®
Model No. WCTL49300
Serial No.
Write the serial number in the
space above for future reference.
Serial
Number
Decal
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete cus-
tomer satisfaction. If you have
questions, or if there are missing
or damaged parts, please call:
1-888-936-4266
Mon.–Fri., 8h00 until 18h30 EST
(excluding holidays)
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website a
Download from Www.Somanuals.com. All Manuals Search And Download.
15. Do not perform exercises with the hand
weights at speeds faster than a walk. Using
weights and not holding the handrails may
compromise your ability to maintain your
balance. Exercises using weights should be
attempted only by experienced users.
10.) You must be able to safely lift 20 kg (45
lbs.) to raise, lower, or move the treadmill.
20. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
21. Inspect and tighten all parts of the treadmill
every three months.
16. The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
22. Never drop or insert any object into any
opening.
17. Never leave the treadmill unattended while it is
running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
23.
DANGER:
Always unplug the power
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures de-
scribed in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized ser-
vice representative only.
18. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
24. This treadmill is intended for in-home use
only. Do not use this treadmill in any com-
mercial, rental, or institutional setting.
19. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on pages 5 and 6, and HOW TO
FOLD AND MOVE THE TREADMILL on page
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decal shown below has been placed on your treadmill. If the
decal is missing or illegible, please call our Customer Service
Department, toll-free, to order a free replacement decal (see
ORDERING REPLACEMENT PARTS on the back cover of this
manual). Apply the decal in the location shown.
Note: Decal is shown at 38% of actual size.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the WESLO® CADENCE 215S
treadmill. The CADENCE 215S combines advanced
technology with innovative design to let you enjoy an
excellent form of cardiovascular exercise in the conve-
nience and privacy of your home. And when you’re not
exercising, the CADENCE 215S can be folded up, re-
quiring less than half the floor space of other treadmills.
at 1-888-936-4266, Monday through Friday, 8h00 until
18h30 EaStern time (excluding holidays). To help us
assist you, please note the product model number and
serial number before calling. The model number of the
treadmill is WCTL49300. The serial number can be
found on a decal attached to the treadmill (see the front
cover of this manual for the location).
For your benefit, read this manual carefully before
using the treadmill. If you have additional questions,
please call our Customer Service Department toll-free
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Water Bottle Holder
(Bottle not included)
Console
Weight Rack
Upright
Key/Clip
Storage Latch
Handrail
Walking Belt
Foot Rail
RIGHT SIDE
Circuit
Breaker
Power
Cord
Rear Roller
Adjustment Bolts
BACK
Incline Leg
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two people. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Assembly requires the included allen wrench
and your own phillips screwdriver
ters
, two adjustable wrenches
and wire cut-
.
Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a
small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This is a normal
condition and does not affect treadmill performance. If there is lubricant on top of the walking belt, simply wipe off
the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Handrail Bolt (91)–2
Extension Leg
Screw (53)–2
Screw (33)–6
Handrail Nut (15)–2
Handrail Washer (92)–2
Rack Washer (41)–2
Rack Bolt (89)–2
1. With the help of a second person, carefully raise the
Uprights (11) until the treadmill is in the position shown.
1
11
2. Insert one of the Extension Legs (34) into the treadmill
as shown. (Note: It may be helpful to tip the Uprights
[11] in the direction shown by the arrow as you insert
2
11
the Extension Leg.) Make sure that the Base Pad (40) is
on the indicated side of the Extension Leg. Attach the
Extension Leg with an Extension Leg Screw (53). Be
sure to push on the head of the Extension Leg
Screw while tightening it.
53
Attach the other Extension Leg (34) in the same way.
34
40
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the Weight Rack (90) to the Uprights (11) with the
two Rack Bolts (89) and Rack Washers (41). Note: If nec-
essary, spread the Uprights apart slightly to align the
holes in the Weight Rack with the holes in the Uprights.
3
41
89
90
41
89
Insert the Right Handrail (88) into the upper end of the
right Upright (11), with the lower end of the Handrail to the
side of the Extension Leg (34) as shown. Have a second
person hold the Right Handrail until step 4 is completed.
11
11
88
34
4. Attach the lower end of the Right Handrail (88) to the
Extension Leg (34) with a Handrail Bolt (91), a Handrail
Washer (92), and a Handrail Nut (15) as shown. Note: It
may be necessary to push on the lower end of the
Handrail to align the hole in the Handrail with the hole in
the Extension Leg.
4
88
34
91
Attach the Left Handrail to the left Extension Leg (not
shown) as described above.
15
92
5. Cut and remove the plastic tie on the right Upright (11).
5
11
Place the Console Base (46) on the right and left
Uprights (11) (only the right Upright is shown). Wrap the
indicated cable tie around the Wires (21) or pull the
Wires through the cable tie loop. Pull the cable tie tight
and cut off the end of the cable tie.
Cable
Tie
21
Connect the two indicated Wires (21) to the two connec-
tors in the Console Base (46). Important: Make sure
the Wires are fully inserted. WARNING: Do not dis-
connect or connect the Wires while the treadmill
power cord is plugged in. Loosely thread four Screws
(33) into the Uprights and the Console Base. After all
four Screws have been started, tighten the Screws
until they are snug; do not overtighten the Screws.
Connectors
33
Plastic Tie
46
90
6
6. Attach the Storage Latch (14) to the left Upright (11) with
two Screws (33). Be careful not to overtighten the
Screws.
11
33
14
79
Place the two 3-lb. Weights (79) in the center of the
Weight Rack (90). Next, place the 2-lb. Weights and the
1-lb. Weights (not shown) in the Weight Rack.
7. Make sure that all parts are tightened before you use the treadmill. Keep the included allen wrench in a
secure place. The allen wrench is used to adjust the walking belt (see page 13). To protect the floor or carpet,
place a mat under the treadmill.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
TM
THE PERFORMANT LUBE WALKING BELT
of electric shock. This product is equipped with a cord
having an equipment-grounding conductor and a
grounding plug. Plug the power cord into a surge
protector, and plug the surge protector into an ap-
propriate outlet that is properly installed and
grounded in accordance with all local codes and
ordinances.
Your treadmill features a walking belt coated with
PERFORMANT LUBETM, a high-performance lubricant.
IMPORTANT: Never apply silicone spray or other
substances to the walking belt or the walking plat-
form. They will deteriorate the walking belt and
cause excessive wear.
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge protector to a 2-pole recep-
tacle as shown in drawing 2 if a properly grounded out-
let is not available.
HOW TO PLUG IN THE POWER CORD
DANGER:
Improper connection of
the equipment-grounding conductor can re-
sult in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet installed
by a qualified electrician.
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can re-
sult from weather conditions or from other appliances
being turned on or off.
To decrease the pos-
sibility of your tread-
1
Grounded Outlet Box
mill being damaged,
always use a surge
protector (not in-
cluded) with your
treadmill.
Treadmill Power Cord
Grounding Pin
Grounding Plug
Grounding Plug
Grounding Pin
Surge protectors are
sold at most hardware
stores and department
stores. Use only a CUL-
listed surge protector,
rated at 15 amps, with a
14-gauge cord of five
feet or less in length.
Grounded Outlet
2
Grounded Outlet Box
Adapter
Grounding Pin
Grounding Plug
This product must be
grounded. If it should
malfunction or break
down, grounding pro-
vides a path of least re-
sistance for electric cur-
rent to reduce the risk
Surge Protector
Lug
Metal Screw
7
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGRAM OF THE CONSOLE
Displays
Incline Control
PulseSensor
Clip
Key
Speed Control
Battery Cover
CAUTION:
Before operating the
console, read the following precautions.
• Do not stand on the walking belt when turn-
ing on the power.
Battery
Cover Tab
• Always wear the clip (see the drawing
above) while using the treadmill. When the
key is removed from the console, the walk-
ing belt will stop.
Batteries
• Adjust the speed in small increments.
STEP-BY-STEP CONSOLE OPERATION
• To reduce the possibility of electric shock,
keep the console dry. Avoid spilling liquids
on the console. Use only a sealable water
bottle.
Before operating the console, make sure that the
power cord is properly plugged in. (See HOW TO
PLUG IN THE POWER CORD on page 7.)
Next, step onto the foot rails of the treadmill. Find the
clip attached to the key (see the drawing above), and
slide the clip onto the waistband of your clothing. Test
the clip by carefully taking a few steps backward
until the key is pulled from the console. If the key
is not pulled from the console, adjust the position
of the clip as needed.
BATTERY INSTALLATION
The console requires three "AA" batteries (not in-
cluded). Alkaline batteries are recommended. To in-
stall batteries, open the battery cover as shown at the
right. Press the batteries into the battery compartment,
with the negative (–) ends of the batteries touching the
springs. Close the battery cover, push up on the tab,
and then push the tab forward as shown. Be sure that
the tab locks into place.
Follow the steps on page 9 to operate the console.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BURNING on page 14.) Every seven seconds, the
display will change from one number to the other, as
indicated by the mode arrows. This display also
shows your pulse when the pulse sensor is used (see
step 4).
Insert the key fully into the power switch.
1
2
Note: Inserting the key
will not turn on the dis-
plays. The displays will
turn on when the
ON/RESET button is
pressed or when the
walking belt is started. If
you just installed batteries, the displays will already
be on.
The displays can be
reset, if desired, by
pressing the
ON/RESET button.
Measure your pulse, if desired.
4
Reset the console and start the walking belt.
To measure your
Pulse Sensor
pulse, stand on the
Slide the speed control down to
the RESET position. Note: Each
time the walking belt is
stopped, the speed control
must be moved to the RESET
position before the walking
belt can be restarted.
foot rails and place
your thumb on the
pulse sensor as
shown. The pulse
sensor is pressure ac-
tivated—fully press it
down. Do not press
too hard, or the cir-
culation in your
Next, slowly slide the speed
control until the walking belt be-
thumb will be re-
stricted, and your
pulse will not be de-
tected. Next, raise your thumb slightly until the
heart-shaped indicator in the pulse display flashes
steadily. Hold your thumb at this level. After a few
seconds, three dashes will appear in the display
and your pulse will be shown. Hold your thumb on
the sensor for another 15 seconds for the most ac-
curate reading.
gins to move at slow speed. Carefully step onto the
walking belt and begin exercising. Change the
speed of the walking belt as desired by moving the
speed control.
Pulse Indicator
To stop the walking belt, step onto the foot rails and
slide the speed control to the RESET position.
Follow your progress with the four displays.
3
TIME display—This
display shows the
elapsed time.
If the displayed pulse appears to be too high or too
low, or if your pulse is not displayed, lift your thumb
off the sensor and allow the display to reset. Press
down again on the sensor as described above. Make
sure that your thumb is positioned as shown, and
that you are applying the proper amount of pressure
to the pulse sensor. Try the sensor several times
until you become familiar with it. Remember to stand
still while measuring your pulse.
DISTANCE display—
This display shows the
distance that you have
walked or run, in miles.
5 mAidlljuasstdtheseirinecdl.ine of the tread-
SPEED display—This
display shows the speed
of the walking belt, in
miles per hour.
To change the incline, press the
top or bottom of the incline con-
trol until the desired incline level
is reached.
CALORIES/FAT
CALORIES/PULSE
display—This display
shows the approximate
numbers of calories and
fat calories you have
Turn off the power.
6
To turn off the power, simply wait for about four
minutes. If the walking belt is stationary and the
console buttons are not pressed for four minutes,
Mode Arrows
burned. (See FAT
9
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE HAND WEIGHTS
To exercise your upper body as you walk on the treadmill,
hold the ,45 kg (1-lb.) weights at your sides or press the
weights above your head. To increase the intensity of your
exercise, use the 1 kg (2-lb.) or 1,4 kg (3-lb.) weights. The
hand weights can be stored in the weight rack.
Weight
Rack
WARNING: Do not use the hand weights at speeds faster
than a walk. Using weights and not holding the handrails
may compromise your ability to maintain your balance.
Exercises using weights should be attempted only by
experienced users.
HOW TO SELECT KILOMETRES AND MILES
Console
Screws
The console can display distance and speed in either kilome-
tres or miles. To change the unit of measurement, first UN-
PLUG THE POWER CORD. Next, remove the six screws at-
taching the console to the console base. Lift the console a
few inches, being careful not to pull on the wires, and turn
the console over. Locate the small switch on the back of the
console. Move the switch upward or downward to select kilo-
metres or miles. Re-attach the console to the console base.
After changing the unit of measurement, remove one of
the batteries from the console for about five seconds and
then reinsert it. This will reset the console.
Console
Base
Screws
Switch
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, unplug the power cord.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
vertical position.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Move your right hand to the position shown and hold the
treadmill firmly. Raise the treadmill until the storage latch
closes over the catch. Make sure that the storage latch
is fully engaged over the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30° C (85° F).
Engaged
Storage
Latch
Catch
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the stor-
age position as described above. Make sure that the stor-
age latch is closed fully over the catch.
1. Hold the upper ends of the handrails. Place one foot on
the base as shown.
2. Tilt the treadmill back until it rolls freely on the front
wheels. Carefully move the treadmill to the desired loca-
tion. To reduce the risk of injury, use extreme caution
while moving the treadmill. Do not move the treadmill
over an uneven surface.
Base
Front Wheels
3. Place one foot on the base, and carefully lower the tread-
mill until it is resting in the storage position.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your right hand
as shown. Using your left thumb, press the storage latch
and hold it. Pivot the treadmill until the frame and foot rail
are past the storage latch.
Unlatched
Storage
Latch
2. Hold the treadmill firmly with both hands, and lower the
treadmill to the floor. Do not drop the treadmill frame to
the floor. To decrease the possibility of injury, bend
your legs and keep your back straight.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE AND TROUBLE-SHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please call our Customer Service Department toll-
free at 1-888-936-4266, Monday through Friday, 8h00 until 18h30 Eastern time (excluding holidays).
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge protector, and that the surge protector is
plugged into a properly grounded outlet. (See HOW TO PLUG IN THE POWER CORD on page
7.) Use only a CUL-listed surge protector, rated at 15 amps, with a 14-gauge cord of 1.5 m (5 ft.)
or less in length.
b. After the power cord has been plugged in, make sure that the key is fully inserted into the console.
c. Check the circuit breaker located on the treadmill
c
frame near the power cord. If the switch protrudes
as shown, the circuit breaker has tripped. To reset
the circuit breaker, wait for five minutes and then
press the switch back in.
Reset
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in.
c. Remove the key from the console. Reinsert the key fully into the console.
d. If the treadmill still will not run, please call our Customer Service Department, toll-free.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Check the batteries in the console. If the batteries need to be replaced, see “BATTERY
INSTALLATION” on page 8. Most problems are the result of drained batteries.
b. Remove the screws from the hood, and carefully re-
b
move the hood. Locate the Reed Switch (76) and the
Magnet (93) on the left side of the Pulley (77). Turn
3 mm
50
the Pulley until the Magnet is aligned with the Reed
Switch. Make sure that there is a gap of about 3
mm (1/8 in.) between the Magnet and the Reed
Switch. If necessary, loosen the Screw (17) and move
the Reed Switch slightly. Retighten the Screw. Re-at-
tach the hood, and run the treadmill for a few minutes
to check for a correct speed reading.
44
33
45
Top
View
12
Download from Www.Somanuals.com. All Manuals Search And Download.
4. SYMPTOM: THE WALKING BELT SLOWS WHEN WALKED ON
a. Use only a UL-listed surge suppressor, rated at 15 amps, with a 14-gauge cord of 1.5 m (5 ft.) or less in length.
b. If the walking belt is overtightened, treadmill performance may
b
decrease and the walking belt may be permanently damaged.
Remove the key and UNPLUG THE POWER CORD. Using the
allen wrench, turn both rear roller adjustment bolts counterclock-
wise, 1/4 of a turn. When the walking belt is properly tightened,
you should be able to lift each side of the walking belt 5 to 7 cm
(2 to 3 inches) off the walking platform. The center of the walking
belt should just touch the walking platform. Be careful to keep
the walking belt centered. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
5–7 cm
Rear Roller Adjustment Bolts
c. If the walking belt still slows when walked on, please call our Customer Service Department, toll-free.
5. SYMPTOM: THE WALKING BELT IS OFF-CENTER
a. If the walking belt has shifted to the left, first remove the key
a
and UNPLUG THE POWER CORD. Using the allen wrench,
turn the left rear roller adjustment bolt clockwise, and the right
bolt counterclockwise, 1/4 of a turn each. Be careful not to over-
tighten the walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until the walking
belt is centered.
b. If the walking belt has shifted to the right, first remove the
b
key and UNPLUG THE POWER CORD. Using the allen wrench,
turn the left rear roller adjustment bolt counterclockwise, and the
right bolt clockwise, 1/4 of a turn each. Be careful not to over-
tighten the walking belt. Plug in the power cord, insert the key
and run the treadmill for a few minutes. Repeat until the walking
belt is centered.
c. If the walking belt slips when walked on, first remove the key
c
and UNPLUG THE POWER CORD. Using the allen wrench,
turn both rear roller adjustment bolts clockwise, 1/4 of a turn.
When the walking belt is correctly tightened, you should be able
to lift each side of the walking belt 5 to 7 cm (2 to 3 inches) off
the walking platform. Be careful to keep the walking belt cen-
tered. Plug in the power cord, insert the key and run the tread-
mill for a few minutes. Repeat until the walking belt is properly
tightened.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
accessible carbohydrate calories for energy. Only after
the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn fat,
adjust the speed and incline of the treadmill until your
heart rate is near one of the lower two numbers in your
training zone.
WARNING:
Before beginning
this or any exercise program, consult your
physician. This is especially important for in-
dividuals over the age of 35 or individuals
with pre-existing health problems.
Aerobic Exercise
The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
The following guidelines will help you to plan your ex-
ercise program. For more detailed exercise informa-
tion, obtain a reputable book or consult your physician.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Each workout should include the following three parts:
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the desired
results is to exercise with the proper intensity. The
proper intensity level can be found by using your heart
rate as a guide. The chart below shows recommended
heart rates for fat burning and aerobic exercise.
A Warm-up
Start each workout with 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases your
body temperature, heart rate, and circulation in prepa-
ration for exercise.
Training Zone Exercise
After warming up, increase the intensity of your exer-
cise until your heart rate is in your training zone for 20
to 60 minutes. (During the first few weeks of your exer-
cise program, do not keep your heart rate in your train-
ing zone for longer than 20 minutes.)
A Cool-Down
Finish each workout with 5 to 10 minutes of stretching
to cool down. This will increase the flexibility of your
muscles and will help to prevent post-exercise prob-
lems.
To find the proper heart rate for you, first find your age
on the left side of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers to
the right of your age. The three numbers are your
“training zone.” The lower two numbers are recom-
mended heart rates for fat burning; the higher number
is the recommended heart rate for aerobic exercise.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each week
if desired. The key to success is to make exercise a
regular and enjoyable part of your everyday life.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easily
14
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-888-936-4266, Monday
through Friday, 8h00 until 18h30 Eastern time (excluding holidays). To help us assist you, please be prepared to
give the following information when calling:
• The MODEL NUMBER of the product (WCTL49300)
• The NAME of the product (WESLO CADENCE® 215S treadmill)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED DRAW-
ING in the center of this manual).
PLACE
STAMP
HERE
ICON of Canada Inc.
900 de l’Industrie
St-Jérôme, Québec
Canada, J7Y 4B8
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS EXPLODED DRAWING
AND PART LIST FROM THE MANUAL
Save this EXPLODED DRAWING and PART LIST for future reference.
4
3
Note: Specifications are subject to change without notice. For information about
ordering replacement parts, see the back cover of the User’s Manual.
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ICON OF/DU CANADA INC., (ICON), warrants this product to be free from defects in workmanship and material,
under normal use and service conditions, for a period of 1 year from the date of purchase. This warranty extends
only to the original purchaser. ICON's obligation under this warranty is limited to replacing or repairing, at ICON's
option, the product at one of its authorized service centers. All products for which warranty claim is made must be
received by ICON at one of its authorized service centers with all freight and other transportation charges pre-
paid, accompanied by sufficient proof of purchase. All returns must be pre-authorized by ICON. This warranty
does not extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center, to products used
for commercial or rental purposes, or to products used as store display models. No other warranty beyond that
specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property, loss
of revenues or profits, loss of enjoyment or use, costs of removal, installation or other consequential damages of
whatsoever nature. Some provinces do not allow the exclusion or limitation of incidental or consequential dam-
ages. Accordingly, the above limitation may not apply to you. The warranty extended hereunder is in lieu of any
and all other warranties and any implied warranties of merchantability or fitness for a particular purpose is limited
in its scope and duration to the terms set forth herein. Some provinces do not allow limitations on how long an
implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from province to province
or so specified by the retailer of your equipment.
ICON OF/DU CANADA, 900 de l’Industrie, St. Jerôme, QC J7Y 4B8
®
™
o f / d u C a n a d a I n c .
PRODUCT WARRANTY REGISTRATION
IMPORTANT: MAIL WITHIN 14 DAYS OF PURCHASE
NAME:
ADDRESS:
COUNTY:
MODEL NO.
RETAILER NAME:
PHONE:
POSTCODE:
RETAILER ADDRESS:
SERIAL NO.
PURCHASE
1) Primary user(s) of product:
8) Did you consider purchasing fitness equipment from another
manufacturer?
J Male
J Female
J Family
J 55–64
J No
J Yes
2) Age of primary user:
J 0–24
What other Manufacturer?
J 35–44
J 45–54
J 25–34
J 65 and over
9) Based on your impression of what you have purchased,
would you buy another ICON product?
3) Annual household income:
J Yes
J No
J No Opinion
J 0–9,999
J 10,000–14,999
J 15,000–19,999
J 20,000+
If not, what other brand name equipment would you purchase?
4) How many times a week do you exercise?
10) What other type of exercise equipment do you own?
J Less than 3 times J 3 times or more
J Bicycle
J Exercise Cycle J Treadmill
J Weight Bench J Stepper
J Other
J Home Gym
J Cardio Glide
5) Have you ever purchased an ICON product before?
J Yes J No
11) Which type of magazines do you read regularly?
6) Where did you first see or hear about ICON products?
J Sports
J Fitness
J Motoring
J General
J Magazine
J Newspaper Ad
J Other
J Friend/relative
J Store
J Business
J Computer
12) Do you wish to be sent further bulletins about ICON products?
J Yes J No
7) What was the primary reason for purchasing this ICON product?
J Store Employee J Television Ads J Colour
J Electronic Features J Magazine Ads J Price
THANK YOU FOR YOUR TIME
© 1997 ICON of Canada, Inc. Printed in Canada
J Product Design
J Other Features
J Product Innovation
WESLO is a registered trademark of ICON Health & Fitness, Inc.
Part No. 175016 R1102A Printed in Canada © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WCTL49300
R1102A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
2
2
1
1
1
1
1
1
1
1
4
1
2
7
6
1
1
1
1
1
1
1
8
1
1
1
1
1
4
1
13
2
1
2
2
4
11
4
2
3
1
1
1
1
2
4
4
1
Left Handrail
Key/Clip
Incline Leg Pivot Bolt
Battery Cover
Left Foot Rail
Lift Motor
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85*
86
87
88
89
90
91
92
#
1
2
2
1
1
1
2
2
1
1
2
2
3
1
2
4
1
1
1
21
1
1
4
1
1
2
2
2
2
2
1
1
2
1
2
1
2
1
2
1
2
2
1
1
1
1
Front Roller Adj. Bolt
Incline Wheel
Extension Leg Screw
Power Cord
Power Cord Grommet
Circuit Breaker
Frame Pivot Washer
Frame Pivot Bolt
Latch Decal
Motor Belly Pan
Cable Tie Clamp
Rear Platform Screw
Releasable Tie
Choke
Belt Guide
Belly Pan Fastener
Walking Belt
Walking Platform
Belly Pan
Rear Hood Screw
Incline Wire Harness
Upright Grommet
Isolator Screw
Allen Wrench
Frame
1 lbs Weight
Incline Wheel Bolt
2 lbs Weight
3 lbs Weight
Front Hood Screw
Ground Wire
Incline Leg
Rear Roller Adj. Bolt
Rear Endcap
Extension Leg Assembly
Right Foot Rail
Belly Pan Screw
Right Handrail
Rack Bolt
Weight Rack
Handrail Bolt
Handrail Washer
8” White Wire, Pigtail
8” Blue Wire, M/F
8” Red Wire, M/F
User’s Manual
Rear Roller
Speed Potentiometer
Speed Control Knob
Console Assembly
Upright
9
10*
11
12
13
14
15
16
17
18
19
20*
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Motor Belt
Belt Guide Screw
Storage Latch
Handrail Nut
8” Cable Tie
Incline Leg Pivot Nut
Pulley/Flywheel/Fan
Motor
Motor/Pulley/Flywheel/Fan
Wire Harness
Motor Pivot Nut
Motor Hood
Hood Shield
Small Screw
Controller
Motor Swivel Bolt
Motor Tension Nut
Motor Tension Star Washer
Motor Tension Washer
Motor Tension Bolt
Incline Stop Bracket
Screw
Extension Leg
Hood Shield Plug
Wheel Bolt
Wheel
Wheel Nut/Lift Nut
Washer
Base Pad
Rack Washer
Latch Catch
Reed Switch Clip
Reed Switch
Magnet
Console Base
Frame Spacer
Platform Screw
Isolator
#
#
#
* Includes all parts shown in the box
# These parts are not illustrated
Front Roller/Pulley
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|