INSTALLATION MANUAL
FLAT LCD DISPLAY MOUNT MODEL
WB-31 Swingout Arm Mount
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Warning Statements
WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MAXIMUM WEIGHT OF 50 LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BYA QUALIFIED SERVICE TECHNICIAN, AS
OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO.
FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN
DEATH.
WARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR
THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY
AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN
EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
Indicates that the power plug is to be disconnected from the power outlet.
Safety precautions must be taken at all times.
Warning and Caution statements.
A secure structure must support the weight, or load, of the display. When mounting to a wall that contains
wooden studs, dead center of the wooden stud must be confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result
in damage to the display and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure
to do so may result in damage to the display and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or damage can result from drop-
ping or mishandling the display.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any sur-
face other than wooden studs, use suitable hardware (which is commercially available).
Contact Orion Images with any technical/ installation questions.
Installation Instructions
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Parts List
NOTE:
This mount is shipped with all intallation hardware and components. Make sure that none
of these parts are missing and/ or damaged before beginning installation. If there are parts
missing and/or damaged, please stop and contact TOA Electronics, Inc.
200x200 ADAPTER HARDWARE
Swingout Arm (Qty 1)
M6 x 30mm Phillips Pan
Head Screws (Qty 4)
M6 x 20mm Phillips Pan
Head Screws (Qty 4)
1/4” Wedge Anchors
(Qty 4). These are used only
for concrete installations.
M6 x 12mm Phillips Pan Head
Screws (Qty 4)
M5 x 16mm Phillips Pan
Head Screws (Qty 4)
Mounting Backplate (Qty 1)
M5 x 12mm Phillips Pan
Head Screws (Qty 4)
M4 x 20mm Phillips Pan
Head Screws (Qty 4)
M5 Flat
Washer (Qty 4)
M6 x 35mm Set Screw
(Qty 1)
M4 Flat
Washer (Qty 4)
M4 x 10mm Phillips Head
Scews (Qty 4)
M4 x 16mm SEMS
Phillips Pan Head
Screw (Qty 4)
#14 x 2” Wood Screw
(Qty 4)
100x200 ADAPTER HARDWARE
200x200 Adapter Plate
(Qty 1)
M4 x 5mm Phillips Pan Head
Screws (Qty 4)
M4 x 6mm Phillips Pan Head
Screws (Qty 4)
100x200 Adapter Plate
(Qty 1)
M4 x 10mm Phillips Flat
Head Screws (Qty 6)
Installation Tools
Phillips Head Screw Driver Soft Material/ Blanket
1/2" Socket and Wrench
Level (Supplied)
Pencil
Tape Measure
Drill Gun
14mm Socket (Supplied)
Ratchet with 9/16” Drive Socket
M3 Allen Wrench (Supplied) Stud Finder (Commercially Available)
Page 4
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Backplate Installation - Wood Stud
NOTE:
These installation instructions will apply to the WB-31 Swingout Arm Mount.
The following steps will outline how the back plate will be mounted.
1. Determine where the mount location will be.
2. Use a stud finder (sold separately) to locate the nearest wall stud.
3. Once the wall stud has been located, dead-center of the wall stud must be determined.
4. After this has been determined, line-up the holes of the backplate.
NOTE: Be sure that the end of the back plate that has a “lip” is pointing down (Figure 1).
5. Use the provided wood screws to attach the back plate to the wall (Figure 2).
Figure 1. Backplate Mount
Figure 2. Backplate Installation
Installation Instructions
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Backplate Installation - Concrete Surface
NOTE: These installation instructions will apply to the WB-31 Swingout Arm Mount.
The following steps will outline how the back plate will be mounted.
1. Determine where the mount location will be.
2. After this has been determined, line-up the holes of the backplate.
NOTE: Be sure that the end of the back plate that has a lip is pointing as shown in (Figure 3).
3. Once the mounting holes are marked on the wall, use a 5/16” drill bit and drill 4 holes into the
concrete surface (Figure 3).
4. Once the holes have been drilled, gently tap the anchor studs into each hole, until the washer is flush
(even) with the concrete surface.
5. Place the backplate onto the concrete surface and slowly tighten each nut onto its respective anchor
stud (Figure 4).
Lip
Lip
Figure 3. Backplate - Concrete Surface
Figure 4. Backplate Installation - Concrete
Surface
Page 6
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
WB-31 Installation
1. The reverse side of the mount must be mounted to the back plate that is attached to the wall. The
back of the mount contains an elongated rectangle (Figure 5). Referring to Figure 5, the back plate
receptacle must be placed over the top of the back plate, so that the entire mount “hangs” on the
back plate.
2. Locate the access hole at the bottom of the mount base. Install the M6 x 35mm set screw with the
M3 Allen wrench.
3. Turn the Allen wrench clockwise (viewed from below) until the screw is secure.
WARNING: Failure to fully tighten the locking screw may result in possible damage to your
display.
NOTE:
In reference to Figure 5, the dash lines represent the back plate that is mounted to
an existing surface.
Figure 5. WB-31 Installation
Installation Instructions
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
(2) M4 x 10mm
Phillips screws
Display
(2) M4 x 10
Phillips screws
Figure 6. Monitor Installation
Installing the Monitor
1. Loosely tighten two (2) M4 x 10mm Phillips Head screws to the top of the mounting points.
2. Insert the head of the screws through the keyhole slots and then secure the bottom two (2)
M4 x 10mm Phillips Head screws to secure the flat panel to the mounts, then tighten the upper
M4 x 10mm Phillips Head screws (Figure 6).
CAUTION:
Do not over tighten the M4 x 10mm Phillips Head screws, or else damage to the
display may occur.
Cable Access
Please refer to Figure 7 for the correct way to route existing any cables.
WB-31 Articulating Swingout Arm - After the monitor has been mounted, remove the cable access plastic
Articulating Swingout Arm
Cable access
holes
Cable access
plastic covers
Figure 7. Cable Routing
Page 8
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Adjusting the Swingout Arm
This unit comes pre-tensioned at the factory. To adjust the swingout Arm so that there will not be any move-
ment, perform the following steps (Figure 8).
1. Remove the Plastic End Caps.
2. Take a 9/16” socket and ratchet and tighten the nut.
3. Tighten, or loosen, each joint to the user’s satisfaction.
4. Replace the Plastic End Caps.
NOTE: The mount shown in this illustration is
upside down to access the adjustment nuts.
caps
Bottom
Top
Adjustment
nuts
NOTE: The tilt/pivot adjustment nut is located
on the back of the tilt/pivot mount.
Figure 8. Swing Arm Adjustment
Installation Instructions
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Adapter Plate Installation
NOTE: If your flat panel is not a VESA 75/100, the 200x200 or the 100x200 Adapter Plates must be used.
100x200 Aapter Plate
1. Attach the 100x200 Adapter Plate to the back of the display using the provided hardware
(see Parts List, page 4).
2. Attach the WB-31 mounting plate to the back of the 100x200 using the M4 x 5 mm screws.
200x200 Aapter Plate
3. Figure 9B: Attach the 200x200 Adapter Plate to the back of the display using the provided
hardware (see Parts List, page 4).
4. Attach the WB-31 mounting plate to the back of the 200x200, or the 100x200 using the
M4 x 5 mm screws.
CAUTION: DO NOT OVERTIGHTEN THE SCREWS.
Mounting Hardware (Please refer to Page 4
for the correct mounting hardware that will
be used with your display.
100x200
Mounting Hardware (Please refer to Page 4
for the correct mounting hardware that will
be used with your display.
Display
Figure 9A
200x200
Display
Figure 9B
Page 10
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
Technical Specifications
Figure 11. WB-31 Swingout Arm
Installation Instructions
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
WB-31
E255449 29GZ
WALL MOUNT
IN-WB31.R2
Mfg. Date
PN
Page 12
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
|