Williams Sound TV Converter Box WIR 237 User Manual

MANUAL AND USER GUIDE

™

SoundPlus TV Infrared System

Model WIR 237

Model WIR 238

Model WIR 239

Transmitter Model WIR TX238

Receiver Model WIR RX237 or

Receiver Model WIR RX238 or

Receiver Model WIR RX239

MAN 120C

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM OVERVIEW

Thank you for purchasing the SoundPlus^™TV Infrared System

from Williams Sound Corp. Anyone needing auditory assis-

tance to overcome background noise, reverberation, or distance

from the sound source can benefit from the SoundPlus^™TV

Infrared System.

You can use the SoundPlus^™TV Infrared System for hearing

assistance in conference rooms, listening to the TV, or with

other audio equipment. The TX238 Transmitter features an

Automatic Level Control to adjust for different audio signal

levels and to maintain a comfortable listening level.

Please read through this manual carefully

for proper setup and installation instructions.

™

NOTE: The SoundPlus TV Infrared System is not recom-

mended for use with a PLASMA TV MONITOR.

If you have problems at anytime with these systems, do not

hesitate to call us toll-free at 1-800-843-3544.

SYSTEM COMPONENTS

• WIR TX238 Transmitter

• Power Supply

• WIR RX237 or

WIR RX238 or

• TV Microphone (MIC 084)

WIR RX239 Receiver

• 1m Audio Cable with

dual RCA plugs (WCA 078)

• Two Rechargeable Batteries

(BAT AP97A)

Download from Www.Somanuals.com. All Manuals Search And Download.

SAFETY INFORMATION

Hearing Safety:

CAUTION!

This product is designed to amplify sounds to a high volume

level which could potentially cause hearing damage if used

improperly.

To protect your hearing and the hearing of others:

1. Make sure the volume is turned down before putting on the

earphone or headphone before adjusting the volume to a

comfortable level.

2. Set the volume level at the minimum setting that you

need to hear.

3. If you experience feedback (a squealing or howling sound),

reduce the volume setting and move the microphone away

from the earphone or headphone.

4. Do not allow children or other unauthorized persons to

have access to this product.

Download from Www.Somanuals.com. All Manuals Search And Download.

Pacemaker Safety:

CAUTION!

1. Before using this product with a pacemaker or other medical

device, consult your physician or the manufacturer of your

pacemaker or other medical device.

2. If you have a pacemaker or other medical device, make sure

that you are using this product in accordance with safety

guidelines established by your physician or the pacemaker

manufacturer.

RECYCLING INSTRUCTIONS

Help Williams Sound protect the environment! Please take the

time to dispose of your equipment properly.

Product Recycling for Customers in the European Union:

Please do NOT dispose of your Williams Sound equipment in

the household trash. Please take the equipment to an electron-

ics recycling center; OR, return the product to the factory for

proper disposal.

Battery Recycling for Customers in the European Union:

Please do NOT dispose of used batteries in the household trash.

Please take the batteries to a retail or community collection

point for recycling.

04/04/07

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING UP THE TX238 TRANSMITTER

NOTICE: THE RECHARGEABLE BATTERIES ARE SHIPPED IN A DIS-

CHARGED STATE. THE BATTERIES MUST BE CHARGED OVERNIGHT

BEFORE USING THE SOUNDPLUS^™TV INFRARED SYSTEM.

The WIR TX238 Transmitter may be placed on top of a TV or

shelf. Place the TX238 Transmitter where it is clearly visible

from your listening position.

Infrared light behaves like visible light, so it is blocked by solid

objects. This confines the signal to the room where the trans-

mitter is located. The transmitter cannot be placed inside or

behind anything except glass. The maximum operating distance

is approximately 30 feet (9 m).

Ideally, the TX238 Transmitter should be at ear-level height or

above. The infrared light pattern is much like a floodlight

“cone” as it leaves the transmitter, with the best reception

inside the cone.

Sunlight can cause infrared interference in the form of a buzz,

hiss, or static. Thus, the system cannot be used outdoors and

may not work properly inside if a lot of direct sunlight is pres-

ent. Closing drapes or blinds will help if sunlight is a problem.

Any number of receivers may be used with the TX238

Transmitter, but use only one transmitter in a room at the same

time. Otherwise, interference will occur.

Receiver Charging Cradle

Battery

Charging

Port

Battery

Charging

Port

Left

Infrared

Transmitting

Diodes

Receiver

Charging

Indicator

Infrared

Transmitting

Diodes

Right

Battery

Charging

Indicator

Battery

Charging

Indicator

(only for WIR

RX237, RX238,

RX239 Receiver)

Download from Www.Somanuals.com. All Manuals Search And Download.

TX238

TV Microphone

5 _{If an RCA connection is unavail-}

able, use the provided TV micro-

phone to pickup the sound source

directly from the TV loud speak-

er as shown on right.

TX238 Transmitter (Rear View)

STEP 1: CONNECT THE TRANSMITTER POWER SUPPLY

Plug the Power Supply cord into the “DC 12V” jack 1 on the

back of the TX238. Then plug the Power Supply into an AC

outlet. When the receiver is placed into the charging cradle built

into the top of the transmitter, the center charging indicator on

the front of the TX238 will turn on. When the spare battery is

plugged into the left or right battery charging port on the trans-

mitter, the corresponding charge indicator light will turn on.

STEP 2: CONNECT THE TRANSMITTER TO THE AUDIO SOURCE

Use the supplied red and white RCA audio cables to connect the

TX238 Transmitter directly to the TV, VCR, or stereo “AUDIO

OUT” jacks. If your television does not have “AUDIO OUT”

jacks, you will need use the supplied TV microphone. See page

9 for TV microphone instructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 2 (CONTINUED):

NOTE: Some televisions have FIXED output and others have

VARIABLE output. If available, FIXED output should be

selected. Consult your television manual for more information.

“Fixed” output means the volume on the television will not

change when the volume is increased, decreased, or muted.

“Variable” output means the volume on the television will

change when it is increased, decreased, or muted. If variable out-

put is the only output available on your television, we recom-

mend using the supplied TV microphone. See page 9 for TV

microphone instructions.

STEP 3: SELECT STEREO OR MONO OPERATION

Note: Choose 1 of 3 transmitter setup options below and on

page 9. Verify receiver compatibility on left.

Important: If your system is packaged with the WIR RX239

(neckloop) Receiver, you must setup the WIR TX238

Transmitter to operate in 2.3 MHz (mono) mode. See 2.3 MHz

(mono) instructions on page 9. The WIR RX239 (neckloop)

Receiver will NOT work while the transmitter is in stereo or

2.8 MHz mode.

If your system is packaged with the WIR RX237 or WIR RX238

Receiver, you can choose to operate the WIR TX238 in stereo OR

mono (2.3 or 2.8 MHz) operation. For the highest quality, stereo is

the recommended mode of operation.

Compatible with:

STEREO OPERATION:

(HIGHEST AUDIO QUALITY)

Connect the RCA plugs from the TV or VCR

RX237

audio output into the LEFT and RIGHT RCA

-or-

jacks on the TX238 Transmitter 3. Next, slide the

stereo/mono switch 2on the TX238 Transmitter

to the stereo “ ꢀꢀ ” position. Your transmitter is

now set for stereo operation.

RX238

Download from Www.Somanuals.com. All Manuals Search And Download.

Compatible with:

2.3 MHz (MONO) OPERATION:

Connect the LEFT RCA plug from the TV or

VCR audio output into the LEFT RCA jack on the

TX238 Transmitter 3 (the right jack should be

left unplugged). Next, slide the stereo/mono

switch to the “ ꢀ ” mono position 2. The trans-

mitter is now set for 2.3 MHz operation.

RX237

-or-

RX238

-or-

RX239

Compatible with:

2.8 MHz (MONO) OPERATION:

Connect the LEFT RCA plug from the TV or VCR

speaker output into the RIGHT RCA jack on the

TX238 Transmitter 3(the left jack should be left

unplugged). Next, slide the stereo/mono switch 2

to the “ ꢀ ” mono position. The transmitter is now

set for 2.8 MHz operation.

RX237

-or-

RX238

STEP 3 (CONTINUED):

If an RCA connection is unavailable, use the provided

TV MICROPHONE 5 to pickup the desired sound source.

Plug in the microphone into the Mic Jack on the rear of the

TX238 Transmitter 4. Use the velcro strip supplied to attach

the microphone near the loudspeaker 4 of your TV or stereo.

The microphone will allow you to play the TV at lower volume

for other listeners and will pick up other important sounds like

the telephone or doorbell ringing.

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING UP THE RX237 RECEIVER

STEP 1: INSTALL THE RECEIVER BATTERIES

Insert the rechargeable battery into the bottom of the RX237 Receiver

(see page 12). Place the receiver into the charger cradle built into the

top of the TX238 Transmitter and let charge overnight. The spare bat-

tery can be plugged into the charging port located on either side of the

transmitter. By keeping the spare battery charged, you can easily swap

batteries when the one in use runs out and always have a fresh battery

ready. A fully charged battery will operate the receiver for approxi-

mately 6 hours depending on the volume setting. The battery should

be changed when you notice the sound getting weak and noisy. the

batteries may be left charging when not in use.

STEP 2: USING THE WIR RX237 RECEIVER

The RX237 will automatically configure itself for stereo or mono

(2.3 or 2.8 MHz) operation depending on the setup chosen for the

TX238 Transmitter.

Before you use the system, double check to make sure the WIR

TX238 Transmitter’s power supply is plugged in. Make sure the TV,

stereo, or audio source is turned ON. Make sure the receiver’s battery

is fully charged.

To Use the Receiver:

1. First, place the lanyard on the receiver around your neck.

IMPORTANT: a dual detector infrared “eye” is located in the

front of the receiver. Do not cover it up or you will lose reception.

Make sure the “SOUND PLUS” lettering is facing away from

you when you put the receiver on.

2. Next, plug in an earphone, headphone, or neckloop with 3.5mm

plug into the jack on the bottom of the RX237 receiver (see drawing

on page 12). Note: The RX237 turns ON automatically when you

plug in the earphone/headphone into the jack, and turns OFF when

you remove the earphone/headphone from the jack.

3. Rotate the volume control to a comfortable listening level. Note: If

you are using a neckloop with the RX237, turn the volume control to

“2,” or about half of full volume. Then, turn the switch on your hear-

ing aid to the “T” position and adjust the volume to a comfortable

listening level. If the sound is weak, increase the volume on the

RX237 Receiver, then on your hearing aid.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT: When you are done using the RX237, remember

to UNPLUG the earphone, headphone, or neckloop from

the receiver’s jack. The receiver will not turn off until the

earphone/headphone is removed from the unit.

Return the receiver to the charger when it is not in use!

ADDITIONAL RECEIVER ADJUSTMENTS

Balance Control: Use a small screwdriver to adjust the loudness bal-

ance between the Left and Right Earphones. See page 12.

Tone Controls: Use a small screwdriver to adjust the tone for the left

and right earphones. See page 12.

Download from Www.Somanuals.com. All Manuals Search And Download.

Lanyard

RX237 Receiver

(Front View)

Volume

Control

Battery (BAT AP97A)

Optional Earphone/Headphone/Neckloop

for 3.5mm Jack

RX237 Receiver (Rear View)

Tone Controls

Balance Control

–

BAL

RX237 Receiver (Bottom View)

3.5mm Jack

Battery (BAT AP97A)

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING UP THE RX238 RECEIVER

STEP 1: INSTALL THE RECEIVER BATTERIES

Insert the rechargeable battery into the bottom of the RX238

Receiver (see page 14). Place the receiver into the charger cradle

built into the top of the TX238 Transmitter and let charge

overnight. The spare battery can be plugged into the charging

port located on either side of the transmitter. By keeping the

spare battery charged, you can easily swap batteries when the

one in use runs out and always have a fresh battery ready. A fully

charged battery will operate the receiver for approximately 6

hours, depending on the volume setting. The battery should be

changed when you notice the sound getting weak and noisy. The

batteries may be left charging when not in use.

STEP 2: USING THE WIR RX238 RECEIVER

The RX238 will automatically configure itself for stereo or

mono (2.3 or 2.8 MHz) operation depending on the setup cho-

sen for the TX238 Transmitter.

To use the system, first check to make sure your TV or audio

source is turned ON. Make sure the receiver battery is fully

charged. The RX238 Receiver has an automatic on/off function.

When you put the receiver on, it turns on. When you take the

receiver off, it turns off. Rotate the volume control to adjust the

volume to a comfortable level.

IMPORTANT: A dual detector infrared “eye” is located in

the front of the receiver. Do not cover it up or you will lose

reception. Make sure the “SOUND PLUS” lettering is facing

away from you when you put the receiver on.

Return the receiver to the charger when it is not in use.

ADDITIONAL RECEIVER ADJUSTMENTS

Balance Control: Use a small screwdriver to adjust the loudness

balance between the left and right earphones. See page 14.

Tone Controls: Use a small screwdriver to adjust the tone for

the left and right earphones. See page 14.

Ear Cushions: Replacement ear cushions are available from

your Williams Sound dealer, part number EAR 031.

Download from Www.Somanuals.com. All Manuals Search And Download.

RX238 Receiver

(Front View)

Volume

Control

Battery (BAT AP97A)

RX238 Receiver (Rear View)

Tone Controls

Balance Control

–

BAL

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING UP THE RX239 (NECKLOOP) RECEIVER

STEP 1: INSTALL THE RECEIVER BATTERIES

Insert the Rechargeable battery into the bottom of the RX239

Receiver (see drawing on page 16). Place the receiver into the

charger cradle built into the top of the TX238 Transmitter and let

charge overnight. The spare battery can be plugged into the charg-

ing port located on either side of the transmitter. By keeping the

spare battery charged, you can easily swap batteries when the one

in use runs out and always have a fresh battery ready. A fully

charged battery will operate the receiver for approximately 6

hours, depending on the volume setting. The battery should be

changed when you notice the sound getting weak and noisy. The

batteries may be left charging when not in use.

STEP 2: USING THE WIR RX239 RECEIVER

The RX239 Receiver magnetically transfers the audio from the

TX238 Transmitter into a hearing aid equipped with a telephone

coil (T-coil).

Before you use the receiver, double check to make sure the

WIR TX238 Transmitter’s power supply is plugged in. Make sure

the audio connection on the transmitter is set up for 2.3 MHz

(mono) operation only. See pages 8-9. Make sure the TV, stereo,

or audio source is turned ON. Make sure the receiver’s battery is

fully charged.

To use the Receiver:

1) First, place the neckloop on the receiver around your neck.

Important: A dual detector infrared “eye” is located on the

front of the receiver. Do not cover it up or you will lose recep-

tion. Make sure that “SOUNDPLUS” lettering is facing away

from you when you put the receiver on.

2) Turn the receiver ON by turning the volume control to “2,” or

about half of full volume.

3) Turn the switch on your hearing aid to the “T” position and

adjust the volume for comfortable listening.

4) If the sound is weak, increase the volume on the Williams

Sound unit, then on your hearing aid.

Download from Www.Somanuals.com. All Manuals Search And Download.

RX239 Receiver

(Front View)

Neckloop

Volume

Control

Battery (BAT AP97A)

RX239 Receiver (Rear View)

Download from Www.Somanuals.com. All Manuals Search And Download.

CASE OF DIFFICULTY

If the system does not seem to be functioning:

1. Read through the manual and user guide carefully to verify proper

setup and installation of your system.

2. Make sure that your television or VCR is plugged in and

turned on.

3. Make sure that the TX238 Transmitter’s power adapter is plugged in.

4. If you’ve installed the TX238 Transmitter other than on top of the

TV, make sure that its front panel is facing the receiver.

5. Make sure that the receiver has a fully charged battery.

6. Make sure you are not covering the infrared “eye.” Remove any

objects obstructing the line between the TX238 Transmitter and

the receiver. The “SoundPlus” label should be facing towards the

TV while you listen.

7. If you are using the RX237 or RX238 Receiver and getting static

or hiss: Try operating the TX238 Transmitter in MONO (2.3 MHz

or 2.8 MHz) mode. See instructions on page 8.

8. If you are using the RX239 (neckloop) Receiver, and the sound is

weak or noisy: First, make sure that the TX238 Transmitter is

operating in 2.3 (Mono) mode. Also, check that the T-coil switch

on your hearing aid is switched to the “On” position. Next, try

increasing the volume on the receiver unit, then increase the vol-

ume on your hearing aid until the volume is at a comfortable lis-

tening level.

9. If you are operating the TX238 Transmitter in MONO (2.3 MHz

or 2.8 MHz) mode and getting noise or hiss in the receiver: For

2.3 MHz operation, check to make sure you are only using the left

RCA jack on the TX238 Transmitter. For 2.8 MHz operation:

make sure you are only using the right RCA jack on the TX238

Transmitter.

10. If you are using the TV microphone and not getting a signal, try

turning up the TV volume up slightly. Also, try positioning the

TV mic directly over the TV speaker.

11. If the system still does not function, call Williams Sound at:

1-800-843-3544.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

Williams Sound products are engineered, designed and manufactured

under carefully controlled conditions to provide you with many years

of reliable service. Williams Sound warrants the SoundPlus^™TV

Infrared System against defects in materials and workmanship for

FIVE (5) years. During the first five years from the purchase date, we

will promptly repair or replace the SoundPlus^™TV Infrared System.

Microphones, earphones, headphones, batteries, cables, carry cases,

and all other accessory products carry a 90-day warranty. Chargers

carry a one year warranty.

WILLIAMS SOUND HAS NO CONTROL OVER THE CONDI-

TIONS UNDER WHICH THIS PRODUCT IS USED. WILLIAMS

SOUND, THEREFORE, DISCLAIMS ALL WARRANTIES NOT

SET FORTH ABOVE, BOTH EXPRESS AND IMPLIED, WITH

RESPECT TO THE SOUNDPLUS^™TV INFRARED SYSTEM,

INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRAN-

TY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. WILLIAMS SOUND SHALL NOT BE LIABLE TO

ANY PERSON OR ENTITY FOR ANY MEDICAL EXPENSES OR

ANY DIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES

CAUSED BY ANY USE, DEFECT, FAILURE OR MALFUNCTION

OF THE PRODUCT, WHETHER A CLAIM FOR SUCH DAMAGES

IS BASED UPON WARRANTY, CONTRACT, TORT OR OTHER-

WISE. THE SOLE REMEDY FOR ANY DEFECT, FAILURE OR

MALFUNCTION OF THE PRODUCT IS REPLACEMENT OF THE

PRODUCT. NO PERSON HAS ANY AUTHORITY TO BIND

WILLIAMS SOUND TO ANY REPRESENTATION OR WARRAN-

TY WITH RESPECT TO THE SOUNDPLUS^™TV INFRARED

SYSTEM. UNAUTHORIZED REPAIRS OR MODIFICATIONS

WILL VOID THE WARRANTY.

The exclusions and limitations set out above are not intended to, and

should not be construed so as to contravene mandatory provisions of

applicable law. If any part or term of this Disclaimer of Warranty is

held to be illegal, unenforceable or in conflict with applicable law by a

court of competent jurisdiction, the validity of the remaining portions

of this Disclaimer of Warranty shall not be affected, and all rights and

obligations shall be construed and enforced as if this Limited Warranty

did not contain the particular part or term held to be invalid.

Download from Www.Somanuals.com. All Manuals Search And Download.

If you experience difficulty with your system, call Toll-Free for

Customer Assistance:

1-800-843-3544

If it is necessary to return the system for service, your Customer

Service Representative will give you a Return Authorization Number

(RA) and shipping instructions.

Pack the system carefully and send it to:

Williams Sound Corp.

Attn: Repair Dept.

10321 West 70th Street

Eden Prairie, MN 55344

Download from Www.Somanuals.com. All Manuals Search And Download.

WIR 238, WIR 239

SYSTEM SPECIFICATIONS:

WIR TX238 Transmitter:

Size, Weight, Color:

6.25”L x 3.25”W x 1.25”H (15.9cm x

8.3cm x 3.2cm), 5.1oz. (140g), Gray

Power Input:

12 VDC (center is positive), 200 mA Class

II wall transformer

TFP 024 Power Supply: North America:

120VAC, 60Hz, UL/CSA

TFP 032 Power Supply, 2 pin Euro mains

plug, 230VAC, 50-60 Hz, CE

TFP 033 Power Supply, 3 pin UK mains

plug, 230VAC, 50-60 Hz, CE

Subcarrier Frequency:

Range:

2.3 MHz, 2.8 MHz, or stereo.

30ft. (9m) line-of-site

Auto Power On/Off:

Transmitter shuts off infrared after 1.5 min-

utes when audio signal is removed. Battery

charging functions remain on full time.

Microphone Input:

Line Inputs:

3.5 mm jack for MIC 084 Electret TV

Microphone, 1.5 kΩ

2 RCA jacks for mono or stereo line-level

sources

200 mV min. to 10 V rms max. input level,

5.1 kΩ

Automatic Level Control:

Infrared LEDs, Pattern:

35 dB compression range

8 IR LEDs, 45 degree cone-shaped cover-

age pattern to 6dB intensity,

30ft. (9m) line of sight

Charging Ports:

Charges one WIR RX238 Receiver plus

two additional BAT AP97A NiMH battery

packs

Approvals:

Warranty:

RoHS, WEEE

5 years*

*90 days on cords, batteries, power supply and other accessories.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIR RX237 Receiver:

Weight:

1.7 oz (50 g) with battery

ABS plastic, Black

BAT AP97A NiMH Battery Pack, 6 hours

2.3 and 2.8 MHz

200 Hz to 8 kHz, 5 dB

60 dB at 9m

Volume control thumbwheel; screwdriver

adjust balance

Material and Color:

Battery Type, Life:

Modulation Frequency:

Frequency Response:

Signal-to-Noise Ratio:

Controls:

and (L & R) tone controls

115 dB MAX SSPL90 with EAR 013 (2cc

coupler)

Compatible with transmitters operating on

2.3 MHz/2.8 MHz

Acoustic Output:

Compatibility:

Power Switch:

Approvals:

Warranty:

Built into jack

RoHS, WEEE

5 years, parts and labor*

WIR RX238 Receiver:

Weight:

2.1 oz (60 g) with batteries

ABS plastic, Black and Grey

BAT AP97A NiMH Battery Pack, 6 hours

2.3 MHz and/or 2.8 MHz

200 Hz to 8 kHz, 5 dB

60 dB at 30 ft. (9m)

Volume control thumbwheel; screwdriver

adjust balance and (L & R) tone controls

112 dB MAX SSPL90 with 2 cc coupler

Compatible with transmitters operating on 2.3

MHz, 2.8 MHz, or both (stereo)

Built into receiver “arms”

Uses EAR 031 foam cushions

RoHS, WEEE

5 years*

Material and Color:

Battery Type, Life:

Modulation Frequency:

Frequency Response:

Signal to Noise Ratio:

Controls:

Acoustic Output:

Compatibility:

Power Switch:

Ear pads:

Approvals:

Warranty:

*90 days on cords, batteries, power supply and other accessories.

Download from Www.Somanuals.com. All Manuals Search And Download.

WIR RX239 Receiver:

Weight:

2.2 oz (64 g) with batteries

ABS plastic, Black

BAT AP97A NiMH Battery Pack, 6 hours

2.3 MHz

200 Hz to 8 kHz, 5 dB

60 dB at 30 ft. (9m)

Volume control thumbwheel

Compatible with most wide-band 2.3 MHz

Transmitters

Material and Color:

Battery Type, Life:

Modulation Frequency:

Frequency Response:

Signal to Noise Ratio:

Controls:

Compatibility:

Power Switch:

Loop Length:

Approvals:

Built into volume control

32”

RoHS, WEEE

Warranty:

5 years*

*90 days on cords, batteries, power supply and other accessories.

Download from Www.Somanuals.com. All Manuals Search And Download.

10321 West 70th St., Eden Prairie, MN 55344 U.S.A.

800.843.3544 | 952.943.2252 | FAX: 952.943.2174

www.williamssound.com

MAN 120C

Download from Www.Somanuals.com. All Manuals Search And Download.

Weed Eater Trimmer 530086901 User Manual
Weslo Treadmill WLTL11092 User Manual
West Bend Slow Cooker 6 QT User Manual
Whirlpool Air Conditioner AC1052XS User Manual
White Rodgers Marine Radio 37 6334a User Manual
Wyse Technology Computer Monitor 2510SE User Manual
Xerox Printer Accessories 6125N User Manual
Yamaha Drums DD 5 User Manual
Yamaha Outboard Motor LX150Y User Manual
Zanussi Freezer ZRD 7846 User Manual