Model No. 831.15609.0
Serial No.
Write the serial number in the
space above for reference.
WEIGHT BENCH EXERCISER
User’s Manual
Serial Number Decal (under seat)
• Assembly
• Adjustments
• Part List and Drawing
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precau-
tions before using the weight bench.
1. Read all instructions in this manual and all
warnings on the weight bench before using
the weight bench. Use the weight bench only
as described in this manual.
10. The weight bench is designed to support a
maximum user weight of 300 pounds, and a
maximum total weight of 510 pounds. Do not
place more than 210 pounds, including a bar-
bell and weights, on the weight rests. Do not
place more than 130 pounds on the leg lever
or weight carriage. Note: The weight bench
does not include a barbell or weights.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
11. Do not sit on the top end of the backrest;
this will cause the weight bench to tip.
12. Always make sure there is an equal amount
of weight on each side of your barbell when
you are using it. Always keep some weight
on both ends of the barbell when adding or
removing weights to prevent the barbell from
tipping.
4. Keep the weight bench indoors, away from
moisture and dust. Place the weight bench
on a level surface, with a mat beneath it to
protect the floor or carpet. Make sure that
there is enough clearance around the weight
bench to mount, dismount, and use the
weight bench.
13. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
5. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
14. When you put weight on the weight rests,
make sure you put at least ten pounds on the
leg lever to balance the weight bench.
6. Keep children under 12 and pets away from
the weight bench at all times.
7. Keep hands and feet away from moving parts. 15. Make sure that the adjustment pin and
weight rest knobs are inserted completely
8. Always wear athletic shoes for foot protec-
tion while exercising.
and tightened into the uprights before begin-
ning any exercise.
9. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
16. Always remove the curl post and lat tower
from the front leg before using the leg lever.
17. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. Sears assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® PRO
reading this manual, call 1-800-4-MY-HOME®
260 weight bench. The weight bench offers an impres- (1-800-469-4663). To help us assist you, please note
sive array of weight stations designed to develop
every major muscle group of the body. Whether your
goal is to tone your body, build dramatic muscle size
and strength, or improve your cardiovascular system,
the weight bench will help you to achieve the specific
results you want.
the product model number and serial number before
calling. The model number is 831.15609.0. The serial
number can be found on a decal attached to the
weight bench (see the front cover of this manual for
the location of the decal).
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have questions after
ASSEMBLED DIMENSIONS:
Height: 79 in. / 201 cm
Width: 40 in. / 102 cm
Depth: 70 in. / 178 cm
Lat Bar
Lat Tower
Weight Rest
Backrest
Weight Rest Knob
Upright
Weight Carriage
Storage Tube
Seat
Leg Lever
Backrest
Bracket
Weight Tube
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the weight bench can be assembled suc-
cessfully by almost anyone. However, the weight
bench has many parts and the assembly
process will take time. By setting aside plenty of
time, assembly will go smoothly.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
The included grease, and the following tools
(not included) may be required for assembly:
Before beginning assembly, carefully read the
following information and instructions:
• Two adjustable wrenches
• One rubber mallet
• Assembly requires two people.
• One standard screwdriver
• Because of its weight and size, the weight bench
should be assembled in the location where it will
be used. Make sure that there is enough clear-
ance to walk around the weight bench as you
assemble it.
• One Phillips screwdriver
• Clear tape or masking tape, and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
1.
1
Before beginning assembly, make sure you
understand the information in the box
above. For help identifying small parts, use
the PART IDENTIFICATION CHART in the
center of this manual.
5
4
7
Lift the Weight Rest (7) in the Left Upright (6) and
secure it with a Weight Rest Knob (23).
Name
Decal
23
43
18
Orient the Crossbar (4) as shown. Attach the
Crossbar to the Left Upright (6) with two Joint
Plates (18), four M10 x 75mm Bolts (42), and four
M10 Nylon Locknuts (43). Do not tighten the
Locknuts.
43
42
Attach the Crossbar (4) to the Right Upright
(5) in the same manner.
6
18
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the Bench Frame (1) to the Front Leg (2)
with two M10 x 65mm Bolts (40), two M10
Washers (44), and two M10 Nylon Locknuts (43).
Do not tighten the Locknuts.
2
40
1
44
40
43
2
3. Attach the Bench Frame (1) to the Crossbar (4)
with two M10 x 81mm Bolts (41) and two M10
Nylon Locknuts (43).
3
4
5
4
Tighten the M10 Nylon Locknuts (43) used in
steps 1 through 3.
43
41
41
43
1
4. Attach the Weight Tube (16) inside the Leg Lever
(3) with an M8 x 58mm Bolt (52), two M8
Washers (56), a 10mm Spacer (32), and an M8
Nylon Locknut (55).
2
3
Press the 25mm Round Angled Cap (28) onto the
Weight Tube (16).
Grease
55
56
28
54
32
Grease an M10 x 68mm Bolt (54). Attach the Leg
Lever (3) with the Bolt and an M10 Nylon Locknut
(43). Do not overtighten the Locknut; the Leg
Lever must be able to pivot easily.
56
16
52
48
5. Orient the Backrest Frames (12) with the indicat-
ed holes closer to the bottom. Attach the Backrest
Frames to the Backrest Bracket (10) with four M6
x 40mm Bolts (49), four M6 Washers (48), and
four M6 Nylon Locknuts (51). Do not tighten the
Locknuts.
49
Holes
48
48
49
48
12
51
51
10
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Orient the Backrest (13) as shown. Attach the
Backrest to the Backrest Frames (12) with four
M6 x 40mm Bolts (49) and four M6 Washers (48).
Do not tighten the Bolts.
6
13
Wide
End
12
48
12
48
48
49
49
7. Insert the Backrest Bracket (10) through the
Bench Frame (1).
7
Grease an M10 x 168mm Bolt (50). Attach the
Backrest Frames (12) to the Bench Frame (1)
with the Bolt and an M10 Nylon Locknut (43). Do
not overtighten the Locknut; the Backrest
Frames must be able to pivot easily.
12
43
Attach the Adjustment Pin (25) to the Bench
Frame (1) with an M4 x 16mm Screw (45).
Engage the Pin into the Bench Frame and the
Backrest Bracket (10).
10
25
Tighten the M6 x 40mm Bolts (49) and M6
Nylon Locknuts (51) used in steps 5 and 6.
45
1
50
8. Orient the Seat (14) as shown. Attach the Seat to
the Bench Frame (1) with four M6 x 16mm
Screws (39).
8
14
Wide
End
1
39
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Insert a Pad Tube (19) into the Leg Lever (3).
Slide two Foam Pads (20) onto the Pad Tube.
9
2
3
19
19
Repeat this step with the other two Pad Tubes
(19) and the Leg Lever (3) and Front Leg (2).
20
20
19
10. Attach the Curl Pad (15) to the Curl Post (11) with
two M6 x 16mm Screws (39).
10
15
11
39
11. Route the Lat Cable (35) through the Lat Tower
(8) and over the Pulley (38). Make sure that the
Cable is under the lat rest bar. Attach the
Pulley inside the Lat Tower with an M10 x 60mm
Bolt (47), two M10 Washers (44), two 10mm
Large Spacers (31), and an M10 Nylon Locknut
(43).
11
Lat Rest
Bar
43
44
31
35
44
38
31
47
8
12. Insert an M10 x 19mm Bolt (53) into the bracket
on the Weight Carriage (9).
12
8
Slide the Weight Carriage (9) onto the Lat Tower
(8). Make sure the bracket on the Weight
Carriage and the lat rest on the Lat Tower (see
step 11) are on opposite sides of the Lat
Tower. Attach the Lat Cable (35) to the M10 x
19mm Bolt (53) with an M10 Nylon Locknut (43).
35
43
53
Bracket
13. Make sure that all parts are properly tightened
before the weight bench is used. The use of all
remaining parts will be explained in ADJUST-
MENTS, beginning on the following page.
9
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 11 for impor-
tant information about how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
The Backrest (13) can be used in a decline position,
a level position, or an incline position. To use the
Backrest in the decline position, remove the
Adjustment Pin (25) and lay the Backrest on the
Crossbar (4).
13
4
To use the Backrest (13) in the level or inclined posi-
tion, lift the Backrest and insert the Adjustment Pin
(25) through the Bench Frame (1) and a hole in the
Backrest Bracket (10).
1
25
Adjustment
Holes
10
ADDING WEIGHT
Weight
To use the Weight Carriage (9) or the Leg Lever (3),
slide the desired weights (not included) onto the
Weight Carriage or the Weight Tube (16). Secure the
weights on the Weight Carriage with the Spring Clips
(36).
9
3
WARNING:
Do not place more than
150 pounds on the Weight Carriage (9) or
Weight Tube (16).
36
16
Unused weights can be stored on the tubes on the
Uprights (not shown).
ADJUSTING THE WEIGHT RESTS
7
5
To change the height of the Weight Rests (7), remove
the Weight Rest Knobs (23). Position the Weight
Rests to the desired height in the Uprights (5, 6) and
secure them with the Weight Rest Knobs.
23
7
WARNING:
Always set both Weight
Rests (7) at the same height. Make sure the
Weight Rest Knobs (23) are inserted into both
the Upright (5 and 6) and the Weight Rest.
6
23
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE CURL PAD
For some exercises, the Curl Pad (15) must be
attached to the weight bench. Remove the 45mm
Thick Square Inner Cap (57) from the Front Leg (2).
8
Insert the Curl Post (11) into the Front Leg (2). Align
one of the adjustment holes in the Curl Post with the
adjustment hole in the Front Leg. Fully tighten the
Curl Knob (34) into the Front Leg.
15
The Lat Tower (8) can be attached in the same way.
Note: When the Curl Pad (15) or Lat Tower (8) is not
in use, the 45mm Thick Square Inner Cap (57) should
be inserted into the Front Leg (2).
11
57
34
2
ATTACHING THE LAT BAR
Attach the Lat Bar (17) to the Lat Cable (35) with a
Cable Clip (37). Remove the Lat Bar when performing
an exercise that does not require it.
35
37
17
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
To increase the size and strength of your muscles,
Determining the exact length of time for each workout,
as well as the number of repetitions or sets completed,
push them close to their maximum capacity. Your mus- is an individual matter. It is important to avoid overdo-
cles will adapt and grow as you progressively increase ing it during the first few months of your exercise pro-
the intensity of your exercise. You can adjust the inten- gram. You should progress at your own pace and be
sity level of an individual exercise in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
sensitive to your body’s signals. If you experience pain
or dizziness at any time while exercising, stop immedi-
ately and begin cooling down. Find out what is wrong
before continuing. Remember that adequate rest and a
proper diet are important factors in any exercise pro-
gram.
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
WARMING UP
your limits and select the amount of weight that is right Begin each workout with 5 to 10 minutes of stretching
for you. Begin with 3 sets of 8 repetitions for each
exercise you perform. Rest for 3 minutes after each
set. When you can complete 3 sets of 12 repetitions
without difficulty, increase the amount of weight.
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
Toning
WORKING OUT
You can tone your muscles by pushing them to a mod-
erate percentage of their capacity. Select a moderate
amount of weight and increase the number of repeti-
tions in each set. Complete as many sets of 15 to 20
repetitions as possible without discomfort. Rest for 1
minute after each set. Work your muscles by complet-
ing more sets rather than by using high amounts of
weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
Cross Training
Cross training is an efficient way to get a complete and through the full range of motion for each exercise, and
well-balanced fitness program. An example of a bal-
anced program is:
• Plan strength training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
running on a treadmill or riding on an exercise cycle
or an elliptical exerciser, on Tuesday and Thursday.
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on the
next page to find the names of the muscles.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
The combination of strength training and aerobic exer- return stage. Proper breathing is important. Exhale
cise will reshape and strengthen your body, plus devel- during the exertion stage of each repetition and inhale
op your heart and lungs.
during the return stroke. Never hold your breath.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
slowly as you stretch and do not bounce. Ease into
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on pages 13 and 14 of this manual can be pho-
tocopied and used to schedule and record your work-
outs. List the date, the exercises performed, the resist-
ance used, and the numbers of sets and repetitions
completed. Record your weight and key body meas-
urements at the end of every month. Remember, the
key to achieving the greatest results is to make exer-
cise a regular and enjoyable part of your everyday life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
MUSCLE CHART
O
A. Sternomastoid (neck)
A
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
P
L
Q
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
R
S
C
D
E
T
F
M
N
U
L. Anterior Deltoid (shoulder)
M. Rectus Abdominus (stomach)
N. Adductor (inner thigh)
G
H
I
V
O. Trapezius (upper back)
P. Rhomboideus (upper back)
Q. Posterior Deltoid (shoulder)
R. Triceps (back of arm)
S. Latissimus Dorsi (mid back)
T. Spinae Erectors (lower back)
U. Gluteus Medius (hip)
W
X
J
K
V. Gluteus Maximus (buttocks)
W. Hamstring (back of leg)
X. Gastrocnemius (back of calf)
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
M10 x 81mm Bolt (41)
M10 Nylon Locknut (43)
M10 x 75mm Bolt (42)
M8 Nylon Locknut (55)
M10 x 68mm Bolt (54)
M6 Nylon Locknut (51)
M10 x 65mm Bolt (40)
M10 x 60mm Bolt (47)
M10 Washer (44)
M8 x 58mm Bolt (52)
M8 Washer (56)
M6 x 40mm Bolt (49)
M6 Washer (48)
M10 x 19mm Bolt (53)
M4 x 16mm Screw (45)
M6 x 16mm Screw (39)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. 831.15609.0
R0805A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
4
3
6
2
2
2
2
1
3
2
1
4
2
2
Bench Frame
Front Leg
Leg Lever
Crossbar
Right Upright
Left Upright
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
#
1
4
1
1
2
1
1
6
2
2
8
16
4
5
6
1
8
8
1
4
1
1
1
1
2
2
1
1
1
1
10mm Spacer
25mm Round Inner Cap
Curl Knob
Lat Cable
Spring Clip
Cable Clip
Pulley
Weight Rest
Lat Tower
M6 x 16mm Screw
M10 x 65mm Bolt
M10 x 81mm Bolt
M10 x 75mm Bolt
M10 Nylon Locknut
M10 Washer
M4 x 16mm Screw
19mm Round Inner Cap
M10 x 60mm Bolt
M6 Washer
M6 x 40mm Bolt
M10 x 168mm Bolt
M6 Nylon Locknut
M8 x 58mm Bolt
M10 x 19mm Bolt
M10 x 68mm Bolt
M8 Nylon Locknut
M8 Washer
9
Weight Carriage
Backrest Bracket
Curl Post
Backrest Frame
Backrest
Seat
Curl Pad
Weight Tube
Lat Bar
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Joint Plate
Pad Tube
Foam Pad
Weight Rest Cap
Square Bushing
Weight Rest Knob
Lat Tower Bushing
Adjustment Pin
45mm Square Inner Cap
25mm x 51mm Inner Cap
25mm Round Angled Cap
25mm Square Inner Cap
Lat Handgrip
10mm Large Spacer
45mm Thick Square Inner Cap
25mm Thin Round Inner Cap
User’s Manual
Exercise Guide
Grease Pack
#
#
Note: “#” Indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts. If a part is missing, call toll-free 1-877-992-5999.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. 831.15609.0
R0805A
13
30
17
29
7
12
49
57
31
30
47
45
43
44
48
48
48
43
48
45
35
38
48
21
22
31
29
44
49
48
7
50
23
49
51
33
45
51
5
37
45
10
8
43
4
21
22
36
18
23
43
18
42
35
43
24
53
33
33
6
33
14
18
42
9
43
15
41
45
24
40
41
25
57
34
1
43
20
26
46
40
3
39
19
43
26
54
11
39
46
44
27
28
2
32
39
19
55
46
56
58
27
56
16
52
46
26
20
Download from Www.Somanuals.com. All Manuals Search And Download.
FULL 90-DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
WEIGHT BENCH EXERCISER, contact the nearest Sears Service Center throughout the United States
and Sears will repair or replace the WEIGHT BENCH EXERCISER, free of charge.
This warranty does not apply when the WEIGHT BENCH EXERCISER is used commercially or for
rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Sears, Roebuck and Co., Dept 817WA, Hoffman Estates, IL 60179
Part No. 231099 R0805A
Printed in China © 2005 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|