Model No. WEBE08910
Serial No.
Write the serial number in the
space above for reference.
USER’S MANUAL
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satisfac-
tion through direct assistance
from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1.Read all instructions in this manual be9f.oDroe not use
a
barbell that is longer than six
using the weight bench. Use the weight
bench only as described in this manual.
feet with the weight bench.
10.Always exercise with a partner. When you
2.It is the responsibility of the owner to aernespuererforming bench press exercises, your
that all users of the weight bench are ade-
quately informed of all precautions.
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
3.The weight bench is intended for hom1e1.Kueseep hands and feet away from moving parts.
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
12.Always be sure there is an equal amount of
weight on each side of your barbell when
level syuoru- are using it. Always keep some weight
on both ends of the barbell when adding or
removing weights to prevent the barbell from
tipping.
4.Use the weight bench only on
face. Cover the floor beneath the weight
bench to protect the floor.
a
5.Make sure all parts are properly tightened
each time you use the weight bench. Replace 13.Always remove the curl post from the front
any worn parts immediately.
leg before performing leg curl or leg exten-
sion exercises with the leg lever.
6.Keep children under 12 and pets away from
the weight bench at all times. 14. When you are using the leg lever, place a
barbell with the same amount of weight on
7.Always wear athletic shoes for foot protect-he weight rests to balance the bench.
tion while exercising.
15.When using the backrest in an inclined posi-
8.The weight bench is designed to support tioan, make sure that the support rod is
maximum user weight of 250 pounds and a
maximum total weight of 460 pounds. Do not
place more than 210 pounds, including a
weight bar and weights, on the weight rests.
Do not place more than 130 pounds on the
leg lever. Note: The weight bench does not
include a barbell or weights.
inserted completely through both uprights,
and that the support rod is turned to the
locked position.
16.If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® 525
weight bench. The weight bench is designed to be
used with your own weight set (not included) to help
you develop every major muscle group of the body.
Whether your goal is a shapely figure, dramatic
increase in muscle size and strength, or a healthier
cardiovascular system, the weight bench will help you
achieve the specific results you want.
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE08910. The serial number can be
found on a decal attached to the weight bench (see
the front cover of this manual).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department
Weight Rests
Upright
Backrest
Curl Pad
Support Rod
Leg Lever
Seat
Weight Tube
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
This chart is provided to help you identify the small parts used in assembly. The number in parenthesis below
each part refers to the key number of the part, from the PART LIST on page 14 of this manual. Important:
Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts
bags, check to see if it has been pre-assembled.
M8 x 65mm Bolt (22)
M8 Washer (29)
M6 Washer (25)
M10 x 60mm Bolt (27)
M8 x 55mm Bolt (34)
M8 x 50mm Bolt (35)
M10 Nylon Locknut (30)
M8 Nylon Locknut (23)
M8 x 40mm Carriage Bolt (26)
M6 x 38mm Screw (24)
M6 x 16mm Screw (21)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by anyone. However, it is important to
realize that the versatile weight bench has many
parts and that the assembly process will take
time. Most people find that by setting aside plen-
ty of time, assembly will go smoothly.
• For help identifying small parts, use the PART
IDENTIFICATION CHART on page 5.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• One Phillips screwdriver
• Assembly requires two people.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
1. Before assembling this product, be sure that
you have read and understand the information
in the box above.
1
3
Slide the Small Crossbar (3) into the Large
Crossbar (2), with the decal on top. Note: the
crossbar can be adjusted for use with either a
mid-width barbell or an olympic barbell.For a
mid-width barbell, align the indicated set of
holes on the Crossbars. For an olympic bar-
bell, align the inner set of holes.
2
22
34
Decal
4
Attach the Frame (4) to the Crossbars (2, 3) with
two M8 x 65mm Bolts (22), two M8 x 55mm Bolts
(34), and four M8 Nylon Locknuts (23). Do not
tighten the Nylon Locknuts yet.
23
23
2
26
14
2. Insert a 38mm Square Inner Cap (14) into the
Front Leg (5).
4
Attach the Front Leg (5) to the Frame (4) with two
M8 x 40mm Carriage Bolts (26), two M8 Washers
(29), and two M8 Nylon Locknuts (23). Do not
tighten the Nylon Locknuts yet.
29
23
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the Crossbars (2, 3) to the Uprights (1)
with four M8 x 65mm Bolts (22), two Support
Plates (12), and four M8 Nylon Locknuts (23). Do
not tighten the Nylon Locknuts yet. Note the
position of the name decal and make sure the
Uprights are oriented as shown.
3
1
12
1
23
22
Name
Decal
3
22
12
2
23
4. Press a 25.4mm Round Inner Cap (19) into the
indicated end of the Weight Tube (37). Slide the
Weight Tube through the Leg Lever (6) and attach
it with an M8 x 50mm Bolt (35), two M8 Washers
(29), a Sleeve (36), and an M8 Nylon Locknut
(23). Press a 25.4mm Angle Cap (20) onto the
other end of the Weight Tube.
4
Lubricate
27
14
6
30
20
23
14
Tap three 38mm Square Inner Caps (14) into the
Leg Lever (6).
5
29
37
Lubricate the M10 x 60mm Bolt (27). Attach the
Leg Lever (6) to the Front Leg (5) with the Bolt
and an M10 Nylon Locknut (30). Do not over-
tighten the Nylon Locknut; the Leg Lever must
be able to pivot freely.
19
36
14
29
35
5. Press two 19mm Round Inner Caps (16) into
each Pad Tube (17). Slide the Pad Tubes through
the holes in the Leg Lever (6). Slide a Foam Pad
(18) onto each side of the two Pad Tubes.
5
18
6
16
17
16
16
17
16
18
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press four 25.4mm Square Inner Caps (15) into
the indicated ends of each Backrest Tube (8).
6
9
Attach the Backrest Tubes (8) to the Backrest (9)
with three M6 x 38mm Screws (24) and three M6
Washers (25). Do not tighten the Screws yet.
15
15
25
24
25
25
24
8
24
8
15
15
7. Press a 25.4mm Round Inner Cap (19) into each
end of the Support Rod (13).
7
8
Insert the end of the Support Rod (13) without the
locking clip through the Uprights (1). Rotate the
locking clip into place around the Upright.
8
1
See the inset drawing. With the help of a sec-
ond person, slide the indicated ends of the
Backrest Tubes (8) onto the welded axle on the
Frame (4).
Welded Axle
4
19
9
Attach the left Backrest Tube (8) to the Backrest
(9) with a fourth M6 x 38mm Screw (24) and M6
Washer (25). Tighten all four Screws in the
Backrest.
1
13
Rest the Backrest (9) on the Support Rod (13).
Tighten the M8 Nylon Locknuts (23) used in
steps 1–3.
25
19
8
24
8. Attach the Seat (10) to the brackets on the Frame
(4) with four M6 x 16mm Screws (21).
8
10
4
21
21
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Attach the Curl Pad (11) to the Curl Post (7) with
two M6 x 16mm Screws (21).
9
11
7
21
10. Make sure that all parts are properly tightened before you use the weight bench. The use of all
remaining parts will be explained in ADJUSTMENTS, beginning on the following page.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
The weight bench is designed to be used with your own weight set (not included). The steps below explain how
the weight bench can be adjusted. See EXERCISE GUIDELINES on page 12 for important exercise information
and refer to the accompanying exercise guide to see the correct form for each exercise. Refer also to the
exercise information accompanying your weight set (not included) for additional exercises.
Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
The Backrest (9) can be used in a decline position, a
level position, or three incline positions. To use the
Backrest in the decline position, remove the Support
1
Rod (13) and lay the Backrest on the Crossbar (2).
13
9
To use the Backrest (9) in the level position, lift the
Backrest and insert the Support Rod (13) through the
bottom set of holes in the Uprights (1). Rotate the
locking clip into place around the Upright.
1
To use the Backrest (9) in an incline position, lift the
Backrest and insert the Support Rod (13) through one
of the top three sets of holes in the Uprights (1).
Rotate the locking clip into place around the Upright.
WARNING:
When using the
2
Backrest (9) in a level or incline position, insert
the Support Rod (13) completely through both
Uprights (1) and turn it to the locked position.
ATTACHING WEIGHTS TO THE LEG LEVER
6
To use the Leg Lever (6), slide the desired weights
(not included) onto the weight tube.
To use Olympic weights, press the two Adapter
Bushings (32) into the ends of the Weight Tube
Adapter (31). Slide the Weight Tube Adapter onto the
Weight Tube (37) on the Leg Lever (6). Insert the Pin
(33) into the Weight Tube.
33
32
31
32
37
Weight
WARNING:
Do not place more
than 50 pounds on the Leg Lever (6).
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE CURL POST
For some exercises, the Curl Pad (11) must be
attached to the weight bench.
Insert the Curl Post (7) into the indicated hole in the
Front Leg (5). Align the holes in the Front Leg and the
Curl Post. Secure the Curl Post with the Adjustment
Knob (28). Make sure that you fully tighten the
Adjustment Knob.
11
7
Note: When the Curl Pad (11) is not in use, the
38mm Square Inner Cap (14) should be inserted
into the Front Leg (5).
14
28
5
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will continually adapt and grow as you progres-
sively increase the intensity of your exercise. You can
adjust the intensity level of an individual exercise in
two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
ing it during the first few months of your exercise pro-
gram. You should progress at your own pace and be
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
WARMING UP
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
Begin each workout with 5 to 10 minutes of stretching
your limits and select the amount of weight that is right and light exercise to warm up. Warming up prepares
for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of weight.
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a mod- Each workout should include 6 to 10 different exercis-
erate percentage of their capacity. Select a moderate
amount of weight and increase the number of repeti-
tions in each set. Complete as many sets of 15 to 20
repetitions as possible without discomfort. Rest for 1
minute after each set. Work your muscles by complet-
ing more sets rather than by using high amounts of
weight.
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise, and
Cross Training
Cross training is an efficient way to get a complete and moving only the appropriate parts of the body.
well-balanced fitness program. An example of a bal-
anced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
13 to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body, plus devel- during the exertion stage of each repetition and inhale
op your heart and lungs. during the return stroke. Never hold your breath.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. List
the date, the exercises performed, the weight used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at
the end of every month. Remember, the key to
achieving the greatest results is to make exercise a
regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
N
O
P
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
A
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
C
D
E
Q
R
S
F
L
T
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
G
M
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
H
I
U
V
Q. Triceps (back of arm)
J
K
W
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WEBE08910
R1002A
Key No.Qty.
Description
Key No.Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2
1
1
1
1
1
1
2
1
1
1
2
1
4
4
4
2
4
3
1
Upright
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
#
6
6
11
4
4
2
1
1
4
1
1
2
1
2
1
1
1
1
1
M6 x 16mm Screw
M8 x 65mm Bolt
M8 Nylon Locknut
M6 x 38mm Screw
M6 Washer
M8 x 40mm Carriage Bolt
M10 x 60mm Bolt
Adjustment Knob
M8 Washer
M10 Nylon Locknut
Weight Tube Adapter
Adapter Bushing
Pin
M8 x 55mm Bolt
M8 x 50mm Bolt
Sleeve
Large Crossbar
Small Crossbar
Frame
Front Leg
Leg Lever
Curl Post
Backrest Tube
Backrest
Seat
Curl Pad
Support Plate
Support Rod
38mm Square Inner Cap
25.4mm Square Inner Cap
19mm Round Inner Cap
Pad Tube
Foam Pad
25.4mm Round Inner Cap
25.4mm Angle Cap
Weight Tube
User’s Manual
Exercise Guide
#
“#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover of
this manual for information on ordering replacement parts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WEBE08910
R1002A
1
19
12
23
22
13
19
22
3
1
2
22
11
10
12
22
22
34
23
21
14
7
34
4
26
27
14
9
23
23
18
21
15
21
29
6
30
20
36
23
23
28
14
19
29
25
8
5
25
33
29
8
14
16
24
37
15
35
25
25
24
32
31
17
32
16
18
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
• The MODEL NUMBER of the product (WEBE08910)
• The NAME of the product (WEIDER® 525 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING on pages 14 and 15 of this manual).
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and mate-
rial, under normal use and service conditions, for a period of ninety (90) days from the date of purchase. This
warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to replacing
or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which
warranty claims are made must be pre-authorized by ICON. This warranty does not extend to any product or
damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage
or repairs not provided by an ICON authorized service center; products used for commercial or rental pur-
poses; or products used as store display models. No other warranty beyond that specifically set forth above
is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection
with the use or performance of the product or damages with respect to any economic loss, loss of property,
loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other consequential
damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or conse-
quential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of mer-
chantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein.
Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above limitation
may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 176984 R1002A
Printed in USA © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|