4. Locate the two memory expansion slots in the open compartment.
Notice the location of the off-center keys on the expansion slots. There
may be a standard memory module already occupying one or more of the
expansion slots. If you
need to remove an exist-
ing memory module
Viking Memory
I N S T A L L A T I O N G U I D E
HITACHI®
VisionBook Plus & VisionBook Pro
before continuing with
this upgrade, please pro-
ceed to step 5. If you do
not need to remove a
memory module, please
proceed to step 6.
5. To remove a memory mod-
ule, locate the retaining clips
on both sides of the module.
Gently pull both clips away
from the module. Then lift the
module out of its expansion
slot.
6. To install a memory module,
insert the module into the expan-
sion slot at an angle and then push
it down until it clicks into place.
To be certain that the module is
installed correctly, ensure that the
off-center notch on the module is
aligned with the off-center key of
the expansion slot. The module
can only be installed one way due
to the position of the notch.
Manual No. 1005210 • Release 05/98, Rev. B
S P E E D
P O W E R
P E R F O R M A N C E
The Hitachi VisionBook Plus comes standard with 16MB of removable
memory. It can be expanded to a maximum of 128MB by installing the
following Viking Components memory options into its two available
expansion slots.
The Hitachi VisionBook Pro comes standard with 16MB of memory sol-
dered or 32MB (16MB soldered + 16MB memory module). It can be
expanded to a maximum of 144MB by installing the following Viking
Components memory options into its two available expansion slots.
7. Replace the memory expansion cover and be sure to secure its holding
screw.
Description
Viking P/N
8. Replace the battery back into its compartment.
8MB Memory Module
16MB Memory Module
32MB Memory Module
64MB Memory Module
HI4010, RHI4010
HI4011, RHI4011
HI4012, RHI4012
HI4013, RHI4013
9. Replace the AC power supply and any other cables you may have dis-
connected.
10. Turn unit right-side up and turn the system on. The computer auto-
matically detects the added memory and gives the following error mes-
sage: “Warning, Unexpected Amount of Memory, run SCU.” Go to BIOS
Setup, Save and Reboot. The new memory can be verified during the
POST routine at start-up and at the SETUP utility.
The installation is now complete.
WARRANTY & DISCLAIMERS:
Caution:
Electro Static Discharge (ESD) can damage electronic components. Before
touching the memory module, ensure that you are discharged of static elec-
tricity by touching a grounded metal object.
All Viking Components products have been thoroughly tested free of defects in materi-
al and workmanship. If any malfunction should occur while using one of our products
in its recommended environment, Viking, at its option, will repair or replace the prod-
uct at no charge, provided the product or any part thereof has not been abused, misused,
neglected, replaced, repaired or modified. Viking shall make the final determination as
to the existence and the cause of any defect. Viking will not repair or replace products
designated as having a “Limited Lifetime” which fail solely because their estimated life
has expired. No warranty is made with respect to customer products produced to orig-
inal purchaser specifications except as specifically stated in writing by Viking.
INSTALLATION INSTRUCTIONS:
1. Turn the computer off and disconnect the AC power supply and any
other cables from the unit.
Note: If the unit appears to be powered
down, ensure that it is not in Suspend mode.
All shipping costs shall be the responsibility of the purchaser.
Except as provided herein, there are no express or implied warranties of merchantabili-
ty or fitness for a particular purpose. Under no circumstances will Viking Components
be liable in any way to the purchaser for any damages, including but not limited to lost
revenue, lost wages, or any other incidental or consequential damages arising out of the
use of or inability to use this product. Viking reserves the right to make modifications
in both hardware and software without prior notifications.
2. Turn the computer upside-down. Remove
the battery from the system. If you are not
familiar with this procedure, please refer to
your computer’s “Owner’s Manual.”
3. Locate the memory expansion cover towards
the front of the bottom panel. Also locate the
holding screw on the cover. Remove the screw
with a small Phillips-head screwdriver. Then
remove the cover by lifting it up.
All Viking Components are 100% guaranteed compatible with the OEM machines for
which they are designed. All OEM's names, trademarks and part numbers are used for
identification purposes only, and in no way imply that any of our products are original
equipment parts.
Hitachi, VisionBook and Traveler are registered trademarks of Hitachi PC Corporation.
Copyright 1998 Viking Components, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|