R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
XT 200/XT 25
FeatherLitet Series
Wild Thingt WT21
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le faire
pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2002 Electrolux Home Products, Inc.
530163346
12/5/02
Download from Www.Somanuals.com. All Manuals Search And Download.
CUTTING SAFETY
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti--vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
S Use only for trimming, scalping, mowing and
sweeping. Do not use for edging, pruning or
hedge trimming.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from muffler
and spinning line. Keep engine below waist
level. A hot muffler can cause serious burns.
S Cut from your right to your left. Cutting on left
side of the shield will throw debris away from
the operator.
S Use only in daylight or good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Allow engine to cool; secure unit before stor-
ing or transporting in vehicle.
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. If you
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the carbure-
tor by starting the engine and letting it run until
it stops.
S Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from wa-
ter heaters, electric motors or switches, fur-
naces, etc.
S Store unit so line limiter blade cannot acciden-
tally cause injury. The unit can be hung by the 50 hours of use, we recommend that your
tube.
muffler be serviced or replaced by your autho-
rized service dealer.
S Store unit out of reach of children.
ASSEMBLY
tor and others and is equipped with a line limiter
blade which cuts excess line to the proper
length. The line limiter blade (on underside of
shield) is sharp and can cut you.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
For proper orientation of shield, see KNOW
YOUR TRIMMER illustration in OPERATION
section. Assemble your shield (Style A or B) as
shown.
Examine parts for damage. Do not use dam-
aged parts.
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
STYLE A
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
1. Remove wing nut from shield.
2. Insert bracket into slot as shown.
3. Pivot shield until bolt passes through hole in
bracket.
4. Securely tighten wing nut onto bolt.
ADJUSTING THE HANDLE
Slot
WARNING: When adjusting the han-
dle, be sure it remains between the trigger
and the safety label.
Shield
Bracket
1. Loosen wing nut on handle.
2. Rotate the handle on the tube to an upright
position; retighten wing nut.
ATTACHING SHIELD
Wing
Nut
WARNING: The shield must be prop-
erly installed. The shield provides partial protec-
tion from the risk of thrown objects to the opera-
Line Limiter Blade
3
Download from Www.Somanuals.com. All Manuals Search And Download.
STYLE B
Shield
1. Remove washer and wing nut from shield.
2. Assemble parts as shown in illustration.
3. Securely tighten wing nut onto bolt.
NOTE: Remove
and use washer and
wing nut from this
bolt for assembling
shield.
Line Limiter
Blade
Wing Nut
Washer
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
STYLE A
STYLE B
Assist Handle
Shield
Assist Handle
Tube
Tube
Trimmer Head
Throttle
Trigger
Throttle Trigger
Shield
Trimmer Head
Line Limiter Blade
Line Limiter Blade
Spark Plug
ON/STOP
Switch
Starter Rope
Handle
Choke Lever
Primer Bulb
Fuel Mix Fill Cap
ON/STOP SWITCH
CHOKE
The ON/STOP switch is used to stop engine. To
stop the engine, push and release the engine
ON/STOP switch.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE STARTING ENGINE
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
WARNING: Be sure to read the fuel
information in the safety rules before you
begin. If you do not understand the safety
rules, do not attempt to fuel your unit. Call
1-800-554-6723.
Starting Position
FUELING ENGINE
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle
air-cooled engine oil designed to be mixed at a
ratio of 40:1. Poulan/Weed Eater brand
synthetic oil is recommended. Mix gasoline and
oil at a ratio of 40:1. A 40:1 ratio is obtained by
mixing 3.2 ounces (95 ml) of oil with 1 gallon (4
liters) of unleaded gasoline. DO NOT USE
automotive oil or boat oil. These oils will cause
engine damage. When mixing fuel, follow
instructions printed on container. Once oil is
added to gasoline, shake container momentarily
to assure that the fuel is thoroughly mixed.
Always read and follow the safety rules relating
to fuel before fueling your unit.
1. Set unit on a flat surface.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE
position.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
Starter Handle
Choke
Lever
Muffler
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage.
To avoid engine problems, empty the fuel sys-
tem before storage for 30 days or longer.
Drain the gas tank, start the engine and let it
run until the fuel lines and carburetor are
empty. Use fresh fuel next season.
Primer Bulb
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not
pull rope more than 6 times.
6. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls.
Never use engine or carburetor cleaner prod-
ucts in the fuel tank or permanent damage may
occur. See the STORAGE section for addi-
tional information.
NOTE: If the engine doesn’t start after 6
pulls (at the HALF CHOKE position),
move the choke lever to the FULL
CHOKE position and press the primer
bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the start-
er rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t
start, it is probably flooded. Proceed to
STARTING A FLOODED ENGINE.
8. Once the engine starts, allow it to run 10
seconds, then move the choke lever to
the OFF CHOKE position. Allow the unit
to run for 30 more seconds at OFF
CHOKE before releasing the throttle trig-
ger.
HOW TO STOP YOUR UNIT
S To stop the engine, push and release the
engine ON/STOP switch. The switch will
automatically return to the ON position.
Wait 5 seconds before attempting to restart
unit to allow switch to reset.
S If engine does not stop, move choke to the
FULL CHOKE position.
Engine
Choke Lever
ON/STOP
Switch
NOTE: If engine dies with the choke le-
ver in the OFF CHOKE position, move
the choke lever to the HALF CHOKE
position and pull the rope until engine
runs, but no more than 6 pulls.
HALF
FULL
OFF
HOW TO START YOUR UNIT
WARNING: The trimmer head will
STARTING A WARM ENGINE
1. Move the choke lever to the HALF CHOKE
position.
turn while starting the engine. Avoid any con- 2. Squeeze and hold the throttle trigger. Keep
tact with the muffler. A hot muffler can cause
serious burns.
throttle trigger fully squeezed until the en-
gine runs smoothly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
4. Allow engine to run 15 seconds, then move
the choke lever to OFF CHOKE.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2
in. (5 cm) each time the bottom of the trimmer
head is tapped on the ground with the engine
running at full throttle.
The most efficient line length is the maximum
length allowed by the line limiter.Always keep
the shield in place when the tool is being oper-
ated.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
To advance line:
S Operate the engine at full throttle.
S Hold the trimmer head parallel to and above
the grassy area.
S Tap the bottom of the trimmer head lightly
on the ground one time. Approximately 2 in.
(5 cm) of line will be advanced with each
tap.
Always tap the trimmer head on a grassy
area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the
trimmer head.
OPERATING INSTRUCTIONS
OPERATING POSITION
STYLE A
ALWAYS WEAR:
Eye Protection
If the line is worn down to 2 inches (5 cm) or
less, more than one tap will be required to ob-
tain the most efficient line length.
WARNING: Use only 0.065” (1.65
mm) diameter line. Other sizes and shapes of
line will not advance properly and will result in
improper cutting head function or can cause
serious injury. Do not use other materials
such as wire, string, rope, etc. Wire can break
off during cutting and become a dangerous
missile that can cause serious injury.
Long Pants
Heavy Shoes
CUTTING METHODS
STYLE B
ALWAYS WEAR:
WARNING: Use minimum speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, etc.),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
Eye Protection
S The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Long Pants
Heavy Shoes
Tip of the Line
Line Crowded Into
Does The Cutting Work Area
Cut from your right to your left.
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Wrong
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to “weld” onto the spool.
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
S The line will easily remove grass and
weeds from around walls, fences, trees and
flower beds, but it also can cut the tender
bark of trees or shrubs and scar fences. To
help avoid damage especially to delicate
vegetation or trees with tender bark,
shorten line to 4--5 in. (10--13 cm) and use
at less than full throttle.
S For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
S Release the throttle trigger.
S Push and release the engine ON/STOP
switch.
S During light duty cutting.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
S Near objects around which the line can
wrap such as small posts, trees or fence
wire.
MOWING -- Your trimmer is ideal for mowing
in places conventional lawn mowers cannot
reach. In the mowing position, keep the line
S For mowing or sweeping, use full throttle for parallel to the ground. Avoid pressing the
a good clean job.
head into the ground as this can scalp the
ground and damage the tool.
TRIMMING -- Hold the bottom of the trimmer
head about 3 in. (8 cm) above the ground and
at an angle. Allow only the tip of the line to
make contact. Do not force trimmer line into
work area.
Mowing
Trimming
SWEEPING -- The fanning action of the rotat-
ing line can be used for a quick and easy
clean up. Keep the line parallel to and above
the surfaces being swept and move the tool
from side to side.
3 in. (8 cm)
Above Ground
SCALPING -- The scalping technique re-
moves unwanted vegetationdown to the
ground. Hold the bottom of the trimmer head
about 3 in. (8 cm) above the ground and at an
angle. Allow the tip of the line to strike the
ground around trees, posts, monuments, etc.
This technique increases line wear.
Swee
Scalping
MAINTENANCE
INSPECT AND CLEAN UNIT AND
LABELS
WARNING: Disconnect the spark
plug before performing maintenance except
for carburetor adjustments.
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Assist Handle Screws
S Debris Shield
S Wipe off unit with a clean dry cloth.
CLEAN AIR FILTER
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean after every
5 hours of operation.
CHECK FOR DAMAGED OR
WORN PARTS
1. Clean the cover and the area around it to
keep dirt from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE: To avoid creating a fire hazard or
producing harmful evaporative emissions, do
not clean filter in gasoline or other flammable
solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/STOP Switch -- Ensure ON/STOP
switch functions properly by pushing and
releasing the switch. Make sure engine
stops. Wait 5 seconds before attempting to
restart unit to allow switch to reset. Restart
engine and continue.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
5. Add a few drops of oil to the filter; squeeze
the filter to distribute oil.
6. Replace parts.
er
Screws
Air Filter Cover
7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove spark plug from cylinder and dis-
card.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed and nonadjustable.
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
4. Reinstall the spark plug boot.
1. Twist, then pull off spark plug boot.
SERVICE AND ADJUSTMENTS
10. Pull the line extending outside of the hub to
release it from the notch.
LINE REPLACEMENT
1. Remove spool by firmly pulling on tap but-
ton.
CARBURETOR ADJUSTMENT
2. Clean entire surface of hub and spool.
3. Replace with pre--wound spool, or cut a
length of 18 feet of 0.065! (1.65 mm) diam-
eter Weed Eaterr brand line.
WARNING: Keep others away when
making idle speed adjustments. The trimmer
head will be spinning during this procedure.
Wear your protective equipment and observe
all safety precautions.
The carburetor has been carefully set at the
factory. Adjustments may be necessary if you
notice any of the following conditions:
S Engine will not idle when the throttle is re-
leased.
WARNING: Never use wire, rope,
string, etc., which can break off and become a
dangerous missile.
4. Insert one end of the line about 1/2 inch (1
cm) into the small hole on the inside of
spool.
Make adjustments with the unit supported so
the cutting attachment is off the ground and
will not make contact with any object. Hold
the unit by hand while running and making ad-
justments. Keep all parts of your body away
from the cutting attachment and muffler.
Small
Hole
Spool
Idle Speed Adjustment
Allow engine to idle. Adjust speed until engine
runs without stalling (idle speed too slow).
S Turn idle speed screw clockwise to in-
crease engine speed if engine stalls or dies.
S Turn idle speed screw counterclockwise to
decrease engine speed.
Line in Notch
Line exit hole
5. Wind the line evenly and tightly onto the
spool. Wind in the direction of the arrow
found on the spool.
Idle Speed
Screw
Air Filter
Cover
6. Push the line into the notches, leaving 3 to 5
inches (7 -- 12 cm) unwound.
7. Insert the lines into the exit holes in the hub If you require further assistance or are unsure
as shown in the illustration.
about performing this procedure, contact an
authorized service dealer or call
8. Align the notch with the line exit hole.
9. Push spool into hub until it snaps into place. 1--800--554--6723.
STORAGE
SEASONAL STORAGE
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Lightly oil external metal surfaces.
FUEL SYSTEM
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
S Store unit and fuel well out of the reach of
children.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuel stabilizer is an acceptable alternative in S Replace spark plug with new one of recom-
minimizing the formation of fuel gum deposits
mended type and heat range.
during storage. Add stabilizer to the gasoline S Clean air filter.
in the fuel tank or fuel storage container. Fol- S Check entire unit for loose screws, nuts,
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
5. Carburetor requires
adjustment.
5. Contact an authorized service dealer.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
and regap.
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. Contact an authorized service dealer.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
2. Fuel mixture incorrect.
1. Adjust choke.
2. Empty fuel tank and refill with
correct fuel mixture.
smokes
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
4. Contact an authorized service dealer.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
not cover predelivery setup or normal
warrants to the original purchaser that each new adjustments explained in the instruction manual.
Weed Eaterr brand gasoline tool or attachment
is free from defects in material and
workmanship and agrees to repair or replace
under this warranty any defective gasoline
product or attachment as follows from the
original date of purchase.
1 YEAR -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS -- Parts and Labor, if used for rental WARRANTY LASTS OR THE EXCLUSION
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES
EXCEPT
THOSE
EXPRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED
OR LIMITATIONS OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATIONS OR EXCLUSION
MAY NOT APPLY TO YOU.
accessories and/or attachments not specifically The policy of ELECTROLUX HOME
recommended by ELECTROLUX HOME PRODUCTS, INC., is to continuously
PRODUCTS, INC., for this tool. Additionally, improve its products. Therefore,
this warranty does not cover tune--ups, spark ELECTROLUX HOME PRODUCTS, INC.,
plugs, filters, starter ropes, starter springs, reserves the right to change, modify, or
cutting line, or rotating head parts that will wear discontinue models, designs, specifications,
and require replacement with reasonable use and accessories of all products at any time
during the warranty period. This warranty does without notice or obligation to any purchaser.
U.S. EPA/ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance.
TIONS: The U. S. Environmental Protection
Agency, Environment Canada and ELEC- As the small off--road engine owner, you should
TROLUX HOME PRODUCTS, INC., are
be aware that ELECTROLUX HOME PROD-
pleased to explain the emissions control system UCTS, INC., may deny you warranty coverage
warranty on your year 2002--2004 small off-- if your small off--road engine or a part of it has
road engine. ELECTROLUX HOME PROD-
failed due to abuse, neglect, improper mainte-
UCTS, INC., must warrant the emission control nance, unapproved modifications, or the use of
system on your small off--road engine for the pe- parts not made or approved by the original
riods of time listed below provided there has equipment manufacturer. You are responsible
been no abuse, neglect, or improper mainte- for presenting your small off--road engine to an
nance of your small off--road engine. Your emis- ELECTROLUX HOME PRODUCTS, INC., au-
sion control system includes parts such as the thorized repair center as soon as a problem ex-
carburetor and the ignition system. Where a ists. Warranty repairs should be completed in a
warrantable condition exists, ELECTROLUX reasonable amount of time, not to exceed 30
HOME PRODUCTS, INC., will repair your small
days. If you have any questions regarding your
off--road engine at no cost to you. Expenses warranty rights and responsibilities, you should
covered under warranty include diagnosis, contact your nearest authorized service center
parts and labor. MANUFACTURER’S WAR-
RANTY COVERAGE: If any emissions related
or call ELECTROLUX HOME PRODUCTS,
INC., at 1--800--554--6723. WARRANTY
part on your engine (as listed under Emissions COMMENCEMENT DATE: The warranty peri-
Control Warranty Parts List) is defective or a de- od begins on the date the small off--road engine
fect in the materials or workmanship of the en- is purchased. LENGTH OF COVERAGE: This
gine causes the failure of such an emission re- warranty shall be for a period of two years from
lated part, the part will be repaired or replaced the initial date of purchase. WHAT IS COV-
by ELECTROLUX HOME PRODUCTS, INC.
OWNER’S WARRANTY RESPONSIBILI-
ERED: REPAIR OR REPLACEMENT OF
PARTS. Repair or replacement of any war-
TIES: As the small off--road engine owner, you ranted part will be performed at no charge to the
are responsible for the performance of the re- owner at an approved ELECTROLUX HOME
quired maintenance listed in your instruction PRODUCTS, INC., servicing center. If you
manual. ELECTROLUX HOME PRODUCTS,
have any questions regarding your warranty
INC., recommends that you retain all receipts rights and responsibilities, you should contact
covering maintenance on your small off--road your nearest authorized service center or call
engine, but ELECTROLUX HOME PROD-
UCTS, INC., cannot deny warranty solely for
ELECTROLUX HOME PRODUCTS, INC., at
1--800--554--6723. WARRANTY PERIOD: Any
10
Download from Www.Somanuals.com. All Manuals Search And Download.
warranted part which is not scheduled for re- use of add--on or modified parts. HOW TO FILE
placement as required maintenance, or which is A CLAIM: If you have any questions regarding
scheduled only for regular inspection to the ef- your warranty rights and responsibilities, you
fect of “repair or replace as necessary” shall be should contact your nearest authorized service
warranted for 2 years. Any warranted part which center or call ELECTROLUX HOME PROD-
is scheduled for replacement as required main- UCTS, INC., at 1--800--554--6723. WHERE TO
tenance shall be warranted for the period of time GET WARRANTY SERVICE: Warranty ser-
up to the first scheduled replacement point for vices or repairs shall be provided at all ELEC-
that part. DIAGNOSIS: The owner shall not be TROLUX HOME PRODUCTS, INC., service
charged for diagnostic labor which leads to the centers. Call 1--800--554--6723. MAINTE-
determination that a warranted part is defective NANCE, REPLACEMENT AND REPAIR OF
if the diagnostic work is performed at an ap- EMISSION RELATED PARTS: Any ELEC-
proved ELECTROLUX HOME PRODUCTS,
INC., servicing center. CONSEQUENTIAL
DAMAGES: ELECTROLUX HOME PROD-
TROLUX HOME PRODUCTS, INC., approved
replacement part used in the performance of
any warranty maintenance or repair on emis-
UCTS, INC., may be liable for damages to other sion related parts will be provided without
engine components caused by the failure of a charge to the owner if the part is under warranty.
warranted part still under warranty. WHAT IS EMISSION CONTROL WARRANTY PARTS
NOT COVERED: All failures caused by abuse,
neglect, or improper maintenance are not cov- (covered up to maintenance schedule), Ignition
ered. ADD--ON OR MODIFIED PARTS: The Module. MAINTENANCE STATEMENT: The
LIST: Carburetor, Ignition System: Spark Plug
use of add--on or modified parts can be grounds owner is responsible for the performance of all
for disallowing a warranty claim. ELECTRO- required maintenance as defined in the in-
LUX HOME PRODUCTS, INC., is not liable to
cover failures of warranted parts caused by the
struction manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
|