MODEL:
Natural Gas
2903512
MODEL:
Propane Gas
2903511
Installation Instructions and Owner’s Manual
Direct-Vent Wall Furnace
WARNING: Improper installation, adjustment,
alteration, service, or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional
information, consult a qualified installer,
service agency or the gas supplier.
WARNING: If the information in this
manual is not followed exactly; a fire
or explosion may result, causing
property damage, personal injury or
loss of life.
- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Open all windows.
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Extinguish any open flame.
WARNING: Installation and repair must be
done by a qualified service person. The
furnace should be inspected before use and at
least annually by a professional service
person.
• Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
• If you cannot reach your gas supplier,
call the fire department.
- Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
WARNING: If not installed, operated and
maintained in accordance with the
manufacturer’s instructions, this
product could expose you to substances in
fuel or from fuel combustion which can cause
death or serious illness and which are known
to cause cancer, birth defects or other
reproductive harm.
Williams Furnace Co., 250 West Laurel Street, Colton, CA 92324 U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Rules and General Warnings
DO NOT OPERATE THIS FURNACE WITHOUT THE FRONT PANEL INSTALLED
•
•
Due to high temperatures, the furnace should be
located out of traffic and away from combustible
materials such as furniture and draperies.
•
More frequent cleaning may be required due to excessive
lint from carpeting, bedding materials, etc. It is imperative
that control compartments, burners and circulating air
passageways of the furnace be kept clean.
Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
•
•
DO NOT put anything around the furnace that will obstruct
the flow of combustion and ventilation air.
•
•
•
Young children should be carefully supervised
when they are in the same room as the furnace.
DO keep the furnace area clear and free from combustible
materials, gasoline and other flammable vapors and
liquids.
Clothing or other flammable material should not be
placed on or near the furnace.
•
•
•
DO examine venting system periodically and replace
damaged parts.
Any safety screen or guard removed for servicing
an furnace must be replaced prior to operating the
furnace.
DO examine burner periodically. Clean and replace
damaged parts.
•
•
Keep burner and control compartment clean.
DO NOT use this furnace if any part has been under water.
Immediately call a qualified service technician to inspect
the furnace and to replace any part of the control system
and any gas control which has been under water.
The outside vent cap is hot while furnace is in
operation.
•
Installation and repair should be done by a
QUALIFIED SERVICE TECHNICIAN. The furnace
should be inspected before use and at least
annually by a qualified service technician.
Safety Information for Users of LP Gas
Propane (LP Gas) is a flammable gas which can cause fires and explosions. In its natural state, propane is odorless and
colorless. You may not know all the following safety precautions which can protect both you and your family from an accident.
Read them carefully now, then review them point by point with the members of your household. Someday, when there may
not be a minute to lose, everyone’s safety will depend on knowing exactly what to do. If, after reading the following information,
you feel you still need more information, please contact your gas supplier.
LP Gas Warning Odor
If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP Gas.
That’s your signal to go into immediate action!
•
•
•
•
Do not operate electric switches, light matches or use your phone. Do not do anything that could ignite the gas.
IMMEDIATELY get everyone out of the building, vehicle, trailer or area.
Close all gas tank or cylinder supply valves.
LP Gas is heavier than air and may settle in low areas such as basements. When you have reason to suspect a gas
leak, keep out of basements and other low areas. Stay out until firefighters declare them to be safe.
Use your neighbor’s phone and call a trained LP Gas service technician and the fire department. Even though you may
not continue to smell gas, do not turn on the gas again. Do not re-enter the building, vehicle, trailer or the area.
Have the service technician or fire department air out the area before you return. A properly trained LP Gas service
technician must repair the leak, check and relight the gas furnace for you.
•
•
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Some Points to Remember
•
•
•
•
Learn to recognize the odor of LP Gas. Your local LP Gas Dealer can give you a ”Scratch and Sniff” pamphlet. Use
it to find out what the propane odor smells like. If you suspect that your LP Gas has a weak or abnormal odor, call
your LP Gas Dealer.
If you are not qualified, do not light pilot lights, perform service, or make adjustments to furnaces on the LP Gas
system. If you are qualified, consciously think about the odor of LP Gas prior to and while lighting pilot lights or
performing service or making adjustments.
Sometimes a basement or a closed–up house has a musty smell that can cover up the LP Gas odor. Do not try to
light pilot lights, perform service or make adjustments in an area where the conditions are such that you may not detect
the odor if there has been a leak of LP Gas.
Odor fade, due to oxidation by rust or absorption on walls of new cylinders and tanks, is possible. Therefore, people
should be particularly alert and careful when new tanks or cylinders are placed in service. Odor fade can occur in
new tanks or reinstalled old tanks if they are filled and allowed to set too long before refilling. Cylinders and tanks
which have been out of service for a time may develop internal rust which will cause odor fade. If such conditions
are suspected to exist, a periodic sniff test of the gas is advisable. If you have any question about the gas odor,
call your LP Gas dealer. A periodic sniff test of the LP Gas is a good safety measure under any condition.
If, at any time, you do not smell the LP–Gas odorant, and you should, assume you have a leak. Then take
the same immediate action recommended above for the occasion when you do smell the odorized LP Gas.
If you experience a complete ”gas out” (the container is under no vapor pressure), turn the tank valve off immediately.
If the container valve is left on, the container may draw in some air through openings such as pilot light orifices.
If this occurs, some new internal rusting could occur. If the valve is left open, then treat the container as a new tank.
Always be sure your container is under vapor pressure by turning it off at the container before it goes completely
empty or having it refilled before it is completely empty.
•
•
Technical Data
mbar
in W.C.
mbar
in W.C.
mbar
in W.C.
mbar
in W.C.
m3/h
ft3/h
m3/h
ft3/h
m3/h
ft3/h
kW
6.98
23,817
8.5
8.0
3.2
26.5
10.6
4.6
1.8
16.2
6.5
.9
NATURAL
GAS
OUTPUT HEATING CAPACITY
kBTU/hr
kW
MAX
MIN
INPUT RATING (High Input)
LP
kBTU/hr
kW
29,000
5.89
MINIMUM INPUT RATING
(Low Input)
NATURAL
GAS
kBTU/hr
%
20,100
82
THERMAL EFFICENCY
LENGTH
LP
mm
in
1006
39-5/8”
715
NATURAL
GAS
mm
in
30.1
.3
HEIGHT
DEPTH
MAX
28-1/8”
208
LP
mm
in
11.6
.6
8-1/4”
42
NATURAL
GAS
kg
21.3
.2
WEIGHT
m3/h
MIN
lbs.
93
LP
½”
GAS CONNECTION
WALL HOLE DIAMETER
NPT
ft3/h
8.7
FEMALE
mm
in
50
2”
mbar
in W.C.
mbar
in W.C.
m³/h
cfm
17.4
7.0
NATURAL
GAS
MINIMUM INLET
PRESSURE
mm
in
49
27.4
11.0
450
265
330
194
AIR INLET DIAMETER
EXHAUST PIPE DIAMETER
MAX WALL THICKNESS
MIN WALL THICKNESS
LP
1-7/8”
35
mm
in
AIR FLOW
1-3/8”
500
mm
in
m³/h
cfm
MINIMUM AIR FLOW
19-5/8”
150
mm
in
5-7/8”
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation should be done by a QUALIFIED SERVICE TECHNICIAN.
The furnace must be located on an outside wall.
WARNING: For the installation of this furnace, the
following items must be used as a vent air intake
system:
Wall Installation
Minimum clearances from combustible materials:
External Vent Cap
(Part Number: WFR–TRM000)
Flanged Air Inlet Tube
(Part Number: WFR–TBO002)
O-Ring
•
•
•
•
•
Furnace to the top surface of carpeting, tile:
2-inches (50 mm)
Furnace to back wall (0” to spacers):
0-inch (0 mm).
Vent to wall enclosure:
0-inch (0 mm)
Furnace to sidewalls:
3.15-inches (80 mm)
(Part Number: WFN–RNG003)
Flue Outlet Tube
(Part Number: WFR-795)
Furnace to ceiling:
(All the above items are supplied with the furnace)
10-inches (254 mm)
See Figure 1 showing clearance for installation of vent cap.
Leave at least three-feet in front of the wall furnace for servicing and proper operation. The wall furnace must be installed in such
a way that the external casing can be completely removed for servicing.
If there is a shelf above the furnace, it must be be noncombustible. A minimum clearance of 12-inches (300 mm) is
recommended between the furnace and the noncombustible shelf above it.
Gas equipment in residential garages must be installed so that all burners and burner ignition devices are located not less than
18-inches (460 mm) above the floor. Such equipment must be located, or protected, so it is not subject to physical damage by a
moving vehicle.
The vent terminal of this direct-vent furnace must be located at least 9-inches (230 mm) from any opening through which flue
gases could enter a building. The bottom of the vent terminal and the air intake must be located at least 12-inches (300mm)
above grade.
DO NOT cover the furnace.
Make sure that the correct gas supply is available.
The furnace requires a 120V, 60 Hz electrical supply.
The furnace must be electrically grounded in accordance with local codes or in the absence of local codes, with the National
Electrical Code ANSI/NFPA 70 (latest edition) or in Canada with CAN/CSA-C22.2 No. 3.
WARNING: The nearest point of the vent cap should be a minimum horizontal distant of six (6) feet (1,830 mm)
from any pressure regulator. In case of regulator malfunction, the six (6) feet (1,830 mm) distance will reduce
the chance of gas entering the vent cap.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 1
1 = Fixed/Closed
2 = Openable
V = Vent Terminal
A = Air Supply
A. Clearance above grade, veranda, porch, deck or
balcony 12-inches (30 cm) minimum. (3)
K. Clearance to a mechanical air supply inlet 6-feet (1.8 m)
minimum. (3)
B. Clearance to window or door that may be opened 12-
inches (30 cm) minimum. (3)
L. Clearance (1) above paved sidewalk or a paved driveway
located on public property 7-feet (2.1 m) minimum. (3)
C. Clearance to permanently closed window (minimum 12- M. Clearance under veranda, porch, deck or balcony 12-
inches (30 cm) recommended to prevent condensation
on window.
inches (30 cm) minimum. (2), (3)
D. Vertical clearance to ventilated soffit located above the
terminal within a horizontal distance of 2-feet (60 cm)
from the centerline of the terminal 18-inches (46 cm)
minimum.
Notes:
(1)
(2)
(3)
A vent must not terminate directly above a sidewalk
or paved driveway which is located between two
single family dwellings and serves both dwellings.
E. Clearance to unventilated soffit 12-inches (30 cm)
minimum clearance to vinyl soffit 36-inches (90 cm)
minimum.
Only permitted if veranda, porch, deck or balcony is
fully open on a minimum of two sides beneath the
floor.
F. Clearance to outside corner 12-inches (30 cm)
minimum.
As specified in CGA B149 installation codes (1991).
Note: Local codes or regulations may require different
clearances.
G. Clearance to inside corner 18-inches (46 cm) minimum.
H. Not to be installed above a meter/regulator assembly
within 3-feet (90 cm) horizontally from the centerline of
the regulator. (3)
I. Clearance to service regulator vent outlet 6-feet (1.8 m)
minimum. (3)
J. Clearance to nonmechanical air supply inlet to building
or the combustion air inlet to any other furnace 12-
inches (30 cm) minimum. (3)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Outside Location for Vent Terminal
Upon delivery, check to make sure the packaging has not been damaged.
1. Remove the furnace from box/packaging taking care not to damage the paper template to be used to mark the holes for
mounting the furnace.
2. After marking the appropriate holes using the above mentioned template, make a 2-inch diameter hole.
3. Cut the combustion exhaust and fresh air inlet tubes according to the wall thickness (Figure 2):
Air Inlet Tube Length
Flue Outlet Tube Length
=
=
Wall Thickness + 3/32-inch
Wall Thickness + 1-5/16 inches
F
Figure 2
A + 33.3 mm
A + 2.3 mm
4. Drill the mounting holes “A” (8 holes) in the wall. If possible, use self-tapping screws, drill 1/8-inch diameter holes. If
self-tapping screws cannot be used, drill 1/4-inch diameter holes and use the plastic anchors provided.
5. Install the supporting bracket to the wall; insert the air pipe in the wall through the hole provided in the support bracket.
Place the round adhesive gasket around the hole, so that the air pipe remains in its position.
6. Attach the supporting bracket with the screws provided. If possible, use self-tapping screws, drill 1/8-inch diameter
holes. If self-tapping screws cannot be used, use the plastic anchors provided.
7. Remove the casing loosening the screws and disconnect the casing grounding cable.
8. Place the adhesive spongy lining behind the furnace. (Figure 3)
Figure 3
9. Attach the flue exhaust flue pipe end (diameter 1” 3/8) on the furnace pipe male connection (Figure 5).
BE SURE THAT THE RUBBER SILICONE O–RING GASKET IS IN POSITION.
10. Remove the front panel by loosing the lateral screws (Figure 4).
11. Install the furnace to the wall leaning the bottom edge of panel “C” (where the fan is located) on the supporting frame, as
shown in Figure 6. Attach the furnace to the matching hooks “A”, with light pressure against the wall). Install the
heating body of the furnace to the supporting bracket with the two lateral screws.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4
O-Ring Gasket
Figure 5
Figure 6
12. When the inside installation is complete, proceed to the outside location of the aluminium vent cap on the external wall.
The vent cap should perfectly match the pipe end. Mark the location of the three holes for the screw anchors. (Figure 7)
The flue grid must be vertical.
13. Remove the vent cap and drill all the necessary holes (diameter 1/4 in. for the screw fittings provided with the furnace).
14. Position the vent cap and attach it with the screws (Figure 7).
15. Connect the female end of the three-prong plug to the furnace connection on the bottom of the furnace.
16. Connect the gas supply line. A gas tap must before the connection to the furnace must be installed.
17. Reattach the front panel. (Figure 4)
18. Reconnect the grounding wire to the casing and reinstall the casing then tighten the screws.
19. Turn on gas supply and check for gas leaks with soapy water on all gas connections. Seal any leaks prior to operating
the furnace.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Conversions
Converting to another gas type must be performed by a qualified service technician. If the type of the gas supplied to the
dwelling is not the same type as your furnace (natural or LPG gas), it must be converted.
It will be necessary to do the following:
1. Change nozzle.
a. Remove the screw indicated
to the right.
2. Without removing anything else, remove the nozzle from the burner inserting the screwdriver as indicated by the arrow.
Nozzle
3. Change the nozzle, attach the screw indicated at point 1 and set the burner pressure as indicated in the table below:
Gas Type
Natural Gas
LP Gas
Nozzle Part Number
JGLL069
Nozzle Diameter
0.1 in.
JGLL062
0.06 in.
Minimum Inlet Line Gas
Pressure
Maximum
Manifold Gas Pressure
Minimum
Manifold Gas Pressure
Gas Type
Natural Gas
LP Gas
7.0-inches w.c.
11.0-inches w.c.
3.2-inches w.c.
10.6-inches w.c.
1.8-inches w.c.
6.5-inches w.c.
4. Check the gas pressure and settings.
Minimum Burner Pressure Setting:
1. Set LOW burner capacity by pressing button Z2
2. Connect a micro manometer to the test gauge B (Figure 8)
3. Rotate the internal screw “D” (Figure 8) and set the pressure at the correct value
Maximum Burner Pressure Setting:
1. Set HI burner capacity by pressing button Z2
2. Connect a micro manometer to the test gauge B (Figure 8)
3. Rotate the external screw “C” (Figure 8) and set the pressure at the correct value
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas Supply
Check all local codes for requirements, especially for the size and type of gas supply line required. On natural gas lines less than
15” (380 mm) long, use 1/2” tube; on longer runs, use 3/4” iron tube or equal. On LP gas lines, consult LP gas supplier.
Installing a New Main Gas Shutoff Valve
Each appliance should have its own manual gas shutoff valve. A manual main gas shutoff valve should be located in the vicinity
of the furnace. Where none exists, or where its size or location is not adequate, contact your local authorized installer for
installation or relocation.
Compounds used on threaded joints of gas piping must be resistant to the action of propane (LP) gas. The gas lines must be
checked for leaks by the installer. This should be done with a soap solution watching for bubbles on all exposed connections,
and if unexposed, a pressure test should be made. Repair all leaks prior to operating the furnace.
Never use an exposed flame to check for leaks. Appliance must be disconnected from piping at inlet of control valve
and pipe capped or plugged for a pressure test. Never pressure test with appliance connected; the control valve will
sustain damage!
A gas shutoff valve and ground joint union should be installed in the gas line upstream of the gas control to aid in servicing. It is
required by the National Fuel Gas Code that a drip line be installed near the gas inlet. This should consist of a vertical length of
pipe tee connected into the gas line that is capped on the bottom in which condensation and foreign particles may collect.
The use of the following gas connectors is recommended:
– ANSI Z21.24 Appliance Connectors of Corrugated Metal Tubing and Fittings, CGA 6.10
– ANSI Z21.45 Assembled Flexible Appliance Connectors of Other than All–Metal Construction.
The above connectors may be used if accepted by the local codes or authority having jurisdiction.
Pressure Testing of the Gas Supply System
1. To check the inlet pressure to the gas valve, a plugged tapping, accessible for test gauge connection, is provided on the
gas valve (Figure 8).
2. The appliance and its individual shutoff valve must be disconnected from the gas supply piping system during any pressure
testing of in excess of 1/2 psig (3.5 kPa).
3. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any
pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).
Attention: If any of the above procedures results in pressures in excess of 1/2 psig (14” w.c., 3.5 kPa) on the appliance gas
valve, it will result in a hazardous condition.
High Altitudes (U.S. Only)
For altitudes/elevations above 2,000 feet (610 m), ratings should be reduced at the rate of 4 percent for each 1,000 feet (305 m)
above sea level by reducing the manifold pressure at a rate of 8% on the gas supply. Maximum altitude allowed for installation is
5,500 feet (1680 m).
High Altitudes (Canada Only)
The appliance is tested according to CGA 2.17 M91 for installation between 0 and 4,500 feet (0 and 1370 m) altitude. For
altitudes/elevations above 2,000 feet (610 m), ratings should be reduced at the rate of 4 percent for each 1,000 feet (305 m)
above sea level by reducing the manifold pressure at a rate of 8% on the gas supply. Maximum altitude allowed for installation is
5,500 feet (1680 m).
High Altitude Adjustment
Based on the altitude of the installation site, reduce the manifold pressure specified in the “Technical Data” chart and as
shown in the table below:
Manifold Pressure
Altitude
Reduction Rate
0-2,000 ft
0%
8%
16%
24%
32%
2,000-3,000 ft
3,000-4,000 ft
4,000-5,000 ft
5,000-5500 ft
9
Download from Www.Somanuals.com. All Manuals Search And Download.
First Firing of the Furnace
Start the furnace following the instructions given in the “Operating Instructions“. The initial pilot lighting may be difficult due to air
trapped in the gas lines. During initial firing of the furnace, residual manufacturing grease will bake-out and smoke will occur
which is not a health danger. To prevent nuisance and operation of fire alarms, ventilate the room for the first two hours of
operation.
Checking the Gas Inlet Pressure
The gas inlet pressure can be measured by connecting a test gauge to the connection provided on the gas valve. (Figure 8 - A)
Once installation is complete, the gas inlet pressure must be checked. The minimum gas inlet pressure must be as shown in
“Technical Data”. After checking the gas inlet pressure, disconnect the test gauge and firmly tighten the screw of the gauge
connection, then check for gas leaks.
Checking the Gas Manifold Pressure
The gas manifold pressure can be measured by connecting a test gauge to the connection provided on the gas valve. (Figure 8).
The furnace comes set from the factory at the correct manifold gas pressure. After the installation is completed, the gas
9
manifold pressure must be checked both in Hi and Lo input. The gas manifold pressure must be as shown in the “Technical
Data”. Differences of plus or minus 0.1 in. w.c. are accepted. If the Hi or Lo gas manifold pressures are different from the
values given in the “Technical Data” table, or are more than 0.1 in. w.c., shut off the furnace and contact a qualified service
technician for correction. For instructions about adjustment of the manifold Hi and Lo pressures, see the “Servicing” section.
After checking the gas manifold pressure, disconnect the test gauge and firmly tighten the screw of the gauge connection and
then check for gas leaks from it.
A
B
C
D
E
G
H
L
Test Gauge Connection for Gas Inlet Pressure
Test Gauge Connection for Gas Manifold Pressure
Nut for Hi Pressure Adjustment (Pressure Regulator)
Screw for Lo Pressure Adjustment (Hi – Lo Operator)
Electric Clamp Connection
Electric Cable Inlet
Hole for Gas Supply Inlet
Flame View
L
B
A
D
C
E
H
G
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Wiring
EV
GAS VALVE 1 (SAFETY SHUTTER)
SF
SB
TR
Z1
Z2
Z3
Z8
Z9
L1
L2
FLAME VIEW LAMP (GREEN LAMP)
LOCK-OUT LAMP (RED LAMP)
EV1
EV2 HI-LO FLAME OPERATOR (*)
CURRENT TRANSFORMER 120-24 V
RESET AND SUMMER – WINTER SWITCH (*)
HI-LO FLAME AND FAN SPEED SWITCH (*)
MANUAL – PROGRAM MODE SWITCH (*)
PROGRAMMABLE TIMER (*)
M
FAN MOTOR (n. 2 MOTORS ON 8001/8002)
OVERHEAT THERMOSTAT
FAN THERMOSTAT
M1
M2
M9
NP
MAINS FUSE – 5X20 size – 4A
PRESSURE SWITCH
ROOM THERMOSTAT
RP8 FLAME SENSOR
SUPPLY LINE – LIVE WIRE
RP7 SPARK IGNITER (n. 2 pcs)
SUPPLY LINE – NEUTRAL WIRE
S
COMBUSTION BLOWER MOTOR
GND SUPPLY LINE – GROUND WIRE
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Instructions
Before operating the furnace, read carefully all warnings and safety information in this manual.
FOR YOUR SAFETY READ BEFORE OPERATING
If you do not follow these instructions exactly, a fire or explosion
WARNING:
may result causing property damage, personal injury or loss of life.
A. This appliance does not have a pilot which must
Follow the gas supplier's instructions.
- If you cannot reach your gas supplier, call the fire
department.
be lighted by means of the piezo igniter installed
on the furnace. Do not try to light the pilot by
hand.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or
turn by hand, do not try to repair it, call a qualified
service technician. Force or attempted repair may result
in a fire or explosion.
B. BEFORE LIGHTING, smell all around the
appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than
air and will settle on the floor.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system and any gas control which has been
under water.
WHAT TO DO IF YOU SMELL GAS:
- Do not try to light any appliance
- Do not touch any electric switch
- Do not use any phone in your building
- Immediately call your gas supplier from a
neighbor's phone.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Set the thermostat to the lowest setting by turning it counterclockwise
completely. Do not force.
GREEN
LAMP
RED
LAMP
G
R
3. Turn off all electric power to appliance.
4. This appliance is equipped with an ignition device that automatically lights the
burner. Do not try to light the burner by hand.
MANUAL/PROGRAMMED
BUTTON
5. Turn off gas supply to the unit by turning off the gas shutoff valve.
6. Wait five minutes to clear out any gas. If you then smell gas, STOP! Follow
the safety information in section "B" above. If you do not smell gas, go to the
next step.
THERMOSTAT
SUMMER/WINTER
BUTTON
7. Turn on the gas supply to the unit.
RESET
8. Turn on electric power to the appliance.
9. Push the MIN/MAX button to MIN position (button down).
10. Switch the SUMMER/WINTER button to WINTER position (button up).
11. Set thermostat to desired setting.
MIN
MIN/MAX
BUTTON
MAX
12. The red lamp will be lit for 40 seconds, then the flame ignite. The red lamp
will then shut off and the green lamp will be lit.
13. If the appliance will not operate, follow the instructions below "To Turn Off Gas Of Appliance" and call your
service technician or gas supplier.
14. If you choose the high heat output setting, push the MIN/MAX button to MAX position (button up). If you
prefer soft heating and silent operation, keep it on MIN position (button down).
15. This appliance has an automatic flame control system. When the flame is lit, the green lamp is lit also.
In case of flame fault, the red lamp will light and the green lamp will turn off. If this occurs, set the
SUMMER/WINTER button to the SUMMER position (button down) and wait ten (10) seconds; then turn
the switch back to the WINTER position (button up). The appliance will attempt to relight after
approximately 40 seconds. During these 40 seconds the red lamp will be lit. If the second attempt is
unsuccessful, turn off the electric power to the appliance and call your Service Agency.
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to the lowest setting by turning it counterclockwise
2. Turn off all electric power to the appliance if service is to be performed.
3. Turn the gas tap installed on the gas supply to the CLOSED position.
completely. Do not force.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT TO DO IF THE RED LAMP IS LIT
This appliance has an electronic flame supervision device. If the flame disappears the gas flow will be automatically
shut off and the red lamp will light instead of the green one. The appliance will attempt to relight if you do
the following:
of
ONE
A. Turn off the electric supply to the appliance for approximately 40 seconds and turn it on again;
OR
B. Turn the thermostat knob to the zero setting, then turn it back to a comfortable setting after approximately 40
seconds;
OR
C. Press the SUMMER/WINTER button to the SUMMER position (button down) for approximately 40 seconds and
set it back (button up) to the WINTER position.
HOW TO SHUT OFF THE APPLIANCE
1. Turn the thermostat knob to the ZERO position.
2. Turn the I-O switch on the programmable clock to the ZERO position.
3. Turn off all electric supply to the appliance.
4. Turn the gas shutoff valve installed on the gas supply line upstream to the unit to the CLOSED position.
USING THE FEATURES OF YOUR
FURNACE
: It is lit when the flame is ON.
GREEN LAMP
: In case the flame disappears, the gas flow will be shut off and the red
RED LAMP
lamp will be lit. The furnace is locked-out. To reset the furnace, follow the instructions
above, "WHAT TO DO IF THE RED LAMP IS LIT."
When the button is down, the furnace keeps the
MANUAL/PROGRAM BUTTON:
temperature set by the thermostat according to the clock's program. When the
button is up, the furnace thermostat maintains the temperature.
Turn clockwise to increase the temperature, turn counterclockwise
THERMOSTAT:
to decrease it.
When the button is up, the furnace will operate in heating mode
SUMMER/WINTER:
according to the thermostat and/or clock's program. When the button is down, the
appliance will provide ventilation.
RESET
For faster heating, keep this button up. For soft heating and
silent operation, keep this button down.
MIN/MAX BUTTON:
MIN
MAX
HUMIDIFIER:
water filling hole
For better comfort this furnace is equipped with a humidifier. It is very
HUMIDIFIER:
easy to use. Using a funnel, periodically add water to the small tank located on the
top left side of the furnace. Normally, the tank needs to be refilled after 4 - 5 days.
The use of water low in limestone or distilled is advisable in order to prevent
NOTE:
any possible calcareous sedimentation that may be difficult to remove.
Anticalcareous tablets for humidifiers are commercially available. The humidifier
capacity is 11.8 fluid ounces (0.35 liters).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Servicing
All servicing activities must be carried out by a qualified service technicial or a service agency. The home owner may not
service the furnace. The home owner must read this section to be informed of the periodic maintenance and checks the
required. All servicing (except on vent system) must be carried out with the external casing removed. After any servicing, the
external casing must be reinstalled properly and the grounding wire of the external casing reconnected.
Checking and Adjusting the Gas Manifold Pressure
The furnace comes set from the factory at the correct HI and LO gas manifold pressures as shown in “Technical Data”. It is
recommended to check the pressures periodically (minimum once a year). If adjustment is required, this can be done by
adjusting screws “C” and “D”. (Figure 8) A test gauge must be connected as explained in “Checking the Gas Manifold
Pressure”.
Proceed as follows:
1. Place the furnace on and in the HI mode (knob in HI position).
2. Completely turn down screw “C” (HI – LO operator adjustment) by turning it clockwise. Do not force.
3. Adjust the HI pressure by turning the screw D (pressure regulator) to the value given in the “Specifications”
table. Turn clockwise to increase the pressure, turn counterclockwise to decrease it.
4. Switch the furnace to LO mode (button MAX–MIN down).
5. Loosen screw “C” until the correct value for the LO pressure is achieved.
6. Switch the furnace between LO to HI mode to verify that both the HI and LO pressures are correct. A tolerance
of plus or minus 0.1 in. w.c. on the pressure value is acceptable. Readjust starting from point 1 if needed.
7. Disconnect the test gauge and firmly tighten the screw of the gauge connection. Check for gas leaks with a
soapy water solution and correct any leaks prior to operating the furnace.
The HI and LO pressures must be adjusted as explained above. Never try to adjust them independently from each other.
Checking, Removing and Reassembling of the Vent Air Intake System
It is essential that the vent air intake system is examined periodically (minimum once a year) to verify it is clean from dust and
deposits of solid materials such as leaves or nests. The vent air intake system is checked from outside. Proceed as follows:
1. Remove the vent cap by removing the three outer screws. (Figure 7)
2. Remove the inner flue pipe. Do not use tools; the pipe can be extracted by hand.
3. Remove dust and desposits from the vent cap and flue pipes. Deposits in the air pipe must be taken outside.
Do not push them inside the furnace. The outer air pipe may not be removed from outside.
4. Check the O-ring gasket in the flue pipe. If it is damaged in must be replaced (Part No. WFN-RNG003).
5. Reinstall the flue pipe from outside. Do not use glue or sealants.
6. Reinstall the vent cap on the flue pipe. Do not use glue or sealants. Tighten the three outer screws.
Lubrication of Moving Parts
This furnace does not require lubrication. Do not try to lubricate any part of the furnace such as motors bearings, keys, knobs,
screws, etc.
Flame Visual Check
Correct and proper operation of the burner may be checked by examinng the burner flame. Check the burner flame anytime the
external casing is removed from the furnace. The flame may be examined through the flame viewer. (Figure 8) The flame must
be stable and have blue color. Some small yellow tips are acceptable with propane gas. If the flame is yellow or has excessive
turbulence, check the gas manifold pressure and the vent air intake system. If all these are acceptable, call a qualified service
technician for a complete check of the furnace. Call also your gas supplier to check the composition of the gas in use.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Annual Maintenance Requirements
1. Clean fan blades.
2. Clean air blower.
3. Check and clean silicone red pipes.
4. Check air flow switch.
5. Clean and check exhaust flue pipe and air intake pipe.
Check red O-Ring Gasket
(NRNG003). If it is
damaged, replace it.
6. Check for gas leaks on all connections.
7. Check and adjust gas pressure.
Gas
manifold
Gas inlet pressure
(pipeline)
pressure
(burner)
Gas burner pressure
adjustment
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable Timer
The programmable timer allows precise operating and timing control and is standard on this furnace. (Figure 10)
Overview
The programmable timer has the following features:
•
•
•
•
•
•
•
Long life lithium battery
Daily and weekly programs
One minute minimum switching time
Quick progression
Sixteen programs (8 on and 8 off)
Days of the week and hours of the day selection
Programmable day blocks:
1-2-3-4-5
1-2-3-4-5-6
(Monday – Friday)
(Monday – Saturday)
1-2-3-4-5-6-7 (Monday – Sunday)
6-7
(Saturday – Sunday)
Figure 10
KEY
A
On/Off Switch
Pos. I
The appliance is controlled by the room thermostat
Pos. AUTO The appliance is controlled by both the timer and the room thermostat
Pos. O
The appliance is turned off
B
Setting / Regulator Switch
Pos.
Time setting
Pos. RUN
Normal operating mode (the display shows the current time)
Pos. Ê
Setting of programming
C
D
E
F
Program Selection
Day Selection
Hours Setting
Minutes Setting
SKIP Button
G
R
Reset Button
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting and Adjustment
Initial Conditions
1 2 3 4 5 6 7
ꢀ
0:00
A.
Set the Setting/Regulator switch (Figure 10-B) in RUN position (center). Press the
Reset button R. The display will flash.
1 2 3 4 5 6 7
ꢀ
B.
With the Setting/Regulator switch selector in position (right), press the Reset button,
R, the display error EEE will appear. Move the Setting/Regulator switch, (Figure 10-B)
to the RUN (center) position. The display will disappear.
E EE
1 2 3 4 5 6 7
ꢀ
C.
D.
E.
If the Setting/Regulator switch, (Figure 10-B) is moved to position the display is
frozen.
0:00
1 2 3 4 5 6 7
If the Setting/Regulator switch, (Figure 10-B) is moved to RUN position the display is
frozen with the colon flashing.
ꢀ
0:00
If the Setting/Regulator switch, (Figure 10-B) is moved to position (right), the
1 2 3 4 5 6 7
display is flashing:
,1,1.
☼
ꢀ
☼
1
Manual Operation
0:00
Move the On/Off switch, (Figure 10-A) to the I position (left).
•
The symbol of a light ( ) will appear on the display. In this condition the heater is controlled by the furnace thermostat
☼
and is independent of the timer program.
Move the On/Off switch, (Figure 10-A) to the O position (right).
The symbol of the light (☼) on the display will disappear. In this condition the furnace is turned off.
•
Move the On/Off switch, (Figure 10-A) to the AUTO position (center).
•
The program function is activated. The furnace will operate according to the programs. The furnace is controlled both
by the timer and by the furnace thermostat.
1 2 3 4 5 6 7
ꢀ
Day and Time Setting
0:00
A. The Setting/Regulator switch, (Figure 10-B) is placed in the position (left).
B. To set the day of the week, press the Day Selector button, (1….7, Figure 10-D), a triangular
shaped indicator proceeds one day at a time. Number 1 stands for Monday, number 2
stands for Tuesday, etc.
1 2 3 4 5 6 7
ꢀ
15:16
C. To set the time press the Hour Selector button (h, Figure 10-E) to set the hour and the
Minutes Selector button (m, Figure 10-F) to set the minutes. The hours are set using military
time.
Example: Set
Wednesday, 15:16
hours (military time).
D. After setting the day and the time move the Setting/Regulator switch, B to the RUN position
(center). The display is frozen and the colon is flashing.
1 2 3 4 5 6 7
☼
Programming the Timer
1
0:00
Sixteen settings may be programmed on the timer. Eight odd numbers (1-3-5-7-9-11-13-15) for the
ON position and eight even numbers (2-4-6-8-10-12-14-16) for the OFF position. Program numbers
1 2 3 4 5 6 7
ꢀ
☼
1
are to the left of the symbol on the display.
☼
0:00
A. Move the Setting/Regulator switch, (Figure 10-B) to the position (right). On the right side
of the display the number 1, 1, will appear. The ON time may now be set.
☼
1 2 3 4 5 6 7
ꢀ
☼
1
B. Press the Day selection, (1…...7, Figure 10-D) button to the day or the block of days you
want the furnace to turn ON. Number 1 stands for Monday, etc. To set the desired time,
press the Hours Selection (h, Figure 10-E) button to set the hour and the Minute Selection
(m, Figure 10-F) button to set the minutes (for example 09:03). The time is set using military
time.
9:03
1 2 3 4 5 6 7
ꢀ
1
0:00
C. Press the Program Selection ( , Figure 10-C). The right side of the display will show a
number 2 without the light symbol. The OFF time may now be set.
1 2 3 4 5 6 7
ꢀ
1
11:04
17
Download from Www.Somanuals.com. All Manuals Search And Download.
D. Press the Day Setting, (1……7, Figure 11-D) button to program another day or block of days.
E. To set further programs repeat steps item B through D above.
NOTE: When the same ON and OFF times are desired for different days of the week, the setting procedure may be simplified.
•
•
•
•
1-2-3-4-5
1-2-3-4-5-6
(from Monday through Friday)
(from Monday through Saturday)
1-2-3-4-5-6-7 (from Monday through Sunday)
6-7 (Saturday and Sunday)
F. To avoid undesired operation verify that the programs do not overlap one another. You can check the settings by
pressing the Program Selection button. ( , Figure 10-C)
G. Move the Setting/Regulator switch to the RUN position (center). The display will show the current day and time.
IMPORTANT: All the programs set will be activated ONLY the day after the setting has been carried out.
During operation, the ON status of the timer is shown on the display with the symbol on the right end. When the symbol
☼
☼
does not appear, the timer is OFF.
Cancelling a Single Program
To cancel a single program:
A. Move the Setting/Regulator switch (Figure 10-B) to the ( , Figure 10-C) position (right).
Press the Program Selector ( , Figure 10-C) button and select the program to be
cancelled.
1 2 3 4 5 6 7
1
0:00
B. Simultaneously press the Program Selector ( , Figure 10-C) and SKIP button (
Figure 10-G) for at least 2 seconds. The selected program will be cancelled.
C. Verification that program has been cancelled is the continual blinking of 0:00.
Cancelling of all Preset Programs
To cancel all the preset programs, press the Reset button, R, for at least 2 seconds. All the preset programs will be cancelled.
Using the Skip Function
To skip a program:
1 2 3 4 5 6 7
ꢀ
A. Move the Setting/Regulator switch in the RUN position (center).
☼
1
B. Press the SKIP button (
Figure 10-G). The next program will be activated as
15:16
X
programmed. The SKIP symbol (
Figure 10-G) is shown on display.
C. The SKIP command may be stopped, by pressing the SKIP button. (
Figure 10-G)
1 2 3 4 5 6 7
ꢀ
The preset program will restart and SKIP symbol (
the display.
Figure 10-G) will disappear from
15:16
Skip Function Procedure During Operation
A. The SKIP function can be activated only in RUN mode.
B. The SKIP function starts immediately after the pressing the SKIP button, and disappears when next program starts.
C. The SKIP function can be stopped manually by pressing the SKIP button and the preset program will be activated.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Starting Sequence (Electrical)
Step 1
1. Check L1 – L2 (Supply 120 V, 60 Hz)
2. Check M9 (Main fuse)
Troubleshooting Step 1
Point 1 (L1-L2)
No voltage (120 V).
Check the electrical supply line, wiring and
connections.
Point 2 (M9)
Fuse damaged.
Check the electrical supply line and replace the
fuse.
Summer Mode
Step 2
3. Check Z1 (Reset summer/winter switch). The
switch is closed if there is no ignition block.
4. Check Z2 (Hi-Lo flame and fan speed switch)
Button down - Minimum velocity
Button up – Maximum velocity
Troubleshooting Step 2
Point 3 (Z1)
Z1 is open and no ignition.
Check wirings and connections. If everything is okay,
replace the switch.
Point 4 (Z2)
Z2 is down but the fan motor runs at the maximum
velocity (120 V).
Z2 is up but the fan motor runs at the minimum
velocity (<120 V).
Check wiring and connections. If they are okay,
replace the switch.
Winter Mode
Step 3
5. Check Z1 (Reset summer/winter
switch).
Button up – winter mode.
6. Check Z3 (Manual-automatic switch).
Button up – manual mode
Button down – automatic mode.
7. Check M2 (Fan thermostat).
The thermostat is closed only when its
temperature is higher than 104 °F.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Step 3
Point 5 (Z1)
Z1 is open and no ignition.
Check wiring and connections. If
everything is okay, replace the switch.
Point 7 (M2)
M2 is closed and fan thermostat
temperature lower than 104 °F.
Check wiring and connections. If they
are okay, replace the thermostat.
Step 4
8. Check Z9 (Room thermostat).
Close the thermostat with
clockwise rotation.
a
9. Check M1 (Overheat thermostat,
automatic reset). The thermostat is
closed at a temperture lower than
140 °F.
10. Check
motor).
S
(Combustion blower
Troubleshooting Step 4
Point 8 (Z9)
After a clockwise rotation, the contact is still
open. Check wiring and connections. If they are
okay, and the room temperature is cold, replace
the switch.
Point 9 (M1)
M1 is open and fan thermostat temperature is
lower than 140 °F. Check wiring, connections,
gas pressure and fan motor. Clean fan blades
and air grids. If everything is okay, replace the
thermostat.
Point 10 (S)
S motor does not run. Check voltage, wiring and
connections.
If everything is okay, replace the motor.
Step 5
11. Check NP (Pressure switch).
12. Check electrical supply to flame control box
(120 V)
24 V
120 V
13. Check TR (electrical transformer)
(120V/24V)
14. Check EV1 (Min gas valve, 24V)
15. Check RP7 (ignition electrode)
16. Check RP8 (flame sensor)
17. Check EV2 (Max gas valve, 24 V)
Troubleshooting Step 5
Point 11 (NP)
NP contact is open and air blower ON.
Check wiring and connections. Check and clean
blower pipes.
Check and clean burner and flue gas pipe.
Clean blower.
If everything is okay, replace the switch.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Point 13 (TR)
No inlet voltage (120 V).
Check 5 pole connector and control box.
If everything is okay, replace the connector.
No outlet voltage (24 V) during ignition.
Check wiring and connections.
If everything is okay, replace the transformer.
Point 14 (EV1)
Valve closed during ignition (Z2 down).
Check wiring, connections and voltage.
If everything is okay, replace the gas valve.
Point 15 (RP7)
No spark during ignition.
Check electrode, wiring and connections.
If everything is okay, replace the flame control box.
Point 16 (RP8)
No flame sensing.
Check flame sensor, wiring and connections.
…Check gas pressure and exhaust flue pipe.
If everything is okay, replace the flame control box.
Point 17 (EV2)
No voltage on EV2 with Z2 up.
Check wiring and connections.
If everything is okay, replace the switch.
Valve closed with voltage with Z2 up.
Check wiring, connections and voltage.
If everything is okay, replace the gas valve.
Starting Sequence (Gas)
1.
2.
3.
4.
5.
6.
7.
8.
Check and clean exhausted flue pipes;
Check and clean air blower and fan motor;
Check and clean burner and combustion chamber;
Check and clean gas nozzle;
Check gas type;
Check supply gas line pressure (see the manual);
Check gas losses;
Set burner gas pressure (see the manual).
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacement Parts
TR – 120/24V Transformer
Part Number: JTRS017
Part Number: JCNT019
Ignition Control Box
NP – Pressure Switch
Z9 – Room Thermostat
Part Number: JPRS009
Part Number: JTLT005
Z1 – Reset and Summer/Winter
Switch
Part Number: NTST000
Part Number: N19800202
Z8-Z3 – Timer and Manual-
Program Mode Switch
Z2- Hi-Lo Flame and
Fan Speed Switch
Part Number: N19800201
Electric Box
Part Number:
ELMP006 – ELMP007
SF/SB – Green and Red Lamps
Part Number:
E-PRG005
Z8 - Timer
Gas Assembly
Gas Burner and Gas Nozzle
Part Number: JPRT011
Natural Gas Nozzle
LP Gas Nozzle
Part Number: JGLL069
Part Number: JGLL062
EV1/2
Min/Max Gas Valve
Part Number: GVLV022
22
Download from Www.Somanuals.com. All Manuals Search And Download.
RP8 : Flame
Sensor
Part Number: JLTT015
RP7: Spark Igniter
(2 pieces)
Part Number: JLTT023
S – Combustion Blower Motor
Part Number: JMTR020
M1 – Overheat Thermostat
M2 - Fan Thermostat
Part Number: JTRM006
Part Number: J12301018
Fan Blades
(4 Pieces)
Part Number:
VVNT003-VVNT002
M - Fan Motor
(2 Pieces)
Part Number:
JMTR018
Williams Furnace Co., 250 West Laurel Street, Colton, CA 92324 U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|