V I S I O N F I T N E S S
A s s e m b l y
G u i d e
M O D E L S X 6 2 0 0 H R C / D A & X 6 0 0 0 D A
D U A L - A C T I O N E L L I P T I C A L T R A I N E R S
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS & HARDWARE INCLUDED
MM
5 Allen Wrench
BLUE BAG
MM
13 Wrench
Screwdriver
MM
M8 x 45 Bolt
Quantity: 2
MM
M8 x 80 Bolt
Quantity: 4
MM
M8 x 13 Nylock Nut
Quantity: 4
MM
5 L-Shaped Wrench
MM
MM
BLACK BAG
19 D x 440 L Rear Folding Axle
Quantity: 1
(not shown to scale)
MM
M8 x 16 Bolt
3
Quantity: 4
Download from Www.Somanuals.com. All Manuals Search And Download.
ORANGE BAG
PINK BAG
8 x 17 X 1.5T Washer
Quantity: 2
MM
M8 x 16 Bolt
16 x 22 x .3T Spring Washer
Quantity: 2
Quantity: 2
8 x 15 X 2T Lock Washer
Quantity: 4
MM
MM
16 x 28 x 1.5T Washer
Quantity: 2
5/16” x 30 x 1.5T Washer
Quantity: 2
M8 x 60 Bolt
M5 x 25 Bolt
Quantity: 2
Quantity: 1
GREEN BAG
MM
MM
M7 x 35 Bolt
Quantity: 2
M8 x 12 Bolt
Quantity: 2
MM
MM
M8 x 25 x 1.5T Washer
Quantity: 2
M16 x 22 x .3T Spring Washer
Quantity: 2
M8 x 13 Nylock Nut
Quantity: 4
M8 x 12 Bolt
Quantity: 2
MM
13 Nut Caps
M26 x 34 x .3T Spring Washer
Quantity: 2
M8 x 35 x 2T Washer
Quantity: 2
Quantity: 2
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
1
STEP
1
BLACK BAG
• Install the left and right stabilizers
MM
with the four bolts (M8 x 16 ), using
MM
the Blue 5 Allen wrench.
• Cover both stabilizers with the
included rubber boots.
• Insert the rear folding axle shaft
MM
MM
(440 L x19 D) into the rear tube.
STEP
ORANGE BAG
2
STEP
2
• Slide a spring washer (M16 x .3T)
onto the right-hand side of the rear
folding axle, followed by the right-
hand pedal arm guide rail (the guide
rails each have a blue indicator arrow
printed on their sides; these arrows
should face to the outside).
• Slide a flat washer (M16 x 1.5T)
onto the right-hand side of the rear
axle, followed by a rear wheel.
• Slide the large flat washer
(5/16” x 1.5T) onto the right-hand
side of the rear axle, and secure with
MM
a bolt (M8 x 16 ).
• Repeat above steps to install left-
hand pedal arm guide rail.
STEP
3
STEP
3
BLUE BAG
• Mount the rear pedal arms to the
front pedal arms using four bolts
MM
MM
(M8 x 80 ) and four 13 NyLock
MM
nuts, using the 13 wrench.
• Install the foot toe pieces to the front
MM
pedal arms with two bolts (M8 x 45 )
MM
using the Blue 5 Allen wrench.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
4
STEP
PINK BAG
4
• X6000 only: Unfold the RPM sensor
wire, located in the frame console
mast bracket. Remove any kinks.
• All models: Slide the rubber console
mast cover onto the bottom of console
mast, and slide it up as far as it will
go.
X6000DA
OR
• X6000 only: Holding the console
mast above the frame bracket, guide
the RPM sensor wire and lower
magnet cable up through the console
mast while simultaneously sliding the
console mast onto the frame bracket.
X6200HRC/DA
• All models: Bolt the console mast
to the frame bracket with two bolts
MM
(M8 x 60 ), two flat washers
(8 x 17 x 1.5T), and two lock washers
(8 x 15 x 2T). Tighten with the Blue
MM
5
Allen wrench. Slide the rubber
console mast cover back down over
the bolt heads. X6000 NOTE: Be sure
the RPM sensor wire exits through the
small slot at the top right side of the
the console mast.
• X6000 only: Mount console to
console mast, using the two screws.
Plug the RPM sensor wire into the
back of the console, and feed the
excess back down into the small slot
in the console mast.
• X6000 only: Turn the tension knob
to Level 15. Reach inside the console
mast and connect the magnet cables.
Turn the knob to Level 1 and mount the
MM
knob using a bolt (M5 x 25 ).
• X6200 only: Remove the four
screws from the back of the console.
Plug the wire connector from inside
the mast into the console. The cable
connector is slotted, so it may only be
connected one way; do not force it!
• X6200 only: Mount the console to
the mast using the four screws. Do not
pinch the cable!
• All models: Bolt the water bottle
cage to the console mast using the
two bolts located in the mast.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
STEP
GREEN BAG
5
• Slide a large spring washer
(M26 x 34 x .3T) onto the console
mast axle. Locate and slide the right
upper handlebar bracket onto the
console mast axle and attach with a
STEP
5
MM
washer (M8 x 35 x 2T) and 13
MM
NyLock nut, using the 13 wrench.
MM
Snap the plastic 13 nut caps over
the nuts.
• Slide a small spring washer
(M16 x 22 x .3T) onto the lower
pedal arm support, followed by the
right lower arm. Attach with a washer
(M8 x 25 x 1.5T) and bolt (M8 x 12),
MM
using the Blue 5 Allen wrench.
• Pivot the lower arm and insert the
top end into the upper handlebar
bracket. Attach with bolts (M7 x 35)
and (M8 x 12) through the side, and
bolts (M8 x 16) from the front. Tighten
MM
using the Blue 5 Allen wrench.
• Repeat the above steps to attach the
left-hand upper and lower arms.
the vision to succeed
621-D East Lake Street
•
P.O. Box 280
•
Lake Mills. WI 53551
fax 1.920.648.3373
toll free 1.800.335.4348
•
phone 1.920.648.4090
•
2000 Vision Fitness. All Rights Reserved. 8.00 Part #Z60EP08-AG1801PRD
AG18.01PRD
REV1
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|