1,595 PSI Electric Pressure Washer
Item#3686-05
Model # QL-3100B
PLEASE READ AND SAVE ALL INSTRUCTIONS TO ENSURE THE SAFE AND
EFFECTIVE USE OF THIS TOOL.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
PLEASE READ AND SAVE THESE INSTRUCTIONS. Read carefully before
attempting to assemble, install, operate or maintain this product. Protect
yourself and others by observing all safety information. Failure to comply with
instructions could result in personal injury and/or property damage! Retain
instructions for future reference. Follow the safety warnings.
1. Read this manual carefully, know your equipment. Consider the applications,
limitations, and the potential hazards specific to your unit.
2. Outlets with a third prong ground are required. Do not use without a grounded
prong.
3. Do not touch plug or outlet with wet hands.
4. Avoid accidental starts. Move switch on unit to “OFF” position before connecting or
disconnecting cord to electrical outlets.
5. Water spray must never be directed towards any electrical wiring or directly towards
the pressure washer itself or fatal electric shock may occur.
6. Never carry your pressure washer by the cord. Do not pull on the cord to disconnect
from the outlet.
7. To prevent damage, the cord should not be crushed, placed next to sharp objects or
near a heat source.
8. Stay alert, watch what you are doing.
9. Follow maintenance instruction specified in this manual.
10.Check power cords before using. Damaged cords can reduce performance of
pressure washer or cause a fatal electric shock.
11.The narrow pin point stream is very powerful, it is not recommended for use on
painted surfaces, wood surfaces or items attached with adhesive backing.
12.Keep operating area clear of all persons.
13.To reduce the risk of injury, close supervision is necessary when this product is used
near children.
14.Always use both hands when operating pressure washer to maintain complete control
of wand.
15.Do not touch nozzle or water spray while operating.
16.Wear safety goggles while operating.
17.Always wear anti-slip shoes to prevent slipping.
SAVE THESE INSTRUCTIONS!
2
Download from Www.Somanuals.com. All Manuals Search And Download.
18.Disconnect power plug from the outlet when not in use and prior to the detaching of
the pressure hose.
19.Never tie knots or kinks the pressure hose as damage can result.
20.Prior to starting the pressure washer in cold weather, be sure ice has not formed in
any part of the appliance.
21.The pressure washer should not be used in areas where gas vapors may be present.
An electric spark can cause an explosion or fire.
22.To minimize the amount of water getting into the pressure washer, the motor
housing should be placed as far as possible from the cleaning site during operating.
23.To prevent accidental discharge, the spray gun should be secured by locking trigger
when not in use.
24.Do not operate this product when fatigued or under the influence of alcohol or drugs.
25.To allow free air circulation, the pressure washer should NOT be covered during
operation.
26.Know how to stop the product and bleed pressure quickly. Be thoroughly familiar
with the controls.
27.Do not over reach or stand on unstable support. Keep good footing and balance at
all times.
28.WARNING – Risk of injection or injury- Do not direct discharge stream at
persons.
29.This product is provided with a ground fault circuit interrupter built into the power
cord plug. If replacement of the cord or plug is needed use only identical
replacement parts. Tool service must be performed only by qualified repair
personnel. Service or maintenance performed by unqualified personnel could result
in a risk of injury.
GROUNDING INSTRUCTION
This product must be grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electric current to reduce the risk of electric
shock. This product is equipped with a cord having an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
DANGER
Improper connection of the equipment grounding conductor can result in risk of
electrocution. Check with a qualified electrician or service personnel if you are in doubt
whether the outlet is properly grounded. Do not modify the plug provided with the
product. If it will not fit the outlet have a proper outlet installed by a qualified
electrician. Do not use any type of adapter with this product.
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
This pressure washer is provided with a ground fault circuit interrupter (GFCI) built into
the plug of the power supply cord. This device provides additional protection from the
risk of electrical shock. Should replacement of the plug or cord become necessary use
only identical replacement parts that include GFCI protection.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY RULES
WARNING! Read, understand and save all instructions. Failure to follow all
instructions listed below may result in electric shock, fire or serious personal injury. The
warnings, cautions, and instructions discussed in this instruction manual cannot cover all
possible conditions and situations that may occur. It must be understood by the operator
that common sense and caution are a factor which cannot be built into this product, but
must be supplied by the operator.
SAVE ALL INSTRUCTIONS!
WORK AREA
1. Keep your work area clean and well organized. Cluttered benches and dark areas
invite accidents.
2. Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the
dust or fumes.
3. Keep bystanders, children and visitors away while operating a power tool.
Distractions can cause you to lose control.
ELECTRICAL SAFETY
Do not abuse the cord. Never use the cord to carry the tool. Keep cord away from heat,
oil, sharp edges or moving parts. Replace damaged cords immediately. Damaged cords
may create a risk of fire.
PERSONAL SAFETY
1. Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use tool while tired or under the influence of drugs, alcohol or
medication. A moment of inattention while operating power tools may result in
serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing and gloves away from moving parts. Wear protective goggles when
operating the machine. It is recommended to wear protective goggles, gloves, sturdy
non-slipping shoes and an apron.
3. Avoid accidental starting. Be sure switch is in OFF position before connecting to a
power outlet. Carrying tools with your finger on the switch when the switch is ON
invites accidents. Disconnect tool from power outlet before carrying out any work on
the machine.
4. Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enables better control of the tool in unexpected situations.
5. Use safety equipment. Always wear eye protection. Dust mask, non-skid safety
shoes, hard hat, or hearing protection must be used for appropriate conditions.
TOOL USE AND CARE
1. Do not force tool. Use the correct tool for your application. The correct tool will do
the job better and safer at the rate for which it is designed.
2. Do not use tool if switch does not turn ON or OFF. Any tool that cannot be controlled
with a switch is dangerous and must be repaired.
3. Place the switch in locked or OFF position before making any adjustments, changing
accessories or storing the tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users. They should be kept away from work
area.
5. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the tools operation. If damaged, have the tool serviced
before using. Many accidents are caused by poorly maintained tools.
6. Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may become hazardous when used on
another tool.
SERVICE
1. Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel could result in a risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow instructions in the
maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of electric shock or injury.
ELECTRICAL REQUIREMENTS
General Electrical Connections
DANGER: To reduce the risk of electrocution:
1. Use only identical replacement parts when servicing. Servicing should be
performed by a qualified service technician.
2. Do not use in rain or where floor is wet.
This tool is intended for indoor residential use only.
WARNING: Do not permit fingers to touch the terminals of plug when installing
or removing the plug to or from the outlet.
110-120 Volt, 60Hz. Tool Information
NOTE: The plug supplied on your tool may not fit into the outlet you are planning to
use. Your local electrical code may require slightly different power cord plug connections.
If these differences exist refer to and make the proper adjustments per your local code
before your tool is plugged in and turned on.
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electric current to reduce the risk of electric shock. This tool is equipped
with an electric cord having an equipment grounding conductor and a grounding plug, as
shown. The plug must be plugged into a matching outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Do not modify the plug provided. If it will not fit the outlet, have the proper outlet
installed by a qualified electrician.
A temporary adapter may not be used with this item.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRE SIZES
Make sure the proper extension cord is used and is in good condition. The use of any
extension cord will cause some loss of power. To keep this to a minimum and to prevent
overheating and motor burnout, use the table below to determine the minimum wire size
(A.W.G.) extension cord.
EXTENSION CORD
ƒ
Use only 3-wire extension cords which have 3-prong grounding type plugs and 3-
pole receptacles which accept the tools plug.
ƒ
Use only extension cords intended for outside use. These extension cords are
identified by a marking “acceptable for use with outdoor appliances, store indoors
while not in use.”
ƒ
ƒ
Use only extension cords having an electrical rating not less than the rating of
the product.
Do not use damaged extension cords. Examine extension cords before using and
replace if damaged.
ƒ
ƒ
ƒ
Do not abuse extension cord and do not yank on any cord to disconnect.
Keep cord away from heat and sharp edges.
Always disconnect the extension cord from the receptacles before disconnecting
the product from the extension cord.
WARNING: To reduce the risk of electrocution keep all connectors dry and off the
ground. Do not touch plug with wet hands.
Extension Cord Length
0-25 ft.
Gauge (A.W.G.)
12
10
25-50 ft.
SAVE THESE INSTRUCTIONS!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
LIST OF MAIN PARTS
PARTS DESCRIPTION
1. Motor Housing
2. Black Plastic Hooks
3. Handle
4. High Pressure Hose
5. Handle Frame
6. Gun Lance
7. Back Wheel
8. Soap Spray Bottle
9. Turbo Nozzle
10. Spray Nozzle
11. GFCI Power Plug
12. Power Cord
FIG. 1
13. Rubber Feet
14. Rubber Foot Screws
15. 7/8” Black Screws
16. Wheel Clips
17. Wheel Covers
18. Wheel Axle
19. Plastic Strap
20. Tip Cleaner
FIG. 2
21. Male high pressure
connector
22. Trigger Lock
23. Trigger
24. Female Screw Connector
FIG. 3
26. Male Screw Connector
27. Spray Nozzle
28. Turbo Nozzle
FIG. 4
7
Download from Www.Somanuals.com. All Manuals Search And Download.
29. Gun Lance Connecter
30. Pressure Washer
Connector
FIG. 5
31. Male High Pressure
Connector
32. Soap Spray nozzle
33. Soap Spray Bottle
FIG. 6
34. Over Load Switch
35. Power ON/OFF Switch
36. Water Inlet
FIG. 7
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS:
Model Number
Rating Voltage
Frequency
QL-3100B
100-120v
60Hz
Power
1500w
Protection category
Working Pressure
Max. flow
Max. Water temp.
Max. Pressure
Weight
IPX5
1500 PSI
1.58 gal./min
140°F
1595 PSI
40 Lbs
CONTENTS OF PACKAGING
a) Motor Housing with attached Pump
b) 2 Black Plastic Hooks
c) 1 Handle
d) 1 High Pressure Hose
e) 1 Handle Frame
f) 1 Gun Lance
g) 2 Back Wheels
h) 1 Soap Spray Bottle
i) 1 Turbo Nozzle
j) 1 Spray Nozzle
k) 2 Rubber Feet
l) 2 Rubber Feet Screws
m) 6 x 7/8” Black Screws
n) 2 Wheel Clips
o) 2 Wheel Covers
p) 1 Wheel Axle
q) 1 Plastic Strap
r) 1 Tip Cleaner
s) Instruction Manual
NOTE: Please refer to Page 7 FIG. 1 and FIG. 2 for photos of contents of packaging.
If any of the above items are missing, please contact our service department at 1-888-
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
1. Using a set of small pliers, attach a
wheel clip to one side of the wheel
axle.
FIG. 8
2. Tighten the wheel clip until you
hear a snap. The click sound
indicates that the wheel clip is
secured.
FIG. 9
3. From the opposite side of the wheel clip
slide one of the back wheels onto the
wheel axle.
4. Slide the wheel all the way to the end
of the wheel axle and stop at wheel
clip.
FIG. 10
5. Place a wheel cover on the end of
wheel and push down to secure.
FIG. 11
10
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Slide the wheel axle into the pressure
washer housing.
(Note: If wheel axle does not slide
easily try sliding wheel axle through the
other side of pressure washer housing
or try greasing the axle.)
FIG. 12
FIG. 13
FIG. 14
FIG. 15
7. On the other side of the pressure
washer housing pull the wheel axle all
the way out.
8. Place the wheel on the axle that is
sticking out from the pressure washer
housing.
9. Attach wheel clip to other side of wheel
axle. Tighten wheel clip. A click sound
indicates that the wheel is secured.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
10.Place wheel cover over wheel cap and
push down to secure.
FIG. 16
FIG. 17
FIG. 18
FIG. 19
11.Insert rubber foot screw into rubber
foot.
12.Screw rubber foot into pressure washer
housing. Note: Only tighten until it
feels snug. If over tightened the
screw will cut through rubber.
13.Wiggle rubber foot to be sure that it is
tightly secured.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
14.Place handle on top of motor housing.
FIG. 20
15.Insert handle frame on the opposite
side of handle.
FIG. 21
16.Screw 2 x 7/8” black screws into lower
pair of handle screw holes and secure.
FIG. 22
17.Insert black plastic hook into slot on
handle.
FIG. 23
13
Download from Www.Somanuals.com. All Manuals Search And Download.
18.Screw 2 x 7/8” black screws into holes
on the black plastic hook and secure
onto handle.
FIG. 24
FIG. 25
FIG. 26
FIG. 27
19.At the back of the motor housing attach
the second black plastic hook to
housing. Screw 2 x 7/8” black screws
into holes on the black plastic hook and
secure to motor housing.
20.Insert plastic strap into handle frame
until it ridges into the frame. No
screws are necessary.
21.Pull on plastic strap to check if strap is
secured.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
HIGH PRESSURE PIPE CONNECTION
ƒ
ƒ
ƒ
Connect the nozzle to the gun
lance by screwing it together.
FIG. 28
FIG. 29
FIG. 30
Screw the gun lance connector
into the gun lance.
Screw the pressure hose with
connector into the high pressure
outlet on the back of the pressure
washer.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTION OF THE WATER SUPPLY TO THE PRESSURE WASHER
ƒ
Connect the water supply to the water inlet on the front of the pressure inlet.
ƒ
Turn on water supply.
FIG. 31
LOCKING AND UNLOCKING THE TRIGGER ON THE GUN LANCE
The trigger lock is meant to prevent the unintentional discharge of the spray gun.
How to lock the trigger:
ƒ
ƒ
ƒ
Pull the handle forward
Slide the lock latch down to the arrow marked on the gun handle
Release the trigger
How to unlock the trigger:
ƒ
ƒ
ƒ
Pull trigger forward
Slide the locking latch so that the latch is flush next to the trigger
Release trigger
BLEEDING THE GUN
It is very important to bleed the gun before using the pressure washer. Squeeze the
trigger to allow any air that is trapped inside of the unit and hose to escape. Continue to
squeeze trigger until a steady stream of water comes from the nozzle. This process may
take up to 2 minutes.
ELECTRICAL CONNECTION OF THE APPLIANCE
The main voltage and the working voltage must correspond (see identification
plate on machine).
ƒ
Insert the GFI power plug into a power outlet (see GROUNDING INSTRUCTION,
page 3).
FIG. 32
16
Download from Www.Somanuals.com. All Manuals Search And Download.
How to turn on pressure washer:
ƒ
Operate the pressure washer in vertical position
only after connecting the water supply to the
water inlet and water supply has been turned on.
Switch power switch to ON.
ƒ
ƒ
Position the spray gun on the object to be
cleaned.
ƒ
ƒ
ƒ
NEVER SPRAY TOWARDS A PERSON!
Direct the nozzle downwards.
Fully press down the trigger and proceed with
cleaning.
FIG. 33
ON
OFF
Automatic ON/OFF:
The motor of this pressure washer does not run continuously. It only runs when the
trigger of the spray gun is squeezed. This feature will extend the lifetime of the motor
and prevent from overheating.
How to turn off the pressure washer:
ƒ
ƒ
ƒ
Switch power switch to OFF.
Turn off water supply.
Press the trigger to depressurize system.
How to use the accessories:
1. SPRAY NOZZLE- Adjustable Spray Nozzle can be adjusted to a pencil stream or
fan spray.
ƒ
Pencil Spray - A narrow stream has a high impact on cleaning surface
resulting in maximum deep cleaning in a concentrated area. However, this
narrow high impact spray must be used cautiously, as it may damage some
surfaces.
ƒ
Fan Spray – A wide fan pattern spray will distribute the impact of the water
over a larger area, resulting in excellent cleaning action with a reduced risk of
surface damage. Large surface areas can be cleaned more quickly using a
wide fan pattern.
FIG. 34
17
Download from Www.Somanuals.com. All Manuals Search And Download.
2. TURBO NOZZLE- Sometimes referred to as a rotary nozzle, is a very effective
tool that can significantly reduce cleaning time. The turbo nozzle combines the
power of a narrow high impact stream and the efficiency of a 25 degree fan
pattern. The turbo nozzle converts the narrow high impact stream into a cone
shaped pattern that cleans a larger area.
Please note: Since the turbo nozzle uses a narrow high impact stream,
only use it in applications where the cleaning surface cannot be
damaged. Additionally, the turbo nozzle is not adjustable and cannot be
used to apply detergent. Keep the spray lace at min. 6-8” away from the
cleaning surface at all times.
3. SOAP SPRAY BOTTLE- the following instructions are how to assemble and
operate the soap spray bottle.
Soap spray bottle assembly
1. Attach the high pressure
connector onto spray nozzle.
FIG. 35
2. Slide the high pressure
connector onto spray nozzle as
shown in FIG. 36.
FIG. 36
3. Twist high pressure connector
counter clockwise until you see
black tabs.
FIG. 37
4. Lock the high pressure connector
in place by pulling the nozzle
and connector apart.
FIG. 38
18
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Screw soap spray bottle onto
lance.
FIG. 39
Spray bottle operation- When cleaning with the pressure washer, some
cleaning tasks can be solved with water alone, but for most tasks it is
advantageous to use a detergent. A detergent ensures a quick soaking and
allows high pressure water to penetrate and remove the dirt more effectively.
ƒ
The detergents must not dry on the object being sprayed with pressure
washer.
ƒ
Use only detergents formulated for pressure washers. Pressure washer
detergents can be obtained at your local hardware store or automotive
store. Test detergent in an inconspicuous area before use.
How to clean surfaces and avoid damage
ANGLE TO CLEANING SURFACE
When spraying water against a surface, maximum impact is generated when the
water strikes the surface “head on”. However, this type of impact tends to cause
dirt particles to embed into the surface, thereby preventing the desired cleaning
action.
The optimum angle for spraying water against a cleaning surface is 45 degrees.
DISTANCE FROM CLEANING SURFACES
Another factor that determines the impact force of the water is the distance
between the spray nozzle and the cleaning surface. The impact force of the
water is increased as the nozzle is moved closer to the surface.
HOW TO AVOID DAMAGING SURFACES
Damaging to the cleaning surfaces occurs because the impact force of the water
exceeded the durability of the surface. Never use a narrow high impact stream
or a turbo nozzle on a surface that is susceptible to damage. Avoid spraying
windows with a narrow high impact stream or turbo nozzle as this my cause
breakage. The surest way to avoid damage to the surface are the following
steps:
1. Before triggering the gun, adjust the nozzle to a wide fan pattern.
2. Place the nozzle approximately 4-5 feet from and 45 degrees to cleaning
surface, and trigger the gun.
3. Vary the fan pattern spray angle and the distance to the cleaning surface
until optimum cleaning efficiency is achieved without damaging the
surface
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CAUTION: Before undertaking any work on the appliance always
turn power switch OFF and detach the plug from the power
socket.
Undertake only the maintenance operations described in the user instructions.
CLEANING
A clogged and partially clogged nozzle can cause a significant reduction of water coming
out of the nozzle and cause the unit to pulse while spraying.
To clean out nozzle:
ƒ
ƒ
Turn OFF and unplug unit.
Turn off water supply. Relieve any pressure trapped in the hose by squeezing
trigger 2-3 times.
ƒ
ƒ
ƒ
Separate lance from gun.
Rotate nozzle to the narrow stream setting. This opens up the fan blades.
Use included tip cleaner, or an unfolded paper clip, insert wire into the nozzle
hole and move back and forth until debris is dislodged.
Remove additional debris by back-flushing water through the nozzle. To do this,
place end of garden hose (with water running) to end of nozzle for 30-60
seconds.
ƒ
FIG. 40
STORAGE
Store the appliance in premises protected against freezing conditions.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING
Trouble
Possible Cause
Solution
Pressure drops or
oscillations
- Lack of water
- Nozzle is dirty
- Open the water tap
- Clean the nozzle of possible debris with tip
cleaner.
The motor hums when
switched on and fails to
start
- Main voltage too low
- Gun not activated
- Extension cord too
small
- Check the electrical connection
- Switch machine ON and operate the gun
- Use an extension cord of sufficient size
- Check the electrical requirements in safety
instructions (page 4)
The motor stops
- Overload cut-out,
disconnected due to
motor overheating
- Clogged injector
- Check to see if power voltage is correct.
Rest over load switch, wait 3 minutes and then
switch the appliance on again.
- Clean the soap injector by using the tip
cleaner
The detergent fails to
come out soap spray
bottle
Generates an irregular
and non-precise jet
- Dirty high pressure
nozzle in the spray
gun
- Clean the high pressure nozzle with the tip
cleaner
SERVICE CENTER
If you have any question in regards to the operation of this power tool or are in need of
a spare part please contact our service center at:
Wachsmuth & Krogmann, Inc.
Tel: 1-888-367-7373
(Business hours Mon-Fri 9:00am - 4:00pm CT)
ENVIRONMENTAL PROTECTION
If the tool should no longer work at all, please make sure that it is disposed in an
environmentally friendly way, by handing it into a public collection point. Please do not
put it with your household waste.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Thank you for purchasing a top quality KingCraft product. This Pressure
Washer item #3686-05 was tested and meets our stringent quality standards.
This product is warranted to be free from manufacturing defects in original
materials, including original parts, and workmanship until July 7th, 2006 or 1
year with proof of purchase.
The warranty is void if the defect is due to accidental damage, misuse, abuse,
neglect, improper repair or alteration by unauthorized persons or failure to follow
operation instructions provided with the product. This warranty does not apply to
commercial use.
The warranty is non-transferable and applies only to the original purchase and
does not extend to subsequent owners of the product. Liability under this
warranty is limited to repair, replacement or refund. In no event shall liability
exceed the purchase price paid by the purchaser of the product. Under no
circumstances shall there be liability for any loss, direct, indirect, incidental,
special or consequential damage arising out of in connection with use of this
product. This warranty is valid only in the United States of America. This Warranty
gives you specific legal rights. However you may have other rights that vary from
state to state. Some states do not allow limitation on implied warranties or
exclusion of consequential damages therefore these restrictions may not apply to
you.
In case you find the product to be defective please send it within the warranty
period to our service center. To avoid transport damages please send the product
in the original packaging. In return you will either receive your repaired item, a
new product or a refund. Please fill out the Warranty Card and send it together
with the product and purchase receipt
To arrange pick-up of the defective item please call our service center:
Wachsmuth & Krogmann Inc.
Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT)
Website: http://www.wk-usa.com
123 Sivert Court,
Bensenville,IL 60106,
USA
22
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY CARD
Electric Pressure Washer, item # 3686-05, model #QL-3100B
In case you find this product to be defective please send it within the
warranty period to our service center. To avoid transport damages please
send the product in the original packaging. In return you will receive your
repaired item, a new product or a refund.
This product is warranted to be free from manufacturing defects in
original materials, including original parts, and workmanship until July
7th, 2006 or 1 year with proof of purchase.
Please fill in your details below and send it together with the product and
purchase receipt. Please read the Limited Warranty conditions mentioned
in this instruction manual.
Customer Name
Street
City
State
ZIP Code
Purchase Date
Description of Defect :
To arrange pick-up of the defective item please call our service center:
Wachsmuth & Krogmann Inc.
Tel: 1-888-367-7373 (Business hours Mon-Fri 9:00am-4:00 pm CT)
Website: http://www.wk-usa.com
123 Sivert Court,
Bensenville,IL 60106,
USA
23
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDER FORM
FOR REPLACEMENT GUN LANCE, PRESSURE HOSE, SPRAY NOZZLE,
AND TURBO NOZZLE
Price per Gun Lance (includes shipping and handling $ 17.00)
Price per Pressure Hose (includes shipping and handling $ 14.00)
Price per Spray Nozzle (includes shipping and handling $ 10.00)
Price per Turbo Nozzle (includes shipping and handling $ 10.00)
Please send a MONEY ORDER only (no cash or personal checks) ,
payable to Wachsmuth & Krogmann Inc. to the following address:
Wachsmuth & Krogmann Inc,
123 Sivert Court
Bensenville, IL 60106
Kindly fill in your information below and send together with your
Money Order
Name
Street
City
State
ZIP
Date
Quantity of Item
Quantity of Item
Quantity of Item
Quantity of Item
Gun Lance @ $
Pressure Hose @ $
Spray Nozzle @ $
Turbo Nozzle @ $
Total amount
$
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|