R
Trademark
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
WT3100
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en le-
siones graves.
AVERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse-
ments et toutes les instructions de sécurité. Tout défaut de le
faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc.
250 Bobby Jones Expressway
Augusta, GA 30907
Copyright E2002 Electrolux Home Products, Inc.
530088156
4/24/02
Download from Www.Somanuals.com. All Manuals Search And Download.
S Move at least 10 feet (3 meters) away from
fueling site before starting engine.
S Stop engine and allow to cool before remov-
ing fuel cap.
S Store unit and fuel in an area where fuel va-
pors cannot reach sparks or open flames
from water heaters, electric motors or
switches, furnaces, etc.
S Always store gasoline in a container ap-
S Store the unit out of the reach of children
proved for flammable liquids.
CUTTING SAFETY
SPECIAL NOTICE: This unit is not
equipped with a temperature limiting muffler
and spark arresting screen which meets the
requirements of California Codes 4442 and
4443. All U.S. forest land and the states of
California, Idaho, Maine, Minnesota, New
WARNING: Inspect the area before
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects Jersey, Oregon, and Washington require by
can damage trimmer head and be thrown
causing serious injury.
law that many internal combustion engines to
be equipped with a spark arrestor screen. If
you operate in a locale where such regula-
tions exist, you are legally responsible for
installing and maintaining the operating con-
dition of these parts. Failure to do so is a viola-
tion of the law. If a spark arrestor is required
in your area, contact your authorized service
dealer for the proper kit.
S Use unit properly. Use only for trimming,
mowing, and sweeping. Do not use for edg-
ing, pruning, or hedge trimming. Do not force
unit. It will do the job better, and with less risk
of injury, at the rate for which it was designed.
S Keep firm footing and balance. Do not over-
reach.
S Keep all parts of your body away from spin-
ning line and muffler. Keep engine and cutting
head below waist level. A hot muffler can
cause serious burns.
S Cut only from your right to your left. Cutting
with the line on right side of the shield will
throw debris away from the operator.
S Use only in daylight or in good artificial light.
S Use only for jobs explained in this manual.
TRANSPORTING AND STORAGE
S Stop the unit when not in use.
S Carry or transport the unit with engine
stopped.
S Allow the engine to cool; secure unit before
storing or transporting in vehicle.
S Empty the fuel tank before storing or trans-
porting the unit. Use up fuel left in the car-
buretor by starting the engine and letting it
run until it stops.
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or ab-
normal swellings. Prolonged use in cold
weather has been linked to blood vessel dam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek med-
ical attention. An anti-vibration system does
not guarantee the avoidance of these prob-
lems. Users who operate power tools on a
continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
ASSEMBLY
4. Align holes and insert curved head tube
bolt through upper and lower handles.
5. Re--install and securely tighten upper wing
nut onto bolt.
WARNING: If received assembled,
repeat all steps to ensure your unit is properly
assembled and all fasteners are secure.
Examine parts for damage. Do not use dam-
aged parts.
6. Retighten lower wing nut securely.
ndle
NOTE: If you need assistance or find parts
missing or damaged, call 1-800-554-6723.
dle
It is normal for the fuel filter to rattle in the
empty fuel tank.
Finding fuel or oil residue on muffler is normal
due to carburetor adjustments and testing
done by the manufacturer.
ATTACH THE HANDLE
1. Remove upper wing nut and curved head
tube bolt from upper handle.
2. Loosen lower wing nut on lower handle.
Tube bolt
Upper wing nut
3. Insert upper handle over lower handle.
NOTE: Ensure upper handle grips are in
position as shown in the following illustrations
(throttle handle grip on left side).
Lower wing nut
3
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Align one cable clamp above the tube bolts
and the other below the starter rope han-
dle. Install the cable clamps one at a time
around the tube and throttle cable.
NOTE: When performing the following step,
be sure the starter rope is not caught under
the cable clamps. The starter rope must
hang freely to operate properly.
NOTE: Ensure throttle cable is in groove of
clamps and lies flat against the upper handle
tube after installation (see illustration above).
Cabl
clam
Starter rope
Throttle
cable
OPERATION
KNOW YOUR TRIMMER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Throttle Trigger
Starter Rope
Handle
ON/OFF
Switch
Upper Handle
Primer Bulb
Muffler
Lower Handle
Trimmer Head
Shield
ON/OFF SWITCH
CHOKE
The ON/OFF switch is used to stop engine. To
stop the engine, move the switch to the OFF
position.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After the engine attempts to start, move
the choke lever to the HALF CHOKE position.
Once engine has started, move the choke lever
to the OFF CHOKE position.
PRIMER BULB
The PRIMER BULB removes air from the car-
buretor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate the primer
bulb by pressing it and allowing it to return to
its original form.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE STARTING ENGINE
STARTING A COLD ENGINE (or a
warm engine after running out of
fuel)
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
1. Move ON/OFF switch to the ON position.
2. Slowly press the primer bulb 6 times.
3. Move choke lever to the FULL CHOKE posi-
tion.
4. Squeeze the throttle trigger fully and hold
through all remaining steps.
FUELING ENGINE
5. Pull starter rope handle sharply until engine
sounds as if it is trying to start, but do not pull
rope more than 6 times.
WARNING: Remove fuel cap slowly
when refueling.
This engine is certified to operate on unleaded
gasoline. Before operation, gasoline must be
mixed with a good quality synthetic 2-cycle air-
cooled engine oil designed to be mixed at a ratio
of 40:1. Poulan/Weed Eater brand synthetic oil
is recommended. Mix gasoline and oil at a ratio
of 40:1. A 40:1 ratio is obtained by mixing 3.2
ounces of oil with 1 gallon of unleaded gasoline.
DO NOT USE automotive oil or boat oil. These
oils will cause engine damage. When mixing
fuel, follow instructions printed on container.
Once oil is added to gasoline, shake container
momentarily to assure that the fuel is thoroughly
mixed. Always read and follow the safety rules
relating to fuel before fueling your unit.
6. As soon as engine sounds as if it is trying to
start, move choke lever to HALF CHOKE
position.
7. Pull starter rope sharply until engine runs,
but no more than 6 pulls. NOTE: If the en-
gine doesn’t start after 6 pulls (at the HALF
CHOKE position), move the choke lever to
the FULL CHOKE position and press the
primer bulb 6 times. Squeeze and hold the
throttle trigger and pull the starter rope 2
more times. Move the choke lever to the
HALF CHOKE position and pull the starter
rope until the engine runs, but no more
than 6 pulls. If the engine still doesn’t start,
it is probably flooded. Proceed to START-
ING A FLOODED ENGINE.
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during stor-
age. Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer. Drain the gas tank,
start the engine and let it run until the fuel lines
and carburetor are empty. Use fresh fuel next
season.Never use engine or carburetor cleaner
products in the fuel tank or permanent damage
may occur. See the STORAGE section for
additional information.
8. Once the engine starts, allow it to run 10
seconds, then move the choke lever to the
OFF CHOKE position. Allow the unit to run
for 30 more seconds at OFF CHOKE be-
fore releasing the throttle trigger.
NOTE: If engine dies with the choke le-
ver in the OFF CHOKE position, move the
choke lever to the HALF CHOKE position
and pull the rope until engine runs, but no
more than 6 pulls.
STARTING A WARM ENGINE
1. Move the ON/OFF switch to the ON posi-
tion.
2. Move the choke lever to the HALF CHOKE
position.
HOW TO STOP YOUR UNIT
S To stop the engine, move the ON/OFF
switch to the OFF position until the unit has
fully stopped.
3. Squeeze and hold the throttle trigger. Keep
throttle trigger fully squeezed until the engine
runs smoothly.
S If engine does not stop, move choke to the
4. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
FULL CHOKE position.
Choke Lever
ON/OFF
Switch
5. Allow engine to run 15 seconds, then move
the choke lever to OFF CHOKE.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run, it
is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing
the choke lever in the OFF CHOKE position;
then, pull the rope to clear the engine of ex-
cess fuel. This could require pulling the starter
handle many times depending on how badly
the unit is flooded.
If the unit still doesn’t start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723.
Primer Bulb
Muffler
HOW TO START YOUR UNIT
WARNING: The trimmer head will
turn while starting the engine. Avoid any con-
tact with the muffler. A hot muffler can cause
serious burns.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
OPERATING POSITION
WARNING: Always wear eye protec-
tion. Never lean over the trimmer head.
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration.
ALWAYS U
Eye
Protection
Heavy L
Pan
Heavy
Shoes
Always release the throttle trigger and allow the
engine to return to idle speed when not cutting.
To stop engine:
Cut from your right to your left.
NOTE: Keep left and right hands on grips
during operation of unit as shown above to
avoid covering air intake holes located on un-
derside of upper handle.
S Release the throttle trigger.
S Move the ON/OFF switch to the OFF posi-
tion.
MAINTENANCE
WARNING: Disconnect the spark
WARNING: Stop your unit before at-
plug before performing maintenance except tempting to clean the intake screen. DO NOT
for carburetor adjustments.
USE GARDEN HOSE OR PRESSURE
WASHER TO CLEAN THIS UNIT!
S Clean the intake screen periodically with a
nylon brush.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Debris Shield
CLEAN THE AIR FILTER
A dirty air filter decreases engine perfor-
mance and increases fuel consumption and
harmful emissions. Always clean with engine
stopped. Clean filter after every 5 hours of op-
eration.
CHECK FOR DAMAGED OR
WORN PARTS
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S ON/OFF Switch -- Ensure ON/OFF switch
functions properly by moving the switch to
the OFF position. Make sure engine stops;
then restart engine and continue.
1. Clean the air filter cover and the area
around the cover to prevent dirt from falling
into the carburetor chamber when the cov-
er is removed.
2. Remove parts as illustrated. It is not nec-
essary to remove the air filter hose from
the air filter cover.
S Fuel Tank -- Discontinue use of unit if fuel
tank shows signs of damage or leaks.
S Debris Shield -- Discontinue use of unit if
debris shield is damaged.
NOTE: If the air filter hose becomes unat-
tached from the cover or lower handle during
cleaning, reattach before attempting to restart
the engine or operate the unit.
INSPECT AND CLEAN UNIT AND
LABELS
Air Filter
Hose
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
labels using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
CLEAN THE AIR INTAKE SCREEN
The air intake screen allows air to circulate to
keep the engine functioning properly and pre-
vents debris from entering the engine.
Air Filter Cover
Screws
NOTE: Do not clean filter in gasoline or oth-
er flammable solvent to avoid creating a fire
hazard or producing harmful evaporative
emissions.
Air inta
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add 10 -- 15 drops of oil to the filter;
squeeze the filter to distribute oil.
NOTE: FILTER MUST BE OILED!
6. Replace parts.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure
the engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed and nonadjustable.
3. Replace with Champion RCJ-6Y spark plug
and tighten securely with a 3/4 inch socket
wrench.
4. Reinstall the spark plug boot.
SERVICE AND ADJUSTMENTS
5. Insert ends of line one at a time through the
REPLACING THE LINE
line exit tunnels.
For unit to operate properly, the cutting line
should be replaced when line becomes worn to
less than 3 inches in length from the edge of the
line exit tunnels on each side of the cutting head.
6. Pull the line and make sure the line is ex-
tended fully through the tunnels.
WARNING: Only replace cutting line
with engine switch in the OFF position.
1. Remove and discard worn line before
installing new line.
2. Use only .115” diameter Weed EaterR
brand cut length line.
Line exit
tunnels
3. Insert one end of the line through the posi-
tioning tunnel.
7. Correctly installed line will be the same
length on both ends.
4. Continue to feed line through tunnel until
line is centered (leaving equal amounts on
each side). See illustration below.
Positioning
CARBURETOR ADJUSTMENTS
Your carburetor is equipped with limiter caps.
Carburetor adjustments is a complicated
task. We recommend that you take your unit
to an authorized service dealer. Damage will
occur if you turn the needles beyond the limit-
er stops.
tunnel
STORAGE
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to the gasoline
in the fuel tank or fuel storage container. Fol-
low the mix instructions found on stabilizer
container. Run engine at least 5 minutes after
adding stabilizer.
WARNING: Perform the following
steps after each use:
S Allow engine to cool, and secure the unit
before storing or transporting.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
ENGINE
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
S Store unit and fuel well out of the reach of
children.
SEASONAL STORAGE
S Clean air filter.
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy storage.
S Store in a clean dry area.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasoline to
oil ratio.
S Lightly oil external metal surfaces.
FUEL SYSTEM
OTHER
Under FUELING ENGINE in the OPERA-
TION section of this manual, see message la- S Do not store gasoline from one season to
beled IMPORTANT regarding the use of ga-
sohol in your engine.
another.
S Replace your gasoline can if it starts to rust.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing all of the
recommended remedies below except remedies that require operation of the unit.
TROUBLE
CAUSE
REMEDY
Engine will not
start.
1. Engine flooded.
1. See “Starting a Flooded Engine” in
Operation Section.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. See “Carburetor Adjustment” in
Service and Adjustments Section.
5. Carburetor requires
adjustment.
Engine will
not idle
properly.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. See “Carburetor Adjustment” in
Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Air filter dirty.
1. Clean or replace air filter.
2. Clean or replace plug
Engine will not
accelerate,
lacks power,
or dies under
a load.
2. Spark plug fouled.
and regap.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
Engine
1. Choke partially on.
1. Adjust choke.
smokes
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
excessively.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. See “Carburetor Adjustment” in
Service and Adjustments Section.
1. See “Fueling Engine” in Operation
section.
2. Replace with correct spark plug.
3. See “Carburetor Adjustment” in
Service and Adjustments Section.
4. Contact an authorized service dealer.
Engine runs
hot.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
up or normal adjustments explained in the op-
warrants to the original purchaser that each erator’s manual.
new Weed Eater brand gasoline tool or at- THIS WARRANTY GIVES YOU SPECIFIC
tachment is free from defects in material and LEGAL RIGHTS, AND YOU MAY HAVE
workmanship and agrees to repair or replace
under this warranty any defective gasoline
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
product or attachment as follows from the NO CLAIMS FOR CONSEQUENTIAL OR
original date of purchase.
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
2 YEARS -- Parts and Labor, when used for
household purposes.
60 DAYS -- Parts and Labor, when used for
commercial, professional, or income produc- SOME STATES DO NOT ALLOW LIMITA-
ing purposes.
TIONS ON HOW LONG AN IMPLIED WAR-
30 DAYS -- Parts and Labor, if used for rental RANTY LASTS OR THE EXCLUSION OR
purposes.
LIMITATIONS OF INCIDENTAL OR CON-
This warranty is not transferable and does not SEQUENTIAL DAMAGES, SO THE ABOVE
cover damage or liability caused by improper LIMITATIONS OR EXCLUSION MAY NOT
handling, improper maintenance, or the use APPLY TO YOU.
of accessories and/or attachments not spe- The policy of ELECTROLUX HOME PROD-
cifically recommended by ELECTROLUX
HOME PRODUCTS, INC., for this tool. Addi-
UCTS, INC., is to continuously improve its
products. Therefore, ELECTROLUX HOME
tionally, this warranty does not cover tune- PRODUCTS, INC., reserves the right to
ups, spark plugs, filters, starter ropes, starter change, modify, or discontinue models, de-
springs, cutting line, or rotating head parts signs, specifications, and accessories of all
that will wear and require replacement with products at any time without notice or obliga-
reasonable use during the warranty period.
This warranty does not cover predelivery set-
tion to any purchaser.
U.S. EPA / ENVIRONMENT CANADA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGA-
EATER cannot deny warranty solely for the lack
of receipts or for your failure to ensure the per-
TIONS: The U. S. Environmental Protection
Agency, Environment Canada and POULAN/ formance of all scheduled maintenance. As the
WEED EATER, DIVISION OF WCI OUT-
DOOR PRODUCTS, INC., are pleased to ex-
small off--road engine owner, you should be
aware that POULAN/WEED EATER may deny
plain the emissions control system warranty on you warranty coverage if your small off--road
your year 2001--2004 small off--road engine. engine or a part of it has failed due to abuse, ne-
POULAN/WEED EATER must warrant the
glect, improper maintenance, unapproved mod-
emission control system on your small off--road ifications, or the use of parts not made or ap-
engine for the periods of time listed below pro- proved by the original equipment manufacturer.
vided there has been no abuse, neglect, or im- You are responsible for presenting your small
proper maintenance of your small off--road en- off--road engine to a POULAN/WEED EATER
gine. Your emission control system includes authorized repair center as soon as a problem
parts such as the carburetor and the ignition exists. Warranty repairs should be completed in
system. Where a warrantable condition exists, a reasonable amount of time, not to exceed 30
POULAN/WEED EATER will repair your small
days. If you have any questions regarding your
off--road engine at no cost to you. Expenses warranty rights and responsibilities, you should
covered under warranty include diagnosis, contact your nearest authorized service center
parts and labor. MANUFACTURER’S WAR-
RANTY COVERAGE: If any emissions related
or call
POULAN/WEED EATER at
WARRANTY COM-
1--800--554--6723.
part on your engine (as listed under Emissions MENCEMENT DATE: The warranty period be-
Control Warranty Parts List) is defective or a de- gins on the date the small off--road engine is
fect in the materials or workmanship of the en- purchased. LENGTH OF COVERAGE: This
gine causes the failure of such an emission re- warranty shall be for a period of two years from
lated part, the part will be repaired or replaced the initial date of purchase. WHAT IS COV-
by POULAN/WEED EATER.
OWNER’S
ERED: REPAIR OR REPLACEMENT OF
WARRANTY RESPONSIBILITIES: As the
PARTS. Repair or replacement of any war-
small off--road engine owner, you are responsi- ranted part will be performed at no charge to the
ble for the performance of the required mainte- owner at an approved POULAN/WEED EAT-
nance listed in your instruction manual. POU- ER servicing center. If you have any questions
LAN/WEED EATER recommends that you
regarding your warranty rights and responsibili-
retain all receipts covering maintenance on your ties, you should contact your nearest authorized
small off--road engine, but POULAN/WEED service center or call POULAN/WEED EATER
9
Download from Www.Somanuals.com. All Manuals Search And Download.
at 1--800--554--6723. WARRANTY PERIOD:
failures of warranted parts caused by the use of
Any warranted part which is not scheduled for add--on or modified parts. HOW TO FILE A
replacement as required maintenance, or which CLAIM: If you have any questions regarding
is scheduled only for regular inspection to the ef- your warranty rights and responsibilities, you
fect of ”repair or replace as necessary” shall be should contact your nearest authorized service
warranted for 2 years. Any warranted part which center or call POULAN/WEED EATER at
is scheduled for replacement as required main- 1--800--554--6723. WHERE TO GET WAR-
tenance shall be warranted for the period of time RANTY SERVICE: Warranty services or re-
up to the first scheduled replacement point for pairs shall be provided at all POULAN/WEED
that part. DIAGNOSIS: The owner shall not be EATER service centers. Call 1--800--554--6723.
charged for diagnostic labor which leads to the MAINTENANCE, REPLACEMENT AND RE-
determination that a warranted part is defective PAIR OF EMISSION RELATED PARTS: Any
if the diagnostic work is performed at an ap- POULAN/WEED EATER approved replace-
proved POULAN/WEED EATER servicing cen-
ment part used in the performance of any war-
ranty maintenance or repair on emission related
ter. CONSEQUENTIAL DAMAGES: POU-
LAN/WEED EATER may be liable for damages parts will be provided without charge to the own-
to other engine components caused by the fail- er if the part is under warranty. EMISSION
ure of a warranted part still under warranty. CONTROL WARRANTY PARTS LIST: Car-
WHAT IS NOT COVERED: All failures caused
buretor, Ignition System: Spark Plug (covered
by abuse, neglect, or improper maintenance are up to maintenance schedule), Ignition Module.
not covered. ADD--ON OR MODIFIED
MAINTENANCE STATEMENT: The owner is
PARTS: The use of add--on or modified parts responsible for the performance of all required
can be grounds for disallowing a warranty claim. maintenance as defined in the instruction
POULAN/WEED EATER is not liable to cover manual.
The information on the product label indicates which standard your engine is certified.
Example: (Year) EPA Phase 1 or Phase 2 and/or CALIFORNIA.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|