INTRODUCTION
TABLE OF CONTENTS
OWNER’S MANUAL
Dear Whistler Owner,
Model Features Summary........................ 3 - 5
Installation............................................... 5 - 6
• Mounting Guidelines................................... 5 - 6
• Windshield Mounting.................................. 5 - 6
• Power Connection and Fuse Replacement..6
Operation................................................ 7 - 13
• Power On and Self-Test................................7
• Setting Saver.................................................7
• Feature Engaged Confirmation....................7
• Audio Level Adjustment..............................7
• Integrated Real Voice® (1773 only)...............7
• Auto Quiet Mode..........................................8
• Quiet Mode...................................................8
• City/City 1/ City 2 Mode............................8 - 9
• Highway Mode.............................................9
• Dim/Dark Mode.......................................... 9
• Engaging/Disengaging VG-2...................... 10
• Teach/Tutorial Mode....................................10
• Option Select Mode (1773 only)...................11
• Vehicle Battery Saver Mode.........................12
• Stay Alert Feature.........................................12
Safety Warning System™.......................... 13
POP™ Mode Alerts................................... 14
Laser/Radar Alerts................................... 14
• Speed Radar Audio/Visual Alerts...............14
• Laser Audio/Visual Alerts...........................14
If you have questions concerning the
operation of this Whistler product
please call:
With the change in time also comes change in technology.
Radar gun manufacturers have stepped up to the plate.
The new arsenal they carry is called POP™ Mode. This new
gun is a normal K or Ka band radar gun detectable by
most radar detectors made in the past 30 years, unless
the gun is placed in POP™ Mode. POP™ Mode is a feature
on some newer radar guns operating on K and Ka bands.
When the gun is in POP™ Mode and activated, a brief burst
of energy, less that 1/15 of a second, is transmitted and
the vehicle’s speed is quickly acquired. A detector without
POP™ Mode detection capability cannot respond to this
brief transmission. This detector has the power to report
this new gun where other detectors cannot! - until now!
Whistler introduces the 1758 and 1773 with POP™
Mode detection! These units are the beginning in total
protection. With POP™ Mode detection, these units can
react fast enough to detect this new technology. Packed
with power you still have a full featured radar detector:
CuSTOmer SeRVICE
1-800-531-0004
Monday - Friday • 8:00 am - 5:00 pm CT
1758/1773
or visit our website
www.whistlergroup.com
™
Total Band Protection
LASER-RADAR
DETECTOR
Please keep the receipt in a safe place.
You may register your product online
at www.whistlergroup.com. For warranty
verification purposes, a copy of your
dated store receipt must accompany any
unit sent in for warranty work. If the
unit is returned without a dated store
receipt, an out of warranty service charge
applies. Note: Your warranty period begins
at the time of purchase. The warranty is
validated only by the dated store receipt!
Now is the time to record the serial
number of the unit in the space provided
in the warranty section of the manual.
• NEW POP™ MODE CAPABILITIES
• HIGH GAIN OPTICAL LENS which provides
increased laser sensitivity.
®
• REAL VOICE ALERTS (1773 Only) are given
®
• Pulse Protection ...........................................14
verbally through the detector so you do not have
to take your eyes off the road to look at the display.
• SEVEN SEGMENT DISPLAY (1758 Only)
provides numeric signal strength indicator and
band identification.
VG-2 Alerts.............................................. 15
• Alert Priority.................................................15
Reset Features......................................... 16
Troubleshooting Guide............................ 17
Care and Maintenance.............................18
Are Detectors Legal?...............................18
FCC Information.......................................19
Speed Monitoring....................................19 - 22
• Radar Facts................................................... 20
Even though these units are packed full of features, they’re
still very easy to use. To fully utilize your unit to its potential,
we recommend reading this entire manual or visit our
FAQ page on our web site www.whistlergroup.com.
The Whistler Group Corporate Headquarters
13016 N. Walton Blvd. • Bentonville, AR 72712
Tel 479.273.6012 • Fax 479.273.2927
™
• POP Mode...................................................20
™
• Total Band Protection ................................. 20
Customer Return Center
Enjoy your new Whistler and please drive safely.
Sincerely,
• Laser Facts.................................................... 21
• Other Speed Detection Systems.................22
Warranty Information...............................23 - 25
Specifications...........................................25
Accessories.............................................. 26
1201 N. Dixieland Rd. • Rogers, AR 72756
Customer Service Tel 800.531.0004
www.whistlergroup.com
The Whistler Group, Inc.
P/N 203172
©
2004 The Whistler Group, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATION
OPERATION
Auto Quiet Mode
City/City 1/City 2 Mode (Cont.)
In City Mode, weak speed/safety radar signal give an
initial alarm of two beeps, and then remains quiet
unless the signal becomes very strong. When the
signal strength increases, two additional beeps are
provided.
Power On and Self-Test
Auto Quiet reduces the selected audio level to level
(1) approximately 5 seconds after a radar or safety
radar signal is detected. The alert for any new signal
within 20 seconds will resume at level (1). Auto Quiet
does not affect VG-2 or laser alerts.
Each time your Whistler detector is turned on, an
automatic self-test sequence confirms that the
speaker and visual displays are functional.
• Press Power. Display reads (1773 only) in order:
1. WHISTLER 2. X-band 3. K-band 4. Ka-band
6. SR ON 7. VG2 OFF 8. B SVR ON
10. HWY
• Display indicators will light in same order for 1758.
City 1 and CIty 2 Modes operate the same as Highway
Mode, but in City 1 Mode, only the X band sensitivity
is lowered. In City 2 Mode, X-band is not detected.
5. LASER
9. POP ON
• Press Quiet/Menu (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you may
cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Setting Saver
CAUTION: Some towns/small cities may still be using
X band radar. If Auto Quiet is engaged in City 1 or
City 2 modes and the unit receives a strong radar signal,
the unit performs the Auto Quiet feature. City Modes
do not change the audio alert for laser or VG-2.
Setting Saver saves your personalized settings so
that when the detector is turned off and then on
again, you do not have to re-enter them.
Quiet Mode
Feature Engaged Confirmation
Quiet cancels audio during an alert and any new alert
within 20 seconds. After 20 seconds, approximately
2 beeps are provided on any new alert and unit then
remains quiet.
Each time a button is pressed one beep confirms
feature “on”, two beeps confirm feature “off”.
Highway Mode
Highway mode provides full audio warnings any time
radar (X, K, Ka, Safety Radar) or laser signals are
detected, and is recommended for open road driving.
Audio Level Adjustment
The audio levels can be adjusted high to low or low
to high.
• Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to restore
the standard audio alert pattern; or turn the unit
off, then on.
For more information on City and Highway mode, please visit
our FAQ page on our website: www.whistlergroup.com
• Press Volume
• Press Volume
up to increase audio level.
down to decrease audio level.
Dim/Dark Mode
As audio level is adjusted, beeps are provided and
the display indicates volume level.
City/City 1/City 2 Mode
Dim/Dark Mode reduces the illumination of the display.
Whistler’s Three Stage City Mode is designed to reduce
the annoyance of automatic door openers, intrusion
alarms and other devices which share frequencies with police
radar. Generally X band is used for these devices.
•
Press and hold Power for 2 seconds to reduce
illumination to a Dim setting.
Pressing and holding the power button for 2 seconds
a second time engages Dark Mode. The display
illumination is further reduced.
®
Integrated Real Voice (1773 only)
When selected, Real Voice® will be used to articulate
the following:
•
1. Band Identification
2. Safety Warning System messages
3. Feature Selection
NOTE: In certain cases the voice message does not
replicate the text message.
• Press City to cancel Highway mode and engage City.
• Press City a second time engages City 1.
• Press City a third time engages City 2.
• Pressing City a fourth time cancels City Modes and
returns the unit to Highway Mode.
Dim or dark can be engaged during an alert. In Dark
Mode, the display goes dark for as long as a signal is
being detected and for 20 seconds after, then the
display returns to the dimmer setting.
•
Pressing and holding the power button a third
time restores full illumination to the display.
7
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
OPERATION
OPERATION
OPERATION
Engaging/Disengaging VG-2
Vehicle Battery Saver Mode
Stay Alert Feature (Cont.)
Option Select Mode (1773 Only)
The Vehicle Battery Saver Mode automatically shuts off
your detector within 3 hours if you forget to turn it off. The
timer is reset if the detector is turned off, unplugged or any
button is pressed before the 3 hours have expired. The detector
will alert you with an audible and visual warning before
it shuts off.
During this warning you can reset the unit by pressing
any button. This will reset the timer.
If the unit has automatically turned itself off, press the Power
button to turn the unit back on. You can manually engage
the Vehicle Battery Saver Mode by pressing and holding
the City button until one beep is heard.
Entering Option Select Mode allows you to customize options
such as Tone Select, Abbreviated Power Up Sequence and
WARNING!!! Stay Alert is NOT intended as a substitute
for adequate rest. You should NOT operate a vehicle if you
are drowsy. During extended periods of vehicle operation,
you should take frequent breaks. Improper reliance on the
Stay Alert feature may result in vehicle damage, personal
injury or death. NEVER OPERATE A VEHICLE IF YOU
ARE DROWSY.
1773: See option select mode to turn this feature on.
VG-2 Mode. When selecting options, the
,
or quiet
1758: Press and hold the quiet button. Unit beeps
once for VG-2 on, twice for off.
must be pressed within 20 seconds or options mode will
automatically be exited. To enter:
When a VG-2 signal is detected, the VG-2 alert is
sounded. After 3 seconds the audio is cancelled and
the VG-2 indicator flashes at a slower rate. This cycle
is repeated if the VG-2 signal is again detected.
During the period a VG-2 signal is detected, a radar
signal cannot be detected. However, because the VG-2
alert has confirmed that a patrol car is nearby, you are
already aware of the potential for speed monitoring
and can adjust your speed accordingly. Laser detection
is not affected while a VG-2 signal is detected.
1773 Chart
™
Press:
Quiet
Display
Reads:
To Change: Option:
SWS
Safety Warning System™
1st Time
TONE 3
= YES
= NO
Tone 1, 2, 3
(3 different X, K, Ka
Patterns)
In communities where transmitters are located,
the Safety Warning System™ displays over 60 text
messages. When Safety Radar is detected the audio
alert is geiger counter-like.
Refer to “Option Select Mode” for instructions for
deactivating battery saver mode feature. (1773 Only)
2nd Time TEST YES
= ON
X, K, Ka Audio tones
= OFF 1 beep during
Power Up
Stay Alert Feature
The Stay Alert Feature is designed to test a driver’s
alertness. To engage (when unit is not alarming) :
Safety Warning System Text (1773 Only)
Teach/Tutorial Mode
3rd Time
4th Time
5th Time
6th Time
7th Time
VG-2 OFF
SR ON
= ON
Turns VG-2 On
Example: Poor - Road - Surface.
Provides simulated alerts for each type of signal.
= OFF Turns VG-2 Off
• Press and hold City for approximately 2 seconds.
Release button during or immediately after the alert
is given.
• 1758 Model displays a
message has been received.
to indicate a SWS™
• Press City and Quiet simultaneously and release.
• Press Power to exit.
= ON Turns Safety Radar
= OFF On
—1773 only: Display reads:
NOTE:
VOICE ON
POP ON
B SVR ON
= ON
Real Voice Engaged
Not all areas have Safety Warning System™ transmitters.
Within 30-60 seconds two beeps are sounded; to
show alertness, the driver must press either the City,
Volume, or Quiet buttons within 3-5 seconds. If a button
is pressed within 3-5 seconds, the cycle is repeated.
If a button was not pressed within 3-5 seconds alarm
sounds and the display reads:
= OFF Real Voice
= ON
POP On
= OFF POP Off
= ON
Battery Saver On
= OFF Battery Saver Off
—1758 only: The “H” or “C” will flash indicating
Stay Alert is activated.
Within 30-60 seconds two beeps are sounded; to
show alertness, the driver must press either the
Volume, City or Quiet button within 3-5 seconds.
If the button is pressed within 3-5 seconds, the cycle is
repeated. If a button was not pressed within 3-5 seconds,
alarm sounds and the display will flash all LED’s.
• Press Power to exit for both the 1758 & 1773.
10
11
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
™
RESET FEATURES
POP MODE ALERTS
VG-2 ALERTS
Reset Features
POP™ Mode Alerts
VG-2 Audio/Visual Alerts
All user features can be reset to factory settings.
Because POP™ Mode travels on regular radar bandwidth,
there is no particular alert for POP™ Mode transmissions.
POP™ Mode alerts will be displayed as a regular radar alert.
NOTE: You must turn this feature on before it will
detect VG-2.
When a VG-2 signal is detected, the detector ‘hides’ its own
radiated signal and becomes undetectable by the VG-2.
Every 30 seconds, the detector checks for a VG-2 signal.
If a VG-2 signal is still present, the unit continues to
hide and repeats the VG-2 alert. If no signal is detected,
two beeps are provided, indicating an ‘all clear’ condition.
During VG-2 Alert X, K, and Ka band signals cannot
be received (Reference page 19 for VG-2 information).
• Unplug Power Cord from unit.
• Press and hold Power and Quiet.
• Plug Power Cord into unit.
• Wait for 2 beeps.
• Release Power and Quiet buttons.
Unit is now reset.
Default factory settings are:
1. Audio to level (4).
LASER/RADAR ALERTS
2. Display reads Highway. (1773 only)
’H’ illuminates on 1758
3. Dim/Dark Mode to full illumination of display.
4. Auto Quiet Mode OFF.
5. VG-2 Detection Mode OFF.
6. Safety ON.
7. Vehicle Battery Saver ON.
8. Full Power Up sequence.
9. Default TONE 3.
Speed Radar Audio/Visual Alerts
When X, K or Ka is detected, the band ID and signal
strength is displayed. The audio alert is continuous
and has a geiger counter-like pattern. The faster the
beep the closer or stronger the radar source.
Alert Priority
When two or more signals are received at the same
time, the alert priority is:
1. Laser
2. VG-2
Laser Audio/Visual Alerts
3. Speed Radar
4. Safety Radar
When a laser signal is detected the audio alert is continuous
for a minimum of 3 seconds.
Example:
10. POP ON
11. Voice On (1773 only)
12. Unit ON or OFF.
• Model 1773 displays:
The more “|||” the closer the laser source.
If X band is alerting, then suddenly VG-2 is detected,
the VG-2 warning will override the X band alert.
• Model 1758 displays:
®
Pulse Protection
Pulse (or instant-on) radar is more difficult to detect
than conventional radar because it remains ‘off’ until
activated to measure the speed of a targeted vehicle.
When a pulse type transmission is detected, your Whistler
detector sounds an urgent 3-second audio warning
and the display shows:
After the 3-second pulse alert, the standard alert pattern
continues for as long as the signal is present.
It is important to respond promptly to a pulse alert,
since warning time may be minimal.
15
16
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
CARE AND MAINTENANCE
FCC INFORMATION
SPEED MONITORING
Your Whistler detector is expertly engineered and
designed to exacting quality standards to provide
you with reliable, trouble-free operation. If your unit
has been correctly installed following the guidelines
in this manual, but is not operating optimally, please
refer to the troubleshooting guide below.
FCC ID HSXWH11 - 1758, 1773
Care And Maintenance
Radar Facts
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device many not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
During the summer months, avoid prolonged exposure
to direct sunlight by removing your unit from the dash
when your vehicle is parked for an extended period of
time. Do not spray water, cleaners, or polishes directly
onto the unit. The spray may penetrate through the
openings and damage the unit. Also, do not use any
abrasive cleaners on the unit’s exterior.
A radar gun operates by transmitting radio waves at
certain frequencies which reflect off objects and are
then picked up by the radar gun’s receiving section.
When a radar beam reflects off a moving target, a
measurable frequency shift occurs. The radar unit converts
this shift into miles per hour to determine your vehicle’s
speed. Currently, the FCC (Federal Communications
Commission) permits operation of traffic radar guns
at X Band (10.500 - 10.550 GHz), K Band (24.050 -
24.250 GHz), and Ka Band (33.400 - 36.000 GHz).
PROBLEM: No display or audio.
IMPORTANT
•
Check fuse in Whistler plug; replace if necessary with a 2
amp 3AG type.
FCC requirements state that changes or modifications
not expressly approved by Whistler could void the
user’s authority to operate the equipment.
•
•
Check fuse for lighter socket; replace if necessary.
Make sure lighter socket is clean.
ARE DETECTORS LEGAL?
PROBLEM: Unit alarms when vehicle hits bumps.
Note: A radar detector will not alarm if an officer is
not transmitting on any one of the above radar bands.
•
•
Check for loose lighter socket; tighten and clean.
Check connections at both ends of power cord. Substitute
another cord to determine if cord is defective. Return
defective cord to the factory.
In Most States YES!
SPEED MONITORING
Laser-Radar detectors are legal in every state (with
the exception of Virginia and Washington, D.C., which
have local regulations restricting the use of radar
receivers in any vehicle) when used in automobiles or
light trucks (under 10,000 lbs.).
Radar Detector Detectors (VG-2)
POP™ Mode
PROBLEM: Unit alarms when using vehicle electrical
accessories (brakes, power mirrors, power
windows, turn signals, horn, etc.).
POP™ Mode is a feature on some newer radar guns
operating on K and Ka bands. When the gun is in
POP™ Mode and activated, a brief burst of energy,
less that 1/15 of a second, is transmitted and the
vehicle’s speed is quickly acquired. A detector without
POP™ Mode detection capability cannot respond to
this brief transmission. This detector has the power
to report this new gun where other detectors cannot!
The Interceptor VG-2, or simply VG-2, is a microwave
receiver used by police to detect signals radiated by
the local oscillator of a radar detector. Because its
purpose is to identify persons driving with radar detectors,
the VG-2 is known as a ‘radar detector detector’.
Concerning trucks over 10,000 lbs., the Federal
Highway Administration (FHWA) issued a regulation,
effective January, 1994 which prohibits radar and laser
detector use in these types of vehicles nationally. Prior
to the FHWA regulation, laws existed in the state of
New York restricting the use of radar detectors in trucks
over 18,000 lbs. and in Illinois in trucks over 26,000 lbs.
•
Vehicle’s electrical system, including battery and alternator, may
have electrical noise. Install a filter capacitor (470mfd. 25 volt
or larger capacitance value) on the back of the lighter socket.
The VG-2 is the primary tool used by the police to
identify radar detector equipped vehicles. If caught,
in a state where detectors are illegal, (see page 18),
drivers risk losing their radar detector and receiving a
fine. In addition, instant-on radar is almost always used
in combination with a VG-2, leaving unsuspecting motorists
vulnerable to receiving two tickets - one potentially
for speeding, the other for possession of a detector.
PROBLEM: Unit gives laser alert when accelerating.
•
Possible bad or low quality distributor cap. Replace with
high quality cap.
Total Band Protection™
PROBLEM: Audio alerts are not loud enough.
Complete Band Coverage that detects laser, radar,
VG-2 and safety radar bands.
•
•
Cancel Auto Quiet Mode or City Mode.
Check audio level setting (see page 7 & 8).
If difficulties occur which cannot be solved by information
in this Troubleshooting Guide, please call Whistler
Customer Service at 1-800-531-0004 or visit our FAQ
page at www.whistlergroup.com/faq-detectors.asp,
before returning your unit for service.
Having a radar detector capable of detecting the
VG-2 may alert you to the presence of a speed trap. For
more information on speed monitoring technologies,
please visit our FAQ page on our website:
www.whistlergroup.com
NOTE: It is the responsibility of the individual radar
detector owner to know and understand the laws in your
area regarding the legality of the use of radar detectors.
17
18
19
20
Download from Www.Somanuals.com. All Manuals Search And Download.
SPEED MONITORING
Laser Facts
SPEED MONITORING
Laser Tips
WARRANTY INFORMATION
Service Under Warranty
If you are the targeted vehicle, a laser gun can often
determine your speed within a few seconds after you
receive an alert. In this situation there is generally no
time to safely adjust your speed. However, if you are
traveling near or behind the targeted vehicle and
receive an alert, response time should be sufficient.
Any laser alert, regardless of duration, requires
immediate action!
During the warranty period, defective units will be
repaired without charge to the purchaser when returned
with a dated store receipt to the address below. Units
returned without dated store receipt will be handled
as described in section “Service Out Of Warranty.”
Due to the specialized equipment necessary for testing
a Laser-Radar receiver, there are no authorized service
stations for Whistler brand detectors other than Whistler.
It’s well documented that many radar guns cannot
reliably provide the speed of a targeted vehicle that
is traveling in a group of vehicles. In contrast, a laser
gun can target a specific vehicle out of a line of traffic
and determine its speed. The advantage of laser
over radar in terms of target identification is the result
of the laser gun’s narrow beam. A radar transmission
can cover more than a four-lane highway at a distance
of 1,000 feet, compared with a laser transmission
which covers about 3 feet at the same distance. For
best protection, keep these points in mind:
Other Speed Detection Systems
When returning a unit for service under warranty,
please follow these instructions:
Several techniques other than radar or laser are used
to measure vehicle speeds. When these methods
are being used, no detector can provide a warning.
These techniques include:
1. Ship the unit in the original carton or in a suitable
sturdy equivalent, fully insured, with return
receipt requested to:
• Because you vehicle’s license plate or headlights
are the laser gun’s primary targets, mounting your
Whistler detector on the dashboard can improve
laser detection at short range.
• Do not follow closely behind any vehicle you cannot
see through. If you can’t see past a vehicle ahead
of you, chances are your detector won’t either.
• The receiving range of your laser detector will not
be the same as a radar detector. Laser guns are
most often used at short range.
• Pacing - A patrol car drives behind you and matches
your driving speed.
• Vascar/Aircraft - The time it takes a vehicle to travel
a known distance is measured.
Whistler Repair Dept.
1201 North Dixieland Rd
Rogers, AR. 72756
Please allow 3 weeks turnaround time.
WARRANTY INFORMATION
IMPORTANT: Whistler will not assume responsibility
for loss or damage incurred in shipping. Therefore,
please ship your unit insured with return receipt
requested. CODs will not be accepted!
Consumer Warranty
Whistler Laser-Radar detectors receive all current laser
guns which operate at a laser wavelength of 905 +/- 10mm.
This Whistler Laser-Radar detector is warranted to the
original purchaser for a period of one year from the date
of original purchase against all defects in materials and
workmanship. This limited warranty is void if the unit is
abused, modified, installed improperly, if the housing has
been removed, or if the serial number is missing. There are
noexpresswarranties covering this product other than
those set forth in this warranty. All express or implied
warranties for this product are limited to the above time.
Whistler is not liable for damages arising from the use,
misuse, or operation of this product.
•Pro Laser™ I II III
•LT1 20-20
•Ultra Lyte
2. Include with your unit the following information,
clearly printed:
• Your name and street address (for shipping via
UPS), a daytime telephone number and email
address, if applicable.
• A detailed description of the problem (e.g., “Unit
performs self-test but does not respond to radar”).
• A copy of your dated store receipt or bill of sale.
23
21
22
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
WARRANTY INFORMATION
ACCESSORIES
3. Be certain your unit is returned with its serial number.
For reference, please write your unit’s serial number
in the following space: s/n_______________.
IMPORTANT: When returning your unit for service,
be certain to include a daytime telephone number,
and email address (if applicable).
These and other accessories can be ordered directly
from Whistler by calling 1-800-531-0004 or visit our
online store at www.whistlergroup.com
Customer Service
Units without serial numbers are not covered under warranty.
Order
Code
Description
Price
If you have questions concerning the operation of your
Whistler detector, or require service during or after
the warranty period, please call Customer Service at:
1-800-531-0004
IMPORTANT: To validate that your unit is within
the warranty period, make sure you keep a copy
of your dated store receipt. You may register
however, for warranty verification purposes, a
copy of your dated store receipt must accompany
any unit sent in for warranty work.
202151
206552
206553
206880
Windshield Bracket Kit
Straight Power Cord (5’)
Coiled Power Cord (7’)
$
9.95
Representatives are available to answer your questions
Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT) or
visit the FAQ’s at www.whistlergroup.com.
$ 14.95
$ 15.95
Hardwire Kit (10' )
$
9.95
(for wiring to fuse box)
Service Out of Warranty
Units will be repaired at ‘out of warranty’ service
rates when:
206666
Modular Cord Package
(includes coiled and straight cords,
and power adapter)
$ 17.95
SPECIFICATIONS
• The units original warranty has expired.
• Dated store receipt is not supplied.
• The unit has been returned without its serial number.
• The unit has been abused, modified, installed
improperly, or had its housing removed.
159032
402081
206660
Package of 8 Suction Cups
Non-Skid Dash Pad
Straight Modular Cord and
Socket Multiplier
Coiled Modular Cord and
Socket Multiplier
$
$
2.95
6.95
Dimensions: 4.65” L x 2.95” W x 1.45” H
Weight: 6.8 oz.
Laser Wavelength: 905 50 nanometers (nm)
$ 11.95
The minimum out of warranty service fee for your
Whistler detector is $55.00 (U.S.). If you require out
of warranty service, please return your unit as outlined
in the section “Service Under Warranty” along with a
certified check or money order for $55.00. Payment
may also be made by MasterCard, VISA or American
Express; personal checks are not accepted.
In the event repairs cannot be covered by the minimum
$55.00 service fee, you will be contacted by a Whistler
technical service specialist who will outline options
available to you. If you elect not to have your unit
repaired, it will be returned to you along with your
certified check or money order.
Radar Frequencies:
206661
$ 12.95
10.500 - 10.550 GHz (X Band)
24.050 - 24.250 GHz (K Band )
33.400 - 36.000 GHz (Ka Superwideband)
Operating Temperature Range: -20˚ C to +80˚ C
*Modular: Interconnecting pieces cord and plug. Shipping and
handling (per order) $5.00 Prices are subject to change without notice.
(-4˚ F to +176˚ F)
Power Requirements:
Operational 12 to 15 volts DC, 250mA nominal
Vehicle Battery Saver, 30mA nominal.
One or more U.S. patents may apply:
#5,146,227, #5,379,456, #5,666,120, #5,990,821
POP™ Mode is a trademark of MPH Industries, Inc.
Specifications are subject to change without notice.
24
25
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|