PJD5126_PJD5226_PJD5226w_
PJD6223_PJD6253_PJD6353_
PJD6353s_PJD6383_PJD6383s_
PJD6553w_PJD6653w_
PJD6653ws_PJD6683w_
PJD6683ws
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
YLHZVRQLFꢀFRPꢁLQꢁ(QJOLVKꢂꢁRUꢁLQꢁVSHFL¿FꢁODQJXDJHVꢁXVLQJꢁWKHꢁ5HJLRQDOꢁVHOHFWLRQꢁER[ꢁLQꢁ
the upper right corner of our website. “Antes de operar su equipo lea cu idadosamente
las instrucciones en este manual”
Model No. VS14295/VS14551/VS14552/VS14191/VS14193
/ VS14555/VS14553/VS14195/VS14554/VS14550
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1.
Read these instructions.
2.
Keep these instructions.
ꢅꢁꢀꢀ +HHGꢀDOOꢀZDUQLQJVꢁ
ꢇꢁꢀꢀ )ROORZꢀDOOꢀLQVWUXFWLRQVꢁ
ꢌꢁꢀꢀ 'RꢀQRWꢀXVHꢀWKLVꢀXQLWꢀQHDUꢀZDWHUꢁ
ꢊꢁꢀꢀ ꢀ&OHDQꢀZLWKꢀDꢀVRIWꢐꢀGU\ꢀFORWKꢁ
ꢑꢁꢀꢀ ꢀ'RꢀQRWꢀEORFNꢀDQ\ꢀYHQWLODWLRQꢀRSHQLQJVꢁꢀ,QVWDOOꢀWKHꢀXQLWꢀLQꢀDFFRUGDQFHꢀZLWKꢀWKHꢀ
manufacturer’s instructions.
ꢉꢁꢀꢀ ꢀ'RꢀQRWꢀLQVWDOOꢀQHDUꢀDQ\ꢀKHDWꢀVRXUFHVꢀVXFKꢀDVꢀUDGLDWRUVꢐꢀKHDWꢀUHJLVWHUVꢐꢀVWRYHVꢐꢀRUꢀRWKHUꢀ
GHYLFHVꢀꢍLQFOXGLQJꢀDPSOL¿HUVꢎꢀWKDWꢀSURGXFHꢀKHDWꢁ
ꢋꢁꢀꢀ ꢀ'RꢀQRWꢀGHIHDWꢀWKHꢀVDIHW\ꢀSXUSRVHꢀRIꢀWKHꢀSRODUL]HGꢀRUꢀJURXQGLQJꢃW\SHꢀSOXJꢁꢀ$ꢀSRODUL]HGꢀ
SOXJꢀKDVꢀWZRꢀEODGHVꢀZLWKꢀRQHꢀZLGHUꢀWKDQꢀWKHꢀRWKHUꢁꢀ$ꢀJURXQGLQJꢀW\SHꢀSOXJꢀKDVꢀWZRꢀ
blades and a third grounding prong. The wide blade and the third prong are provided
IRUꢀ\RXUꢀVDIHW\ꢁꢀ,IꢀWKHꢀSURYLGHGꢀSOXJꢀGRHVꢀQRWꢀ¿WꢀLQWRꢀ\RXUꢀRXWOHWꢐꢀFRQVXOWꢀDQꢀHOHFWULFLDQꢀ
for replacement of the obsolete outlet.
ꢈꢄꢁꢀꢀ ꢀ3URWHFWꢀWKHꢀSRZHUꢀFRUGꢀIURPꢀEHLQJꢀZDONHGꢀRQꢀRUꢀSLQFKHGꢀSDUWLFXODUO\ꢀDWꢀSOXJVꢁꢀ
&RQYHQLHQFHꢀUHFHSWDFOHVꢀDQGꢀWKHꢀSRLQWꢀZKHUHꢀWKH\ꢀH[LWꢀIURPꢀWKHꢀXQLWꢁꢀ%HꢀVXUHꢀWKDWꢀWKHꢀ
power outlet is located near the unit so that it is easily accessible.
ꢈꢈꢁꢀꢀ ꢀ2QO\ꢀXVHꢀDWWDFKPHQWVꢂDFFHVVRULHVꢀVSHFL¿HGꢀE\ꢀWKHꢀPDQXIDFWXUHUꢁ
ꢈꢆꢁꢀꢀ ꢀ8VHꢀRQO\ꢀZLWKꢀWKHꢀFDUWꢐꢀVWDQGꢐꢀWULSRGꢐꢀEUDFNHWꢐꢀRUꢀWDEOHꢀVSHFL¿HGꢀE\ꢀWKHꢀ
manufacturer, or sold with the unit. When a cart is used, use caution when
PRYLQJꢀWKHꢀFDUWꢂXQLWꢀFRPELQDWLRQꢀWRꢀDYRLGꢀLQMXU\ꢀIURPꢀWLSSLQJꢀRYHUꢁ
ꢈꢅꢁꢀꢀ ꢀ8QSOXJꢀWKLVꢀXQLWꢀZKHQꢀXQXVHGꢀIRUꢀORQJꢀSHULRGVꢀRIꢀWLPHꢁ
ꢈꢇꢁꢀꢀ ꢀ5HIHUꢀDOOꢀVHUYLFLQJꢀWRꢀTXDOL¿HGꢀVHUYLFHꢀSHUVRQQHOꢁꢀ6HUYLFLQJꢀLVꢀUHTXLUHGꢀZKHQꢀWKHꢀXQLWꢀ
KDVꢀEHHQꢀGDPDJHGꢀLQꢀDQ\ꢀZD\ꢐꢀVXFKꢀDVꢒꢀLIꢀWKHꢀSRZHUꢃVXSSO\ꢀFRUGꢀRUꢀSOXJꢀLVꢀGDPDJHGꢐꢀ
LIꢀOLTXLGꢀLVꢀVSLOOHGꢀRQWRꢀRUꢀREMHFWVꢀIDOOꢀLQWRꢀWKHꢀXQLWꢐꢀLIꢀWKHꢀXQLWꢀLVꢀH[SRVHGꢀWRꢀUDLQꢀRUꢀ
moisture, or if the unit does not operate normally or has been dropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
Declaration of RoHS Compliance
7KLVꢀSURGXFWꢀKDVꢀEHHQꢀGHVLJQHGꢀDQGꢀPDQXIDFWXUHGꢀLQꢀFRPSOLDQFHꢀZLWKꢀ'LUHFWLYHꢀꢆꢄꢄꢆꢂꢋꢌꢂ(&ꢀRIꢀWKHꢀ
(XURSHDQꢀ3DUOLDPHQWꢀDQGꢀWKHꢀ&RXQFLOꢀRQꢀUHVWULFWLRQꢀRIꢀWKHꢀXVHꢀRIꢀFHUWDLQꢀKD]DUGRXVꢀVXEVWDQFHVꢀLQꢀ
HOHFWULFDOꢀDQGꢀHOHFWURQLFꢀHTXLSPHQWꢀꢍ5R+6ꢀ'LUHFWLYHꢎꢀDQGꢀLVꢀGHHPHGꢀWRꢀFRPSO\ꢀZLWKꢀWKHꢀPD[LPXPꢀ
FRQFHQWUDWLRQꢀYDOXHVꢀLVVXHGꢀE\ꢀWKHꢀ(XURSHDQꢀ7HFKQLFDOꢀ$GDSWDWLRQꢀ&RPPLWWHHꢀꢍ7$&ꢎꢀDVꢀVKRZQꢀEHORZꢒꢀ
Proposed Maximum
Substance
Actual Concentration
Concentration
/HDGꢀꢍ3Eꢎ
ꢄꢁꢈꢏ
ꢄꢁꢈꢏ
ꢄꢁꢄꢈꢏ
ꢄꢁꢈꢏ
ꢄꢁꢈꢏ
ꢄꢁꢈꢏ
ꢓꢀꢄꢁꢈꢏ
ꢓꢀꢄꢁꢈꢏ
ꢓꢀꢄꢁꢄꢈꢏ
ꢓꢀꢄꢁꢈꢏ
ꢓꢀꢄꢁꢈꢏ
ꢓꢀꢄꢁꢈꢏ
0HUFXU\ꢀꢍ+Jꢎ
Cadmium (Cd)
ꢊꢔ
+H[DYDOHQWꢀ&KURPLXPꢀꢍ&U
)
Polybrominated biphenyls (PBB)
3RO\EURPLQDWHGꢀGLSKHQ\OꢀHWKHUVꢀꢍ3%'(ꢎ
&HUWDLQꢀFRPSRQHQWVꢀRIꢀSURGXFWVꢀDVꢀVWDWHGꢀDERYHꢀDUHꢀH[HPSWHGꢀXQGHUꢀWKHꢀ$QQH[ꢀRIꢀWKHꢀ5R+6ꢀ'LUHFWLYHVꢀ
as noted below:
([DPSOHVꢀRIꢀH[HPSWHGꢀFRPSRQHQWVꢀDUHꢒ
ꢈꢁꢀꢀ0HUFXU\ꢀLQꢀFRPSDFWꢀÀXRUHVFHQWꢀODPSVꢀQRWꢀH[FHHGLQJꢀꢌꢀPJꢀSHUꢀODPSꢀDQGꢀLQꢀRWKHUꢀODPSVꢀQRWꢀ
VSHFL¿FDOO\ꢀPHQWLRQHGꢀLQꢀWKHꢀ$QQH[ꢀRIꢀ5R+6ꢀ'LUHFWLYHꢁ
ꢆꢁꢀꢀ/HDGꢀLQꢀJODVVꢀRIꢀFDWKRGHꢀUD\ꢀWXEHVꢐꢀHOHFWURQLFꢀFRPSRQHQWVꢐꢀÀXRUHVFHQWꢀWXEHVꢐꢀDQGꢀHOHFWURQLFꢀFHUDPLFꢀ
SDUWVꢀꢍHꢁJꢁꢀSLH]RHOHFWURQLFꢀGHYLFHVꢎꢁ
ꢅꢁꢀꢀ/HDGꢀLQꢀKLJKꢀWHPSHUDWXUHꢀW\SHꢀVROGHUVꢀꢍLꢁHꢁꢀOHDGꢃEDVHGꢀDOOR\VꢀFRQWDLQLQJꢀꢉꢌꢏꢀE\ꢀZHLJKWꢀRUꢀPRUHꢀOHDGꢎꢁ
ꢇꢁꢀꢀ/HDGꢀDVꢀDQꢀDOORWWLQJꢀHOHPHQWꢀLQꢀVWHHOꢀFRQWDLQLQJꢀXSꢀWRꢀꢄꢁꢅꢌꢏꢀOHDGꢀE\ꢀZHLJKWꢐꢀDOXPLQLXPꢀFRQWDLQLQJꢀXSꢀ
WRꢀꢄꢁꢇꢏꢀOHDGꢀE\ꢀZHLJKWꢀDQGꢀDVꢀDꢀFRRSHUꢀDOOR\ꢀFRQWDLQLQJꢀXSꢀWRꢀꢇꢏꢀOHDGꢀE\ꢀZHLJKWꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Copyright Information
Copyright© ViewSonic® Corporation, 2012. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are
trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material, or
the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change
product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available,
®
ROM also provides an opportunity for you to print the registration form, which you may mail or fax to
ViewSonic.
For Your Records
Product Name:
PJD5126_PJD5226_PJD5226w_PJD6223_PJD6253_PJD6353_PJD6353s_
PJD6383_PJD6383s_PJD6553w_PJD6653w_PJD6653ws_PJD6683w_PJD6683ws
ViewSonic DLP Projector
Model Number:
VS14295/VS14551/VS14552/VS14191/VS14193/ VS14555/VS14553/VS14195/
VS14554/VS14550
Document Number:
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws_UG_ENG
Rev. 1C 04-25-12
Serial Number:
Purchase Date:
__________________________________________________________________
__________________________________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the environment. Please
use care and dispose of in accordance with local, state or federal laws.
ViewSonic respects the environment and is committed to working and living green. Thank you for being
part of Smarter, Greener Computing. Please visit ViewSonic website to learn more.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
Table of contents
Controlling the projector through
Important safety
a LAN environment........................... 39
instructions .......................2
Using the projector in standby mode. 45
Shutting down the projector .............. 45
Menu operation.................................. 46
Introduction......................4
Projector features ................................. 4
Shipping contents................................. 5
Projector exterior view......................... 6
Controls and functions ......................... 7
Maintenance ...................56
Care of the projector.......................... 56
Lamp information.............................. 57
Positioning your
Troubleshooting .............63
Specifications..................64
Projector specifications...................... 64
Dimensions........................................ 66
Ceiling mount installation ................. 66
Timing chart ...................................... 67
projector..........................12
Choosing a location............................ 12
Projection dimensions........................ 13
Connection......................17
Connecting a computer or monitor .... 18
Connecting Video source devices...... 19
Copyright information...69
Appendix.........................70
IR control table.................................. 70
RJ45 response table ........................... 72
RS232 command table....................... 72
Operation........................22
Starting up the projector..................... 22
Using the menus................................. 23
Utilizing the password function......... 24
Switching input signal........................ 27
Adjusting the projected image ........... 28
Magnifying and searching for details. 29
Selecting the aspect ratio ................... 30
Optimizing the image......................... 32
Setting the presentation timer ............ 36
Hiding the image................................ 37
Locking control keys.......................... 37
Freezing the image............................. 37
Operating in a high altitude
environment ....................................... 37
Creating your own startup screen....... 38
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.
Please read this manual before you operate your projector. Save it for future
reference.
Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
Refer servicing to qualified service personnel.
Always open the lens shutter or remove the lens cap when the projector lamp is
on.
In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of 10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
2.
3.
4.
5.
6.
7.
8.
9.
The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
Download from Www.Somanuals.com. All Manuals Search And Download.
2
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommends that you also purchase a separate Kensington lock compatible security
cable and attach it securely to both the Kensington lock slot on the projector and the base of
the ceiling mount bracket. This will perform the secondary role of restraining the projector
should its attachment to the mounting bracket become loose.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
•
Dynamic PC and Dynamic Movie function adjusting the power consumption of the
lamp according to the brightness of the image being projected
DynamicEco Timer function decreasing the power consumption of the lamp by up to
70% when no input signal can be detected for a set period of time.
Presentation timer for better control of time during presentations
Support 3D DLP Link
•
•
•
•
•
•
•
•
Color management allowing color adjustments to your liking
Less than 1W power consumption when power saving mode is turned on
Screen Color correction allowing projection on surfaces of several predefined colors
Quick auto search speeding up the signal detecting process
Up to 10 sets of picture modes providing multiple choices for different projection
purposes
•
•
•
•
•
•
•
•
•
Selectable quick power off function
One-key auto-adjustment to display the best picture quality
Digital keystone correction to correct distorted images
Adjustable color balance control for data/video display
High brightness projection lamp
Ability to display 1.07 billion colors
Multi-language On-Screen Display (OSD) menus
Switchable normal and economic modes to reduce the power consumption
Component HDTV compatibility (YPbPr)
•
The apparent brightness of the projected image will vary depending on the ambient
lighting conditions, selected input signal contrast/brightness settings, and is directly
proportional to projection distance.
•
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Shipping contents
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6653w/PJD6653ws/
PJD6683w/PJD6683ws
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
Projector
Power Cord
VGA Cable
PJD5126/PJD6223/
PJD5226/PJD5226w
PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6553w/PJD6253/
PJD6383/PJD6383s
PJD6683w/PJD6683ws
Remote Control &
Batteries
Multi-language user manual DVD
Quick Start Guide
Optional accessories
1.
2.
3.
Replacement lamp
Soft carry case
VGA-Component adapter
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Projector exterior view
1.
External control panel
(See "Projector" on page 7 for
details.)
Front/upper side
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
2.
3.
4.
5.
6.
7.
8.
9.
Lamp cover
1
2
Vent (heated air exhaust)
Quick-release button
Focus and Zoom ring
Front IR remote sensor
Projection lens
Type B USB port
RJ45 LAN input port
5
3
6
7
4
10. RS-232 control port
11. HDMI port
12. RGB signal output socket
13. RGB (PC)/Component video
(YPbPr/YCbCr) signal input
socket-1/2
PJD6353/PJD6353s/PJD6383/PJD6383s
PJD6653w/PJD6653ws/PJD6683w
PJD6683ws
1
2
5
14. S-Video input socket
15. Video input socket
16. Audio signal input socket
Audio signal output socket
17. Kensington anti-theft lock slot
18. AC power cord inlet
19. Rear adjuster foot
3
6
7
4
20. Quick-release foot
21. Security bar
Rear/lower side
PJD5126/PJD5226/PJD5226w
Connects a commercially available
theft prevention cable.
8
10
12
13
14 15 16
Audio in
TYPE
USB
B
MONITOR OUT
COMPUTER IN
1
COMPUTER IN
2
S-Viseo
Video
RS-232
Audio out
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383
PJD6383s/PJD6653w/PJD6653ws/PJD6553w/
PJD6683w/PJD6683ws
8
9
10 11
12
13 14 15 16
17
18
21
19
20
Warning
THIS APPARATUS MUST BE EARTHED.
•
•
When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Controls and functions
Projector
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
1
1
2
3
8
9
10
11
12
13
3
8
9
10
11
12
13
4
5
3
6
7
4
5
3
6
7
MENU
EXIT
MENU
EXIT
1.
2.
3.
Focus ring
Adjusts the focus of the projected image.
Zoom ring
9.
Right
Activates panel key lock.
When the On-Screen Display (OSD)
menu is activated, the #3, #4, and #9 keys
are used as directional arrows to select the
desired menu items and to make
adjustments.
Adjusts the size of the image.
Keystone/Arrow keys (
/
Up,
/
Down)
Manually corrects distorted images
resulting from an angled projection.
10. LAMP indicator light
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
4.
5.
Left/Blank
Hides the screen picture.
POWER indicator light
Lights up or flashes when the projector is
under operation.
11. AUTO
Automatically determines the best picture
timings for the displayed image.
12. TEMPerature indicator light
Lights up red if the projector's
temperature becomes too high.
13. MODE/ENTER
I
POWER
Toggles the projector between standby
mode and on.
SOURCE
Displays the source selection bar.
Top IR remote sensor
Not available for the PJD5126/PJD5226/
PJD5226w.
MENU/EXIT
6.
7.
Selects an available picture setup mode.
Enacts the selected On-Screen Display
(OSD) menu item.
8.
Turns on the On-Screen Display (OSD)
menu. Goes back to previous OSD menu,
exits and saves menu settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Remote control
PJD5126/PJD5226/PJD5226w/ PJD6253/PJD6383/PJD6383s/
PJD6553w/PJD6683w
PJD6683ws
PJD6223/PJD6353/PJD6353s
PJD6653w/PJD6653ws
1
1
18
25
2
3
4
5
2
3
4
5
6
4
8
6
4
8
7
19
7
19
9
10
9
10
20
20
11
12
13
15
16
17
18
12
11
15
16
17
21
14
22
21
14
22
23
24
23
24
To use the remote mouse control
keys (Page Up, Page Down, , and
), see "Using the remote mouse
control" on page 10 for details.
5.
6.
/
/
/
Selects the desired menu items and
makes adjustments.
Enter/
Enacts the selected On-Screen Display
(OSD) menu item.
I
1.
2.
POWER
Toggles the projector between standby
mode and on.
Source selection keys (VGA 1/VGA
2/Video)
Selects an input source for display.
Performs the same function as the left
mouse button when the mouse mode is
activated.
7.
My Button
Allows user to define a short cut key
on the remote control, and the function
item is selected in OSD menu.
Menu
Turns on the On-Screen Display
(OSD) menu.
Mouse
Video/
Selects Video, S-Video or HDMI
source for display.
8.
9.
Performs the same function as the
right mouse button when the mouse
mode is activated.
3.
4.
Source
Switches between the normal and
mouse modes.
Displays the source selection bar.
Keystone keys (
Manually corrects distorted images
resulting from an angled projection.
/
)
Page Up, Page Down,
,
: active
after pressing Mouse. An icon appears
on the screen to indicate the activation
of the mouse mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
21. Volume keys (+, -)
10. Lock
Activates or deactivates panel key lock.
11. Aspect
Selects the display aspect ratio.
12. Magnify
Displays the zoom bar that magnifies or
reduces the projected picture size.
13. Info
Displays the INFORMATION menu.
14. Freeze
Freezes the projected image.
15. Pattern
Displays embedded test pattern.
16. Blank
Hides the screen picture.
17. DynamicEco™
Magnifies or reduces the volume level.
22.
Toggles the projector audio between on
and off.
23. Color Mode
Selects an available picture setup mode.
24. Timer
Displays the presentation timer settings
menu.
25. Laser
Emits visible laser pointer light for
presentation purposes.
Operating the Laser pointer
The Laser Pointer is a presentation aid for
professionals. It emits red colored light when
you press it and the indicator lights up red.
Decreases the power consumption of the
lamp by up to 70%.
It takes some time to initiate this
function. Make sure the projector has
been turned on for more than 4
minutes.
The laser beam is visible. It is necessary to
press and hold LASER for continuous output.
If the projector is resumed by using the
Smart Restart feature, this function can
be executed immediately.
The laser pointer is not a toy. Parents should be
mindful of the dangers of laser energy and keep
this remote control out of the reach of children.
18. Auto Sync
Automatically determines the best picture
Do not look into the laser light window
or shine the laser light beam on
yourself or others. See the warning
messages on the back of the remote
control prior to using it.
timings for the displayed image.
19. Exit
Goes back to previous OSD menu, exits
and saves menu settings.
20. PgUp (Page Up)/PgDn (Page Down)
Operates your display software program
(on a connected PC) which responds to
page up/down commands (like Microsoft
PowerPoint) when the mouse mode is
activated.
Remote control code
The projector can be assigned to two different remote control codes, A or B. When several
adjacent projectors are in operation at the same time, switching the remote control codes
can prevent interference from other remote controls. Set the remote control code for the
projector first before changing that for the remote control.
To switch the code for the projector, select A or B in the SYSTEM SETUP: Advanced >
Remote Control Code menu.!
Download from Www.Somanuals.com. All Manuals Search And Download.
9
To switch the code for the remote control, press PgUp and PgDn buttons on the remote
control together for 5 seconds or more. The initial code is set to A.
If different codes are set on the projector and remote control, there will be no response from
the remote control. When that happens, switch the code for the remote control again.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1.
Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer" on
page 18 for details.
2.
3.
Set the input signal to D-Sub / Comp. 1, D-Sub / Comp. 2 or HDMI.
Press Mouse on the remote control to switch from the normal mode to the mouse
mode. An icon appears on the screen to indicate the activation of the mouse mode.
Perform the desired mouse controls on your remote control.
4.
•
•
To move the cursor on the screen, press
/
/
/
.
To left-click, press
To right-click, press
.
•
•
.
To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
•
To return to the normal mode, press Mouse again or other keys except for the
mouse related multi-function keys.
Remote control effective range
Infra-Red (IR) remote control sensors are located on the front and the top of the projector.
The remote control must be held at an angle within 30 degrees perpendicular to the
projector's IR remote control sensors to function correctly. The distance between the remote
control and the sensors should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote control and the IR sensors on the
projector that might obstruct the infra-red beam.
•
Operating the projector from the
top
•
Operating the projector from the
front
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Replacing the remote control batteries
1.
2.
3.
To open the battery cover, turn the remote control over to view its back, push on the
finger grip on the cover and slide it in the direction of the arrow as illustrated. The
cover will slide off.
Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
Refit the cover by aligning it with the base and sliding it back down into position.
Stop when it clicks into place.
•
Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
•
•
Replace only with the same or equivalent type recommended by the battery manufacturer.
Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
•
•
Never throw the batteries into a fire. There may be danger of an explosion.
If the batteries are dead or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of four possible installation locations:
1.
Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2.
Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the
screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETUP:
Basic > Projector Position menu after you turn
the projector on.
3.
Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM SETUP: Basic
> Projector Position menu after you turn the
projector on.
4.
Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM SETUP: Basic >
Projector Position menu after you turn the
projector on.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Projection dimensions
Refer to "Dimensions" on page 66 for the center of lens dimensions of this projector before
calculating the appropriate position.
The "screen" mentioned below refers to the projection screen usually consisting of a surface
and a support structure
PJD5126/PJD5226/PJD6223/PJD6253/PJD6353/
PJD6353s/PJD6383/PJD6383s
•
4:3 image on a 4:3 screen
(a)
(b)
(e)
(a)
(f)
(d)
(c)
(c)
(d)
(f)
(e)
(b)
•
16:9 image on a 4:3 screen
(a)
(b)
(a)
(e)
(f)
(d)
(c)
(c)
(d)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
PJD5126/PJD5226/PJD6223
4:3 image on a 4:3 Screen
16:9 image on a 4:3 Screen
(a) Screen
(b) Projection
(b) Projection distance
[m (inch)]
(c) Image (d) Vertical
height offset
[cm (inch)] [cm (inch)]
(c) Image (d) Vertical
height offset
[cm (inch) [cm (inch)]
Size
distance [m (inch)]
[inch (m)]
min.
max.
min.
max.
30 (0.8) 1.1 (45) 1.3 (49) 46 (18)
40 (1.0) 1.5 (60) 1.7 (66) 61 (24)
50 (1.3) 1.9 (75) 2.1 (82) 76 (30)
60 (1.5) 2.3 (90) 2.5 (99) 91 (36)
70 (1.8) 2.7 (105) 2.9 (115) 107 (42)
80 (2.0) 3.0 (120) 3.4 (132) 122 (48)
90 (2.3) 3.4 (135) 3.8 (148) 137 (54)
100 (2.5) 3.8 (150) 4.2 (165) 152 (60)
120 (3.0) 4.6 (180) 5.0 (198) 183 (72)
2
3
4
5
5
6
7
8
9
(0.9) 1.1 (45) 1.3 (49 34 (14) 8.0 (3.2)
(1.2) 1.5 (60) 1.7 (66) 46 (18) 10.7 (4.2)
(1.5) 1.9 (75) 2.1 (82) 57 (23) 13.3 (5.3)
(1.8) 2.3 (90) 2.5 (99) 69 (27) 16.0 (6.3)
(2.1) 2.7 (105) 2.9 (115) 80 (32) 18.7 (7.4)
(2.4) 3.0 (120) 3.4 (132) 91 (36) 21.3 (8.4)
(2.7) 3.4 (135) 3.8 (148) 103 (41) 24.0 (9.5)
(3.0) 3.8 (150) 4.2 (165) 114 (45) 26.7 (10.5)
(3.6) 4.6 (180) 5.0 (198) 137 (54) 32.0 (12.6)
150 (3.8) 5.7 (225) 6.3 (247) 229 (90) 11 (4.5) 5.7 (225) 6.3 (247) 171 (68) 40.0 (15.8)
200 (5.1) 7.6 (300) 8.4 (330) 305 (120) 15 (6.0) 7.6 (300) 8.4 (330) 229 (90) 53.3 (21.0)
250 (6.4) 9.51 (375) 10.5 (412) 381 (150) 19 (7.5) 9.51 (375) 10.5 (412) 286 (113) 66.7 (26.3)
300 (7.6) 11.4 (450) 12.6 (495) 457 (180) 23 (9.0) 11.4 (450) 12.6 (495) 343 (135) 80.0 (31.5)
Download from Www.Somanuals.com. All Manuals Search And Download.
13
PJD6253
4:3 image on a 4:3 Screen
(b) Projection
distance [m (inch)]
min. max.
16:9 image on a 4:3 Screen
(b) Projection distance
(a) Screen
(c) Image (d) Vertical
height offset
[cm (inch)] [cm (inch)]
(c) Image (d) Vertical
height offset
[cm (inch) [cm (inch)]
Size
[m (inch)]
min. max.
[inch (m)]
30 (0.8) 0.9 (36) 1.2 (47) 46 (18)
40 (1.0) 1.2 (48) 1.6 (63) 61 (24)
50 (1.3) 1.5 (61) 2.0 (79) 76 (30)
60 (1.5) 1.8 (73) 2.4 (94) 91 (36)
70 (1.8) 2.2 (85) 2.8 (110) 107 (42)
80 (2.0) 2.5 (97) 3.2 (126) 122 (48)
3
5
6
7
8
9
(1.4) 0.9 (36) 1.2 (47) 34 (14) 9.1 (3.6)
(1.8) 1.2 (48) 1.6 (63) 46 (18) 12.2 (4.8)
(2.3) 1.5 (61) 2.0 (79) 57 (23) 15.2 (6.0)
(2.7) 1.8 (73) 2.4 (94) 69 (27) 18.3 (7.2)
(3.2) 2.2 (85) 2.8 (110) 80 (32) 21.3 (8.4)
(3.6) 2.5 (97) 3.2 (126) 91 (36) 24.4 (9.6)
90 (2.3) 2.8 (109) 3.6 (142) 137 (54) 10 (4.1) 2.8 (109) 3.6 (142) 103 (41) 27.4 (10.8)
100 (2.5) 3.1 (121) 4.0 (157) 152 (60) 11 (4.5) 3.1 (121) 4.0 (157) 114 (45) 30.5 (12.0)
120 (3.0) 3.7 (145) 4.8 (189) 183 (72) 14 (5.4) 3.7 (145) 4.8 (189) 137 (54) 36.6 (14.4)
150 (3.8) 4.6 (182) 6.0 (236) 229 (90) 17 (6.8) 4.6 (182) 6.0 (236) 171 (68) 45.7 (18.0)
200 (5.1) 6.2 (242) 8.0 (315) 305 (120) 23 (9.0) 6.2 (242) 8.0 (315) 229 (90) 61.0 (24.0)
250 (6.4) 7.7 (303) 10.0 (394) 381 (150) 29 (11.3) 7.7 (303) 10.0 (394) 286 (113) 76.2 (30.0)
300 (7.6) 9.2 (363) 12.0 (472) 457 (180) 34 (13.5) 9.2 (363) 12.0 (472) 343 (135) 91.4 (36.0)
PJD6353/PJD6353s/PJD6383/PJD6383s
4:3 image on a 4:3 Screen
16:9 image on a 4:3 Screen
(c) Image (d) Vertical
height offset
(a) Screen
Size
(c) Image
height
(d) Vertical
offset
(b) Projection
distance [m (inch)]
(b) Projection
distance [m (inch)]
[inch (m)]
[cm (inch)] [cm (inch)]
[cm (inch) [cm (inch)]
34 (14) 12.6 (5.0)
46 (18) 16.8 (6.6)
57 (23) 21.0 (8.3)
69 (27) 25.1 (9.9)
80 (32) 29.3 (11.6)
91 (36) 33.5 (13.2)
103 (41) 37.7 (14.9)
114 (45) 41.9 (16.5)
137 (54) 50.3 (19.8)
171 (68) 62.9 (24.8)
229 (90) 83.8 (33.0)
286 (113) 104.8 (41.3)
343 (135) 125.7 (49.5)
30
40
(0.8)
(1.0)
(1.3)
(1.5)
(1.8)
(2.0)
(2.3)
(2.5)
(3.0)
(3.8)
(5.1)
(6.4)
(7.6)
0.4
0.5
0.6
0.7
0.9
1.0
1.1
1.2
1.5
1.9
2.5
3.1
3.7
(15)
(19)
(24)
(29)
(34)
(39)
(44)
(49)
(58)
(73)
(97)
(122)
(146)
46
61
76
(18)
(24)
7
9
(2.7)
(3.6)
0.4
0.5
0.6
0.7
0.9
1.0
1.1
1.2
(15)
(19)
(24)
(29)
(34)
(39)
(44)
(49)
(58)
(73)
(97)
(122)
(146)
50
60
(30) 11 (4.5)
(36) 14 (5.4)
(42) 16 (6.3)
(48) 18 (7.2)
(54) 21 (8.1)
(60) 23 (9.0)
91
70
80
90
107
122
137
152
183
229
100
120
150
200
250
300
(72) 27 (10.8) 1.5
(90) 34 (13.5) 1.9
305 (120) 46 (18.0) 2.5
381 (150) 57 (22.5) 3.1
457 (180) 69 (27.0) 3.7
Download from Www.Somanuals.com. All Manuals Search And Download.
14
PJD5226w/PJD6553w/PJD6653w/PJD6653ws/
PJD6683w/PJD6683ws/
•
16:10 image on a 16:10 screen
(a)
(b)
(e)
(a)
(f)
(d)
(c)
(d)
(c)
(f)
(b)
(e)
•
16:10 image on a 4:3 screen
(b)
(a)
(a)
(e)
(f)
(d)
(c)
(d)
(c)
(f)
(b)
(e)
(e): Screen
(f): Center of lens
PJD5226w
16:10 image on a 16:10 Screen
(b) Projection distance
[m (inch)]
min. max.
16:10 image on a 4:3 Screen
(a) Screen
Size
[inch (m)]
(b) Projection distance
[m (inch)]
(c) Image (d)Vertical
height offset
[cm (inch)] [cm (inch)]
(c) Image (d) Vertical
height
offset
[cm (inch) [cm (inch)]
min.
max.
30 (0.8) 0.97 (38) 1.06 (42) 40 (16)
40 (1.0) 1.29 (51) 1.42 (56) 54 (21)
50 (1.3) 1.61 (64) 1.77 (70) 67 (26)
60 (1.5) 1.94 (76) 2.13 (84) 81 (32)
70 (1.8) 2.26 (89) 2.48 (98) 94 (37)
80 (2.0) 2.58 (102) 2.84 (112) 108 (42)
90 (2.3) 2.90 (114) 3.19 (126) 121 (48)
100 (2.5) 3.23 (127) 3.55 (140) 135 (53)
120 (3.0) 3.87 (152) 4.26 (168) 162 (64)
150 (3.8) 4.84 (191) 5.32 (210) 202 (79)
200 (5.1) 6.45 (254) 7.10 (279) 269 (106)
250 (6.4) 8.06 (318) 8.87 (349) 337 (132)
300 (7.6) 9.68 (381) 10.65 (419) 404 (159)
0
0
0
0
0
0
0
0
0
0
0
0
0
(0.0) 0.91 (36) 1.00 (40)
(0.0) 1.22 (48) 1.34 (53)
(0.0) 1.52 (60) 1.67 (66)
(0.0) 1.83 (72) 2.01 (79)
(0.0) 2.13 (84) 2.34 (92)
(0.0) 2.43 (96) 2.68 (105) 102 (40) 10.2 (4.5)
(0.0) 2.74 (108) 3.01 (119) 114 (45) 11.4 (4.5)
(0.0) 3.04 (120) 3.35 (132) 127 (50) 12.7 (5.0)
(0.0) 3.65 (144) 4.02 (158) 152 (60) 15.2 (6.0)
(0.0) 4.56 (180) 5.02 (198) 191 (75) 19.1 (7.5)
(0.0) 6.09 (240) 6.70 (264) 254 (100) 25.4 (10.0)
(0.0) 7.61 (300) 8.37 (329) 318 (125) 31.8 (12.5)
(0.0) 9.13 (359) 10.04 (395) 381 (150) 38.1 (15.0)
38 (15) 3.8 (1.5)
51 (20) 5.1 (2.0)
64 (25) 6.4 (2.5)
76 (30) 7.6 (3.0)
89 (35) 8.9 (3.5)
Download from Www.Somanuals.com. All Manuals Search And Download.
15
PJD6553w
16:10 image on a 16:10 Screen
(b) Projection distance
[m (inch)]
min. max.
16:10 image on a 4:3 Screen
(b) Projection distance
[m (inch)]
max.
(a) Screen
(c) Image (d)Vertical
height offset
[cm (inch)] [cm (inch)]
(c) Image (d) Vertical
Size
height
offset
[inch (m)]
[cm (inch) [cm (inch)]
min.
30 (0.8) 0.78 (31) 1.02 (40) 40 (16)
40 (1.0) 1.05 (41) 1.36 (54) 54 (21)
50 (1.3) 1.31 (51) 1.70 (67) 67 (26)
60 (1.5) 1.57 (62) 2.04 (80) 81 (32)
70 (1.8) 1.83 (72) 2.38 (94) 94 (37)
80 (2.0) 2.09 (82) 2.72 (107) 108 (42)
90 (2.3) 2.35 (93) 3.06 (120) 121 (48)
100 (2.5) 2.61 (103) 3.40 (134) 135 (53)
120 (3.0) 3.14 (124) 4.08 (161) 162 (64)
150 (3.8) 3.92 (154) 5.10 (201) 202 (79)
200 (5.1) 5.23 (206) 6.80 (268) 269 (106)
250 (6.4) 6.54 (257) 8.50 (335) 337 (132)
1
1
2
2
2
3
3
3
4
5
7
8
(0.4) 0.74 (36) 0.96 (38)
(0.5) 0.99 (48) 1.28 (50)
(0.7) 1.23 (61) 1.60 (63)
(0.8) 1.48 (73) 1.92 (76)
(0.9) 1.73 (85) 2.24 (88)
(1.1) 1.97 (97) 2.57 (101) 102 (40) 10.2 (4.5)
(1.2) 2.22 (109) 2.89 (114) 114 (45) 11.4 (4.5)
(1.3) 2.47 (121) 3.21 (126) 127 (50) 12.7 (5.0)
(1.6) 2.96 (145) 3.85 (151) 152 (60) 15.2 (6.0)
(2.0) 3.70 (182) 4.81 (189) 191 (75) 19.1 (7.5)
(2.6) 4.93 (242) 6.41 (252) 254 (100) 25.4 (10.0)
(3.3) 6.17 (303) 8.02 (316) 318 (125) 31.8 (12.5)
38 (15) 3.8 (1.5)
51 (20) 5.1 (2.0)
64 (25) 6.4 (2.5)
76 (30) 7.6 (3.0)
89 (35) 8.9 (3.5)
300 (7.6) 7.84 (309) 10.20 (401) 404 (159) 10 (4.0) 7.40 (363) 9.62 (379) 381 (150) 38.1 (15.0)
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
16:10 image on a 16:10 Screen
16:10 image on a 4:3 Screen
(c) Image (d) Vertical
height offset
(a) Screen
Size
(c) Image
height
(d) Vertical
offset
(b) Projection
distance [m (inch)]
(b) Projection
distance [m (inch)]
[inch (m)]
[cm (inch)] [cm (inch)]
[cm (inch) [cm (inch)]
38 (15) 3.8 (1.5)
51 (20) 5.1 (2.0)
64 (25) 6.4 (2.5)
76 (30) 7.6 (3.0)
89 (35) 8.9 (3.5)
102 (40) 10.2 (4.0)
114 (45) 11.4 (4.5)
127 (50) 12.7 (5.0)
152 (60) 15.2 (6.0)
191 (75) 19.1 (7.5)
254 (100) 25.4 (10.0)
318 (125) 31.8 (12.5)
381 (150) 38.1 (15.0)
30
40
(0.8) 0.32
(1.0) 0.42
(12)
40
54
(16)
(21)
(26)
(32)
(37)
(42)
(48)
(53)
(64)
2
3
3
4
5
5
6
7
8
(0.8) 0.30
(12)
(16)
(20)
(23)
(27)
(31)
(35)
(39)
(47)
(59)
(78)
(98)
(117)
(17)
(21)
(25)
(29)
(33)
(37)
(41)
(50)
(62)
(83)
(104)
(124)
(1.1) 0.40
(1.3) 0.50
(1.6) 0.60
(1.9) 0.70
(2.1) 0.79
(2.4) 0.89
(2.6) 0.99
(3.2) 1.19
50
60
70
(1.3) 0.53
(1.5) 0.63
(1.8) 0.74
(2.0) 0.84
(2.3) 0.95
(2.5) 1.05
(3.0) 1.26
(3.8) 1.58
(5.1) 2.11
(6.4) 2.63
(7.6) 3.16
67
81
94
80
90
108
121
135
162
202
100
120
150
200
250
300
(79) 10 (4.0) 1.49
269 (106) 13 (5.3) 1.99
337 (132) 17 (6.6) 2.48
404 (159) 20 (7.9) 2.98
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Connection
When connecting a signal source to the projector, be sure to:
1.
2.
3.
Turn all equipment off before making any connections.
Use the correct signal cables for each source.
Ensure the cables are firmly inserted.
•
•
•
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
The connection illustrations below are for reference only. The rear connecting jacks
available on the projector vary with each projector model.
For detailed connection methods, see pages 18-21.
Notebook or
desktop computer
A/V device
Monitor
(VGA)
(DVI)
or
1
7
1
2
3
7
Speakers
8
4
7
5
6
S-Viseo
Video
Audio in
PJD6223/PJD6253/
PJD6353/PJD6353s/
PJD6383/PJD6383s/
PJD6553w/PJD6653w/
PJD6653ws/PJD6683w/
PJD6683ws
1
2
HDMI
TYPE
USB
B
COMPUTER IN
COMPUTER IN
1
2
RS-232
MONITOR OUT
LAN
Audio
out
Audio in
TYPE
USB
B
PJD5126/PJD5226/
PJD5226w
MONITOR OUT
COMPUTER IN
1
COMPUTER IN
2
RS-232
Video
S-Viseo
Audio out
1.
2.
3.
4.
VGA cable
VGA to DVI-A cable
USB cable
Component Video to VGA (D-Sub)
adapter cable
5.
6.
7.
8.
S-Video cable
Video cable
Audio cable
HDMI cable
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Connecting a computer or monitor
Connecting a computer
The projector provides two VGA input sockets that allow you to connect them to both
IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are
connecting legacy version Macintosh computers.
To connect the projector to a notebook or desktop computer:
1.
2.
3.
Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER
IN 2 signal input socket on the projector.
If you wish to use the remote paging function, take a USB cable and connect the
larger end to the USB port of the computer, and smaller end to the Type B USB socket
on the projector. See "Using the remote mouse control" on page 10 for details.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
To connect the projector to a monitor:
1.
Connect the projector to a computer as described in "Connecting a computer" on page
18.
Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
2.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
Connect the other end of the cable to the MONITOR OUT socket on the projector.
3.
•
For the PJD5126/PJD5226/PJD5226w, the MONITOR OUT output only works when
COMPUTER IN 1 is made to the projector.
•
•
For the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383sPJD6553w/PJD6653w/
PJD6653ws/PJD6683w/PJD6683ws,
MONITOR OUT output only works when
the projector.
COMPUTER IN 1 or COMPUTER IN 2 is made to
To use this connection method when the projector is in standby mode, turn on the Active
VGA Out function under the SYSTEM SETUP: Advanced > Standby Settings menu.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
•
•
•
•
HDMI
Component Video
S-Video
Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with a HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 20 for how to connect the projector to a HDMI
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 20 for how to connect the
projector to a component video device.
Better video quality
The S-Video method provides a better quality analog video than standard composite Video.
If you have both composite Video and S-Video output terminals on your Video source
device, you should elect to use the S-Video option.
See "Connecting an S-Video source device" on page 21 for how to connect the projector to
an S-Video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See "Connecting a composite Video source device" on page 21 for how to connect the
projector to a composite Video device.
Connecting audio
The projector has one built-in mono speaker which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. They are not
designed for, nor intended for stereo audio reproduction use as might be expected in home
theater or home cinema applications. Any stereo audio input (if provided), is mixed into a
common mono audio output through the projector speaker.
The table below describes where the sound is from when different source is connected.
Input source
The projector can play
the sound from...
COMPUTER IN 1
AUDIO IN 1
COMPUTER IN 2, VIDEO, S-VIDEO
AUDIO IN 2
Download from Www.Somanuals.com. All Manuals Search And Download.
19
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a mixed mono signal and controlled by the projector Volume and Mute
settings.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
To connect the projector to an HDMI device:
1.
Take an HDMI cable and connect one end to the HDMI-output port of the video
device.
Connect the other end of the cable to the HDMI-input port on the projector.
2.
•
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color
space to YUV. See "Changing Color Space" on page 27 for details.
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
The HDMI input port is only available on the PJD6223/PJD6253/PJD6553w series.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a Component Video source device:
1.
Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3
RCA type connectors to the Component Video output sockets of the Video source
device. Match the color of the plugs to the color of the sockets; green to green, blue to
blue, and red to red.
Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a
D-Sub type connector) to the COMPUTER IN 1 or COMPUTER IN 2 socket on the
projector.
2.
•
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
VGA-Component adapter
(ViewSonic P/N: CB-00008906)
•
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Connecting an S-Video source device
Examine your Video source device to determine if it has an unused S-Video output socket
available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to an S-Video source device:
1.
Take an S-Video cable and connect one end to the S-Video output socket of the Video
source device.
Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
2.
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
•
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
If you have already made a Component Video connection between the projector and this
S-Video source device using Component Video connections, you need not connect to this
device using an S-Video connection as this makes an unnecessary second connection of
poorer picture quality. See "Connecting Video source devices" on page 19 for details.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
•
•
If so, you can continue with this procedure.
If not, you will need to reassess which method you can use to connect to the device.
To connect the projector to a composite Video source device:
1.
Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
Connect the other end of the Video cable to the VIDEO socket on the projector.
2.
•
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 19 for details.
•
•
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
You need only connect to this device using a composite Video connection if Component
Video and S-Video inputs are unavailable for use. See "Connecting Video source devices"
on page 19 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Operation
Starting up the projector
1.
Plug the power cord into the projector and into a
wall socket. Turn on the wall socket switch
(where fitted). Check that the POWER
indicator light on the projector flashes blue
after power has been applied.
I
2.
Press
POWER on the projector or remote
control to start the projector. The POWER
indicator light stays blue when the projector is
on.
(If necessary) Rotate the focus ring to adjust the image clearness.
•
If the projector is still hot from previous activity, it will run the cooling fan for
approximately 90 seconds before energizing the lamp.
•
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before
turning it off.
3.
If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
4.
5.
Switch all of the connected equipment on.
The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press SOURCE on the projector or remote control to select your desired
input signal. See "Switching input signal" on page 27 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 67 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Using the menus
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
Main menu icon
Screen Color
Off
Aspect Ratio
Keystone
Position
Phase
H. Size
Zoom
Auto
Highlight
Sub-menu
ENTER
Status
16
0
Go to the
3D Sync
3D Sync Invert
Color Management
On
Disable
previous page
or to exit.
MENU Exit
Current input
signal
Analog RGB
To use the OSD menus, please set them to your familiar language first.
1.
Press MENU/EXIT on the projector or
Menu on the remote control to turn the
OSD menu on.
3.
Press
Language and press
select a preferred language.
to highlight
/
to
Screen Color
Aspect Ratio
Keystone
Off
Language
English
Auto
Projector Position
Auto Power Off
Blank Timer
Front Table
Disable
Disable
Off
Position
Phase
16
0
Panel Key Lock
H. Size
Zoom
Timer Controller
Splash Screen
Screen Capture
Message
Disable
ViewSonic
3D Sync
On
Disable
3D Sync Invert
Color Management
Analog RGB
On
LAN Control Settings
Analog RGB
Exit
MENU
MENU Exit
4.
Press MENU/EXIT twice* on
the projector or Exit on the
remote control to leave and
save the settings.
*The first press leads you back
to the main menu and the
second press closes the OSD
menu.
2.
Use
/
to highlight the SYSTEM
SETUP: Basic menu.
Language
English
Projector Position
Auto Power Off
Blank Timer
Front Table
Disable
Disable
Panel Key Lock
Timer Controller
Splash Screen
Off
Disable
ViewSonic
On
Screen Capture
Message
LAN Control Settings
Analog RGB
MENU Exit
: DISPLAY
: PICTURE
: SOURCE
: SYSTEM SETUP: Basic
: SYSTEM SETUP: Advanced
: INFORMATION
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 23.
You will be inconvenienced if you activate the password functionality and subsequently forget
the password. Print this user manual (if necessary) and write the password you used in this
manual, and keep it in a safe place for later use.
Setting a password
1.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings menu. Press MODE/ENTER on the projector or Enter on the remote
control. The Security Settings page is displayed.
2.
3.
Highlight Power On Lock and select On by pressing
As pictured to the right, the four arrow keys
/
.
INPUT NEW PASSWORD
(
,
,
,
) respectively represent 4 digits
(1, 2, 3, 4). According to the password you desire
to set, press the arrow keys to enter six digits for
the password.
4.
5.
Confirm the new password by re-entering the
new password.
MENU Back
Once the password is set, the OSD menu returns to the Security Settings page.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
•
•
Once a password has been set, the projector cannot be used unless the correct password
is entered every time the projector is started.
The digits being input will be displayed as asterisks on-screen. Write your selected
password down here in this user manual in advance or right after the password is entered
so that it is available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
If you forget the password
If the password function is activated, you will be asked
to enter the six-digit password every time you turn on
the projector. If you enter the wrong password, the
password error message as pictured to the right is
displayed lasting for three seconds, and the message
'INPUT PASSWORD' follows. You can retry by
entering another six-digit password, or if you did not
Password Error
Please try again.
record the password in this user manual, and you absolutely do not remember it, you can use
the password recall procedure. See "Entering the password recall procedure" on page 25 for
details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Entering the password recall procedure
1.
Press and hold AUTO on the projector or Auto
Sync on the remote control for 3 seconds. The
projector will display a coded number on the
screen.
RECALL PASSWORD
Please write down the recall code,
and contact ViewSonic
Customer Center.
Recall code:
2.
3.
Write down the number and turn off your
projector.
Seek help from the local service center to decode
the number. You may be required to provide
0 2 1 2
Exit
MENU
proof of purchase documentation to verify that you are an authorized user of the
projector.
Changing the password
1.
2.
3.
Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security
Settings > Change Password menu.
Press MODE/ENTER on the projector or Enter on the remote control. The message
'INPUT CURRENT PASSWORD' is displayed.
Enter the old password.
•
If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT CURRENT PASSWORD' is
displayed for your retry. You can press MENU/EXIT on the projector or Exit
on the remote control to cancel the change or try another password.
4.
5.
6.
Enter a new password.
Confirm the new password by re-entering the new password.
You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
To leave the OSD menu, press MENU/EXIT on the projector or Exit on the remote
control.
7.
The digits being input will be displayed as asterisks on-screen. Write your selected password
down here in this user manual in advance or right after the password is entered so that it is
available to you should you ever forget it.
Password: __ __ __ __ __ __
Keep this user manual in a safe place.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Disabling the password function
To disable password protection, go back to the SYSTEM SETUP: Advanced > Security
Settings > Power On Lock menu after opening the OSD menu system. Select Off by
pressing
/
. The message 'INPUT PASSWORD' is displayed. Enter the current
password.
•
If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
•
If the password is incorrect, the password error message is displayed lasting for
three seconds, and the message 'INPUT PASSWORD' is displayed for your
retry. You can press MENU/EXIT on the projector or Exit on the remote
control to cancel the change or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SOURCE menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by
PJD5126/PJD5226/PJD5226w
pressing one of the source selection keys on the
remote control, or cycle through the available input
D-Sub / Comp. 1
signals.
1.
Press SOURCE on the projector or remote
control. A source selection bar is displayed.
D-Sub / Comp. 2
Video
2.
Press
/
until your desired signal is
selected and press MODE/ENTER on the
projector or Enter on the remote control.
Once detected, the selected source information
will be displayed on the screen for seconds. If
there are multiple devices connected to the
projector, repeat steps 1-2 to search for another
signal.
S-Video
PJD6223/PJD6253/PJD6353/
PJD6353s/PJD6383/PJD6383s/
PJD6553w/PJD6653w/PJD6653ws
PJD6683w/PJD6683ws
•
The brightness level of the projected image will
change accordingly when you switch between
different input signals. Data (graphic) "PC"
presentations using mostly static images are
generally brighter than "Video" using mostly
moving images (movies).
The input signal type effects the options available
for the Color Mode. See "Selecting a picture
mode" on page 32 for details.
Please see "Projector specifications" on page 64
for the native display resolution of this projector.
For best display picture results, you should select
and use an input signal which outputs at this
resolution. Any other resolutions will be scaled by
the projector depending upon the 'aspect ratio'
setting, which may cause some image distortion
or loss of picture clarity. See "Selecting the aspect
ratio" on page 30 for details.
D-Sub / Comp. 1
D-Sub / Comp. 2
HDMI
•
•
Video
S-Video
Changing Color Space
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6553w/
PJD6383s/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws series.
In the unlikely event that you connect the projector to a DVD player via the projector’s
HDMI input and the projected picture displays wrong colors, please change the color space
to YUV.
To do this:
1.
2.
Open the OSD menu and go to the SOURCE menu.
Press to highlight Color Space Conversion and press
color space.
/
to select a suitable
This function is only available when the HDMI-input port is in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with 1 quick-release adjuster foot and 2 rear adjuster feet. These
adjusters change the image height and projection angle. To adjust the projector:
1.
Press the quick-release button and lift the
front of the projector. Once the image is
positioned where you want it, release the
quick-release button to lock the foot in
position.
Screw the rear adjuster feet to fine tune the
horizontal angle.
1
2
2.
To retract the foot, hold up the projector while
pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster
feet in a reverse direction.
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, see "Correcting keystone" on page 29 for details.
•
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
•
Be careful when you press the adjuster button as it is close to the exhaust vent where hot
air comes from.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press AUTO on the
projector or Auto Sync on the remote control. Within 3 seconds, the built-in Intelligent
Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the
best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
•
•
The screen will be blank while AUTO is functioning.
This function is only available when PC signal (analog RGB) is selected.
Fine-tuning the image clarity
1.
Adjust the projected image to the size
that you need using the zoom ring.
2.
If necessary, Sharpen the image by
rotating the focus ring.
PJD5126/PJD5226/
PJD5226w/PJD6223/
PJD6253/PJD6553w
PJD6353/PJD6353s/
PJD6383/PJD6383s/
PJD6653w/PJD6653ws/
PJD6683w/PJ
D6683ws/
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the
top or bottom. It occurs when the projector is not perpendicular to the screen.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
•
Using the remote control
Press
/
on the projector or remote control to
display the Keystone correction page. Press
correct keystoning at the top of the image. Press
to
to correct keystoning at the bottom of the image.
Press
/
.
Press
/
.
•
1.
Using the OSD menu
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the DISPLAY menu is highlighted.
to highlight Keystone and press MODE/ENTER on the projector or Enter
2.
3.
Press
on the remote control. The Keystone correction page is displayed.
Press
to correct keystoning at the top of the image or press
to correct
keystoning at the bottom of the image.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
•
Using the remote control
1.
2.
3.
Press Magnify on the remote control to display the Zoom bar.
Press
repeatedly to magnify the picture to a desired size.
To navigate the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch to the paning mode and press the directional arrows
(
,
,
,
) to navigate the picture.
4.
To reduce size of the picture, press MODE/ENTER on the projector or Enter on the
remote control to switch back to the zoom in/out functionality, and press AUTO/Auto
Sync to restore the picture to its original size. You can also press
repeatedly until
it is restored to the original size.
•
1.
Using the OSD menu
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the DISPLAY menu is highlighted.
2.
3.
Press
to highlight Zoom and press MODE/ENTER on the projector or Enter on
the remote control. The Zoom bar is displayed.
Repeat steps 2-4 in the section of Using the remote control above.
The picture can only be navigated after the picture is magnified. You can further magnify the
picture while searching for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Selecting the aspect ratio
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
•
1.
2.
Using the remote control
Press Aspect to show the current setting.
Press Aspect repeatedly to select an aspect ratio to suit the!format of the video signal
and your display requirements.
Using the OSD menu
•
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the DISPLAY menu is highlighted.
2.
3.
Press
to highlight Aspect Ratio.
Press
/
to select an aspect ratio to suit the format of the video signal and your
display requirements.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.
Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the
image's aspect ratio.
16:10 picture
15:9 picture
2.
4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration.
4:3 picture
3.
4.
16:9: Scales an image so that it is displayed in
the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.
16:9 picture
16:10 (PJD5226w/PJD6553w/PJD6653w/
PJD6653ws/PJD6683w/PJD6683ws only):
Scales an image so that it is displayed in the
center of the screen with a 16:10
aspect ratio.
are
This is most suitable for images which
16:10 picture
already in a 16:10 aspect, as it displays them
without aspect alteration
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
•
Press MODE/ENTER on the projector or Color Mode on the remote control
repeatedly until your desired mode is selected.
•
Go to the PICTURE > Color Mode menu and press
/
to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
PC input signals: D-Sub / Comp. 1/2 (analog RGB)
1.
Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2.
3.
4.
PC mode: Is designed for presentations under daylight environment to match PC and
notebook coloring.
ViewMatch mode: Switches between high brightness performance and accurate color
performance.
Movie mode:!Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
Dynamic PC mode: Is designed for presentations under daylight environment to
match PC and notebook coloring. In addition, the projector will optimize the image
quality using the dynamic PC function in accordance with the projected contents.
5.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6.
Dynamic Movie mode:!Is appropriate for playing colorful movies, video clips from
digital cameras or DVs through the PC input for best viewing in a blackened (little
light) environment. In addition, the projector will optimize the image quality using the
dynamic Movie function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
7.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 33 for details.
Video input signals: S-Video, Video, D-Sub / Comp. 1/2 (YPbPr) / HDMI
1.
Brightest mode: Optimized for daylight viewing, with living room level ambient
brightness.
2.
Gaming mode: Suitable for all types of entertainment media, including gaming and
movies.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
3.
4.
5.
ViewMatch mode: Switches between high brightness performance and accurate color
performance.
Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a
blackened (little light) home cinema or lounge room environment.
Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best
viewed in a blackened (little light) home cinema or lounge room environment. In
addition, the projector will optimize the image quality using the dynamic Movie
function in accordance with the projected contents.
It takes some time to initiate this function. Make sure the projector has been turned on for
more than 4 minutes.
If the projector is resumed by using the Smart Restart feature, this function can be executed
immediately.
6.
User 1/User 2 mode: Recalls the settings customized based on the current available
picture modes. See "Setting the User 1/User 2 mode" on page 33 for details.
Setting the User 1/User 2 mode
There are two user-definable modes if the current available picture modes are not suitable
for your need. You can use one of the picture modes (except the User 1/User 2) as a starting
point and customize the settings.
1.
Press MENU/EXIT on the projector or Menu on the remote control to open the On-
Screen Display (OSD) menu.
Go to the PICTURE > Color Mode menu.
2.
3.
4.
Press
Press
/
to select User 1 or User 2.
to highlight Reference Mode.
This function is only available when User 1 or User 2 mode is selected up in the Color Mode
sub-menu item.
5.
6.
Press
Press
/
to select a picture mode that is closest to your need.
to select a sub-menu item to be changed and adjust the value with
/
.
See Fine-tuning the image quality in user modes below for details.
7.
8.
When all settings have been done, highlight Save Settings and press MODE/ENTER
on the projector or Enter on the remote control to store the settings.
The confirmation message 'Setting Saved' is displayed.
Using Screen Color
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press
/
to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard.
This function is only available when a PC type input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available
when User 1 or User 2 mode is selected. You can make adjustments to these functions
based on your needs.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Adjusting Brightness
Highlight the PICTURE > Brightness menu and press
/
.
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
+50
+70
+30
Adjusting Contrast
Highlight the PICTURE > Contrast menu and press
/
.
.
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
0
+30
-30
Adjusting Color
Highlight the PICTURE > Color menu and press
/
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
Adjusting Tint
Highlight the PICTURE > Tint menu and press
/
.
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
Adjusting Sharpness
Highlight the PICTURE > Sharpness menu and press
/
.
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
Adjusting Brilliant Color
Highlight the PICTURE > Brilliant Color menu and press
/
.
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select On. If you don’t need it, select Off.
When Off is selected, the Color Temperature function is not available.
Selecting a Color Temperature
Highlight the PICTURE > Color Temperature menu and press
/
.
The options available for color temperature* settings vary according to the signal type
selected.
1.
T1: With the highest color temperature, T1 makes the image appear the most bluish
white than other settings.
2.
3.
4.
T2: Makes images appear bluish white.
T3: Maintains normal colorings for white.
T4: Makes images appear reddish white.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
*About color temperatures:
There are many different shades that are considered to be "white" for various purposes. One
of the common methods of representing white color is known as the “color temperature”. A
white color with a low color temperature appears to be reddish white. A white color with a
high color temperature appears to have more blue in it.
Color Management
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1.
2.
Go to the DISPLAY menu and highlight Color Management.
Press MODE/ENTER on the projector or Enter on the remote control and the Color
Management page is displayed.
3.
4.
Highlight Primary Color and press
/
to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
Press
to highlight Hue and press
/
to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
Yellow
GREEN
RED
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
Cyan
Magenta
5.
Press
to highlight Saturation and adjust
its values to your preference by pressing
/
BLUE
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6.
Press
to highlight Gain and adjust its values to your preference by pressing
/
. The contrast level of the primary color you select will be affected. Every
adjustment made will reflect to the image immediately.
Repeat steps 3 to 6 for other color adjustments.
7.
8.
9.
Make sure you have made all of the desired adjustments.
Press MENU/EXIT on the projector or Exit on the remote control to exit and save the
settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1.
Press Timer on the remote control to access the Presentation Timer menu or go to
the SYSTEM SETUP: Advanced > Presentation Timer menu and press MODE/
ENTER to display the Presentation Timer page.
2.
Highlight Timer Period and decide the time period by pressing
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5-
minute increments.
/
. The length of
If the timer is already on, the timer will restart whenever the Timer Period is reset.
3.
Press
to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing
/
.
Selection
Description
Displays the timer on screen throughout the presentation
time.
Always
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
Never
Hides the timer throughout the presentation time.
4.
5.
Press
to highlight Timer Position and set the timer position by pressing
/
.
Top-Left
Bottom-Left
Top-Right
Bottom-Right
Press
to highlight Timer Counting Direction and select your desired counting
direction by pressing
/
.
Selection
Count Up
Description
Increases from 0 to the preset time.
Count Down
Decreases from the preset time to 0.
6.
Press
to highlight Sound Reminder and decide if you want to activate sound
. If you select On, a double beep sound will be heard at
reminder by pressing
/
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
7.
8.
To activate the presentation timer, press
and press
/
to highlight Start
Counting and press MODE/ENTER.
A confirmation message displays. Highlight Yes and press MODE/ENTER on the
projector or remote control to confirm. You will see the message “Timer is On”
displaying on the screen. The timer starts counting when the timer is on.
To cancel the timer, perform the following steps:
1.
Go to the SYSTEM SETUP: Advanced > Presentation Timer menu and highlight
Off. Press MODE/ENTER. A confirmation message displays.
Highlight Yes and press MODE/ENTER to confirm. You will see the message
“Timer is Off” displaying on the screen.
2.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Hiding the image
In order to draw the audience's full attention to the presenter, you can use
on the
projector or Blank on the remote control to hide the screen image. Press any key on the
projector or remote control to restore the image. The word 'BLANK' appears at the lower
right corner of the screen while the image is hidden.
You can set the blank time in the SYSTEM SETUP: Basic > Blank Timer menu to let
the projector return the image automatically after a period of time when there is no action
taken on the blank screen.
Once Blank is pressed, the projector enters Economic mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
I
control keys on the projector will operate except
POWER.
1.
Press
on the projector or Lock
on the remote control, or go to the SYSTEM
SETUP: Basic > Panel Key Lock menu, and select On by pressing
projector or remote control.
A confirmation message is displayed. Select Yes to confirm.
/
on the
2.
To release panel key lock, press and hold
control for 3 seconds.
on the projector or Lock
on the remote
You can also use the remote control to enter the SYSTEM SETUP: Basic > Panel Key
Lock menu and press to select Off.
/
•
•
Keys on the remote control are still functional when panel key lock is enabled.
I
If you press POWER to turn off the projector without disabling panel key lock, the
projector will still be in locked status the next time it is turned on.
Freezing the image
Press Freeze on the remote control to freeze the image. The word 'FREEZE' will be
displayed in the upper left corner of the screen. To release the function, press any key on the
projector or remote control.
Even if an image is frozen on the screen, the pictures are running on the video or other
device. If the connected devices have active audio output, you will still hear the audio even
though the image is frozen on screen.
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 0°C–35°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 0°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
To activate the High Altitude Mode:
Notice
1.
Press MENU/EXIT on the projector or Menu on
We recommend you use the High Altitude
mode by selecting it whenever your
environment is higher than 1500 m.
the remote control and then press
SYSTEM SETUP: Advanced menu is
/
until the
Do you want to turn High Altitude Mode
ON?
highlighted.
2.
3.
Press
to highlight High Altitude Mode and
No
Yes
press
/
to select On. A confirmation
message is displayed.
Highlight Yes and press MODE/ENTER on the projector or Enter on the remote
control.
Operation under "High Altitude Mode" may cause a higher decibel operating noise level
because of increased fan speed necessary to improve overall system cooling and
performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Creating your own startup screen
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws series.
In addition to selecting the projector preset startup screen from among ViewSonic logo,
Black or Blue screen, you can make your own startup screen that is a picture projected from
your computer or video source.
To create your own startup screen, project the picture you want to use as your startup screen
from either a computer or video source. The rest of the steps are as follows.
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the SYSTEM SETUP: Basic menu is highlighted.
2.
3.
4.
5.
Press
to highlight Screen Capture and press MODE/ENTER on the projector or
Enter on the remote control.
A confirmation message is displayed. Press MODE/ENTER on the projector or
Enter on the remote control again.
The message 'Screen Capturing...' is displayed while the projector is processing the
picture. Please wait.
If the action is successful, you see the message 'Capture Succeeded' on the screen.
The captured picture is saved as Screen Capture and the captured picture will be
displayed as the startup screen if you restart the projector.
In the unlikely event that the capturing action fails, change your target picture. When the
resolution of the input signal is higher than the projector’s native display resolution (See
"Projector specifications" on page 64 for details.), the capture action may fail. When it
happens, please set the resolution of the input signal under native resolution and try again.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Controlling the projector through a LAN
environment
This function is only available for the PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s
PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws series.
®
The projector supports Crestron software. With correct settings for the LAN Control
Settings menu, you can manage the projector from a computer using a web browser when
the computer and the projector are properly connected to the same local area network.
TYPE
USB
B
LAN
RS-232
(An example of connection)
Configuring the LAN Control Settings
If you are in a DHCP environment:
1.
Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector
and the other end to the RJ45 port.
Press MENU/EXIT on the projector or Menu on the remote control and then press
2.
/
until the SYSTEM SETUP: Basic menu is highlighted.
3.
Press
to highlight LAN Control Settings and press MODE/ENTER on the
projector or Enter on the remote control. The LAN Control Settings page is
displayed.
4.
5.
Press
Press
to highlight DHCP and press
/
to select On.
to highlight Apply and press MODE/ENTER on the projector or Enter on
the remote control.
6.
Please wait for around 15 - 20 seconds, and then re-enter the LAN Control Settings
page. The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server
settings will be displayed. Note down the IP address displayed in the Projector IP
Address row.
•
•
If the Projector IP Address still does not appear, contact your network administrator.
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
•
If you need to connect to the projector in its standby mode, set Power Saving to Off.
Download from Www.Somanuals.com. All Manuals Search And Download.
39
If you are in a non-DHCP environment:
1.
Repeat steps 1-3 above.
2.
3.
Press to highlight DHCP and press
/
to select Off.
Contact your ITS administrator for information on the Projector IP Address, Subnet
Mask, Default Gateway, and DNS Server settings.
4.
Press
to select the item you want to modify and press MODE/ENTER on the
projector or Enter on the remote control.
5.
6.
Press to move the cursor and the press
/
/
to enter the value.
To save the settings, press MODE/ENTER on the projector or Enter on the remote
control. If you do not want to save the settings, press MENU/EXIT on the projector
or Menu on the remote control.
7.
Press
to highlight Apply and press MODE/ENTER on the projector or Enter on
the remote control.
•
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask,
Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are
properly connected and perform the procedures above again.
•
If you wish to connect to the projector in its standby mode, be sure you have selected
RJ45 and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS
Server information when the projector is on.
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in standby
mode, you can use any computer that is on the same local area network to control the
projector.
•
•
If you are using Microsoft Internet Explorer, make sure it is version 7.0 or higher.
The screen shots in this manual are for reference only, and may differ from the actual
design.
1.
2.
Enter the address of the projector in the address bar of your browser and press Enter.
The main page of the Network Control appears.
3
4
5
Accessing to Network Settings or Email Alert page requires Administrator password. The
default password is "0000".
3.
This page allows you to make adjustments to the AMX and SNMP settings. In the
AMX device discover row, when ON is selected, the projector can be detected by
Download from Www.Somanuals.com. All Manuals Search And Download.
40
controllers of AMX connected to the same network. For the Details of AMX Device
4.
If your projector is connected to a network which supports Simple Mail Transfer
Protocol (SMTP), you can configure it to alert you via email on significant events.
5.
The Crestron (e-Control) page displays the Crestron e-Control user interface. See
"About Crestron e-Control®" on page 42 for details.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Maximum Number
of Characters
Category Item
Input Length
DHCP/Manual
IP Address
Subnet Mask
Gateway
(N/A)
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
XXX.XXX.XXX.XXX
Network
DNS Server
AMX device discovery (N/A)
Network Settings
Administrator
New Password
Confirm Password
SysLocation
SysName
(N/A)
4
4
22
22
22
Password
SNMP
SysContact
Download from Www.Somanuals.com. All Manuals Search And Download.
41
To
40
Cc
Subject
From
Server
User Name
Password
Fan Error
Lamp Error
Over Temperature
Lamp Time Alert
Submit
40
30
40
30
40
14
(N/A)
(N/A)
(N/A)
(N/A)
(N/A)
(N/A)
Email Setting
SMTP Setting
Email Alert
Alert Condition
Issue Test Mail
/ > < $ % + \ ' " are prohibited/
®
About Crestron e-Control
®
1.
The Crestron e-Control page provides a variety of virtual keys to control the
projector or adjust the projected pictures.
i
ii
i
You can press
to reveal
more buttons.
i
/
i. These buttons function the same as the ones on the OSD menus or remote control.
See "2. PICTURE menu" on page 51 and "Projector" on page 7 for details.
ii. To switch between input signals, click on your desired signal.
•
The Menu button can also be used to go back to previous OSD menus, exit and save menu
settings.
•
•
The source list varies according to the connectors available on the projector.
When you use the projector control panel or remote control to change the OSD menu
settings, it may take a while for the web browser to synchronize these changes with the
projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
2.
The tools page allows you to manage the projector, configure the LAN control
settings and secure access of remote network operation on this projector.
i
ii
iv
iii
v
vi
i. This section is only used with the Crestron Control System. Please contact
Creston or refer to its user manual for setup information.
ii. You can name the projector, keep track of its location and the person in charge of
it.
iii. You can adjust the LAN Control Settings.
iv. Once set, access to the remote network operation on this projector has been
password-protected.
v. Once set, access to the tools page has been password-protected.
•
•
To prevent errors, only input the English alphabet and digits on the tools page.
After making the adjustments, press the Send button and the data will be saved for the
projector.
vi. Press Exit to go back to the remote network operation page.
Please pay attention to the limitation of input length (including space and other punctuation
keys) in the list blow:
Maximum Number of
Characters
Category Item
Input Length
IP Address
IP ID
15
2
Crestron Control
Port
5
Projector Name
Location
10
9
Projector
Assigned To
DHCP (Enabled)
IP Address
Subnet Mask
Default Gateway
DNS Server
9
(N/A)
15
15
15
15
Network Configuration
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Enabled
New Password
Confirm
(N/A)
20
2
User Password
Enabled
New Password
Confirm
(N/A)
20
20
Admin Password
3.
The info page displays the information and status of this projector.
Press Exit to
go back to the
remote network
operation page.
4.
After pressing the button “Contact IT Help”, the HELP DESK window will appear in
the upper right corner of the screen. You will be able to deliver messages to
RoomView™ software administrators/users who connect to the same local area
network.
**Crestron RoomView
On the “Edit Room” page, enter the IP Address (or hostname) as shown on the projector’s
on-screen display (OSD) menu, and “02” for IPID, “41794” for the reserved Crestron
control port.
About Crestron RoomView™ setting and command method, please access below website to
get RoomView™ User Guide and more information:
resources.asp
Download from Www.Somanuals.com. All Manuals Search And Download.
44
PJLink™, SNMP, AMX and Xpanel formats supported
This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details,
please follow its user guide or website respectively to control and manage projectors.
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
SYSTEM SETUP: Basic > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
Power Saving
Less than 1W power consumption when Power Saving mode is turned on.
•
•
When Power Saving is On, the following settings are not available.
When Power Saving is On, the network function is not available when the projector is in
standby mode.
Active VGA Out
Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT
sockets are correctly connected to devices. The projector outputs the signal received only
from COMPUTER IN 1.
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN 1 and AUDIO OUT sockets are
correctly connected to devices. The projector outputs the audio signal received only from
AUDIO IN 1.
Quick Power Off
Selecting On enables the function and the projector will not enter the cooling process after
being shut down. Selecting Off disables the function and the projector will enter normal
cooling process after being shut down.
•
If you attempt to restart the projector right after it’s been turned off, it may not be turned
on successfully and will rerun its cooling procedure.
•
When Off is selected, the Smart Restart function will be automatically turned off.
Shutting down the projector
I
1.
Press POWER and a confirmation message
is displayed prompting you.
If you don't respond in a few seconds, the
message will disappear.
I
2.
3.
Press
POWER a second time.
Disconnect the power cord from the wall
socket if the projector will not be used in an
extended period of time.
CAUTION
•
•
•
To protect the lamp, the projector will not respond to any commands during the cooling
process.
To shorten the cooling time, you can also activate the Quick Power Off function. See
"Quick Power Off" on page 45 for details.
Do not unplug the power cord before the projector shutdown sequence is complete.
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
Main menu
Sub-menu
Options
Off/Blackboard/
Screen Color
Aspect Ratio
Greenboard/Whiteboard
Auto/4:3/16:9/
16:10 (
PJD5226w/PJD6553w/
PJD6653w/PJD6653ws/
PJD6683w/ PJD6683ws only)
Keystone
Position
Phase
H. Size
Zoom
1.
DISPLAY
3D Sync
3D Sync Invert
TI 3D DLP Link/Off
Disable/Invert
R/G/B/C/M/Y
Primary Color
Hue
Saturation
Gain
Color
Management
PC source: Brightest/PC/ViewMatch/Movie/
Dynamic PC/Dynamic Movie/User 1/User 2
Video source: Brightest/Gaming/ViewMatch/
Movie/Dynamic Movie/User 1/User 2
Color Mode
PC source: Brightest/PC/ViewMatch/Movie/
Dynamic PC/Dynamic Movie
Video source: Brightest/Gaming/ViewMatch/
Movie/Dynamic Movie
Reference Mode
2.
Brightness
Contrast
Color
PICTURE
Tint
Sharpness
Brilliant Color
On/Off
Color Temperature
Save Settings
T1/T2/T3/T4
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Main menu
Sub-menu
Quick Auto Search
Options
Off/On
Color Space Conversion (PJD6223/
PJD6253/PJD6353/PJD6353s/PJD6383/
PJD6383s/PJD6553w/PJD6653w/PJD6653ws/
RGB/YUV/Auto
only)
PJD6683w/PJD6683ws
Disable/5 min/10 min/15
min/30 min
Off/On
DynamicEco Timer
Smart Restart
PJD5126/PJD5226/PJD5226w: Off/On
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s:
01/02/03/04/05/User
3. SOURCE
Pattern
PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
01/02/03/04/User
Projection (Projector Position)/3D Sync/Lamp
Mode/DCR/Closed Caption/Auto Off (Auto Power
Off)/Message/Screen Color/Screen Capture
My Button
Language
(PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws only)/Information
Multi-language OSD
selection
Front Table/Rear Table/
Projector Position
Auto Power Off
Rear Ceiling/Front Ceiling
Disable/5 min/10 min/20
min/30 min/40 min/50 min/
60 min
4.
Disable/5 min/10 min/15
Blank Timer
SYSTEM
SETUP:
Basic
min/20 min/25 min/30 min
Panel Key Lock
On/Off
Black/Blue/ViewSonic/
Screen Capture (PJD6223/
PJD6253/PJD6353/PJD6353s/
PJD6383/PJD6383s/PJD6653w/
PJD6553w/PJD6653ws/PJD6683w
Splash Screen
PJD6683ws only)
Off
Screen Capture (PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws only)
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Main menu
Sub-menu
DHCP
Options
Message
LAN Control
Settings
On/Off
On/Off
Projector IP Address
Subnet Mask
Default Gateway
DNS Server
(PJD6223/PJD6253/
PJD6353/PJD6353s/
PJD6383/PJD6383s/
PJD6553w/
4.
PJD6653w/
PJD6653ws/
PJD6683w
SYSTEM
SETUP:
Basic
Apply
PJD6683ws only)
Power Saving
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
On/Off
Active VGA Out
Active Audio Out
Quick Power Off
Standby
Settings
High Altitude Mode
DCR
Mute
Volume
Audio Settings
5 sec/10 sec/15 sec/20 sec/
25 sec/30 sec
Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right
Menu Display Time
Menu Settings
Menu Position
Closed Caption
Enable
Caption Version
Lamp Mode
Reset Lamp Timer
Equivalent Lamp
Hour
On/Off
Closed Caption
Lamp Settings
CC1/CC2/CC3/CC4
Normal/Economic
5.
SYSTEM
SETUP:
Advanced
Timer Period
Timer Display
1~240 minutes
Always/1 min/2 min/3 min/
Never
Top-Left/Bottom-Left/Top-
Right/Bottom-Right
Timer Position
Presentation
Timer
Timer Counting
Direction
Count Down/Count Up
Sound Reminder
Start Counting/Off
Change Password
Power On Lock
On/Off
Security
Settings
On/Off
A/B
On/Off
Remote Control Code
Reset All Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
48
Main menu
Sub-menu
Options
•
•
•
•
•
•
Source
Color Mode
Resolution
Color System
Equivalent Lamp Hour
MAC Address (PJD6223/PJD6253/
6.
INFORMATION
Current System Status
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6553w/PJD6653w/PJD6653ws/
PJD6683w/PJD6683ws only)
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Description of each menu
Function
Description
Corrects the projected picture’s color when the projection surface
is not white. See "Using Screen Color" on page 33 for details.
There are three options to set the image's aspect ratio depending
on your input signal source. See "Selecting the aspect ratio" on
page 30 for details.
Screen Color
Aspect Ratio
Keystone
Corrects any keystoning of the image. See "Correcting keystone"
on page 29 for details.
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.
Adjusts the clock phase to reduce image
distortion.
Position
Phase
Adjusts the horizontal width of the image.
H. Size
Zoom
Magnifies or reduces the projected image. See "Magnifying and
searching for details" on page 29 for details.
This projector features a 3D function which enables you to enjoy
the 3D movies, videos, and sporting events in a more realistic
way by presenting the depth of the images.
This function is not available when video source is detected
for the PJD5126/PJD5226/PJD5226w.
You need to wear a pair of 3D glasses to view the 3D images.
•
TI 3D DLP Link:
Enables projector for TI 3D DLP Link.
3D Sync
•
Off:
Disables 3D.
When the 3D Sync function is on:
•
•
•
•
The brightness level of the projected image will decrease.
The Color Mode cannot be adjusted.
The Keystone can only be adjusted within limited degrees.
The Zoom can only magnify the pictures to limited sizes.
3D Sync
Invert
When you discover the inversion of the image depth, enable this
function to correct the problem. (For TI 3D DLP Link only)
Color
Management
See "Color Management" on page 35 for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
50
Function
Description
Pre-defined picture modes are provided so you can optimize your
projector image set-up to suit your program type. See "Selecting a
picture mode" on page 32 for details.
Color Mode
Selects a picture mode that most suits your need for the image
quality and further fine-tune the image based on the selections
listed on the same page below. See "Setting the User 1/User 2
mode" on page 33 for details.
Reference
Mode
Adjusts the brightness of the image. See "Adjusting Brightness" on
page 34 for details.
Adjusts the degree of difference between dark and light in the
image. See "Adjusting Contrast" on page 34 for details.
Adjusts the color saturation level -- the amount of each color in a
video image. See "Adjusting Color" on page 34 for details.
Brightness
Contrast
Color
Adjusts the red and green color tones of the image. See "Adjusting
Tint" on page 34 for details.
Tint
The function is only available when Video or S-Video with
NTSC system is selected.
Adjusts the image to make it look sharper or softer. See "Adjusting
Sharpness" on page 34 for details.
Sharpness
Brilliant
Color
Adjusts white peaking while maintaining correct color presentation.
See "Adjusting Brilliant Color" on page 34 for details.
Color
Temperature
See "Selecting a Color Temperature" on page 34 for details.
Save
Settings
Saves the settings made for the User 1 or User 2 mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Function
Description
Quick Auto
Search
See "Switching input signal" on page 27 for details.
Color Space
Conversion
See "Changing Color Space" on page 27 for details.
Allows the projector to decrease the power consumption
automatically if no input signal is detected after a set period of time.
DynamicEco
Timer
It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes.
Selecting On enables you to restart the projector immediately
within 150 seconds after turning it off. After 150 seconds, if the
projector is not turned on again, it will directly enter the standby
mode.
Smart
Restart
•It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes.
If the projector is resumed by using the Smart Restart
feature, this function can be executed immediately.
•When On is selected, the Quick Power Off function will be
automatically set to “On”.
The projector can display several test patterns. It helps you adjust
the image size and focus and check that the!projected image is free
from distortion.
Pattern
Selecting User displays the picture you saved as Screen
Capture.
Sets a hotkey on remote control.
My Button
Download from Www.Somanuals.com. All Manuals Search And Download.
52
Function
Description
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 23 for details.
Language
The projector can be installed on a ceiling or behind a screen, or
with one or more mirrors. See "Choosing a location" on page 12
for details.
Projector
Position
Allows the projector to turn off automatically if no input signal
is detected after a set period of time. See "Setting Auto Power
Off" on page 57 for details.
Auto Power
Off
Sets the image blank time when the Blank feature is activated,
once elapsed the image will return to the screen. See "Hiding the
image" on page 37 for details.
Blank Timer
I
Disables or enables all panel key functions except POWER
Panel Key
Lock
on the projector and keys on the remote control. See "Locking
control keys" on page 37 for details.
Splash
Screen
Allows you to select which logo screen will be displayed during
projector start-up.
Screen
Capture
Captures and stores the projected picture as Screen Capture.
See "Creating your own startup screen" on page 38 for details.
Selecting On displays the current information on the screen
Message
when the projector is detecting or searching for a signal.
LAN Control
Settings
See "Controlling the projector through a LAN environment" on
page 39 for details.
Standby
Settings
See "Using the projector in standby mode" on page 45 for
details.
High Altitude
Mode
A mode for operation in high altitude areas. See "Operating in a
high altitude environment" on page 37 for details.
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and
economic modes according to the input image detected.
DCR
This function is only available when a PC source is in use.
After enabling DCR, frequent lamp mode switching may
shorten lamp life and noise level will vary during operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Function
Description
The sound adjustments made as below will have an effect on the
projector speaker. Be sure you have made a correct connection to
the projector audio input/output jacks. See "Connection" on page
17 for more details.
Mute
Audio
Settings
Mutes the sound received from AUDIO IN 1 and AUDIO IN 2
(L/R).
Volume
Adjusts the sound level received from AUDIO IN 1 and AUDIO
IN 2 (L/R).
Menu Display Time
Sets the length of time the OSD will remain active after your last
key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu
Settings
Menu Position
Sets the On-Screen Display (OSD) menu position.
Closed Caption Enable
Activates the function by selecting On when the selected input
signal carries closed captions.
•
Captions: An on-screen display of the dialogue, narration,
and sound effects of TV programs and videos that are closed
captioned (usually marked as "CC" in TV listings).
Closed
Caption
This function is only available when a Composite video or
S-Video input signal is selected and its system format is
NTSC.
Caption Version
Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the
primary language in your area).
Lamp Mode
See "Setting Lamp Mode as Economic" on page 57 for details.
Reset Lamp Timer
Lamp
Settings
See "Resetting the lamp timer" on page 61 for details.
Equivalent Lamp Hour
See "Getting to know the lamp hour" on page 57 for details on
how the total lamp hour is calculated.
Reminds the presenter to finish the presentation within a certain
time frame. See "Setting the presentation timer" on page 36 for
details.
Presentation
Timer
Download from Www.Somanuals.com. All Manuals Search And Download.
54
Function
Description
Security
Settings
See "Utilizing the password function" on page 24 for details.
Remote
Control Code
See "Remote control code" on page 9 for details.
Returns all settings to the factory preset values.
Reset All
Settings
The following settings will still remain: Phase, H. Size, User
1, User 2, Language, Projector Position, High Altitude
Mode, Security Settings.
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the PICTURE menu.
Resolution
Shows the native resolution of the input signal.
Current
System
Status
Color System
Shows input system format, NTSC, PAL, SECAM, or RGB.
Equivalent Lamp Hour
Displays the number of hours the lamp has been used.
MAC Address
Shows the MAC Address of your projector.
MAC Address stands for Media Access Control Address,
which is a physical layer address used to uniquely identify
a network node.
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Maintenance
Care of the projector
Your projector needs little maintenance. The only thing you need to do on a regular basis is
to keep the lens clean.
Never remove any parts of the projector except the lamp. Contact your dealer if other parts
need replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
•
•
Use a canister of compressed air to remove dust.
If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 45 and unplug the power cord.
•
•
To remove dirt or dust, wipe the case with a soft, lint-free cloth.
To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the
case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
•
Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specifications" on page 64 or
consult your dealer about the range.
•
•
•
Retract the adjuster feet.
Remove the battery from the remote control.
Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
Download from Www.Somanuals.com. All Manuals Search And Download.
56
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
1.
Press MENU/EXIT on the projector or Menu on the remote control and then press
/
until the SYSTEM SETUP: Advanced menu is highlighted.
2.
Press to highlight Lamp Settings and press MODE/ENTER on the projector or
ENTER on the remote control. The Lamp Settings page is displayed.
You will see the Equivalent lamp hour information on the menu.
To leave the menu, press MENU/EXIT on the projector or Exit on the remote
control.
3.
4.
You can also get the lamp hour information on the INFORMATION menu.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode as Economic
Using Economic mode reduces system noise and power consumption by 20%. If the
Economic mode is selected, the light output will be reduced and result in darker projected
pictures.
Setting the projector in Economic mode also extends the lamp operation life. To set
Economic mode, go into the SYSTEM SETUP: Advanced > Lamp Settings > Lamp
Mode menu and press
/
.
Setting Auto Power Off
This function allows the projector to turn off automatically if no input source is detected
after a set period of time to prevent unnecessary waste of lamp life.
To set Auto Power Off, go into the SYSTEM SETUP: Basic > Auto Power Off menu and
press
/
. If the preset time lengths are not suitable for your presentation, select Disable.
The projector will not automatically shut down in a certain time period.
Download from Www.Somanuals.com. All Manuals Search And Download.
57
Timing of replacing the lamp
When the Lamp indicator lights up red or a message appears suggesting it is time to
replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a
malfunction in the projector and in some instances the lamp may explode.
CAUTION
The Lamp indicator light and Temperature warning light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp or Temp indicator
still lights up after turning the power back on, please contact your dealer. See "Indicators" on
page 62 for details.
The following lamp warning displays will remind you to change the lamp.
Status
Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
(See "Setting Lamp Mode as Economic" on page
57), you may continue to operate the projector
until the next hour lamp warning appears.
Notice
Order Replacement Lamp
Lamp > ____ Hours
OK
A new lamp should be fitted to avoid the
inconvenience when the projector runs out of lamp
time.
Notice
Replace Lamp Soon
Lamp > ____ Hours
OK
It is strongly recommended that you replace the
lamp at this age. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished. If the lamp is not
replaced beforehand, it must be replaced when
you see this message.
Notice
Replace Lamp Now
Lamp > ____ Hours
Lamp usage time exceeded
OK
The lamp MUST be replaced before the projector
will operate normally.
Notice
Lamp usage time exceeded
Replace lamp (refer to User Manual)
Then reset lamp timer
OK
Download from Www.Somanuals.com. All Manuals Search And Download.
58
Replacing the lamp
To prepare a new lamp, contact your dealer and tell the lamp type number.
RLC-070 ņPJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws
RLC-071 ņPJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws
Type number:
Type number:
Type number:
Ň
Ň
RLC-077 ņPJD5126/PJD5226
Ň
WARNING
Hg - Lamp contains mercury. Manage in accordance with local disposal
•
•
•
To reduce the risk of electrical shock, always turn the projector off and disconnect the
power cord before changing the lamp.
To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes
before replacing the lamp.
To reduce the risk of injuries to fingers and damage to internal components, use caution
when removing lamp glass that has shattered into sharp pieces. Before replacing the
lamp, clean the lamp compartment and dispose of cleaning materials. Be careful of sharp
edges in the lamp compartment. Wash hands after lamp replacement.
•
Only ViewSonic certified lamps are tested with this projector. Use of other lamps may
cause electrical shock and fire.
1.
Turn the power off and disconnect the
projector from the wall socket. If the
lamp is hot, avoid burns by waiting for
approximately 45 minutes until the
lamp has cooled.
2.
3.
Loosen the screws that secure the lamp
cover on the both sides of the projector
until the lamp cover loosens.
Remove the lamp cover from the
projector.
1
WARNING
•
•
Do not turn the power on with the lamp
2
cover removed.
Do not insert your fingers between the
lamp and the projector. The sharp edges
inside the projector may cause injuries.
4.
Remove and dispose of the lamp
protection film.
Download from Www.Somanuals.com. All Manuals Search And Download.
59
5.
6.
Loosen the screw that secures the lamp.
Lift the handle so that it stands up. Use
the handle to slowly pull the lamp out
of the projector.
CAUTION
•
•
•
Pulling it too quickly may cause the lamp
to break and scatter broken glass in the
projector.
Do not place the lamp in locations where
water might splash on it, children can
reach it, or near flammable materials.
Do not insert your hands into the projector
after the lamp is removed. If you touch the
optical components inside, it could cause
color unevenness and distortion of the
projected images.
7.
Insert the new lamp into the lamp
compartment and make sure it fits in
the projector.
8.
Tighten the screw that secures the lamp.
CAUTION
•
Loose screw may cause a bad connection,
which could result in malfunction.
•
Do not over tighten the screw.
9.
Ensure the handle is fully laid flat and
locked in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
60
10. Place the lamp protection film supplied
with the new lamp on the lamp
compartment.
2
11. Replace the lamp cover on the
projector.
1
12. Tighten the screws that secure the lamp
cover.
CAUTION
•
•
Loose screw may cause a bad connection,
which could result in malfunction.
Do not over tighten the screws.
13. Restart the projector.
CAUTION
Do not turn the power on with the lamp cover removed.
Resetting the lamp timer
14. After the startup logo, open the On-Screen
Display (OSD) menu.
15. Go to the SYSTEM SETUP: Advanced >
Lamp Settings menu. Press MODE/ENTER
on the projector or ENTER on the remote
control. The Lamp Settings page is
displayed.
Notice
Reset Lamp Timer?
Cancel
Reset
16. Press to highlight Reset lamp timer and
press MODE/ENTER on the projector or
ENTER on the remote control. A warning
message is displayed asking if you want to
reset the lamp timer.
17. Highlight Reset and press MODE/ENTER
on the projector or ENTER on the remote
control. The lamp time will be reset to '0'.
CAUTION
Do not reset if the lamp is not new or replaced as this
could cause damage.
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Indicators
Light
Status & Description
Power Temp Lamp
Power events
Blue
Flashing
Blue
Off
Off
Stand-by mode
Powering up
Normal operation
Off
Off
Off
Off
Blue
Lamp events
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Purple
Off
Off
Red
Red
Flashing
1.
2.
The projector needs 90 seconds to cool down. Or
Please contact your dealer for assistance.
Off
Thermal events
Off
Off
Off
Red
Red
Blue
Blue
Purple
Purple
Off
Red
Red
Red
Red
Red
Red
Red
Red
Red
Green
Off
Red
Green
Red
Green
Red
Green
Red
The projector has shut down automatically. If you try to re-
start the projector, it will shut down again. Please contact
your dealer for assistance.
Green
Red
Download from Www.Somanuals.com. All Manuals Search And Download.
62
Troubleshooting
The projector does not turn on.
Cause
Remedy
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the
power outlet. If the power outlet has a switch,
make sure that it is switched on.
There is no power from the power
cord.
Attempting to turn the projector on
again during the cooling process.
Wait until the cooling down process has
completed.
No picture
Cause
Remedy
The video source is not turned on or
connected correctly.
Turn the video source on and check that the
signal cable is connected correctly.
The projector is not correctly
connected to the input signal device.
Check the connection.
Select the correct input signal with the
SOURCE key on the projector or remote
control.
The input signal has not been
correctly selected.
The lens cover is still closed.
Blurred image
Cause
Open the lens cover.
Remedy
The projection lens is not correctly
focused.
Adjust the focus of the lens using the focus
ring.
The projector and the screen are not
aligned properly.
Adjust the projection angle and direction as
well as the height of the projector if necessary.
The lens cover is still closed.
Open the lens cover.
Remote control does not work
Cause
Remedy
The battery is out of power.
Replace the battery with a new one.
There is an obstacle between the
remote control and the projector.
Remove the obstacle.
You are too far away from the
projector.
Stand within 8 meters (26 feet) of the
projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Specifications
Projector specifications
• All specifications are subject to change without notice.
Not all models can be purchased in your region.
•
General
Product name
DLP Projector
Optical
Resolution
PJD5126:
800 x 600 SVGA
PJD5226/PJD6223/PJD6253/PJD6353/PJD6353s/PJD: 6383/PJD6383s:
1024 x 768 XGA
PJD5226w/PJD6553w/PJD6653w/PJD6653ws/PJD6683w/PJD6383ws:
1280 x 800 WXGA
Display system
Lamp
1-CHIP DMD
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/ PJD6653w/PJD6653ws:
180 W lamp
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
240 W lamp
Electrical
Power supply
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws:
AC100–240V, 2.9 A, 50/60 Hz (Automatic)
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
AC100–240V, 3.5 A, 50/60 Hz (Automatic)
Power
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6353/PJD6353s/PJD6653w/PJD6653ws:
consumption
285 W (Max); < 1 W (Standby)
PJD6253/PJD6383/PJD6383s/PJD6553w/PJD6683w/PJD6683ws:
350 W (Max); < 1 W (Standby)
Mechanical
Weight
PJD5126/PJD5226/PJD5226w/PJD6223/PJD6253/PJD6553w:
2.6 Kg (5.74 lbs)
PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
2.99 Kg (6.6 lbs)
Download from Www.Somanuals.com. All Manuals Search And Download.
64
Input terminal
Computer input
RGB input
D-Sub 15-pin (female) x 2
Video signal input
S-VIDEO
Mini DIN 4-pin port x 1
RCA jack x 1
VIDEO
SD/HDTV signal
input
Analog – D-Sub <–> Component RCA jack x 3
(through RGB input)
Digital – PJD5126/PJD5226/PJD5226w:
N/A
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
HDMI V1.3 x 1
Audio signal input PC audio jack x 1 PC audio jack x 2
Output terminal
RGB output
Speaker
D-Sub 15-pin (female) x 1
PJD5126/PJD5226/PJD5226w:
2 watt x 1
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
10 watt x 1
Control terminal
RS-232 serial
9 pin x 1
control
LAN
PJD5126/PJD5226/PJD5226w:
N/A
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
RJ45 x 1
USB serial control Type mini B
IR receiver
PJD5126/PJD5226/PJD5226w:
x 1 (Front)
PJD6223/PJD6253/PJD6353/PJD6353s/PJD6383/PJD6383s/PJD6553w/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws:
x 2!(Front and Top)
Environmental Requirements
Operating
0°C–40°C at sea level
temperature
Operating relative 10%–90% (without condensation)
humidity
Operating altitude
•
•
0–1499 m at 0°C–35°C
1500–3000 m at 0°C–30°C (with High Altitude Mode on)
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Dimensions
294 mm (W) x 84 mm (H) x 242 mm (D) (Excluding extrusions)
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6253/PJD6553w
294
242
M
E
N
U
E
X
I
T
84
PJD6353/PJD6353s/PJD6383/PJD6383s/
PJD6653w/PJD6653ws/PJD6683w/PJD6683ws
294
242
M
E
N
U
E
X
I
T
84
Ceiling mount installation
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
160
137
Unit: mm
Download from Www.Somanuals.com. All Manuals Search And Download.
66
Timing chart
Supported timing for PC input
Horizontal!
Frequency
(kHz)
31.469
31.469
37.861
37.5
Vertical!
Frequency
(Hz)
70.087
59.94
72.809
75
Pixel!
Frequency
(MHz)
28.3221
25.175
31.5
Resolution
Mode
720 x 400
720 x 400_70
VGA_60
VGA_72
640 x 480
31.5
VGA_75
43.269
61.91
85.008
119.518
60.317
72.188
75
85.061
49.916
119.854
60.004
70.069
75.029
84.997
49.98
119.804
59.81
74.934
84.88
60.020
75.025
85.024
60
59.978
60
36
52.5
40
50
VGA_85
VGA_120
SVGA_60
SVGA_72
SVGA_75
SVGA_85
SVGA_50
SVGA_120
XGA_60
XGA_70
XGA_75
XGA_85
XGA_50
XGA_120
WXGA_60
WXGA_75
WXGA_85
SXGA_60
SXGA_75
SXGA_85
1280 x 960_60
SXGA+_60
UXGA
37.879
48.077
46.875
53.674
30.998
77.425
48.363
56.476
60.023
68.667
39.634
98.958
49.702
62.795
71.554
63.981
79.976
91.146
60
49.5
800 x 600
56.25
30.75
83
65
75
78.75
94.5
52
137.75
83.5
106.5
122.5
108.000
135.000
157.500
108
1024 x 768
1280 x 800
1280 x 1024
1280 x 960
1400 x 1050
1600 x 1200
65.317
75
121.75
162
640 x 480@67Hz
832 x 624@75Hz
1024 x 768@75Hz
1152 x 870@75Hz
35
66.667
74.546
75.02
30.24
57.28
80
MAC13
MAC16
MAC19
MAC21
49.722
60.241
68.68
75.06
100
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Supported timing for Component-YPbPr input
Horizontal Frequency
Signal Format
Vertical Frequency (Hz)
(kHz)
15.73
31.47
15.63
31.25
45.00
37.50
33.75
28.13
67.5
480i(525i)@60Hz
480p(525p)@60Hz
576i(625i)@50Hz
576p(625p)@50Hz
720p(750p)@60Hz
720p(750p)@50Hz
1080i(1125i)@60Hz
1080i(1125i)@50Hz
1080P@60Hz
59.94
59.94
50.00
50.00
60.00
50.00
60.00
50.00
60
1080P@50Hz
56.26
50
Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image
vibration.
Supported timing for Video and S-Video inputs
Horizontal
Frequency (kHz)
15.73
Vertical Frequency
Color sub-carrier
Video mode
(Hz)
60
50
Frequency (MHz)
NTSC
PAL
3.58
4.43
15.63
SECAM
PAL-M
PAL-N
15.63
15.73
15.63
50
60
50
4.25 or 4.41
3.58
3.58
PAL-60
NTSC4.43
15.73
15.73
60
60
4.43
4.43
Download from Www.Somanuals.com. All Manuals Search And Download.
68
Copyright information
Copyright
Copyright 2011. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
Download from Www.Somanuals.com. All Manuals Search And Download.
69
Appendix
IR control table
Code A
Key
Power
Format Byte1 Byte2 Byte3 Byte4
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
83
83
83
83
83
83
83
83
83
83
83
83
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
17
03
0b
0c
0e
0f
E8
fc
f4
Freeze
Up / KeyS +
Down / KeyS -
Left
f3
f1
f0
Right
Color Mode
Mute
Auto Sync
Source
Blank
Menu
10
14
08
04
07
30
ef
EB
f7
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6253/PJD6383/PJD6383s/
3w/PJD6683w
PJ 655
D
fb
f8
CF
PJD6683ws
Enter / Mouse L
key
NEC
83
F4
15
ea
Exit
NEC
NEC
NEC
83
83
83
F4
F4
F4
28
41
45
D7
be
ba
VGA 1
VGA 2
Video/Mouse R
key
NEC
83
F4
52
ad
Mouse
Timer
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
83
83
83
83
83
83
83
83
83
83
83
83
83
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
31
27
13
32
2B
55
56
57
82
83
06
05
97
CE
d8
Aspect
Magnify
DynamicEco™
Pattern
My Button
Panel Key Lock
Volume +
Volume -
PgUp
EC
CD
D4
AA
A9
A8
7D
7C
F9
FA
68
PgDn
Info
Download from Www.Somanuals.com. All Manuals Search And Download.
70
Code B
Key
Format Byte1 Byte2 Byte3 Byte4
Power
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
83
83
83
83
83
83
83
83
83
83
83
83
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
60
61
67
68
69
6A
9E
9D
63
7D
62
6C
9F
6E
98
97
96
95
61
62
9C
82
9D
93
Freeze
Up / KeyS +
Down / KeyS -
Left
Right
Color Mode
Mute
Auto Sync
Source
Blank
Menu
PJD5126/PJD5226/PJD5226w/
PJD6223/PJD6353/PJD6353s
PJD6653w/PJD6653ws
PJD6253/PJD6383/PJD6383s/
3w/PJD6683w
PJ 655
D
PJD6683ws
Enter / Mouse L
key
NEC
83
F4
6B
94
Exit
NEC
NEC
NEC
83
83
83
F4
F4
F4
6E
64
65
91
9B
9A
VGA 1
VGA 2
Video/Mouse R
key
NEC
83
F4
66
99
Mouse
Timer
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
NEC
83
83
83
83
83
83
83
83
83
83
83
83
83
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
F4
9B
9C
9A
99
7F
7E
6D
5E
5A
5B
5D
5C
5F
64
63
65
66
80
81
92
A1
A5
A4
A2
A3
A0
Aspect
Magnify
DynamicEco™
Pattern
My Button
Panel Key Lock
Volume +
Volume -
PgUp
PgDn
Info
Download from Www.Somanuals.com. All Manuals Search And Download.
71
RJ45 response table
Status
Response
Normal => ACK
Response Code
0x03 0x14 0x00 0x00 0x00 0x14
0x00 0x14 0x00 0x00 0x00 0x14
N/A
Write
Incorrect => ERROR ACK
Timeout (>100ms)
Status
Response Code
BYTE0 BYTE1 BYTE2 BYTE3 BYTE4 BYTE5 BYTE6 BYTE7~N BYTE N+1
0x05 0x14 0x00 LSB MSB 0x00 0x00 Data Checksum
Ex1. Read power status: 0x05 0x14 0x00 0x03 0x00 0x00 0x00 0x01 0x18 = On
Read
Ex2. Read brightness: 0x05 0x14 0x00 0x04 0x00 0x00 0x00 0x32 0x00 0x4A = 50
Ex3. Read lamp hours: 0x05 0x14 0x00 0x06 0x00 0x00 0x00 0x28 0x00
0x00 0x00 0x42
= 40
•
•
The RJ45 commands can only be received via TCP port 4661.
Please refer to the below RS232 command table for the commands.
RS232 command table
<Pin assignment for this two end>
Pin
1
Description
NC
Pin
2
Description
RX
3
TX
4
NC
5
GND
RTSZ
NC
6
NC
7
8
CTSZ
9
<Interface>
RS-232 protocol
115200 bps (default)
Baud Rate
Data Length
Parity Check
Stop Bit
8 bit
None
1 bit
Flow Control
None
<RS232/RJ45 command table>
Function
Status
Action
Turn on
Turn off
cmd
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E
Write
Power
Power status
(on/off)
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00
0x5E
Read
Download from Www.Somanuals.com. All Manuals Search And Download.
72
Reset
Execute
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67
Splash
Screen Black
Splash
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x01 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x02 0x69
Screen Blue
Splash
Screen
ViewSonic
Write
Splash
Screen
Splash
Screen
Screen
Capture
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x03 0x6A
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x04 0x6B
Splash
Screen Off
Splash
Screen
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0A
0x68
Read
Quick Power
Off Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x00 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0B 0x01 0x69
Write
Read
Write
Read
Write
Quick
Power Off
Quick Power
Off On
Quick Power
Off status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0B
0x69
High Altitude
Mode Off
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x00 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0C 0x01 0x6A
High
Altitude
Mode
High Altitude
Mode On
High Altitude
Mode status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x0C
0x6A
Lamp Mode
Normal
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x00 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x10 0x01 0x6E
Lamp Mode
Economic
Lamp Mode
Message
Lamp Mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x10
0x6E
Read
Write
Read
Message Off
Message On
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84
0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85
Message
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27
0x85
Download from Www.Somanuals.com. All Manuals Search And Download.
73
Front Table
Rear Table
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61
Write
Rear Ceiling
Front Ceiling
Projector
Position
projector
position
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00
0x5F
Read
Write
OFF
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F
TI 3D DLP
Link
3D Sync
3D Sync
Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x20
0x7F
Read
Write
Read
Off
On
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x00 0x7F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x21 0x01 0x80
3D Sync
Invert
3D Sync
Invert Status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x21
0x80
Contrast
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61
Write
Read
Write
Read
Contrast
increase
Contrast
Contrast
ratio
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02
0x61
Brightness
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62
Brightness
increase
Brightness
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03
0x62
Brightness
Aspect ratio
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66
Aspect ratio
4:3
Write
Aspect ratio
16:9
Aspect ratio
Auto Adjust
Aspect ratio
16:10
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04
0x63
Read
Aspect ratio
Excute
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x05 0x00 0x63
Download from Www.Somanuals.com. All Manuals Search And Download.
74
Horizontal
position shift
right
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64
Write
Read
Write
Read
Horizontal
position
Horizontal
position shift
left
Horizontal
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06
0x65
Vertical
position shift
up
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66
Vertical
position
Vertical
position shift
down
read Vertical
position
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07
0x66
color
temperature
T1
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69
color
temperature
T2
Write
color
temperature
T3
Color
temperature
color
temperature
T4
color
temperature
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08
0x67
Read
Blank on
Blank off
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67
Write
Read
Write
Read
Blank
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09
0x68
Blank status
Decrease
Increase
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69
Keystone-
Vertical
Keystone
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A
0x69
Download from Www.Somanuals.com. All Manuals Search And Download.
75
Brightest
Movie
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x06 0x6F
User 1
User 2
Write
PC / Gaming
ViewMatch
Dynamic PC
Color mode
Dynamic
Movie
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x07 0x70
Preset mode
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B
0x6A
Read
Primarycolor
R
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x00 0x6E
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x01 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x02 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x03 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x04 0x72
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x10 0x05 0x73
Primarycolor
G
Primarycolor
B
Write
Primary
Color
Primarycolor
C
Primarycolor
M
Primarycolor
Y
Primarycolor
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x10
0x6F
Read
Write
Read
Hue
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x00 0x6F
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x11 0x01 0x70
Hue
Hue increase
Hue
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x11
0x70
Saturation
decrease
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71
Write
Read
Saturation
increase
Saturation
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12
0x71
Saturation
Download from Www.Somanuals.com. All Manuals Search And Download.
76
Gain
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71
0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72
decrease
Write
Gain
increase
Gain
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13
0x72
Read
Write
Read
Gain
Freeze on
Freeze off
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F
Freeze
Freeze
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00
0x60
Input source
VGA
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63
Input source
VGA2
Input source
Composite
Write
Source
input
Input source
SVIDEO
Input source
HDMI
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01
0x61
Read
Write
Source
Quick Auto
Search on
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62
0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61
Quick Auto
Search off
Quick Auto
Search
Quick Auto
Search
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02
0x62
Read
Mute on
Mute off
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60
Write
Read
Mute
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00
0x61
Mute status
Increse
Volume
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61
0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62
Write
Read
Decrese
Volume
Volume
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03
0x64
Volume
Download from Www.Somanuals.com. All Manuals Search And Download.
77
Reset Lamp
usuage hour
Write
Read
Read
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62
Lamp Time
Error status
Lamp
usuage hour
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01
0x63
Read error
status
0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x0C 0x0D
0x66
Download from Www.Somanuals.com. All Manuals Search And Download.
78
Customer Support
For technical support or product service, see the table below or contact your reseller.
Note : You will need the product serial number.
T=Telephone
Country/Region
Web Site
E-mail
F=Fax
ꢀꢍꢎꢏꢐꢑꢒꢒꢌꢑꢑꢒꢌꢑꢐꢑ
ꢉꢓꢏꢒꢑꢒꢒꢌꢒꢒꢑꢌꢑꢔꢔ
ꢕꢌꢖꢕꢗꢆꢆꢘꢙꢄꢊꢊꢚꢏꢌꢐꢘꢑꢛꢛꢘꢜꢛꢝꢘꢜ!!$
ꢕꢌꢖꢕꢗꢆꢆꢚꢏꢌꢐꢘꢜꢔꢜꢘꢔꢝꢝꢘꢔ$ꢝꢝ
ꢙꢏꢌꢐꢘ=ꢒ=ꢘꢜꢛꢑꢘꢝ!$!
ꢀꢁꢂꢃꢄꢅꢆꢇꢅꢈꢉꢊꢋꢌ
Zealand
Canada
com
?ꢁꢄꢗ[ꢊ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`ꢊꢁꢄꢗ[ꢊ\`ꢗ{ꢈꢁ|ꢈꢂꢁ[[ꢗꢄꢃꢈ`ꢅꢆꢆꢘ}ꢊꢂ|ꢈ
Hong Kong
India
ꢕꢏꢌꢑ$ꢔꢌꢝꢐꢒꢔꢌꢔ=ꢒꢒ
ꢕꢏꢌꢐꢑꢒꢒꢌꢔꢛꢛꢌꢒꢐꢒꢐ
`ꢗ{ꢈꢁ|ꢈ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`ꢊꢁꢄꢗ[ꢊ\`ꢗ{ꢈꢁ|ꢈꢂꢁ[ꢘ
[ꢗꢄꢃꢈ`ꢅꢆꢆꢘ}ꢊꢂ|ꢈ
service_ie@viewsoniꢘ
ceurope.com
ꢄꢊꢆꢅ^}ꢌꢖ?ꢇꢄꢊꢚ
Korea
ꢕꢏꢌꢒꢑꢒꢌꢝꢝꢝꢌꢔꢐꢝꢐ
ꢅꢃꢇ^ꢌꢀ{ꢊꢄꢇ`ꢅꢌ
ꢖꢀꢄ‚ꢊ^ꢃꢇ^ꢅꢚ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈ
ꢕꢏꢌꢒꢑꢒꢒꢘꢜꢜꢜꢐꢐꢑ$
ꢅꢃꢇ^ꢌꢀ{ꢊꢄꢇ`ꢅꢌ
(Chile)
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈ
ꢕꢏꢐꢔꢝꢒꢘꢒꢔꢒꢘ!=!$
ꢕꢏꢌꢒꢐꢑꢒꢒꢘ=ꢘꢐ$!ꢔꢝ$
ꢕꢏꢌꢒꢒꢐꢘꢑꢑꢑꢔꢝꢔꢑ!ꢔꢔ
ꢅꢃꢇ^ꢌꢀ{ꢊꢄꢇ`ꢅꢌ
(Columbia)
ꢅꢃꢇ^ꢌꢀ{ꢊꢄꢇ`ꢅꢌ
ꢖƒꢊ„ꢇ`ꢗꢚ
†ꢊ^ꢃꢅꢌ‡ꢌˆꢅꢃꢗꢂ‰ꢌꢔ=ꢌꢎꢍ†ꢌ!ꢔꢐ‰ꢌŠ‹\ꢌꢀꢌŒꢀꢓ‰ꢌ!ꢔꢐꢛꢒꢌŒꢍ?ꢀ‰ꢌŒꢍ?\ꢌꢕꢊꢆ‘ꢌꢒꢐ\ꢔꢔꢔ\ꢑ=ꢐ\$$\!!ꢌŠ‹ꢉꢌꢐꢒꢌꢉ?ꢀꢎ
?ꢆꢊ`ꢃꢄꢗꢂꢊꢄ‰ꢌꢀ]ꢌ†ꢊ“ꢗꢄ{ꢅꢌꢉꢗ\ꢌꢜꢒꢝ”„ꢝ=ꢌ‡ꢌꢜꢐ‰ꢌ=!ꢒꢒꢒꢌƒꢊꢄꢇ}ꢅ‰ꢌ•ꢁ`ꢅꢃꢅ^\ꢌꢕꢊꢆ‘ꢌꢒꢐ\===\=ꢔ$\ꢐ=\ꢐꢛ
‹ꢃ–ꢊꢄꢌ[ꢆꢅ`ꢊꢂꢌ[ꢆꢊꢅꢂꢊꢌꢄꢊ“ꢊꢄꢌꢃꢗꢌ–ꢃꢃ[‘ꢈꢈꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈꢂꢗ[ꢗꢄꢃꢊꢈꢇ^}ꢊ„\–ꢃ{—ƒꢊ„ꢇ`ꢗ
ꢅꢃꢇ^ꢌꢀ{ꢊꢄꢇ`ꢅꢌꢖŒꢊꢄꢁꢚ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈ
ꢅ[\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈ{ꢊꢈ
ꢕꢏꢌꢒꢑꢒꢒꢘ$ꢜ$ꢛ$
ƒꢅ`ꢅꢁ
ꢕꢏꢌꢑ$ꢝꢌꢔꢑ!ꢒꢌꢒꢝꢒꢝ
Contact your reseller
ƒꢇ}}ꢆꢊꢌ?ꢅꢂꢃ
ꢕꢏꢌꢐꢘꢑꢒꢒꢘꢛꢑꢑꢘꢛꢛꢑꢑꢌꢖ?^‚ꢆꢇꢂ–ꢚ
ꢕꢏꢌꢐꢘꢑꢛꢛꢘꢝ!=ꢘꢐꢝꢒꢜꢌꢖꢎ[ꢅ^ꢇꢂ–ꢚ
ꢙꢏꢌꢐꢘ=ꢒ=ꢘꢜꢛꢑꢘꢝ!$!
Œꢁꢊꢄꢃꢗꢌ†ꢇ`ꢗꢌ˜ꢌ™ꢇꢄ‚ꢇ^ꢌ
Islands
ꢎꢇ^‚ꢅ[ꢗꢄꢊꢈƒꢅꢆꢅ‡ꢂꢇꢅꢈ
Thailand
ꢅ[\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈšꢅꢈ
ꢕꢏꢌꢛ$ꢌꢛꢜꢛꢐꢌꢛꢒꢜꢜ
ꢎꢗꢁꢃ–ꢌꢀ“ꢄꢇ`ꢅ
Contact your reseller
`ꢗ{ꢈꢁ|ꢈ
ꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`ꢊꢁꢄꢗ[ꢊ\`ꢗ{ꢈꢁ|ꢈꢂꢁ[ꢘ
[ꢗꢄꢃꢈ`ꢅꢆꢆꢘ}ꢊꢂ|ꢈ
service_gb@viewsoniꢘ
ceurope.com
United Kingdom
ꢕꢌꢖꢕꢗꢆꢆꢘꢙꢄꢊꢊꢚꢏꢌꢐꢘꢑꢒꢒꢘꢛꢑꢑꢘꢛꢛꢑꢑ
ꢕꢌꢖꢕꢗꢆꢆꢚꢏꢌꢐꢘꢜꢔꢜꢘꢔꢝꢝꢘꢔ$ꢝꢒ
ꢙꢏꢌꢐꢘ=ꢒ=ꢘꢜꢛꢑꢘꢝ!$!
ꢍ^ꢇꢃꢊ}ꢌꢎꢃꢅꢃꢊꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
79
Limited Warranty
®
VIEWSONIC PROJECTOR
What the warranty covers:
™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢋꢅꢄꢄꢅ^ꢃꢂꢌꢇꢃꢂꢌ[ꢄꢗ}ꢁ`ꢃꢂꢌꢃꢗꢌ›ꢊꢌ“ꢄꢊꢊꢌ“ꢄꢗ{ꢌ}ꢊ“ꢊ`ꢃꢂꢌꢇ^ꢌ{ꢅꢃꢊꢄꢇꢅꢆꢌꢅ^}ꢌꢋꢗꢄ|{ꢅ^ꢂ–ꢇ[‰ꢌꢁ^}ꢊꢄꢌ^ꢗꢄ{ꢅꢆꢌ
use, during the warranty period. If a product proves to be defective in material or workmanship during
ꢃ–ꢊꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ[ꢊꢄꢇꢗ}‰ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢋꢇꢆꢆ‰ꢌꢅꢃꢌꢇꢃꢂꢌꢂꢗꢆꢊꢌꢗ[ꢃꢇꢗ^‰ꢌꢄꢊ[ꢅꢇꢄꢌꢗꢄꢌꢄꢊ[ꢆꢅ`ꢊꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌꢋꢇꢃ–ꢌꢅꢌꢆꢇ|ꢊꢌ[ꢄꢗ}ꢁ`ꢃ\ꢌ
Replacement product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
ꢎꢁ›œꢊ`ꢃꢌꢃꢗꢌꢃ–ꢊꢌ{ꢗꢄꢊꢌꢆꢇ{ꢇꢃꢊ}ꢌꢗ^ꢊꢌꢖꢐꢚꢌ‡ꢊꢅꢄꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢂꢊꢃꢌꢗꢁꢃꢌ›ꢊꢆꢗꢋ‰ꢌꢉꢗꢄꢃ–ꢌꢅ^}ꢌꢎꢗꢁꢃ–ꢌꢀ{ꢊꢄꢇ`ꢅ‘ꢌꢕ–ꢄꢊꢊꢌꢖꢝꢚꢌ
‡ꢊꢅꢄꢂꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ“ꢗꢄꢌꢅꢆꢆꢌ[ꢅꢄꢃꢂꢌꢊ„`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢆꢅ{[‰ꢌꢃ–ꢄꢊꢊꢌꢖꢝꢚꢌ‡ꢊꢅꢄꢂꢌ“ꢗꢄꢌꢆꢅ›ꢗꢄ‰ꢌꢅ^}ꢌꢗ^ꢊꢌꢖꢐꢚꢌ‡ꢊꢅꢄꢌ“ꢗꢄꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌ
ꢆꢅ{[ꢌ“ꢄꢗ{ꢌꢃ–ꢊꢌ}ꢅꢃꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ[ꢁꢄ`–ꢅꢂꢊžꢌ?ꢁꢄꢗ[ꢊꢌꢊ„`ꢊ[ꢃꢌŒꢗꢆꢅ^}‘ꢌꢕ–ꢄꢊꢊꢌꢖꢝꢚꢌ‡ꢊꢅꢄꢂꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ“ꢗꢄꢌ
ꢅꢆꢆꢌ[ꢅꢄꢃꢂꢌꢊ„`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢆꢅ{[‰ꢌꢃ–ꢄꢊꢊꢌꢖꢝꢚꢌ‡ꢊꢅꢄꢂꢌ“ꢗꢄꢌꢆꢅ›ꢗꢄ‰ꢌꢅ^}ꢌ^ꢇ^ꢊꢃ‡ꢌꢖ=ꢒꢚꢌ}ꢅ‡ꢂꢌ“ꢗꢄꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌꢆꢅ{[ꢌ“ꢄꢗ{ꢌ
ꢃ–ꢊꢌ}ꢅꢃꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ[ꢁꢄ`–ꢅꢂꢊžꢌŒꢗꢆꢅ^}‘ꢌꢕꢋꢗꢌꢖꢔꢚꢌ‡ꢊꢅꢄꢂꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ“ꢗꢄꢌꢅꢆꢆꢌ[ꢅꢄꢃꢂꢌꢊ„`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢆꢅ{[‰ꢌ
ꢃꢋꢗꢌꢖꢔꢚꢌ‡ꢊꢅꢄꢂꢌ“ꢗꢄꢌꢆꢅ›ꢗꢄ‰ꢌꢅ^}ꢌ^ꢇ^ꢊꢃ‡ꢌꢖ=ꢒꢚꢌ}ꢅ‡ꢂꢌ“ꢗꢄꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌꢆꢅ{[ꢌ“ꢄꢗ{ꢌꢃ–ꢊꢌ}ꢅꢃꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ
purchase.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than “ꢗꢁꢄꢃꢊꢊ^ꢌꢖꢐꢜꢚꢌ–ꢗꢁꢄꢂꢌꢅ]ꢊꢄꢅ‚ꢊꢌ
}ꢅꢇꢆ‡ꢌꢁꢂꢅ‚ꢊ‰ꢌꢉꢗꢄꢃ–ꢌꢅ^}ꢌꢎꢗꢁꢃ–ꢌꢀ{ꢊꢄꢇ`ꢅ‘ꢌ‹^ꢊꢌꢖꢐꢚꢌ‡ꢊꢅꢄꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ“ꢗꢄꢌꢅꢆꢆꢌ[ꢅꢄꢃꢂꢌꢊ„`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢆꢅ{[‰ꢌꢗ^ꢊꢌꢖꢐꢚꢌ
‡ꢊꢅꢄꢌ“ꢗꢄꢌꢆꢅ›ꢗꢄ‰ꢌꢅ^}ꢌ^ꢇ^ꢊꢃ‡ꢌꢖ=ꢒꢚꢌ}ꢅ‡ꢂꢌ“ꢗꢄꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌꢆꢅ{[ꢌ“ꢄꢗ{ꢌꢃ–ꢊꢌ}ꢅꢃꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ[ꢁꢄ`–ꢅꢂꢊžꢌ
?ꢁꢄꢗ[ꢊ‘ꢌ‹^ꢊꢌꢖꢐꢚꢌ‡ꢊꢅꢄꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ“ꢗꢄꢌꢅꢆꢆꢌ[ꢅꢄꢃꢂꢌꢊ„`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢆꢅ{[‰ꢌꢗ^ꢊꢌꢖꢐꢚꢌ‡ꢊꢅꢄꢌ“ꢗꢄꢌꢆꢅ›ꢗꢄ‰ꢌꢅ^}ꢌ^ꢇ^ꢊꢃ‡ꢌꢖ=ꢒꢚꢌ
}ꢅ‡ꢂꢌ“ꢗꢄꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌꢆꢅ{[ꢌ“ꢄꢗ{ꢌꢃ–ꢊꢌ}ꢅꢃꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ[ꢁꢄ`–ꢅꢂꢊ\ꢌ
‹ꢃ–ꢊꢄꢌꢄꢊ‚ꢇꢗ^ꢂꢌꢗꢄꢌ`ꢗꢁ^ꢃꢄꢇꢊꢂ‘ꢌŒꢆꢊꢅꢂꢊꢌ`–ꢊ`|ꢌꢋꢇꢃ–ꢌ‡ꢗꢁꢄꢌꢆꢗ`ꢅꢆꢌ}ꢊꢅꢆꢊꢄꢌꢗꢄꢌꢆꢗ`ꢅꢆꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢗ“[`ꢊꢌ“ꢗꢄꢌꢃ–ꢊꢌ
warranty information.
ꢅ{[ꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢂꢁ›œꢊ`ꢃꢌꢃꢗꢌꢃꢊꢄ{ꢂꢌꢅ^}ꢌ`ꢗ^}ꢇꢃꢇꢗ^ꢂ‰ꢌ]ꢊꢄꢇ[`ꢅꢃꢇꢗ^ꢌꢅ^}ꢌꢅ[[ꢄꢗ]ꢅꢆ\ꢌꢀ[[ꢆꢇꢊꢂꢌꢃꢗꢌ{ꢅ^ꢁ“ꢅ`ꢃꢁꢄꢊꢄRꢂꢌ
ꢇ^ꢂꢃꢅꢆꢆꢊ}ꢌꢆꢅ{[ꢌꢗ^ꢆ‡\ꢌꢌꢀꢆꢆꢌꢅ``ꢊꢂꢂꢗꢄ‡ꢌꢆꢅ{[ꢂꢌ[ꢁꢄ`–ꢅꢂꢊ}ꢌꢂꢊ[ꢅꢄꢅꢃꢊꢆ‡ꢌꢅꢄꢊꢌꢋꢅꢄꢄꢅ^ꢃꢊ}ꢌ“ꢗꢄꢌ=ꢒꢌ}ꢅ‡ꢂ\
Who the warranty protects:
This warranty is valid only for the [ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ[ꢁꢄ`–ꢅꢂꢊꢄ\
What the warranty does not cover:
1.ꢌ ꢀ^‡ꢌ[ꢄꢗ}ꢁ`ꢃꢌꢗ^ꢌꢋ–ꢇ`–ꢌꢃ–ꢊꢌꢂꢊꢄꢇꢅꢆꢌ^ꢁ{›ꢊꢄꢌ–ꢅꢂꢌ›ꢊꢊ^ꢌ}ꢊ“ꢅ`ꢊ}‰ꢌ{ꢗ}ꢇ[ꢊ}ꢌꢗꢄꢌꢄꢊ{ꢗ]ꢊ}\
2.ꢌ ˆꢅ{ꢅ‚ꢊ‰ꢌ}ꢊꢃꢊꢄꢇꢗꢄꢅꢃꢇꢗ^‰ꢌ“ꢅꢇꢆꢁꢄꢊ‰ꢌꢗꢄꢌ{ꢅꢆ“ꢁ^`ꢃꢇꢗ^ꢌꢄꢊꢂꢁꢆꢃꢇ^‚ꢌ“ꢄꢗ{‘
ꢅ\ꢌ ꢌꢀ``ꢇ}ꢊ^ꢃ‰ꢌꢅ›ꢁꢂꢊ‰ꢌ{ꢇꢂꢁꢂꢊ‰ꢌ^ꢊ‚ꢆꢊ`ꢃ‰ꢌ[ꢄꢊ‰ꢌꢋꢅꢃꢊꢄ‰ꢌꢆꢇ‚–ꢃ^ꢇ^‚‰ꢌꢗꢄꢌꢗꢃ–ꢊꢄꢌꢅ`ꢃꢂꢌꢗ“ꢌ^ꢅꢃꢁꢄꢊ‰ꢌꢇ{[ꢄꢗ[ꢊꢄꢌ
{ꢅꢇ^ꢃꢊ^ꢅ^`ꢊ‰ꢌꢁ^ꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌ[ꢄꢗ}ꢁ`ꢃꢌ{ꢗ}ꢇ[`ꢅꢃꢇꢗ^‰ꢌꢗꢄꢌ“ꢅꢇꢆꢁꢄꢊꢌꢃꢗꢌ“ꢗꢆꢆꢗꢋꢌꢇ^ꢂꢃꢄꢁ`ꢃꢇꢗ^ꢂꢌꢂꢁ[[ꢆꢇꢊ}ꢌ
with the product.
ꢌ
›\ꢌ ‹[ꢊꢄꢅꢃꢇꢗ^ꢌꢗꢁꢃꢂꢇ}ꢊꢌꢗ“ꢌ[ꢄꢗ}ꢁ`ꢃꢌꢂ[ꢊ`ꢇ[`ꢅꢃꢇꢗ^ꢂ\
c. Operation of the product for other than the normal intended use or not under normal
conditions.
ꢌ
ꢌ
}\ꢌ †ꢊ[ꢅꢇꢄꢌꢗꢄꢌꢅꢃꢃꢊ{[ꢃꢊ}ꢌꢄꢊ[ꢅꢇꢄꢌ›‡ꢌꢅ^‡ꢗ^ꢊꢌ^ꢗꢃꢌꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌ›‡ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`\
ꢊ\ꢌ ꢀ^‡ꢌ}ꢅ{ꢅ‚ꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌ}ꢁꢊꢌꢃꢗꢌꢂ–ꢇ[{ꢊ^ꢃ\
f. Removal or installation of the product.
ꢌ
ꢌ
‚\ꢌ Šꢅꢁꢂꢊꢂꢌꢊ„ꢃꢊꢄ^ꢅꢆꢌꢃꢗꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ‰ꢌꢂꢁ`–ꢌꢅꢂꢌꢊꢆꢊ`ꢃꢄꢇ`ꢌ[ꢗꢋꢊꢄꢌ\ꢁ`ꢃꢁꢅꢃꢇꢗ^ꢂꢌꢗꢄꢌ“ꢅꢇꢆꢁꢄꢊ\
–\ꢌ ꢍꢂꢊꢌꢗ“ꢌꢂꢁ[[ꢆꢇꢊꢂꢌꢗꢄꢌ[ꢅꢄꢃꢂꢌ^ꢗꢃꢌ{ꢊꢊꢃꢇ^‚ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`Rꢂꢌꢂ[ꢊ`ꢇ[`ꢅꢃꢇꢗ^ꢂ\
Download from Www.Somanuals.com. All Manuals Search And Download.
80
ꢌ
ꢌ
ꢇ\ꢌ ꢉꢗꢄ{ꢅꢆꢌꢋꢊꢅꢄꢌꢅ^}ꢌꢃꢊꢅꢄ\
œ\ꢌ ꢀ^‡ꢌꢗꢃ–ꢊꢄꢌ`ꢅꢁꢂꢊꢌꢋ–ꢇ`–ꢌ}ꢗꢊꢂꢌ^ꢗꢃꢌꢄꢊꢆꢅꢃꢊꢌꢃꢗꢌꢅꢌ[ꢄꢗ}ꢁ`ꢃꢌ}ꢊ“ꢊ`ꢃ\
3. †ꢊ{ꢗ]ꢅꢆ‰ꢌꢇ^ꢂꢃꢅꢆꢆꢅꢃꢇꢗ^‰ꢌꢅ^}ꢌꢂꢊꢃꢘꢁ[ꢌꢂꢊꢄ]ꢇ`ꢊꢌ`–ꢅꢄ‚ꢊꢂ\
How to get service:
1. ꢌ ꢌꢙꢗꢄꢌꢇ^“ꢗꢄ{ꢅꢃꢇꢗ^ꢌꢅ›ꢗꢁꢃꢌꢄꢊ`ꢊꢇ]ꢇ^‚ꢌꢂꢊꢄ]ꢇ`ꢊꢌꢁ^}ꢊꢄꢌꢋꢅꢄꢄꢅ^ꢃ‡‰ꢌ`ꢗ^ꢃꢅ`ꢃꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌŠꢁꢂꢃꢗ{ꢊꢄꢌꢎꢁ[[ꢗꢄꢃꢌ
ꢖ[ꢆꢊꢅꢂꢊꢌꢄꢊ“ꢊꢄꢌꢃꢗꢌOŠꢁꢂꢃꢗ{ꢊꢄꢌꢎꢁ[[ꢗꢄꢃPꢌ[ꢅ‚ꢊꢚ\ꢌ•ꢗꢁꢌꢋꢇꢆꢆꢌ^ꢊꢊ}ꢌꢃꢗꢌ[ꢄꢗ]ꢇ}ꢊꢌ‡ꢗꢁꢄꢌ[ꢄꢗ}ꢁ`ꢃRꢂꢌꢂꢊꢄꢇꢅꢆꢌ^ꢁ{›ꢊꢄ\
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b)
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
3.ꢌꢌ ꢌꢕꢅ|ꢊꢌꢗꢄꢌꢂ–ꢇ[ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌ“ꢄꢊꢇ‚–ꢃꢌ[ꢄꢊ[ꢅꢇ}ꢌꢇ^ꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌ`ꢗ^ꢃꢅꢇ^ꢊꢄꢌꢃꢗꢌꢅ^ꢌꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢂꢊꢄ]ꢇ`ꢊꢌ
`ꢊ^ꢃꢊꢄꢌꢗꢄꢌ™ꢇꢊꢋꢎꢗ^ꢇ`\ꢌ
4.ꢌꢌ ꢌꢙꢗꢄꢌꢅ}}ꢇꢃꢇꢗ^ꢅꢆꢌꢇ^“ꢗꢄ{ꢅꢃꢇꢗ^ꢌꢗꢄꢌꢃ–ꢊꢌ^ꢅ{ꢊꢌꢗ“ꢌꢃ–ꢊꢌ^ꢊꢅꢄꢊꢂꢃꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢂꢊꢄ]ꢇ`ꢊꢌ`ꢊ^ꢃꢊꢄ‰ꢌ`ꢗ^ꢃꢅ`ꢃꢌ™ꢇꢊꢋꢎꢗ^ꢇ`\ꢌ
Limitation of implied warranties:
ꢕ–ꢊꢄꢊꢌꢅꢄꢊꢌ^ꢗꢌꢋꢅꢄꢄꢅ^ꢃꢇꢊꢂ‰ꢌꢊ„[ꢄꢊꢂꢂꢌꢗꢄꢌꢇ{[ꢆꢇꢊ}‰ꢌꢋ–ꢇ`–ꢌꢊ„ꢃꢊ^}ꢌ›ꢊ‡ꢗ^}ꢌꢃ–ꢊꢌ}ꢊꢂ`ꢄꢇ[ꢃꢇꢗ^ꢌ`ꢗ^ꢃꢅꢇ^ꢊ}ꢌ–ꢊꢄꢊꢇ^ꢌ
ꢇ^`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢇ{[ꢆꢇꢊ}ꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢗ“ꢌ{ꢊꢄ`–ꢅ^ꢃꢅ›ꢇꢆꢇꢃ‡ꢌꢅ^}ꢌ[ꢃ^ꢊꢂꢂꢌ“ꢗꢄꢌꢅꢌ[ꢅꢄꢃꢇ`ꢁꢆꢅꢄꢌ[ꢁꢄ[ꢗꢂꢊ\ꢌ
Exclusion of damages:
™ꢇꢊꢋꢎꢗ^ꢇ`Rꢂꢌꢆꢇꢅ›ꢇꢆꢇꢃ‡ꢌꢇꢂꢌꢆꢇ{ꢇꢃꢊ}ꢌꢃꢗꢌꢃ–ꢊꢌ`ꢗꢂꢃꢌꢗ“ꢌꢄꢊ[ꢅꢇꢄꢌꢗꢄꢌꢄꢊ[ꢆꢅ`ꢊ{ꢊ^ꢃꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ\ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢂ–ꢅꢆꢆꢌ^ꢗꢃꢌ
be liable for:
1.ꢌꢌ ꢌˆꢅ{ꢅ‚ꢊꢌꢃꢗꢌꢗꢃ–ꢊꢄꢌ[ꢄꢗ[ꢊꢄꢃ‡ꢌ`ꢅꢁꢂꢊ}ꢌ›‡ꢌꢅ^‡ꢌ}ꢊ“ꢊ`ꢃꢂꢌꢇ^ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ‰ꢌ}ꢅ{ꢅ‚ꢊꢂꢌ›ꢅꢂꢊ}ꢌꢁ[ꢗ^ꢌꢇ^`ꢗ^]ꢊ^ꢇꢊ^`ꢊ‰ꢌ
ꢆꢗꢂꢂꢌꢗ“ꢌꢁꢂꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌꢃꢇ{ꢊ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌ[ꢄꢗ[ꢃꢂ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌ›ꢁꢂꢇ^ꢊꢂꢂꢌꢗ[[ꢗꢄꢃꢁ^ꢇꢃ‡‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌ‚ꢗꢗ}ꢋꢇꢆꢆ‰ꢌ
interference with business relationships, or other commercial loss, even if advised of the possibility
of such damages.
2.ꢌꢌ ꢀ^‡ꢌꢗꢃ–ꢊꢄꢌ}ꢅ{ꢅ‚ꢊꢂ‰ꢌꢋ–ꢊꢃ–ꢊꢄꢌꢇ^`ꢇ}ꢊ^ꢃꢅꢆ‰ꢌ`ꢗ^ꢂꢊ£ꢁꢊ^ꢃꢇꢅꢆꢌꢗꢄꢌꢗꢃ–ꢊꢄꢋꢇꢂꢊ\ꢌ
3.ꢌꢌ ꢀ^‡ꢌ`ꢆꢅꢇ{ꢌꢅ‚ꢅꢇ^ꢂꢃꢌꢃ–ꢊꢌ`ꢁꢂꢃꢗ{ꢊꢄꢌ›‡ꢌꢅ^‡ꢌꢗꢃ–ꢊꢄꢌ[ꢅꢄꢃ‡\ꢌ
Effect of state law:
ꢕ–ꢇꢂꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ‚ꢇ]ꢊꢂꢌ‡ꢗꢁꢌꢂ[ꢊ`ꢇ[`ꢌꢆꢊ‚ꢅꢆꢌꢄꢇ‚–ꢃꢂ‰ꢌꢅ^}ꢌ‡ꢗꢁꢌ{ꢅ‡ꢌꢅꢆꢂꢗꢌ–ꢅ]ꢊꢌꢗꢃ–ꢊꢄꢌꢄꢇ‚–ꢃꢂꢌꢋ–ꢇ`–ꢌ]ꢅꢄ‡ꢌ“ꢄꢗ{ꢌꢂꢃꢅꢃꢊꢌ
ꢃꢗꢌꢂꢃꢅꢃꢊ\ꢌꢎꢗ{ꢊꢌꢂꢃꢅꢃꢊꢂꢌ}ꢗꢌ^ꢗꢃꢌꢅꢆꢆꢗꢋꢌꢆꢇ{ꢇꢃꢅꢃꢇꢗ^ꢂꢌꢗ^ꢌꢇ{[ꢆꢇꢊ}ꢌꢋꢅꢄꢄꢅ^ꢃꢇꢊꢂꢌꢅ^}ꢈꢗꢄꢌ}ꢗꢌ^ꢗꢃꢌꢅꢆꢆꢗꢋꢌꢃ–ꢊꢌꢊ„`ꢆꢁꢂꢇꢗ^ꢌꢗ“ꢌ
ꢇ^`ꢇ}ꢊ^ꢃꢅꢆꢌꢗꢄꢌ`ꢗ^ꢂꢊ£ꢁꢊ^ꢃꢇꢅꢆꢌ}ꢅ{ꢅ‚ꢊꢂ‰ꢌꢂꢗꢌꢃ–ꢊꢌꢅ›ꢗ]ꢊꢌꢆꢇ{ꢇꢃꢅꢃꢇꢗ^ꢂꢌꢅ^}ꢌꢊ„`ꢆꢁꢂꢇꢗ^ꢂꢌ{ꢅ‡ꢌ^ꢗꢃꢌꢅ[[ꢆ‡ꢌꢃꢗꢌ‡ꢗꢁ\ꢌ
Sales outside the U.S.A. and Canada:
ꢙꢗꢄꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢇ^“ꢗꢄ{ꢅꢃꢇꢗ^ꢌꢅ^}ꢌꢂꢊꢄ]ꢇ`ꢊꢌꢗ^ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌ[ꢄꢗ}ꢁ`ꢃꢂꢌꢂꢗꢆ}ꢌꢗꢁꢃꢂꢇ}ꢊꢌꢗ“ꢌꢃ–ꢊꢌꢍ\ꢎ\ꢀ\ꢌꢅ^}ꢌŠꢅ^ꢅ}ꢅ‰ꢌ
`ꢗ^ꢃꢅ`ꢃꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢗꢄꢌ‡ꢗꢁꢄꢌꢆꢗ`ꢅꢆꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌ}ꢊꢅꢆꢊꢄ\ꢌ
ꢕ–ꢊꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ[ꢊꢄꢇꢗ}ꢌ“ꢗꢄꢌꢃ–ꢇꢂꢌ[ꢄꢗ}ꢁ`ꢃꢌꢇ^ꢌ{ꢅꢇ^ꢆꢅ^}ꢌŠ–ꢇ^ꢅꢌꢖ¤ꢗ^‚ꢌ¥ꢗ^‚‰ꢌƒꢅ`ꢅꢗꢌꢅ^}ꢌꢕꢅꢇꢋꢅ^ꢌ?„`ꢆꢁ}ꢊ}ꢚꢌꢇꢂꢌ
ꢂꢁ›œꢊ`ꢃꢌꢃꢗꢌꢃ–ꢊꢌꢃꢊꢄ{ꢂꢌꢅ^}ꢌ`ꢗ^}ꢇꢃꢇꢗ^ꢂꢌꢗ“ꢌꢃ–ꢊꢌƒꢅꢇ^ꢃꢊ^ꢅ^`ꢊꢌ”ꢁꢅꢄꢅ^ꢃꢊꢊꢌŠꢅꢄ}\
ꢙꢗꢄꢌꢁꢂꢊꢄꢂꢌꢇ^ꢌ?ꢁꢄꢗ[ꢊꢌꢅ^}ꢌ†ꢁꢂꢂꢇꢅ‰ꢌ“ꢁꢆꢆꢌ}ꢊꢃꢅꢇꢆꢂꢌꢗ“ꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ[ꢄꢗ]ꢇ}ꢊ}ꢌ`ꢅ^ꢌ›ꢊꢌ“ꢗꢁ^}ꢌꢇ^ꢌꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`ꢊꢁꢄꢗ[ꢊ\
`ꢗ{ꢌꢁ^}ꢊꢄꢌꢎꢁ[[ꢗꢄꢃꢈ¦ꢅꢄꢄꢅ^ꢃ‡ꢌ^“ꢗꢄ{ꢅꢃꢇꢗ^\
ꢜ\ꢝ‘ꢌŒꢄꢗœꢊ`ꢃꢗꢄꢌ¦ꢅꢄꢄꢅ^ꢃ‡ꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌŒ†§¨¦ꢒꢐꢌ†ꢊ]\ꢌꢐ–ꢌꢒꢛꢘꢔ$ꢘꢒ!
Download from Www.Somanuals.com. All Manuals Search And Download.
81
Mexico Lim®ited Warranty
VIEWSONIC PROJECTOR
What the warranty covers:
™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢋꢅꢄꢄꢅ^ꢃꢂꢌꢇꢃꢂꢌ[ꢄꢗ}ꢁ`ꢃꢂꢌꢃꢗꢌ›ꢊꢌ“ꢄꢊꢊꢌ“ꢄꢗ{ꢌ}ꢊ“ꢊ`ꢃꢂꢌꢇ^ꢌ{ꢅꢃꢊꢄꢇꢅꢆꢌꢅ^}ꢌꢋꢗꢄ|{ꢅ^ꢂ–ꢇ[‰ꢌꢁ^}ꢊꢄꢌ^ꢗꢄ{ꢅꢆꢌꢁꢂꢊ‰ꢌ}ꢁꢄꢇ^‚ꢌꢃ–ꢊꢌ
ꢋꢅꢄꢄꢅ^ꢃ‡ꢌ[ꢊꢄꢇꢗ}\ꢌ“ꢌꢅꢌ[ꢄꢗ}ꢁ`ꢃꢌ[ꢄꢗ]ꢊꢂꢌꢃꢗꢌ›ꢊꢌ}ꢊ“ꢊ`ꢃꢇ]ꢊꢌꢇ^ꢌ{ꢅꢃꢊꢄꢇꢅꢆꢌꢗꢄꢌꢋꢗꢄ|{ꢅ^ꢂ–ꢇ[ꢌ}ꢁꢄꢇ^‚ꢌꢃ–ꢊꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌ[ꢊꢄꢇꢗ}‰ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌ
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include
ꢄꢊ{ꢅ^ꢁ“ꢅ`ꢃꢁꢄꢊ}ꢌꢗꢄꢌꢄꢊ“ꢁꢄ›ꢇꢂ–ꢊ}ꢌ[ꢅꢄꢃꢂꢌꢗꢄꢌ`ꢗ{[ꢗ^ꢊ^ꢃꢂꢌ˜ꢌꢅ``ꢊꢂꢂꢗꢄꢇꢊꢂ\
How long the warranty is effective:
ꢝꢌ‡ꢊꢅꢄꢂꢌ“ꢗꢄꢌꢅꢆꢆꢌ[ꢅꢄꢃꢂꢌꢊ„`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌꢆꢅ{[‰ꢌꢝꢌ‡ꢊꢅꢄꢂꢌ“ꢗꢄꢌꢆꢅ›ꢗꢄ‰ꢌꢐꢌ‡ꢊꢅꢄꢌ“ꢗꢄꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌꢆꢅ{[ꢌ“ꢄꢗ{ꢌꢃ–ꢊꢌ}ꢅꢃꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ
consumer purchase.
ꢅ{[ꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢂꢁ›œꢊ`ꢃꢌꢃꢗꢌꢃꢊꢄ{ꢂꢌꢅ^}ꢌ`ꢗ^}ꢇꢃꢇꢗ^ꢂ‰ꢌ]ꢊꢄꢇ[`ꢅꢃꢇꢗ^ꢌꢅ^}ꢌꢅ[[ꢄꢗ]ꢅꢆ\ꢌꢀ[[ꢆꢇꢊꢂꢌꢃꢗꢌ{ꢅ^ꢁ“ꢅ`ꢃꢁꢄꢊꢄRꢂꢌꢇ^ꢂꢃꢅꢆꢆꢊ}ꢌꢆꢅ{[ꢌ
only.
ꢀꢆꢆꢌꢅ``ꢊꢂꢂꢗꢄ‡ꢌꢆꢅ{[ꢂꢌ[ꢁꢄ`–ꢅꢂꢊ}ꢌꢂꢊ[ꢅꢄꢅꢃꢊꢆ‡ꢌꢅꢄꢊꢌꢋꢅꢄꢄꢅ^ꢃꢊ}ꢌ“ꢗꢄꢌ=ꢒꢌ}ꢅ‡ꢂ\
Who the warranty protects:
ꢕ–ꢇꢂꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢇꢂꢌ]ꢅꢆꢇ}ꢌꢗ^ꢆ‡ꢌ“ꢗꢄꢌꢃ–ꢊꢌ[ꢄꢂꢃꢌ`ꢗ^ꢂꢁ{ꢊꢄꢌ[ꢁꢄ`–ꢅꢂꢊꢄ\
What the warranty does not cover:
ꢐ\ꢌ ꢀ^‡ꢌ[ꢄꢗ}ꢁ`ꢃꢌꢗ^ꢌꢋ–ꢇ`–ꢌꢃ–ꢊꢌꢂꢊꢄꢇꢅꢆꢌ^ꢁ{›ꢊꢄꢌ–ꢅꢂꢌ›ꢊꢊ^ꢌ}ꢊ“ꢅ`ꢊ}‰ꢌ{ꢗ}ꢇ[ꢊ}ꢌꢗꢄꢌꢄꢊ{ꢗ]ꢊ}\
ꢔ\ꢌ ˆꢅ{ꢅ‚ꢊ‰ꢌ}ꢊꢃꢊꢄꢇꢗꢄꢅꢃꢇꢗ^ꢌꢗꢄꢌ{ꢅꢆ“ꢁ^`ꢃꢇꢗ^ꢌꢄꢊꢂꢁꢆꢃꢇ^‚ꢌ“ꢄꢗ{‘
ꢌ
ꢅ\ꢌ ꢌꢀ``ꢇ}ꢊ^ꢃ‰ꢌ{ꢇꢂꢁꢂꢊ‰ꢌ^ꢊ‚ꢆꢊ`ꢃ‰ꢌ[ꢄꢊ‰ꢌꢋꢅꢃꢊꢄ‰ꢌꢆꢇ‚–ꢃ^ꢇ^‚‰ꢌꢗꢄꢌꢗꢃ–ꢊꢄꢌꢅ`ꢃꢂꢌꢗ“ꢌ^ꢅꢃꢁꢄꢊ‰ꢌꢁ^ꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌ[ꢄꢗ}ꢁ`ꢃꢌ{ꢗ}ꢇ[`ꢅꢃꢇꢗ^‰ꢌ
ꢁ^ꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌꢅꢃꢃꢊ{[ꢃꢊ}ꢌꢄꢊ[ꢅꢇꢄ‰ꢌꢗꢄꢌ“ꢅꢇꢆꢁꢄꢊꢌꢃꢗꢌ“ꢗꢆꢆꢗꢋꢌꢇ^ꢂꢃꢄꢁ`ꢃꢇꢗ^ꢂꢌꢂꢁ[[ꢆꢇꢊ}ꢌꢋꢇꢃ–ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ\
›\ꢌ ꢌꢀ^‡ꢌ}ꢅ{ꢅ‚ꢊꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌ}ꢁꢊꢌꢃꢗꢌꢂ–ꢇ[{ꢊ^ꢃ\
ꢌ
ꢌ
ꢌ
ꢌ
ꢌ
`\ꢌ ꢌŠꢅꢁꢂꢊꢂꢌꢊ„ꢃꢊꢄ^ꢅꢆꢌꢃꢗꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ‰ꢌꢂꢁ`–ꢌꢅꢂꢌꢊꢆꢊ`ꢃꢄꢇ`ꢅꢆꢌ[ꢗꢋꢊꢄꢌ\ꢁ`ꢃꢁꢅꢃꢇꢗ^ꢂꢌꢗꢄꢌ“ꢅꢇꢆꢁꢄꢊ\
}\ꢌ ꢍꢂꢊꢌꢗ“ꢌꢂꢁ[[ꢆꢇꢊꢂꢌꢗꢄꢌ[ꢅꢄꢃꢂꢌ^ꢗꢃꢌ{ꢊꢊꢃꢇ^‚ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`Rꢂꢌꢂ[ꢊ`ꢇ[`ꢅꢃꢇꢗ^ꢂ\
ꢊ\ꢌ ꢉꢗꢄ{ꢅꢆꢌꢋꢊꢅꢄꢌꢅ^}ꢌꢃꢊꢅꢄ\
“\ꢌ ꢀ^‡ꢌꢗꢃ–ꢊꢄꢌ`ꢅꢁꢂꢊꢌꢋ–ꢇ`–ꢌ}ꢗꢊꢂꢌ^ꢗꢃꢌꢄꢊꢆꢅꢃꢊꢌꢃꢗꢌꢅꢌ[ꢄꢗ}ꢁ`ꢃꢌ}ꢊ“ꢊ`ꢃ\
ꢝ\ꢌ ꢌꢀ^‡ꢌ[ꢄꢗ}ꢁ`ꢃꢌꢊ„–ꢇ›ꢇꢃꢇ^‚ꢌꢅꢌ`ꢗ^}ꢇꢃꢇꢗ^ꢌ`ꢗ{{ꢗ^ꢆ‡ꢌ|^ꢗꢋ^ꢌꢅꢂꢌOꢇ{ꢅ‚ꢊꢌ›ꢁꢄ^ꢘꢇ^Pꢌꢋ–ꢇ`–ꢌꢄꢊꢂꢁꢆꢃꢂꢌꢋ–ꢊ^ꢌꢅꢌꢂꢃꢅꢃꢇ`ꢌꢇ{ꢅ‚ꢊꢌꢇꢂꢌ
}ꢇꢂ[ꢆꢅ‡ꢊ}ꢌꢗ^ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌ“ꢗꢄꢌꢅ^ꢌꢊ„ꢃꢊ^}ꢊ}ꢌ[ꢊꢄꢇꢗ}ꢌꢗ“ꢌꢃꢇ{ꢊ\
ꢜ\ꢌ ꢌ†ꢊ{ꢗ]ꢅꢆ‰ꢌꢇ^ꢂꢃꢅꢆꢆꢅꢃꢇꢗ^‰ꢌꢇ^ꢂꢁꢄꢅ^`ꢊ‰ꢌꢅ^}ꢌꢂꢊꢃꢘꢁ[ꢌꢂꢊꢄ]ꢇ`ꢊꢌ`–ꢅꢄ‚ꢊꢂ\
How to get service:
ꢙꢗꢄꢌꢇ^“ꢗꢄ{ꢅꢃꢇꢗ^ꢌꢅ›ꢗꢁꢃꢌꢄꢊ`ꢊꢇ]ꢇ^‚ꢌꢂꢊꢄ]ꢇ`ꢊꢌꢁ^}ꢊꢄꢌꢋꢅꢄꢄꢅ^ꢃ‡‰ꢌ`ꢗ^ꢃꢅ`ꢃꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌŠꢁꢂꢃꢗ{ꢊꢄꢌꢎꢁ[[ꢗꢄꢃꢌꢖŒꢆꢊꢅꢂꢊꢌꢄꢊ“ꢊꢄꢌꢃꢗꢌꢃ–ꢊꢌ
ꢅꢃꢃꢅ`–ꢊ}ꢌŠꢁꢂꢃꢗ{ꢊꢄꢌꢎꢁ[[ꢗꢄꢃꢌ[ꢅ‚ꢊꢚ\ꢌ•ꢗꢁꢌꢋꢇꢆꢆꢌ^ꢊꢊ}ꢌꢃꢗꢌ[ꢄꢗ]ꢇ}ꢊꢌ‡ꢗꢁꢄꢌ[ꢄꢗ}ꢁ`ꢃRꢂꢌꢂꢊꢄꢇꢅꢆꢌ^ꢁ{›ꢊꢄ‰ꢌꢂꢗꢌ[ꢆꢊꢅꢂꢊꢌꢄꢊ`ꢗꢄ}ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌ
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.
For Your Records
Œꢄꢗ}ꢁ`ꢃꢌꢉꢅ{ꢊ‘ꢌ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨ꢌ
ˆꢗ`ꢁ{ꢊ^ꢃꢌꢉꢁ{›ꢊꢄ‘ꢌ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨ꢌ
Œꢁꢄ`–ꢅꢂꢊꢌˆꢅꢃꢊ‘ꢌ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨ꢌ
ƒꢗ}ꢊꢆꢌꢉꢁ{›ꢊꢄ‘ꢌ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨
ꢎꢊꢄꢇꢅꢆꢌꢉꢁ{›ꢊꢄ‘ꢌ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨
?„ꢃꢊ^}ꢊ}ꢌ¦ꢅꢄꢄꢅ^ꢃ‡ꢌŒꢁꢄ`–ꢅꢂꢊ©ꢌ¨¨¨¨¨¨¨¨¨¨¨¨¨¨¨ꢖ•ꢈꢉꢚ
“ꢌꢂꢗ‰ꢌꢋ–ꢅꢃꢌ}ꢅꢃꢊꢌ}ꢗꢊꢂꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢊ„[ꢇꢄꢊ©ꢌ¨¨¨¨¨¨¨¨¨
ꢌ
ꢌ
ꢌ
ꢌ
ꢌ
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c)
your address, (d) a description of the problem, and (e) the serial number of the product.
ꢔ\ꢌ ꢌꢕꢅ|ꢊꢌꢗꢄꢌꢂ–ꢇ[ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃꢌꢇ^ꢌꢃ–ꢊꢌꢗꢄꢇ‚ꢇ^ꢅꢆꢌ`ꢗ^ꢃꢅꢇ^ꢊꢄꢌ[ꢅ`|ꢅ‚ꢇ^‚ꢌꢃꢗꢌꢅ^ꢌꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢂꢊꢄ]ꢇ`ꢊꢌ`ꢊ^ꢃꢊꢄ\
ꢝ\ꢌ †ꢗꢁ^}ꢌꢃꢄꢇ[ꢌꢃꢄꢅ^ꢂ[ꢗꢄꢃꢅꢃꢇꢗ^ꢌ`ꢗꢂꢃꢂꢌ“ꢗꢄꢌꢇ^ꢘꢋꢅꢄꢄꢅ^ꢃ‡ꢌ[ꢄꢗ}ꢁ`ꢃꢂꢌꢋꢇꢆꢆꢌ›ꢊꢌ[ꢅꢇ}ꢌ›‡ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`\
Limitation of implied warranties:
ꢕ–ꢊꢄꢊꢌꢅꢄꢊꢌ^ꢗꢌꢋꢅꢄꢄꢅ^ꢃꢇꢊꢂ‰ꢌꢊ„[ꢄꢊꢂꢂꢌꢗꢄꢌꢇ{[ꢆꢇꢊ}‰ꢌꢋ–ꢇ`–ꢌꢊ„ꢃꢊ^}ꢌ›ꢊ‡ꢗ^}ꢌꢃ–ꢊꢌ}ꢊꢂ`ꢄꢇ[ꢃꢇꢗ^ꢌ`ꢗ^ꢃꢅꢇ^ꢊ}ꢌ–ꢊꢄꢊꢇ^ꢌꢇ^`ꢆꢁ}ꢇ^‚ꢌꢃ–ꢊꢌ
ꢇ{[ꢆꢇꢊ}ꢌꢋꢅꢄꢄꢅ^ꢃ‡ꢌꢗ“ꢌ{ꢊꢄ`–ꢅ^ꢃꢅ›ꢇꢆꢇꢃ‡ꢌꢅ^}ꢌ[ꢃ^ꢊꢂꢂꢌ“ꢗꢄꢌꢅꢌ[ꢅꢄꢃꢇ`ꢁꢆꢅꢄꢌ[ꢁꢄ[ꢗꢂꢊ\
Exclusion of damages:
™ꢇꢊꢋꢎꢗ^ꢇ`Rꢂꢌꢆꢇꢅ›ꢇꢆꢇꢃ‡ꢌꢇꢂꢌꢆꢇ{ꢇꢃꢊ}ꢌꢃꢗꢌꢃ–ꢊꢌ`ꢗꢂꢃꢌꢗ“ꢌꢄꢊ[ꢅꢇꢄꢌꢗꢄꢌꢄꢊ[ꢆꢅ`ꢊ{ꢊ^ꢃꢌꢗ“ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ\ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌꢂ–ꢅꢆꢆꢌ^ꢗꢃꢌ›ꢊꢌꢆꢇꢅ›ꢆꢊꢌ“ꢗꢄ‘
ꢐ\ꢌ ꢌˆꢅ{ꢅ‚ꢊꢌꢃꢗꢌꢗꢃ–ꢊꢄꢌ[ꢄꢗ[ꢊꢄꢃ‡ꢌ`ꢅꢁꢂꢊ}ꢌ›‡ꢌꢅ^‡ꢌ}ꢊ“ꢊ`ꢃꢂꢌꢇ^ꢌꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ‰ꢌ}ꢅ{ꢅ‚ꢊꢂꢌ›ꢅꢂꢊ}ꢌꢁ[ꢗ^ꢌꢇ^`ꢗ^]ꢊ^ꢇꢊ^`ꢊ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌꢁꢂꢊꢌꢗ“ꢌ
ꢃ–ꢊꢌ[ꢄꢗ}ꢁ`ꢃ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌꢃꢇ{ꢊ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌ[ꢄꢗ[ꢃꢂ‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌ›ꢁꢂꢇ^ꢊꢂꢂꢌꢗ[[ꢗꢄꢃꢁ^ꢇꢃ‡‰ꢌꢆꢗꢂꢂꢌꢗ“ꢌ‚ꢗꢗ}ꢋꢇꢆꢆ‰ꢌꢇ^ꢃꢊꢄ“ꢊꢄꢊ^`ꢊꢌꢋꢇꢃ–ꢌ›ꢁꢂꢇ^ꢊꢂꢂꢌ
relationships, or other commercial loss, even if advised of the possibility of such damages.
ꢔ\ꢌ ꢌꢀ^‡ꢌꢗꢃ–ꢊꢄꢌ}ꢅ{ꢅ‚ꢊꢂ‰ꢌꢋ–ꢊꢃ–ꢊꢄꢌꢇ^`ꢇ}ꢊ^ꢃꢅꢆ‰ꢌ`ꢗ^ꢂꢊ£ꢁꢊ^ꢃꢇꢅꢆꢌꢗꢄꢌꢗꢃ–ꢊꢄꢋꢇꢂꢊ\
ꢝ\ꢌ ꢀ^‡ꢌ`ꢆꢅꢇ{ꢌꢅ‚ꢅꢇ^ꢂꢃꢌꢃ–ꢊꢌ`ꢁꢂꢃꢗ{ꢊꢄꢌ›‡ꢌꢅ^‡ꢌꢗꢃ–ꢊꢄꢌ[ꢅꢄꢃ‡\
ꢜ\ꢌ †ꢊ[ꢅꢇꢄꢌꢗꢄꢌꢅꢃꢃꢊ{[ꢃꢊ}ꢌꢄꢊ[ꢅꢇꢄꢌ›‡ꢌꢅ^‡ꢗ^ꢊꢌ^ꢗꢃꢌꢅꢁꢃ–ꢗꢄꢇšꢊ}ꢌ›‡ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`\
Download from Www.Somanuals.com. All Manuals Search And Download.
82
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
ƒꢞ„ꢇ`ꢗ‰ꢌꢀ]\ꢌ}ꢊꢌꢆꢅꢌŒꢅꢆ{ꢅꢌ—ꢑꢌŒꢇꢂꢗꢌꢔꢌˆꢊꢂ[ꢅ`–ꢗꢌꢔꢒꢝ‰ꢌŠꢗꢄ[ꢗꢄꢅꢃꢇ]ꢗꢌ^ꢃꢊꢄ[ꢅꢆ{ꢅꢂ‰
Šꢗꢆ\ꢌꢎꢅ^ꢌꢙꢊꢄ^ꢅ^}ꢗꢌ¤ꢁꢇ„£ꢁꢇꢆꢁ`ꢅ^‰ꢌ?ꢂꢃꢅ}ꢗꢌ}ꢊꢌƒꢞ„ꢇ`ꢗ
ꢕꢊꢆ‘ꢌꢖ$$ꢚꢌꢝꢛꢒ$ꢘꢐꢒ==ꢌꢌꢌꢌꢌ–ꢃꢃ[‘ꢈꢈꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{ꢈꢆꢅꢈꢂꢗ[ꢗꢄꢃꢊꢈꢇ^}ꢊ„\–ꢃ{
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Villahermosa:
ˆꢇꢂꢃꢄꢇ›ꢁ`ꢇꢗ^ꢊꢂꢌ‡ꢌꢎꢊꢄ]ꢇ`ꢇꢗꢂꢌŠꢗ{[ꢁꢃꢅ`ꢇꢗ^ꢅꢆꢊꢂꢌꢎꢀꢌ}ꢊꢌŠ™\
Šꢅꢆꢆꢊꢌ§ꢁꢅꢄꢊšꢌꢔꢑꢜꢌꢆꢗ`ꢅꢆꢌꢔ
Šꢗꢆ\ꢌꢁ‚ꢅ{›ꢇꢆꢇꢅꢂꢌŠ\Œ‘ꢌꢑꢝꢐꢜꢒ
ꢕꢊꢆ‘ꢌꢒꢐꢘꢛꢛꢘꢔꢔꢘꢐꢜꢘ=ꢒꢒ$
?ꢘƒꢅꢇꢆ‘ꢌ}ꢇꢂ`ꢔ«–{ꢗ\{ꢊ‚ꢅꢄꢊ}\^ꢊꢃ\{„
Šꢗ{[ꢁ{ꢅ^ꢃꢊ^ꢇ{ꢇꢊꢃ^ꢗꢂꢌ”ꢅꢄꢅ^ꢃꢇšꢅ}ꢗꢂ‰ꢌꢎ\ꢀ\ꢌ}ꢊꢌŠ\™\
ꢀ™\ꢌ”†?”‹†‹ꢌƒ?ꢉˆ?ꢓꢌ—ꢐ$ꢒꢜ
Š‹‰ꢌꢙ‹†ˆꢀꢌŠ\Œ\ꢌꢑꢛꢒꢜꢒ
ꢕꢊꢆ‘ꢌꢒꢐꢌꢖ==ꢝꢚꢌꢝꢌ$ꢔꢌꢒꢒꢌꢜ!ꢌꢈꢌꢝ$ꢔꢔꢒ!ꢜꢌꢈꢌꢝꢌ$ꢔꢌꢔꢒꢌꢒ=
?ꢘƒꢅꢇꢆ‘ꢌ`ꢗ{[ꢁ{ꢅ^ꢃꢊ^ꢇ{ꢇꢊ^ꢃꢗꢂ«[ꢄꢗ}ꢇ‚‡\^ꢊꢃ\{„
Veracruz, Ver.:
Puebla, Pue. (Matriz):
†?ꢉꢕꢀꢌ•ꢌˆꢀꢕ‹ꢎ‰ꢌꢎ\ꢀ\ꢌˆ?ꢌŠ\™\ꢌˆꢗ{ꢇ`ꢇꢆꢇꢗ‘
ꢔ=ꢌꢎꢍ†ꢌ!ꢔꢐꢌŠ‹\ꢌꢀꢌŒꢀꢓ
!ꢔꢐꢛꢒꢌŒꢍ?ꢀ‰ꢌŒꢍ?\
Š‹ꢉ?¬‹ꢉꢌ•ꢌˆ?ꢎꢀ††‹‹‰ꢌꢎ\ꢀꢌˆ?ꢌŠ\™\ꢌꢌꢀ]\ꢌꢀ{ꢊꢄꢇ`ꢅꢂꢌ—ꢌꢜꢐ=
?ꢉꢕ†?ꢌŒꢉꢓꢟꢉꢌ•ꢌꢀ™ꢀ†ꢀˆ‹
ꢙꢄꢅ``\ꢌ†ꢊ“ꢗꢄ{ꢅꢌŠ\Œ\ꢌ=ꢐ=ꢐ=
ꢕꢊꢆ‘ꢌꢒꢐꢖ$ꢔꢚ\ꢔꢔꢔ\ꢑ=ꢐ\$$\!!ꢌŠ‹ꢉꢌꢐꢒꢌꢉ?ꢀꢎ
?ꢘƒꢅꢇꢆ‘ꢌ}ꢅꢃꢗꢂ«[ꢁꢊ›ꢆꢅ\{ꢊ‚ꢅꢄꢊ}\^ꢊꢃ\{„
Chihuahua
ꢎꢗꢆꢁ`ꢇꢗ^ꢊꢂꢌ”ꢆꢗ›ꢅꢆꢊꢂꢌꢊ^ꢌŠꢗ{[ꢁꢃꢅ`ꢇꢠ^
Š\ꢌƒꢅ‚ꢇꢂꢃꢊꢄꢇꢗꢌ—ꢌꢝꢝꢔꢐꢌŠꢗꢆ\ꢌƒꢅ‚ꢇꢂꢃꢊꢄꢇꢅꢆ
Chihuahua, Chih.
ꢕꢊꢆ‘ꢌꢜꢐꢝꢛ=$ꢜ
?ꢘƒꢅꢇꢆ‘ꢌŠꢊ“ꢊꢗ«ꢂꢗꢆꢁ‚ꢆꢗ›ꢅꢆꢊꢂ\`ꢗ{
Distrito Federal:
ꢕꢊꢆ‘ꢌꢒꢐꢘꢔꢔꢘ=ꢐꢘꢒꢒꢘꢝꢐꢘꢛ!
?ꢘƒꢅꢇꢆ‘ꢌ‚ꢅ`ꢗꢂꢃꢅ«£[ꢆꢁꢂ\`ꢗ{\{„
Cuernavaca
Šꢗ{[ꢁꢂꢁ[[ꢗꢄꢃꢌ}ꢊꢌŠꢁꢊꢄ^ꢅ]ꢅ`ꢅꢌꢎꢀꢌ}ꢊꢌŠ™
ꢙꢄꢅ^`ꢇꢂ`ꢗꢌꢊ‡]ꢅꢌ—ꢌꢐ!ꢑꢌŠꢗꢆ\ꢌƒꢇ‚ꢁꢊꢆꢌ¤ꢇ}ꢅꢆ‚ꢗ
Š\Œ\ꢌꢛꢔꢒꢜꢒ‰ꢌŠꢁꢊꢄ^ꢅ]ꢅ`ꢅꢌƒꢗꢄꢊꢆꢗꢂ
ꢕꢊꢆ‘ꢌꢒꢐꢌ!!!ꢌꢝꢐꢑꢒ$!=ꢌꢈꢌꢒꢐꢌ!!!ꢌꢝꢐꢔꢜꢒꢐꢜ
?ꢘƒꢅꢇꢆ‘ꢌꢅ£ꢁꢊ]ꢊ}ꢗ«`ꢗ{[ꢁꢂꢁ[[ꢗꢄꢃ`]ꢅ\`ꢗ{
Guadalajara, Jal.:
ꢡŒꢍꢎ‰ꢌꢎ\ꢀ\ꢌ}ꢊꢌŠ\™\
ꢎ?†™Š†?Š?‰ꢌꢎ\ꢀ\ꢌ}ꢊꢌŠ\™\
ꢀ]\ꢌŠꢗ‡ꢗꢅ`ꢢ^ꢌ=ꢝꢐ
ꢀ]\ꢌꢉꢇꢣꢗꢂꢌ¤ꢞꢄꢗꢊꢂꢌ—ꢌꢔꢔꢑꢐ
Šꢗꢆ\ꢌˆꢊꢆꢌ™ꢅꢆꢆꢊꢌꢒꢝꢐꢒꢒ‰ꢌƒꢞ„ꢇ`ꢗ‰ꢌˆ\ꢙ\
ꢕꢊꢆ‘ꢌꢒꢐꢖ$ꢔꢚ$$ꢘ$ꢒꢘꢒꢒꢘꢔ!ꢘꢝ$
?ꢘƒꢅꢇꢆꢌ‘ꢌ‚ꢅ`ꢗꢂꢃꢅ«£[ꢆꢁꢂ\`ꢗ{\{„
Šꢗꢆ\ꢌꢀꢄ`ꢗꢂꢌꢎꢁꢄ‰ꢌꢎꢊ`ꢃꢗꢄꢌ§ꢁꢢꢄꢊš
ꢜꢜꢐ!ꢒ‰ꢌ”ꢁꢅ}ꢅꢆꢅœꢅꢄꢅ‰ꢌ§ꢅꢆꢇꢂ`ꢗ
ꢕꢊꢆ‘ꢌꢒꢐꢖ$ꢔꢚꢝꢝꢘꢝꢛꢘꢐ$ꢘꢐ$ꢘꢜꢝ
?ꢘƒꢅꢇꢆ‘ꢌ{{ꢇꢄꢅ^}ꢅ«ꢂꢊꢄ]ꢇ`ꢄꢊ`ꢊ\`ꢗ{
Guerrero Acapulco
Monterrey:
”ꢆꢗ›ꢅꢆꢌŒꢄꢗ}ꢁ`ꢃꢌꢎꢊꢄ]ꢇ`ꢊꢂ
ƒꢅꢄꢌŠꢅꢄꢇ›ꢊꢌ—ꢌꢐ=ꢑ!‰ꢌ?ꢂ£ꢁꢇ^ꢅꢌ`ꢗ^ꢌ”ꢗꢆ“ꢗꢌŒꢞꢄꢂꢇ`ꢗ
ꢙꢄꢅ``\ꢌꢊꢄ^ꢅꢄ}ꢗꢌ†ꢊ‡ꢊꢂ‰ꢌŠŒꢌꢛꢜꢔꢑꢒ
ƒꢗ^ꢃꢊꢄꢄꢊ‡ꢌꢉ\\ꢌƒꢞ„ꢇ`ꢗ
”ꢎꢌŠꢗ{[ꢁꢃꢅ`ꢇꢠ^ꢌꢖ”ꢄꢁ[ꢗꢌꢎꢊꢂꢇ`ꢗ{[ꢚ
Œꢄꢗ‚ꢄꢊꢂꢗꢌ—ꢛꢘꢀ‰ꢌŠꢗꢆꢗꢌŠꢊ^ꢃꢄꢗ
ꢝ=ꢝꢒꢒꢌꢀ`ꢅ[ꢁꢆ`ꢗ‰ꢌ”ꢁꢊꢄꢄꢊꢄꢗ
ꢕꢊꢆ‘ꢌ!ꢜꢜꢘꢜꢑꢘꢝꢔꢛꢔ!
ꢕꢊꢆ‘ꢌꢑꢐꢔ=ꢘ$ꢐꢒꢝ
?ꢘƒꢅꢇꢆ‘ꢌꢅ‡}ꢊꢊ{«‚[ꢂꢐ\`ꢗ{\{„
MERIDA:
??Šꢕ†‹ꢎ?†
ꢀ]ꢌ†ꢊ“ꢗꢄ{ꢅꢌꢉꢗ\ꢌꢜꢒꢝ”„ꢝ=ꢌ‡ꢌꢜꢐ
ƒꢞꢄꢇ}ꢅ‰ꢌ•ꢁ`ꢅꢃꢢ^‰ꢌƒꢞ„ꢇ`ꢗꢌꢌŠŒ=!ꢒꢒꢒ
ꢕꢊꢆ‘ꢌꢖ$ꢔꢚꢌ===ꢘ=ꢔ$ꢘꢐ=ꢐꢛ
?ꢘƒꢅꢇꢆ‘ꢌꢄꢄꢄ›«ꢂꢁꢄꢊꢂꢃꢊ\`ꢗ{
Oaxaca, Oax.:
Š?ꢉꢕ†‹ꢌˆ?ꢌˆꢎꢕ†ꢍŠ‹ꢉꢌ•
ꢎ?†™Š‹‰ꢌꢎ\ꢀ\ꢌ}ꢊꢌŠ\™\
ƒꢁꢄ‚ꢁꢤꢅꢌ—ꢌ!ꢒꢑꢌŒ\ꢀ\‰ꢌŠꢗꢆ\ꢌŠꢊ^ꢃꢄꢗ‰ꢌꢛꢑꢒꢒꢒ‰ꢌ‹ꢅ„ꢅ`ꢅ
ꢕꢊꢆ‘ꢌꢒꢐꢖ$ꢔꢚ=$ꢘꢐ$ꢘꢐ$ꢘꢔꢔꢘꢔꢔ
ꢙꢅ„‘ꢌꢒꢐꢖ$ꢔꢚ=$ꢘꢐ$ꢘꢐꢝꢘꢛ!ꢘꢒꢒꢌ
?ꢘƒꢅꢇꢆ\ꢌ‚[ꢗꢃꢅꢇꢔꢒꢒꢐ«–ꢗꢃ{ꢅꢇꢆ\`ꢗ{
Tijuana:
ꢎꢕˆ
FOR USA SUPPORT:
™ꢇꢊꢋꢎꢗ^ꢇ`ꢌŠꢗꢄ[ꢗꢄꢅꢃꢇꢗ^ꢌ
ꢀ]ꢌꢙꢊꢄꢄꢗ`ꢅꢄꢄꢇꢆꢌꢎꢗ^ꢗꢄꢅꢌ—ꢝ!ꢑꢒꢌꢘŠꢌ
Šꢗꢆꢌꢔꢒꢌ}ꢊꢌꢉꢗ]ꢇꢊ{›ꢄꢊ
ꢕꢇœꢁꢅ^ꢅ‰ꢌƒꢊ„ꢇ`ꢗ
ꢝꢑꢐꢌꢄꢊꢅꢌŠꢅ^‡ꢗ^ꢌ†ꢗꢅ}‰ꢌ¦ꢅꢆ^ꢁꢃ‰ꢌŠꢀ\ꢌ=ꢐ!ꢑ=ꢌꢍꢎꢀ
ꢕꢊꢆ‘ꢌꢑꢒꢒꢘꢛꢑꢑꢘꢛꢛꢑꢑꢌꢖ?^‚ꢆꢇꢂ–ꢚžꢌꢌꢑꢛꢛꢘꢝꢔꢝꢘꢑꢒ$ꢛꢌꢖꢎ[ꢅ^ꢇꢂ–ꢚž
ꢙꢅ„‘ꢌꢐꢘꢑꢒꢒꢘꢛꢑ$ꢘ!ꢔ!ꢛ
?ꢘƒꢅꢇꢆ‘ꢌ–ꢃꢃ[‘ꢈꢈꢋꢋꢋ\]ꢇꢊꢋꢂꢗ^ꢇ`\`ꢗ{
ꢜ\ꢝ‘ꢌ™ꢇꢊꢋꢎꢗ^ꢇ`ꢌƒꢊ„ꢇ`ꢗꢌꢇ{ꢇꢃꢊ}ꢌ¦ꢅꢄꢄꢅ^ꢃ‡ꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌꢌŒ†§¨¦ꢒꢝꢌ†ꢊ]\ꢌꢐꢀꢌꢒꢛꢘꢔ$ꢘꢒ!
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Download from Www.Somanuals.com. All Manuals Search And Download.
|