®
ViewSonic
- User Guide
- Guide de l’utilisateur
- Bedienungsanleitung
- Guía del usuario
- Guida dell’utente
- Guia do usuário
- Användarhandbok
- Käyttöopas
Pro8400
DLP Projector
- Руководство пользователя
- 使用手冊 (繁體)
- 使用手册 (简体)
- 사용자 안내서
IMPORTANT: Please read this User Guide to obtain important
information on installing and using your product in a safe
manner, as well as registering your product for future service.
Warranty information contained in this User Guide will describe
your limited coverage from ViewSonic Corporation, which is
English, or in specific languages using the Regional selection
box in the upper right corner of our website.
- คู่มือการใช้งาน
- Podręcznik użytkownika
- Kullanιcι kιlavuzu
“Antes de operar su equipo lea cuidadosamente las
instrucciones en este manual”
Model No. : VS13647
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this unit near water.
Clean with a soft, dry cloth.
Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8.
9.
Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade and the third prong are provided
for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure that the
power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the unit. When a cart is used, use caution when
moving the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the unit
has been damaged in any way, such as: if the power-supply cord or plug is damaged,
if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or
moisture, or if the unit does not operate normally or has been dropped.
ViewSonic Pro8400
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/95/EC of the
European Parliament and the Council on restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum
concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:
Proposed Maximum
Substance
Actual Concentration
Concentration
Lead (Pb)
0.1%
0.1%
0.01%
0.1%
0.1%
0.1%
< 0.1%
< 0.1%
< 0.01%
< 0.1%
< 0.1%
< 0.1%
Mercury (Hg)
Cadmium (Cd)
6+
Hexavalent Chromium (Cr
)
Polybrominated biphenyls (PBB)
Polybrominated diphenyl ethers (PBDE)
Certain components of products as stated above are exempted under the Annex of the RoHS Directives
as noted below:
Examples of exempted components are:
1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not
specifically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic ceramic
parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up
to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.
ViewSonic Pro8400
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright Information
Copyright© ViewSonic® Corporation, 2010. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are
trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material, or
the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available, please
provides an opportunity for you to print the registration form, which you may mail or fax to ViewSonic.
For Your Records
Product Name:
Pro8400
ViewSonic DLP Projector
VS13647
Model Number:
Document Number:
Serial Number:
Purchase Date:
Pro8400_UG_ENG Rev. 1A 09-16-10
_______________________________
_______________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the environment. Please use
care and dispose of in accordance with local, state or federal laws.
ViewSonic respects the environment and is committed to working and living green. Thank you for being
part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
3. Taiwan: recycle.epa.gov.tw/recycle/index2.aspx
ViewSonic Pro8400
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Configuration ..................................62
Focus .............................................23
Controlling the projector through a LAN
environment ...................................36
Controlling the projector through a web
browser ..........................................39
....................................................... 45
Displaying pictures with a USB storage
device .............................................51
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Projector Features
The projector integrates high-performance optical engine projection and a user - friendly
design to deliver high reliability and ease of use.
The projector offers the following features:
„
„
„
„
„
„
„
„
„
„
„
„
„
Single chip 0.65" Texas Instruments DLP® technology
1080p (1920 x 1080 pixels)
Compatibility with Macintosh® computers
Compatibility with NTSC, PAL, SECAM and HDTV
D-Sub 15-pin terminal for analog video connectivity
User-friendly, multi-language on-screen display
Advanced electronic keystone correction
RS-232 connector for serial control
HDMI compatibility
TM
PJLink compatible
LAN display for network control and web server
LAN display 4-1 (maximum 4PC/ NB display to 1 projector)
Remote desktop feature for LAN and USB display 1-M (maximum 1PC/ NB can
display to 8 projectors at the same time)
„
„
„
USB display supports computer connection via USB mini-B type to A type cable
USB Reader supports USB flash drive via USB A type connector
Less than 1 W power consumption in standby mode
„
„
The information in this manual is subject to change without notices.
The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Package Contents
When you unpack the projector, make sure you have all these components:
HDMI1
Video
HDMI2
Compo
PC
Swap
Default
Projector with Lens Cap
AC Power Cord
Remote Control (IR) & batteries
VGA Cable (D-SUB to D-
HDMI Cable
ViewSonic CD
Wizard
Quick Start
Guide
SUB)
Optional accessories
Filter cover
P/N: P4R34-4600-00
RS232 cable
P/N: J2552-0208-00
RGB to component adapter
P/N: J2552-0212-00
ViewSonic Pro8400
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector Carrying Case
„
„
Contact you dealer immediately if any items are missing, appear damaged, or if
the unit does not work
Save the original shipping carton and Packing material; they will come-in
handy if you ever to ship your unit. for maximum protection, repack your unit as
it was originally packed at the factory.
.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Projector Overview
Front View
12
11 10
9
13
1
2
4
5
6
7
8
3
Lens cap
Filter cover
Speaker
8
1
2
3
4
5
6
7
Elevator button
Elevator foot
9
Focus ring
Zoom ring
Control panel
Lamp cover
10
11
12
13
Lens cap strap
Projection lens
Front IR remote control sensor
Ventilation holes (intake)
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Rear View
2
3
4
6
1
5
Connection ports
1
2
3
4
5
6
AC power socket
Kensington lock
Rear IR remote control sensor
Speaker
Ventilation holes (exhaust)
Bottom View
3
1
2
Ceiling mount holes (M4*8)
Tilt-adjustment feet
Security bar
1
2
3
„
„
This projector can be used with a ceiling mount for support. The ceiling mount is
not included in the package.
Contact your dealer for information to mount the projector on a ceiling.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Using the Product
Control Panel
9
1
2
3
4
8
5
6
10
7
4
Power (Power LED indicator)
Refer to “LED Indicator Messages”.
TEMP (Temperature LED indicator)
Refer to “LED Indicator Messages”.
LAMP (Lamp LED indicator)
Refer to “LED Indicator Messages”.
Keystone/Arrow keys ( /Up,
Manually correct distorted images resulting from an angled projection.
1
2
3
4
5
/Down)
Four directional buttons
Use four directional buttons to select items or make adjustments to your selection.
ENTER
6
Enter to sub-menu and confirm the menu selection.
SOURCE
7
8
Display the source selection bar.
MENU/EXIT
Display or exit the on-screen display menus.
Power
9
Turn the projector on or off.
Right/Panel key
10
Activate panel key lock.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Connection Ports
2
3
6
7
8
9
1
5
4
18
17
16
14 13 12
10
11
15
RS-232
1
When operating the projector via a computer, connect this to the controlling
computer's RS-232C port.
Monitor Out
2
3
4
5
6
Connect to a computer display, etc.
Component (Y Cb/Pb Cr/Pr)
Connect Y Cb/Pb Cr/Pr output from video equipment to this jack.
S-Video
Connect S-Video output from video equipment to this jack.
USB B
USB display supports computer connection via USB mini-B type to A type cable.
USB A
This connector supports firmware update, USB flash drive display and wireless
dongle for USB display.
LAN
7
For LAN display/network control and web server.
HDMI 1
8
9
Connect HDMI output from video equipment to this jack.
HDMI 2
Connect HDMI output from video equipment to this jack.
DC 12V Out
12V DC out
10
11
MIC in
Microphone input jack.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Audio Out
12
13
14
15
16
17
18
Connect to a speaker or other audio input equipment.
Audio 2
Connect an audio output from video equipment or computer to this jack.
Audio 1
Connect an audio output from video equipment or computer to this jack.
Audio 3 (L/R)
Connect an audio output from video equipment to this jack.
Video
Connect composite video output from video equipment to this jack.
Computer in 2
Connect image input signal (analog RGB or component) to this jack.
Computer in 1
Connect image input signal (analog RGB or component) to this jack.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Remote Control
Power
1
Turn the projector on or off.
HDMI 1
13
14
15
16
17
2
Display HDMI 1 signal.
HDMI1
Video
HDMI2
Compo
PC
Video
3
3
4
Switch input source to Composite/
S-Video by sequence.
Up/Volume +,
Volume -
When the On-Screen Display
(OSD) menu is not activated,
adjust the projector’s sound level.
Down/
4
5
5
4
18
19
20
21
22
23
24
6
7
Left/Mute
When the On-Screen Display
(OSD) menu is not activated, this
button is used as mute function.
8
Swap
9
10
11
12
Menu
6
7
Default
Display on-screen display menus.
25
User 1
Recall the customized settings
based on the current available
settings.
HDMI 2
15
16
Function
User definable key for customized
function.
Gamma
Change the gamma setting.
8
9
Display HDMI 2 signal.
PC
Switch input source to Computer in 1/
Computer in 2 by sequence.
Enter
17
18
Pattern
10
11
Confirmed selections.
Display embedded test pattern.
Right/ Lock
Color Mode
Change the image mode setting
by sequence.
When the On-Screen Display (OSD)
menu is activated, the #4, #5, and #18
keys are used as directional arrows to
select the desired menu items and to
make adjustments.
Blank
12
Cut off the screen temporarily.
Press again to cancel the Blank
Screen function.
Activate panel key lock.
Light
13
14
ESC
19
Enable backlight functions of the
remote control’s buttons.
Leave current page or items or to close
OSD.
Compo
Display Component video (YPbPr/
YCbCr) signal.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
13
User 2
Aspect
23
24
20
Recall the customized settings
based on the current available
settings.
Select the display aspect ratio.
RGBCMY
Change indivial RGBCMY color (user
color setting).
PIP/POP
Switch screen to PIP/POP by
sequence.
21
22
Default
25
Restore settings to factory default.
Swap
Swap input source in PIP or POP
image.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Installing the Batteries
1.
2.
3.
Open the battery cover in the
direction shown.
Install batteries as indicated by the
diagram inside the compartment.
Close the battery cover into
position.
Caution
„ Risk of explosion if battery is replaced by an incorrect type.
„ Dispose of used batteries according to the instructions.
„
Make sure the plus and minus terminals are correctly aligned when loading a battery.
„
Keep the batteries out of the reach of children. There is a danger of death by
accidentally swallowing the batteries.
„
„
Remove batteries from remote control when not using for extended periods.
Do not dispose of the used batteries along with household waste. Dispose of used
batteries according to local regulations.
„
„
„
Danger of explosion may happen if batteries are incorrectly replaced. Replce all
the batteries with new ones.
Batteries should not be in or near to fire or water, keep batteries in a dark, cool
and dry place.
If suspect battery leakage, wipe out the leakage and then replace new batteries.
If the leakage adheres to your body or clothes, rinse well with water immediately.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Remote Control Operation
Point the remote control at the infrared remote sensor and press a button.
„
Operating the projector from
the front
„
Operating the projector from
the rear
6m
8m
„
„
Do not point the laser directly to the people's eyes (especially small children).
There is a danger of injury to the eyes.
The remote control may not operate when there is sunlight or other strong
light such as a fluorescent lamp shining on the remote sensor.
Operate the remote control from a position where the remote sensor is visible.
Do not drop the remote control or jolt it.
Keep the remote control out of locations with excessively high temperature or
humidity.
„
„
„
„
„
Do not get water on the remote control or place wet objects on it.
Do not disassemble the remote control.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
or
11
3
1
1
2
9
9
9
7
7
8
6
10
5
4
12
VGA cable (D-Sub to D-Sub)
VGA to DVI-A cable
S-Video cable
1
7
Composite Video cable
Audio cable
8
9
2
3
4
5
6
USB cable (mini-B type to A type)
VGA (D-Sub) to HDTV (RCA) cable
Component Video cable
Audio L/R cable
HDMI cable
10
11
12
Microphone 3.5 mini jack cable
USB flash drive
Important
„ In the connections shown above, some cables may not be included with the
available from electronics stores.
„ The connection illustrations above are for reference only. The rear
connecting jacks available on the projector vary with each projector model.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1.
Take the supplied VGA cable and connect one end to the D-Sub output socket of
the computer.
2.
Connect the other end of the VGA cable to the Computer in 1 or Computer in 2
signal input socket on the projector.
Important
„ Many notebooks do not turn on their external video ports when connected to
a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the
external display on/off. Locate a function key labeled CRT/LCD or a function
key with a monitor symbol on the notebook. Press FN and the labeled
function key simultaneously. Refer to your notebook's documentation to find
your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen,
you can connect the Monitor Out signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1.
Connect the projector to a computer as described in “Connecting a computer” on
2.
Take a suitable VGA cable (only one supplied) and connect one end of the cable
to the D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
Connect the other end of the cable to the Monitor Out socket on the projector.
Important
3.
„ The Monitor Out output only works when Computer in 1 or Computer in 2
is made to the projector.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one
of the following output sockets:
„
„
„
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the
above connecting methods, however each provides a different level of video quality.
The method you choose will most likely depend upon the availability of matching
terminals on both the projector and the Video source device as described below:
Best video quality
The best available video connection method is Component Video (not to be confused
with composite Video). Digital TV tuner and DVD players output Component Video
natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) Video.
the projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite
Video. If you have both composite Video and S-Video output terminals on your Video
source device, you should elect to use the S-Video option.
projector to an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less
than optimal result from your projector, being the least video quality of the available
methods described here.
projector to a composite Video device.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component
Video output sockets available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to a Component Video source device:
1.
Take a VGA (D-Sub) to HDTV (RCA) cable, Component Video cable or a
Component Video to VGA (D-Sub) adaptor and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device.
Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
2.
If you are using the VGA (D-Sub) to HDTV (RCA) cable and the Component Video
to VGA (D-Sub) adaptor, connect the other end of the cable (with a D-Sub type
connector) to the Computer in 1 or Computer in 2 socket on the projector. If you
are using the Component Video Cable, connect the other end of 3RCA type
connectors to the Y Cb/Pb Cr/Pr sockets on the projector.
Important
„ If the selected video image is not displayed after the projector is turned on
and the correct video source has been selected, check that the Video source
device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
„
RGB to component adapter (ViewSonic P/N: J2552-0212-00)
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output
socket available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the
Video source device.
2.
Connect the other end of the S-Video cable to the S-Video socket on the
projector.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Important
„ If the selected video image is not displayed after the projector is turned on
and the correct video source has been selected, check that the Video source
device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
„ If you have already made a Component Video connection between the
projector and this S-Video source device using Component Video
connections, you need not connect to this device using an S-Video
connection as this makes an unnecessary second connection of poorer
details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite
Video output sockets available:
„
„
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the
device.
To connect the projector to a composite Video source device:
1.
Take a Video cable and connect one end to the composite Video output socket of
the Video source device.
2.
Connect the other end of the Video cable to the Video socket on the projector.
Important
„ If the selected video image is not displayed after the projector is turned on
and the correct video source has been selected, check that the Video source
device is turned on and operating correctly. Also check that the signal cables
have been connected correctly.
„ You need only connect to this device using a composite Video connection if
Component Video and S-Video inputs are unavailable for use. See
“Connecting Video source devices” on page 19 for details.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Operation
Powering On/Off the Projector
Powering On the Projector:
1.
2.
3.
Remove the projector lens cap.
Complete the AC power cord and peripheral signal cable(s) connections.
Press
to turn on the projector.
The projector takes a minute or so to warm up.
Turn on your source (computer, notebook, DVD, etc.). The projector automatically
detects your source.
4.
„
If you are connecting multiple sources to the projector simultaneously, press
SOURCE on the projector to select your desired signal or press your desired
signal key on the remote control.
Warning
„ Remove the lens cap first before powering on.
„ Never look into the lens when the lamp is on. This can damage your eyes.
„ This focal point concentrates high temperature. Do not place any object near
it to avoid possible fire hazard.
Powering Off the Projector:
1.
Press
Press Power again" appear on the screen.
Press again to confirm.
to turn off the projector lamp. You will see a message "Power off?
2.
„
„
The cooling fans continue to operate for cooling cycle.
When the Power LED begins flashing, the projector has entered stand-by
mode.
„
If you want to turn the projector back on, you must wait until the projector has
completed the cooling cycle and has entered stand-by mode. Once in stand-
by mode, simply press
to restart the projector.
3.
4.
Disconnect the AC power cord from the electrical outlet and the projector.
Do not turn on the projector right after power off.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Adjusting the Projector Height
Tilt-adjustment feet
Elevator foot
Elevator button
The projector is equipped with an elevator foot to adjust the image height.
To raise or lower the image:
1.
To raise or lower the image, press the elevator button and raise or lower the front
of the projector. Release the button to lock the adjustment.
To level the image on the screen, turn the tilt-adjustment feet to fine-tune the
height.
2.
„
To avoid damaging the projector, make sure that the elevator foot and tilt-
adjustment feet are fully retracted before placing the projector in its carrying
case.
Adjusting the Projector Zoom and Focus
Zoom ring
Focus ring
1.
2.
Focus the image by rotating the focus ring. A still image is recommended for focusing.
Adjust the image size by sliding the zoom ring.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Adjusting Projection Image Size
Refer to the graphic and table below to determine the screen size and projection distance.
Maximum zoom
Minimum zoom
Screen
Center of lens
Vertical offset
Projection distance
16 : 9 Screen
Projection distance [inch (m)]
Screen size
Diagonal
[inch (cm)]
Image
height [inch
(cm)]
Vertical
offset
[inch (cm)]
(min. zoom)
(max. zoom)
30 (76)
40 (102)
50 (127)
60 (152)
80 (203)
100 (254)
120 (305)
150 (381)
200 (508)
220 (559)
250 (635)
300 (762)
35 (0.89)
48 (1.21)
60 (1.52)
72 (1.83)
97 (2.46)
122 (3.09)
146 (3.72)
183 (4.66)
246 (6.24)
270 (6.87)
307 (7.81)
369 (9.38)
55 (1.39)
74 (1.87)
14.7 (37)
5.0 (12.8)
19.6 (50)
6.7 (17.1)
93 (2.35)
24.5 (62)
8.4 (21.4)
111 (2.83)
149 (3.79)
187 (4.75)
224 (5.7)
29.4 (75)
10.1 (25.6)
13.5 (34.2)
16.8 (42.7)
20.2 (51.3)
25.2 (64.1)
33.6 (85.4)
37.0 (94.0)
42.0 (106.8)
50.5 (128.2)
39.2 (100)
49 (125)
58.8 (149)
73.5 (187)
98.1 (249)
107.9 (274)
122.6 (311)
147.1 (374)
281 (7.14)
376 (9.54)
413 (10.5)
470 (11.94)
564 (14.33)
„
Position the projector in a horizontal position; other positions can cause heat
build-up and damage to the projector.
„
„
Keep a space of 30 cm or more between the sides of the projector.
Do not use the projector in a smoky environment. Smoke residue may build-
up on critical parts and damage the projector or its performance
.
„
Consult with your dealer for special installation such as suspending from a
ceiling.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings
from being changed accidentally (by children, for example). When the Panel Key
Lock is on, no control keys on the projector will operate except
Power.
1.
2.
Press
on the projector or remote control.
A confirmation message is displayed. Select
HDMI1
Video
HDMI2
Compo
PC
Yes to confirm.
To release panel key lock, press and hold
3 seconds on the projector.
for
Swap
Default
Important
„ Keys on the remote control are still functional when panel key lock is
enabled.
„ If you press
Power to turn off the projector without disabling panel key
lock, the projector will still be in locked status the next time it is turned on.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Menu Operation
The projector has multilingual on-screen display menus that allow you to make image
adjustments and change a variety of settings.
Brightest, Standard, Theater 1,
Theater 2, ViewMatch, User1,
User2
Color Mode
Saturation
Sharpness
Tint
Video Setting
Color Temp.
User, LOW, MID, HIGH
0 - 100
Red Gain
0 - 100
Green Gain
Blue Gain
0 - 100
Red, Green, Blue,
Cyan, Megenta, Yellow
Color
Hue
-100 - +100
-100 - +100
-100 - +100
Saturation
Gain
-5 - +5
Video/Audio
-10 - +10
-10 - +10
Overscan
Noise Reduction
Audio Setting
0% - 10%
Off, LOW, MID, HIGH
Computer 1
Computer 2
Video Source
HDMI 1
Audio in 1, Audio in 2, Audio in 3
Audio in 1, Audio in 2, Audio in 3
Audio in 1, Audio in 2, Audio in 3
Audio in 1, Audio in 2, Audio in 3, HDMI
Audio in 1, Audio in 2, Audio in 3, HDMI
HDMI 2
0 - 10
0 - 20
Microphone Volume
Speaker Volume
Mute
ViewSonic Pro8400
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Auto Keystone
Keystone
-30 - +30
Auto, 4:3, 16:9, 16:10,
ANAMORPHIC 1,
ANAMORPHIC 2
Aspect Ratio
Front-Table, Front-Ceiling,
Rear-Table, Rear-Ceiling
Filter Mode*2
High Altitude
Quick Power On
Quick Power Off
DC 12V Trigger
Input Password
Password Delete
Black, Red, Green, Blue,
Cyan, Yellow, Magenta, White
OSD Setting
Top-Left, Bottom-Left, Center,
Top-Right, Bottom-Right
OSD Timeout
20 - 60
0, 10, 20, 30, 40, 50, 60, 70, 80, 90
OSD Transparency
Off, CC1, CC2, CC3, CC4, T1, T2
Message
Others
Zoom
DCR
Test Pattern
Off, PIP, POP
Yes, No
Display Type
Swap
Function*3
ViewSonic Pro8400
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Disconnect, Connect
On, Off
Status
Wired LAN
NetWork
Default Gateway
DNS
Apply
Disconnect, Connect
Status
Wireless LAN
SSID
SSID Display
On, Off
Connection Mode
AP, Infrastructure
On, Off
Apply
Network Restart
Input Source
Yes, No
Computer 1, Computer 2,
Component, Composite,
Information
S-Video, HDMI, USB 1, USB 2
MAC Address
Filter Hours*2
Filter Hours Reset*2
Equivalent Lamp Hours
Equivalent Lamp Hours
Reset
Factory Default
*1 Adjustable range and default setting vary depending on signal type.
*2 This function is only available when the projector is installed an optional filter cover.
*3 The selectable Function list includes Color Mode, Gamma, Overscan, Noise
Reduction, Keystone and Filter Mode.
ViewSonic Pro8400
28
Download from Www.Somanuals.com. All Manuals Search And Download.
How to operate
1.
2.
3.
Press MENU on the projector or Menu on the remote control to open the OSD menu.
When OSD is displayed, use to select any feature in the main menu.
S
/
T
After selecting the desired main menu item, press
setting.
X
to enter sub-menu for feature
4.
5.
Use
S
/
T
to select the desired item and adjust the settings with
W
/
X.
Press MENU on the projector or Menu on the remote control, the screen will return to
the main menu.
6.
To exit OSD, Press MENU on the projector or Menu on the remote control again. The
OSD menu will close and the projector will automatically save the new settings.
Picture
Color Mode
There are many factory presets optimized for various types of images.
„
„
„
„
„
„
„
Brightest
Standard
Theater 1
Theater 2
ViewMatch
User 1
:
:
:
:
:
:
:
For the brightest environment.
For computer or notebook.
For home theater.
For home theater.
For accuracy color performance.
Memorize user 1 defined settings.
Memorize user 2 defined settings.
User 2
Brightness
Brighten or darken the image.
Contrast
Set the difference between light and dark areas.
Video Setting
Allow you to enter the Video Setting menu.
„
„
„
Saturation: Adjust a video image from black and white to fully saturated color.
Sharpness: Sharpen or soften the image.
Tint: Shift colors toward red or green.
Color Setting
Adjust the color temperature. At higher temperature the screen looks colder; at lower
temperature, the screen looks warmer. If you select “User”, then you can change the
intensity of each of 3 color (Red, Green, Blue) to customize user color temperature.
User Color
User Color provides six sets (RGBCMY) of colors to be adjusted. When you select each
color, you can independently adjust its range and saturation according to your preference.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look
brighter.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Video/Audio
Frequency
Adjust the timing of the projector relative to the computer.
Tracking
Adjust the phase of the projector relative to the computer.
H Position (Horizontal Position)
Adjust the image left or right within the projection area.
V Position (Vertical Position)
Adjust the image up or down within the projection area.
Overscan
Remove noise around the video image.
Noise Reduction
Reduce temporal and/or spatial noise in the image.
Audio Setting
Allow you to enter the Audio Setting menu.
„
„
„
„
Computer 1: Select the audio input for Computer in 1 signal.
When Audio in 1 is turned on, Audio in 2 and Audio in 3 will turn off automatically.
Computer 2: Select the audio input for Computer in 2 signal.
When Audio in 2 is turned on, Audio in 1 and Audio in 3 will turn off automatically.
Video Source: Select the audio input for video source.
When Audio in 3 is turned on, Audio in 1 and Audio in 2 will turn off automatically.
HDMI 1: Select the audio input for HDMI 1 signal.
„
„
„
„
When HDMI 1 is turned on, Audio in 1, Audio in 2 and Audio in 3 will turn off
automatically.
„
HDMI 2: Select the audio input for HDMI 2 signal.
„
When HDMI 2 is turned on, Audio in 1, Audio in 2 and Audio in 3 will turn off
automatically.
Microphone Volume
Adjust the microphone’s volume level.
Speaker Volume
Adjust the projector’s volume level.
Mute
Cut off the sound temporarily.
Setting
Auto Keystone
Automatically correct distorted images resulting from an angled projection.
ViewSonic Pro8400
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Keystone
Manually correct distorted images resulting from an angled projection.
„
When adjusting the Keystone, Auto Keystone will be set at "Off" automatically.
Aspect Ratio
Select how the picture fits on the screen:
„
„
„
„
„
„
Auto : Scales an image proportionally to fit the projector's native resolution in its
horizontal or vertical width.
4:3
:
Scales an image so that it is displayed in the center of the screen with a 4:3
aspect ratio.
16:9 : Scales an image so that it is displayed in the center of the screen with a 16:9
aspect ratio.
16:10: Scale an image so that it is displayed in the center of the screen with a 16:10
aspect ratio.
ANAMORPHIC 1: Scale an image so that it is displayed in the center of the screen
with a 1.85:1 aspect ratio.
ANAMORPHIC 2: Scale an image so that it is displayed in the center of the screen
with a 2.35:1 aspect ratio.
Projection
Adjust the picture to match the orientation of the projector: upright or upside-down, in front of
or behind the screen. Invert or reverse the image accordingly.
Power Saving
If the input source is not detected and no operation is performed for a specific period of time,
projector will automatically turn off.
Auto Source
Automatically scan through all the input source.
Signal Type
Specify the source to the Computer in 1/Computer in 2 terminal that you wish to project.
„
Auto
: Automatically detect the input signal type from Computer in 1 and Computer
in 2 terminals.
„
„
RGB : For VGA signal
YCbCr/YPbPr:For component signal
ECO Mode
Use this function to dim the projector lamp light output which will lower power consumption
and increase lamp life.
„
This function will be unavailable when the DCR function is on.
Filter Mode
Use this function to activate filter mode after the projector is installed an optional filter cover.
High Altitude
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Use this function to allow the fans operates at full speed continuously to achieve proper high
altitude cooling of the projector.
Quick Power On
Enable the projector to turn on automatically after the power cord has been connected
and power has been applied.
Quick Power Off
Enable the projector to turn off quickly.
DC 12V Trigger
Enable or disable to trigger external devices such as an electric screen.
Option
Password
Set or delete the password. When the password function is added, image projection will
require to input the preset password when turning on the projector.
Blank Screen
Blank the screen temporarily, and select the screen color when this function is active.
OSD Setting
Allow you to enter the OSD Setting menu.
„
„
Menu Position: Choose the menu location on the display screen.
OSD Timeout: Duration of OSD menu display countly starts (at idle state by
second).
„
OSD Transparency: Select to change the transparency level of the OSD
background.
Closed Caption
Enable or disable closed captions by selecting CC1 (closed caption1, the most common
channel), CC2, CC3, CC4, T1, T2 or OFF.
Others
Allow you to enter the Others menu.
„
„
„
Message: Enable or disable the message box at the right bottom of the screen.
Zoom: Zoom in and out the images.
DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio
by darkening the black scenes. Disable DCR will resume to normal contrast
performance. DCR will impact lamp life and system noise performance.
Test Pattern: Display embedded test pattern.
„
Display Type
Allow user to select PIP (Picture in Picture) screen, POP (Picture on Picture) screen or
disable PIP/POP function.
Swap
ViewSonic Pro8400
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Allow user to swap input source in PIP or POP image.
Function
Allow user to define a short cut key on the remote control, and the function item is selected
in OSD menu.
Network
Wired LAN
Allow you to configure the wired LAN settings.
„
„
Status: Display the projector’s status.
DHCP: Abbreviation for Dynamic Host Configuration Protocol. This protocol
automatically assigns IP Address to networked devices.
„
When the “DHCP” sets to “Yes”, it takes some time to obtain IP address from
DHCP server.
„
When the "DHCP" sets to "No", that means user will set IP address by
manually.
„
IP Address: Numerical address to identify networked computers. This function
can only be used when DHCP is set to No.
„
The IP Address is the number that identifies this projector on the network.
You cannot have two devices with the same IP Address on the same
network.
„
The IP Address “0.0.0.0” is prohibited.
„
„
Subnet Mask: A numeric value to define the number of bits used for a network
address of a divided network (or subnet) in an IP Address. This function can only
be used when DHCP is set to No.
„
The Subnet Mask “0.0.0.0” is prohibited.
Default Gateway: A server (or router) to communicate across networks (subnets)
that are divided by Subnet Mask. This function can only be used when DHCP is
set to No.
„
„
DNS: Setup DNS server address when DHCP is disable.
Apply: Save and execute the wired LAN settings.
Wirless LAN
Allow you to configure the wireless LAN settings.
„
„
„
„
Status: Display the projector’s status.
SSID: Display the projector’s SSID information.
SSID Display: Select if you want to display the projector’s SSID.
Connection Mode: Methods for connecting to wireless networks with Wi-Fi
enabled devices.
„
AP: The projector is cabled to the wired network to allow other wireless
clients access to. The projector also supports a network control or web
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
33
server.
„
Infrastructure: A wireless networking bridges (joins) a wireless network to a
wired Ethernet network.
„
„
DHCP: Abbreviation for Dynamic Host Configuration Protocol. This protocol
automatically assigns IP Address to networked devices.
„
When the “DHCP” sets to “Yes”, it takes some time to obtain IP address from
DHCP server.
„
When the "DHCP" sets to "No", that means user will set IP address by
manually.
IP Address: Numerical address to identify networked computers. This function
can only be used when DHCP is set to No.
„
The IP Address is the number that identifies this projector on the network.
You cannot have two devices with the same IP Address on the same
network.
„
The IP Address “0.0.0.0” is prohibited.
„
„
Subnet Mask: A numeric value to define the number of bits used for a network
address of a divided network (or subnet) in an IP Address. This function can only
be used when DHCP is set to No.
„
The Subnet Mask “0.0.0.0” is prohibited.
Apply: Save and execute the wireless LAN settings.
Information
Input Source
Display the current input source.
Resolution
Display current input source resolution.
H. Frequency
Display current image horizontal frequency.
V. Frequency
Display current image vertical frequency.
MAC Address
Abbreviation for Media Access Control Address. MAC Address is a unique ID number
assigned to each network adapter.
Filter Hours
Display the filter’s elapsed operating time (in hours).
„
When Filter Mode is turned on, the Filter Hours also turns on automatically.
Filter Hours Reset
Reset the filter Hour to 0 hours.
Equivalent Lamp Hours
ViewSonic Pro8400
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Display the lamp’s elapsed operating time (in hours).
Equivalent Lamp Hours Reset
Reset the lamp Hour to 0 hours.
Factory Default
Restore settings to factory default.
Language
Select the language used by the on-screen menu.
ViewSonic Pro8400
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when
they are properly connected to the same local area network.
Wired connection
Internet
IP Router
If you are in a DHCP environment:
1.
2.
3.
Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the
projector and the other end to the RJ45 port on your Ethernet or router.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the NetWork menu is highlighted.
Highlight Wired LAN and press ENTER on the projector or Enter on the remote
control.
4.
5.
6.
Make sure the Status is Connect.
Press
Press
to highlight DHCP and press
to highlight Apply and press ENTER on the projector or Enter on the
/
to select On.
remote control.
7.
Please wait for around 15 - 20 seconds, and then re-enter the Wired LAN page.
The IP Address Subnet Mask, Default Gateway, and DNS settings will be
,
displayed. Note down the IP address displayed in the IP Address row.
Important
„ If the Projector IP Address still does not appear, contact your network
administrator.
„ If the RJ45 cables are not properly connected, the IP Address, Subnet Mask,
Default Gateway, and DNS settings will display 0.0.0.0. Make sure the
cables are properly connected and perform the procedures above again.
„ If you wish to connect to the projector in its standby mode, be sure you have
selected RJ45 and obtained the IP Address, Subnet Mask, Default Gateway,
and DNS information when the projector is on.
If you are in a non-DHCP environment:
1.
2.
3.
Repeat steps 1-4 above.
Press to highlight DHCP and press
Contact your ITS administrator for information on the IP Address, Subnet Mask,
Default Gateway, and DNS settings.
/
to select Off.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
36
4.
Press
or Enter on the remote control.
Press to move the cursor and the enter the value.
To save the settings, press ENTER on the projector or Enter on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
or Menu on the remote control.
to select the item you want to modify and press ENTER on the projector
5.
6.
/
7.
8.
Press
to highlight Apply and press ENTER on the projector or Enter on the
remote control.
Important
„ If the RJ45 cables are not properly connected, the IP Address, Subnet Mask,
Default Gateway, and DNS settings will display 0.0.0.0. Make sure the
cables are properly connected and perform the procedures above again.
„ If you wish to connect to the projector in its standby mode, be sure you have
selected RJ45 and obtained the IP Address, Subnet Mask, Default Gateway,
and DNS information when the projector is on.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Wireless connection
ViewSonic
wireless dongle
To connect to the projector wirelessly, you have to plug a ViewSonic wireless dongle
(optional) to the USB Type A connector on the projector, and then only a few OSD
configuration steps are required.
1.
2.
Make sure the projector is turned on.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the NetWork menu is highlighted.
3.
Highlight Wireless LAN and press ENTER on the projector or Enter on the
remote control.
4.
5.
6.
Make sure the Status is Connect
Make sure the SSID information is displayed.
Press to highlight Connection Mode and press
.
/
to select AP or
Infrastructure. In AP mode, you need to use your computer’s wireless
connection utility to search the projector’s SSID and connect to it. Then you can
search the projector with pwPresenter. To use Infrastructure mode, you should
connect both your computer and projector to the same AP router and make
connections with the IP address.
Important
„ If you need more information about AP and Infrastructure modes, please
refer to user documentations for Wireless Routers which are usually
available on 3C stores.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in
standby mode, you can use any computer that is on the same local area network to
control the projector.
Important
„ If you are using Microsoft Internet Explorer, make sure it is version 7.0 or
higher.
„ The screenshots in this manual are for reference only, and may differ from
the actual design.
1.
2.
Enter the address of the projector in the address bar of your browser and press
Enter.
The main page of the ViewSonic webpage control system appears.
7
3
4
5
8
6
3.
4.
To change the language for the web pages, click the down arrow to reveal a drop
down list and select a desired language.
pwPresenter” on page 45 for details.
5.
6.
To achieve best performance, download the install mirror display driver.
To download USB LAN driver, click Download.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
39
7.
To have access to the Admin page, you need to enter a password. The default
password is “0000”.
„
„
„
System Status: Displays the system information.
General Setup: Allows you to change the password for the Admin page.
Picture Setup/Image Setup: Provides some OSD menu items for adjusting
the projected pictures.
„
Alert Setup/SMTP Mail Setup: Allows you to setup the mail server and send
system error messages to your ITS administrator.
Network Setup: Provides wired and wireless network settings.
Presenter Setup: Allows you to change Admin and User passwords for web
control.
„
„
„
„
Reset to Default: Allows you to restore the device to the factory default
settings.
Reboot System: Allows you to reboot the device immediately.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
40
8.
The Crestron (eControl) page displays the Crestron eControl user interface. The
eControl page provides a variety of virtual keys to control the projector or adjust
the projected pictures.
i
i
ii
You can press
to reveal
more buttons.
W
/
X
i
iii
i.
These buttons function the same as the ones on the OSD menus or remote
control.
ii.
To switch between input signals, click on your desired signal.
iii. To change the language for the Crestron page, click the down arrow to
reveal a drop down list and select a desired language.
Important
„ The Menu button can also be used to go back to previous OSD menus, exit
and save menu settings.
„ The source list varies according to the connectors available on the projector.
„ When you use the projector control panel or remote control to change the
OSD menu settings, it may take a while for the web browser to synchronize
these changes with the projector.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
41
The tools page allows you to manage the projector, configure the LAN control settings
and secure access of remote network operation on this projector.
iv
v
vi
viii
vii
ix
x
iv. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
v.
Click the down arrow to reveal a drop down list and select a default
language.
vi. You can name the projector, keep track of its location and the person in
charge of it.
vii. You can adjust the LAN Control Settings.
viii. Once set, access to the remote network operation on this projector has
been password-protected.
ix. Once set, access to the tools page has been password-protected.
Important
„ To prevent errors, only input the English alphabet and digits on the tools
page.
„ After making the adjustments, press the Send button and the data will be
saved for the projector.
x.
Press Exit to go back to the remote network operation page.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Please pay attention to the limitation of input length (including space and other
punctuation keys) in the list blow:
Maximum Number of
Characters
Category Item
Input Length
IP Address
IP ID
Crestron Control
Projector
15
2
Port
5
Projector Name
Location
10
9
Assigned To
DHCP (Enabled)
IP Address
Subnet Mask
Default Gateway
DNS Server
Enabled
9
Network Configuration
(N/A)
15
15
15
15
(N/A)
20
2
User Password
New Password
Confirm
Admin Password
Enabled
(N/A)
20
20
New Password
Confirm
ViewSonic Pro8400
43
Download from Www.Somanuals.com. All Manuals Search And Download.
The info page displays the information and status of this projector.
Press Exit to go
back to the
remote network
operation page.
After pressing the button “Contact IT Help”, the HELP DESK window will appear in the
upper right corner of the screen. You will be able to deliver messages to RoomView
software administrators/users who connect to the same local area network.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
44
Displaying images through pwPresenter
Downloading and installing pwPresenter
The pwPresenter is an application running on the host PC. It helps connect your
computer to an available network projector and transfer the desktop content to the
network projector via local network connection.
1.
2.
3.
Download pwPresenter.
When the download is complete, install the software to your computer by clicking
the exe file. Follow the on-screen instructions to complete the installation.
Launch pwPresenter.
4.
Using pwPresenter
1
7
6
2
3
&
5
4
1.
The Search page allows you to search and connect to a projector.
i
iii
ii
i.
To connect to a projector, select Directly then type the projector IP address
and click Connect.
ii.
To search for projectors, simply click Search to list all the projectors on the
same local area network. Click the desired projectors in the Search result
list, and click Connect directly. You can also type a desired projector name
and click Search.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
45
2.
3.
The Capture screen allows you to start or pause capture screen.
You can choose a capture mode from here.
i
ii
iii
i.
To display a full screen, click FullScreen.
ii.
To display a partial screen, click FixedSize. A square appears on your
screen. You can place it where you want to project.
iii. If you wish to change the square, click Alterable.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
46
4.
The Basic Setting page allows you to configure pwPresenter.
i
ii
iii
iv
v
i.
To change the pwPresenter interface language, click the down arrow to
reveal a drop-down list and select a desired language. Click Apply.
Users can change the size parameters of the frame in FixedSize capture
mode by modifying width and height on this page and click Apply to make
changes take effect.
ii.
iii. User can use the mirror driver for presenter capture image, if the system
has installed the mirror driver.
iv. To allow notification messages to appear, click Yes. Click Apply.
v.
The Software Information is available on this page.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
47
5.
The Advanced Setting page allows you to configure pwPresenter.
i
ii
iii
i.
To adjust the image quality, click the down arrow to reveal a drop-down list
and select a desired quality level. Click Apply.
ii.
To adjust the capture rate, move the slide bar. The network bandwidth may
also affect the performance.
iii. Network port setting for fixed or manual type.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
48
6.
Network Display Management displays the Device Management and pwPresenter
Management information.
Device Management allows you to change device settings
.
i
iii
ii
iv
v
i.
ii.
Click to change display port allows you to select display location of screen.
Change password allows you to change password for the user type.
iii. Disconnect allows you to disconnect the projector from network.
iv. Access device via webpage allows you to access ViewSonic webpage con-
trol system.
v.
View device status displays device setting information and allows you to
enter conference control mode.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
49
pwPresenter Management allows you to select which computer to be connected
and transfer the desktop content to the network projector.
7.
Disconnect allows you to disconnect from the projector(s) by clicking the
Disconnect icon.
Important
„ Be sure to turn off other virtual network control programs before using
pwPresenter.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Displaying pictures with a USB storage device
The built-in the ImageViewer application can display packaged images on a USB
storage device (e.g. USB flash drive, and USB disk), a digital camera, or other device.
You can connect a USB storage device to your projector.
1.
Take a USB cable and connect the larger end to the USB A socket on the
projector, and smaller end to the USB port of the device. If you are using a USB
flash drive, connect it directly to the USB A socket.
2.
3.
The projector automatically display the thumbnails. Or your can manually select
USB Reader from the source selection bar.
The ImageView main screen is displayed and ready to use. The main screen is
displayed in Thumbnail Display Mode which shows the following four parts:
i
ii
iii
iv
i.
ii.
Current path, USB storage device name and page number
File and folder name display (i18N, multi-language)
iii. Thumbnail images (120 x 120 pixels images)
iv. Operation User Interface
4.
Use the four directional buttons or page up/down button to move between pages/
folders. To Press and hold Menu and then press Enter to display the operation
user interface. Use
. To confirm the selection press Enter. The following buttons are supported
in the user interface.
/
to select the desired item and adjust the settings with
/
„
„
Next: Display next page.
Previous: Display previous page.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
51
„
„
Thumbnail/Slide show/Display: Display thumbnails, start the slide show or
display the selected image.
Name Order/Extend Order/Size Order/Time Order: Select the order setting
by file/folder name, extended file name, image size or time.
EXIF ON/EXIF OFF: Display the Exif information of the image or not.
File Name On/File Name Off: Display the file name or not.
„
„
The projector supports the following image formats:
„
„
„
„
„
JPEG (JPG)
Bitmap (BMP)
Portable Network Graphic (PNG)
Graphics Interchange Format (GIF)
Tagged Image File Format (TIFF)
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Maintenance
The projector needs proper maintenance. You should keep the lens clean as dust, dirt
or spots will project on the screen and diminish image quality. If any other parts need
replacing, contact your dealer or qualified service personnel. When cleaning any part
of the projector, always switch off and unplug the projector first.
Warning
Never open any of the covers on the projector. Dangerous electrical voltages
inside the projector can cause severe injury. Do not attempt to service this
product yourself. Refer all servicing to qualified service personnel.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Projector Housing
Gently wipe with a soft cloth. If dirt and stains are not easily removed, use a soft cloth
damped with water, or water and neutral detergent, and wipe dry with a soft, dry cloth.
Cleaning the Filter Cover
The filter cover, which is located at the side of the projector, should be cleaned after
every 100 hours of use. If it is not cleaned periodically, it can become clogged with
dust and prevent the projector from being ventilated properly. This can cause over
heating and damage the projector.
To clean the filter cover:
1.
2.
3.
Switch the projector off and unplug the AC
power cord from the wall socket.
Remove the filter cover as the illustration
shown.
Clean the filter cover.
„
To clean the filter cover, you are
advised to use a small vacuum
cleaner designed for computers and
other office equipment.
„
If the filter cover is torn, replace it.
Replace the filter cover.
4.
5.
6.
Attach the filter cover.
Plug the power back into the projector.
„
Turn off the projector and remove the AC power cord from the power outlet
before beginning maintenance work.
„
„
Make sure the lens is cool before cleaning.
Do not use detergents or chemicals other than those noted above. Do not use
benzene or thinners.
„
„
Do not use chemical sprays.
Use a soft cloth or lens paper only.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Replacing the Lamp
As the projector operates over time, the brightness of the projector lamp gradually
decreases and the lamp becomes more susceptible to breakage. We recommend
replacing the lamp if a warning message is displayed. Do not attempt to replace the
lamp yourself. Contact the qualified service personnel for replacement.
„
The lamp is extremely hot right after turning off the projector. If you touch the
lamp, you may scald your finger. When you replace the lamp, wait for at least
45 minutes for the lamp to cool down.
„
„
Do not touch the lamp glass at any time. The lamp may explode due to
improper handling, including the touching of the lamp glass.
Lamp lifetime may differ from lamp to lamp and according to the environment
of use. There is no guarantee of the same lifetime for each lamp. Some lamps
may fail or terminate their lifetime in a shorter period of time than other similar
lamps.
„
A lamp may explode as a result of vibration, shock or degradation as a result of
hours of use as its lifetime draws to an end. Risk of explosion may differ
according to the environment or conditions in which the projector and lamp are
being used.
„
„
Wear protective gloves and eyeglasses when fixing or detaching the lamp.
Faster on-off-cycles will damage the lamp and reduce lamp life. Wait at least
for 5 minutes to turn off the projector after powering on.
Do not operate the lamp in proximity to paper, cloth, or other combustible
material nor cover it with such materials.
Do not operate the lamp in an atmosphere containing an inflammable
substance, such as thinner.
Thoroughly ventilate the area or the room when operating the lamp in an
oxygen atmosphere (in the air). If ozone is inhaled, it could cause headaches,
nausea, dizziness, and other symptoms.
„
„
„
„
The inorganic mercury is involved in the lamp. If the lamp bursts, the mercury
inside the lamp will be exposed. Leave the area immediately if the lamp
shatters while being operated and ventilate the area for at least 30 minutes in
order to avoid the inhalation of mercury fumes. Otherwise it could be harmful to
user’s health.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
54
1.
2.
3.
4.
5.
Turn off the projector.
If the projector is installed in a ceiling mount, remove it
Unplug the power cord.
Loosen the screw in the side of the lamp cover and remove the cover.
Remove the screws from the lamp module, raise the handle, and lift out the
module.
6.
7.
8.
Insert the new lamp module into the projector and tighten the screws.
Replace the lamp cover and tighten the screw.
Turn on the projector. If the lamp does not turn on after the warm-up period, try
reinstalling the lamp.
9.
Reset the lamp hour. Refer to the “Information” menu.
„
„
Dispose the used lamp according to local regulations.
Ensure that screws are tightened properly. Screws not tightened fully may
result in injury or accidents.
„
Since the lamp is made of glass, do not drop the unit and do not scratch the
glass.
„
„
Do not reuse the old lamp. This could cause the lamp to explode.
Be sure to turn off the projector and unplug the AC power cord before
replacing the lamp.
„
Do not use the projector with the lamp cover removed.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Specifications
Display system
Resolution
Zoom
Single 0.65" DLP panel
1080p (1920 × 1080 pixels)
1.5X
F/No.
2.41 - 2.97
Focal length
Screen size
Lamp
20.72 - 31mm
30” - 300”
280W
Input terminal
D-Sub 15-pin x 2, S-Video x 1, Video x 1, Audio signal input (3.5
mm stereo mini jack) x 2, HDMI x 2, Component RCA jack x 1,
RCA audio jack (L/R) x 1, 3.5 mm Mic input x1, USB A type x1
(supports firmware update, USB flash drive display and wireless
dongle for USB display), USB mini-B type x1 (supports USB
display)
Output terminal
D-Sub 15 pin x 1, Audio signal output (3.5 mm stereo mini jack) x
1
Control terminal
Speaker
RS-232 x 1, 12-Vdc trigger output x 1, RJ45 x 1
10 watt x 2
Video compatibility
NTSC, NTSC 4.43
PAL, PAL-N, PAL M
SECAM, HDTV (480i/p, 576p, 720p, 1080i/p), Composite video
Scanning frequency
Horizontal frequency
Vertical frequency
Environment
31 - 100 KHz
50 - 120 Hz
Operating:
Temperature: 0°C to 40°C
Humidity: 10%-80%
Storage:
Temperature: -20°C to 60°C
Humidity: 30%-85%
AC 100-240 V, 50 - 60 Hz, 3.8A
390 W
Power requirement
Power consumption
Dimension (W x D x H)
Weight
334.6 x 264.5 x 109.5 mm
3.63 kg (8 lb)
Note: Design and Specifications are subject to change without prior notice.
ViewSonic Pro8400
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix
LED Indicator Messages
LED type
Color
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Status
Solid
Flash
Flash
Solid
Off
Meaning
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Lamp life end
Standby mode when green mode is
turned on.
Off
Flash
Off
Standby mode when green mode is
turned off.
Off
Solid
Off
Powering up
Off
Solid
Off
Normal operation
Off
Flash
Off
Powering down
(The projector needs to cool for 35
seconds after the power is turned off.)
Off
Solid
Solid
Flash
Solid
Solid
Off
The projector system has some
problems with its fans, so the projector
cannot start up.
The lamp has reached its end of life and
must be changed soon. The lamp will
continue to opearate until it failes.
Change the lamp. If the lamp is off, then
the ballast will become malfuction.
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Power LED
Lamp LED
Temp LED
Blue
Red
Red
Blue
Red
Red
Blue
Red
Red
Solid
Flash
Off
Temperature is too high. The lamp will
turn off. The fan motor is cooling the
lamp.
Off
The lamp ignition failied. If temperature
is too high, the fans will cool the lamp.
Solid
Solid
Flash
Solid
Off
The projector needs to cool for 90
seconds after the power is turned off. If
you try to re-start the projector, it will
shut down again.
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Compatibility Modes
Computer:
Compatibility
VGA
Resolution
H-Sync [KHz]
24.69
31.5
37.9
37.5
43.3
30.99
35.2
37.9
48.1
46.9
53.7
39.63
48.4
56.5
60
V-Sync [Hz]
50
640 x 480
60
72
75
85
SVGA
800 x 600
50
56
60
72
75
85
XGA
1024 x 768
50
60
70
75
SXGA
1280 x 1024
64
60
80
75
UXGA
1600 x 1200
640 x 480
47.7
35
60
Mac 13
Mac 16
Mac 19
1080i30
1080i25
480p
67
832 x 624
49.72
60.24
33.75
28.13
31.47
31.25
45
75
1024 x 768
1920 x 1080
1920 x 1080
720 x 480
75
60
50
59.94
50
576p
720 x 576
720p60
720p50
1080p60
1080p50
1280 x 720
1280 x 720
1920 x 1080
1920 x 1080
60
37.5
67.5
56.25
50
60
50
ViewSonic Pro8400
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Video:
Compatibility
1080p
1080p
1080i
1080i
720p
Resolution
1920 x 1080
1920 x 1080
1920 x 1080
1920 x 1080
1280 x 720
1280 x 720
720 x 576
H-Sync [KHz]
67.5
V-Sync [Hz]
60
50
60
50
60
50
50
50
60
60
56.3
33.8
28.1
45
720p
37.5
576p
31.3
576i
720 x 576
15.6
480p
720 x 480
31.5
480i
720 x 480
15.8
ViewSonic Pro8400
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Refer to the symptoms and measures listed below before sending the projector for
repairs. If the problem persists, contact your local reseller or service center. Please
refer to "LED Indicator Messages" as well.
Start-up problems
If no lights turn on:
„
Be sure that the power cord is securely connected to the projector and the other end
is plugged into an outlet with power.
„
„
Press the power button again.
Unplug the power cord and wait for a short while, then plug it in and press the power
button again.
Image problems
If the searching source is displayed:
„
„
„
Press SOURCE on the projector to select an active input source.
Be sure the external source is turned on and connected.
For a computer connection, ensure your notebook computer’s external video port is
turned on. Refer to the computer manual.
If the image is out of focus:
„
„
Be sure the lens cover is removed.
While displaying the on-screen menu, adjust the focus ring. (The image size should
not change; if it does, you are adjusting the zoom, not the focus.)
Check the projection lens to see if it needs cleaning.
„
If the image is flickering or unstable for a computer connection:
„
Press MENU on the projector or Menu on the remote control, go to Video/Audio
and adjust Frequency or Tracking.
Remote control problems
If the remote control does not operate:
„
Be sure nothing is blocking the remote control receiver on the front of the
projector. Use the remote control within the effective range.
Aim the remote control at the screen or at the front or back of the projector.
Move the remote control so it is more directly in front of or behind the projector and
not as far to the side.
„
„
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
61
RS-232 Command and Configuration
POWER ON / POWER OFF
POWER ON
POWER OFF
SOURCE SELECT
Computer 1
Computer 2
COMPONENT
COMPOSITE
S-VIDEO
BE,EF,10,05,00,C6,FF,11,11,01,00,01,00
BE,EF,02,06,00,6D,D2,34,00,00,00,00,00
BE,EF,02,06,00,BC,D3,35,00,00,00,00,00
BE,EF,02,06,00,8F,D3,36,00,00,00,00,00
BE,EF,02,06,00,5E,D2,37,00,00,00,00,00
BE,EF,02,06,00,A1,D2,38,00,00,00,00,00
BE,EF,02,06,00,70,D3,39,00,00,00,00,00
BE,EF,02,06,00,43,D3,3A,00,00,00,00,0
BE,EF,02,06,00,92,D2,3B,00,00,00,00,00
HDMI 1
HDMI 2
QUICK KEY
MENU
BE,EF,02,06,00,C8,D7,01,00,00,00,00,00
BE,EF,02,06,00,FB,D7,02,00,00,00,00,0
BE,EF,02,06,00,2A,D6,03,00,00,00,00,00
BE,EF,02,06,00,9D,D7,04,00,00,00,00,00
BE,EF,02,06,00,4C,D6,05,00,00,00,00,00
BE,EF,02,06,00,E6,D6,0F,00,00,00,00,00
BE,EF,02,06,00,F2,D5,1B,00,00,00,00,00
BE,EF,02,06,00,C7,D2,3E,00,00,00,00,00
BE,EF,02,06,00,16,D3,3F,00,00,00,00,0
BE,EF,02,06,00,D9,D8,40,00,00,00,00,00
BE,EF,02,06,00,08,D9,41,00,00,00,00,00
BE,EF,02,06,00,7F,D6,06,00,00,00,00,00
UP
DOWN
LEFT
RIGHT
ENTER
RESYNC
ASPECT
MUTE
FREEZE
BLANK
SOURCE
OTHER FUNCTION
DCR ON
BE,EF,02,06,00,EA,D8,43,00,00,00,00,00
BE,EF,02,06,00,5D,D9,44,00,00,00,00,00
BE,EF,02,06,00,8C,D8,45,00,00,00,00,0
BE,EF,02,06,00,BF,D8,46,00,00,00,00,00
BE,EF,02,06,00,6E,D9,47,00,00,00,00,00
BE,EF,02,06,00,91,D9,48,00,00,00,00,00
BE,EF,02,06,00,40,D8,49,00,00,00,00,00
BE,EF,02,06,00,73,D8,4A,00,00,00,00,00
BE,EF,02,06,00,A2,D9,4B,00,00,00,00,00
BE,EF,02,06,00,15,D8,4C,00,00,00,00,00
BE,EF,02,06,00,C4,D9,4D,00,00,00,00,00
BE,EF,02,06,00,F7,D9,4E,00,00,00,00,00
DCR OFF
ECO ON
ECO OFF
VOLUME INC
VOLUME DEC
KEYSTONE INC
KEYSTONE DEC
FACTORY RESET
LAMP HOURS RESET
FILTER HOURS RESET
Projector status
ViewSonic Pro8400
62
Download from Www.Somanuals.com. All Manuals Search And Download.
D-Sub 9 pin
Wire List
COLOR
Black
1
2
3
4
5
6
7
8
9
1 CD
RXD
TXD
DTR
GND
DSR
RTS
CTS
RI
C1
C2
1
1
2
Brown
Red
2
3
3
4
Orange
Yellow
Green
Blue
4
5
5
6
6
7
7
8
9
Purple
White
DW
8
9
SHELL
SHELL
ViewSonic Pro8400
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
T = Telephone
F = FAX
Country/Region
Website
Email
AUS= 1800 880 818
NZ= 0800 008 822
Australia/New Zealand
T (Toll-Free)= 1-866-463-4775
T (Toll)= 1-424-233-2533
F= 1-909-468-3757
Canada
Europe
Hong Kong
India
T= 852 3102 2900
T= 1800 11 9999
support/call-desk/
Ireland (Eire)
Korea
T= 080 333 2131
T= 0800-4441185
T= 1230-020-7975
T= 01800-9-157235
T= 001-8882328722
Latin America
(Argentina)
Latin America (Chile)
Latin America
(Columbia)
Latin America (Mexico)
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Latin America (Peru)
Macau
ap.viewsonic.com/me/
T= 0800-54565
T= 853 2870 0303
Contact your reseller
Middle East
T= 1-800-688-6688 (English)
T= 1-866-379-1304 (Spanish)
F= 1-909-468-3757
T= 65 6461 6044
South Africa
ap.viewsonic.com/za/
Contact your reseller
support/call-desk/
United Kingdom
T (Toll-Free)= 1-800-688-6688
T (Toll)= 1-424-233-2530
F= 1-909-468-3757
United States
ViewSonic Pro8400
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South America: Three (3) years
warranty for all parts excluding the lamp, three (3) years for labor, and one (1) year for the original lamp
from the date of the first consumer purchase; Europe except Poland: Three (3) years warranty for all parts
excluding the lamp, three (3) years for labor, and ninety (90) days for the original lamp from the date of
the first consumer purchase; Poland: Two (2) years warranty for all parts excluding the lamp, two (2) years
for labor, and ninety (90) days for the original lamp from the date of the first consumer purchase.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than four (4) hours average daily
usage, North and South America: One (1) year warranty for all parts excluding the lamp, one (1) year for
labor, and ninety (90) days for the original lamp from the date of the first consumer purchase; Europe:
One (1) year warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for
the original lamp from the date of the first consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic office for the
warranty information.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s
installed lamp only. All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a. Accident, abuse, misuse, neglect, fire, water, lightning, or other acts of nature, improper
maintenance, unauthorized product modification, or failure to follow instructions supplied
with the product.
b. Operation outside of product specifications.
c. Operation of the product for other than the normal intended use or not under normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power fluctuations or failure.
ViewSonic Pro8400
66
Download from Www.Somanuals.com. All Manuals Search And Download.
h. Use of supplies or parts not meeting ViewSonic’s specifications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
How to get service:
1. For information about receiving service under warranty, contact ViewSonic Customer Support
(please refer to “Customer Support” page). You will need to provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name,
(c) your address, (d) a description of the problem, and (e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service
center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill,
interference with business relationships, or other commercial loss, even if advised of the possibility
of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada,
contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is
subject to the terms and conditions of the Maintenance Guarantee Card.
com under Support/Warranty Information.
4.3: Projector Warranty
PRJ_LW01 Rev. 1h 06-25-07
ViewSonic Pro8400
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Mexico Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the
warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include
remanufactured or refurbished parts or components & accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of the first consumer purchase.
Lamp warranty subject to terms and conditions, verification and approval. Applies to manufacturer’s installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification,
unauthorized attempted repair, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power fluctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specifications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the
attached Customer Support page). You will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
Product Name: ________________________
Document Number: ____________________
Purchase Date: ________________________
Model Number: __________________________
Serial Number: ___________________________
Extended Warranty Purchase? _______________(Y/N)
If so, what date does warranty expire? _________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein including the
implied warranty of merchantability and fitness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of
the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
ViewSonic Pro8400
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Villahermosa:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: [email protected]
Puebla, Pue. (Matriz):
Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09
E-Mail: [email protected]
Veracruz, Ver.:
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: [email protected]
Chihuahua
Tel: 01-22-91-00-31-67
E-Mail: [email protected]
Cuernavaca
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: [email protected]
Distrito Federal:
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: [email protected]
Guadalajara, Jal.:
QPLUS, S.A. de C.V.
SERVICRECE, S.A. de C.V.
Av. Coyoacán 931
Av. Niños Héroes # 2281
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : [email protected]
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: 01(52)33-36-15-15-43
E-Mail: [email protected]
Monterrey:
Guerrero Acapulco
GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: 744-48-32627
Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: 8129-5103
E-Mail: [email protected]
Oaxaca, Oax.:
MERIDA:
ELECTROSER
CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: 01(52)95-15-15-22-22
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: (52) 999-925-1916
E-Mail: [email protected]
Fax: 01(52)95-15-13-67-00
E-Mail. [email protected]
FOR USA SUPPORT:
Tijuana:
STD
ViewSonic Corporation
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico
381 Brea Canyon Road, Walnut, CA. 91789 USA
Tel: 800-688-6688 (English); 866-323-8056 (Spanish);
Fax: 1-800-685-7276
4.3: ViewSonic Mexico Limited Warranty
PRJ_LW03 Rev. 1A 06-25-07
ViewSonic Pro8400
69
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|