Winegard Power Supply RV 7012 User Manual

Alternatively, Customer may ship the product prepaid to  
Winegard Technical Services (located at 3111 Kirkwood  
Street, Burlington, Iowa 52601, Telephone 800-788-  
4417). Customer must return the product along with a brief  
description of the problem and provide Winegard Technical  
Services with Customer’s name, address, and phone number.  
Customer must also provide proof of purchase to verify the  
product is under warranty. If the product is returned before the  
expiration of the warranty period, Winegard Company will (at  
its option) either repair or replace the product.  
INSTALLING FC-5910  
CONNECTORS ON COAX CABLE  
STEP 5. Mount power supply in wall with  
screwsprovidedandattachTVsetcabletojack  
on front. Connect band separator to VHF and  
UHF antenna terminals of TV set, if required.  
Press switch on front of outlet and check that  
light is on.  
INSTRUCTIONS  
This Limited Warranty does not apply if the product has been  
damaged, deteriorates, malfunctions or fails from: improper  
installation, misuse, abuse, neglect, accident, tampering,  
modification of the product as originally manufactured by  
Winegard in any manner whatsoever, removing or defacing  
any serial number, usage not in accordance with product  
instructions or acts of nature such as damage caused by  
wind, lightning, ice or corrosive environments such as salt  
spray and acid rain. This Limited Warranty also does not  
apply if the product becomes unable to perform its’ intended  
function in any way as a result of the television signal provider  
making any changes in technology or service.  
Figure 4  
MODELS RV-7012, RV-7032, RV-7042  
Made in U.S.A.  
Figure 5  
STEP 1: Strip outer cover back 1/2"* from end of cable. Fray  
braid back as far as outer cover will allow.  
RV WALL PLATE/  
POWER SUPPLY  
STEP 2: Trim braid close to outer cover and remove 1/4"* of  
inner insulation being careful not to nick center conductor.  
Make sure no foil or braid can touch center conductor.  
Set 2  
This unit is equipped with a polyswitch,  
(current limiting device), which will shut down  
+12VDC if there is a direct short between  
antennaandpowersupply.Greenindicatorlight  
willnotlight.Onceshortiseliminated,devicewill  
reset itself in approximately 2 minutes.  
STEP 3: Slideconnectortipbetweenbraidandinnerinsulation  
(braidandfoil, onfoilshieldcable)andpushconnectoroncable  
as far as it will go. Crimp built-in ferrule with proper crimping  
tool.Hexconnectorrequireshexcrimpingtool.DoNotcrush  
cable out-of-round. * If installing in very hot weather, increase  
these dimensions 1/8".  
RETURN AUTHORIZATION POLICY  
A Return Material Authorization (RMA) is required prior to  
returning any product to Winegard Company or Winegard  
Warranty Services under this warranty policy. Please call our  
Technical Services Department at 800-788-4417 or send an  
e-mail to [email protected] to obtain the RMA number.  
Please furnish the date of purchase when requesting an RMA  
number. Enclose the product in a prepaid package and  
write the RMA number in large, clear letters on the outside  
of the package. To avoid confusion or misunderstanding, a  
shipment(s) without an RMA number(s) or an unauthorized  
return(s) will be refused and returned to Customer freight  
collect.  
WINEGARD COMPANY DOES NOT ASSUME ANY  
LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS  
OR IMPLIED, MADE BY ANY OTHER PERSON.  
ALLOTHERWARRANTIESWHETHEREXPRESS, IMPLIED  
OR STATUTORY INCLUDING WARRANTIES OF FITNESS  
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY  
ARE LIMITED TO THE TWO YEAR PERIOD OF THIS  
WARRANTY.  
In states that do not allow limitations on implied warranties,  
or the exclusion of limitation of incidental or consequential  
damages, the above limitations or exclusions do not apply.  
Some states do not allow limitations on how long an implied  
warranty lasts, or the exclusion of limitation of incidental  
or consequential damages, so the above limitations or  
exclusions may not apply to you.  
This warranty gives Customer specific legal rights.  
Customer may also have other rights that may vary from  
state to state.  
Antenna  
Cable  
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY  
(2 YEARS PARTS; 1 YEAR LABOR)  
Winegard Company warrants this product against defects in  
materials or workmanship for a period of two (2) years from the  
date of original purchase. During year one (1) of such warranty,  
Winegard Company will also pay authorized labor costs to an  
authorized Winegard dealer to repair or replace defective  
products. No warranty claim will be honored unless at the time  
the claim is made, Customer presents proof of purchase to an  
authorized Winegard dealer (to locate the nearest authorized  
Winegard dealer, contact Winegard Company, 3000 Kirkwood  
Street, Burlington, Iowa 52601, Telephone 800-288-8094 or  
purchase with a dated sales receipt for the Winegard product  
to verify the product is under warranty. If the date of purchase  
cannot be verified, the warranty period shall be considered to  
begin thirty (30) days after the date of manufacture.  
DESCRIPTION  
OPERATION: To receive cable signals from  
outdoor receptacle: Press switch to OFF  
(CABLE) position. Light on wall plate will go off  
showing that power is no longer connected to  
the antenna and that bothTV sets are receiving  
signals from outdoor receptacle.  
Wall plate/power supply to operate Winegard  
RV antenna with outdoor receptacle for TV  
set and cable input. Wall plate/power supply  
provides +12VDC to antenna and +12 volt  
receptacle as well as antenna signals to two  
TV sets. Cable input from outdoor receptacle  
connects to wall plate and may be switched so  
eitherantennaorcablesignalsmaybewatched.  
See applications.  
To receive signals from antenna: Press  
switch to ON (ANT) position. Light on wallplate  
will come on showing that power is connected  
to the antenna and both TV sets are receiving  
signals from the antenna.  
If a defect in material or workmanship is discovered, Customer  
may take the product to an authorized Winegard dealer for  
service. Customer must provide proof of purchase to verify  
the product is under warranty. If the product is brought to an  
authorized Winegard dealer for service prior to expiration of  
year one (1) of the warranty period and a defect in material  
or workmanship is verified by Winegard Technical Services,  
Winegard Company will cover the Winegard dealer’s labor  
charges for warranty service. The Winegard dealer must  
contact Winegard Technical Services in advance for pre-  
approval of the service. Approval of the service is at the sole  
discretion of Winegard Company.  
NOTE:THISUNITISNOTANAMPLIFIER.USEONLY  
WITH A WINEGARD AMPLIFIED RV ANTENNA.  
NOTE: Make sure the antenna is in the  
operating position (up) and pointed at the  
station desired.  
SATELLITE RECEIVER WARRANTY  
See manufacturer’s limited warranty policy.  
WS-MOBWARREREV 2 Rev.1/10  
WINEGARD COMPANY  
3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000  
Printed in U.S.A. 2451486 Rev.2 1/10  
Alternatively, Customer may ship the product prepaid to  
Winegard Technical Services (located at 3111 Kirkwood  
Street, Burlington, Iowa 52601, Telephone 800-788-  
4417). Customer must return the product along with a brief  
description of the problem and provide Winegard Technical  
Services with Customer’s name, address, and phone number.  
Customer must also provide proof of purchase to verify the  
product is under warranty. If the product is returned before the  
expiration of the warranty period, Winegard Company will (at  
its option) either repair or replace the product.  
INSTALLING FC-5910  
CONNECTORS ON COAX CABLE  
STEP 5. Mount power supply in wall with  
screwsprovidedandattachTVsetcabletojack  
on front. Connect band separator to VHF and  
UHF antenna terminals of TV set, if required.  
Press switch on front of outlet and check that  
light is on.  
INSTRUCTIONS  
This Limited Warranty does not apply if the product has been  
damaged, deteriorates, malfunctions or fails from: improper  
installation, misuse, abuse, neglect, accident, tampering,  
modification of the product as originally manufactured by  
Winegard in any manner whatsoever, removing or defacing  
any serial number, usage not in accordance with product  
instructions or acts of nature such as damage caused by  
wind, lightning, ice or corrosive environments such as salt  
spray and acid rain. This Limited Warranty also does not  
apply if the product becomes unable to perform its’ intended  
function in any way as a result of the television signal provider  
making any changes in technology or service.  
Figure 4  
MODELS RV-7012, RV-7032, RV-7042  
Made in U.S.A.  
Figure 5  
STEP 1: Strip outer cover back 1/2"* from end of cable. Fray  
braid back as far as outer cover will allow.  
RV WALL PLATE/  
POWER SUPPLY  
This unit is equipped with a polyswitch,  
(current limiting device), which will shut down  
+12VDC if there is a direct short between  
antennaandpowersupply.Greenindicatorlight  
willnotlight.Onceshortiseliminated,devicewill  
reset itself in approximately 2 minutes.  
STEP 2: Trim braid close to outer cover and remove 1/4"* of  
inner insulation being careful not to nick center conductor.  
Make sure no foil or braid can touch center conductor.  
Set 2  
STEP 3: Slideconnectortipbetweenbraidandinnerinsulation  
(braidandfoil, onfoilshieldcable)andpushconnectoroncable  
as far as it will go. Crimp built-in ferrule with proper crimping  
tool.Hexconnectorrequireshexcrimpingtool.DoNotcrush  
cable out-of-round. * If installing in very hot weather, increase  
these dimensions 1/8".  
RETURN AUTHORIZATION POLICY  
A Return Material Authorization (RMA) is required prior to  
returning any product to Winegard Company or Winegard  
Warranty Services under this warranty policy. Please call our  
Technical Services Department at 800-788-4417 or send an  
e-mail to [email protected] to obtain the RMA number.  
Please furnish the date of purchase when requesting an RMA  
number. Enclose the product in a prepaid package and  
write the RMA number in large, clear letters on the outside  
of the package. To avoid confusion or misunderstanding, a  
shipment(s) without an RMA number(s) or an unauthorized  
return(s) will be refused and returned to Customer freight  
collect.  
WINEGARD COMPANY DOES NOT ASSUME ANY  
LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS  
OR IMPLIED, MADE BY ANY OTHER PERSON.  
ALLOTHERWARRANTIESWHETHEREXPRESS, IMPLIED  
OR STATUTORY INCLUDING WARRANTIES OF FITNESS  
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY  
ARE LIMITED TO THE TWO YEAR PERIOD OF THIS  
WARRANTY.  
In states that do not allow limitations on implied warranties,  
or the exclusion of limitation of incidental or consequential  
damages, the above limitations or exclusions do not apply.  
Some states do not allow limitations on how long an implied  
warranty lasts, or the exclusion of limitation of incidental  
or consequential damages, so the above limitations or  
exclusions may not apply to you.  
This warranty gives Customer specific legal rights.  
Customer may also have other rights that may vary from  
state to state.  
Antenna  
Cable  
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY  
(2 YEARS PARTS; 1 YEAR LABOR)  
Winegard Company warrants this product against defects in  
materials or workmanship for a period of two (2) years from the  
date of original purchase. During year one (1) of such warranty,  
Winegard Company will also pay authorized labor costs to an  
authorized Winegard dealer to repair or replace defective  
products. No warranty claim will be honored unless at the time  
the claim is made, Customer presents proof of purchase to an  
authorized Winegard dealer (to locate the nearest authorized  
Winegard dealer, contact Winegard Company, 3000 Kirkwood  
Street, Burlington, Iowa 52601, Telephone 800-288-8094 or  
purchase with a dated sales receipt for the Winegard product  
to verify the product is under warranty. If the date of purchase  
cannot be verified, the warranty period shall be considered to  
begin thirty (30) days after the date of manufacture.  
DESCRIPTION  
OPERATION: To receive cable signals from  
outdoor receptacle: Press switch to OFF  
(CABLE) position. Light on wall plate will go off  
showing that power is no longer connected to  
the antenna and that bothTV sets are receiving  
signals from outdoor receptacle.  
Wall plate/power supply to operate Winegard  
RV antenna with outdoor receptacle for TV  
set and cable input. Wall plate/power supply  
provides +12VDC to antenna and +12 volt  
receptacle as well as antenna signals to two  
TV sets. Cable input from outdoor receptacle  
connects to wall plate and may be switched so  
eitherantennaorcablesignalsmaybewatched.  
See applications.  
To receive signals from antenna: Press  
switch to ON (ANT) position. Light on wallplate  
will come on showing that power is connected  
to the antenna and both TV sets are receiving  
signals from the antenna.  
If a defect in material or workmanship is discovered, Customer  
may take the product to an authorized Winegard dealer for  
service. Customer must provide proof of purchase to verify  
the product is under warranty. If the product is brought to an  
authorized Winegard dealer for service prior to expiration of  
year one (1) of the warranty period and a defect in material  
or workmanship is verified by Winegard Technical Services,  
Winegard Company will cover the Winegard dealer’s labor  
charges for warranty service. The Winegard dealer must  
contact Winegard Technical Services in advance for pre-  
approval of the service. Approval of the service is at the sole  
discretion of Winegard Company.  
NOTE:THISUNITISNOTANAMPLIFIER.USEONLY  
WITH A WINEGARD AMPLIFIED RV ANTENNA.  
NOTE: Make sure the antenna is in the  
operating position (up) and pointed at the  
station desired.  
SATELLITE RECEIVER WARRANTY  
See manufacturer’s limited warranty policy.  
WS-MOBWARREREV 2 Rev.1/10  
WINEGARD COMPANY  
3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000  
Printed in U.S.A. 2451486 Rev.2 1/10  
Alternatively, Customer may ship the product prepaid to  
Winegard Technical Services (located at 3111 Kirkwood  
Street, Burlington, Iowa 52601, Telephone 800-788-  
4417). Customer must return the product along with a brief  
description of the problem and provide Winegard Technical  
Services with Customer’s name, address, and phone number.  
Customer must also provide proof of purchase to verify the  
product is under warranty. If the product is returned before the  
expiration of the warranty period, Winegard Company will (at  
its option) either repair or replace the product.  
INSTALLING FC-5910  
CONNECTORS ON COAX CABLE  
STEP 5. Mount power supply in wall with  
screwsprovidedandattachTVsetcabletojack  
on front. Connect band separator to VHF and  
UHF antenna terminals of TV set, if required.  
Press switch on front of outlet and check that  
light is on.  
INSTRUCTIONS  
This Limited Warranty does not apply if the product has been  
damaged, deteriorates, malfunctions or fails from: improper  
installation, misuse, abuse, neglect, accident, tampering,  
modification of the product as originally manufactured by  
Winegard in any manner whatsoever, removing or defacing  
any serial number, usage not in accordance with product  
instructions or acts of nature such as damage caused by  
wind, lightning, ice or corrosive environments such as salt  
spray and acid rain. This Limited Warranty also does not  
apply if the product becomes unable to perform its’ intended  
function in any way as a result of the television signal provider  
making any changes in technology or service.  
Figure 4  
MODELS RV-7012, RV-7032, RV-7042  
Made in U.S.A.  
Figure 5  
STEP 1: Strip outer cover back 1/2"* from end of cable. Fray  
braid back as far as outer cover will allow.  
RV WALL PLATE/  
POWER SUPPLY  
This unit is equipped with a polyswitch,  
(current limiting device), which will shut down  
+12VDC if there is a direct short between  
antennaandpowersupply.Greenindicatorlight  
willnotlight.Onceshortiseliminated,devicewill  
reset itself in approximately 2 minutes.  
STEP 2: Trim braid close to outer cover and remove 1/4"* of  
inner insulation being careful not to nick center conductor.  
Make sure no foil or braid can touch center conductor.  
Set 2  
STEP 3: Slideconnectortipbetweenbraidandinnerinsulation  
(braidandfoil, onfoilshieldcable)andpushconnectoroncable  
as far as it will go. Crimp built-in ferrule with proper crimping  
tool.Hexconnectorrequireshexcrimpingtool.DoNotcrush  
cable out-of-round. * If installing in very hot weather, increase  
these dimensions 1/8".  
RETURN AUTHORIZATION POLICY  
A Return Material Authorization (RMA) is required prior to  
returning any product to Winegard Company or Winegard  
Warranty Services under this warranty policy. Please call our  
Technical Services Department at 800-788-4417 or send an  
e-mail to [email protected] to obtain the RMA number.  
Please furnish the date of purchase when requesting an RMA  
number. Enclose the product in a prepaid package and  
write the RMA number in large, clear letters on the outside  
of the package. To avoid confusion or misunderstanding, a  
shipment(s) without an RMA number(s) or an unauthorized  
return(s) will be refused and returned to Customer freight  
collect.  
WINEGARD COMPANY DOES NOT ASSUME ANY  
LIABILITIES FOR ANY OTHER WARRANTIES, EXPRESS  
OR IMPLIED, MADE BY ANY OTHER PERSON.  
ALLOTHERWARRANTIESWHETHEREXPRESS, IMPLIED  
OR STATUTORY INCLUDING WARRANTIES OF FITNESS  
FOR A PARTICULAR PURPOSE AND MERCHANTABILITY  
ARE LIMITED TO THE TWO YEAR PERIOD OF THIS  
WARRANTY.  
In states that do not allow limitations on implied warranties,  
or the exclusion of limitation of incidental or consequential  
damages, the above limitations or exclusions do not apply.  
Some states do not allow limitations on how long an implied  
warranty lasts, or the exclusion of limitation of incidental  
or consequential damages, so the above limitations or  
exclusions may not apply to you.  
This warranty gives Customer specific legal rights.  
Customer may also have other rights that may vary from  
state to state.  
Antenna  
Cable  
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY  
(2 YEARS PARTS; 1 YEAR LABOR)  
DESCRIPTION  
Winegard Company warrants this product against defects in  
materials or workmanship for a period of two (2) years from the  
date of original purchase. During year one (1) of such warranty,  
Winegard Company will also pay authorized labor costs to an  
authorized Winegard dealer to repair or replace defective  
products. No warranty claim will be honored unless at the time  
the claim is made, Customer presents proof of purchase to an  
authorized Winegard dealer (to locate the nearest authorized  
Winegard dealer, contact Winegard Company, 3000 Kirkwood  
Street, Burlington, Iowa 52601, Telephone 800-288-8094 or  
purchase with a dated sales receipt for the Winegard product  
to verify the product is under warranty. If the date of purchase  
cannot be verified, the warranty period shall be considered to  
begin thirty (30) days after the date of manufacture.  
OPERATION: To receive cable signals from  
outdoor receptacle: Press switch to OFF  
(CABLE) position. Light on wall plate will go off  
showing that power is no longer connected to  
the antenna and that bothTV sets are receiving  
signals from outdoor receptacle.  
Wallplate/powersupplytooperateWinegardRV  
antenna with outdoor receptacle for TV set and  
cable input. Wall plate/power supply provides  
+12VDC to antenna and +12 volt receptacle  
as well as antenna signals to two TV sets.  
Cable input from outdoor receptacle connects  
to wall plate and may be switched so either  
antenna or cable or signals may be watched.  
See applications.  
To receive signals from antenna: Press  
switch to ON (ANT) position. Light on wallplate  
will come on showing that power is connected  
to the antenna and both TV sets are receiving  
signals from the antenna.  
If a defect in material or workmanship is discovered, Customer  
may take the product to an authorized Winegard dealer for  
service. Customer must provide proof of purchase to verify  
the product is under warranty. If the product is brought to an  
authorized Winegard dealer for service prior to expiration of  
year one (1) of the warranty period and a defect in material  
or workmanship is verified by Winegard Technical Services,  
Winegard Company will cover the Winegard dealer’s labor  
charges for warranty service. The Winegard dealer must  
contact Winegard Technical Services in advance for pre-  
approval of the service. Approval of the service is at the sole  
discretion of Winegard Company.  
NOTE:THISUNITISNOTANAMPLIFIER.USEONLY  
WITH A WINEGARD AMPLIFIED RV ANTENNA.  
NOTE: Make sure the antenna is in the  
operating position (up) and pointed at the  
station desired.  
SATELLITE RECEIVER WARRANTY  
See manufacturer’s limited warranty policy.  
WS-MOBWARREREV 2 Rev.1/10  
WINEGARD COMPANY  
3000 KIRKWOOD ST., BURLINGTON, IA 52601-2000  
Printed in U.S.A. 2451486 Rev.2 1/10  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Welbilt Bread Maker ABM 4900 User Manual
Weslo Treadmill IMTL 159050 User Manual
Weslo Treadmill WETL347090 User Manual
Whirlpool Freezer EV181NZRQ User Manual
Whirlpool Trash Compactor GC900QPPB2 User Manual
Whynter Air Conditioner ARC 131GD User Manual
Williams Sound Headphones WIR RX14 User Manual
Yamaha Automobile Parts F200, LF200, F225, LF225 User Manual
Yamaha Electronic Keyboard DX7 II D User Manual
Zhone Technologies Network Router 6211 I3 xxx User Manual