™
SoundPlus
Infrared Listening System
Installation Guide & User Manual
Model WIR TX90, Two Channel System
Model WIR SYS 90 ADV, Two Channel System
Model WIR SYS 91V, Two Channel System
Optional Receiver Models WIR RX22-4, WIR RX15-2, WIR RX18
Optional Charger Models CHG 518, CHG 3512
WIR SYS 90ADV
WIR SYS 91V
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
System Overview
The WIR TX90 two channel infrared transmitter combines infrared modulator and emitter technology into a single
mountable enclosure - reducing operating cost and eliminating precious rack space.
The WIR TX90 features an easy to use configuration preset for Music, Voice, or Hearing Assistance Applications. It
operates on dual 2.3/2.8 or 3.3/3.8 MHz selectable frequencies - ideal for high quality audio programs such as music,
theater and audio description. The WIR TX90 will accept any line level, balanced or unbalanced audio inputs, and
includes adjustable tone and volume control. Infrared receivers detect the transmission and convert the light signals back
into audio signals. The 2.3-3.8 MHz operating frequencies minimize high efficiency lighting interference. No FCC license
or radio approval is required with this equipment. It can be used anywhere in the world.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference at
his own expense.
NOTICE: A plasma monitor can degrade the audio quality of the SoundPlus™ Infrared Listening System.
Figure 1: Typical Two-Channel configuration for the WIR TX90
MOUNTING
BRACKET
RX22-4 RECEIVERS
(WIRELESS)
AUDIO
INPUTS
BASEBAND
OUTPUTS
POWER
SUPPLY
TO ADDITIONAL
EMITTERS
(IF NECESSARY)
CH B
AUDIO IN
CH A
AUDIO IN
SOUND SYSTEM
A236
MAN 119H
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundPlus™ Infrared Listening System
Determine Coverage Area
Determine the coverage area needed for the seating area. When using the WIR TX90 transmitter with the RX22-4 receiver, in
single channel mode, the WIR TX90 can achieve a coverage area of 28,000 ft2 (2,600 m2). In four channel mode, the WIR
TX90 divides its power among the four signals to achieve a coverage area of 11,000 ft2 (1,022 m2).
NOTE: The coverage area will vary depending on the sensitivity of the infrared receiver being used. The following
diagram illustrates coverage area when using a RX22-4, RX15-2, or RX18 receiver with a single WIR TX90
transmitter in single channel mode.
Figure 2: Maximum range when using the RX22-4, RX15-2, or RX18 Receiver
FEET
90
RECEIVER COVERAGE AREA WITH
TX9 OR TX90 TRANSMITTER IN
80
SINGLE CHANNEL MODE
70
60
RX22-4 RECEIVER
RX15-2 RECEIVER
RX18 RECEIVER
50
40
30
20
10
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
A136
FEET
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160
These patterns are the direct radiation pattern. The infrared radiation does not drop to zero outside the illustrated patterns; it
decreases. It still may be useable at a greater distance, depending on the receiver sensitivity and the reflective characteristics of
the room.
Reflections of the infrared light from walls, ceilings, and floors may change these patterns.
Important: Remember to point the transmitter towards the listening audience!
Remember: opaque objects block infrared light. Thus, the transmitter cannot be concealed behind opaque walls, curtains, etc.
4
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
Figure 3: 3 Dimension Foot Pattern
Figure 4: NOTE: When pointing the emitter, be
sure to keep the long dimension horizontal.
CORRECT
A237
Figure 5: Overlapping Illumination patterns to cover Larger Listening Areas
INCORRECT
A230
WIRTX90
WIRTX9
WIRTX9
WIRTX9
A238
Figure 6: Overlapping Illumination patterns to cover Larger Listening Areas
COVERAGE AREA
WITH SINGLETRANSMITTER
COVERAGE AREA
WITH SECOND EMITTER
ADDED TO SAME
EMISSION POINT
(50% INCREASE)
WIRTX90
WIRTX9
A239
MAN 119H
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundPlus™ Infrared Listening System
Figure 7: WIR TX90 Rear View
POWER CONNECTION
PLUG IN POWER SUPPLY
120 VAC (US): TFP 010
230 VAC (CE): TFP 027
WALL/CEILING
BASEBAND OUT
BNC CONNECTOR, 50 Ω
50 KHZ-8 MHZ BASEBAND
MOUNTING BRACKET (BKT 024)
SET OF THREADED HOLES FOR USE
WITH MOUNTING BRACKET
A229
Connect Power
WARNING: POWERLINE VOLTAGE MUST NOT FALL BELOW 90V, 0R SYSTEM PERFORMANCE WILL BE
GREATLY REDUCED!
Power Connection for U.S. Application
Connect the TFP 010 power supply to the 3-pin Molex™ connector located on the rear of the TX90 (see Figure 7).
For Applications Outside the U.S. Requiring 240 VAC Mains Supply:
Use the transformer power supply, model TFP 027. Make sure TFP 027 power input switch (located on bottom of power supply) is
set to the “230” position. Secondary specifications: 24 VAC, 35 VA, 50/60 Hz.
Plug the power supply into the AC outlet.
TFP 027-01: 230VAC, Euro Mains Plug
TFP 027-02: 230VAC, UK Mains Plug
NOTE: The WIR TX90 transmits when a baseband signal is present, and will shut off immediately when no baseband signal is
present. This auto shut-off feature preserves the life of the infrared LEDs and reduces power consumption.
This system is designed for class 2, low-voltage wiring. Always follow local electrical codes when doing low voltage wiring.
6
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
Connect Audio Source
Determine the length of the audio cable needed to connect to the sound system to the WIR TX90 transmitter. Install the supplied
Phoenix connector on the end of the audio cable to be connected to the transmitter. See the back of the WIR TX90 for wiring
instructions.
Figure 8: Audio Source Connections
BALANCED
UNBALANCED
SIGNAL
SIGNAL
SIGNAL
+
+
–
G
–
G
SHIELD
SHIELD
JUMPER
LINE LEVEL BALANCED OR UNBALANCED (5V P/P MAXIMUM AUDIO)
A232
The WIR TX90 will accept line level, balanced or unbalanced audio inputs. If you wish to operate in single channel mode, plug the
audio cable with the installed Phoenix connector in “Channel A” OR the “Channel B” connector. If you choose to operate in two
channel mode, plug the audio cables with Phoenix connectors in both “Channel A” AND “Channel B” connector.
NOTE: By default, the WIR TX90 is set to operate in two-channel mode. To turn Channel A or Channel B on/off, refer to the
instructions Selecting a Channel, below.
POWER ON INDICATOR
Figure 9
FREQUENCY
SELECTION CONTROL
(2.3/2.8 OR 3.3/3.8)
CHANNEL
ON/OFF
CONTROL
CHANNEL
ON/OFF
CONTROL
AUDIO
ADJUSTMENT
CONTROL
AUDIO
ADJUSTMENT
CONTROL
(VOLUME/TONE)
A231
Selecting a Carrier Frequency
The WIR TX90 offers two sets of carrier frequencies for Channel A and Channel B:
2.3 and 2.8MHz or 3.3 and 3.8MHz.
The WIR TX90 is preset to 2.3 and 2.8 MHz, which are the most commonly used. Move the slide switch to select a pair of
operating frequencies.
Selecting a Channel
To activate a channel, press the “CHANNEL” button until the channel “ON” indicator lights. For example, to operate only channel
A, press the “CHANNEL” button until only the channel A “ON” indicator lights. To operate both channel A and B, press the
“CHANNEL” button until both “ON” indicators light.
Note: If you’re only using one channel, make sure the other channel is turned off to maximize system coverage.
MAN 119H
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundPlus™ Infrared Listening System
Select the Audio Processing Application Preset
The WIR TX90 offers three preset audio processing options for the most common applications: Music, Voice, and Hearing
Assist. Use the “Music” setting when maximum dynamic range and audio quality are preferred. Use the “Voice” setting for
simultaneous interpretation, audio description, or other applications with users that have primarily normal hearing. Use the
“Assist” setting for hearing assistance applications to meet the reduced dynamic range needs of hearing impaired listeners.
You may select the same audio pre-set for both Channel A and Channel B, or you may select them independently.
To select the audio processing preset, you must first activate the channel you want to adjust. Press the “channel” button to
activate the channel(s) you want to choose an audio processing preset for, then press the “Presets” button to choose the
preset. The Music, Voice, or Assist indicator will light to show your selection. After 10 seconds, the setting will be stored.
Adjusting Audio Input Level
The TX90 is designed to accept a line-level audio input signal. The “Level” indicator light for each channel is used to help
adjust the audio input level. When the indicator does not light, the input signal level is too low. When the indicator is flashing,
the signal level is optimal. When the indicator is steadily lit, but does not flash, the input level is too high and can cause
distortion. You can adjust the input level of both channels simultaneously, or independently.
Make sure the input audio signal is connected to the WIR TX90. To adjust the audio input level, first activate the channel(s)
you want to adjust by pressing the “CHANNEL” button, then press the “VOLUME” button. The Volume indicator will light.
Now, turn the “ADJUST” knob clockwise to increase the input signal or counter-clockwise to decrease the input signal until
the channel “Level” indicator is flashing. After 10 seconds, the setting will be stored.
IMPORTANT
Audio level NORMAL (optimal): the audio indicator level will flash at a 1 second rate.
Audio level too HIGH: the audio indicator level will stay on or flash erratically.
Audio level too LOW: the audio indicator level will be off.
Adjusting Tone
The WIR TX90 has a tone adjustment to suit user preference and to compensate for the different frequency responses of
various infrared receiver models. First, make sure the audio source is active. Use a receiver from the system to listen to the
signal as you adjust the tone control.
To adjust the tone, first activate the channel(s) you want to adjust by pressing the “CHANNEL” button, then press the
“TONE” button. The tone indicator will light. Now turn the “ADJUST” knob clockwise to emphasize high frequencies (best
for hearing assistance use). When you have reached the maximum adjustment, there will be no further change in tone. Turn
the “ADJUST” knob counter-clockwise to decrease the high frequency emphasis. When you have reached the minimum
adjustment, there will be no further change in tone. After 10 seconds, the setting will be stored.
8
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
Using the Optional WIR TX9 Slave Emitter for Additional Coverage
For larger facilities, additional emitter panels can be used to increase the overall coverage area. In these cases, we recommend
using the WIR TX9 slave emitter in tandem with the WIR TX90. The WIR TX90 can drive multiple WIR TX9 emitters at one time.
Each TX9 emitter will require its own power supply.
Figure 10: Connecting a WIR TX9 Emitter to a WIR TX90 Transmitter
WIR TX9 EMITTER (REAR)
WIR TX90 TRANSMITTER (REAR)
Multi-Channel Infrared Transmitter
RoHS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
Class
LED Product
1
Mounting
Bracket
Note: It is normal for this unit to feel warm while it is in operation.
Power Supply Wiring:
Use NEC, Class
2
Wiring, 18 ga. minimum,
200 ft. (70m) maximum length (18 ga.)
Baseband Signal Wiring:
Use 50 Ohm Coaxial Cable (RG58)
Baseband Signal Wiring:
Use RG58 Coax,1000 ft. (350m) max. length
Williams Sound, Minneapolis, Minnesota, USA
Patent Pending
Made in U.S.A.
Baseband
(Modulation)
NC 24 VAC
Power In:
Out
Out
In
50 Ohms
24VAC
~
Plug
50-60Hz
35VA
Power On
Baseband On
BASEBAND
INPUT
BASEBAND
OUTPUT
A234
TO TX9 EMITTER
To add a second WIR TX9 emitter panel to the WIR TX90 transmitter, repeat the process above (the WIR TX90 transmitter
has two baseband output jacks).
Note: The WIR TX9 emitter panels can be “chained” together if needed for unlimited coverage area. Each
WIR TX9 emitter will require its own power supply. See Figure 11 below.
Figure 11: Chaining multiple WIR TX9 Emitters Together
WIR TX9 EMITTER #2 (REAR)
WIR TX9 EMITTER #2 (REAR)
WIR TX90 TRANSMITTER (REAR)
Multi-Channel Infrared Transmitter
Multi-Channel Infrared Transmitter
RoHS
RoHS
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
Class
LED Product
1
Class
LED Product
1
Mounting
Bracket
Mounting
Bracket
Note: It is normal for this unit to feel warm while it is in operation.
Power Supply Wiring:
Note: It is normal for this unit to feel warm while it is in operation.
Power Supply Wiring:
Use NEC, Class
2
Wiring, 18 ga. minimum,
Use NEC, Class
2
Wiring, 18 ga. minimum,
200 ft. (70m) maximum length (18 ga.)
200 ft. (70m) maximum length (18 ga.)
Baseband Signal Wiring:
Use 50 Ohm Coaxial Cable (RG58)
Baseband Signal Wiring:
Use 50 Ohm Coaxial Cable (RG58)
Baseband Signal Wiring:
Use RG58 Coax,1000 ft. (350m) max. length
Baseband Signal Wiring:
Use RG58 Coax,1000 ft. (350m) max. length
Williams Sound, Minneapolis, Minnesota, USA
Patent Pending
Williams Sound, Minneapolis, Minnesota, USA
Patent Pending
Made in U.S.A.
Made in U.S.A.
Baseband
Baseband
(Modulation)
(Modulation)
NC 24 VAC
Power In:
Out
Out
In
NC 24 VAC
Power In:
Out
Out
In
50 Ohms
50 Ohms
24VAC
~
24VAC
~
Plug
Plug
50-60Hz
35VA
50-60Hz
35VA
Power On
Baseband On
Power On
Baseband On
BASEBAND
OUTPUT
BASEBAND
INPUT
BASEBAND
OUTPUT
BASEBAND
INPUT
BASEBAND
OUTPUT
BASEBAND
INPUT
TO ADDITIONAL
EMITTERS
TO SECOND TX9 EMITTER
TO TX9 EMITTER
TO ADDITIONAL
EMITTERS
A233
MAN 119H
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundPlus™ Infrared Listening System
Receiver Safety Information
HEARING SAFETY
CAUTION!
Williams Sound receivers are designed to amplify sounds to a high volume level which could potentially cause hearing damage if
used improperly. To protect your hearing and the hearing of others:
1. Make sure the volume is turned down before putting on the earphone or headphone before adjusting the volume to a comfortable
level.
2. Set the volume level at the minimum setting that you need to hear.
3. If you experience feedback (a squealing or howling sound), reduce the volume setting and move the microphone away from the
earphone or headphone.
4. Do not allow children or other unauthorized persons to have access to the receiver.
BATTERY SAFETY AND DISPOSAL
CAUTION!
Williams Sound receivers are supplied with disposable Alkaline batteries. Do not attempt to recharge disposable batteries, which
may explode, release dangerous chemicals, cause burns, or other serious harm to the user or product.
PACEMAKER SAFETY
CAUTION!
1. Before using Williams Sound receivers with a pacemaker or other medical device, consult your physician or the manufacturer of
your pacemaker or other medical device.
2. If you have a pacemaker or other medical device, make sure that you are using the Williams Sound receiver in accordance with
safety guidelines established by your physician or the pacemaker manufacturer.
Recycling Instructions
Help Williams Sound protect the environment! Please take the time to dispose of your equipment properly.
Product Recycling Instructions:
Please do NOT dispose of your Williams Sound equipment in the household trash. Please take the equipment to an
electronics recycling center; OR, return the product to the factory for proper disposal.
Battery Recycling Instructions:
Please do NOT dispose of used batteries in the household trash. Please take the batteries to a retail or community
collection point for recycling.
10
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
Optional Infrared Receivers
Figure 12: Four Channel Receiver, Model WIR RX22-4
Channel
Frequency
2.3 MHz
2.8 MHz
3.3 MHz
3.8 MHz
1
2
3
4
CHANNEL
SELECTOR
EARPHONE
JACK
OFF
ON/OFF
VOLUME SWITCH
"ON"
INDICATOR
A162
Figure 13: WIR RX15-2 Headset Receiver
LEFT
INFRARED
SENSOR
RIGHT
POWER/CHANNEL
SWITCH
POWER/
CHANNEL
INDICATOR
BATTERY
COVER
VOLUME
KNOB
MONITOR/MUTE
BUTTON
AUDIO INPUT JACK
A169
Figure 14: WIR RX18 Under-the-chin Receiver
VOLUME
CONTROL
BATTERY
(BAT AP07D)
A235
MAN 119H
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundPlus™ Infrared Listening System
Optional Chargers
Figure 15: Multiple Battery Charger, Model CHG 518
WIR RX18 RECEIVER
CHG 518
FRONT-TOP VIEW
CHG 518
REAR VIEW
TFP 043 AC
POWER CONNECTION
CHARGING
INDICATORS
CHG 518 Back
A223
Figure 16: Multiple Battery Charger, Model CHG 3512
CHG 3512
REAR VIEW
RECEIVER OR
TRANSMITTER
DC POWER
CHARGING
INDICATOR
A124
12
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
Trouble Shooting
The WIR TX90 “Power On” indicator is not lit.
• Make sure the transformer is plugged into the transmitter and any remote power switch is on.
• Make sure the electrical outlet is on.
• Make sure the 24 VAC power supply is working.
The WIR TX90’s channel A or B “On” indicator is not lit.
• Make sure the desired audio channel has been activated. See Selecting a Channel on page 7.
• Make sure the WIR TX90 is plugged in.
• Make sure the audio input is connected properly. See page 6 or instructions on the back of the WIR TX90.
• Make sure an active audio signal is being sent to the WIR TX90 transmitter.
No sound through receivers.
• Check to make sure the receiver is operating on the same frequency as the transmitter.
• If some of the receivers work but others don’t, check for bad batteries or earphones on the receivers that aren’t working.
• If none of the receivers work, check to see if the power and audio input cable are connected to the transmitter and that the
WIR TX90 “Power On” and Channel A or B “On” indicator is illuminated.
• Check to see if the transmitter is connected properly to the sound system. The audio level indicators should flash on channels
that are selected.
• Make sure the “eye” is not covered up on the receiver. There must be clear line of sight between the receiver eye and the
transmitter panel.
Sound through the receivers is weak and noisy.
• Listen to the audio signal through the headphone jack on the WIR TX90 transmitter (Figure 10). If the signal is weak and noisy
here, try increasing the audio input level (see Adjust Audio Input Level, page 8), or increase the input signal level from the
sound system by turning up the mixer control. If the signal sounds okay, you may need to reposition the transmitter panel or
add additional IR emitters to the TX90 system.
Buzzing or humming noise in sound system.
• Check for ground loops or noise on the input signal. Call your Authorized Williams Sound dealer or representative.
NOTE: Make sure the power line voltage does not fall below 90V, or system performance will be greatly reduced!
MAN 119H
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SoundPlus™ Infrared Listening System
Limited Warranty
Williams Sound products are engineered, designed, and manufactured under carefully controlled conditions to provide
you with many years of reliable service. Williams Sound warrants the Sound Plus™ Infrared Listening System against
defects in materials and workmanship for FIVE (5) years. During the first five years from the purchase date, we will
promptly repair or replace the Sound Plus™ Infrared Listening System.
Microphones, earphones, headphones, batteries, chargers, cables, carry cases, and all other accessory products carry a
90-day warranty.
WILLIAMS SOUND HAS NO CONTROL OVER THE CONDITIONS UNDER WHICH THIS PRODUCT IS USED. WILLIAMS
SOUND, THEREFORE, DISCLAIMS ALL WARRANTIES NOT SET FORTH ABOVE, BOTH EXPRESS AND IMPLIED,
WITH RESPECT TO THE SOUND PLUS™ INFRARED LISTENING SYSTEM, INCLUDING BUT NOT LIMITED TO, ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. WILLIAMS SOUND SHALL
NOT BE LIABLE TO ANY PERSON OR ENTITY FOR ANY MEDICAL EXPENSES OR ANY DIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY ANY USE, DEFECT, FAILURE OR MALFUNCTIONING OF THE PRODUCT,
WHETHER A CLAIM FOR SUCH DAMAGES IS BASED UPON WARRANTY, CONTRACT, TORT OR OTHERWISE,
THE SOLE REMEDY FOR ANY DEFECT, FAILURE OR MALFUNCTION OF THE PRODUCTS REPLACEMENT OF
THE PRODUCT. NO PERSON HAS ANY AUTHORITY TO BIND WILLIAMS SOUND TO ANY REPRESENTATION OR
WARRANTY WITH RESPECT TO THE SOUND PLUS™ INFRARED LISTENING SYSTEM. UNAUTHORIZED REPAIRS
OR MODIFICATIONS WILL VOID THE WARRANTY.
The exclusions and limitations set out above are not intended to, and should not be construed so as to contravene
mandatory provisions of applicable law. If any part or term of this Disclaimer of Warranty is held to be illegal,
unenforceable, or in conflict with applicable law by a court of competent jurisdiction, the validity of the remaining portions
of this Disclaimer of Warranty shall not be affected, and all rights and obligations shall be construed and enforced as if
this Limited Warranty did not contain the particular part or term held to be invalid.
If you experience difficulty with your system, call Toll-Free for customer Assistance:
1-800-843-3544 (U.S.A.) or +1 952 943 2252 (Outside the U.S.A.)
If it is necessary to return the system for service, your Customer Service Representative will give you a Return
Authorization Number (RA) and shipping instruction.
Pack the system carefully and send it to:
Williams Sound
Attn: Repair Dept.
10300 Valley View Rd
Eden Prairie, MN 55344 USA
Your warranty becomes effective the date you purchase your system. Your returned warranty card is our way of knowing
when your warranty begins. It also gives us important information about your system including the serial number. This
information will help us serve you better in the future. Please take a moment to complete and mail the attached card.
Thank you.
14
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
™
SoundPlus Infrared Listening System Specifications
Infrared Transmitter, Model WIR TX90
Dimensions, Weight: 11.25” W x 6.25” H x 2.125” D (28.6 cm x 15.9 cm x 5.4 cm), 1.8 lbs (0.8 kg)
Color: Black with white legends, black acrylic lens (available in white)
Power Supply: Wall Transformer, 24 VAC, 50-60 Hz, 35 VA, 3-pin MOLEX Connector
North America: TFP 010, UL/CSA
Europe: TFP 027-01, 2-pin Schuko plug, CE
UK: TFP 027-02, 3-pin UK plug, CE
Power Cable: NEC Class 2 wiring, two-conductor, 18 ga., 200’ (61m) max. length
Modulation: FM Wideband, +50kHz deviation max., 50uS pre-emphasis
Carrier Frequency: Channel A: Selectable, 2.3/2.8 MHz,
Channel B: Selectable, 3.3/3.8 MHz
Emitter IR Power: 3.5 watts
Coverage Area: 28,000 sq. ft. (2600 sq. m) in single channel mode when using the RX22-4 Receiver
18,000 sq. ft (1700 sq. m) in two channel mode when using the RX22-4 Receiver
11,000 sq. ft (1000 sq. m) in four channel mode when using the RX22-4 Receiver
3,500 sq. ft (325 sq. m) in single channel mode when using the RX15-2 Receiver
3,063 sq. ft (285 sq. m) in single channel mode when using the RX18 Receiver
Signal-to-Noise Ratio: >75 dB, +3dB
Frequency Response: 80 to 15,000 Hz, electrical response
Total Harmonic Distortion: Less than .2%, electrical response at 1kHz
Compression: Music preset 1:1, Voice preset 1.5:1, Hearing Assist preset 2:1
Auto Carrier Shut-Off: 20 minute timer shuts off carrier when no audio is present
Power Indicator: Red LED
Audio Volume Level Controls: CHA and CHB Input Level, press to select, 28 dB adjustable range
Audio Indicators: CHA and CHB Audio Level, yellow LED, flash
Carrier LEDs: 2 green LED carrier “on” indicators
Phones Output: 3.5mm TRS headphone jack. CH A tip, CH B ring on jack, 32 ohm headphone (min)
Application Preset: Music, Voice, Hearing Assist. Frequency response; Music: Flat; Voice: Mid-range boost; Hearing Assist: High frequency
boost
Tone Control: Press to select, 21 dB adjustable range (1 kHz between low boost/hi-cut and low cut/hi boost).
Power Input: 3-Pin Molex, 24 VAC, 50-60 Hz, 35 VA
Audio Input Connector: CHA and CHB, 3 wire Phoenix
Input Level: Balanced or unbalanced, 316 mVRMS (-10dBV) nominal, 5.7k input impedance; max input (over volume range) -21 to +7
dBV.
Baseband Output: BNC, 50 Ω, for use with TX9 only
Baseband Cable: RG 58 Coax, BNC connectors, maximum 1000’ (300m) length
Operating Requirements: 0-50º C (+32°F to 122°F) ambient temperature, non-condensing, non-corrosive atmosphere
Mounting Kits: Wall or Ceiling Mount: BKT 024 Omnidirectional mount; Optional: Mic Stand Kit: SS-10; or Tripod Stands: SS-11 or SS-6
Warranty: 5 years on transmitter, 90 days on accessories
Approvals: CE, FCC, RoHS, WEEE
Compatible Receivers: WIR RX22-4 Four-Channel Receiver, WIR RX15-2 Two-Channel Receiver, WIR RX18 Two-Channel Receiver
Notes: Specifications: Single end input, volume & tone controls at mid point, 1 kHz, “Music” Preset
NOTE: Specifications subject to change without notice.
MAN 119H
15
Download from Www.Somanuals.com. All Manuals Search And Download.
™
SoundPlus Infrared Listening System
10300 Valley View Rd • Eden Prairie, MN 55344
800-328-6190 / 952-943-2252 • FAX: 952-943-2174
©2012 Williams Sound • All Rights Reserved
MAN 119H
Download from Www.Somanuals.com. All Manuals Search And Download.
|