®
ELECTRIC AND GAS
DRYERS
Use & Car e Gu ide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-253-1301
or visit our website at
Table of Contents..........................................................................2
8528324
Download from Www.Somanuals.com. All Manuals Search And Download.
DRYER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or
“WARNING.” These words mean:
You can be killed or seriously injured if you don't
immediately follow instructions.
You can be killed or seriously injured if you don't
follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you
what can happen if the instructions are not followed.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
•
•
•
•
instructions.
If you cannot reach your gas supplier, call the fire department.
•
– Installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic
precautions, including the following:
■
■
Read all instructions before using the dryer.
■
Do not repair or replace any part of the dryer or
attempt any servicing unless specifically recom-
mended in this Use and Care Guide or in published
user-repair instructions that you understand and have
the skills to carry out.
Do not place items exposed to cooking oils in
your dryer. Items contaminated with cooking oils
may contribute to a chemical reaction that could
cause a load to catch fire.
■
■
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
■
Do not dry articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry-cleaning solvents, other flammable,
or explosive substances as they give off vapors
that could ignite or explode.
■
■
Do not allow children to play on or in the dryer.
Close supervision of children is necessary when
the dryer is used near children.
■
■
Clean lint screen before or after each load.
Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
Before the dryer is removed from service or dis-
carded, remove the door to the drying compart-
ment.
Do not reach into the dryer if the drum is moving.
Do not install or store the dryer where it will be
exposed to the weather.
■
■
■
■
See Installation Instructions for grounding require-
ments.
■
Do not tamper with controls.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND FEATURES
1.
4.
5.
2.
3.
6.
1. Control panel
Additional features your dryer may
have
Large side-swing door
Super wide-swing door
2. Model and serial number label
3. Dryer drum
End of Cycle Signal selector
WRINKLE SHIELD™ selector
WRINKLE SHIELD™ PLUS selector
ACCUDRY™ electronic sensor
Automatic Dry sensor
4. Lint screen
5. Exhaust grille
6. Wide-opening door
Drum light
Small side-swing door
Optional purchase
Drying rack
Control Panel
NOTE: The drawings in this book may vary from your dryer. They are designed to show all of the models covered by this book. Your
dryer may not include all features.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The exhaust vent can be routed up, down, left, right, or
straight out the back of the dryer. Space requirements are
listed in your Installation Instructions.
CHECKING
YOUR VENT
Your dryer must be properly installed and vented to achieve
maximum drying efficiency and shorten drying times. Use the
minimum recommended installation clearances (found in your
Installation Instructions) to avoid blocking the flow of combustion
and ventilation air. Refer to your Installation Instructions for more
information.
4. Use the straightest path possible when routing the exhaust
vent. Use the fewest number of elbows and turns. Allow room
when using elbows or making turns. Bend vent gradually to
avoid kinking.
Fire Hazard
Use a heavy metal vent.
5. Use duct tape to seal all joints. Do not use screws to secure
vent. Lint may catch on screws.
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in
death or fire.
If the dryer is not properly installed and vented, it will not be
covered under the warranty.
6. Clean exhaust vent periodically, depending on use, but at
least every 2 years, or when installing your dryer in a new
location.
NOTE: Service calls caused by improper venting will be paid for
by the customer, whether it was a paid installation or self-
installed.
■
Disconnect vent from the dryer and clean one section at a
time until you reach the exhaust hood.
1. Do not use plastic vent or metal foil vent. Use 4 in. (10.2 cm)
metal or flexible metal vent. Do not kink or crush flexible
metal vent. It must be completely extended to allow adequate
exhaust air to flow. Check vent after installation. Refer to your
Installation Instructions for proper length requirements of
vent.
■
To clean out lint, use the hose attachment on your
vacuum, or a pole or wire with a feather duster or rag
attached.
■
■
Be sure the flapper on the outside end of vent moves
freely.
When cleaning is complete, be sure to follow the
Installation Instructions supplied with your dryer for final
product check.
2. Use a 4 in. (10.2 cm) exhaust hood. Smaller hoods increase
drying times.
2
1
4"
(10.2 cm)
4"
(10.2 cm)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Startin g Your Dryer
DRYER USE
Before using your dryer, wipe the dryer drum with a damp cloth to
remove dust from storing and shipping.
1. Load clothes loosely into the dryer and close the door. Do not
pack the dryer. Allow space for clothes to tumble freely.
Explosion Hazard
2. Turn the Cycle Control knob to the recommended cycle for
Keep flammable materials and vapors, such as
gasoline, away from dryer.
the type of load being dried. Use the Energy Preferred
Automatic Setting ( ) to dry most heavyweight and medium
*
weight loads. See “Drying, Cycle, and Temperature Tips.”
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in
death, explosion, or fire.
3. Select a temperature setting on models with a Temp/Fabric
selector. The cycle descriptions include temperature setting
suggestions.
NOTE: The temperature selector is part of the Cycle Contol
knob on some models.
4. Select the End of Cycle Signal, if available. The signal is
helpful when drying permanent press or synthetics. Promptly
remove these items from the dryer at the end of the cycle to
prevent wrinkles.
Fire Hazard
No washer can completely remove oil.
On some models
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
■
The End of Cycle Signal can be adjusted. Turn the
selector to the desired volume.
Items containing foam, rubber, or plastic must be
dried on a clothesline or by using an Air Cycle.
OR
■
The End of Cycle Signal is part of the START button. Turn
the START button to ON or OFF.
Failure to follow these instructions can result in
death or fire.
5. Select the desired option. See “Additional Features.”
6. Push the START button.
Stoppin g and Restar tin g
You can stop your dryer any time during a cycle.
To stop your dryer
Open the dryer door or turn the Cycle Control knob to OFF.
NOTE: The Cycle Control knob should point to an Off area when
the dryer is not in use.
To restart your dryer
1. Close the door.
2. Select a new cycle and temperature (if desired).
3. Push START.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Loadin g Cloth es
Cycle Descriptions
Load clothes loosely into the dryer. Do not pack the dryer. Allow
space for clothes to tumble freely. The following chart shows
examples of balanced loads that would allow for proper tumbling.
This manual covers several different models. Your dryer may vary
from the model shown and may not have all of the cycles and
features described.
Heavy work
clothes
3 pair of pants, 4 pair of jeans, 2 pair of
overalls, 3 shirts
Delicates
3 camisoles, 1 robe, 4 slips,
6 undergarments, 2 sets of sleepwear,
1 child’s outfit
Towels
10 bath towels, 10 hand towels, 14 wash
cloths, 1 bath mat
Mixed Load
3 double sheets, 4 pillowcases,
8 T-shirts, 6 pair of shorts, 2 blouses,
8 handkerchiefs
Cycle Control knob
Drying, Cycle, an d Tem per atu r e Tips
Automatic cycle(s)
Select the correct cycle and temperature for your load.
Use your Automatic cycle to dry most loads. Your dryer uses
either the electronic ACCUDRY™ system or the Automatic Dry
control. The control senses the moisture level in the load and
shuts off when the load reaches the selected dryness.
Cool Down tumbles the load without heat during the last few
minutes of all cycles to make the load easier to handle.
Drying tips
■
Follow care label directions when they are available.
On some models
■
If you use fabric softener sheets, use only those labeled
“dryer safe.” Follow package instructions.
■
Automatic Dry (High Heat) and Automatic Dry (Low Heat)
Select the temperature by moving the Cycle Control knob to
(High Heat) for bigger or heavier loads or (Low Heat) for
smaller or lighter loads.
■
Remove the load from the dryer as soon as tumbling stops, to
reduce wrinkling. This is especially important for permanent
press, knits, and synthetic fabrics.
■
■
Automatic Dry
Cycle and temperature tips
Select the temperature from the temperature selector based
on the fabrics in your load.
■
■
■
Dry most loads using the Energy Preferred Automatic
Setting ( ), if available on your dryer.
*
ACCUDRY™ System
Use a High Heat setting for drying heavyweight items such as
towels and work clothes.
Select the temperature from the temperature selector based
on the fabrics in your load.
Use a Medium Heat setting for drying medium weight items,
such as sheets, underwear, permanent press fabrics, and
some knits.
After drying a load in any of the Automatic cycles, check the
dryness.
■
■
■
Use a Low Heat setting for drying lightweight items such as
lingerie, blouses, dresses, and some knits.
■
If the load is drier than you like, select a setting closer to Less
Dry the next time you dry a similar load.
Use a no-heat (air) setting for foam, rubber, plastic, or heat-
sensitive fabrics.
■
If a load is not as dry as you like, complete drying using a
Timed cycle. Select a setting closer to Very Dry the next time
you dry a similar load.
Line dry bonded or laminated fabrics.
NOTE: Drying time varies with an Automatic cycle. The type of
fabric, size of the load, and the dryness selected affect drying
time. See “Drying, Cycle and Temperature Tips.”
NOTE: If you have questions about drying temperatures for
various loads, refer to the care label directions. If you are unsure
of the temperature to select for a load, select a lower setting
rather than a higher setting.
Timed Drying cycle(s)
Use Timed Drying for heavyweight and bulky items, such as
bedspreads and work clothes or large loads that require a long
drying time. Set the temperature selector, if available, to High
Heat.
On some models, you may use the Timed Drying cycle for
lightweight items such as lingerie or knits. Set the temperature
selector, if available, based on the fabrics in your load.
NOTE: Use your Timed Drying cycle to complete drying if items
are still damp after the Automatic cycle.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Your dryer may have one of the following features:
Fluff Air cycle or Air Only setting
Use the Fluff Air cycle, or Air Only setting, for items that require
drying without heat such as foam, rubber, plastic and heat
sensitive fabrics. Set the Cycle Control knob to Fluff Air or select
Air Only on the Temperature selector and set the Cycle Control
knob to Timed Drying. This chart shows examples of items that
can be dried using the Fluff Air cycle/Air Only setting.
■
WRINKLE SHIELD (automatic)
The WRINKLE SHIELD feature automatically activates at the
end of the cycle if you do not open the dryer door within a few
minutes. The WRINKLE SHIELD feature periodically tumbles
the load without heat for up to 45 minutes.
■
■
WRINKLE SHIELD (optional)
Turn the WRINKLE SHIELD feature selector to On to
periodically tumble the load without heat up to 45 minutes
after the cycle ends.
Type of Load
Fluff Air cycle/
Air Only setting*
Foam rubber - pillows, padded bras,
stuffed toys
WRINKLE SHIELD™ Plus 30/90 Minute
The WRINKLE SHIELD Plus feature selector lets you choose
30 or 90 minutes of periodic unheated tumble after the cycle
ends.
20 - 30
20 - 30
40 - 50
10 - 20
Plastic - Shower curtains, tablecloths
Rubber-backed rugs
Olefin, polypropylene, sheer nylon
Heavy Dry
Select this setting to evenly dry large or heavy items such as
thick cotton bath towels or robes. Set the Temperature selector, if
available, to High Heat.
*(Minutes). Reset cycle to complete drying, if needed.
When using Fluff Air or Air Only
DRYEL® fabric care system
■
■
■
Check to see that coverings are securely stitched.
Shake and fluff pillows by hand periodically during cycle.
Dry item completely. Foam rubber pillows are slow to dry.
When using DRYEL fabric care, select the DRYEL cycle setting
and the DRYEL temperature setting. DRYEL fabric care, when
used in accordance with the manufacturer’s directions, has been
tested and approved for use in full-size dryers built by Whirlpool
Corporation.
Addition al Featu r es
Damp Dry
This manual covers several different models. Your dryer may not
have all of the features described.
Select this setting to dry items to a damp level, or to dry items
that do not require an entire drying cycle. Damp dry items such
as jeans (to prevent stiffness) or cotton clothing (to make
pressing easier). Set the temperature selector, if available, to High
Heat.
Towels
Select this setting to thoroughly dry extra heavy items such as
mattress pads and quilts or a load of towels. Set the temperature
selector, if available, to High Heat.
TUMBLE PRESS® setting
Select this setting to remove wrinkles from items such as clothing
packed in a suitcase or items wrinkled from being left in the dryer
too long. Set the temperature selector, if available, to Medium or
Low Heat depending on the fabrics in your load.
Casual
Select this cycle to dry medium to lightweight synthetic,
permanent press or no-iron items such as, sheets, shirts or
dresses. Set temperature selector, if available, to Medium.
End of Cycle Signal
Delicates
If your model has an End of Cycle Signal, the signal sounds
when a cycle is complete. If the WRINKLE SHIELD™ feature is
on, the signal sounds every few minutes. The signal stops when
you open the door or turn the Cycle Control knob to Off.
Select this option to dry small loads or lightweight items. Set the
temperature selector, if available, to Low or Extra Low Heat.
WRINKLE SHIELD™ feature
When you are unable to remove a load from the dryer as soon as
it stops, wrinkles can form. The WRINKLE SHIELD feature
periodically tumbles, rearranges and fluffs the load without heat
to avoid wrinkles. A signal will sound periodically when the
WRINKLE SHIELD feature is on, if the End of Cycle Signal is
selected. The signal and the tumbling will end when you open the
dryer door or turn the Cycle Control knob to Off.
On some models
■
The End of Cycle Signal is fixed.
OR
■
The End of Cycle Signal is selectable. The signal will sound
only if the signal is set to On.
Your model may vary from the model shown.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Drying Rack
DRYER CARE
The drying rack is useful for machine drying items you would not
necessarily want to tumble dry or that you would normally line dry
(for example, tennis shoes, pillows, stuffed toys).
Cleanin g th e Lin t Screen
If your model does not have a drying rack, you may purchase
one. For ordering information, please refer to the “Assistance or
Service” page of this manual. You may also contact the dealer
from whom you purchased your dryer.
Every load cleaning
The lint screen is located on the top of the dryer. Clean it before
each load. A screen blocked by lint can increase drying time.
To use the drying rack
To clean
1. Slide rear pegs into the dimples on the back wall of the dryer.
1. Pull the lint screen towards you. Roll lint off the screen with
your fingers. Do not rinse or wash screen to remove lint. Wet
lint is hard to remove.
Lower the front legs to rest on the dryer opening.
2. Put the wet items on top of the rack. Leave space between
the items so air can reach all the surfaces. Close the door.
NOTE: Do not allow items to hang over the edge of the rack.
2. Push the lint screen firmly back into place.
3. Select a timed drying cycle and temperature, or an air cycle.
Items containing foam, rubber, or plastic must be dried on a
clothesline or by using an air cycle.
IMPORTANT:
■
Do not run the dryer with the lint screen loose, damaged,
blocked, or missing. Doing so can cause overheating and
damage to both the dryer and fabrics.
4. Push the START button.
NOTE: The rack must be removed for normal tumbling. Do not
use the automatic cycle with the drying rack.
■
Some towels made of synthetic fibers and natural fibers
(polyester and cotton blends) may shed more lint than other
towels, causing your dryer’s lint screen to fill up faster. Be
sure to remove lint from the lint screen before and after drying
new towels.
This chart shows examples of items that can be rack-dried and
the suggested cycle, temperature setting, and drying time. Actual
drying time will depend on the amount of moisture items hold.
Rack Dry
Cycle
Temp
Time*
■
If lint falls off the screen into the dryer during removal, check
the exhaust hood and remove the lint. See “Checking Your
Vent.”
Wool Sweaters
Timed
Low
60
Block to shape and lay flat on
the rack
As needed cleaning
Laundry detergent and fabric softener residue can build up on the
lint screen. This buildup can cause longer drying times for your
clothes, or cause the dryer to stop before your load is completely
dry. The screen is probably clogged if lint falls off the screen.
Stuffed toys or pillows
Timed
Low
None
None
60
90
90
Cotton or polyester fiber filled
Clean the lint screen with a nylon brush every six months or more
frequently if it becomes clogged due to a residue buildup.
Stuffed toys or pillows
Air
Foam rubber filled
(no heat)
To wash
Sneakers or canvas shoes
Air
1. Wet both sides of lint screen with hot water.
(no heat)
2. Wet a nylon brush with hot water and liquid detergent. Scrub
lint screen with the brush to remove residue buildup.
*(Minutes). Reset cycle to complete drying, if needed.
3. Rinse screen with hot water.
4. Thoroughly dry lint screen with a clean towel. Replace
screen in dryer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleanin g the Dryer In terior
Removing Accum ulated Lint fr om Inside the
Dryer Cabin et
Lint should be removed every two years, or more often,
depending on dryer usage. Cleaning should be done by a
qualified person.
Ch an gin g the Dr u m Ligh t
The dryer light automatically turns on inside the dryer drum when
you open the door.
Explosion Hazard
To change the drum light
1. Unplug dryer or disconnect power.
Use nonflammable cleaner.
2. Open the dryer door. Locate the light bulb cover on the back
wall of the dryer. Remove the screw located in the lower right
corner of the cover. Remove the cover.
Failure to do so can result in death, explosion,
or fire.
To clean dryer drum
1. Make a paste with powdered laundry detergent and very
warm water.
2. Apply paste to a soft cloth.
OR
Apply a liquid, non-flammable household cleaner to the
stained area and rub with a soft cloth until all excess dye is
removed.
3. Turn bulb counterclockwise. Replace the bulb only with a 10-
watt appliance bulb. Replace the cover and secure with the
screw.
4. Plug in dryer or reconnect power.
3. Wipe drum thoroughly with a damp cloth.
4. Tumble a load of clean cloths or towels to dry drum.
NOTE: Garments which contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
dryer interior. These stains are not harmful to your dryer and will
not stain future loads of clothes. Dry unstable dye items inside
out to prevent dye transfer.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Unusual sounds
TROUBLESHOOTING
■
■
Has the dryer had a period of non-use?
If the dryer hasn’t been used for a while, there may be a
thumping sound during the first few minutes of operation.
First try the solutions suggested here and possibly avoid
the cost of a service call...
Is it a gas dryer?
The gas valve clicking is a normal operating sound.
Clothes are not drying satisfactorily
■
Check the following:
Is the lint screen clogged with lint?
Lint on load
■
■
Is the lint screen clogged?
Clean lint screen. Check for air movement.
Is the exhaust vent or outside exhaust hood clogged with lint,
restricting air movement? Run the dryer for 5-10 minutes.
Hold your hand under the outside exhaust hood to check air
movement. If you do not feel air movement, clean exhaust
system of lint or replace exhaust vent with heavy metal or
flexible metal vent. See “Installation Instructions.”
Is the load properly sorted?
Sort lint givers (towels, chenille) from lint takers (corduroy,
synthetics). Also sort by color.
■
■
Is the load too big or too heavy?
Dry smaller loads so lint can be carried to the lint screen.
Is the exhaust vent crushed or kinked? Replace with heavy
metal or flexible metal vent. See “Installation Instructions.”
Was the load overdried?
Has a fuse blown, or a circuit breaker tripped? Electric dryers
use 2 household fuses or breakers. The drum may be turning,
but you may not have heat.
Use correct dryer settings for load type. Overdrying can
cause lint-attracting static electricity. See “Drying, Cycle, and
Temperature Tips.”
Has an air dry cycle been selected? Select the right cycle for
the types of garments being dried. See “Drying, Cycle and
Temperature Tips.”
■
■
Was paper or tissue left in pockets?
Clean out pockets before drying.
Is pilling being mistaken for lint?
Pilling (surface fuzz) is caused by normal wear and
laundering.
For gas dryers, is the valve open on the supply line?
Are fabric softener sheets blocking the grille? Use only one
fabric softener sheet, and use it only once.
Stains on load or color change
■
Is the dryer located in a room with temperature below
45ºF (7ºC)?
■
Was dryer fabric softener properly used?
Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially-dried load can
stain your garments.
Proper operation of dryer cycles requires temperatures above
45ºF (7ºC).
■
■
Was a cold rinse water used? Was the load very wet?
Expect longer drying times with items rinsed in cold water
and with items that hold moisture (cottons).
■
■
Were items soiled when placed in the dryer?
Items should be clean before being dried.
Is the load too large and heavy to dry quickly?
Separate the load to tumble freely.
Were items properly sorted?
Sort light colors from dark colors. Sort colorfast items from
noncolorfast items.
Dryer will not run
Items shrinking
■
Check the following:
Is the power cord plugged in?
■
■
Was the dryer overloaded?
Dry smaller loads that will tumble freely.
Has a fuse blown, or has a circuit breaker tripped?
Was a regular fuse used? Use a time-delay fuse.
Is the dryer door firmly closed?
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Was the START button firmly pressed?
Is a cycle selected?
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Loads are wrinkled
■
■
Was the load removed from dryer at the end of the cycle?
Was the dryer overloaded?
Dry smaller loads that will tumble freely.
■
Did the load overdry?
Check the manufacturer’s care label. Match dryer setting to
load type. See “Drying, Cycle, and Temperature Tips.”
Odors
■
Have you recently been painting, staining or varnishing in
the area where your dryer is located?
If so, ventilate the area. When the odors or fumes are gone
from the area, re-wash and dry the clothing.
■
■
If the dryer is electric, is it being used for the first time?
The new electric heating element may have an odor. The odor
will be gone after the first cycle.
If the dryer is gas, there may be a gas leak.
Turn off the gas supply line, leave your house, and then call
your local gas company.
Garment damage
■
Check the following:
Were zippers, snaps, and hooks left open?
Were strings and sashes tied to prevent tangling?
Were care label instructions followed?
Were items damaged before drying?
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
If you need replacement parts
If you need to order replacement parts, we recommend that you
only use FSP® factory specified parts. These parts will fit right
and work right because they are made with the same precision
used to build every new WHIRLPOOL® appliance. To locate FSP
replacement parts in your area, call our Customer Interaction
Center at or your nearest designated service center.
For assistance and service
Call the Whirlpool Customer Interaction Center toll free:
1-800-253-1301.
Our consultants provide assistance with:
■
■
■
■
■
Features and specifications on our full line of appliances
Installation information
Use and maintenance procedures
Accessory and repair parts sales
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.)
■
Referrals to local dealers, repair parts distributors, and
service companies
Whirlpool designated service technicians are trained to fulfill the
product warranty and provide after-warranty service, anywhere in
the United States.
To locate the Whirlpool designated service company in your area,
you can also look in your telephone directory Yellow Pages.
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
Whirlpool Corporation
Customer Interaction Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
Accessories U.S.A
To order accessories, call the Whirlpool Customer Interaction
Center toll free at 1-800-442-9991 and follow the menu prompts.
Or visit our website at www.whirlpool.com and click on “Buy
Accessories Online.”
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
15
Download from Www.Somanuals.com. All Manuals Search And Download.
WHIRLP OOL® DRYER WARRANTY
ONE-YEAR FULL WARRANTY
For one year from the date of purchase, when this dryer is operated and maintained according to instructions attached to or furnished
with the product, Whirlpool Corporation will pay for FSP® replacement parts and repair labor to correct defects in materials or
workmanship. Service must be provided by a Whirlpool designated service company.
Whirlpool Corporation will not pay for:
1. Service calls to correct the installation of your dryer, including venting. Heavy 4 in metal exhaust vent must be used. Refer to the
venting section of this manual and your Installation Instructions.
2. Service calls to instruct you how to use your dryer, to replace house fuses or correct house wiring or reset circuit breakers, or to
replace owner accessible light bulbs.
3. Repairs when your dryer is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, floods, acts of God, improper installation (including, but not limited
to, venting with plastic or flexible foil), installation not in accordance with local electrical and plumbing codes, or use of products not
approved by Whirlpool Corporation.
5. Replacement parts or repair labor costs for units operated outside the United States.
6. Pickup and delivery. This product is designed to be repaired in the home.
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
WHIRLPOOL CORPORATION SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Outside the 50 United States, this warranty does not apply.
Contact your authorized Whirlpool dealer to determine if
another warranty applies.
Some states do not allow the exclusion or limitation of incidental
or consequential damages, so this exclusion or limitation may not
apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
If you need service, first see “Troubleshooting.” Additional help
can be found by checking “Assistance or Service,” or by calling
our Customer Interaction Center at 1-800-253-1301, from
anywhere in the U.S.A., or write: Whirlpool Corporation,
Customer Interaction Center, 553 Benson Road, Benton Harbor,
MI 49022-2692.
2/01
Dealer name____________________________________________________
Address ________________________________________________________
Phone number __________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or
installation date for in-warranty service.
Write down the following information about your dryer to better
help you obtain assistance or service if you ever need it. You will
need to know your complete model number and serial number.
You can find this information on the model and serial number
label/plate, located on your appliance as shown in “Parts and
Features.”
8528324
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
® DRYEL is a registered trademark of The Procter & Gamble Company.
3/01
© 2001 Whirlpool Corporation.
All rights reserved
Printed in the U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|