2104045
LOADER MOUNTING KIT
for LS84 Loader
®
on Kubota
B3200 Tractors
B3300SU Tractors
Includes Hose Kit
1019695
Tested. Proven. Unbeatable.
Download from Www.Somanuals.com. All Manuals Search And Download.
LOADER MOUNT INSTALLATION
CAUTION
■
Only use 2104045 Loader Mounting Kit for
„ Always wear relatively tight and belted clothing
to avoid getting caught in moving parts. Wear
sturdy, rough-soled work shoes and protective
equipment for eyes, hair, hands, hearing, and head;
and respirator or filter mask where appropriate.
mounting Woods LS84 loader on Kubota® B3200
and B3300SU tractors. Any other use or modifica-
tion of this mounting kit may result in serious
injury or death.
„ Safety instructions are important! Read all
attachment and power unit manuals; follow all
safety rules and safety decal information. (Replace-
ment manuals and safety decals are available from
your dealer. To locate your nearest dealer, check
or in the United States and Canada call 1-800-319-
6637.) Failure to follow instructions or safety rules
can result in serious injury or death.
NOTICE
■
This equipment must be assembled and
installed on the customer’s tractor by the Woods
dealer. Dealer must thoroughly inspect equipment
and complete each item on the PRE-DELIVERY
CHECK LIST, DELIVERY CHECK LIST, and PROD-
UCT REGISTRATION before equipment is released
to the customer.
■
Clean threaded holes in the tractor chassis
thoroughly using a tap of the proper size. Paint,
rust, or debris in the threads may not permit cap
screws to be installed and tightened correctly.
TRACTOR PREPARATION
For installing this mounting kit, references to right, left,
forward, and rearward directions are determined from
the operator’s position in the tractor seat.
NOTE: Leave all loader mount hardware loose until
mount is completely installed or otherwise instructed.
NOTE: 2104045 Loader Mounting Kit is compatible
with Kubota RCK 60-27BA and RC 72-27BA under-
mount mowers. See Kubota undermount mower man-
ual for installation instructions.
1. Shut off engine and set parking brake during
installation.
Figure 1. Remove Tractor Front Sub-Frame Brackets
2. Remove the tractor front weights if equipped.
(B3200)
3. Set the tractor wheels to the manufacturer’s wid-
est recommended spacing. Refer to the tractor
operator’s manual.
4. Remove tractor sub-frame brackets from both
sides of the tractor, shown in Figure 1.
As a valued customer, Woods appreciates your comments. Once loader mount and
hydraulic hoses have been installed, please take a few minutes to complete the Loader
Mount Evaluation sheet that was supplied with your loader mount. Your comments will
help us continue to bring you quality products.
(Rev. 4/25/2011)
MAN0807 (6/17/2009)
Mount Installation 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Right and Left loader Mounts
1. Attach right loader mount (1) to tractor frame
using two cap screws (10) and hardened flat
washers (12) in the forward top holes.
11
12
10
2. Insert cap screw (11) and hardened flat washer
12
(12) in the third and fourth hole.
3. Insert flange head cap screw (7) into the three
holes in tractor clutch housing. Use cap screw (6)
and washer (8) in the top rear slots to connect
loader mount to tractor frame. For three lower
slots, use hex flange screw (7) and hex flange nut
(9).
10
12
13
Tractor
Hardware
DP0001
4. Repeat step to install left rear mount (2). Note:
only 2 of item (6) are used on left mount.
Figure 2. Right Mount Installed
5. Place center plate (3) between right and left
mounts and secure using four (two per side) cap
screws (10), hardened flat washers (12) and hex
nuts (13).
6. Torque hardware to:
M14 x 1.5P x 40 mm . . . . . . . 87 lbs-ft (118 N-m)
M14 x 1.5P x 50 mm . . . . . . . 87 lbs-ft (118 N-m)
M12 x 1.75P x 35 mm . . . . . . . 70 lbs-ft (84 N-m)
M12 x 1.25P x 30 mm . . . . . . . 55 lbs-ft (75 N-m)
1. 1030978 Right mount
2. 1030979 Left mount
3. 1030986 Center plate
6.
7. 1028293 M12-1.75x35 CL10.9 Hex flange screw
8. 52177 .488 x 1.25 x .134 washer
9. 1028338 M12-1.75 CL10 Hex flange nut
65505 12 mm-1.25P x 30 mm HHCS
10.
64127 M14 x 1.5P x 40 mm HHCS
11.
12.
13.
65541 M14 x 1.5P x 50 mm
HHCS
46070 9/16 Hardened Flat
Washer
43104 M14 x 1.5 Hex Nut
Figure 3. 2104045 Mount Kit Installation
(Rev. 4/25/2011)
MAN0807 (6/17/2009)
4 Mount Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Install Grill Guard (Optional)
1. Attach grill guard (20) to front of tractor frame
using cap screws (10), hardened flat washers
(12), and hex nuts (13) as shown in Figure 4.
2. Torque hardware to:
M14-1.5P x 40mm HHCS . . . 87 lbs-ft (118 N-m)
20. 1031140 Grill guard
(includes items 10, 12 & 13)
10.
12.
13.
64127 M14 x 1.5P x 40 mm HHCS
46070 9/16 Hardened Flat Washer
43104 M14 x 1.5P Hex Nut
Figure 4. Grill Guard Installation
Mount Installation 5
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
1019695 HOSE KIT INSTALLATION
„ Keep hands and body away from pressurized
„ Protective hose sleeves must cover all hydrau-
lic hoses within 20 inches of the operator and be
secured onto metal hose fittings. Replace hoses or
sleeves if damaged or if protective sleeve cannot
be properly positioned or secured.
lines. Use paper or cardboard, not hands or other
body parts to check for leaks. Wear safety goggles.
Hydraulic fluid under pressure can easily penetrate
skin and will cause serious injury or death.
„ Make sure that all operating and service person-
nel know that if hydraulic fluid penetrates skin, it
must be surgically removed as soon as possible by
a doctor familiar with this form of injury or gan-
grene, serious injury, or death will result. CON-
TACT A PHYSICIAN IMMEDIATELY IF FLUID
ENTERS SKIN OR EYES. DO NOT DELAY.
„ Make sure all hydraulic hoses, fittings, and
valves are in good condition and not leaking before
starting power unit or using equipment. Check and
route hoses carefully to prevent damage. Hoses
must not be twisted, bent sharply, kinked, frayed,
pinched, or come into contact with any moving
parts. Operate moveable components through full
operational range to check clearances. Replace
any damaged hoses immediately.
„ Air in hydraulic systems can cause erratic oper-
ation and allows loads or equipment components
to drop unexpectedly. When connecting equipment
or hoses or performing any hydraulic maintenance,
purge any air in hydraulic system by operating all
hydraulic functions several times. Do this before
putting into service or allowing anyone to
approach the equipment.
General Description
These instructions are for operating the loader using
the tractor hydraulic remote control lever and four
hydraulic couplers located in front of the operator’s
platform.
DP3
Figure 5. Tractor Hydraulic Couplers
Hydraulic Installation 6
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Attach Loader Supply Hoses
1. Attach female quick couplers (2) to the loader
1. 360220 Hose, 38" x 1/4 NPTM x 9/16 JICM
2. 1019696 Quick coupler, female
supply hoses (1).
2. Attach loader supply hoses to the loader steel
feedlines on the loader boom. See Figure 6.
Figure 6. Loader Feedline Connections
Connect Loader Supply Hoses
3. Hoses must be routed so that they are not
pinched, bent sharply, or chafed during operation.
Hoses must not interfere with any tractor control
operation or contact any moving parts.
1. Route hydraulic hoses along loader mount and
connect to tractor hydraulic couplers, located
between right loader mount and tractor.
2. Be sure to avoid contact with clutch pedal and
4. Connect loader supply hoses to tractor hydraulics
other moveable tractor components.
as shown in Figure 7.
Figure 7. Loader Supply Hose Connections
7 Hydraulic Installation
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
Verify Control Movements
1. Mount loader to tractor: Remove mount pins
from loader uprights. Align tractor with loader and
slowly drive tractor into loader. Shut off tractor.
2. Connect loader feedline hoses to tractor hydraulic
couplers. See Figure 7.
3. Comply with all safety rules and start the tractor.
4. Mount loader to tractor by activating bucket cylin-
ders to raise or lower the loader uprights into the
loader mounts. Slowly advance tractor forward,
activating appropriate cylinders to engage loader
completely into mounts. Insert mounting pins to
secure loader.
●
●
●
●
●
Handle forward - Boom down
Handle forward to limit - Float position
Handle back - Boom up
5. Check that all tractor hydraulic control lever posi-
tions operate the loader movements correctly.
See Figure 8.
Handle to right - Dump bucket or attachment
Handle to left - Rollback bucket or attachment
6. If loader movements do not respond correctly,
shut off tractor, relieve pressure, and reconnect
properly. Loader control movements must be cor-
rect before proceeding.
Figure 8. Single Lever Control Operation
7. Once all loader functions are correct, start the
tractor and operate the loader to check for leaks.
Purge any remaining air from the hydraulic sys-
tem and check oil level.
8. When hose routings and correct loader opera-
tions are verified, identify each circuit by placing a
matching colored band around the male and
female quick-disconnect coupler. The color-coded
bands will make reinstallation easier when the
loader is removed from tractor.
9. Be sure that adequate slack is left in the hoses so
they can move as the loader moves through its
full range of motion.
10. Attach the plastic tie straps (included in kit) every
20 inches around the hoses to keep them tightly
bundled and away from contact with the ground
or other moving parts on the tractor or loader.
11. Before operating the loader, make sure that the
Pre-Delivery, Delivery, and Pre-Operation Check
Lists in the Loader Operator’s Manual have been
completed.
Hydraulic Installation 8
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
9 Hydraulic Installation
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
2104045 LOADER MOUNTING KIT
REF PART
QTY
DESCRIPTION
REF PART
QTY
64127 12 M14 x 1.5P x 40 mm HHCS
65541 M14 X 1.5P x 50 mm HHCS
46070 20 9/16 Hardened Flat Washer
DESCRIPTION
1
2
3
6
7
8
9
1030978
1030979
1030986
65505
1
1
1
5
Right Mount
Left Mount
10
11
12
13
4
Center Plate
12 mm-1.25P x 30 mm HHCS
43104
8
1
M14 x 1.5 Hex Nut
1028293 12 M12-1.75x35 CL10.9 Hex flange screw
20 1031140
Grill Guard (optional)
(includes items 10, 12, & 13)
52177
5
6
.488 x 1.25 x .134 HT washer
M12-1.75 CL10 Hex flange nut
1028338
HHCS Hex Head Cap Screw
(Rev. 4/25/2011)
Parts 10
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
1019695 HOSE KIT
REF PART
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
360220
4
4
1
1
1
1
1
2
Hose, 38" x 1/4 NPTM x 9/16 JICM
Quick coupler, female
1019696
395061
395062
56061
Plastic band, red (not shown)
Plastic band, blue (not shown
Plastic band, green (not shown)
Plastic band, yellow (not shown)
Plastic band, white (not shown)
Plastic tie, (not shown)
56062
54124
88 *
* Standard hardware, obtain locally
™
11 Parts
MAN0807 (6/17/2009)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT TORQUE CHART
Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific
application.
Fasteners must always be replaced with the same grade as specified in the manual parts list.
Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware.
Make sure fastener threads are clean and you start thread engagement properly.
All torque values are given to specifications used on hardware defined by SAE J1701 MAR 99 & J1701M JUL 96.
SAE Bolt Head
Identification
SAE SERIES
TORQUE
CHART
A
SAE Grade 2
(No Dashes)
SAE Grade 8
(6 Radial Dashes)
SAE Grade 5
(3 Radial Dashes)
MARKING ON HEAD
A
SAE 2
SAE 5
SAE 8
Diameter
(Inches)
Wrench
Size
lbs-ft
N-m
8
lbs-ft
10
N-m
13
lbs-ft
14
N-m
1/4"
5/16"
3/8"
7/16"
1/2"
9/16"
5/8"
3/4"
7/8"
1"
7/16"
1/2"
6
18
37
12
17
19
26
27
9/16"
5/8"
23
31
35
47
49
67
36
48
55
75
78
106
163
232
325
569
907
1383
3/4"
55
75
85
115
164
230
403
642
979
120
171
240
420
669
1020
13/16"
15/16"
1-1/8"
1-5/16"
1-1/2"
78
106
149
261
416
634
121
170
297
474
722
110
192
306
467
METRIC SERIES
TORQUE
CHART
8.8
Metric Bolt Head
Identification
10.9
A
Metric
Grade 8.8
Metric
Grade 10.9
COARSE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
FINE THREAD
MARKING ON HEAD
Metric 8.8 Metric 10.9
N-m lbs-ft
A
A
Diameter &
Thread Pitch Wrench
(Millimeters)
Diameter &
Thread Pitch
(Millimeters)
Size
N-m
lbs-ft
6
N-m
lbs-ft
6
6 x 1.0
10 mm
13 mm
16 mm
18 mm
21 mm
24 mm
27 mm
30 mm
34 mm
36 mm
46 mm
8
11
27
8
8
11
29
8
6 x 1.0
8 x 1.0
8 x 1.25
10 x 1.5
12 x 1.75
14 x 2.0
16 x 2.0
18 x 2.5
20 x 2.5
22 x 2.5
24 x 3.0
30 x 3.0
20
15
20
21
16
22
39
29
54
40
41
30
57
42
10 x 1.25
12 x 1.25
14 x 1.5
16 x 1.5
18 x 1.5
20 x 1.5
22 x 1.5
24 x 2.0
30 x 2.0
68
50
94
70
75
55
103
163
250
363
507
684
861
1740
76
109
169
234
330
451
571
1175
80
151
234
323
457
623
790
1626
111
173
239
337
460
583
1199
118
181
263
367
495
623
1258
87
120
184
268
374
505
635
1283
125
172
244
332
421
867
133
194
270
365
459
928
Typical Washer
Installations
Bolt
Flat Washer
Lock Washer
8/9/00
Appendix 12
Bolt Torque & Size Charts (Rev. 3/28/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
BOLT SIZE CHART
NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts.
SAE Bolt Thread Sizes
5/16
3/8
1/2
5/8
3/4
7/8
IN
1
2
7
3
4
5
6
MM
25
50
75
100
125
150
175
Metric Bolt Thread Sizes
8MM 10MM
12MM
14MM
16MM
18MM
ABBREVIATIONS
AG .............................................................. Agriculture
MPa ........................................................ Mega Pascal
N ......................................................................Newton
NC...................................................... National Coarse
NF...........................................................National Fine
NPSM .................... National Pipe Straight Mechanical
NPT...........................................National Pipe Tapered
NPT SWF......... National Pipe Tapered Swivel Female
ORBM...........................................O-Ring Boss - Male
P .......................................................................... Pitch
PBY.......................................................Power-Beyond
psi ......................................... Pounds per Square Inch
PTO......................................................Power Take Off
QD ................................................... Quick Disconnect
RH.............................................................. Right Hand
ROPS........................... Roll-Over Protective Structure
RPM........................................Revolutions Per Minute
RT ........................................................................Right
SAE.......................... Society of Automotive Engineers
UNC..................................................... Unified Coarse
UNF ..........................................................Unified Fine
UNS ..................................................... Unified Special
ASABE ....................American Society of Agricultural &
Biological Engineers (formerly ASAE)
ASAE....... American Society of Agricultural Engineers
ATF................................Automatic Transmission Fluid
BSPP............................. British Standard Pipe Parallel
BSPTM................ British Standard Pipe Tapered Male
CV ....................................................Constant Velocity
CCW.............................................. Counter-Clockwise
CW .............................................................. Clockwise
F.......................................................................Female
FT.............................................................. Full Thread
GA .....................................................................Gauge
GR (5, etc.)........................................... Grade (5, etc.)
HHCS ........................................Hex Head Cap Screw
HT ...........................................................Heat-Treated
JIC.................Joint Industry Council 37° Degree Flare
LH................................................................. Left Hand
LT ...........................................................................Left
m ........................................................................ Meter
mm ............................................................... Millimeter
M ..........................................................................Male
13 Appendix
Bolt Torque & Size Charts (Rev. 3/28/2007)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
All Models Except Mow’n MachineTM Zero-Turn Mowers
Please Enter Information Below and Save for Future Reference.
Date Purchased: ____________________________
Model Number: ____________________________
From (Dealer): __________________________________________
Serial Number: __________________________________________
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and workmanship. Except as otherwise set forth
below, the duration of this Warranty shall be for TWELVE (12) MONTHS COMMENCING ON THE DATE OF DELIVERY OF THE
PRODUCT TO THE ORIGINAL PURCHASER.
All current model loaders and backhoes are warranted for two (2) years from the date of delivery to the original purchaser.
The warranty periods for specific parts or conditions are listed below:
Part or
Condition
Warranted
Duration (from date of
delivery to the original
purchaser)
Model Number
Gearbox
Seals
All units listed below
2 years
BW1260, BW1620, BW1800, BW2400
8 years
7 years
BW240HD, BW180HD, BW180HB, BW126HB
BB48X, BB60X, BB72X, BB84X, BB600X, BB720X, BB840X, BB6000X, BB7200X, BB8400X,
DS1260, DSO1260, DS1440, TS1680, BW126-3, BW180-3, BW240
6 years
Gearbox
components PHD25, PHD35, PHD65, PHD95, 2162, 3240, DS96, DS120, RCC42, RM550-2, RM660-2,
RD990X, PRD6000, PRD7200, PRD8400, S15CD, S20CD, S22CD, S25CD, S27CD, BW180LH, 5 years
TC/R74, TC/R68, TC/R60, TBW144, TBW180, TBW204
3 years (1 year if used in rental or
commercial applications)
RDC54, RD60, RD72, TBW150C, TS/R60, TS/R52, TS/R44
Blade
spindles
RM550-2, RM660-2, RD990X, PRD6000, PRD7200, PRD8400, TBW144, TBW180, TBW204
BB600, BB720, BB840, BB6000, BB7200, BB8400, BW126-3, BW126HB, BW180-3, BW180HB,
3 years
Rust-through BW180HD, BW1260, BW1800, BW240, BW240HD, 2162, 3240, DS1260, DSO1260, DS1440, 10 years
TS1680
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of WOODS, has been subjected to
improper operation, improper maintenance, misuse, or an accident. This Warranty does not apply in the event that the product has been materially
modified or repaired by someone other than WOODS, a WOODS authorized dealer or distributor, and/or a WOODS authorized service center.
This Warranty does not cover normal wear or tear, or normal maintenance items. This Warranty also does not cover repairs made with parts other
than those obtainable through WOODS.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell or otherwise transfer this product to a
third party, this Warranty does not transfer to the third party purchaser in any way. There are no third party beneficiaries of this Warranty.
WOODS makes no warranty, express or implied, with respect to engines, batteries, tires or other parts or accessories not manufactured by
WOODS. Warranties for these items, if any, are provided separately by their respective manufacturers.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of charge, of the product if WOODS, in
its sole discretion, deems it to be defective or in noncompliance with this Warranty. The product must be returned to WOODS with proof of
purchase within thirty (30) days after such defect or noncompliance is discovered or should have been discovered, routed through the
dealer and distributor from whom the purchase was made, transportation charges prepaid. WOODS shall complete such repair or
replacement within a reasonable time after WOODS receives the product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY.
THE REMEDY OF REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF THIS WARRANTY. WOODS
MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY
OF MERCHANTABILITY AND/OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising directly or indirectly from the
product, whether such claim is based upon breach of contract, breach of warranty, negligence, strict liability in tort or any other legal
theory. Without limiting the generality of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues
or goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for labor, supplies, substitute machinery or
rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to obtain materials or manufacture
replacement parts.
No agent, representative, dealer, distributor, serviceperson, salesperson, or employee of any company, including without limitation, WOODS, its
authorized dealers, distributors, and service centers, is authorized to alter, modify, or enlarge this
Warranty. Answers to any questions regarding warranty
service and locations may be obtained by contacting:
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061 USA
800-319-6637 tel
800-399-6637 fax
F-3079 (Rev. 2/14/2011)
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
(Replacement Parts For All Models Except Mow’n Machine
Zero-Turn Mowers and Woods Boundary Utility Vehicles)
TM
TM
Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material and
workmanship for a period of ninety (90) days from the date of delivery of the product to the original
purchaser with the exception of V-belts, which will be free of defect in material and workmanship for a
period of 12 months.
Under no circumstances will this Warranty apply in the event that the product, in the good faith opinion of
WOODS, has been subjected to improper operation, improper maintenance, misuse, or an accident. This
Warranty does not cover normal wear or tear, or normal maintenance items.
This Warranty is extended solely to the original purchaser of the product. Should the original purchaser sell
or otherwise transfer this product to a third party, this Warranty does not transfer to the third party purchaser
in any way. There are no third party beneficiaries of this Warranty.
WOODS’ obligation under this Warranty is limited to, at WOODS’ option, the repair or replacement, free of
charge, of the product if WOODS, in its sole discretion, deems it to be defective or in noncompliance with
this Warranty. The product must be returned to WOODS with proof of purchase within thirty (30)
days after such defect or noncompliance is discovered or should have been discovered, routed through
the dealer and distributor from whom the purchase was made, transportation charges prepaid.
WOODS shall complete such repair or replacement within a reasonable time after WOODS receives the
product. THERE ARE NO OTHER REMEDIES UNDER THIS WARRANTY. THE REMEDY OF
REPAIR OR REPLACEMENT IS THE SOLE AND EXCLUSIVE REMEDY UNDER THIS
WARRANTY.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE OF
THIS WARRANTY. WOODS MAKES NO OTHER WARRANTY, EXPRESS OR IMPLIED, AND
WOODS SPECIFICALLY DISCLAIMS ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/
OR ANY IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WOODS shall not be liable for any incidental or consequential losses, damages or expenses, arising
directly or indirectly from the product, whether such claim is based upon breach of contract, breach
of warranty, negligence, strict liability in tort or any other legal theory. Without limiting the generality
of the foregoing, Woods specifically disclaims any damages relating to (i) lost profits, business, revenues or
goodwill; (ii) loss of crops; (iii) loss because of delay in harvesting; (iv) any expense or loss incurred for
labor, supplies, substitute machinery or rental; or (v) any other type of damage to property or economic loss.
This Warranty is subject to any existing conditions of supply which may directly affect WOODS’ ability to
obtain materials or manufacture replacement parts.
No agent, representative, dealer, distributor, service person, salesperson, or employee of any company,
including without limitation, WOODS, its authorized dealers, distributors, and service centers, is authorized
to alter, modify, or enlarge this Warranty.
Answers to any questions regarding warranty service and locations may be obtained by contacting:
F-8494 (Rev. 6/23/2005)
Download from Www.Somanuals.com. All Manuals Search And Download.
MAN0807
Woods Equipment
Company
2606 South Illinois Route 2
Post Office Box 1000
Oregon, Illinois 61061
815-732-2141 tel
815-732-7580 fax
© 1994 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trademarks of Woods
Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual
are the property of their respective companies or mark holders. Specifications subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|