F O O D S E R V I C E
Owner’s Manual
Read And Save These Instructions
®
BarBoss MP
Drink Machine MP
Maximum Performance Commercial Blender
All Models
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safeguards
Enjoy the safety of this grounded appliance. The Vita-Mix blender’s U.S. power cord
comes equipped with a three-prong (grounding) plug which mates with a standard three-
prong wall outlet (Figure A). This cord will vary for countries outside the United States.
Adapters (Figure B) are available for two-prong outlets. Do not cut or remove the
third (ground) prong from the plug or power cord.
Consult your electrician if you are not sure if the wall outlet is grounded through the
building wiring. With a properly grounded two prong wall outlet, ground the machine by
attaching the tab on the adapter to the wall outlet cover by means of the screw in the
center of the cover (Figure B).
THREE PRONG
ADAPTERS
ARE NOT TO
BE USED IN
Figure A
Figure B
CANADA.
Save These Safety Instructions
3
Download from Www.Somanuals.com. All Manuals Search And Download.
®
BarBoss MP &
Drink Machine MP Model
OFF
ON
ON/OFF switch. Located on the front of the
machine below the switch panel, controls the
power to the machine. With the machine plugged
in, switch the machine to ON to ready the
machine for blending. Shut OFF power switch
at night or whenever the machine will be left
unattended.
Note on Timers: Stop mid cycle with
START/STOP switch, not the
ON/OFF switch. If the ON/OFF
switch was used, wait 30 seconds for
power to recycle and the timer to
reset before resuming operation.
START TIMER switch. This is a lighted switch.
When light is lit power is ON. Depress START
TIMER switch to activate timer setting and again
to stop midcycle.
During operation, you may interrupt timer by
pressing START/STOP switch.
#5
#4
ax
M
#3
#2
TIMER DIAL. Allows user to select a number
of timed settings. Increments on timer are
approximate seconds. Timer is activated only
when the power switch is ON. Blender will shut
off automatically at the end of the pre-set time.
1
#
E
LS
PU
P
TO
R
S
E
T/
M
R
TI
TA
S
PULSE switch. Pulse button can only be used
when the power switch is ON. The PULSE
switch can be used to quickly refresh product
in the container by depressing the switch and
holding down as long as needed.
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and
clean in the groove around the water-shielded switches. You may also lightly spray
the surface around the switches with an all purpose cleaner (such as Cinch® or 409®)
and work the switches back and forth a few times to loosen any dried residue under
switch. Leaving switches sticky will damage or burn out the switches.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Outside the United States and Canada, your machine may come with a different
container configuration.
To secure lid plug, rotate it so one
tab locks between the stops on top
of rubber lid
Two-Part Lid
32 oz. (900 ml) Xtreme Performance Container
The two part lid is easy to clean and easy to put
Lift lid tabs
on, take off and seal.
to remove lid
• To remove a fully latched lid, lift the two
tabs and pull upward and off.
• Twist the center lid plug to fasten or
remove.
NOTE: Older 48 oz. (1.4 L) and 64 oz. (2.0 L)
Vita-Mix container will work on the BarBoss or
Drink Machine MP. The Xtreme Performance
Containers will not work on older Vita-Mix
Machines. Call Vita-Mix or your distributor for
more information.
Figure A
One Piece Lid (optional)
32 oz. (900 ml) Xtreme Performance Container
The one piece lid is easy to clean and easy to put
on, and take off and seal.
Figure B
• There is no lid plug for this lid.
• Add ingredients through port on top.
NOTE: To make new lids easier to insert and remove, rub a light coating of cooking oil
around bottom where it seals. Place it in container for several minutes, remove and
lightly wipe oil off lid.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
®
BarBoss MP & Drink Machine MP Instructions
1. Set the container on the motor base by aligning it over the centering pad anchored to
the base. (Motor must be completely stopped before positioning container). Containers
are not to be used for hard, dry materials. Avoid running your machine with the container
empty.
2. Place liquids and soft foods in the container first, solid items and ice last. Prepare
food by cutting or breaking into 1-3 inch (3-8 cm) pieces. Frozen fruit should be as small
as practical.
3. Always use lid when blending. If blending hot ingredients, the lid must be securely in
place. When processing hot liquids, DO NOT use a non-latching lid.
4. Press ON/OFF switch to ON. Activate the timer by selecting the desired setting
on the dial and then depressing the START/STOP TIMER switch on the left.
NOTE: Each setting on the dial (#1 - #5 and MAX Blend) is an increase in time and
speed. Your own testing will determine what setting will work best for your drinks.
4a. If mixture stops circulating, you have likely trapped an air bubble. Either insert the
tamper through the lid while blending, or stop the motor remove the container from
the base and stir or scrape the mixture from the sides of container into the center
using a rubber spatula to press any air bubbles away from the blades. Replace the
lid and continue blending.
Note: START/STOP TIMER switch on your machine is lit when power is ON. Avoid
moveable parts. The timer stops working if machine is overloaded on low speed.
Reset the machine by turning power OFF for 15 seconds.
Warning: If you detect a change in the sound of the machine or if a hard or
foreign object comes into contact with the blades, do not serve the drink.
Inspect your blade assembly for loose, nicked or missing parts. If parts are
loose, missing, or nicked replace with new blade assembly. (See page 8.)
4b. To prevent possible splashing, lightly rest your hand on the lid while turning the
machine on (except when processing hot liquids).
4c. Due to the blending speed of the machine, processing times are greatly reduced
over standard machines. Until you become accustomed to the speed, watch your
mixture carefully to avoid over-blending.
4d. If stopping the machine mid-cycle, use the START/STOP switch, not the POWER
switch. If the POWER switch was used, wait 30 seconds for power to recycle and
the timer to reset before resuming operation.
5. After blender has been turned off, wait until blade comes to a complete stop before
removing the lid or container from the motor base.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The thermal protector shuts the motor off to protect it from overheating. To restart,
wait for motor to cool down with the power OFF (up to 30 minutes). When this happens,
review your processing techniques and your instructions. Your recipes may be too thick
or have too much material in them.
Cooling may be quickened by placing the motor base in a refrigerator or a cool spot.
Unplug first. To speed up the process try circulating the air with a vacuum or fan aimed
at the bottom of the base. If the motor seems to be over heating (and the thermal
overload protector has not turned the machine OFF), remove the container from the
base. Set the timer for 20 seconds. Turn the machine ON and let the machine run for
20 seconds. Repeat this step 3 times for a total of 1 minute.
6. To use the PULSE switch: Press ON/OFF switch to ON. With the container on the
motor base depress the PULSE switch. Release the switch to turn off the motor.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Agitator Assembly. Blades are sharp; use
caution when handling the blade. When inserting the
blade assembly through the container bottom, align the
flat sides. Gravity holds it in place while the retainer nut
is tightened. Do not attempt to disassemble this part.
Drive Spline. Mates with drive socket on the motor
base to turn the blade. Note: Removing and replacing
your container while the coupling is still rotating will
strip the drive spline “teeth”. (This part is NOT
removable.)
32
Retainer Nut. Must be snug. Order the available
retainer nut wrench for best results. (Refer to the
diagram below to remove or replace.)
Never use a blade assembly with loose, damaged or nicked components.
Blade Assembly Removal
CAUTION: Do not remove blades unless absolutely necessary!
At times, it may be necessary to give your blades additional
cleaning. An easy-to-use blade assembly removal wrench
(Item #15596) may be purchased through your Vita-Mix
distributor. Never attempt to take the blade assembly itself
apart. This will void the warranty.
Retainer Nut Wrench
Turn the container upside down and grip firmly. Insert retainer
nut wrench in groove of retainer nut and rotate counterclock-
wise to loosen. Then grip blades with a cloth and remove
retainer nut by hand.
Replacing Blade Assembly
With the container upside down, grip blades with cloth, insert
into the container bottom and align with flat sides of container
Retainer Nut Wrench
in use.
opening. Place retainer nut on and hand tighten. Last, carefully
turn clockwise until secure, using wrench. Do not force. If it is
not tight enough, you will notice increased container noise.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
The Accelerator Tool prevents an air bubble
from forming while blending. It is used when
making frozen ice creams, pureeing fruits
and vegetables, (or whenever your mixture
requires it). It also permits you to push
ingredients down around the blades while
the Vita-Mix blender is running.
Accelerator Tool use:
• Use only with the lid in place and the
center lid plug removed.
• The splash disc prevents the Accelerator
Tool from hitting the blades when insert-
ed through the lid.
• Container should not be more than
2/3 full (just below the indicated
maximum capacity for XP containers)
when the Accelerator Tool is left in place
while blending.
• To avoid overheating, do not exceed
30 seconds of continuous blending
with Accelerator Tool in place.
8
4
• If thick mixtures stop circulating, you
have likely trapped an air bubble.
Insert Accelerator Tool through the lid
and stir to release it.
• Holding the Accelerator Tool at an angle
near the side and pushing towards the
center will be more effective when
creating a thicker, smoother drink.
*NOTE: Accelerator Tools have a small step
on them. The step prevents the Accelerator
Tool from coming into contact with the blades
in Vita-Mix polycarbonate containers.
Accelerator Tool cannot be used with a one
piece non-latching lid.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Care Note
To ensure that you get the longest possible life from your Vita-Mix product, we recom-
mend the following products, when used as directed by the supplier:
Cleaning Product. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier
Solid Supra, Solid Power,.. . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN
Guardian Acclaim, Solid Guardian Plus, . . . . . . . . . . . . . (800) 352-5326
Diverpak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI
Eclipse H2, Liqui-Safe L7 . . . . . . . . . . . . . . . . . . . . . . . . (800) 521-8140
Acclean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Klenzade Products
Poly-Brite . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Division of Ecolab
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . St. Paul, MN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (612) 293-2165
Glow MB-1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wesmar Company, Inc.
Lustre NC-25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seattle, WA
Lustre Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (206)783-5344
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.wesmar.com
PSRA 41-D, PSRA 41-E . . . . . . . . . . . . . . . . . . . . . . . . . Anderson Chemical Co.
Liqui-Ware 1, Liqui-Ware MC . . . . . . . . . . . . . . . . . . . . . Litchfield, MN
D-Flex, Sur-Met . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 366-2477
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . www.andersonchemical.com
Rinse Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier
Solid Rinse Dry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ecolab, Inc., St. Paul, MN
Solid Brilliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 352-5326
Destainer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Supplier
NuWare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Diversey, Livonia, MI
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (800) 521-8140
Do not use abrasive cleaning agents or concentrated bleach
when cleaning. Do not use any cleaners containing Quatinary Sanitizers
on polycarbonate components (i.e., containers).
NOTE: Switches will become sticky from use. Use a wet cloth or sponge to flush and
clean in the groove around the water-shielded switches. You may also lightly spray the
surface around the switches with an all-purpose cleaner (such as Cinch® or 409®) and
work the switches back and forth a few times to loosen any dried residue under switch.
Dirty switches may burn out.
ADDITIONAL NOTE: Do not let mixtures, liquids and food products dry within the
container. Rinse throughout use. Drying may lock around the blade and weaken/tear
the bearings seal when restarted. Do not place containers in the freezer. Extremely
low temperature combined with hot ingredients and/or the immediate rapid action of the
blade may crack the container. Due to the nature of polycarbonates, microwaving and
automatic dishwashing are not recommended. Follow the cleaning instructions on page 11.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Motor Base
1. Unplug the power cord.
2. Wash outside surface with a damp, soft cloth or sponge, which has been rinsed in a
mild solution of liquid dish soap (Ivory Liquid® or equivalent) in warm water. NEVER
IMMERSE MOTOR BASE IN WATER OR OTHER LIQUID.
3. Thoroughly clean switches so that they work freely. They will become sticky from
use. Use a wet cloth or sponge* to flush and clean in the groove around the water
shielded switches. You may also lightly spray the surface around the switches with
an all-purpose cleaner such as Cinch® or 409® and work the switches back and forth
a few times to loosen any dried residue under switch.
4. Polish with a soft cloth.
*Note: Be sure to wring excess water out of cloth or sponge when cleaning around the
controls or any electrical part.
Lid
Separate the lid and plug, then wash in warm soapy water. Rinse clean under running
water and dry. Reassemble before use. (See page 5).
Container
1. To clean: Fill pitcher 1/4 full with warm (110˚F/43˚C) water and add a couple drops
of dish soap.** Return container to motor base and firmly position the two part lid.
Run machine for 30 seconds. Empty container. Repeat this step.
** Note: To prolong polycarbonate container life, Vita-Mix recommends using soaps
with a low Ph balance, such as a manual pot and pan detergent. Due to the nature
of polycarbonates, automatic dishwashing is not recommended.
2. Fill pitcher 3/4 full with warm (110˚F/43˚C) water (do not add soap). Return container
to motor base and firmly position the two part lid. Run machine for 30 seconds.
Empty container.
3. If any solid residue remains, remove the blade agitator assembly (see page 8) and
wash all container parts in warm soapy water. Rinse and drain. Reassemble before
next step.
4. To sanitize: If all solid residue is gone after step 2 or after completion of step 3,
fill container 3/4 full with a sanitizing solution mix.*** Return container to motor base
and firmly position the two part lid. Run machine on HIGH for 30 seconds. Empty
container.
5. Return container to motor base and run machine empty for an additional 5 seconds.
Do not rinse after sanitizing.
*** Recommended sanitizing solution: 1-1/2 teaspoons institutional or household
bleach in 2 quarts (2 liters) water.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
®
BarBoss MP & Drink Machine MP
NOTE: Outside the United States and Canada, your machine may come with a different
container configuration. Contact your local Vita-Mix distributor for part numbers.
Item # Part
#760
#15578
PLS209
#891
Accelerator tool
Sound-reducing XP centering pad
Variable speed control knob / timer control knob
Drive socket
XDM039
#15585
#15598
#15571
Owner’s Manual
XP retainer nut
XP blade agitator assembly
32 oz. (900 ml) polycarbonate Xtreme Performance container with lid
and lid plug
#15574
#15570
#15573
2-piece thermoplastic rubber lid for 32 oz. (900 ml) Xtreme
Performance container
32 oz. (900 ml) polycarbonate stackable Xtreme Performance
container, ice blade & lid assembly
32 oz. (900 ml) polycarbonate stackable Xtreme Performance
container only
*Notice: Other than the drive socket, blade assembly and retainer nut, this unit
is not user serviceable.
#755
#15574
#15575
#15596
#15573
Retainer Nut Wrench
(sold separately)
OUNCES
48
40
32
#15571
#15598
#15585
#891
#PLS145
One-Piece Lid
(sold separately)
#15578
PLS209
#760
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Top four problems you can fix on your own
1. Problem:
Solution #1:
• increased vibration
• leaking from bottom of container
• increased container noise
Check blade assembly for loose, damaged
or nicked components and replace.
Solution #2:
Tighten retainer nut with screwdriver
moving clockwise until it is snug. See p. 8.
2. Problem:
• Machine will not run.
Solution #1:
Double-check to make sure power cord is
firmly in power outlet.
Solution #2:
Check to make sure switches are clean
and moving freely.
Solution #3:
The thermal protector may have turned
the machine OFF. Turn power OFF for up
to 30 minutes to reset. Note: Cooling may
be quickened by placing the motor base in
a refrigerator or cool spot. (Unplug first).
To speed up the cooling process, try circu-
lating the air with a fan or vacuum at the
bottom of the motor base.
3. Problem:
Solution:
• loud noise from blade area
• blades don’t spin
Drive socket may be broken. Check for a
fine crack down the center or worn teeth-
replace with a new drive socket. (Item #891).
Instructions are included with part.
4. Problem:
Solution:
• Machine will not run when START
TIMER switch is activated.
Check ON/OFF switch to make sure the
switch is in the ON position. Note: START
TIMER switch is lit when power is on.
Timer stops working if machine is overloaded on low speed. Reset by turning power
OFF for 15 seconds. Do not turn power OFF midway through a blending cycle.
To interrupt cycle, press START/STOP TIMER switch one time. See page 4.
If you cannot fix your machine with these suggestions, technical help is available by
calling 800-4DRINK4 (800-437-4654). If outside the United States and Canada,
contact your local Vita-Mix distributor or phone the Vita-Mix International Division at
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Vita-Mix Corporation warrants your Commercial Vita-Mix appliance to be free from
defects in materials and workmanship for a period of three years from the date of
purchase when used in accordance with the accompanying instruction booklet.
Provisions of this limited warranty are void if your Vita-Mix appliance has been
subjected to obvious abuse, negligence, accident, alteration, or failure to follow
operating instructions, or product exposure to abnormal or extreme conditions.
Cosmetic changes such as discoloration of parts of the product in the hands of the
user or the effects of the use of abrasive cleaners will not be warranted or considered
defects. The cleaning or removal of food products along with any damage caused by
allowing them to build up is not covered by this limited warranty. Warranty is void if
the Vita-Mix blender is put into a sound reduction chamber that does not allow
proper cooling.
In the event your Vita-Mix appliance needs service or repair covered by the terms of
this warranty, please call the Vita-Mix Corporation for shipping instructions. The Vita-Mix
blender must be sent in original or sufficient packaging.
This limited warranty is in lieu of any other warranty expressed or implied. No
representative or any other person is authorized to make any other warranty or to
assume any liability not strictly in accordance with the foregoing. This limited warranty
gives you specific legal rights which may vary from state to state. Proof of purchase
may be required to prove date of purchase.
Outside the Continental United States and Canada other warranties may apply.
(Call or check with your local Vita-Mix distributor for details). In case of shipping damage,
notify the shipper or carrier immediately. Outside the United States and Canada, contact
your local Vita-Mix Distributor.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PLEASE NOTE: The Service Contract outlined in the following paragraphs applies
only to customers in the United States and Canada. Customers in all other countries
should contact their local Vita-Mix® distributor for service details.
This Vita-Mix blender includes a 1-Year Service Contract effective from date of
purchase. In the event your machine should need parts or repairs, covered under this
Service Contract, call Vita-Mix customer service immediately for instructions. Proof of
date of purchase may be required. This does not cover abuse, misuse, tampering,
improper installation or extreme conditions.
The Vita-Mix Service Contract includes the following:
1. Only one extra drive socket - to facilitate simple repairs and prevent down time is
included and packaged with each machine.
2. Additional drivers and accelerator tool, unless defective, are not covered. NOTE: to
determine if you have a defective part, please order a replacement part through
Vita-Mix Customer Service and, when the new part arrives, return the old part in the
same packaging. Vita-Mix will inspect the returned part and, if defective, issue a
refund for the price of the new part. A part will be considered defective if no abuse or
neglect was involved with its break. Non defective parts sent to Vita-Mix for inspection
will not be returned if deemed unusable. Service Contract covers functionality of the
machine but not abuse or lack of recommended maintenance.
3. In the continental United States, sender pays freight one way to Vita-Mix
Corporation. The Vita-Mix Corporation will pay UPS ground freight charges to return
the machine to the sender. Sender pays costs for special shipping requests. Outside
Continental United States, other service contracts may apply.
Before returning this product for any reason, including repair, please, first contact our
CUSTOMER SERVICE DEPARTMENT: (800) 4DRINK4, (800) 437-4654 or (440) 235-0214
to receive a “RETURN AUTHORIZATION NUMBER”.
Note: Within the United States, Limited Warranty and Service Contract are honored
directly through the Vita-Mix Corporation, Cleveland, Ohio USA. Non-warranty repairs
can be performed by any CFESA service center. For machines sold in the USA, call
Vita-Mix (800) 4DRINK4 (800-437-4654) or (440) 235-0214.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dimensions:
Height of Motor Base: 8-1/2” (21.25 cm)
• with 32 oz. (900 ml) polycarbonate Xtreme Performance container
and lid: 18” (45.72 cm)
• with 32 oz. (900 ml) polycarbonate Xtreme Performance container
without lid: 16” (40.64 cm)
32 oz. (900 ml) polycarbonate Xtreme Performance container with lid,
no base: 10-3/4” (27.31 cm)
Dimensions: 8” W x 9” D x 18” H (20.3 cm x 22.9 cm x 45.72 cm)
Ship weight of machine: 13 lbs. (6 kg)
Power Requirements:
Volts: 120 VAC
Amps: 11.5
Hz: 50/60
Volts: 220/240 VAC
Watts: 750-850
Hz: 50/60
Volts: 100 VAC (Japan)
Watts: 900
Hz: 50/60
NSF
®
N
When applicable:
The instructions appearing in this Owner’s Manual cannot cover every possible
condition and situation that may occur. Common sense and caution must be
practiced when operating and maintaining any appliance.
VITA-MIX® CORPORATION
Foodservice Division
8615 Usher Road, Cleveland, Ohio 44138-2103 USA
©2005 Vita-Mix Corporation. No part of this publication may be reproduced or transmitted in any form or
by any means, electronic or mechanical, including photocopy, recording or any information storage and retrieval system
without the written permission of the Vita-Mix Corporation.
Printed in U.S.A.
XDM039 11/05
Download from Www.Somanuals.com. All Manuals Search And Download.
|