence, strict liability in tort or any other legal theory. Without  
limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business,  
revenues or goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental;  
or (iii) any other type of damage to property or economic loss. Some states do not allow the exclusion or  
limitation of incidental or consequential damages, so the above limitations may not apply to you.  
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,  
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is  
authorized to alter, modify, or enlarge this Warranty.  
This Warranty gives you specific legal rights, and you may also have other rights which may vary from  
state to state.  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
(Mow’n Machine Zero-Turn Mowers and Woods Boundary Utility Vehicles)  
TM  
TM  
Please Enter Information Below and Save For Future Reference.  
Date Purchased: __________________________  
Model Number: __________________________  
WHAT IS COVERED:  
From (Dealer): _____________________________________  
Serial Number: _____________________________________  
TM  
TM  
Woods Equipment Company (“WOODS”) warrants Mow’n Machine zero-turn mowers and attachments and Woods Boundary utility  
vehicles, accessories and attachments to be free from defect in material and workmanship for the warranty periods listed below.  
FOR HOW LONG:  
Mow’n Machine Model #CZ2136B, CZ1736K, CZ1942K, CZ1948K, CZ1952K, FE21B, FZ23B, FZ25D, FZ28K, ME2052B, MZ1952K,  
MZ2652G, MZ2561K, MZ2761, MZ3361G, MZ3372G, MZ2061YD & attachments are warranted for two (2) years from the date of  
delivery to the original purchaser or 2000 hours of operation, whichever occurs first.  
Mow’n Machine ME and MZ Series Models, serial number XXXXXXXX300 and above, Limited Lifetime Warranty on deck, deck cradle,  
and engine deck for the life of the machine to the original retail purchaser.  
Woods Boundary utility vehicle Model #MAV350, MAV480, MAV4x4, accessories & attachments are warranted for two (2) years from the  
date of delivery to the original purchaser.  
IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN  
DURATION TO THE DURATION OF THE WRITTEN WARRANTY PERIODS LISTED ABOVE. Some states do not allow limitations  
on how long an implied warranty lasts, so the above limitation may not apply to you.  
WHO IS COVERED:  
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer the  
product to a third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this  
Warranty.  
WHAT IS NOT COVERED:  
This Warranty does not cover normal wear or tear, or normal maintenance items, or any damage, failure or loss caused by:  
1. Improper operation, improper maintenance, misuse, or an accident;  
2. Any modification or repair by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS  
authorized service center; or  
3. Repairs made with parts other than those obtainable through WOODS.  
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by  
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.  
WHAT WOODS WILL DO TO CORRECT PROBLEMS:  
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if the  
product is defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of purchase within thirty  
(30) days after such defect or noncompliance is discovered or should have been discovered, routed through the dealer and distributor from  
whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or replacement within a reasonable time  
after WOODS receives the product.  
OTHER LIMITATIONS:  
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the  
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other  
legal theory. Without limiting the foregoing, WOODS shall not be liable for any damages relating to (i) lost profits, business, revenues or  
goodwill; (ii) any expense or loss incurred for labor, supplies, substitute machinery or rental; or (iii) any other type of damage to property  
or economic loss. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may  
not apply to you.  
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company, including without limitation,  
WOODS, its authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this Warranty.  
HOW STATE LAW APPLIES:  
This Warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.  
QUESTIONS:  
Answers to any questions regarding warranty service and locations may be obtained by contacting:  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
F-8045 MM & Boundary (Rev. 7/6/2007)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PART NO.  
MAN0115  
Woods Equipment  
Company  
2606 South Illinois Route 2  
Post Office Box 1000  
Oregon, Illinois 61061  
800-319-6637 tel  
800-399-6637 fax  
© 2001 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods  
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual  
are the property of their respective companies or mark holders. Specifications subject to change without notice.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

White Lawn Mower 134A676F190 User Manual
White Rodgers Thermostat 1F94 71 User Manual
Winegard TV Antenna TLS 600 User Manual
Wolfgang Puck Cookware Center Fill Bakeware Set User Manual
Wolf Oven WKECH1 User Manual
Yamaha CD Player CRW2100FXZ User Manual
Zanussi Cooktop EC19 User Manual
Zanussi Range ZCM 620 X User Manual
Zanussi Washer FL 816 A User Manual
Zebra Technologies Printer T402 User Manual