HIGH SPEED BURNISHER
MODELS:
LB2000I
LB2000IA UB2000F LB2000
10090200 10090210 10090620 10090190
Operating Instructions (ENG)
86309600-B
01/29/09
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Machine Data Log/Overview................................2
Table of Contents.................................................3
HOW TO USE THIS MANUAL
How to use this Manual........................................1-1
SAFETY
Important Safety Instructions ...............................2-1
Hazard Intensity Level..........................................2-2
Grounding Instructions.........................................2-3
OPERATION
Technical Specifications.......................................3-1
Handle Installation................................................3-2
Operation..............................................................3-3
Pad Driver Installation..........................................3-3
MAINTENANCE
Machine Troubleshooting.....................................4-1
Wiring Diagram/Service Schedule .......................4-2
GROUP PARTS LIST
Deck Group..........................................................5-1
Electrical...............................................................5-3
Handle-Lower.......................................................5-5
Handle-Upper.......................................................5-7
Motor ....................................................................5-9
Pad/driver........................................................... 5-11
Wiring-120V ....................................................... 5-13
Wiring-230V ....................................................... 5-14
Suggested Spare Parts...................................... 5-15
3
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THIS MANUAL
This manual contains the following sections:
The OPERATIONS section is to familiarize the
operator with the operation and function of the
machine.
-
-
-
-
-
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The MAINTENANCE section contains preventive
maintenance to keep the machine and its
components in good working condition. They are
listed in this general order:
The HOW TO USE THIS MANUAL section will tell
you how to find important information for ordering
correct repair parts.
The PARTS LIST section contains assembled
parts illustrations and corresponding parts list. The
parts lists include a number of columns of
information:
Parts may be ordered from authorized dealers.
When placing an order for parts, the machine
model and machine serial number are important.
Refer to the MACHINE DATA box which is filled
out during the installation of your machine. The
MACHINE DATA box is located on the inside of
the front cover of this manual.
-
-
REF – column refers to the reference
number on the parts illustration.
PART NO. – column lists the part
number for the part.
-
-
PRV NO. - Reference No.
QTY – column lists the quantity of the
part used in that area of the machine.
DESCRIPTION – column is a brief
description of the part.
-
-
SERIAL NO. FROM – If this column
has an (*) and a Reference number,
see the SERIAL NUMBERS page in
the back of your manual. If column
has two asterisk (**), call manufacturer
for serial number. The serial number
indicates the first machine the part
number is applicable to. The main
illustration shows the most current
design of the machine. When a boxed
illustration is shown, it displays the
older design.
The SAFETY section contains important
information regarding hazard or unsafe practices
of the machine. Levels of hazards are identified
that could result in product or personal injury, or
severe injury resulting in death.
-
NOTES – column for information not
noted by the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement
parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the
front cover is the part number for this manual.
1-1
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To r educe the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water,
return it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce
airflow.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine
near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories,
shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
During operation, attention shall be paid to other persons, especially children.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, unplug the machine.
Do not handle the plug or machine with wet hands.
Do not unplug machine by pulling on cord. To unplug, grasp the plug, not the cord.
Do not use with damaged cord or plug. Follow all instructions in this manual concerning grounding the
machine.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or
corners.
Do not pull/run machine over cord. Keep cord away from heated surfaces.
Connect to a properly grounded outlet. See Grounding Instructions.
If the supply cord is damaged it must be replaced by a special cord from an authorized service agent.
Unplug before cleaning or servicing.
Operational hazard may occur when running the machine over the supply cord.
This appliance has been designed for use with pads specified by the manufacturer. The fitting of other pads
may affect its safety.
This machine is for dry use only and shall not be used or stored outdoors in wet conditions.
SAVE THESE INSTRUCTIONS
2-1
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR
SAFETY. The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices, which COULD result in severe personal injury or death.
CAUTION - Hazards or unsafe practices, which could result in minor personal injury or product or
property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper
operating condition. Following is information that signals some potentially dangerous conditions to the
operator or the equipment. Read this information carefully. Know when these conditions can exist.
Locate all safety devices on the machine. Please take the necessary steps to train the machine
operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the
machine. Use approved replacement parts.
2-2
86315410 (BU2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
GROUNDING INSTUCTIONS-120V
Grounding Pin
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
GROUNDING CONNECTION
USING AN ADAPTOR
ELECTRICAL:
Grounded
Outlet
In the USA this machine operates on a one 15
amp nominal 120V, 60 hz, A.C. power circuit. The
amp, hertz, and voltage are listed on the data label
found on each machine. Using voltages above or
below those indicated on the data label will cause
serious damage to the motors.
Metal Screw
FIGURE A
Adaptor
Tab for Grounding
Screw
Grounded
Outlet Box
FIGURE B
Adaptor
FIGURE C
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to
reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment-
grounding conductor and grounding plug. The
plug must be inserted into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.
Note: Adaptors are not allowed in Canada.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in doubt
as to whether the outlet is properly grounded.
Do not modify the plug provided with the
appliance - if it will not fit the outlet, have a
proper outlet installed by a qualified
electrician.
This appliance is for use on a nominal 120-volt
circuit, and has a grounded plug that looks like the
plug in “Fig. A”. A temporary adaptor that looks
like the adaptor in “Fig . C” may be used to
connect this plug to a 2-pole receptacle as shown
in “Fig. B”, if a properly grounded outlet is not
available. The temporary adaptor should be used
only until a properly grounded outlet (Fig. A) can
be installed by a qualified electrician. The green
colored rigid ear, lug, or the like extending from
the adaptor must be connected to a permanent
ground such as a properly grounded outlet box
cover. Whenever the adaptor is used, it must be
held in place by a metal screw.
2-3
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
GROUNDING INSTRUCTIONS-230V
THIS PRODUCT IS FOR COMMERCIAL USE
ONLY.
ELECTRICAL:
The amp, hertz, and voltage are listed on the data
label found on each machine. Using voltages
above or below those indicated on the data label
will cause serious damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be
at least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should
malfunction or break down, grounding provides a
path of least resistance for electric current to
reduce the risk of electric shock. This appliance is
equipped with a cord having an equipment-
grounding conductor and grounding plug. The
plug must be inserted into an appropriate outlet
that is properly installed and grounded in
accordance with all local codes and ordinances.
Improper connection of the equipment-
grounding conductor can result in a risk of
electric shock. Check with a qualified
electrician or service person if you are in doubt
as to whether the outlet is properly grounded.
Do not modify the plug provided with the
appliance - if it will not fit the outlet, have a
proper outlet installed by a qualified
electrician.
86309600 (2000) BURNISHER 10/08/08
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time,
the labels become illegible contact your authorized representative for prompt replacement.
WARNING LABEL
P/N 86219740
PRV NO. 500194
86309600 (2000) BURNISHER 10/08/08
2-5
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
ITEM
DIMENSION/CAPACITY
Construction
Heavy-duty die cast aluminum deck with heavy-duty rubber
bumper, tubular steel self adjusting handle with die cast aluminum
handle housing.
Motor
1.5 hp
Transmission
Pad speed
Direct drive from motor shaft.
2000 rpm
Electrical system:
LB2000I, LB2000IA
LB2000, UB2000F
Cable
230 volts, 50Hz
115 volts, 60Hz
75’ [22.9 m]
Switches
Dual levers with safety lock.
Pad Holder
∅20” [50.8 cm] flexible disc
Wheels
Handle
Four ∅5” [∅12.7 cm], 1.25” [3.2 cm] wide, non-marking tread.
∅1.5” [∅3.8 cm] tubular steel, self adjusting handle consistently
maintains full contact with the floor, and easy to use thumb
activated safety lock.
Dimensions (L x W x H)
Pad size (See note)
32” [81.3 cm] X 23.9” [60.2 cm] X 48.4” [122.9 cm]
20” diameter x 1” thick
NOTE: Always use a pad, which has been designed for electric ultra high speed burnishing of at
least 2000 rpm.
The sound pressure level at the operator’s ear was measured to be 70 dBA. This was a nearfield,
broad-band measurement taken in a typical industrial environment on a tile floor. This appliance
contains no possible source of impact noise. The instantaneous sound pressure level is below 63 Pa.
3-1
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HANDLE
ASSEMBLY
2
3
1
HANDLE
MOUNT BRACKET
DECK
ASSEMBLY
HANDLE INSTALLATION
The machine is shipped with handle unassembled.
Follow these steps for installation:
4. Slide Bolt (item 3) through, washers (item 2),
Handle Mount Brackets and Handle Assembly as
shown. Tighten bolt (item 3) and nut (item 1) until
the handle cannot twist in the mount bracket (45-
50 foot pounds).
1. Remove handle and deck assembly from
carton.
5. Check handle for movement up and down.
6. Plug cord into handle cord receptacle.
2. Remove bolt (item 3), washers (item 2), and
nut (item 1) from deck assembly.
3. Install Handle Assembly as shown.
3-2
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
6. To stop the machine, release the switch
levers.
CONTROLS
1. Safety Lock – Prevents unintended operation
7. Do not let machine rest on pad. When
finished with the machine, return handle to the
storage position.
of the machine.
2. Switch Levers – Turns machine on/off.
NOTE: The machine is equipped with a circuit
breaker to protect the motor in the event an
overload condition occurs. The circuit breaker is
located on the handle. Push the reset button to
restart the machine. If the breaker trips again,
correct the cause of overloading before
proceeding.
1
2
2
DAILY MAINTENANCE
1. Inspect power cord for wear. To prevent
electrical shock replace cords with frayed or
cracked insulation immediately.
2. Place machine in the storage position.
3. Check pad condition. Change if soiled or torn.
PAD INSTALLATION
1. Lay machine back, exposing the under
side.
OPERATION
2. Remove center lock by turning counter-
clockwise.
For indoor use only.
3. Ensure pad is centered on pad driver. Pull
pad to edge of pad driver in several
directions to check for proper
engagement.
When using the pad, always keep the machine
moving when in contact with the floor.
High starting torque. Hold machine firmly with
both hands.
4. Replace center lock by turning clockwise
firmly compressing the center of the pad.
1. Ensure that the pad driver is in good shape.
Install or change pad if necessary.
2. Plug the machine into a wall outlet as
described in the grounding instructions.
HANDLE
RELEASE LATCH
3. Release latch, lower the handle and move into
position.
4. Push the safety lock forward, unlocking the
switch levers.
5. With the safety lock forward, squeeze one or
both of the switch levers, turning the machine
on. (These levers can be operated
independently of each other). The safety lock
will not re-engage until both levers are
released.
3-3
86309600 (2000) BURNISHER 01/29/09
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
MACHINE TROUBLESHOOTING
PROBLEM
CAUSE
Tripped circuit breaker
SOLUTION
Reset
Circuit breaker tripped in Check and reset
building.
Fuse in motor is blown
Replace
CAUTION: To reduce the risk of
electrical shock, unplug the
machine before opening fuse
holder.
Fuse will only open under extreme
conditions.
Machine will not run
Investigate cause before replacing.
Test switch for continuity and
replace if necessary.
Replace
Power switch failure
Faulty power cord
Equipment not grounded Follow grounding instructions
exactly.
Receptacle not grounded Have an electrician inspect
building’s wiring.
Electrical shock
Internal wiring problem
Ensure that the machine wiring
matches the appropriate wiring
diagram. Replace any wires or
components, which are short-
circuiting.
Mechanical problem
Higher amp draws indicate a
mechanical problem; find the
problem before using the machine.
Test circuit for continuity. Replace
circuit breaker if necessary.
Re-center pad.
Excessive vibration
Faulty circuit breaker
Pad not centered
Damaged or unevenly
worn pad.
Damaged pad driver.
Replace pad. Do not rest machine
on pad when not in use.
Replace.
86309600 (2000) BURNISHER 10/08/08
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
SERVICE SCHEDULE
MAINTENANCE
Check pad wear to prevent buildup of chemicals
Check pad driver system for damage
DAILY MONTHLY
*
*
*
*
*
*
*
Check handles, switches, and knobs for damage
Store with pad off the floor
Check all bearings for noise
Check skirt/bumpers for damage and replace as necessary
Check overall performance of machine
4-2
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES:
4-3
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK
1
2
3
5
6A-B
4
7
8
9
11
10
16
12
13
14
15
5-1
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
BUMPER, RUBBER
COVER, FILTER BAG
BAG, DUST (PACKAGE OF 10 BAGS)
RETAINER, CORD
NOTES:
1
2
3
4
5
86216280
86217520
86001390
86223430
86276810
140449
27918
140441
67463
70738
4
1
1
1
2
SCR, M5 X .8MM X 10 MM PPHMS BLK
LB2000,
6A
86217640 29244BLU
1
DECK, 20 IN BURNISHER, BLUE
LB2000I,
LB2000IA
6B
7
8
86289010 29244GRY
1
1
2
2
2
2
2
4
2
2
DECK, 20 IN BURNISHER, GRY
BUMPER, EXTRUSION
WASHER, M6 FLAT BLK
SCR, M6 X 25 HHMS
NUT, M6 X 1 HEX NYLOCK PLTD
CAP EXTRUSION
UB2000UF
86216270
86137340
86276570
86271550
86216600
86215020
86225720
86137280
86136640
140423
87211
70691
57220
27871
05156
87203
87054
70262
9
10
11
12
13
14
15
AXLE, FRONT
WASHER, 14MM ID X 36 MM OD
WASHER, M8 FLAT DIN125A PLT
SCR, M8-1.25 X 20 HHMS PLTD
SCR, SET M8 X 1.25 X 8MM CUP
POINT
16
86288740
70709
2
5-2
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
1
4
3
2
15
14 A-B
5
6
7
13 A-C
12
11
10
9
8
5-3
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
1
2
3
86136780
86137290
86224750
70801
87057
73993
2
2
1
SCR, M 3.5 X 40 PHTF TYPE B
WASHER, M4 SHAKEPROOF
SPRING, COMP, .48OD X .91L
SWITCH, 25A SPST 125-250V
SNAP
SCR, M4.8 X 10 HHTF TYPE B
WASHER, M5 SHAKEPROOF
PLTD
4
5
6
86007110
86288450
86137330
72123
70689
87208
2
1
1
7
8
9
10
11
12
86198450
86227300
86224930
86215430
86216940
86002010
20005
730021
730012
14407
23209
14942
1
1
1
1
1
1
CLAMP, 5/16 NYLON
SPACER, POLISHER HANDLE
STRAIN RELIEF, 14/3 STRAIGHT
BOOT, CORD END
CORD SET, 14/3 X 38 IN,SJT, BLK
BOOT, 3/8 CIRCUIT BREAKER
LB2000,
UB2000F
13A
86234140
23154
1
CORD SET, 14/3 ST C 75’ YLW
CORD SET, EURO 1.5MM X 75
BLK
CORD SET, SAA/3 1.5MM X 75
13B
13C
14A
86216950
86216970
86312460
23212
23217
-
1
1
1
LB2000I
LB2000IA
LB2000,
UB2000F
LB2000I,
LB2000IA
BREAKER, 14A, VDE CIRCUIT
14B
15
86291460
86215140
-
1
1
BREAKER, 11A, VDE CIRCUIT
BARRIER SHEET
140674
5-4
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE-LOWER
16
15
17
14
19
17
18
10
24
7
8
23
6
9
1
2
5
11
3
4
13
12
22
21
20
25
8
5-5
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE-LOWER
SERIAL
NOTES:
NO.
PART
NO.
PRV
NO.
REF
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
86276810
86198450
86223490
86222570
70738
20005
67468
66340
1
1
2
1
1
2
2
6
1
1
1
2
1
1
SCR, M5 X .8MM X 10 MM PPHMS BLK
CLAMP, 5/16 NYLON
RING, 10MM EXT SNAP, DIN 471
PIN, DOWEL 10MM DIA X 124 MM LG
BRACKET, HANDLE LINK
RING, 13MM EXTERNAL SNAP
WASHER, 14MM ID X 36MM OD X 2MM
WASHER, 14MM ID X 36 MM OD
SPACER, LINKAGE
86215480 140421
86223500
86288760
86225720
86224310 730052
86288770 500542
86221720
86226020
86224590 730055
86215390 140420
67469
87234
87203
LABEL, HANDLE RELEASE
LATCH, HANDLE
51358
89206
WHEEL, 5D X 1.25 X 13MM ID GRY
SPRING, 180 DEGREE TORSION
BLOCK, SPRING COMPRESSION
SPRING, COMP 1.140 OD X 8.40 L X
.150 W
15
86224580 730054
1
16
17
18
19
20
21
22
23
24
25
86005770
86279510
86274000
57119
87171
70069
1
2
1
2
2
2
1
4
1
2
NUT, 3/8-16 HEX NYLOCK
WASHER, 3/8 FLAT
SCR, 3/8-16 X 3 HHCS GR5
BRACKET, HANDLE MOUNT
SCR, M8-1.25 X 20 HHMS PLTD
WASHER, M8 FLAT DIN125A PLT
AXLE, REAR
SCR, M6 X 25 SHCS PLTD
STRIKER, LATCH
SET SCR, 8MMX1.25MM CUP PT
86215470 140419
86136640
86137280
86215030
86223710
86225010 730053
86288740 70709
70262
87054
05157
70733
NOTE: Grease contact surfaces of Items 14 and 15 as necessary when servicing.
5-6
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE-UPPER
13
4
6
12
5
1
3
7
2
9
10
8
10
8
11
5-7
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
HANDLE-UPPER
SERIAL
NOTES:
NO.
PRV
NO.
REF PART NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
86136670
86136680
86224740
86225370
86004070
86005160
86136350
86279080
70686
70687
73990
78437
36196
51327
57274
87058
2
2
2
1
2
2
4
3
SCR, M6 X 45 SHCS BLK
SCR, M6 X 50 SHCS BLK
SPRING, EXT, .50D X 3.5L
TUBE, GRIP HANDLE
GRIP, POLISHER HANDLE
LEVER, SWITCH
NUT, M6 HEX FINISH
WASHER, M4 FLAT DIN125A PLT
HOUSING, POLISHER HANDLE RR,
CD
9
86311810
-
1
10
11
86288450
86225390
70689
78473
3
1
SCR, M4.8 X 10 HHTF TYPE B
TUBE, HANDLE
HOUSING, POLISHER HANDLE FRT,
CB
LOCK, SAFETY HANDLE
12
13
86311820
86005150
-
1
1
51326
86309600 (2000) BURNISHER 10/08/08
5-8
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR
3
2
1 A-B
6
4
5
5-9
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTOR
PART
NO.
PRV
NO.
SERIAL NO.
FROM
REF
QTY
DESCRIPTION
NOTES:
MOTOR, 115V 1.5HP
20000RPM
MOTOR, 230V 1.5HP
20000RPM
1A 86312260
1B 86312250
-
-
1
1
LB2000, UB20000F
LB2000I, LB2000IA
2
3
86217490
86223690
27884
70702
1
3
COVER, MOTOR 1.25HP
SCR, M5 X .8 X15MM BLK
WASHER, 3/8 SPLIT LOCK
PLTD
4
86010790
87163
4
SCR, 3/8-16 X 3/4 HHCS GR5
PLT
KEY, 3/16 SQ X .85 LG CRS
5
6
86006920
86219610
70507
48082
4
1
MOTOR COMPONENTS (NOT SHOWN)
PRV
NO.
SERIAL NO.
FROM
PART NO.
QTY
DESCRIPTION
NOTES:
86223460
86001720
86003660
86003670
67499
140785
34378
34379
1
1
1
1
RECTIFIER, 50A 1000V BRIDGE
BRUSH SET (PKG OF 4)
FUSE
FUSE HOLDER
SEALED BALL BRNG, 25 MM X
52MM
BOTTOM MOTOR
BEARING
TOP MOTOR
BEARING
86223980
86001020
09134
09135
1
1
SEALED BALL BRNG, MOTOR
5-10
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
PAD/DRIVER
8
1
2
9
3
4
5
6
7
5-11
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
PAD/DRIVER
PART
NO.
PRV
NO.
SERIAL NO.
FROM
REF
QTY
DESCRIPTION
NOTES:
1
2
86010720
86006920
87086
70507
4
4
WASHER, M10 X 30 PLTD
SCR, 3/8-16 X 3/4 HHCS PLT
PAD DRIVER, 20 INCH
BURNISHER
INCLUDES ITEMS
6 & 7
3
86222470
64108
1
4
5
6
7
86279210
86274590
86276740
86246740
87102
70244
70720
51353
1
1
3
1
WASHER, 5/16 ID X 1-1/4 OD
SCR, 5/16-24 X 1/2 HHMS SS
SCR, #10 X 3/8 PPHST TYPE B
LOCK, PAD DRIVER BLUE
SHROUD, ASM. 20 IN
8
9
86223660 730065
86216230 730074
1
1
INCLUDES ITEM 9
BURNISHER
BRUSH, STRIP (PACKAGE OF 6)
86309600 (2000) BURNISHER 10/08/08
5-12
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING-120V
CORD SET
WHT
BLK
GRN
-CB1
120V AC 15A
1
-SWITCH
-SWITCH
WHT
WHT
BLK
BLK
GRN
M
-MOTOR
GRN
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
DESCRIPTION
NOTES:
WIRE, 125MM, BLK/14,
76029X76029
1
86311830
-
1
5-13
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING-230V
CORD SET
WHT
GRN
BLK
-CB1
120V AC 15A
1
EMC FILTER
-SWITCH
-SWITCH
EMC FILTER2
WHT
WHT
BLK
BLK
GRN
M
-MOTOR
GRN
SERIAL NO.
FROM
REF PART NO. PRV NO. QTY
86311830
DESCRIPTION
NOTES:
WIRE, 125MM, BLK/14,
76029X76029
1
-
1
5-14
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
SERIAL NO.
FROM
PART NO.
PRV NO.
DESCRIPTION
NOTES:
86224740
86224750
86007110
86312460
86291460
86223460
86003660
86003670
86001020
86246740
86001390
86215390
86216230
86001820
86001720
73990
73993
72123
-
SPRING, EXT .5OD X 3.5L
SPRING, COMP .48OD X .91L
SWITCH, 25A SPST 125-250V SNAP
BREAKER, 14A, VDE CIRCUIT
BREAKER, 11A, VDE CIRCUIT
RECTIFIER, 50A 1000V BRIDGE
FUSE
120V
230V
-
67499
34378
34379
09135
51353
140441
140420
730074
14404
140785
FUSE HOLDER
SEALED BALL BRNG, MOTOR
LOCK, PAD DRIVER BLUE
BAG, DUST (PACKAGE OF 10 BAGS)
BLOCK, SPRING COMPRESSION
BRUSH, STRIP (PACKAGE OF 6)
BRUSH SET
120V
230V
BRUSH SET (SET OF 4)
5-15
86309600 (2000) BURNISHER 10/08/08
Download from Www.Somanuals.com. All Manuals Search And Download.
86309600 (2000) BURNISHER
Download from Www.Somanuals.com. All Manuals Search And Download.
|