TAILGATER™ BLENDER
TG15
For your safety and continued enjoyment of this product,
always read the instruction book carefully before using.
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Do not let cord hang over edge of table or counter, or
touch hot surfaces.
8. Keep hands and utensils out of jar while blending, to
prevent the possibility of severe personal injury and/or
damage to the blender. A rubber spatula may be used,
but must be used only when the blender is not running.
9. Blades are very sharp. Handle carefully.
ꢀ0. To avoid injury, never place blade assembly on the base
unless container is properly attached.
ꢀꢀ. Always operate blender with cover in place.
ꢀ2. For blending hot liquids, see “Hot Blending
Instructions,” next page.
ꢀ3. Screw on base collar firmly when assembling container.
Injury can result if moving blades accidentally become
exposed.
ꢀ4. Do not leave blender unattended while it is running.
SAVE THESE INSTRUCTIONS
2
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT:
HOT BLENDING INSTRUCTIONS
To minimize possibility of being scalded when blending hot
ingredients, the following precautions and procedures must
be observed:
ꢀ. Begin blending with no more than one cup (8 oz.) of
ingredients.
2. Before turning blender on, remove the center lid insert.
This will allow venting of the rapidly heated and
expanding air.
3. Start blending on low speed.
4. While blender is running, up to ꢀ½ cups (ꢀ2 oz.) of
additional liquid can be added. Pour liquid slowly
through the opening in the lid.
OPERATING INSTRUCTIONS
ꢀ. When placing the container on the unit base, make sure
that the unit is turned off and is at a complete stop.
Do not put the container on or take it off while the unit
is running. Doing so may damage the drive shaft or
blade assembly. For best results, do not fill container
above 3-cup level.
2. With the switch in the Off position, plug the blender
into a ꢀ2-volt cigarette lighter receptacle.
3. The Waring Pro® Tailgater™ Blender is ideal for blending
ice drinks. For best results, keep the blades covered
with liquid, turn the unit on, remove the lid insert, and
feed the ice cubes slowly into the container. NOTE:
Never use containers other than Waring Pro®
Blender containers with your unit.
4. For other blending tasks, put ingredients into container,
then put the lid on firmly. Always add liquid ingredients
first, unless otherwise specified in recipe. Always hold
container with one hand while blending.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ASSEMBLE CONTAINERS WITH
REMOVABLE BLADES
Always wash and rinse container prior to initial use.
ꢀ. Before starting, make sure that the blender cord is
unplugged and that the switch is in the Off position.
2. Refer to Figure ꢀ on page 5. The following points are
important to note when putting together the container
assembly:
• Container gasket must be placed between blade
assembly and container.
• Collar must be threaded properly onto the blender
container base, and securely tightened before placing
food or liquid in the container.
• To ensure proper assembly, place the blender
container upside down and turn the collar
counterclockwise until securely tightened.
3. Place assembled blender jar on unit base so that it is
firmly seated and not tilted to one side. Never place the
collar or blade assembly on the unit base unless the
container has been completely assembled and securely
tightened.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO DISASSEMBLE AND CLEAN
CONTAINERS WITH
REMOVABLE BLADES
Always wash and rinse container
immediately after use.
ꢀ. Be sure the switch is in the
Off position.
2. Remove the container
assembly from the unit base
and empty the contents.
3. To disassemble the Waring
Pro® Tailgater™ Blender, turn
container collar clockwise.
4. The collar, blade assembly and
gasket are dishwasher safe.
The plastic container lid and
insert must be washed by
Fig.ꢀ
hand. Allow all parts to air dry.
5. Be certain all components are in the proper position
when reassembling blender container and base.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO CLEAN UNIT BASE
ꢀ. To clean the unit base, unplug the power cord. Wipe the
exterior surfaces with a soft cloth or sponge dampened
with cleaning solution. Rinse with clean water. Do not
immerse the base in cleaning solution or water. Wipe
the base with dry towel.
FUSE REPLACEMENT
The plug on the blender power cord contains a replaceable
cartridge fuse. To gain access to the fuse, push the metal
tip of the plug inward as far as it will go, then turn it
counterclockwise until it releases. Withdraw the tip, with
the fuse attached, by pulling it straight out of the plug body.
Replace fuse with one of same size and rating (ꢀ5 Amperes,
32 Volts, Slow-Blow). Reassemble plug by reversing above
procedure.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
©2008
Waring Consumer Products
Division of Conair Corporation
ꢀ50 Milford Road
Printed in USA
TGꢀ5 Tailgater IB
08WR204
East Windsor, NJ 08520
028340
Download from Www.Somanuals.com. All Manuals Search And Download.
|