Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
ANTENNA OR COACIAL CABLE INPUT CONNECTION
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
DIGITAL TELEVISION TRANSITION NOTICE
DIGITAL TELEVISION TRANSITION NOTICE
This device contains a digital television tuner, so it should receive digital over the air
TV programming, with a suitable antenna, after the end of full-power analog TV
broadcasting in the United States on June 12, 2009. The nationwide switch to digital
television broadcasting will be complete on June 12, 2009, but your local television
stations may switch sooner. After the switch, analog-only television sets that receive
TV programming through an antenna will need a converter box to continue to receive
over-the-air TV. Watch your local stations to find out when they will turn off their
analog signal and switch to digital-only broadcasting.
For more information, call the FCC at 1-888-CALL-FCC (1-888-225-5322) or see
the NTIA at 1-888-DTV-2009.
ENERGY STAR DISCLAIMER
This Westinghouse product has earned the ENERGY STAR® for meeting U.S.
Federal energy efficiency guidelines as set by the Department of Energy and
Environmental Protection agency. The ENERGY STAR® program exists to provide
energy saving guidelines and help promote energy efficient products and practices.
Changes to certain features, settings and functions of this TV can change and/or
increase its power consumption. Depending on how settings are changed, power
consumption may exceed the limits required for ENERGY STAR® qualification. This
Westinghouse TV will operate at optimal energy efficiency in “Home” mode.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
IMPORTANT INFORMATION
Warnings
To reduce the risk of fire or electric shock:
•
•
Do not expose this product to rain or moisture.
Do not remove the rear cover. There are no user-serviceable parts inside.
Refer all servicing requirements to qualified service personnel.
•
The plug should be connected to a mains socket outlet with a protective
earthing connection.
The lightning flash with arrowhead inside an equilateral
triangle symbol is intended to alert the user to the presence
of uninsulated dangerous voltage within the product's
enclosure that may be of sufficient magnitude to constitute a
risk of electric shock.
The exclamation inside an equilateral triangle symbol is intended to
alert the user to related operating and maintenance instructions in
the user documentation accompanying the product.
WARNING!
This device must be operated with the original power supply.
WARNING!
To prevent injury, this apparatus must be securely attached to the floor/wall in
accordance with the installation instructions.
CAUTION:
The power supply outlet should be located near the LED TV and should be easily
accessible.
Always use the appropriate AC cord that is certified for your specific country.
Some examples are listed below:
•
•
•
USA – UL
Canada – CSA
Japan – Electric Appliance Control Act
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
NOTICES
Important Notices Concerning Power Cord Selection
The specific power cord for this LED TV is enclosed and has been selected
according to the country of destination. Use the enclosed power cord to prevent
electric shock. Observe the following guidelines if it is necessary to replace the
original cord set, or if there is no cord set enclosed. The female receptacle of the
cord set must meet IEC-60320 requirements and should look like Figure A1 below:
Figure A2
Figure A1
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL-
listed, and CSA-labeled. For LED TVs that are to be placed on a desk or table, type
SVT or SJT cord sets may be used. For LED TVs that are to be placed directly on
the floor, only SJT type cord sets may be used. The cord set must be selected
according to the current rating for the LED TV. Consult the table below for the
selection criteria of power cords used in the United States and Canada.
Cord Type Size of Conductor in Cord Maximum Unit Current Rating
18 AWG
16 AWG
14 AWG
18 AWG
17 AWG
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
SJT
SVT
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
FCC COMPLIANCE STATEMENT
This equipment has been tested and complies with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy, and may cause
harmful interference to radio communications if not installed and used in accordance
with the instructions. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the LED TV and the receiver.
Connect the LED TV to an outlet on a circuit separate from to which the
receiver is connected.
•
If the interference persists even after performing the above measures,
consult the Westinghouse Service Center or an experienced radio/TV
technician for assistance.
FCC Warning
To assure continued FCC compliance, use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. If a BNC cable is
used, use only a shielded BNC (5) cable. Also, any unauthorized changes or
modifications not expressly approved by the manufacturer will void the user's
authority to operate this device.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
Make sure to note and follow all warnings and instructions marked on the LED TV.
Observe the following safety instructions.
•
•
•
•
•
•
•
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
•
•
Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
•
Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
•
•
Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
•
•
Unplug this apparatus during lightning storms or when unused for long
periods of time.
Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
Circuit Overload
Do not overload wall outlets, extension cords, or power strips. This can result in a fire
or electronic shock.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or
pinched by items placed upon or against them. Periodically inspect the cords for
damage. Install the LED TV near a wall socket outlet where the power cord can be
readily accessed.
Ventilation
The slots and openings on the cabinet are provided for necessary ventilation. To
ensure reliable operation of the LED TV and to protect it from overheating, these
slots and openings must never be blocked or covered.
Never cover the slots and openings with a cloth or other materials.
Do not block the openings by placing the LED TV on a bed, sofa,
rug or other similar surface.
Do not place the LED TV in a built-in installation such as a
bookcase or a rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
WARNINGS AND PRECAUTIONS
•
•
Do not orient the LED TV towards direct sunlight to reduce glare.
If the LED TV will not be used for a long period of time, unplug the unit and
remove the batteries from the remote control.
•
•
Avoid touching the display screen by hand or any object.
Never remove the rear cover. The LED TV interior contains high-voltage
parts. You may be seriously injured if you touch them.
•
•
Always handle the LED TV with caution when moving it.
Do not install the LED TV in airtight compartments, or in areas where it can
be exposed to water or high temperature.
•
•
•
Ensure that the area around the LED TV is clean and free of moisture.
Do not place anything on the LED TV that can hinder heat dissipation.
Do not place naked flame sources, such as lighted candles, on or near the
LED TV.
•
•
•
Do not place anything on the LED TV that can cause liquid to splash on it
(e.g. flower vase).
Do not place heavy objects on the LED TV, audio/video cables, or power
cord.
If the LED TV emits smoke, abnormal noise, or a strange odor, immediately
turn it off and contact the Westinghouse Service Center by:
–
–
–
Contacting the Westinghouse Customer Service at (800) 701-0680.
E-mailing us at [email protected].
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
ANTENNA INSTALLATION SAFETY
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the LED TV, be sure the
antenna or cable system is grounded to prevent voltage surges and built-up static
charges. Article 810 of the National Electrical Code, ANS/NFPA 70, provides
information on proper grounding of the mast and supporting structure, grounding of
the lead-in wire to an antenna discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode.
Antenna Grounding According to the National
Electrical Code, ANSI/NFPA 70
Antenna lead in wire
Antenna discharge unit
(NEC Section 810-20)
Grounding clamps
Grounding Conductors
(NEC Section 810-21)
Electric service
equipment
Grounding clamps
Power service grounding
electrode system (NEC Art
250 part H)
NEC: National Electrical Code
Lightning
For added protection for the LED TV during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. DO NOT disconnect the antenna or the power cord during
a heavy storm—lightning may strike while you are holding the
cable cord, causing serious injury. Turn off the LED TV and wait for
the weather to improve.
Power lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT INFORMATION
CLEANING THE LED TV
•
Make sure the LED TV is turned off and the power cord is
disconnected from the power outlet.
•
Never spray or pour any liquid directly onto the screen or the
case.
To clean the screen:
1
Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other
particles.
2
If it is still not clean, apply a small amount of non-ammonia, non-alcohol
based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1
2
Wipe the case with a soft, dry cloth.
If it is still not clean, apply a small amount of non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then
wipe the surface.
Dolby-Digital Notice
Manufactured under license from Dolby Laboratories. Dolby and the double-D
symbol are registered trademarks of Dolby Laboratories.
Licensing and Patent Information
This WESTINGHOUSE product may be covered by one or more U.S. and foreign
details.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROL PANEL
CONTROL PANEL
1
2
3
4
5
D
C
I
N
TUNER
VGA
A
U
D
I
O
I
N
V
I
D
E
O
R
IN
L
R
OUT
L
Item
Description
Displays the LED TV setup screen.
1. MENU
2. Volume +/-
•
•
•
•
•
•
Adjusts the volume during playback.
Selects an item on a menu screen.
Switches the channel during TV viewing.
Selects an item on a menu screen.
Selects the video input source.
3. Channel +/-
4. INPUT
Executes a command on a menu screen.
5. Power
Toggles the power on and off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMINALS
TERMINALS
D
C
I
N
TUNER
VGA
A
U
D
I
O
I
N
V
I
D
E
O
L
IN
R
L
OUT
R
DC IN
TUNER
VGA
AUDIO IN
VIDEO
R
IN
L
R
OUT
L
Item
Function
1. DC in
Connects the AC to DC adapter from this outlet to a
power source.
2. Audio in
3. VGA
Connects to the audio out port of a computer.
Connects to a computer or other device with a VGA
output using a 15-pin VGA cable.
4. Composite AV input
Connect to an external AV device such as a VCR, DVD
player, set-top box, or game system.
5. TV tuner
6. Audio out
7. HDMI 1/2
Connects the LED TV to an antenna or cable service.
Connect to an analog audio output device.
Connects to an external AV device such as a VCR,
DVD player, set-top box, or game system.
8. USB Service port
9. SPDIF audio out
For service only.
Connects to an external digital audio receiver.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL
REMOTE CONTROL
Item
Description
Mutes the sound. Press again to toggle the
sound back on.
1. Mute
Toggles the TV power on or off.
2. Power
3. Channel keys
Use to key in the channel number.
Executes a channel entry.
4. Enter ENT
Sets the sleep timer for the LED TV to turn off
automatically.
5. Sleep
1
3
2
6. VGA
Switches to the VGA input source.
Selects a preset viewing options.
Switches to the TV input source.
Selects the video display format.
Ajusts the system volume.
7. Picture Mode
8. TV turner
9. Aspect ratio
10. Vol +/-
4
6
5
7
8
9
Switches to other TV channels.
Selects the video input source.
11. Ch
/
12. Input
10
11
Displays the Electronic Program Guide (EPG). It
contains the program information for the channel
you’re watching.
12
13
14
13. EPG
15
16
14. CC
15. Info
Toggles the closed caption display on or off.
17
19
Displays the input source or channel information
as well as the system time.
18
20
Toggles the Multichannel Television Sound
options.
16. MTS
21
22
24
23
25
17. Arrow keys
18. Select
Navigate through the on-screen menus.
Confirms the selection.
Accesses the LED TV setup menus.
Switches to the last selected channel.
19. Menu
20. Return
Switches to the favorite channels (for details on
how to save a new favorite channel, see
page 28).
21. Favorite
22. HDMI1
23. HDMI2
24. YPbPr1
Selects HDMI1 as the input source.
Selects HDMI2 as the input source
Selects VGA-Component as the input source.
Selects the Composite AV device as the input
source.
25. Video1
13
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL OPERATION
REMOTE CONTROL OPERATION
INSTALLING THE REMOTE CONTROL BATTERIES
CAUTIONS:
•
Only use AAA batteries.
•
Do not mix new and old batteries. This may result in cracking or leakage, which
may pose a fire risk or lead to personal injury.
•
Insert batteries according to the (+) and (-) markings. Inserting the batteries
incorrectly may result in cracking or leakage, which may pose a risk of fire or
lead to physical injury.
•
•
•
Dispose of used batteries in accordance with local laws and regulations.
Keep batteries away from children and pets.
When the remote control will not to be used for an extended period, remove the
batteries.
1
Remove the battery cover.
2
Insert the batteries. Make sure the (+) and (–) marks on the
batteries match those inside the compartment.
Re-attach the battery cover.
3
REMOTE CONTROL TRANSMISSION RANGE
Transmission range depends upon the reception angle.
The range of coverage is 20° horizontal/vertical at a
distance of 10 feet from the LED TV.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
LED TV BASE
LED TV BASE
CAUTION:
The LED TV unit may be too heavy for one person to lift. If this is the case,
make sure to ask for assistance in handling the LED TV to prevent
physical injury and/or damage to the unit.
INSTALLING THE LED TV BASE
1
2
3
4
5
6
7
8
9
Open the LED TV carton box.
Remove the LED TV base.
Remove the plastic bag.
Remove the two top carton stabilizers from the LED TV.
Remove the protective plastic covering the LED TV.
Grasp the two sides of the LED TV and then pull it out of the carton box.
Remove the two bottom carton stabilizers from the LED TV.
Lay the LED TV on a clear, flat, and stable surface.
Align the base to the bottom side of the LED TV and use four M4 x 18 screws
to secure it.
10 Carefully orient the LED TV in an upright position.
11 Use one M5 x 16 screw to fix the stand base and LED TV on the desk.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVING THE LED TV BASE
REMOVING THE LED TV BASE
If you intend to repack the LED TV unit (for shipping or storage) or you want to
change the installation to a wall mount option, you must first remove the LED TV
base.
1
2
3
4
5
Turn off the LED TV and all connected devices.
Disconnect the power cord from the LED TV.
Disconnect all signal cables from the I/O port terminals.
Remove the M5 x 16 screw securing the base to the desk.
Lay the LED TV on a clear, flat, and stable surface.
6
7
Remove the screws securing the base to the LED TV.
Detach the base from LED TV.
8
Pack the screws you removed in step 5 together with the LED TV base for
future reassembly.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
ANTENNA CONNECTION
ANTENNA CONNECTION
OUTDOOR ANTENNA CONNECTION
Cable TV lead in
VHF, UHF or VHF/UHF
combination antenna
75 ohm coaxial cable (round)
300-75 ohm ADAPTER
RF IN
300 ohm twin-lead (flat)
(Not supplied)
Separate VHF/UHF Antenna
VHF Antenna UHF Antenna
Home Antenna
terminal (75 ohm)
300 ohm twin-lead
COMBINER
(Not supplied)
300 ohm twin-lead
IN OUT
75 ohm coaxial cable
NOTE:
The F-type connector should be finger-tightened only.
When connecting the RF cable to the LED TV, do not
tighten F-type connector with any tool. If tools are
used, it may cause damage to the LED TV (e.g.
breaking of internal circuit).
CABLE TV (CTV/DTV) CONNECTION
The unit has a TV tuner (75 ohm coaxial cable connector) located on the rear I/O
panel for easy cable hookup. When connecting the 75 ohm coaxial cable to the unit,
screw the 75 ohm cable to the TV tuner. Some cable TV companies offer premium
pay channels. Since the signals of these channels are scrambled, a cable TV
converter/descrambler is usually provided to the subscriber by the cable TV
company. This converter/descrambler is necessary for normal viewing of the
scrambled channels. (Set your TV to channel 3 or 4. Typically one of these channels
is used. If a channel is unknown, consult your cable TV company.) For more specific
instructions on installing cable TV, consult your cable TV company. One possible
method of utilizing the converter/descrambler provided by your cable TV company is
explained below.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL DEVICE CONNECTIONS
•
•
A position on the RF switch (not supplied) – You can view all unscrambled
channels by using the TV's channel keys.
B position on the RF switch (not supplied) – You can view the scrambled
channels via the converter/descrambler by using the converter's channel
keys.
RF switch (not supplied)
Two-set
A
signal
OUT
IN
B
Cable TV line
splitter
(Not
supplied)
Cable TV
converter/descrambler
(Not supplied)
EXTERNAL DEVICE CONNECTIONS
IMPORTANT:
•
•
•
Turn off the LED TV first before connecting an external device to prevent
any possible damage or physical injury.
For more information about external device connections, see the operation
manual of the external device you wish to connect to the LED TV.
Make sure that the correct cables are connected to each terminal.
Improper cable connections may cause damage to the LED TV.
You can enjoy picture and sound by connecting various audio-video devices to the
terminals located on the rear and side I/O panels of the LED TV.
•
•
TV cable input – You can use a commercially available audio/video cable.
Component (YPbPr) input – Picture can be displayed only when a 480i,
480P, 720P, 1080i, or 1080P signal is received.
•
HDMI input – Picture can be displayed only when a 480i, 480P, 720P, 1080i,
or 1080P signal is received. When you connect to the HDMI terminal with a
DVI-HDMI conversion cable, there is a possibility that the picture may not
display correctly.
•
Audio output – You can output audio signals from the LED TV set through
the analog audio out and SPDIF terminals.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTERNAL DEVICE CONNECTIONS
The following diagram shows the external device connections.
Audio amplifier
VGA
AUDIO OUT
3.5 mm stereo
mini jack cable
Audio cable
RGB cable
SPDIF cable
DC IN
TUNER
VGA
AUDIO IN
VIDEO
R
IN
L
R
OUT
L
Antenna cable /
Cable TV line
AC to DC
adapter
Composite AV
cable
HDMI-HDMI
cable
DVI-HDMI
cable
Home video
game system
VCR
DVD player
with a DVI
terminal
DVD player
Camcorder
Power outlet
with an
HDMI
Antenna cable /
Cable TV line
terminal
DVD player
Digital TV tuner
19
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
POWER CONNECTION
CONNECTING AC POWER
IMPORTANT:
The LED TV is designed to be powered via an AC adapter. Use ONLY the
AC adapter included in the package. Turn off all connected devices before
plugging the AC adapter into the power outlet.
Connect the power cord of the AC adapter to the LED TV then to a proper AC outlet.
D
C
I
N
TUNER
VGA
A
U
D
I
O
I
N
VIDEO
R
IN
L
R
OUT
L
INITIAL SETUP
Press on the control panel or on the remote control to turn on the LED TV. Select
the desired language and select Yes to use the SetupWizard. The SetupWizard will
guide you on how to set up the LED TV’s operational settings.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
CABLE OR SATELLITE BOX CONNECTION SETUP
Select Language
Use the up and down arrows on your HDTV
control panel or remote control to select the
language to be used for menus and
messages. Press SELECT to continue.
Time Zone
Use the up and down arrows on your HDTV
control panel or remote control to select your
local time zone. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Power On Mode
Use the up and down arrows on your HDTV
control panel or remote control to select the
power on mode. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Channel Scan - Cable/Satellite Box
Select “Click here to connect a Cable Box or
Satellite Box.” and press SELECT on your
remote control to start scanning channels.
Press SELECT to continue. Press Go Back
to return to the previous screen.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
Cable/Satellite Box Input
Use the up and down arrows on your HDTV
control panel or remote control to select the
input connected to the set top box. Press
SELECT to continue. Press Go Back to
return to the previous screen.
RF Warning
Use the up and down arrows on your HDTV
control panel or remote control to select.
Select “Proceed” and then press SELECT to
search the program. Press Go Back to return
to the previous screen.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
OTHER INPUT SOURCE CONNECTION SETUP
Select Language
Use the up and down arrows on your HDTV
control panel or remote control to select the
language to be used for menus and
messages. Press SELECT to continue.
Time Zone
Use the up and down arrows on your HDTV
control panel or remote control to select your
local time zone. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Power On Mode
Use the up and down arrows on your HDTV
control panel or remote control to select the
power on mode. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Let's Get Connected
Select “Click here to connect a Game,
Blu-Ray, DVD, or other player.” and press
SELECT on your remote control. Press
SELECT to continue. Press Go Back to return
to the previous screen.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
Select Input Source
Use the up and down arrows on your HDTV
control panel or remote control to select the
input source. Press SELECT to continue.
Press Go Back to return to the previous
screen.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
ANTENNA OR COACIAL CABLE INPUT CONNECTION SETUP
SETUP
Select Language
Use the up and down arrows on your HDTV
control panel or remote control to select the
language to be used for menus and messages.
Press SELECT to continue.
Time Zone
Use the up and down arrows on your HDTV
control panel or remote control to select your
local time zone. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Power On Mode
Use the up and down arrows on your HDTV
control panel or remote control to select the
power on mode. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Let’s Get Connected
Select “Click here to scan channels from the
Antenna or coaxial cable input.” and press
SELECT on your remote control to start
scanning channels. Press SELECT to
continue. Press Go Back to return to the
previous screen.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTION
Select Channel Scan Type
Use the up and down arrows on your HDTV
control panel or remote control to select the
channel scan type. Press SELECT to continue.
Press Go Back to return to the previous
screen.
Channel Scan in progress
The channel scan may take a while to
complete. When the scan is complete, you will
be able to watch your local TV programming.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
BASIC OPERATIONS
TURNING THE POWER ON AND OFF
Turning on the power
Press
on the control panel or on the remote control to turn on the LED TV.
Turning off the power
Press
on the control panel or on the remote control to turn off the LED TV. The
LED behavior will depend on the enabled Power settings.
LED indicator
Operation
Turns from none to red. Turn the power on.
Turns from red to none. Turn the power off.
NOTES:
•
If you are not going to use the TV for a long time, be sure to disconnect the
power cord from the wall outlet and remove the batteries from the remote
control.
•
In standby mode, a small amount of electricity is still consumed even when the
power is turned off.
ADJUSTING THE VOLUME
Volume
Press Vol+ to increase the volume; press Vol- to
Mute
decrease the volume.
Mute
Press
to turn off the sound. The mute icon appears
Volume
on the screen. Press again to turn on the sound.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
CHANGING CHANNELS
Follow the instructions below to change channels.
Using the Ch
/
Buttons
Browse channels
To browse through the available channels, press Ch
/
on
the remote control or on the control panel.
Using the Channel Keys
Selecting channel
To change to a certain channel, key in the channel number using
the channel keys and press ENT.
Selecting digital channel
To select a digital channel, key in the digital channel number using
the channel keys and the • key, then press ENT.
Using the Favorite Keys
Selecting favorite channels
To select a favorite channel, press the Favorite button (A, B, C, or
D) corresponding to the preferred channel.
Saving a channel as a favorite
1
Switch to the channel you want to add as a favorite.
2 Press and hold the Favorite button which you want to add
the current channel to for 3 seconds.
3 The Channel Saved message appears to confirm the new
favorite channel item.
SELECTING THE INPUT SOURCE
There are two ways to select the video input source.
Using the Individual Input Keys
TV, VGA, Video, YPbPr, HDMI Keys
Press any of the following remote control keys to change the input
source: TV, VGA, Video1, YPbPr1, HDMI1, or HDMI2.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
BASIC OPERATIONS
Using the Input Key
Select source using Input Key
Press Input
2 A list of supported video sources is displayed.
1
.
3 Press
4 Press
/
to select the preferred source.
to switch to the selected input source.
ADJUSTING THE DISPLAY FORMAT
The input source can sometimes affect the way images are displayed on-screen.
You can adjust the display format to view the image properly.
Format Options
Press
repeatedly to toggle the display format. As you toggle
each option on, the actual display will change accordingly. The
available options are:
•
•
•
Standard: Picture is displayed in its original size.
Fill: Picture is displayed to cover the entire screen.
Overscan: Picture is scaled up to fit the display area.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
SETUP MENUS
SETUP MENU OPERATION
Use the setup menus to configure the various operational settings of the LED TV.
Displaying the setup menu screen
Press on the remote control or MENU on the control panel to display the setup
menu screen.
Navigating the setup menu screen
Use the buttons on the remote control or on the control panel to navigate through
the menu screens.
D
C
I
N
TUNER
VGA
A
U
D
I
O
I
N
VIDEO
R
IN
L
R
OUT
L
Action
Remote Control
Control Panel
Displays or closes the menu bar.
MENU
•
•
•
•
Select and display a primary menu.
Adjust sub-menu options.
Select and display a sub-menu.
Select a sub-menu or a sub-menu
option.
Volume +/- then
INPUT
/
/
then INPUT
Channel +/- then
INPUT
then INPUT
•
•
Returns to the primary menu tab
from a sub-menu screen.
Returns to the previous screen.
MENU
INPUT
Applies the selected menu setting.
INPUT
30
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
PICTURE
Use the Picture sub-menus to configure the display quality.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select Picture to display the Picture sub-menu. The following
options are available: Picture Settings, Screen Size, VGA Settings, Color
temperature, Advanced Picture Settings.
Picture Settings
Adjust the picture quality including brightness, contrast, color, tint, sharpness.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Picture mode
Use this sub-menu to select one of four preset view options optimized for different
viewing conditions.
The following options are available:
•
•
•
•
Standard: Select for standard picture.
Movie: Select for a finely detailed picture.
User: Select for standard picture.
Dynamic: Select for enhanced picture contrast and sharpness.
Brightness
Use Brightness to adjust the luminance level.
Adjusting Brightness
1
Use the
/
keys to select Brightness and press
keys on the remote control to adjust the brightness level.
to save and exit the screen.
.
2 Press the
3 Press
/
Contrast
Use Contrast to adjust the brightness to darkness ratio.
Adjusting Contrast
1
Use the
/
keys to select Contrast and press
keys on the remote control to adjust the contrast level.
to save and exit the screen.
.
2 Press the
3 Press
/
32
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Color
Use Color to adjust the color intensity.
Adjusting Color
1
Use the
/
keys to select Color and press
keys on the remote control to adjust the Color level.
to save and exit the screen.
.
2 Press the
3 Press
/
Tint
Use Hue to adjust the balance of the red, green, and blue colors in the display.
Adjusting Tint
The following options are available:
1
Use the
/
keys to select Tint and press
keys on the remote control to adjust the Tint level.
to save and exit the screen.
.
2 Press the
3 Press
/
Sharpness
Use Sharpness to adjust the sharpness or softness of the display.
Adjusting Sharpness
1
Use the
/
keys to select Sharpness and press
.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
2 Press the
/
keys on the remote control to adjust the sharpness level.
3 Press
to save and exit the screen.
Screen Size
Press
/
to selet the display aspect ratio till the picture is fit onto the screen.
The options are different according to different input source.
VGA source
Two settings are available:
•
•
Wide: Use to watch wide size content.
Dot by Dot: means NOT any scaling to original input pixels size.
AV/YPbPr/HDMI/TV
Four settings are available:
•
•
•
•
Normal: suitable to watch common TV program.
Wide: do horizontal scaling on the wide panel.
Cinema: for the 2.39:1 (perhaps marked as 2.40:1 on the disc) film.
Zoom: suitable to view the analog TV which has wide(16:9) content on the
16:9 panel.
Adjusting Screen Size
1
Use the
/
keys to select Screen Size and press
keys on the remote control to select the desired option.
to save and exit the screen.
.
2 Press the
3 Press
/
VGA Settings
VGA Settings Menu is available only in VGA DB15 or DVI mode. When DVI signal
input, only Horizontal Position and Vertical Position can be adjusted.
Press
it.
/
to highlight one of the following options, then press SELECT to select
34
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Auto Adjust
Automatically adjust Clock, Phase, H-Position and V-Position settings.
In order to get a good result, you should open a "filling the screen" picture before
executing Auto Adjust.
H.Position
Shift the screen slightly to left or right.
V.Position
Shift the screen slightly up or down.
Clock
Adjust the DB15 picture signal sampling clock rate.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Phase
Adjust the DB15 picture signal sampling phase. It maybe affect the definition. Wrong
value maybe result the interference.
Reset
Reset the parameters of current menu to default value.
Adjusting VGA Settings
1
Use the
/
keys to select VGA Settings and press
keys on the remote control to select the desired option.
to save and exit the screen.
.
2 Press the
3 Press
/
Color Temperature
Use Color temperature to adjust the level of white balance in the display.
Three settings are available:
•
•
•
Warm: Pictures appear more reddish.
Normal: Pictures appear more white.
Cool: Pictures appear with a bluish tint.
Adjusting Color Temperature
1
Use the
/
keys to select Color temperature and press
.
2 Press the
3 Press
/
keys on the remote control to select the desired option.
to save and exit the screen.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Advanced Picture Settings
•
Dynamic Contrast (Off/On)
The system will adjust the luminance curve by analyzing the picture content
dynamically.
•
Film Mode (Off/On)
For the 2:2 or 3:2 format signal of cinema, enable special pixel process to reduce the
flick of moving area.
•
Noise Reduction (Off/On)
You can clear up analog TV signal by reducing the dot noise. This feature is not
available at VGA or Media source.
•
MPEG Noise Reduction (Off/On)
Similar with the Noise Reduction, you can set to reduce the block noise.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
SOUND
Use the Sound sub-menus to configure the sound quality.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select Sound to display the Sound sub-menu. The following
options are available: Sound Settings, Analog Sound, Digital Sound, Digital Audio
Output, Equalizer Settings, and SRS TruSurround Settings.
Sound Settings
Adjust the picture quality including sound mode, bass, treble, balance.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Sound mode
Use this sub-menu to select one of four preset view options optimized for different
listening conditions.
The following options are available:
•
•
•
•
Standard: Select for standard picture.
Soft: Select for a finely detailed picture.
User: Select for standard picture.
Dynamic: Select for enhanced picture contrast and sharpness.
Bass
Use Bass to calibrate low-pitched sounds.
Adjusting Bass
1
Use the
/
keys to select Bass and press
keys on the remote control to adjust the Bass level.
to save and exit the screen.
.
2 Press the
3 Press
/
Treble
Use Treble to calibrate high-pitched sounds.
Adjusting Treble
1
Use the
/
keys to select Treble and press
keys on the remote control to adjust the Treble level.
to save and exit the screen.
.
2 Press the
3 Press
/
39
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Balance
Use Balance to adjust the sound balance between the L/R speakers.
Adjusting Balance
1
Use the
/
keys to select Balance and press
keys on the remote control to adjust the Balance level.
to save and exit the screen.
.
2 Press the
3 Press
/
Analog Sound (SAP/Stereo/Mono)
Available at analog TV channels.
Set the preferred sound track of analog channels. Stereo and SAP exist on some
channels. Generally SAP is a second language sound or help the people with
hearing impair.
Digital Sound (English/French/Spanish)
Available at digital TV channels.
Set the preferred sound track of digital channels. French and Spanish exist on some
channels.
Digital Audio Output (PCM/Raw/Off)
Set the audio output type of coax or optical terminal. Raw means output the original
format of audio stream. PCM can be matched with most AV amplifiers.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Equalizer Settings
Use this sub-menu to select one of four preset audio options optimized for different
sounding conditions.
The following options are available:
•
•
•
•
Rock: Sets the equalizer to the Rock mode.
Pop: Sets the equalizer to the Pop mode.
Jazz: Sets the equalizer to the Jazz mode.
User: Uses the customized settings.
SRS Trusurround Settings
Use this sub-menu to set the sound effects.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
CHANNEL
Use the Channel sub-menus to configure the channel.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select Channel to display the Channel sub-menu. The following
options are available: Channel List, Favorite List, Channel Settings, Signal Type,
Auto Channel Search.
NOTE: The menu is available only at TV source.
Channel List
You can view all the channels and choose one quickly.
"ABC": Label of the Channel
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Favorite List
All of you favorite channels are listed in this menu, and you can choose them quickly.
Channel Setting
Set the favorite channels, skipped channels, label of channels.
•
•
•
Skip: Set the channel to be skipped when using CH+/CH- to view channels.
Favorite: Set the channel to your favorite list.
Label: Rename label of the channel.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Change the settings
•
Skip & Favorite
Press
Press
/
to select the channel you want to set.
/
to highlight corresponding item, and press SELECT to set or cancel.
•
Label
Press
/
/
to select the channel and SELECT to enter the edit state.
Press
to select the character, press
/
to move the cursor. Total seven
letters.
Signal Type
Set to Air or Cable according to your antenna source. When set to Air, TV can catch
8VSB broadcasting signal. When set to Cable, TV can catch analog and clear
64QAM/256QAM broadcasting signal.
Auto Channel Search
Select Auto Channel Search and press ENT. Two options are available:
•
Cable: Choose this setting if you are receiving TV channels with a CATV
(cable TV).
•
AIR: Choose this setting if you are receiving TV channels with an antenna
(over the air).
Auto Search automatically creates a list of receivable channels for the selected
source.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
PARENTAL CONTROL
Use the Channel sub-menus to configure the parental control.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select Parental Control to display the Parental Control sub-
menu. The following options are available: Lock Parental Control, V-CHIP, Change
Password, Keypad Lock, Source Lock.
Lock Parental Control
The following items are only available if the password input is correct.
V-CHIP
•
US V-Chip
Rating system used at USA.
TV Rating: Use this sub-menu to customize US TV Rating programs.
–
45
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Rating
TV-Y
TV-Y7
TV-G
Description
Suitable for young children.
May not be suitable for children under 7.
Suitable for all audiences.
TV-PG
TV-14
Parental guidance suggested.
Parental guidance suggested for children under 14.
Suitable for mature audiences only; may be unsuitable for children
under 17.
TV-MA
FV
D
L
Fantasy violence, combative situations.
Suggestive dialogue.
L Coarse language.
S
Sexual situations.
V
Violence.
–
Movie Rating: Use this sub-menu to select the ratings of allowable movies.
Rating
Description
Contains nothing most parents will consider
offensive for even their youngest children to see
or hear; suitable for young children.
G
May contain some material parents might not like
to expose to their young children-material that will
clearly need to be examined or inquired about
before children are allowed to view the film.
May contain some scenes of drug use; use of one
of the harsher sexually-derived words may be
heard. May be inappropriate for preteens.
PG
PG-13
46
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Rating
Description
May contain some adult material. Parents are
urged to learn more about the film before letting
their children view it.
R
May contain explicit sex scenes, an accumulation
of sexually-oriented language, and/or scenes of
excessive violence. Suitable for adult audiences
only. Rating does not signify that the film is
obscene or pornographic.
NC-17
Contains extreme violence or explicit sex; suitable
for adult audiences only.
X
•
Canada V-Chip
Rating system used at Canada.
–
Canada English: Use this sub-menu to select the classification categories
(based on Canadian ratings) of allowable TV programs and movies.
Rating
E
Description
Exempt shows
C
C8+
G
PG
14+
18+
Suitable for viewing by children of all ages.
Not suitable for children under 8 years of age.
Suitable for general audiences.
Parental guidance advised.
Suitable for people 14 years of age or older.
Suitable for people 18 years of age or older.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
–
Canada French: Use this sub-menu to select the ratings of allowable TV
programs and movies. These ratings are based on the classification
categories determined by La Régie du cinéma du Québec.
Rating
E
Description
Exempt shows
G
For general audiences.
8 ans +
13 ans+
16 ans+
18 ans+
Not suitable for children under 8 years of age.
Not suitable for persons under 13 years of age.
Not suitable for persons under 16 years of age.
Not suitable for persons under 18 years of age.
•
Block UnRated Show
Control whether lock the program that have not any valid rating flag.
Downloadable Rating
Control the RRT5 setting which are valid only at some digital cable channels.
Clear Downloadable Data
•
•
Select to clear the previous downloadable rating data.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Change Password
Change Password allows you to change your current password.
Changing Password
1
Use the
/
keys to select Change Password and press
.
2 Use the Channel keys to enter the current password and press
3 Use the Channel keys to enter the new password and press
.
.
4 Use the Channel keys to enter the new password again for confirmation
and press
.
5 Press
to save and exit the screen.
Source Lock
Press
/
to select the source you want to lock, then press SELECT to set it to
lock. If anyone want to use this source, the password is needed.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
SETUP
Use the Settings sub-menus to configure the LED TV operational setup and view the
current firmware version.
Press
on the remote control or MENU on the control panel to display the setup
menu screen then select Setup to display the Settings sub-menu. The following
options are available: Closed Captions, Menu Language, Clock, OSD Timer, Power
Light.
Closed Captions
Use Closed Captions to configure the settings for closed captioning in TV programs.
•
Caption Display
Display or hide the CC.
Analog Caption Type
•
Select from below closed-caption modes for analog programs.
CC1,2,3,4: Displays corresponding caption channel of a analog program. (Usually
be set to CC1 for most programs).
Text1,2,3,4: Displays corresponding text service channel of a analog program.
•
Digital Caption Type
Applies only to digital channels with closed caption.
Service1,2,3,4,5,6: These are different service data channels.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
•
Digital CC Preset (Default/Custom)
If set to Custom, Digital CC Style is available.
The following options are available:
–
–
–
–
–
Closed Captions: Can be set to ON or OFF.
Analog Type: Can be set to CC1,CC2, CC3, CC4, T1, T2, T3, or T4.
Digital Type: Can be set to CS1, CS2, CS3, CS4, CS5, or CS6.
CC Size: Can be set to As Broadcaster, Small, Medium, or Large.
CC Font: Can be set to As Broadcaster, Style 1, Style 2, Style 3, Style 4,
Style 5, Style 6, or Style 7.
–
–
–
–
CC Opacity: Can be set to As Broadcaster, Solid, Translucent,
Transparent, or Flashing.
Text Color: Can be set to As Broadcaster, Black, White, Green, Blue,
Red, Cyan, Yellow, or Magenta.
CC Background Opacity: Can be set to As Broadcaster, Solid,
Translucent, Transparent, or Flashing.
CC Background Color: Can be set to As Broadcaster, Black, White,
Green, Blue, Red, Cyan, Yellow, or Magenta.
Adjusting Closed Captions Settings
1
Use the
/
keys to select Closed Captions and press
.
2 Use the
3 Use the
4 Press
/
keys to select the desired Closed Captions option.
keys to adjust the value.
/
to save and exit the screen.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
Menu Language
Use Menu Language to select the language to display on the screen: English,
French, or Spanish.
Adjusting Menu Language
1
Use the
/
keys to select Menu Language and press
.
2 Press the
Spanish.
/
keys on the remote control to select English, French or
3 Press
to save and exit the screen.
Clock
Set the Time Zone, Auto Clock, Setup Time, Day of Week or Daylight Saving Time.
•
Time Zone
Hawaii/Alaska/Pacific/Central/Mountain/Eastern/Samoa/Newfounland/Altantic
Auto Clock
•
If set it to ON , the TV will sync the local clock according to the DTV broadcasting
time automatically. Otherwise you can set the time manually.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
•
Setup Time
Set Auto Clock to Off, then you can set the time manually .
NOTE: In the case of loss of power, the clock setting will be lost.
Day of Week
The TV will calculate current day of week according to the time.
Daylight Saving Time
•
•
When Auto Clock set to ON, this item is available to enable daylight saving option or
not.
OSD Timer
Use OSD Timeout to adjust the OSD duration on the screen: 10 sec, 20 sec, or 30
sec.
Adjusting OSD Timer
1
Use the
/
keys to select OSD Timer and press
.
2 Press the
30 sec.
/
keys on the remote control to select 10 sec, 20 sec, or
3 Press
to save and exit the screen.
Power Light
Set to select power light.
Adjusting Power Light
1
Use the
/
keys to select Power Light and press
keys on the remote control to select ON or OFF.
to save and exit the screen.
.
2 Press the
3 Press
/
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SETUP MENUS
OTHERS
Blue Back
Set the screen background color blue or not when no valid signal input. When analog
TV input and has no signal, snow noise will display if this option is cleared.
No Signal Power Off
If it is set, TV will automatically enter standby after 10 minutes without signal input.
No Operation Power Off
If it is set, TV will automatically enter standby after 3 hours without any operation.
All Reset
When you highlight the item, the system will note you that “Attention! If [All Reset]
was executed, TV system is reset” A and if you are sure to reset, press SELECT to
reset.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL MOUNT OPTION
WALL MOUNT OPTION
The LED TV has been fitted with VESA FPMPMI compliant mounting holes. These
200 x 100 mm mounting holes allow the unit to be mounted on a wall. Use the four
M4 x L10 mm screws to wall mount the LED TV.
DC IN
TUNER
VGA
AUDIO IN
VIDEO
R
IN
L
R
OUT
L
WALL MOUNT INSTALLATION REMINDERS
•
Remove the LED TV base first before mounting the unit on a wall.
•
It is the user's responsibility to use a UL listed wall mount unit rated to
support the weight of this LED TV.
•
Please consult qualified contractors for wall mount installation.
CAUTION:
The incomplete or improper mounting of this unit to a wall may cause it to fall down
resulting to property damage and/or potentially serious injury.
55
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
TROUBLESHOOTING
Problem
Corrective Action
•
Make sure the power indicator is illuminated
blue.
•
Make sure the power cord is securely
connected to the AC-in jack and is plugged
into a functional AC outlet. You may want to
plug in another electrical device to the power
outlet to verify that it is supplying the proper
voltage.
No power
Power is suddenly
turned off.
Make sure the sleep timer is turned off.
•
•
•
Press only one button at a time.
Remote control
does not work.
Make sure the batteries are properly inserted.
The batteries may already be drained out.
Replace batteries with new ones.
Remote control
code cannot be
detected by a
•
•
Purchase a separate learning remote control.
codes.
universal remote.
•
Make sure the video input cable is properly
connected to the correct terminal, and that the
correct input mode is enabled. To illustrate,
when a VGA cable is connected to display a
computer screen, the VGA input mode must
be enabled.
No picture
•
•
Verify that the antenna is properly connected
and that the preferred channel is enabled in
the channel list. Press and select
Channels/Channel List.
Adjust the display settings.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Corrective Action
•
•
•
Make sure the VGA cable is properly
connected to the LED TV’s VGA port.
No picture or the No
Signal message
appears when a
VGA cable is
Decrease the video resolution setting on the
computer and try again.
connected.
Adjust the display settings.
Picture is cut off or
appear in a sidebar
screen.
Press
to adjust the Aspect ratio.
•
Check your antenna connection. If necessary,
rotate the antenna and wait up to ten seconds
for a signal.
•
•
Reduce signal splitters and excessively long
cables.
Poor image quality
in TV mode (cutoff
picture, snowy
images).
Replace poor antenna cables and/or
connectors to improve signal quality.
•
•
Press
to adjust the Aspect ratio.
Adjust the Noise Reduction setting in Picture
menu.
•
•
In HDMI mode, make sure the external device
is compatible with the LED TV.
If any colors (red, green or blue) are missing,
check the video cable to make sure it is
securely connected. Loose or broken pins in
the cable connector could cause an improper
connection.
Wrong, abnormal or
missing colors
•
•
Adjust the Hue, Saturation and Color
Temperature settings in Picture menu.
Connect the TV to another computer and
check if the problem is with the computer
screen.
57
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Problem
Corrective Action
•
Make sure the audio input cable is properly
connected to the correct terminal, and that the
correct input mode is enabled.
•
•
•
The volume may be muted, press or Vol+ key
to turn on the volume.
Adjust the Bass, Treble, and Balance settings
in Audio menu.
No sound
If you are using the TV speakers, make sure
the TV Speakers option is set to On in Audio
menu.
•
If you are using an external audio device,
press and select Audio to make sure the TV
Speakers option is set to Off in Audio menu.
NOTES:
If the problem condition persists even after performing the
recommended corrective actions, contact us by:
•
•
Contacting the Westinghouse Customer Service at (800) 701-0680
or e-mail us at [email protected]
58
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
SPECIFICATIONS
Item
Specification
Model Name
EW32S5UW
Active Area
(Diagonal, mm)
697.685 (H) x 392.256 (V)
Resolution
1366 (H) x 768 (V)
3000:1
Contrast Ratio
(min)
Panel
Response Time
(min)
6.5ms(g-g)
Aspect Ratio
Display color
1.77 (16:9)
16.7M
•
•
•
•
•
•
•
HDMI x2
AV with R/L Audio x1
VGA with 3.5 mm mini jack x1
SPDIF Out x1
Audio/Video
Input/Output
Terminals
USB for service x1
Tuner x1
R/L Audio Line Out X1
Speaker Out
AV Timing
2X3W (2 channels)
480i/p, 720p, 1080i/p
640 x 400 @ 60Hz,
640 x 480 @ 75Hz,
800 x 600 @ 60Hz,
800 x 600 @ 75Hz,
1024 x 768 @ 60Hz,
1024 x 768 @ 75Hz,
1366 x 768 @ 60Hz
VGA Timing
Power Consumption
(Watts)
≤ 65W (@ 19V DC)
Power Consumption
(Standby, Watts)
<1W
59
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Item
Specification
With stand:
749.84mm x 503.57mm x 159.8mm
Dimensions
(WxHxD)
Physical
Without stand:
Specifications
749.84mm x 458.85mm x 52mm
Weight (Net)
6.19Kg
Weight (Gross) 8.6Kg
NOTES:
•
These product specifications are subject to change without user
notification.
•
Do not set your computer graphics card to exceed the unit’s refresh
rates; doing so may cause damage to the LED TV.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|