| 	
		 R 
					Trademark   
					Please do not return unit to retailer.   
					Por favor, no devuelva el aparato al lugar de compra.   
					Veuillez ne pas retourner l’outil au détaillant.   
					1-800-554-6723   
					
					Operator’s Manual   
					Manual del Operador   
					Manuel de L’utilisateur   
					PL 500   
					U 
					RL   
					For Occasional Use Only   
					WARNING:   
					Read and follow all Safety Rules and Operating Instructions before   
					using this product. Failure to do so can result in serious injury.   
					ADVERTENCIA:   
					Lea el manual del operador y siga todas las advertencias e instruc-   
					ciones de seguridad. El no hacerlo puede resultar en lesiones graves.   
					AVERTISSEMENT:   
					Lire le manuel de l’utilisateur et bien respecter tous les avertisse-   
					ments et toutes les instructions de sécurité. Tout défaut de le faire   
					pourrait entraîner des blessures graves.   
					Electrolux Home Products   
					North America   
					Div. of WCI Outdoor Products, Inc.   
					Augusta, GA 30907   
					Copyright E2000 WCI Outdoor Products, Inc.   
					530088828 10/30/00   
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				S Stop engine and allow to cool before re- ments of California Codes 4442 and 4443. All   
					moving fuel cap.   
					U.S. forest land and the states of California,   
					Idaho, Maine, Minnesota, New Jersey, Ore-   
					gon, and Washington require by law that   
					many internal combustion engines be   
					equipped with a spark arresting screen. If you   
					operate in a locale where such regulations ex-   
					ist, you are legally responsible for maintaining   
					the operating condition of these parts. Failure   
					to do so is a violation of the law. For normal   
					homeowner use, the muffler and spark arrest-   
					ing screen will not require any service. After   
					50 hours of use, we recommend that your   
					muffler be serviced or replaced by your Au-   
					thorized Service Dealer.   
					S Always store gasoline in a container ap-   
					proved for flammable liquids.   
					CUTTING SAFETY   
					WARNING: Inspect the area before   
					each use. Remove objects (rocks, broken   
					glass, nails, wire, etc.) which can be thrown   
					by or become entangled in line. Hard objects   
					can damage the trimmer head and be thrown   
					causing serious injury.   
					S Use only for trimming, mowing, and sweep-   
					ing. Do not use for edging, pruning, or   
					hedge trimming.   
					S Keep firm footing and balance. Do not over-   
					reach.   
					ASSEMBLY   
					S Keep all parts of your body away from muf-   
					fler and spinning line. Keep engine below   
					waist level. A hot muffler can cause serious   
					burns.   
					WARNING: Make sure unit is proper-   
					ly assembled and all fasteners are secure.   
					S Cutting on left side of the shield will throw   
					debris away from the operator.   
					ADJUST THE HANDLE   
					S Loosen wing nut or plastic knob on handle.   
					S Rotate handle to upright position and tight-   
					en in a comfortable position between the   
					trigger and the safety label on the tube.   
					Tighten handle securely.   
					S Use only in daylight or good artificial light.   
					TRANSPORTING AND STORAGE   
					S Allow the engine to cool; secure unit before   
					storing or transporting in vehicle.   
					S Empty fuel tank before storing or transport-   
					ing the unit. Use up fuel left in the carburetor   
					by starting engine and letting it run until it   
					stops.   
					ATTACH THE SHIELD   
					WARNING: The shield must be prop-   
					erly installed. The shield provides partial   
					protection from the risk of thrown objects to   
					the operator and others and is equipped with   
					a line limiter blade which cuts excess line. The   
					line limiter blade (on underside of shield) is   
					sharp and can cut you.   
					S Store unit and fuel in an area where fuel va-   
					pors cannot reach sparks or open flames   
					from water heaters, electric motors or   
					switches, furnaces, etc.   
					S Store unit so line limiter blade cannot acci-   
					dentally cause injury. Unit can be hung by   
					the tube.   
					S Insert bracket into slot on shield.   
					S Pivot shield until bolt passes through hole in   
					bracket.   
					S Store the unit out of the reach of children   
					If situations occur which are not covered in   
					this manual, use care and good judgment. If   
					you need assistance, call 1-800-554-6723.   
					S Securely tighten wing nut.   
					S Remove packing cover from the arbor shaft   
					if so equipped. Thread trimmer head onto   
					shaft; tighten securely against dust cup.   
					SAFETY NOTICE: Exposure to vibrations   
					through prolonged use of gasoline powered   
					hand tools could cause blood vessel or nerve   
					damage in the fingers, hands, and joints of   
					people prone to circulation disorders or ab-   
					normal swellings. Prolonged use in cold   
					weather has been linked to blood vessel dam-   
					age in otherwise healthy people. If symptoms   
					occur such as numbness, pain, loss of   
					strength, change in skin color or texture, or   
					loss of feeling in the fingers, hands, or joints,   
					discontinue the use of this tool and seek med-   
					ical attention. An anti--vibration system does   
					not guarantee the avoidance of these prob-   
					lems. Users who operate power tools on a   
					continual and regular basis must monitor   
					closely their physical condition and the condi-   
					tion of this tool.   
					Wing Nut   
					Bracket   
					Slot   
					Dust Cup   
					Shield   
					SPECIAL NOTICE: This unit is equipped   
					with a temperature limiting muffler and spark   
					arresting screen which meets the require-   
					3 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				S Pull starter rope handle until engine runs.   
					S If engine does not start in 5 pulls, follow   
					instructions in STARTING A COLD ENGINE.   
					FUEL YOUR UNIT   
					This engine is certified to operate on un-   
					leaded gasoline. Gasoline must be mixed   
					with a good quality 2-cycle air-cooled engine   
					oil designed to be mixed at a ratio of 40:1.   
					Poulan/Weed Eater brand oil is recom-   
					mended. (A 40:1 ratio is obtained by mixing   
					3.2 ounces of oil with 1 gallon of unleaded   
					gasoline). When mixing fuel follow the   
					instructions printed on the container. Always   
					read and follow the safety rules under FUEL   
					SAFETY.   
					USING YOUR UNIT   
					OPERATING POSITION   
					ALWAYS WEAR:   
					Eye Protection   
					Long Pants   
					Heavy Shoes   
					STARTING   
					Cut from your right to your left.   
					To stop the engine, push and release the en- ADVANCING THE CUTTING LINE   
					HOW TO STOP YOUR UNIT   
					gine STOP switch. The switch will automati-   
					cally return to the ON position. Wait 5 sec-   
					onds before attempting to restart unit to allow   
					switch to reset.   
					Advance line by tapping the bottom of the cut-   
					ting head lightly on the ground while engine is   
					running at full speed. The metal line limiter   
					blade attached to the shield will cut the line to   
					the proper length.   
					HOW TO START YOUR UNIT   
					REPLACING THE LINE   
					S Remove spool by firmly pulling on tap but-   
					ton.   
					Starting Positio 
					S Clean entire surface of hub and spool.   
					S Replace with a pre-wound spool, or cut two   
					lengths of 12-1/2 feet of .080” (2 mm) diam-   
					eter Weed Eaterr brand line. Never use   
					wire, rope, string, etc., which can break off   
					and become a dangerous missile.   
					S Insert ends of the line about 1/2 inch (1 cm)   
					into the small hole on the inside of spool.   
					Choke lever   
					Trigger   
					Spool   
					Small   
					Holes   
					Primer Bulb   
					Muffler   
					WARNING: The trimmer head will   
					turn while starting the engine. Avoid any con-   
					tact with the muffler. A hot muffler can cause   
					serious burns.   
					Line exit holes   
					Line in Notch   
					STARTING A COLD ENGINE (or a   
					warm engine after running out of   
					fuel)   
					S Set unit on a flat surface.   
					S Slowly press the primer bulb 6 times.   
					S Move choke lever to FULL CHOKE posi-   
					tion.   
					Line in Notch   
					Hub   
					S Squeeze the throttle trigger fully and hold   
					through all remaining steps.   
					S Wind the line evenly and tightly onto the   
					spool. Wind in the direction of the arrows   
					found on the spool.   
					S Pull starter rope handle sharply 6 times.   
					S Move choke lever to HALF CHOKE posi-   
					tion.   
					S Push the lines into the notches, leaving 3 to   
					5 inches (7 -- 12 cm) unwound.   
					S Pull starter rope handle no more than 6   
					pulls, until engine runs.   
					S Insert the lines into the the exit holes in the   
					hub as shown in the illustration.   
					S Allow engine to run 10 seconds, then move   
					choke lever to OFF CHOKE position.   
					S Align the notches with the line exit holes.   
					S Push spool into hub until it snaps into place.   
					S Pull the lines extending outside of the hub to   
					release them from the notches.   
					STARTING A WARM ENGINE   
					S Move choke lever to OFF CHOKE position.   
					4 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				We recommend that you take your unit to an   
					Authorized Service Dealer. Damage will oc-   
					cur if you turn the needles beyond the limiter   
					stops.   
					SERVICE   
					We recommend all service and adjustments   
					not listed in this manual be performed by an   
					Authorized Service Dealer.   
					IGNITION TIMING   
					The ignition timing is fixed, non-adjustable.   
					CARBURETOR ADJUSTMENTS   
					SPARK PLUG   
					Your carburetor is equipped with limiter caps. Replace the spark plug yearly using a Cham-   
					Carburetor adjustment is a complicated task. pion RCJ--8Y plug. Spark plug gap is 0.025”.   
					TROUBLESHOOTING TABLE   
					WARNING: Always stop unit and disconnect spark plug before performing any of the   
					recommended remedies below other than remedies that require operation of the unit.   
					TROUBLE   
					CAUSE   
					REMEDY   
					S See “Starting.”   
					Engine will not S Engine flooded.   
					S Fill tank with correct fuel mixture.   
					S Install new spark plug.   
					S Fuel tank empty.   
					S Spark plug not firing.   
					S Fuel not reaching carburetor.   
					start.   
					S Check for dirty fuel filter; replace.   
					Check for kinked or split fuel line;   
					repair or replace.   
					S See “Carburetor Adjustments.”   
					S Carburetor requires adjustment.   
					Engine will not S Carburetor requires adjustment. S See “Carburetor Adjustments.”   
					S Throttle trigger screw too   
					tight.   
					S Loosen screw.   
					idle properly.   
					Engine will not S Air filter dirty.   
					S Clean or replace air filter.   
					S Spark plug fouled.   
					S Clean or replace spark plug; re-gap.   
					accelerate,   
					lacks power,   
					or dies under   
					a load.   
					S Carburetor requires adjustment. S See “Carburetor Adjustments.”   
					Engine   
					S Fuel mixture incorrect.   
					S Air filter dirty.   
					S Empty fuel tank and refill with   
					correct fuel mixture.   
					smokes   
					S Clean or replace air filter.   
					excessively.   
					S Carburetor requires adjustment. S See “Carburetor Adjustments.”   
					Line does not   
					advance or   
					breaks while   
					cutting.   
					S Check line routing.   
					S Line improperly routed in head.   
					S Line improperly wound on   
					spool.   
					S Rewind line tightly and evenly.   
					S Use only 0.080” (2 mm) dia. line.   
					S Line size incorrect.   
					S Use only 0.080” (2 mm) dia. line.   
					S Replace with correct spool.   
					S Cut with tip of line fully extended.   
					Line welds   
					onto spool.   
					S Line size incorrect.   
					S Incorrect spool.   
					S Line is being crowded against   
					material being cut.   
					S Remove spool and pull 4 inches   
					(10 cm) of line outside of head.   
					S Use only 0.080” (2 mm) dia. line.   
					Line pulls   
					back into   
					head.   
					S Too little line outside of head.   
					S Line size incorrect.   
					5 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				U.S. EPA   
					EMISSION CONTROL   
					WARRANTY STATEMENT   
					NEED ASSISTANCE?   
					Need Assistance?   
					Call 1-800-554-6723.   
					Need Service Parts?   
					YOUR WARRANTY RIGHTS AND OB-   
					LIGATIONS: The U. S. Environmental   
					Protection Agency and POULAN/WEED   
					EATER, DIVISION OF WCI OUTDOOR   
					PRODUCTS are pleased to explain the emis-   
					sions control system warranty on your lawn   
					and garden equipment engine. All new utility   
					and lawn and garden equipment engines   
					must be designed, built, and equipped to meet   
					the stringent anti--smog standards. POU-   
					LAN/WEED EATER must warrant the emis-   
					sion control system on your lawn and garden   
					equipment engine for the periods of time listed   
					below provided there has been no abuse, ne-   
					glect, or improper maintenance of your lawn   
					and garden equipment engine. Your emission   
					control system includes parts such as the   
					carburetor and the ignition system. Where a   
					warrantable condition exits, POULAN/WEED   
					EATER will repair your lawn and garden   
					equipment engine at no cost to you. Ex-   
					penses covered under warranty include diag-   
					nosis, parts and labor. MANUFACTURER’S   
					WARRANTY COVERAGE: If any emissions   
					related part on your engine (as listed under   
					Emissions Control Warranty Parts List) is de-   
					fective or a defect in the materials or work-   
					manship of the engine causes the failure of   
					such an emission related part, the part will be   
					repaired or replaced by POULAN/WEED   
					EATER. OWNER’S WARRANTY RESPON-   
					SIBILITIES: As the lawn and garden equip-   
					ment engine owner, you are responsible for   
					the performance of the required maintenance   
					listed in your Owner’s Manual. POULAN/   
					WEED EATER recommends that you retain   
					all receipts covering maintenance on your   
					lawn and garden equipment engine, but POU-   
					LAN/WEED EATER cannot deny warranty   
					solely for the lack of receipts or for your failure   
					to ensure the performance of all scheduled   
					maintenance. As the lawn and garden equip-   
					ment engine owner, you should be aware that   
					POULAN/WEED EATER may deny you war-   
					ranty coverage if your lawn and garden equip-   
					ment engine or a part of it has failed due to   
					abuse, neglect, improper maintenance, un-   
					approved modifications, or the use of parts   
					not made or approved by the original equip-   
					ment manufacturer. You are responsible for   
					presenting your lawn and garden equipment   
					engine to a POULAN/WEED EATER autho-   
					rized repair center as soon as a problem ex-   
					ists. Warranty repairs should be completed in   
					a reasonable amount of time, not to exceed   
					Contact your dealer or place of purchase.   
					LIMITED WARRANTY   
					ELECTROLUX   
					HOME   
					PRODUCTS   
					NORTH AMERICA, Division of WCI Out-   
					door Products, Inc., warrants to the original   
					purchaser that each new Weed Eater brand   
					gasoline tool or attachment is free from de-   
					fects in material and workmanship and   
					agrees to repair or replace under this war-   
					ranty any defective gasoline product or at-   
					tachment as follows from the original date of   
					purchase.   
					2 YEARS-- Parts and Labor, when used for   
					household purposes.   
					90 DAYS -- Parts and Labor, when used for   
					commercial, professional, or income produc-   
					ing purposes.   
					30 DAYS -- Parts and Labor, if used for rental   
					purposes.   
					This warranty is not transferable and does not   
					cover damage or liability caused by improper   
					handling, improper maintenance, or the use   
					of accessories and/or attachments not spe-   
					cifically recommended by ELECTROLUX   
					HOME PRODUCTS NORTH AMERICA for   
					this tool. Additionally, this warranty does not   
					cover tune-ups, spark plugs, filters, cutting   
					line, or rotating head parts that will wear and   
					require replacement with reasonable use dur-   
					ing the warranty period. This warranty does   
					not cover predelivery setup or normal adjust-   
					ments explained in the operator’s manual.   
					THIS WARRANTY GIVES YOU SPECIFIC   
					LEGAL RIGHTS, AND YOU MAY HAVE   
					OTHER RIGHTS WHICH VARY FROM   
					STATE TO STATE.   
					NO CLAIMS FOR CONSEQUENTIAL OR   
					OTHER DAMAGES WILL BE ALLOWED,   
					AND THERE ARE NO OTHER EXPRESS   
					WARRANTIES EXCEPT THOSE EX-   
					PRESSLY STIPULATED HEREIN.   
					SOME STATES DO NOT ALLOW LIMITA-   
					TIONS ON HOW LONG AN IMPLIED WAR-   
					RANTY LASTS OR THE EXCLUSION OR   
					LIMITATIONS OF INCIDENTAL OR CON-   
					SEQUENTIAL DAMAGES, SO THE ABOVE   
					LIMITATIONS OR EXCLUSION MAY NOT   
					APPLY TO YOU.   
					ELECTROLUX   
					NORTH AMERICA’S policy is to continu-   
					ously improve its products. Therefore, ELEC- 30 days. If you have any questions regarding   
					TROLUX HOME PRODUCTS reserves the   
					your warranty rights and responsibilities, you   
					right to change, modify, or discontinue mod- should contact your nearest authorized ser-   
					els, designs, specifications, and accessories vice center or call POULAN/WEED EATER at   
					of all products at any time without notice or 1--800--554--6723.   
					WARRANTY COM-   
					obligation to any purchaser.   
					MENCEMENT DATE: The warranty period   
					HOME   
					PRODUCTS   
					6 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				begins on the date the lawn and garden equip- ranted part still under warranty. WHAT IS   
					ment engine is purchased. LENGTH OF   
					COVERAGE: This warranty shall be for a pe-   
					NOT COVERED: All failures caused by   
					abuse, neglect, or improper maintenance are   
					riod of two years from the initial date of pur- not covered. ADD--ON OR MODIFIED   
					chase. WHAT IS COVERED: REPAIR OR   
					REPLACEMENT OF PARTS. Repair or re-   
					PARTS: The use of add--on or modified parts   
					can be grounds for disallowing a warranty claim.   
					placement of any warranted part will be per- POULAN/WEED EATER is not liable to cover   
					formed at no charge to the owner at an ap- failures of warranted parts caused by the use   
					proved POULAN/WEED EATER servicing   
					center. If you have any questions regarding   
					of add--on or modified parts. HOW TO FILE A   
					CLAIM: If you have any questions regarding   
					your warranty rights and responsibilities, you your warranty rights and responsibilities, you   
					should contact your nearest authorized ser- should contact your nearest authorized ser-   
					vice center or call POULAN/WEED EATER at   
					1--800--554--6723 WARRANTY PERIOD:   
					vice center or call POULAN/WEED EATER at   
					1--800--554--6723 . WHERE TO GET WAR-   
					Any warranted part which is not scheduled for RANTY SERVICE: Warranty services or re-   
					replacement as required maintenance, or pairs shall be provided at all POULAN/WEED   
					which is scheduled only for regular inspection   
					to the effect of “repair or replace as neces-   
					sary” shall be warranted for 2 years. Any war-   
					ranted part which is scheduled for replace-   
					EATER service centers. call: 1--800--554--6723   
					MAINTENANCE, REPLACEMENT AND RE-   
					PAIR OF EMISSION RELATED PARTS: Any   
					POULAN/WEED EATER approved replace-   
					ment as required maintenance shall be ment part used in the performance of any war-   
					warranted for the period of time up to the first ranty maintenance or repair on emission re-   
					scheduled replacement point for that part. lated parts will be provided without charge to   
					DIAGNOSIS: The owner shall not be   
					the owner if the part is under warranty. EMIS-   
					charged for diagnostic labor which leads to SION CONTROL WARRANTY PARTS   
					the determination that a warranted part is de- LIST: Carburetor, Ignition System: Spark   
					fective if the diagnostic work is performed at Plug (covered up to maintenance schedule),   
					an approved POULAN/WEED EATER serv-   
					icing center. CONSEQUENTIAL DAM-   
					AGES: POULAN/WEED EATER may be li-   
					able for damages to other engine   
					components caused by the failure of a war-   
					Ignition Module. MAINTENANCE STATE-   
					MENT: The owner is responsible for the per-   
					formance of all required maintenance as de-   
					fined in the owner’s manual.   
					7 
					Download from Www.Somanuals.com. All Manuals Search And Download.   
				 | 
Whirlpool Range 9762354A User Manual
Wibur Curtis Company Ice Tea Maker PTTD 3 User Manual
Xerox Car Video System XM3 22W User Manual
Xerox Printer 12CP User Manual
Xerox Printer 377CF User Manual
Zagg Portable Speaker 780MV50MV User Manual
Zanussi Dishwasher ZSF 6126 User Manual
Zanussi Refrigerator 110719 User Manual
Zephyr Ventilation Hood ZTO M795 User Manual
Zhumell Telephone ECLIPSE 114 User Manual