Vermont Casting Water Heater SDDVT User Manual
INSTALLER / CONSUMER  
SAFETY INFORMATION  
PLEASE READ THIS MANUAL  
BEFORE INSTALLING AND USING  
APPLIANCE.  
Stardance  
WARNING!  
IF THE INFORMATION IN THIS  
MANUAL IS NOT FOLLOWED  
EXACTLY, A FIRE OR EXPLOSION  
MAY RESULT CAUSING  
PROPERTY DAMAGE, PERSONAL  
INJURY OR LOSS OF LIFE.  
Direct Vent/Natural Vent  
Gas Heater  
Models:  
SDDVT Series: SDDVTCB, SDDVTEB, SDDVTMB,  
SDDVTBS, SDDVTCH, SDDVTVG, SDDVTBD,  
SDDVTC Series: SDDVTCCB, SDDVTCEB,  
SDDVTCMB, SDDVTCBS, SDDVTCCH, SDDVTCVG,  
SDDVTCBD  
FOR YOUR SAFETY  
Installation and service must be  
performed by a qualified installer, service  
agency or the gas suppler.  
WHAT TO DO IF YOU SMELL GAS:  
•
•
Do not try to light any appliance.  
Do not touch any electric switch; do  
not use any phone in your building.  
•
•
Immediately call your gas supplier from  
your neighbor’s phone. Follow the gas  
supplier’s instructions.  
If you cannot reach your gas supplier,  
call the fire department.  
DO NOT STORE OR USE  
GASOLINE OR OTHER  
FLAMMABLE VAPORS AND  
LIQUIDS IN THE VICINITY OF THIS  
OR ANY OTHER APPLIANCE.  
This appliance may be installed in an after  
market permanently located manufactured  
(mobile) home where not prohibited by  
local codes.  
Homeowner’s Installation  
and Operating Manual  
This appliance is only for use with the  
type of gas indicated on the rating plate.  
This appliance is not convertible for use  
with other gases unless a certified kit is  
used.  
CERTIFIED  
I
INSTALLER: Leave this manual with the appliance.  
CONSUMER: Retain this manual for future reference.  
20012734 3/08 Rev. 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
General Information  
The Stardance Direct Vent/Natural Vent Room Heater, Model  
Nos. SDDVTCB, SDDVTEB, SDDVTMB, SDDVTBS, SDDVTCH,  
SDDVTVG, SDDVTBD, SDDVTCCB, SDDVTCEB, SDDVTC-  
MB, SDDVTCBS, SDDVTCCH, SDDVTCVG, SDDVTCCBD, is  
a vented gas appliance listed to the ANSI standard Z21.88-2005  
and CSA-2.33-2005 for Vented Room Heaters, and CSA 2.17-  
M91, Gas-Fired Appliances For Use at High Altitudes.  
The installation of the Stardance Direct Vent/Natural Vent Room  
Heater must conform with local codes, or in the absence of lo-  
cal codes, with National Fuel Gas Code, ANSI Z223.1/NFPA 54  
— latest edition and CSA B-149.1 Installation Code. (EXCEP-  
TION: Do not derate this appliance for altitude. Maintain the  
manifold pressure at 3.5” w.c. for Natural Gas and 10.0” w.c. for  
LP gas at maximum input.)  
This appliance may be installed in an aftermarket* manufactured  
(mobile) home, where not prohibited by state or local codes.  
WARNING: Operation of this heater when not connected to a  
properly installed and maintained venting system can result  
in carbon monoxide (CO) poisoning and possible death.  
The Stardance Direct Vent/Natural Vent Room Heater, when in-  
stalled, must be electrically grounded in accordance with local  
codes or, in the absence of local codes, with the National Electri-  
cal Code ANSI/NFPA 70, (latest edition), or of the current Cana-  
dian Electrical Code C22.1.  
Due to high temperatures this appliance should be located  
out of traffic and away from furniture and draperies.  
WARNING: This appliance is hot while in operation. Keep  
children, clothing, and furniture away. Contact may cause  
burns or ignition of combustible materials.  
Children and adults should be alerted to the hazards of high  
surface temperatures and should stay away to avoid burns  
or clothing ignition. Young children should be carefully su-  
pervised when they are in the same room as the appliance.  
Clothing or other flammable materials should not be placed  
on or near the appliance.  
Any safety screen, glass or guard removed for servicing  
an appliance must be replaced prior to operating the appli-  
ance.  
The appliance area must be kept clear and free from com-  
bustible materials, gasoline, and other flammable vapors  
and liquids.  
The flow of combustion and ventilation air must not be ob-  
structed. The installation must include adequate accessibil-  
ity and clearance for servicing and proper operation.  
WARNING: Do not operate the Room Heater with the glass  
panel removed, cracked or broken. Replacement of the pan-  
el should be done by a licensed or qualified service person.  
This appliance is only for use with the type of gas indicated on  
the rating plate. This appliance is not convertible for use with  
other gases unless a certified kit is used.  
Installation and replacement of gas piping, gas utilization  
equipment or accessories, and repair and servicing of  
equipment shall be performed only by a qualified agency,  
preferably NFI or WETT (Canada) certified. The term “quali-  
fied agency” means any individual, firm, corporation, or  
company that either in person or through a representative  
is engaged in and is responsible for (a) installation or re-  
placement of gas piping, or (b), the connection, installation,  
repair, or servicing of equipment, who is experienced in  
such work, familiar with all precautions required, and has  
complied with all the requirements of the authority having  
jurisdiction.  
The Stardance Direct Vent/Natural Vent Room Heater should  
be inspected before use and at least annually by a qualified  
service agency. It is imperative that control compartments,  
burners, and circulating air passageways of the appliance  
be kept clean.  
Do not use this appliance if any part has been under water.  
Immediately call a qualified service technician to inspect the  
appliance and to replace any part of the control system and  
any gas control which has been under water.  
The Stardance Direct Vent/Natural Vent Room Heater and its  
individual shut-off valve must be disconnected from the gas sup-  
ply piping during any pressure testing of that system at test pres-  
sures in excess of 1/2 psig (3.5 kPa).  
Do not burn wood, trash or any other material for which this  
appliance was not designed. This appliance is designed to  
burn either natural gas or propane only.  
This gas appliance must not be connected to a chimney flue  
serving a separate solid-fuel burning appliance.  
The Stardance Direct Vent/Natural Vent Room Heater must be  
isolated from the gas supply piping system by closing its indi-  
vidual manual shutoff valve during any pressure testing of the  
gas supply piping system at test pressures equal to or less than  
1/2 psig.  
CAUTION: Label all wires prior to disconnection when ser-  
vicing controls. Wiring errors can cause improper and dan-  
gerous operation.  
Verify proper operation after servicing.  
* Aftermarket: Completion of sale, nor for purpose of resale, from the  
‘Direct Vent’ describes a sealed combustion system in which in-  
coming outside air for combustion and outgoing exhaust enter  
and exit through two separate concentric passages within the  
same sealed vent system. The system does not use room air to  
support combustion. The Direct Vent system permits the gas ap-  
pliance to be vented directly to the outside atmosphere through manufacturer.  
the side of the house or vertically through the roof. Conventional  
venting systems (Natural Vent) take air from the room for com-  
bustion and vent the exhaust vertically through the roof to the  
atmosphere.  
Proposition 65 Warning: Fuels used in gas, woodburning or  
This appliance is approved for bedroom installations in the U.S.  
and Canada.  
oil fired appliances, and the products of combustion of such  
fuels, contain chemicals known to the State of California to  
cause cancer, birth defects and other reproductive harm.  
California Health & Safety Code Sec. 25249.6  
20012734  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Installation Requirements  
Inspection  
Requirements for the Commonwealth of  
Massachusetts  
The state or local gas inspector of the side wall  
horizontally vented gas fueled equipment shall not  
approve the installation unless, upon inspection, the  
inspector observes carbon monoxide detectors and  
signage installed in accordance with the provisions of  
248 CMR 5.08(2)(a)1 through 4.  
All gas fitting and installation of this heater shall only be  
done by a licensed gas fitter or licensed plumber.  
For all side wall horizontally vented gas fueled  
equipment installed in every dwelling, building or  
structure used in whole or in part for residential  
purposes, including those owned or operated by the  
Commonwealth and where the side wall exhaust  
vent termination is less than seven (7) feet above  
finished grade in the area of the venting, including  
but not limited to decks and porches, the following  
requirements shall be satisfied:  
Exemptions  
The following equipment is exempt from 248 CMR  
5.08(2)(a)1 through 4:  
• The equipment listed in Chapter 10 entitled  
“Equipment Not Required To Be Vented” in the most  
current edition of NFPA 54 as adopted by the Board;  
and  
Installation of Carbon Monoxide Detectors  
• Product Approved side wall horizontally vented gas  
fueled equipment installed in a room or structure  
separate from the dwelling, building or structure  
used in whole or in part for residential purposes.  
At the time of installation of the side wall horizontal  
vented gas fueled equipment, the installing plumber  
or gas fitter shall observe that a hard wired carbon  
monoxide detector with an alarm is installed on each  
additional level of the dwelling, building or structure  
served by the side wall horizontal vented gas fueled  
equipment. It shall be the responsibility of the property  
owner to secure the services of qualified licensed  
professionals for the installation of hard wired carbon  
monoxide detectors.  
MANUFACTURER REQUIREMENTS  
Gas Equipment Venting System Provided  
When the manufacturer of Product Approved side  
wall horizontally vented gas equipment provides a  
venting system design or venting system components  
with the equipment, the instructions provided by the  
manufacturer for installation of the equipment and the  
venting system shall include:  
In the event that the side wall horizontally vented gas  
fueled equipment is installed in a crawl space or an  
attic, the hard wired carbon monoxide detector with  
alarm and battery back-up may be installed on the next  
adjacent floor level.  
• Detailed instructions for the installation of the venting  
system design or the venting system components;  
and  
In the event that the requirements of this subdivision  
can not be met at the time of completion of installation,  
the owner shall have a period of thirty (30) days  
to comply with the above requirements; provided,  
however, that during said thirty (30) day period, a  
battery operated carbon monoxide detector with an  
alarm shall be installed.  
• A complete parts list for the venting system design or  
venting system.  
Gas Equipment Venting System NOT Provided  
When the manufacturer of a Product Approved side  
wall horizontally vented gas fueled equipment does  
not provide the parts for venting the flue gases, but  
identifies “special venting systems”, the following  
requirements shall be satisfied by the manufacturer:  
Approved Carbon Monoxide Detectors  
Each carbon monoxide detector as required in  
accordance with the above provisions shall comply with  
NFPA 720 and ANSI/UL 2034 listed and IAS certified.  
• The referenced “special venting system” instructions  
shall be included with the appliance or equipment  
installation instructions; and  
Signage  
A metal or plastic identification plate shall be  
• The “special venting systems” shall be Product  
Approved by the Board, and the instructions for  
that system shall include a parts list and detailed  
installation instructions.  
permanently mounted to the exterior of the building at  
a minimum height of eight (8) feet above grade directly  
in line with the exhaust vent terminal for the horizontally  
vented gas fueled heating appliance or equipment. The  
sign shall read, in print size no less than one-half (1/2)  
inch in size, “GAS VENT DIRECTLY BELOW, KEEP  
CLEAR OF ALL OBSTRUCTIONS”.  
A copy of all installation instructions for all Product  
Approved side wall horizontally vented gas fueled  
equipment, all venting instructions, all parts lists  
for venting instructions, and/or all venting design  
instructions shall remain with the appliance or  
equipment at the completion of the installation.  
20012734  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Stardance Direct Vent / Natural Vent Dimensions  
7" Outer Dia.  
(178 mm)  
7" Outer Dia.  
(178 mm)  
Supply Inlet  
12���”  
Supply Inlet  
12���”  
(321 mm)  
(321 mm)  
2���”  
(73 mm)  
2���”  
(73 mm)  
9"  
8"  
C
C
L
Flue Collar  
L
(229 mm)  
(203 mm)  
Flue Collar  
C
L
8���"  
(222 mm)  
SDDVT Models  
SDDVTC Models  
7���”  
(197 mm)  
26���"  
(680 mm)  
Supply Inlet  
C
L
3"  
(76 mm)  
14���"  
25���"  
(355 mm)  
(648 mm)  
Fig. 1 Stardance dimensions.  
Attention  
The Stardance stove is shipped from the factory as a Direct Vent Gas Heater. This heater  
may be converted into a Natural Vent unit in the field. If a Natural Vent heater is desired,  
the Vermont Castings Z31B00 FSDHAG Draft Hood must be directly installed to the top  
of the unit according to the installation instructions. The Draft Hood Adapter is available  
in the 7FSDHASK stove kit or as a separate item.  
When the Stardance stove is converted to Natural Vent, it uses 4” vent pipe. For aes-  
thetic purposes the CFM direct vent system may be used up to the ceiling.  
20012734  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Installation Requirements  
The installation must conform with local codes or, in  
the absence of local codes, with the National Fuel Gas  
Code, ANSI Z223.1/NFPA 54 - latest edition. (EXCEP-  
TION: Do not derate this appliance for altitude. Main-  
tain the manifold pressure at 3.5 inches w.c. for Natural  
Gas, and 10 inches w.c. for Propane).  
A
D
B
C
In Canada, installation must be in accordance with the  
current CSA B-149.1 Installation Codes and/or local  
codes.  
E
The installation should be done by a qualified ser-  
vice person who is familiar with the building codes  
and installation techniques appropriate for your  
area to accomplish a safe and effective installation.  
ST207  
Fig. 2 Possible stove locations.  
Your dealer or your local gas supplier will be able to  
refer a qualified service person.  
Clearance Requirements  
WARNING: Due to high temperatures, the  
HEATER should be located out of traffic  
and away from furniture and draperies.  
Minimum Clearances to Combustible  
Materials  
The surface of the Heater Is hot when it is in use.  
Young children should be watched carefully when  
they are in the same room when the Heater is in  
use, and they should be taught to avoid the hot  
surface. Keep any objects that can burn well away  
from the Heater, and observe the recommended  
clearances that follow.  
Measure side clearances as shown in Figures 3 and 4  
from the outer edge of the cast iron stove top. Measure  
rear clearances from the outermost surface of the steel  
rear skirt.  
The Stardance heater is approved for installation into  
an alcove constructed of combustible materials to the  
dimensions and clearances shown on the next page.  
The same clearances apply in a standard parallel instal-  
lation.  
�
�������  
��������������  
������������  
Warning:  
• Always maintain required clearances  
(air spaces) to nearby combustibles to prevent  
fire hazard. Do not fill air spaces with insula-  
tion. All venting components must maintain a  
1” (25 mm) clearance to combustible materials.  
Maintain a 6” (150 mm) clearance when using a  
single wall pipe.  
������������������  
�������������  
��������������������  
���������������  
Locating the Stove  
In choosing a location for the stove, consider:  
• The gas appliance and vent system must be  
vented directly to the outside of the building  
and never be attached to a chimney serving a  
separate solid fuel or gas-burning appliance.  
Each direct vent appliance must use its own  
separate vent system. Common vents are pro-  
hibited.  
•
•
•
•
The location of outside walls;  
Where additional heat is needed:  
Where family members gather most often;  
The vent system requirements.  
NOTE: We do not recommend the use of wallpaper  
next to this stove. Over time, radiant heat may cause  
the wallpaper to shrink, or may adversely affect the  
binders in the wallpaper adhesive.  
• Refer to the manufacturer’s instructions in-  
cluded with the venting system for complete  
installation procedures.  
20012734  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Parallel Installation: Minimum Clearance  
and Flue Centerline, Direct Vent and  
Wall Centerline from Floor  
Direct Vent Only  
Natural Vent  
C
L
C
A
D
A
C
L
B
ST131b  
ST128b  
Effective Minimum  
Stove Clearances:  
Pipe Centerlines:  
A: 4” (102 mm)  
B: 4” (102 mm)  
C: 15¹⁄₂” (395 mm)  
D: 9” (229 mm)  
Wall Thimble  
Centerline  
56” (1480 mm) (CFM Pipe)  
52” (1378 mm) (Simpson Duravent Pipe)  
Fig. 5 Minimum wall thimble centerline.  
Fig. 3 Parallel installation, minimum back and side clear-  
ances, and flue centerlines.  
Wall and Ceiling Clearances  
Corner Installation:  
D
Minimum Clearance and Flue Centerline,  
Direct Vent and Natural Vent  
B
B
C
A
A
B
ST101b  
A: Rear Wall  
4” (102 mm)  
B: Min. Clearance  
C: Min. Alcove Height  
D: Max. Alcove Depth  
Sidewall Clearance  
45¹⁄₄” (1154 mm)*  
72” (1830 mm)  
48” (1220 mm)  
4” (102 mm)  
A
ST129b  
Fig. 6 Dimensions and clearances to ceiling or alcove.  
Stove Clearance: A: 4” (102 mm)  
Hearth Requirements  
Pipe Centerline:  
B: 14¹⁄₂” (370 mm)  
The Stardance Heater must be installed on rigid floor-  
ing. When the heater is installed directly on any com-  
bustible surface other than wood flooring, a metal or  
wood panel extending the full width and depth of the  
unit must be used as the hearth. There are no other  
hearth requirements.  
Fig. 4 Corner installation, minimum corner clearance and flue  
centerline.  
20012734  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Gas Specifications  
Horizontal Termination -  
Direct Vent ONLY  
Max.  
Min.  
Input Input  
BTU/h BTU/h  
28,000 20,000  
28,000 20,000  
The vent must rise vertically a minimum of 24” (610mm)  
off the top of the unit, before the first elbow. The hori-  
zontal run may extend up to 20’ (6m) and include a  
vertical rise of up to 40’ (12m). (Fig. 7) Horizontal  
termination must also meet the criteria shown in Figures  
9 through 11.  
Model  
Fuel  
Nat  
Prop  
Gas Control  
Millivolt  
SDDVT Series  
SDDVT Series  
SDDVTC Series  
Millivolt  
Nat Comfort Control 28,000 22,000  
SDDVTC Series Prop Comfort Control 28,000 22,000  
Air Shutter Setting  
Minimum rear injector air inlet openings.  
• Approved vent systems must terminate above and  
including the heavy line in Figure 7.  
Model  
Direct Vent  
Natural Vent  
Natural Gas  
1/2” Open  
1/2” Open  
LP  
1/2” Open  
1/2” Open  
• Two 45˚ elbows may be substituted for each single  
90˚ elbow.  
• With a rise between 2’ - 5’, one 90˚ or two 45˚ el-  
bows may be used.  
Weight: Fully assembled; 202 lbs.  
Gas Inlet and Manifold Pressures  
40  
39  
Natural  
5.5” w.c.  
14.0” w.c.  
3.5” w.c.  
LP (Propane)  
Inlet Minimum  
11.0” w.c.  
14.0” w.c.  
10” w.c.  
38  
37  
Inlet Maximum  
Manifold Pressure  
36  
35  
34  
33  
Stardance Direct Vent / Natural Vent  
Certified to:  
ANSI Z21.88-2005 / CSA 2.33-2005  
Vented Gas Fireplace Heaters  
May use up to  
three 90° Elbows  
32  
31  
30  
29  
28  
27  
26  
25  
The installation of your Vermont Castings stove must  
conform with local codes, or in the absence of local  
codes, with the National Fuel Gas Code ANSI Z223.1/  
NFPA 54 - latest edition, or CSA B149.1 Installation  
code. (EXCEPTION: Do not derate this appliance for  
altitude up to 4,500 feet (1,370m). Maintain the mani-  
fold pressure at 3.5” w.c. for Natural Gas and 10.0”  
w.c. for LP Gas.  
24  
23  
22  
21  
20  
19  
18  
16  
15  
14  
13  
12  
11  
10  
9
High Elevations  
Input ratings are shown in BTU per hour and are cer-  
tified without deration for elevations up to 4,500 feet  
(1,370m) above sea level.  
For elevations above 4,500 feet (1,370m) in USA,  
installations must be in accordance with the current  
ANSI Z223.1/NFPA 54 and/or local codes having  
jurisdiction.  
8
7
6
5
4
3
One 90°  
Elbow  
In Canada, please consult provincial and/or local au-  
thorities having jurisdiction for installations at eleva-  
tions above 4,500 feet (1,370m).  
Unacceptable  
Venting Configureation  
2
1
0
WARNING: Improper installation, adjustment,  
alteration, service or maintenance can cause in-  
jury or property damage. Refer to this manual for  
correct installation and operational procedures.  
For assistance or additional information consult  
a qualified installer, service agency, or the gas  
supplier.  
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20  
Horizontal Run (in feet)  
ST134a  
Fig. 7 Horizontal vent termination window.  
20012734  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Restrictor Plate Adjustment  
for Extended Pipe Runs  
Vertical Termination - Direct Vent ONLY  
A vertical vent system must terminate no less than 8’  
(2.44m) and no more than 40’ (12m) above the appli-  
ance flue collar. A restrictor plate (supplied) must be  
used where specified in all vertically terminated vent  
systems. (Fig. 8) NOTE: The restrictor plate supplied  
with the vertical termination should be discarded.  
Adjust the restrictor plate according to recom-  
mendations in Figure 10. A vertically terminated vent  
system must also conform to the following criteria:  
The Stardance stove is shipped with a restrictor plate  
in the Parts Bag. Adjustments can be made by loosen-  
ing the adjustment screw to allow the restrictor plate to  
slide up or down. (Fig. 9) A guide for usage is shown in  
Figure 10.  
NOTE: Some installations may require some adjust-  
ment by the installer for optimum flame appearance.  
Optimum flame appearance is a flame that is not sub-  
ject to tall, dirty yellow flames producing soot or flames  
lifting off of the ember bed ports.  
• No more than three 90˚ elbows may be used.  
• Two 45˚ elbows may be substituted for one 90˚ el-  
bow. No more than six elbows may be used.  
Restrictor Plate Adjustment  
• Vent must rise a minimum of 2 feet before offset is  
used.  
1. Remove the logs if installed.  
2. Remove the adjustment screw in the back wall of the  
firebox.  
• Termination height must conform to roof clearance  
as specified in Figure 9.  
3. Install restrictor plate as shown in Figure 9 with  
angle on plate on the top right side. Secure with  
adjustment screw.  
��  
��  
��  
��  
4. Adjust restrictor according to examples in Figure 10.  
5. Install logs following log installation instructions.  
All Vertical Termina-  
tions in this area  
��  
��  
Require use of the  
��  
��  
Restrictor Plate*  
��  
Restrictor Plate  
��  
��  
��  
��  
��  
��  
��  
Vertical Terminations  
must be within this  
area  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
�
ST936  
Unacceptable Venting  
Configuration  
Fig. 9 SDDVT/SDDVTC restrictor plate.  
�
Examples for Extended Run/Restrictor Plate Settings  
1. Vertical 40’ (12 m) - restrictor plate lowered completely  
down  
�
No Restrictor  
Plate  
�
�
2. Vertical 20’ (6 m), 90° elbow, 8’ (2.4 m ) horizontal -  
restrictor plate lowered completely down  
���  
���  
�
3. Vertical 10’ (3 m), 90° elbow, 2’ (305 mm) horizontal  
- restrictor plate lowered completely down  
�
�
Figure 10  
��  
�
�
�
�
�
�
�
�
�
�� �� �� �� �� �� �� �� �� ��  
ST132b  
Horizontal Run (in feet)  
Fig. 8 Vertical vent termination window.  
*The restrictor Plate is used on Direct Vent Installations  
Only.  
20012734  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Vent Termination Clearances  
When planning the installation, consider the location  
of the vent terminal and clearances. Some of the most  
common clearances to keep in mind are shown in  
Figure 11.  
Your stove is approved to be vented either through the  
side wall, or vertical through the roof.  
• CFM Corporation does not require any opening for  
inspection of vent pipe.  
Important: All vent clearances must be maintained.  
Check your vent termination clearances against  
Figures 11 through 13.  
• Only CFM Corporation and Simpson DuraVent vent-  
ing components specifically approved and labelled  
for this stove may be used.  
The vent should be placed so that people cannot be  
burned by accidentally touching the vent surfaces when  
the stove is operating.  
• Minimum clearances between vent pipes and com-  
bustible materials is one (1”) inch (25 mm), except  
where stated otherwise.  
The vent termination should be located where it cannot  
be damaged by such things as automobile doors, lawn  
mowers or snowblowers and it should be located away  
from areas where it could become blocked by snow,  
etc.  
• Venting terminals shall not be recessed into a wall or  
siding.  
• Horizontal venting must be installed on a level plane  
without an inclining or declining slope.  
There must not be any obstruction such as bushes,  
garden sheds, fences, decks or utility buildings within  
24” from the front of the termination hood.  
Some considerations are:  
• Obstructions or impediments to venting.  
• Nearby combustible materials that could come into  
contact with combustion exhaust gases.  
Do not locate termination hood where excessive snow  
or ice build up may occur. Be sure to check vent termi-  
nation area after snow falls, and clear to prevent ac-  
cidental blockage of venting system. When using snow  
blowers, make sure snow is not directed towards vent  
termination area.  
• Other nearby openings {within 12” (305 mm)}  
through which exhaust gas could reenter the build-  
ing.  
• All vegetation within 3’ (76 mm) that may interfere  
with the draft.  
Location of Vent Termination  
Other factors that influence where the installation will  
be sited include the location of outside walls, where  
additional heat may be desired in the home, where the  
family members gather most regularly, and perhaps  
most importantly, the distance limitations of the venting  
system.  
It is imperative the vent termination be located observ-  
ing the minimum clearances as shown on this page.  
IMPORTANT  
Direct Vent Only  
• The horizontal termination must not be recessed  
into the exterior wall or siding.  
• Horizontal vent runs must be level toward the vent  
termination.  
• Clearances around the vent termination must be  
maintained.  
• For installations using Simpson DuraVent pipe,  
parallel installations with minimum wall clearance  
have restricted access for connecting the Hori-  
zontal Vent Cap straps to the vent pipe. See the  
maker’s instructions for recommended installation  
procedures.  
20012734  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
General Venting Information - Termination Location  
INSIDE  
CORNER DETAIL  
G
V
N
H
N
A
D
E
B
V
L
C
B
B
�����  
������  
V
V
B
V
V
Fixed  
Operable  
Closed  
F
B
M
V
J
X
B
I
K
X
V
A
CFM145a  
AREA WHERE TERMINAL IS NOT PERMITTED  
VENT TERMINATION  
X
AIR SUPPLY INLET  
V
Canadian Installations1  
12” (30cm)  
US Installations2  
12” (30cm)  
A = Clearance above grade, veranda, porch,  
deck, or balcony  
B = Clearance to window or door that may be  
opened  
6” (15cm) for appliances  
6” (15cm) for appliances  
< 10,000 Btuh (3kW), 9”  
(23cm) for appliances > 10,000  
Btuh (3kW) and < 50,000 Btuh  
(15kW), 12” (30cm) for  
< 10,000Btuh (3kW), 12” (30cm)  
for appliances > 10,000 Btuh (3kW) and  
< 100,000 Btuh (30kW), 36” (91cm)  
for appliances > 100,000 Btuh (30kW)  
appliances > 50,000 Btuh (15kW)  
C = Clearance to permanently closed window  
12” (305mm) recommended to  
prevent window condensation  
12” (305mm) recommended to  
prevent window condensation  
D = Vertical clearance to ventilated soffit located  
above the terminal within a horizontal  
distance of 2’ (610mm) from the center  
line of the terminal  
18” (458mm)  
18” (458mm)  
E = Clearance to unventilated soffit  
F = Clearance to outside corner  
G = Clearance to inside corner (see next page)  
12” (305mm)  
see next page  
see next page  
12” (305mm)  
see next page  
see next page  
H = Clearance to each inside of center line  
extended above meter/regulator assembly  
3’ (91cm) within a height of 15’ (5m)  
above the meter/regulator assembly  
3’ (91cm) within a height of 15’  
(5m) above the meter/regulator  
assy  
I = Clearance to service regulator vent outlet  
3’ (91cm)  
3’ (91cm)  
J = Clearance to nonmechanical air supply inlet 6” (15cm) for appliances < 10,000  
to building or the combustion air inlet to any Btuh (3kW), 12” (30cm) for  
6” (15cm) for appliances  
< 10,000 Btuh (3kW), 9”  
(23cm) for appliances > 10,000  
Btuh (3kW) and < 50,000 Btuh  
(15kW), 12” (30cm) for  
other appliances  
appliances > 10,000 Btuh (3kW) and  
< 100,000 Btuh (30kW), 36” (91cm)  
for appliances > 100,000 Btuh (30kW)  
appliances > 50,000 Btuh (15kW)  
K = Clearance to a mechanical air supply inlet  
6’ (1.83m)  
3’ (91cm) above if within 10  
feet (3m) horizontally  
L = Clearance above paved sidewalk or paved 7’ (2.13m)†  
driveway located on public property  
7’ (2.13m)†  
M = Clearance under veranda, porch, deck or  
balcony  
12” (30cm)‡  
12” (30cm)‡  
N = Clearance above a roof shall extend a minimum of 24” (610mm) above the highest point when it passes through the roof  
surface, and any other obstruction within a horizontal distance of 18” (450mm).  
1 In accordance with the current CSA-B149 Installation Codes  
2 In accordance with the current ANSI Z223.1/NFPA 54 National Fuel Gas Codes  
† A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and  
serves both dwellings  
‡ only permitted if veranda, porch, deck or balcony is fully open on a minimum 2 sides beneath the floor:  
NOTE: 1. Local codes or regulations may require different clearances.  
2. The special venting system used on Direct Vent units are certified as part of the appliance, with clearances tested and  
approved by the listing agency.  
3. CFM Corporation assumes no responsibility for the improper performance of the appliance when the venting system does not  
meet these requirements.  
Fig. 11 Vent termination clearances.  
20012734  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Termination Clearances  
Termination clearances for buildings with combustible and noncombustible exteriors.  
Inside Corner  
Alcove Applications*  
Outside Corner  
D
C
C
F =  
Combustible  
6" (152 mm)  
G =  
Combustible  
6" (152 mm)  
V
G
V
Noncombustible  
2" (51 mm)  
V
E
Noncombustible  
2" (51 mm)  
O
F
Balcony -  
with no side wall  
Balcony -  
with perpendicular side wall  
E = Min. 6” (152 mm) for  
non-vinyl sidewalls  
Min. 12” (305 mm) for  
vinyl sidewalls  
O = 8’ (2.4 m) Min.  
M
No.  
of Caps  
M
V
DMin.  
CMax.  
V
1
2
3
4
3’ (914 mm) 2 x DActual  
P
6’ (1.8 m)  
9’ (2.7 m)  
12’ (3.7 m)  
1 x DActual  
2/3 x DActual  
1/2 x DActual  
Combustible &  
Noncombustible  
M =  
Combustible &  
Noncombustible  
12" (305 mm)  
M = 24" (610 mm)  
P = 20” (508 mm)  
DMin. = # of Termination caps x 3  
CMax. = (2 / # termination caps) x DActual  
584-15  
*NOTE: Termination in an alcove space (spaces open only on one side and with an overhang) is permitted with the dimensions  
specified for vinyl or non-vinyl siding and soffits. 1. There must be a 3’ (914 mm) minimum between termination caps. 2. All  
mechanical air intakes within 10’ (1 m) of a termination cap must be a minimum of 3’ (914 mm) below the termination cap. 3. All  
gravity air intakes within 3’ (914 mm) of a termination cap must be a minimum of 1’ (305 mm) below the termination cap.  
Fig. 12 Termination clearances.  
Venting Requirements - Natural Vent Only  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
��  
�
Venting Runs  
A
NOTE: When venting staight vertical, without any  
B
elbow, a minimum of 8 ft. vertical is required  
off the top of the stove.  
= Acceptable venting configuration  
= Unacceptable venting configuration  
A: Vertical installations up to 36 feet (12m) in  
height. Up to an 18 ft. horizontal vent run can be  
installed within the vent system using a  
maximum of two 90-degree elbows or four  
45-degree elbows.  
B: Vertical installations up to 36 feet (12m) in  
height. Up to a 24 ft. horizontal vent run can be  
installed within the vent system using a  
maximum of two 45-degree elbows.  
(Ratio = 2/3, Hor./Vert.)  
�
�
�
������������������������������������������������������  
Horizontal Run (in feet)  
NOTE: When using the FSDHAG, the restrictor plate  
supplied with the stove is not used.  
Fig. 13 Vent termination window - Natural Vent ONLY.  
20012734  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Selkirk Corporation Vent Components  
www.selkirkcorp.com  
1301 W. President George Bush Highway Ste. 330  
Richardson, TX 75080  
Venting Requirements and Options -  
Direct Vent ONLY  
Approved Vent System Components  
Phone: 1-800-992-8368, Fax: 1-877-393-4145  
The Stardance Heater must be vented to the outdoors  
through an adjacent exterior wall or through the roof.  
The venting system must be comprised of the appropri-  
ate listed venting components specified on this page.  
These parts are available from DuraVent Corporation,  
Selkirk Corporation or your Vermont Castings Dealer.  
See Figure 4 for dimensions relevant to the standard  
minimum-vent kits.  
Appliance Adapter  
90° Elbow, Blk.  
45° Elbow, Blk.  
6” Straight, Blk.  
9” Straight, Blk.  
4” - 10” Adjustable Straight Section Blk.  
12” Straight, Blk.  
18” Straight, Blk.  
24” Straight, Blk.  
36” Straight, Blk.  
4DT-AAV  
4DT-EL90B  
4DT-EL45B  
4DT-06B  
4DT-09B  
4DT-AJ12B  
4DT-12B  
4DT-18B  
4DT-24B  
4DT-36B  
4DT-48B  
4DT-HC  
Simpson DuraVent Components  
www.duravent.com  
Phone: 1-800-835-4429, Fax: 1-707-446-4740  
48” Straight, Blk.  
Horizontal Termination  
Wall Thimble  
Minimum Horizontal Vent Kit  
2792  
4DT-WT  
Starter Pipe Assembly (incl. inner & outer sections)  
2768*  
Vinyl Siding Standoff  
Snorkel Termination - 14”  
Snorkel Termination - 36”  
Wall Support Band  
Cathedral Ceiling Support Box  
Storm Collar  
4DT-VS  
90° Elbow, Blk.  
45° Elbow, Gal.  
6” Straight, Blk.  
9” Straight, Blk.  
11” - 14⁵⁄₈” Adjustable Straight Section  
12” Straight  
46DVA-E90B*  
46DVA-E45  
46DVA-06B*  
46DVA-09B  
46DVA-08AB  
46DVA-12  
4DT-ST14  
4DT-ST36  
4DT-WS/B  
4DT-CCS  
4DT-SC  
Firestop Spacer  
4DT-FS  
24” Straight  
36” Straight  
48” Straight  
46DVA-24B*  
46DVA-36B  
46DVA-48  
Flashing 0/12 - 6/12  
Flashing 6/12 - 12/12  
Steel Chimney  
4DT-AF6  
4DT-AF12  
Horizontal Vent Cap  
Wall Plate  
Vinyl Siding Shield  
Snorkel Termination - 14”  
Snorkel Termination - 36”  
Wall Strap  
46DVA-HC*  
46DVA-DC  
46DVA-VSS  
46DVA-SNK14  
46DVA-SNK30  
46DVA-WS  
46DVA-CS  
Horizontal Kit A  
Horizontal Kit B  
Vertical Kit  
Masonry Chimney Kit  
Vertical Termination Cap  
4DT-HKA  
4DT-HKB  
4DT-VKC  
4DT-MCK  
4DT-VC  
Cathedral Ceiling Support Box  
Storm Collar  
46DVA-SC  
Firestop Spacer  
46DVA-FS  
Flashing 0/12 - 6/12  
Flashing 6/12 - 12/12  
Steel Chimney Conversion Kit  
Kit A (6⁵⁄₈” - 8⁵⁄₈”)  
Kit B (6⁵⁄₈” - 10¹⁄₂”)  
Kit C (6⁵⁄₈” - 13”)  
46DVA-F6  
46DVA-F12  
46DVA-KCA  
46DVA-KCB  
46DVA-KCC  
46DVA-KMC  
46DVA-VCH  
Masonry Chimney Conversion Kit  
Vertical Termination Cap (High Wind)  
Vertical Termination Cap (Low Profile)  
46DVA-VC  
*Included in Minimum Horizontal Vent Kit #2792  
All DuraVent Straight vent pipe sections have a net  
length 1¹⁄₂” (37mm) less than the nominal dimension;  
i.e., a 6” (152mm) Straight pipe section has an effective  
length of 4¹⁄₂” (115mm).  
NOTE: Direct vent pipe may be used on the Natural  
Vent system from the top of the draft hood adapter to  
the ceiling.  
20012734  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
CFM Vent Components  
Twist Lock 12” Straight Pipe (CG)  
(1) 12” Non-adjustable Pipe  
Twist Lock 12”-18” Straight Pipe (CG)  
(1) 12” - 18” Adjustable Pipe  
Twist Lock 24” Straight Pipe (CG)  
(1) 24” Non-adjustable Pipe  
Twist Lock 48” Straight Pipe (CG)  
(1) 48” Nonadjustable Pipe  
Twist Lock 45-Degree Elbow (CG)  
for vertical offsets  
7TFSDVP12  
7TFSDVP1218  
7TFSDVP24  
7TFSDVP48  
7TFSDVT45  
The following kits are available to meet the needs of  
most installations. All pipe has a 7” outer diameter and  
includes a 4” diameter inner section. A (CG) designa-  
tion indicates the part is finished in Charcoal Gray paint.  
Consult your dealer about other vent parts that may be  
appropriate to complete the installation.  
Min. Through the Wall Vent Kit  
(1) 90-Degree Elbow (CG)  
7TFSSK  
(1) 24” Straight pipe (CG)  
(1) 45-degree Elbow  
(1) 24” - 42” Adjustable Straight Pipe  
(1) Side Wall Termination  
Draft Hood Adapter  
NV Stove Kit  
FSDHAG  
7FSSK  
(1) Firestop  
(1) Zero-clearance sleeve  
(1) Hardware package  
(1) Finishing plate (CG)  
(1) 7” Diameter Polished Brass Trim Ring  
(1) 48” Nonadjustable Pipe (CG)  
(1) 24” Nonadjustable Pipe (CG)  
(1) Finishing Plate  
(1) Finishing collar (CG)  
(1) Finishing Collar (CG)  
(4) Charcoal Gray flue pipe rings  
Starter Kit for Below Grade Installation  
(1) Snorkel Termination (7TDVSNORK)  
Vertical Termination Kit, 1/12-6/12 Pitch  
(1) Combination Horizontal Offset / Roof Support  
(1) Vertical Termination  
(1) Storm Collar  
(1) 1/12-6/12 Flashing  
(1) Finishing Plate (CG)  
(1) 90 Degree Elbow (CG)  
Stove Kit  
Includes all parts in the 7FSSK plus the Draft Hood Adapter  
FSDHAG  
Combination Offset/Roof Support  
Attic Insulation Shield  
7” Charcoal Gray Pipe Rings, (4)  
7” Polished Brass Pipe Rings (4)  
Wall Thimble  
7TDVSKS  
7FSDHASK  
7TDVSKVA  
7DVCS  
7DVAIS  
7FSDRG  
7FSDRP  
942G  
(1) Finishing Collar (CG)  
(1) Polished Brass Flue Pipe Ring  
(1) Hardware Package  
Vertical Termination Kit, 7/12-12/12 Pitch  
(1) 7/12 - 12/12 Flashing  
and all of the other Vertical Termination parts.  
Vertical Termination, Flat Roof  
(1) Flat Flashing  
7TDVSKVB  
7DVSKVF  
and all of the other Vertical Termination parts.  
NOTE: Direct vent pipe may be used on the Natural  
Vent system from the top of the draft hood adapter to  
the ceiling.  
20012734  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
4. The rheostat control switch attaches to the left side  
of the valve bracket at the front of the stove. (Fig. 17)  
Install the Optional Fan  
If you are installing the optional convection Fan Kit  
#2767 (FK26), continue here. If you are not installing a  
Fan Kit, go to Page 16, Venting System Assembly.  
1. The fan kit includes a Blower Assembly and a Rheo-  
stat Assembly, connected by a cable. (Fig. 14) The  
Blower Assembly mounts to the bottom rear of the  
stove, and the Rheostat mounts to the valve bracket  
to the left of the valve. The assembly includes a  
‘snapstat’ which automatically turns the fan On (or  
Off) above (or below) approximately 109˚. The Rheo-  
stat also provides a range of fan speed settings from  
Off (which overrides the snapstat function) to High.  
Unpack and inspect the Blower assembly. Confirm  
the fan spins freely.  
• Remove retaining nut from shaft of rheostat. (if  
preinstalled)  
• Insert the rheostat through the hole in the back  
of the left side of the valve bracket, aligning the  
locator pin with the smaller hole in that bracket.  
• Thread the retaining nut onto the shaft of the  
rheostat, tightening with a wrench. Do not over-  
tighten.  
• Attach the control knob to the rheostat shaft.  
• Use the wire tie to secure the fan and rheostat  
wire harnesses together.  
Rear Skirt  
WARNING  
This appliance is equipped with a three-prong  
(grounded) plug for your protection against shock  
hazard and should be plugged directly into a prop-  
erly grounded three-prong receptacle. Do not cut or  
remove the grounding prong from this plug.  
Sheet Metal  
Screws  
Snapstat Bracket  
Not Used on RF Models  
Snapstat/  
Extension  
Assembly  
Rear Skirt  
ST313  
Insert  
Not Used on  
Stardance  
Fig. 15 Remove rear skirt insert.  
Rheostat  
Assembly  
Star Washer  
Sheet Metal Screws  
2
Snapstat  
1
Phillips  
Pan Head  
Bolts  
1/4” - 20  
Hex Bolt  
Not Used  
on RF  
Models  
Star  
Washer  
Blower  
Snapstat  
Bracket  
Assembly  
Connect to PC Board on  
RF Models Only  
3
ST473  
Fig. 14 Fan kit components.  
NOTE: Shown  
without shell for  
clarification  
2. Remove the rear skirt insert panel at the bottom of  
the Rear Skirt (Fig. 15) and fasten the blower assem-  
bly to the firebox back with the two Phillips pan-head  
bolts originally installed in the firebox back. (‘1’, Fig.  
16)  
ST314  
Fig. 16 Attach the fan assembly and the snapstat.  
NOTE: Steps 3 and 4 do not apply when the RF  
valve is used. After attaching blower assembly to the  
firebox, run the spliced female leads to the front of  
the stove and attach to back of RF valve. (Page 34,  
Fig. 58)  
3. Attach the snapstat assembly to the snapstat bracket  
with two sheet-metal screws. (‘2’, Fig. 16) Attach the  
snapstat bracket to the stove with a hex-head bolt  
passing through the bracket and into the stove base.  
(‘3’, Fig. 16)  
Rheostat Retaining  
Collar  
Rheostat Knob  
ST347a  
Fig. 17 Attach the fan rheostat.  
20012734  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Venting System Assemlby - Direct Vent  
General Information  
The Stardance is approved for installation only with the  
vent components listed on Pages 13 & 14. Follow the  
vent component instructions exactly.  
CEMENT  
For U.S. installations: The venting system must con-  
form with local codes and/or the current National Fuel  
Gas Code, ANSI Z223.1/NFPA 54.  
For Canadian installations: The venting system must  
conform to the current CSA B149.1 installation code.  
Install the Vent Adapter Pipe  
ST212a  
(CFM Corporation Vent Components)  
Fig. 19 Attach inner assembly to flue collar.  
1. Attach Inner Starter Pipe, (found in the parts  
bag), to the next section of inner pipe.  
• Run a bead of sealant about 1/2” from the upper  
end of the Inner starter pipe and join the two sections  
together.  
• Drill three pilot holes into the Inner Starter and  
secure the assembly with three sheet metal screws.  
(Fig. 18)  
First Section of Vent  
Pipe  
#8 x 1/2” Sheet  
Metal Screws  
ST213  
3” Inner  
Fig. 20 Fasten outer pipe with #12 x 1/2” sheet metal screw.  
Starter PIpe  
Install the Vent Adapter Pipe  
ST211  
(Simpson Dura-Vent Components)  
Fig. 18 Connect the inner starter with the next section of in-  
ner vent pipe.  
1. Discard the inner starter pipe shipped with the  
stove. Using the starter pipe assembly listed on  
Page 7, slide the inner section out to allow access.  
2. Dry fit the Inner Pipe assembly to the stove for  
the purpose of determining the center line of the  
pipe on the wall.  
• Run a bead of sealant around the bottom end of  
the starter pipe and attach the assembly to the stove  
using three 1/4-20 x 3/8” Phillips screws provided in  
the parts bag. (Fig. 21)  
• Side Wall Terminations: Dry fit the outer elbow  
with the vertical outer vent and confirm the centerline  
alignment with the wall thimble opening.  
3. Attach the Inner Vent Assembly to the stove.  
• Run a bead of sealant around the bottom end of  
the starter pipe and attach the assembly to the stove  
using three 1/4-20 x 3/8” Phillips screws provided in  
the parts bag. (Fig. 19)  
4. Install the Outer Adapter Pipe. Apply a 1/4” bead  
of cement around the inside wall of the pipe, about  
1” from the end. Insert the pipe over the stove flue  
collar, keeping the vertical seam oriented to the back  
of the stove. Also, be sure to align holes on the pipe  
with the holes on the flue collar of the firebox. Fasten  
the pipe to the holes in the flue collar with the #12 x  
1/2” sheet metal screws provided. (Fig. 20)  
2. Install the Outer Adapter Pipe. Apply a 1/4” bead of  
cement around the outside surface, about one inch  
from the crimped end. (Fig. 22) Orient the vertical  
seam to the rear, and insert the crimped end of the  
outer pipe into the flue collar. Fasten with three sheet  
metal screws provided.  
20012734  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Secure with a minimum of two #8 x 1/4” sheet metal  
screws and seal with hi-temp silicone.  
Inner Adapter  
Pipe  
1/4-20 x  
3/8 Phillips  
Screws  
For units factory equipped with appliance adapters from  
other brands of Direct Vent systems, it is permissible  
to simply slide a length of DT pipe over the appliance  
adapter. Secure with a minimum of two #8 x 1/4” sheet  
metal screws and seal with hi-temp silicone.  
CEMENT  
Side Wall Termination Assembly  
1. Locate the vent opening on the wall. Refer to Page  
7, Figure 6, to determine the opening centerline.  
It may be necessary to first position the stove and  
measure to find the hole location. Depending on  
whether the wall is made of combustible materials,  
cut the opening to the size shown in Figure 24. Com-  
bustible wall openings must be framed as shown in  
Figure 23.  
ST355b  
Fig. 21 Simpson Dura-Vent - install inner adapter pipe.  
CFM System  
9³⁄₈”  
(240mm)  
9³⁄₈”  
(240mm)  
Combustible Wall  
10”  
DuraVent  
System  
Framing Detail  
(254 mm)  
ST356a  
Fig. 22 Simpson Dura-Vent - install outer adapter pipe.  
7¹⁄₂”  
(191 mm)  
Install Vent Adapter Pipe  
(Selkirk Corporation Vent Components)  
Noncombustible Wall  
VO584-100  
The appliance adapter (AA) adapts DIRECT-TEMP to  
most direct vent appliances incorporating outlet col-  
lars configured to receive most common 4” (ID) by 6⁵⁄₈”  
(OD) or 5” (ID) by 8” (OD) “Twist Lock” style, direct vent  
systems.  
Fig. 23 Locate vent opening.  
2. Measure the wall thickness and cut the wall sleeve  
sections to proper length (MAXIMUM 12”). Assemble  
the sleeve with the #8 sheet metal screws supplied.  
Attach the firestop plate to the sleeve end with the  
holes. (Fig. 24) NOTE: The wall sleeve is required  
in combustible walls only.  
The adapter incorporates two indentations on the outer  
wall of the inlet end, which are designed to “Twist Lock”  
into place upon attachment to the appliance outlet. Align  
the adapter indentations with the entry slots of the appli-  
ance outlet and slide together. Turn the adapter clock-  
wise approximately one-quarter turn to lock in place.  
The outlet end of the adapter is standard DIRECT-  
TEMP construction.  
3. Install the Wall Firestop/Sleeve assembly into the  
wall cutout and fasten the firestop to the wall cutout  
framing members. (Fig. 24)  
For DuraVent pipe only: Install vent pipe by aligning  
the locking system together, sliding the pipes togeth-  
er and twisting clockwise.  
For connection of Direct-Temp to units with 4” x 7” flue  
outlets, the following methods have been approved:  
• Install 90° elbow. Twist lock as before.  
• Slide the wall plate over horizontal run before at-  
taching the horizontal run to the elbow. Fasten wall  
plate to wall.  
• Install the Universal/Napoleon Appliance Adapter  
4DT-AAN.  
• Connect a standard Direct-Temp pipe length (do  
not use an adjustable length in this application) a  
minimum of 1¹⁄₂” over the flue outlet. The outside of  
the Direct-Temp Length will fit inside the flue outlet  
4. For CFM Vent Pipe only: If necessary, measure  
to determine the vertical length (X) of pipe required  
from the adapter pipe to the wall cutout centerline,  
20012734  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
12”  
(305 mm)  
Max. Length  
Sleeve  
X
#8 Sheet  
Metal Screws  
ST215  
Fig. 26 Measure the horizontal length.  
sheet metal screws. Slide the trim collar up against  
the wall plate to cover the screws. (Fig. 27)  
10. For both CFM and DuraVent Systems: Install  
the vent terminal. (Fig. 28) Apply high temperature  
sealant one inch from the ends of the inner and outer  
collars. Guide the inner and outer vent termination  
collars into the adjacent pipes. Double check that  
the vent pipes overlap the collars by 2”. Fasten the  
termination to the wall with the screws provided, and  
caulk the joint with weatherproof sealant.  
Firestop  
ZCS103  
Fig. 24 Assemble the wall sleeve and firestop.  
including a 2” overlap at the joint. (Fig. 25) use a  
hacksaw or tin snips to trim the pipe as needed.  
5. Install first the inner then the outer straight pipe  
section(s), trimmed end down, to the point of the el-  
bow. Drill 3 holes through each joint and fasten with  
sheet metal screws.  
11. For CFM only: Install Charcoal Gray Pipe Rings  
(#7FSDRG) or Polished Brass Pipe Rings (#7FS-  
DRP) at pipe joints, if desired.  
Trim Collar  
Wall  
Sleeve  
X
Wall Plate  
ST216  
Fig. 27 Install the horizontal pipe and wall plate parts.  
Seal Both Ter-  
minal Ends  
ST214a  
Fig. 25 Determine the vertical pipe length.  
6. Seal and install the elbow using 3 sheet metal  
screws at each joint.  
7. Measure, and cut if needed, the appropriate length of  
pipe section needed to make the connection through  
the wall. Include a 2” overlap; i.e. from the elbow  
to the outside wall face, about 2” or the distance  
required if installing a second 90° elbow. (Fig. 26)  
8. Slip the wall plate and trim collar over the interior end  
of the horizontal pipe and install into the wall sleeve.  
Seal the joint inside the wall plate if needed to keep  
cold air from being drawn into the home.  
Caulk Plate Joint with  
Weatherproof Sealant  
ST217  
Fig. 28 Install the vent terminal.  
9. Seal the ends and connect the horizontal pipe to the  
elbow. Fasten the wall plate to the pipe with three  
20012734  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Recessed Wall  
Vent Termination Below Grade  
Install Snorkel Kit #7FSDVSKS when it is not possible  
to meet the required vent termination clearances of 12”  
(305 mm) above grade level. The snorkel kit will allow  
installation depth of down to 7” (178 mm) below grade  
level. The seven inches is measured from the center of  
the horizontal vent pipe as it penetrates the wall. If the  
venting system is installed below grade, a window  
well must be installed with adequate and proper  
drainage. (Fig. 29)  
Firestop  
Finishing Collar  
Sheet Metal  
Screws and  
Bracket  
Wall Screws and  
Anchor  
Waterproof Seal  
Around Pipe  
7” Pipe  
Wall Screws  
Wall Plate  
ST219  
Waterproof Seal  
and Anchors  
Around PIpe  
Snorkel  
Firestop  
Fig. 30 Use extension brackets to mount snorkel against  
recessed wall.  
Termination  
Cap  
Vertical (Through the Roof)  
Vent Assembly  
Note that all vertically terminated installations must  
include the restrictor plate included with the stove.  
Refer to Page 9, Figure 8.  
Drain  
Window Well  
Make certain the vent system conforms to all other  
requirements for vertical termination as specified on  
Page 8.  
This installation will require you to first determine the  
roof pitch and use the appropriate vent components.  
Refer to Pages 9 and 11, Figures 8 and 11.  
ST218a  
1. Locate the final position of the stove, observing all  
clearances for both the vent and the stove.  
Fig. 29 Snorkel kit installation.  
2. Plumb to the center of the inner (4”) flue collar from  
the ceiling above, and mark that location.  
NOTE: Be sure to maintain side wall clearances and  
vent run restrictions. Refer to Figures 5, 6, 7, and 8.  
3. Cut the opening:  
1. Establish the vent hole through the wall.  
CFM System: 9³⁄₈” x 9³⁄₈” (240 x 240mm)  
DuraVent System: 10” x 10” (254 x 254mm)  
2. Remove soil to a depth of approximately 16”  
(400mm) below the base of the snorkel. Install a  
window well (not supplied). Refill the hole with 12”  
(305mm) of coarse gravel and maintain a clearance  
of at least 4” (102 mm) below the snorkel. (Fig. 33)  
4. Plumb any additional opening through the roof or  
other construction that may be needed. In all cases,  
the opening must provide a minimum of 1” (25 mm)  
clearance to the vent pipe.  
3. Install the vent system as described on Pages 15-18.  
5. Place the stove in its final position.  
4. Be sure to make a watertight joint around the vent  
pipe joint at the inside and outside wall joints.  
6. Install firestop(s) #7DVFS and Attic Insulation Shield  
#7DVAIS as needed. (Fig. 31) If there is a room  
above ceiling level, a firestop must be installed on  
both the bottom and top sides of the ceiling joists.  
If an attic is above ceiling level, an attic insulation  
shield must be installed.  
5. Apply high temperature sealant around the inner  
and outer snorkel collars. Join the pipes and fasten  
the snorkel termination to the wall with the screws  
provided.  
6. Level the soil to maintain a 4” clearance below the  
snorkel.  
7. Install the appropriate roof support and flashing,  
making certain that the upper flange of the flashing  
base is below the shingles. (Fig. 32)  
If the foundation is recessed, use extension brackets  
(not supplied) to fasten the lower portion of the snor-  
kel. Fasten the brackets to the wall first, and then  
fasten to the snorkel with self-tapping #8 x 1/2” sheet  
metal screws. Extend the vent pipes out as far as the  
protruding wall face. (Fig. 30)  
8. Install appropriate pipe sections until the vent run  
reaches above the flashing. The enlarged ends of  
the vent sections always face downward.  
20012734  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Selkirk Direct-Temp Metalbestos Direct  
Vent System  
#7DVAIS  
Attic Insulation  
Shield  
Installation Instructions  
1. Determine whether the length of pipe fits the appli-  
ance outlet by attempting to engage the parts. If the  
parts engage smoothly, proceed to Step 2. If ob-  
structions, interference or loose fit is noted, contact  
the appliance manufacturer or Selkirk Metalbestos  
with the dimensions of the appliance outlet.  
#7DVFS  
Firestop in  
Upper Floor  
Use Four  
8dNails  
2. Slide the length of pipe over the appliance outlet a  
minimum of 1¹⁄₂” and screw to the appliance outlet  
collar using a minimum of two (2) #8 x 1/4” sheet  
metal screws.  
Appliance Adapter (AAV)  
The appliance adapter (AAV) adapts DIRECT-TEMP to  
most direct vent appliances incorporating outlet collars  
configured to receive most common 4” (ID) 6⁵⁄₈” (OD) or  
5” (ID) by 8” (OD) “Twist Lock” Style, direct vent sys-  
tems.  
#7DVFS  
Firestop in  
Ceiling  
ST222  
Fig. 31 Install firestops and attic insulation shield.  
The adapter incorporates two (2) indentations on the  
outer wall of the inlet end, which are designed to “Twist  
Lock” into place upon attachment to the appliance  
outlet. Align the adapter indentations with the entry  
slots of the appliance outlet and slide together. Turn the  
adapter clockwise approximately one-quarter turn to  
lock in place. The outlet end of the adapter is standard  
DIRECT-TEMP construction.  
Use three #5 sheet  
metal screws at  
each joint  
Sealant  
Storm Collar  
Framing Dimension Table 1  
Model DT Ceiling Support (CS) Cathedral Ceiling Wall Thimble  
Upper  
edge of  
flange  
Diameter  
Firestop (FS)  
Support CCS)  
10⁵⁄₈” x 10⁵⁄₈”  
14¹⁄₂” x 14¹⁄₂”  
(WT)  
goes under  
upper  
shingles  
4”  
5”  
8¹⁄₄” x 8¹⁄₄”  
8¹⁄₄” x 8¹⁄₄”  
10¹⁄₈” x 10¹⁄₈”  
10¹⁄₈” x 10¹⁄₈”  
Use of Sealant  
Flashing  
It is not required to apply or use sealant on the inner  
liner of DIRECT-TEMP. For outer wall joint sealing  
considerations, follow appliance manufacturer recom-  
mendations.  
#7DVSKV  
(A, B, or F)  
RoofSupport  
ST221  
Fig. 32 Roof support and flashing.  
Joint Connection:  
The pipe and elbows are assembled by inserting the  
outlet (male) end of a length of pipe or elbow into the in-  
let (female) end of an adjacent length of pipe or elbow.  
Make sure the outlet end is fully seated within the inlet  
end of the adjoining section and the gasket, located on  
the inner liner of the inlet section is fully enclosed by the  
inner liner of the outlet of the adjoining section. Push  
in the Lock Tab such that it becomes seated within the  
inward groove of the adjoining section. This locks the  
joint in place. (Fig. 33)  
9. Install the storm collar and seal around the joints.  
(Fig. 32)  
10. Add additional vent lengths to achieve the proper  
overall height.  
11. Apply cement to the inner and outer termination col-  
lars and install the terminal cap.  
20012734  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Gasket  
Outlet End  
Inlet End  
Lock Tab  
To Termination  
To Appliance  
ST922  
Fig. 33 Joint connection.  
Horizontal Termination (HC)  
Trim Plate (TP)  
(Required if Wall  
Thimble is not used)  
Vent Termination (VC)  
Storm Collar (SC)  
Pipe Length  
Wall Thimble (WT)  
(Optional)  
90° Elbow  
(EL90)  
Roof Flashing (AF)  
Pipe Length  
Ceiling Support  
(CS)  
Appliance Adapter  
(AAV)  
Trim Plate (TP)  
Pipe Length  
Horizontal Venting  
Pipe Length  
Vertical Venting  
ST925  
Appliance Adapter  
(AAV)  
Fig. 34 Selkirk Venting Components  
ST924  
20012734  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Supporting DIRECT-TEMP: Vertical Support  
Offsets:  
Vertical installations can be supported by two methods:  
If any offsets are necessary in the vertical system, an  
Offset Support (OS) should be installed directly above  
the upper elbow of the offset. Install by attaching the  
offset support band to the pipe with two #8 x 1/4” sheet  
metal screws (minimum ) and secure the offset support  
straps to surrounding structure. (Fig. 37)  
Ceiling Support (CS) (used in flat ceiling installation)  
comes with a support plate and a support collar. Install  
it by screwing the support plate to the top of the prop-  
erly framed ceiling joist opening, using screws provided.  
A round trim plate (TP) is attached to the ceiling, using  
screws, to provide a finished appearance once in-  
stalled. (Fig. 35)  
Nail to top of  
framing  
Ceiling Support  
Offset Support  
Collar  
Offset Support  
Strap  
Ceiling Support  
Collar  
Plate  
ST927  
Trim Plate  
Fig. 37 Offset support.  
ST923  
Supporting DIRECT-TEMP: Horizontal Support  
Fig. 35 Ceiling support.  
Horizontal runs of Direct-Temp should be supported  
every 4’ (122 cm) of pipe. This can be done with the use  
of plumbers strapping or the offset support.  
The Cathedral Ceiling Support (CCS) may be used in  
pitched or flat ceiling installations and comes with a  
support collar and a decorative two part square trim  
plate. Install by inserting the support box down through  
the framed joist opening (end with round hole first) in  
the ceiling using tin snips, cut the corners of the open  
end of the box such that the sides can be folded down  
over the top of the joist framing members. Nail the  
folded sides to the top of the framing. (Fig. 36)  
Adjustable Length (AJ)  
An Adjustable Length is available to accommodate  
installations where non-standard lengths are necessary.  
The adjustable length telescopes down over a standard  
length of pipe and provides an extension range of 3¹⁄₂”  
(89 mm) to 10¹⁄₂” (267 mm). Install by sliding the inlet  
end of the adjustable length over the outlet end of a  
standard length of pipe. After positioning the adjustable  
length appropriately, secure it to the standard length  
with two (2) #8 x1/4” sheet metal screws (provided).  
Seal the area between both the top and bottom of the  
adjustable length outer wall and the outer wall of the  
standard length with an approved silicone sealant.  
Two Part Square  
Trim Plate  
Support Box  
Fire Stopping  
DIRECT-TEMP must be firestopped wherever it passes  
through floors, ceiling or walls. The only location where  
a firestop is not required is at the roof level. Both verti-  
cal support components with trim plates provide for  
firestopping. The wall thimble also acts as a firestop.  
at other locations, a firestop spacer (FS) should be in-  
stalled. In the attic the firestop should be placed on top  
of the joist framing to prevent debris from falling into the  
joist framing. (Fig. 38)  
Support Box Collar  
ST926  
Fig. 36 Support box.  
A two-part square trim plate is provided to give a fin-  
ished look once installed. Simply fit the two halves of  
the trim plate around the cathedral ceiling support box  
hanging below the ceiling (overlapping if necessary)  
and screw them to the ceiling. Both the ceiling support  
and cathedral ceiling support can support a maximum  
of 40’ (12 m) of pipe.  
Horizontal Installation  
1. Determine the appliance location. Refer to the appli-  
ance manufacturer’s installation instructions for clear-  
ance to combustible requirements, termination options,  
number of elbows, maximum length, etc. Then posi-  
tion the appliance and plan vent routing accordingly.  
20012734  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
NOTE: As a general rule, the wall thimble is optional in  
the U.S. However, there may be some manufacturers  
that require it. Contact the appliance manufacturer for  
information if uncertain. When installed in Canada, a  
wall thimble is required on all installations in which  
the vent passes through a combustible wall.  
Firestop (FS)  
Placed on Top  
of Framed  
Opening  
5. If required, install the outside half of the wall thimble  
(WT) through the opening and screw or nail in place. (Fig.  
40) Seal around the perimeter of the thimble face plate on  
the exterior wall using an RTV silicone sealant to provide  
protection from possible rain infiltration. (Fig. 40)  
Maintain at Least  
Minimum Clearance to  
Combustibles, Wire and  
Attic Framing  
(No floor)  
Wall Thimble  
Shield  
Insulation  
ST928  
Fig. 38 Firestop spacer.  
Seal with RTV  
Silicone Sealant  
Consider locating the appliance in a place where there  
will be no interference with wall studs, electrical wir-  
ing, conduit, plumbing pipe or other obstructions. The  
termination should be located at least 12” (305 mm)  
(Fig. 39) above grade, remain above the snow line in  
geographical areas that accumulate snow and be away  
from traffic areas such as walkways if it is less than 7’  
(2.1 m) high. Refer to Pages 11, 12, Figures 11, 12 for  
more detail.  
Wall  
Thimble  
Shield  
on Exterior side  
here (around  
perimeter)  
Wall  
Wall Thimble  
Face Plate  
Thimble  
Face  
Snorkel Termination  
Plate  
ST930  
Fig. 40 Wall thimble.  
Window Well  
NOTE: The wall thimble accommodates wall thickness-  
es of 4¹⁄₂” (114 mm) to 7¹⁄₂” (191 mm). If a larger range  
is needed due to a thicker wall, it is permissible to field  
fabricate a metal sleeve extension and attach it to the  
shields.  
12” (305 mm) Minimum  
Clearance Above Grade Level to  
Air Intake  
Maintain 2”  
(51 mm)  
Clearance  
Below Snorkel  
Grade Level  
Sloped Away  
From Building  
6. Install the horizontal termination to the exterior wall  
using four (4) all purpose screws through the holes  
located at each corner of the termination. Make sure  
the arrow (embossed on the front of the termination)  
is pointing up. (Fig. 41) If the house has vinyl siding,  
a Vinyl Siding Standoff (VS) must be installed prior to  
installing the horizontal termination. Refer to the appli-  
ance manufacturer to determine if one is recommend-  
ed. Attach the vinyl siding standoff to the exterior side  
of the wall (making sure it is level and centered with  
respect to the opening) with screws (provided) at each  
corner of the standoff. Attach the horizontal termination  
to the standoff. (Fig. 42)  
Adequate  
Drainage as per  
Local Codes  
ST929  
Fig. 39 Below grade installation.  
2. Assemble the pipe (and elbow if using) and attach it  
to the appliance. Plan for a level to 1/4” per foot rise (6  
mm per 305 mm) (from inlet to outlet) in the horizontal  
system if not specified by the appliance manufacturer.  
Horizontal runs should be supported every 4’ (122 cm).  
If the wall is brick or concrete, and contains no com-  
bustible material, a 7” (178 mm) round penetration  
hole is adequate. The wall thimble is not required. The  
perforated straps of the horizontal termination provide  
a method of attachment. These can either be threaded  
through the opening or wall thimble (if used) and  
screwed to the pipe or removed with a pair of tin snips  
if not used. Use proper masonry fasteners to attach the  
horizontal termination to the wall.  
3. Push the appliance near the desired location. Deter-  
mine the centerpoint of the penetration by locating the  
centerline of the outlet of the pipe with respect to the wall.  
4. Frame an opening to the dimension specified in the  
Framing Dimension Table 1. Ensure the centerline of  
the pipe lines up with the center of the prepared open-  
ing unless otherwise specified by the appliance manu-  
facturer.  
20012734  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Horizontal Termination  
Vertical Termination  
Storm Collar  
Flashing  
Approved Silicone  
Sealant Here  
Offset Support  
Collar  
ST931  
Fig. 41 Horizontal termination.  
Firestop  
Spacer  
Vinyl Siding Standoff  
Ceiling  
Support  
Plate  
Horizontal Termination  
Ceiling Support Collar  
ST932  
Fig. 42 Vinyl siding standoff and horizontal termination.  
7. If a wall thimble is used, push the pipe (which is  
connected to the appliance) carefully through the wall  
thimble until the DIRECT-TEMP pipe becomes fully  
engaged with the horizontal termination. If no thimble is  
used, place the Trim Plate (TP) on the DIRECT-TEMP  
pipe. Carefully push the DIRECT-TEMP pipe through  
the wall until fully engaged with the horizontal termina-  
tion. Secure the trim plate to the wall.  
Trim Plate  
ST933  
Fig. 43 Typical vertical venting configuration.  
2. After positioning the appliance, determine where the  
vent pipe will pass through the ceiling. This can be done  
by using a plum bob or a small weight attached to a  
string. Hold the plum bob from the ceiling moving it until  
it lines up with the centerline of the outlet of the appli-  
ance. Mark the position on the ceiling.  
NOTE: If a vertical rise is necessary on the exterior side  
of the building, a 14” (356 mm) and 36” (914 mm) Snor-  
kel Termination (ST) is available. Follow the installation  
procedures for horizontal terminations. If the snorkel  
termination is to be located below grade, a window well  
is recommended with adequate and proper drainage  
as per local codes. Leave 2” (51 mm) clearance be-  
low snorkel to prevent water from entering the snorkel  
termination. Do not enclose the snorkel within a wall or  
other type of enclosure and do not back fill. Ensure  
that grade level slopes away from the building. (Fig. 39)  
NOTE: Frame openings to the dimensions specified  
in the framing table for the cathedral ceiling support  
box (CCS), the ceiling support (SC) and wherever the  
firestop spacer (FS) is being used.  
3. Cut and frame the appropriate sized square hole  
through the ceiling. Repeat the process for other ceiling  
penetrations as necessary.  
4. Determine and mark the roof penetration in the  
same manner.  
Vertical Installation (Fig. 43)  
5. Cut a hole in the roof at this point large enough to  
satisfy all clearance-to-combustible requirements as  
specified by the appliance manufacturer’s installation  
instructions.  
1. Determine the location of the appliance. Choose  
a location which provides adequate clearance from  
obstacles such as electrical wiring, conduit, framing  
members, plumbing pipe, etc.  
20012734  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
6. Install the ceiling support cathedral ceiling support  
box assembly, as appropriate.  
NOTE: Whenever DIRECT-TEMP penetrates through a  
ceiling, a floor or a wall, it must be firestopped.  
7. Determine the distance from the appliance outlet to  
a point just above [approximately 12” (305 mm) to 24”  
(610 mm)] either the cathedral ceiling support box or  
the ceiling support plate and assemble lengths of pipe  
to satisfy this distance. Do not attach assembly to appli-  
ance.  
12. Using a level, make sure the system is perfectly  
vertical.  
13. Slide the flashing, suitable for the roof pitch, down  
over the pipe protruding through the roof. Recheck  
orientation and use a silicone sealant around and under  
the perimeter of the flashing where it is in contact with  
the roof. Secure the flashing with roofing nails. Finish  
roofing around the pipe, covering the sides and upper  
ares of the flashing base with roofing material. How-  
ever, be sure the lower unnailed portion of the base  
covers the roofing material.  
8. Loosely position the support collar around the as-  
sembled lengths (flared end down).  
9. From above, lower the assembled pipe sections  
down through the cathedral ceiling box or ceiling sup-  
port plate and attach it to the appliance adapter. The  
support collar should then be adjusted so that when  
the assembled lengths of pipe are attached to the ap-  
pliance, it rests on the bottom of the cathedral ceiling  
support box on top of the ceiling support plate.  
14. Position the storm collar around the pipe and slide  
down until it is in contact with the flashing. Secure the  
storm collar by inserting the two (2) tabs into the raised  
slots and fold tabs back. Seal the area between the  
storm collar and the vent pipe with a silicone sealant to  
prevent rain infiltration.  
10. Tighten the tabs of the collar. Secure the sup-  
port collar by inserting three (3) #8 x 1/4” sheet metal  
screws through the support collar and the outer wall of  
the pipe.  
15. Install the vertical termination (VC) by inserting it  
down into the top most section of pipe until it is fully  
seated. Depress lock tab to secure the cap to the pipe.  
NOTE: In high wind areas, it is recommended to screw  
termination to the pipe with two (2) #8 x 1/4” sheet  
metal screws. The screws should be approximately 3/4”  
from the bottom of the vertical termination’s galvanized  
collar.  
NOTE: If the cathedral ceiling support box assembly is  
being used, it may be necessary to temporarily connect  
the assembled pipe to the appliance. Determine and  
mark the location of where the support collar will be at-  
tached to the pipe. Disconnect and remove assembled  
pipe. Attach the support collar per Step 10 (where  
marked) and reinstall assembly. This is due to limited  
space within the cathedral ceiling support box. Install  
any required offset supports.  
Venting System Assembly - Natural Vent  
General Information  
The Stardance Heater is shipped from the factory as a  
Direct Vent Heater. It may be converted to a Natural  
Vent heater by installing the Vermont Castings Model  
Z31B00 FSDHAG Draft Hood Adapter.  
11. Add lengths of pipe and firestop as necessary  
until assembly extends to a point above the roof which  
complies with local code requirements for minimum ter-  
mination height and with the appliance manufacturer’s  
installation instructions. (Fig. 44)  
The Stardance Heater is approved for installation as  
a Natural Vent. CFM Direct Vent pipe could be used  
directly after the Draft Hood Adapter up to the ceiling,  
then B-vent pipe must be used. Do not mix types of B-  
vent pipe; use components from one maker or the other.  
Follow the vent component maker’s instructions exactly.  
The heater will also accept standard or enamelled 7”  
(178mm) diameter pipe, around the Type B venting, for  
decorative purposes only. (Fig. 45)  
Minimum  
Roof Pitch  
Flat to 7/12  
Height  
1’0”  
1’6”  
2’0”  
2’6”  
3’3”  
4’0”  
5’0”  
6’0”  
7’0”  
7’6”  
8’0”  
Over 7/12 to 8/12  
Over 8/12 to 8/12  
Over 9/12 to 10/12  
Over 10/12 to 11/12  
Over 11/12 to 12/12  
Over 12/12 to 14/12  
Over 14/12 to 16/12  
Over 16/12 to 18/12  
Over 18/12 to 20/12  
Over 20/12 to 21/12  
Minimum Height  
Above Roof  
NOTE: The restrictor plate supplied with the stove  
is not used for Natural Vent applications.  
The Stardance stove, when installed as a Natural vent  
heater, includes a vent safety switch. (Page 41, Figure  
81) Operating the stove when it is not connected to a  
properly installed and maintained venting system, or  
tampering with or disconnecting the vent safety switch,  
can result in carbon monoxide (CO) poisoning and pos-  
sible death.  
Fig. 44 Minimum Height Above Roof Requirements  
20012734  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
For U.S. installations: The venting system must con-  
form with local codes and/or the current National Fuel  
Gas Code, ANSI Z22.1.  
CFM Direct Vent  
System may be  
used after Draft  
Hood up to the  
ceiling  
Decorative  
7” Pipe  
For Canadian installations: The venting system must  
conform to the current CSA B149.1 installation code.  
4” B-vent  
Pipe  
Install the Vent Pipe  
Draft Hood  
Adapter  
Apply a bead of sealant around bottom end of inner  
starter pipe (found in bag with logset) and attach to  
stove. Apply a bead of sealant around top of inner  
starter pipe and install the Z31B00 FSDHAG Draft Hood  
according to Draft Hood instructions. (Fig. 45)  
Attach the first section of venting to the draft hood. De-  
pending on the length of the individual venting sections  
and the lengths of the decorative pipe (if installed), you  
may need to slip the decorative pipe over the venting  
sections before attaching upper sections to lower ones.  
The sections of decorative pipe should be oriented with  
their seams (if any) toward the wall; sections usually  
do not need to be fastened at each joint, other than  
slip sections. If the layout includes a slip section, this  
should be the last section of pipe visible in the room, at  
the ceiling. Complete the venting according to the vent  
maker’s instructions.  
ST358  
Fig. 45 Decorative 7” pipe may be fitted around the B-vent  
pipe.  
Install the Log Set  
CAUTION: Before installation, inspect ember bed  
burner for damage. Do not use ember bed if damaged  
or cracked. NOTE: Small, shallow surface cracks are  
acceptable.  
1. Remove the logs from their packaging and inspect  
each piece for damage. DO NOT INSTALL DAM-  
AGED LOGS.  
Rear Log  
Figure 46  
2. Install the rear log by mating  
the notch on the bottom of  
the log with the raised notch  
on the back left side of the  
ember bed. (Fig. 47) Ensure  
the cutout in the right side of  
the log is sitting around the  
pilot assembly and pilot is  
not obstructed. (Fig. 46)  
LG493  
20012734  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Pilot Assembly  
Figure 47  
Raised Notch  
Raised Notch  
Pin  
LG497  
Figure 48  
3. Install the left log by  
mating the hole on the  
bottom of the log with  
the pin in the ember  
bed. (Fig. 48) Position  
the log over air hole in  
ember bed.  
Left Log  
Right Log  
4. Install the right log by  
mating the notch on the  
bottom of the log with  
the raised notch on the  
ember bed. (Fig. 48)  
Position the log over air  
hole in ember bed.  
Rear Log  
LG494  
Top Log  
Figure 49  
5. Install top log by  
mating hole on bot-  
tom of log with locat-  
ing pin on top right  
Left Log  
side of rear log. (Fig.  
Right Log  
49) Position log so  
it is angled down to-  
ward the area where  
the front two logs  
meet.  
LG495  
Ember Bed  
20012734  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Page 46 for correct conversion kit.  
Connect the Gas Supply Line  
Conversion instructions are provided with each kit and  
beginning on Page 37 in this manual.  
Check the Rating Plate attached by a steel cable to the  
firebox, to confirm that you have the appropriate firebox  
for the type of fuel to be used. The Stardance may be  
converted from one gas to another using the appropri-  
ate Fuel Conversion Kit listed on Page 46.  
THIS APPLIANCE SHOULD BE CONNECTED TO  
THE GAS SUPPLY ONLY BY A QUALIFIED GAS  
SERVICE TECHNICIAN.  
THERE MUST BE A GAS SHUT-OFF BETWEEN  
THE STOVE AND THE SUPPLY.  
CAUTION  
This appliance should only be connected  
by a qualified gas technician. Test to  
confirm manifold pressures as specified  
below.  
In order to connect Natural Gas, use a fitting with 3/8”  
NPT nipple on the valve side and 1/2” natural gas sup-  
ply line with an input of 28,000 BTUs at a manifold pres-  
sure of 3.5” and minimum inlet supply for adjustment of  
5.5” w.c.  
The Stardance Heater and its individual shutoff  
valve must be disconnected from the gas supply  
piping during any pressure testing of that system  
at test pressures in excess of 1/2 psig (3.5 kPa).  
In order to connect Propane, use a fitting with 3/8”  
NPT nipple on the valve side and 1/2” propane gas  
supply line with an input of 28,000 BTUs at a manifold  
pressure of 10.0” and minimum inlet supply for adjust-  
ment of 11.0” w.c.  
The Stardance Heater must be isolated from the  
gas supply piping system by closing its indi-  
vidual manual shutoff valve during any pressure  
testing of the gas supply piping system at test  
pressure equal to or less than 1/2 psig.  
Install ON/OFF Switch  
The switch assembly parts are found in the parts bag.  
There must be a gas shutoff between the stove  
and the supply.  
1. Attach switch assembly to left rear side of stove  
shroud (when facing shroud) using two screws and  
existing holes in shroud. (Fig. 50)  
In order to connect Natural Gas, use a fitting with  
3/8” NPT nipple on the valve side and 1/2” natural  
gas supply line with an input of 28,000 BTUs at a  
manifold pressure of 3.5” and minimum inlet sup-  
ply for adjustment of 5.5” w.c.  
2. Run wires down back of stove, under bottom of rear  
shroud to valve.  
3. Attach wires to valve terminals. (Fig. 51)  
In order to connect Propane, use a fitting with  
3/8” NPT nipple on the valve side and 1/2” pro-  
pane gas supply line with an input of 28,000 BTUs  
at a manifold pressure of 10.0” and minimum inlet  
supply for adjustment of 11.0” w.c.  
Switch  
Assembly  
Existing Holes  
In the U.S.; Gas connection should be made in ac-  
cordance with current National Fuel Gas Code, ANSI  
Z223.1/NFPA 54. Since some municipalities have  
additional local codes, be sure to consult your local  
authority.  
Screws  
ST315  
Fig. 50 Attach switch assembly to rear shroud.  
In Canada; consult the local authority and CSA-B149.1  
installation code.  
Always check for gas leaks with a mild  
soap and water solution. Do not use an  
open flame for leak testing.  
Light the pilot according to the directions on Page 31,  
before going to the next step.  
Burner Information  
The appliance must only use the gas specified on the  
rating plate, unless converted using a Vermont Castings  
Fuel Conversion Kit. To convert from Natural Gas to LP  
use Kit #20012735 or 20012904. To convert from LP to  
Natural Gas use Kit #20012903 or 20012905. Refer to  
ST228  
Fig. 51 Attach switch wires to valve.  
20012734  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Install the Front Plate  
Thermostat Connection (optional)  
Hold the front plate by the window bars and lift it into  
position, engaging the two steel tabs on the top corners  
behind the adjacent bosses in the side plates. (Fig. 52)  
Then seat the Front against the sides so the tabs at the  
bottom lip engage with the notches in the stove legs.  
Use only a thermostat rated for 500 millivolts.  
Check the table below for the appropriate gauge ther-  
mostat wire to use for the length of lead required in your  
installation.  
Thermostat  
When properly installed, the bottom of the Front Plate  
cannot be pulled away from the sides without also lifting  
it.  
Wire / Gauge  
Maximum Run  
20 feet  
20 - 40 feet  
up to 60 feet  
18  
16  
14  
1. Install the wall thermostat in the desired location and  
run the wires to the stove location. Terminate these  
leads with 1/4” female connectors.  
Engage steel tabs  
gehind the cast  
iron bosses  
2. Connect the thermostat wires to the valve. (Fig. 51)  
Control Door  
Bottom tabs engage  
notch in the leg.  
ST474  
Fig. 52 Install the front plate.  
This completes assembly of the Stardance stove.  
Operation  
�
�������  
��������������  
������������  
������������������  
�������������  
��������������������  
���������������  
ST935  
The Stardance is operated with the front plate in place  
with the doors open or closed. To open the front doors,  
pull forward to separate the magnetic catch.  
Fig. 53 Pilot assembly location.  
Pilot and Burner Inspection  
CAUTION: DO NOT TOUCH DOORS WHEN  
HOT!  
Each time you light your heater check that the pilot  
flame and burner flame patterns are as shown in Figure  
55. If flame patterns are incorrect, turn the heater off.  
Contact your dealer or a qualified gas technician for as-  
sistance. Do not operate the heater until the pilot flame  
is correct.  
Your First Fire  
Read these instructions carefully and familiarize your-  
self with the burner controls. Locate the pilot assembly,  
Figure 53. Follow the lighting instructions on Page 31  
exactly.  
Follow regular maintenance procedures as described  
on Page 41.  
During the first fire, it is not unusual to smell some odor  
associated with new logs, paint and metal being heated.  
Odors should dissipate within an hour or so, however,  
you can open a window to provide fresh air to alleviate  
the condition.  
20012734  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Flame & Temperature Adjustment  
Flame Characteristics  
For stoves equipped with HI/LO valves, flame adjust-  
ment is accomplished by rotating the HI/LO adjustment  
knob located near the center of the gas control valve.  
(Fig. 54)  
It is important to periodically perform a visual check  
of the pilot and the burner flames. Compare them to  
Figure 55. If any of the flames appear abnormal, call a  
service person.  
Turn  
counterclockwise  
Turn clockwise  
to decrease  
to increase  
flame height  
flame height  
Fig. 54 Flame adjustment knob for SIT valve.  
SDDVT Series  
CO105d  
SDDVTC Series  
(Comfort Control Models)  
LG496  
Fig. 55 Correct pilot and burner flame patterns.  
20012734  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Lighting and Operating Instructions  
FOR YOUR SAFETY READ BEFORE LIGHTING  
WARNING:If you do not follow these instructions exactly, a fire or explosion  
may result causing property damage, personal injury or loss of life.  
A. This heater has a pilot which must be lit manu-  
ally. When lighting the pilot follow these instruc-  
tions exactly.  
Follow the gas supplier’s instructions.  
• If you cannot reach your gas supplier, call  
the Fire Department  
B. BEFORE LIGHTING smell all around the  
heater area for gas. Be sure to smell next to  
the floor because some gas is heavier than air  
and will settle on the floor.  
C. Use only your hand to push in or turn the gas  
control knob. Never use tools. If the knob will not  
push in or turn by hand, do not try to repair it, call a  
qualified service technician. Applying force or any  
attempted repair may result in a fire or explosion.  
D. Do not use this fireplace if any part has been under  
water. Immediately call a qualified service techni-  
cian to inspect the heater and to replace any part of  
the control system and any gas control which has  
been under water.  
WHAT TO DO IF YOU SMELL GAS  
• Do not try to light any fireplace  
• Do not touch any electric switch  
• Do not use any phone in your building  
• Immediately call your gas supplier from a  
neighbor’s phone.  
Lighting Instructions  
1. STOP! Read the safety information above.  
2. Turn off all electrical power to the fireplace.  
3. Turn the ON/OFF switch to “OFF” position, set  
the remote to OFF or set thermostat to lowest  
level.  
10. Push the control knob all the way in and hold.  
Immediately light the pilot by repeatedly depress-  
ing the piezo spark ignitor until a flame appears.  
Continue to hold the control knob in for about one  
(1) minute after the pilot is lit. Release knob and it  
will pop back up. Pilot should remain lit. If it goes  
out, repeat steps 5 through 8.  
4. Open control access panel.  
5. Push in gas control knob slightly and turn clock-  
wise  
to “OFF”.  
3/8" - 1/2"  
OFF  
Honeywell  
Euro SIT  
SIT NOVA  
•
If knob does not pop up when released, stop  
and immediately call your service technician or  
gas supplier.  
6. Remove glass door before lighting pilot. (See  
Glass Frame Removal section).  
•
If after several tries, the pilot will not stay lit,  
7. Wait five (5) minutes to clear out any gas. Then  
smell for gas, including near the floor. If you  
smell gas, STOP! Follow “B” in the safety infor-  
mation above. If you do not smell gas, go to the  
next step.  
8. Visibly locate pilot by the main burner.  
9. Turn knob on gas control counterclockwise  
to “PILOT”.  
turn the gas control knob to “OFF” and call your  
service technician or gas supplier.  
11. Replace glass door.  
12. Turn gas control knob to “ON” position.  
13. Turn the ON/OFF switch to “ON” position or set  
thermostat to desired setting.  
14. Turn on all electrical power to the fireplace.  
To Turn Off Gas To Heater  
1. Turn the ON/OFF switch to Off position or set  
the thermostat to lowest setting.  
3. Open control access panel.  
4. Push in gas control knob slightly and turn clock-  
2. Turn off all electric power to the fireplace if  
service is to be performed.  
wise  
to “OFF”. Do not force.  
5. Close control access panel.  
20012734  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Troubleshooting the Gas Control System (SDDVT Series)  
SIT NOVA 820 MILLIVOLT VALVE  
NOTE: Before trouble shooting the gas control system, be sure external gas shut off is in the “On” position.  
Possible Causes  
Corrective Action  
Symptom  
1. Spark ignitor will not light  
A. Defective or misaligned electrode  
at pilot  
Using a match, light pilot. If pilot lights, turn off pilot and  
push the red button again. If pilot will not light - check  
gap at electrode and pilot-should be 1/8” to have a  
strong spark.  
With the control knob in the pilot position, push the  
control knob all the way and hold. Check for spark at  
electrode and pilot. If no spark to pilot, and electrode  
wire is properly connected, replace the battery in the  
ignitor module and try again. Refer to Maintenance  
Section. If the problem still exists, replace the ignitor  
module box.  
B. Defective ignitor (Push Button)  
Check pilot flame. Must impinge on thermocouple/ther-  
mopile. NOTE: This pilot burner assembly utilizes both  
a thermocouple and a thermopile. The thermocouple  
operates the main valve operation (On and Off). Clean  
and or adjust pilot for maximum flame impingement on  
thermopile and thermocouple.  
2. Pilot will not stay lit after  
carefully following lighting  
instructions  
A. Defective pilot generator (thermo-  
couple), remote wall switch  
B. Defective automatic valve  
Turn valve knob to “Pilot”. Maintain flow to pilot; millivolt  
meter should read greater than 10mV. If the reading  
is okay and the pilot does not stay on, replace the gas  
valve. NOTE: An interrupter block (not supplied) must  
be used to conduct this test.  
Check wall switch and wires for proper connections.  
Jumper wire across terminals at wall switch, if burner  
comes on, replace defective wall switch.. If okay,  
jumper wires across wall switch wires at valve, if burner  
comes on, wires are faulty or connections are bad.  
3. Pilot burning, no gas to  
main burner  
A. Wall switch or wires defective  
1. Be sure wire connections form thermopile at gas  
valve terminals are tight and thermopile is fully  
inserted into pilot bracket.  
B. Thermopile may not be generat-  
ing sufficient millivoltage  
2. One of the wall switch wires may be grounded. Re-  
move wall switch wires form valve terminals if pilot  
now stays lit, trace wall switch wiring for ground.  
May be grounded to fireplace or gas supply.  
3. Check thermopile with millivolt meter. Take reading  
at thermopile terminals of gas valve. Should read  
250-300 millivolts (minimum 150) while holding  
valve knob depressed in pilot position and wall  
switch “Off”. Replace faulty thermopile if reading is  
below specified minimum.  
C. Plugged burner orifice  
Check burner orifices for debris and remove.  
Turn valve knob to “On”, place wall switch to “On”  
millivolt meter should read greater than 150mV. If the  
reading is okay and the burner does not come on,  
replace the gas valve.  
D. Defective automatic valve opera-  
tor  
Clean and/or adjust pilot flame for maximum flame  
impingement on thermopile and thermocouple.  
4. Frequent pilot outage  
problem  
A. Pilot flame may be too low or  
blowing (high) causing the pilot  
safety to drop out  
B. Possible blockage of the vent  
terminal  
Check the vent terminal for blockage (recycling the flue  
gases).  
20012734  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
7. If the manual switch is in the LOCAL position, the  
valve will be at the highest fixed pressure setting and  
the fan will be at the highest fixed speed. The trans-  
mitter will control the fan only.  
Instructions for RF Comfort Control Valve  
SDDVTC Series  
The Comfort Control valve allows remote control of tem-  
perature, fan and flame appearance.  
Shut Off Procedure  
NOTE: The antenna should hang in free air away form  
grounded metal.  
If the manual switch is in the REMOTE position, the  
transmitter can shut off the main burner and fan. How-  
ever, the control is still on and a command from the  
transmitter can turn on the main burner or fan.  
Operation  
1. If the manual switch is in remote position, switch it to  
LOCAL. (Fig. 56)  
To shut off the system, turn the pilotstat knob clockwise  
to the OFF position. This action closes the main gas  
and safety valves. The transmitter cannot turn on the  
main burner or fan.  
2. Turn the pilotstat knob counterclockwise from OFF to  
the PILOT position, push the knob down, and hold in  
position. The pilot valve opens and allows gas to flow  
to the pilot burner.  
Transmitter Operation  
Off Mode  
3. Push plunger on the piezo until the pilot burner is lit.  
When the pilot burner is lit, the LED on the control  
will come on after approximately 40 seconds and  
will provide 1 short blink continuously in the normal  
mode. When the light turns off which will be approxi-  
mately 10 seconds after it has been continuously  
red, the receiver/valve is fully powered.  
Display  
Room Temperature  
Set Temperature  
Flame Height Level  
Fan Speed Level  
Mode  
Countdown Timer  
Auto  
Low Battery  
On  
Off  
Flame  
Motor Top Cap  
Piezo Ignitor  
Up  
Countdown  
Timer  
Increase Flame Height,  
Fan Speed Timer, or  
Set Point  
OFF  
•
Down  
Decrease Flame, Fan  
Speed Timer or Set  
Point  
Fan  
FP1039  
Fig. 57 Transmitter diagram.  
In the OFF mode, the fireplace flame and fan are  
off, the display will show OFF and displays the room  
temperature. If the receiver is in REMOTE mode, the  
fireplace will shut off.  
LED  
Local/Remote  
Switch  
Pilotstat  
Knob  
Plug  
Antenna  
FP1037  
Fig. 56 Comfort control valve.  
On (Manual) Mode  
4. Release the knob. The shaft will move upward. The  
pilot burner should now stay burning. If the pilot  
burner goes out, repeat step 2.  
In the ON mode, the room temperature, flame and fan  
levels will be shown. MANUAL will appear next to both  
the flame and fan icons.  
5. Turn the knob counterclockwise to the ON position. If  
the manual switch is in the LOCAL position, the main  
burner will turn on immediately.  
When the control is in the ON mode, the flame and fan  
levels, and delay timer are changed with the up and  
down buttons. To change the flame level, press the  
flame button followed by an arrow key. To change the  
fan level, press the fan key followed by an arrow key.  
Pushing the arrow key once will change the level by  
one unit.  
6. ON the initial use of a transmitter, a recognition  
operation is required between the receiver/valve and  
transmitter. Change the switch from LOCAL to RE-  
MOTE. Press the fan or flame button on the transmit-  
ter within 30 seconds. The LED will blink indicating  
the transmitter will now work with the receiver/valve.  
If the switch continues in the REMOTE position, the  
transmitter will now control the main valve, flame  
modulation level and fan control.  
Delay Timer Mode  
The shut off delay timer has a maximum of 2 hours and  
a minimum of zero minutes. To change the timer level,  
press the time key followed by an arrow key. Pushing  
the key once will change the timer by 10 minutes.  
20012734  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Auto Mode  
Pilot  
In the AUTO mode, the room temperature, set tem-  
perature, flame and fan levels will be shown. AUTO will  
appear next to both the flame and fan icons.  
Assembly  
Fan  
When the control is in the AUTO mode, the main burner  
will turn on/off or modulate based on the heat needed  
to maintain the set temperature. The flame level will  
change automatically to optimize the heat output  
needed to maintain the set temperature. To change the  
set temperature, press the up or down key. Pushing a  
key once will change the temperature by one degree.  
N A F  
Red  
White  
In the AUTO mode, the fan speed will increase with  
increasing flame height or decrease with decreasing  
flame height. “AUTO” is displayed next to the flame and  
fan icons.  
Red  
White  
White Dots  
Antenna  
Fan Override During Auto Mode  
Comfort Control Valve  
FP1038  
(Bottom View)  
If a lower or higher fan speed is desired when operating  
in the AUTO mode, the fan speed can be overridden by  
pushing the fan button followed by the up or down key.  
Pushing a key once will change the fan level by one  
unit. In this mode “AUTO” is displayed next to the flame  
icon and “MANUAL” is displayed next to the fan icon.  
Fig. 58 Comfort valve wiring diagram.  
5. In the event of multiple failure codes, next failure  
code follows previous failure code by approximately  
3 seconds.  
If an Error Code 3 is observed while performing the  
testing, complete the following:  
1. Make sure the spade connectors are pushed all the  
way on. If rhe Error Code 3 is still showing, then go  
to the next step.  
2. Switch the front two thermopile leads with the back  
two. Be sure the white lead is connected to the  
spade with the white dot next to it. If the Error Code  
3 is still showing, replace the thermopiles.  
If an Error Code 8 is observed while performing the  
testing, complete the following:  
Change Between F/C Temperature Units  
Push the up and down arrow keys simultaneously for  
at least 3 seconds to toggle between Fahrenheit and  
Celsius units.  
Disable Thermostat Function  
To disable the thermostat function in the AUTO mode,  
push the time and down keys simultaneously for at least  
3 seconds.  
1. Confirm the valve is not in REMOTE mode.  
• If the valve is producing Error Code 8 and in RE-  
MOTE mode, the valve is defective and should be  
replaced.  
• If the valve is in LOCAL mode and producing Error  
Code 8, then go to the next step.  
2. Slide the Remote/Local switch to REMOTE and  
teach the valve a transmitter (see item 6, page 32).  
The Error Code will clear itself after approximately  
1.5 minutes and return to normal operation.  
To Change Batteries  
1. Remove cover on the backside of the transmitter.  
Install 3 AAA batteries as shown and reattach cover.  
2. Once steps 1-3 in OPERATION are completed,  
receiver/valve and transmitter are now ready. Press  
any button on transmitter for recognition process to  
occur between the receiver/valve and transmitter.  
3. Use functions as described in TRANSMITTER sec-  
tion.  
LED Count  
Service Action  
Replace valve  
Confirm stepper motor connection exists  
Confirm fan connection exists and works  
Confirm gas type; jumper in place  
Replace thermopiles  
Troubleshooting  
8
7
5
4
3
2
1. Locate LED light on valve.  
2. LED will blink after every valid command received by  
the transmitter; this is not an error.  
3. Failure codes may occur anytime after pilot burner is  
lit.  
Turn fan ON  
4. Sequence is failure code followed by light not blink-  
ing for 30 seconds.  
NOTE: Some keys are not active.  
20012734  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Comfort Valve System Control Sequence of Operation with Transmitter  
Set manual switch  
to local or remote  
five minute wait  
period  
Light pilot burner  
Did the LED stop  
blinking?  
Review LED  
failure analysis  
Release pilotstat  
knob  
Yes  
Cycle switch once  
and leave in remote.  
Pressy any key on  
transmitter for  
Choose Manual or  
Remote path. Set  
switch to manual or  
remote.  
Turn pilotstat knob  
from PILOT to ON  
recognition operation  
On Path  
Local Path  
Move switch from  
If manual switch is  
If the manual switch  
local to remote.  
Press any key on  
transmitter. Move  
switch back to  
local.  
Move switch from  
set to LOCAL, did  
main burner light and  
fan turn on?  
is set to REMOTE,  
press the mode but-  
ton to display “ON”.  
Does transmitter con-  
trol the main burner  
and fan?  
manual to remote.  
Press any key on  
transmitter.  
Yes  
Turn pilotstat knob  
to PILOT to turn off  
main burner.  
Yes  
Does transmitter  
No  
change levels of flame  
height, fan speed?  
Turn pilotstat knob  
to OFF to turn valve  
completely off.  
Set levels of flame  
height and fan to “0:  
to shut off main burner  
and fan.  
Turn pilotstat knob  
to OFF to turn valve  
completely off.  
20012734  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Auto Path  
If the manual switch is set  
to REMOTE, press the  
mode button to display  
AUTO on the transmitter.  
Does the transmitter dis-  
play the room and tempera-  
ture setting?  
Move switch from  
LOCAL to REMOTE.  
Press any key within  
30 seconds.  
If the setting is above  
room temperature on the  
transmitter, does the main  
valve and fan turn on?  
No  
No  
If the settings is below  
room temperature on the  
transmitter, does the main  
valve and fan turn off?  
Turn pilotstat knob to OFF  
to turn valve completely  
off.  
20012734  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Fuel Conversion Instructions  
nal key-way of  
the screw (Fig.  
61), rotate it  
counterclock-  
wise until it  
WARNING! This conversion kit shall be installed  
by a qualified service agency in accordance with  
the manufacturer’s instructions and all applicable  
codes and requirements of the authority having  
jurisdiction. If the information in these instruc-  
tions is not followed exactly, a fire, explosion  
or production of carbon monoxide may result  
causing property damage, personal injury or loss  
of life. The qualified service agency is respon-  
sible for the proper installation of this kit. The  
installation is not proper and complete until the  
operation of the converted appliance is checked  
as specified in the manufacturer’s instructions  
supplied with the kit.  
Figure 60  
Figure  
61  
is free and  
extract it.  
�
�
5. Check that the  
screw is clean  
and if neces-  
sary remove  
dirt.  
�
�
6. Flip the screw.  
(Fig. 62)  
Figure 62  
CAUTION: The gas supply shall be shut off prior  
to disconnecting the electrical power, before pro-  
ceeding with the conversion.  
7. Using the Al-  
len wrench as  
shown in Figure  
63, rotate the  
screw clockwise  
and tighten until  
snug.  
Figure 63  
�
�
WARNING: Do  
not overtighten  
the screw. Rec-  
ommended to  
grip the wrench  
by the short  
side.  
Main Gas  
Line  
�
�
Gas Supply Inlet  
ST226a  
Fig. 59 Attach the gas line to the left side of the valve.  
8. Verify that if the  
Conversion Precautions  
conversion is from NG to LP, the  
screw must be reassembled with the red o-ring vis-  
ible. (Fig. 64)  
Before proceeding, turn control knob on valve to OFF  
and turn gas supply OFF. Turn OFF any electricity that  
may be going to the appliance.  
9. Replace the black protection cap.  
Conversion Procedure  
WARNING: Check that also the pilot and  
main burner injectors are appropriate for  
the gas type.  
1. Remove stove front. Lift stove front up and then  
swing bottom out and away to disengage from the  
stove body. (Page 41, Fig. 75)  
Figure 64  
Natural Gas  
Configuration  
2. Swing open the swiveling latches at the top left and  
right corners of the glass frame. (Page 42, Fig. 76)  
LP Configuration  
�
�
�
�
3. Pull the top edge of the glass and frame assembly  
away from the firebox face. Place the assembly out  
of the way on a flat, padded surface such as a coun-  
ter protected by a towel.  
Red O-ring Visible  
Red O-ring NOT Visible  
CO141  
4. Remove the logset from the firebox.  
Valve Conversion  
SDDVTC Series Models  
SDDVT Series Models  
1. Follow procedure for pilot type 2 to replace pilot  
orifice.  
1. Turn control knob to the OFF position, and shut off  
the gas supply to the valve.  
2. Remove and replace plug on lower right hand side  
of the valve; Red for LP and Blue for NG. (Page 32,  
Fig. 56)  
2. Allow the valve to cool to room temperature.  
3. Remove the black protection cap by hand. (Fig. 60)  
4. Insert a 5/32” or 4 mm Allen wrench into the hexago-  
20012734  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
3. Remove motor top cap using a standard slotted  
screwdriver. Depress and turn center plunger until  
arrow points to correct screw. Red for LP and Blue  
for NG. NOTE: Plunger will “snap” into NG position  
when arrow is close to blue screw. It will not “snap”  
at LP (Red) position. (Fig. 65)  
Index Tab  
Allen Wrench  
Snap Ring  
Motor Top Cap  
Center  
CO106a  
Plunger  
Fig. 68 Remove pilot orifice.  
• Reinstall pilot hood. Be sure to align hood with  
index tab.  
Valve  
Pilot type 2  
Blue - NG  
Red - LP  
• Loosen pilot hood turning counterclockwise using a  
7/16” wrench. (Fig. 69) NOTE: You may use pen-  
etrating oil to prevent pilot hood threads from seizing  
up.  
FP1037b  
Fig. 65 Depress and turn center plunger.  
4. Insure manifold pressure remains between 3.2” - 3.5”  
w.c. for NG and 9.5” - 10” w.c. for LP. To adjust the  
manifold pressure, for NG, using a Torx #10 key turn  
the blue screw clockwise to increase the manifold  
pressure. Turn the screw counterclockwise to de-  
crease the pressure. Use the red screw to adjust LP.  
• Remove pilot orifice with needlenose pliers. (Fig.  
70) NOTE: Use a wrench to hold pilot tube in place  
while removing the orifice.  
• Install the conversion orifice.  
• Reinstall pilot hood and tighten until mark on pilot  
hood aligns with mark on pilot bracket.  
5. Replace motor top cap.  
Pilot Orifice Conversion  
1. Locate pilot. (Fig. 66)  
Pilot  
Index  
Marks  
Pilot Bracket  
CO143  
Fig. 69 Remove pilot hood. (Your pilot may have a different  
appearance.)  
ST935  
Fig. 66 Pilot assembly location.  
2. Replace pilot orifice.  
Pilot Orfice  
Pilot Type 1  
• Remove pilot hood by lifting up. (Fig. 67) Do not  
remove snap ring to remove pilot hood. NOTE: It is  
not necessary to remove the pilot tube for conver-  
sion.  
• Remove pilot orifice with Allen wrench. (Fig. 68)  
• Install the conversion orifice.  
CO144  
Fig. 70 Remove pilot orifice.  
Pilot Hood  
Pilot  
Bracket  
CO105a  
Fig. 67 Remove pilot hood.  
20012734  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Burner Orifice Conversion  
1. Remove three (3) 3/8” nuts on bottom side of burner  
pan. (Fig. 71)  
2. Carefully remove ember bed by tilting the right side  
up and lifting out toward the right side of the unit.  
(Fig. 72)  
Remove Nut  
CO145  
Fig. 73 Use two wrenches to avoid damage to manifold.  
Orifice  
Orifice  
Bracket  
Air Shutter  
Bottom View  
Remove Nuts  
ST918  
Fig. 71 Remove three (3) nuts securing ember bed in place.  
Orifice  
Venturi Bracket  
Bracket  
CO142  
Fig. 74 The air shutter setting is 1/2” (13 mm) from the orifice  
bracket to the edge of the air shutter.  
All Models  
1. Replace burner making sure venturi on bottom of  
ember bed aligns with orifice and is seated properly  
on air shutter assembly. (Fig. 72) Make sure burner  
is slid into place at a slight angle and opposite to  
how it was removed. When burner is slid into place,  
the three (3) pem studs should slide down through  
clearance holes into the bottom of the control panel.  
Pem Studs  
ST919  
Fig. 72 Tilt ember bed slightly to correctly place on venturi  
and air shutter.  
3. Remove injector orifice from left burner bracket with  
a 1/2” wrench. Use a back up wrench to prevent  
damage to the manifold. (Fig. 73)  
2. Thread and tighten 3/8” nuts back onto pem studs  
on underneath side of control panel, reversing Step  
1 shown in Figure 71.  
4. Install conversion orifice. (Refer to Table 2)  
3. Reinstall logs as per instructions on Page 25.  
4. Place conversion label on valve.  
5. The air shutter is factory set according to table on  
Page 7 and should not need adjustment. The air  
shutter opening may be verified by measuring as  
shown in Figure 74.  
5. Replace glass and stove front.  
6. Restore gas to system and relight appliance accord-  
ing to Lighting Instructions on Page 30.  
7. Leak check the system using a gas leak detector  
solution.  
8. Relight the main burner in both the “HI” and “LO” po-  
sitions to verify proper burner ignition and operation.  
Conversion is complete.  
20012734  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Table 2. Injector Orifice Size Matrix  
Conversion to LP  
Input (BTU/h)  
Model  
Kit #  
Orifice  
Part #  
Minimum Maximum  
SDDVT  
20012735  
20,000  
#53 / .0595” 20007347  
28,000  
SDDVTC  
20012904  
22,000  
Conversion to Natural Gas  
Orifice Part #  
#38 / .101” 20009310  
Input (BTU/h)  
Minimum Maximum  
Model  
SDDVT  
Kit #  
20012903  
20,000  
28,000  
SDDVTC  
20012905  
22,000  
20012734  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Maintenance  
Your Stardance Gas Heater will provide years of service  
with minimal upkeep. The following procedures will help  
ensure that your stove continues to function properly.  
Cleaning the Glass  
WARNING: Allow the glass to cool com-  
pletely before attempting to clean.  
Annual System Inspection  
Have the entire heater and venting system inspected  
annually by a qualified gas technician. Replace any  
worn or broken parts.  
�
�������  
��������������  
������������  
Logset and Burner /  
������������������  
Cleaning and Inspection  
�������������  
Cleanliness is critical to the proper function of the  
heater. The logset and burner must all be kept free of  
dust and unobstructed by debris. Inspect these areas  
before each use and clean as necessary.  
��������������������  
���������������  
It will be necessary to clean the glass periodically. Dur-  
ing start-up, condensation, which is normal, forms on  
the inside of the glass and causes lint, dust and other  
airborne particles to cling to the glass surface. Also  
initial paint curing may deposit a slight film on the glass.  
It is therefore recommended that the glass be cleaned  
two or three times with a non-ammonia household  
cleaner and warm water (we recommend gas fireplace  
glass cleaner). After that the glass should be cleaned  
two or three times during each heating season depend-  
ing on the circumstances present.  
1. Turn the burner OFF and let the heater cool com-  
pletely before cleaning.  
2. Lift the Stove Front up and then swing the bottom  
out to disengage it from the heater shell. (Fig. 75)  
3. Carefully remove the glass and frame assembly and  
place it out of the way on a flat, padded surface such  
as a counter protected by a towel.  
4. Carefully inspect the Logs for damage. Contact your  
local dealer if any damage is evident. DO NOT OP-  
ERATE THE HEATER WITH DAMAGED LOGS.  
Clean glass after first two weeks of opera-  
tion.  
5. Use a soft bristled brush to sweep dust or debris  
from the Logs, Pilot and Burner. Use care as the logs  
are fragile and susceptible to damage. DO NOT USE  
A VACUUM TO CLEAN THE LOGS OR BURNER.  
Glass Replacement  
6. Replace the glass panel and frame assembly.  
7. Replace the Stove Front.  
Replace glass only with CFM Corporation approved  
parts. Refer to Page 44 for Replacement Parts. Refer  
to Figures 75 & 76 for removal of the damaged glass  
frame.  
Care of Cast Iron  
An occasional dusting with a dry rag will help keep the  
painted surfaces looking new. Use high-temperature  
stove paints, available through your local dealer, to  
touch-up areas as needed. Clean areas to be painted  
with a wire brush and be sure to cover the logs, burner  
and valve assembly, glass and frame assembly. Apply  
the paint sparingly; two light coats of paint will give bet-  
ter results than a single heavy coat.  
Clean porcelain enamel surfaces with a soft, damp  
cloth. Do not use abrasive cleaning agents. If neces-  
sary, use only a cleaning agent formulated especially  
for use on porcelain enamel surfaces.  
CAUTION  
ST474a  
TURN THE PILOT OFF BEFORE PAINTING. AL-  
LOW THE HEATER TO COOL COMPLETELY BE-  
FORE PAINTING.  
Fig. 75 Remove the stove front.  
20012734  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Inspect the Vent System Annually  
Have the vent system inspected annually by a qualified  
technician. Shut off the main gas supply before inspect-  
ing the system. Both the inner exhaust pipe and the out-  
er combustion supply pipe must be checked to confirm  
that they are unblocked and in good condition.  
ST208  
Fig. 76 Release the latches to release the glass frame.  
Check the Gas Flame Regularly  
To ensure that the stove is operating properly, check the  
flames periodically to confirm that they match Figure 78.  
The flames will be blue during the first 15-20 minutes of  
operation, and will gradually turn to yellow after that.  
Gasket Replacement  
The Stardance Gas Heater uses a ‘tadpole’ type gasket  
to seal between the glass panel and the frame. In time,  
this gasket can become brittle and compressed and  
should be replaced. New gasket is available from your  
dealer.  
Do not use your stove if the flame pattern differs from  
that shown here. Contact your Vermont Castings dealer  
or a qualified technician for help.  
Shut off the gas supply and allow the stove to cool.  
Wear safety goggles and a dust mask.  
1. Remove the Front, Glass Frame and Glass Panel.  
(Figs. 76 & 77) Remove the old gasket. Use a  
razor blade to separate the glass and gasket from  
the frame, and to clean the glass of any remaining  
cement or bits of gasket. Use a cold chisel if neces-  
sary.  
Figure 78  
2. Determine the correct length of gasket by laying it  
out around the edge of the glass. Allow an extra 1  
- 2” (25-50mm). Mark the spot to be cut. Use a utility  
knife.  
3. Starting on a long edge, remove about 6” of the pro-  
tective paper strip and apply the flat adhesive face  
of the gasket around the outside-facing edge of the  
panel. Continue around the panel, applying a bout 6”  
at a time and being careful to not stretch the mate-  
rial. Do not overlap the gasket ends. (Fig. 77)  
4. Apply a thin bead of high temperature silicone rubber  
sealant along the inside corner of the glass frame, all  
around the perimeter. Place the flat gasketed side of  
the glass panel back into the steel frame. Pinch the  
rounded inside-facing gasket material to bulk it up.  
Stove Disassembly  
If there is ever a need to remove the firebox assem-  
bly from the stove shell, support the firebox with solid  
stands about 6” (152 mm) tall under the left and right  
outer edges of the firebox base. Do not set the firebox  
assembly directly on the floor; this can damage the  
control valve and/or the gas lines from the valve to the  
firebox.  
5. Replace the glass frame and front panel as previ-  
ously described.  
Before removing the firebox from the shell, disconnect  
the on/off switch wires from the valve. If the assembly  
includes the optional fan, disconnect the fan rheostat.  
If the installation includes a wall thermostat, disconnect  
the thermostat leads from valve.  
Disconnection and reconnection to the gas line should  
only be done by a qualified gas service technician.  
Upon reinstallation, the vent system must be sealed to  
the firebox as shown in the installation section, Page  
14. Also be sure the logs are placed in the firebox cor-  
rectly, as shown on Page 25, Figures 46-49.  
ST179  
Fig. 77 Wrap the gasket material around the outside iedge of  
the glass.  
20012734  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Wiring Diagrams  
ON  
OFF  
FAN  
POWER  
CORD  
On/Off Switch  
Wiring  
WHT  
BLK  
TP/TH  
TP  
TH  
Chassis  
Ground  
GRN  
Black  
ST124b  
BLK  
Thermostat  
(Optional)  
Optional Thermostat  
Wiring  
FAN JUNCTION BOX  
TP/TH  
Strain Relief  
TP  
TH  
ON / OFF  
Rheostat  
Black  
ST124c  
Fig. 79 On/Off switch and optional thermostat circuit.  
Snapstat  
NOTE: IF ANY OF THE ORIGINAL WIRE, AS  
SUPPLIED WITH THE APPLIANCE, MUST BE  
REPLACED, IT MUST BE REPLACED WITH TYPE  
SF-2, 200°C WIRE OR ITS EQUIVALENT.  
WHT  
BLK  
GRN  
Drafthood Adapter  
Harness  
Remote Wall Switch or  
ON/OFF Rocker Switch  
RHEOSTAT / SNAPSTAT  
BOX  
Chassis Ground  
ST153  
MOTOR  
Schematic Diagram  
TH  
Gas  
Valve  
TP  
TH  
TP  
ST943  
BLK  
Drafthood  
Sensor  
Gas Pilot w/  
(2) Thermopiles  
SNAPSTAT  
WHT  
BLK  
ON/OFF  
RHEOSTAT  
RF Valve  
Connector  
ST234  
Wiring for RF Valve  
Fig. 81 Stardance fan circuit.  
Do not remove  
this wire  
ST944  
Fig. 80 Draft hood adapter wiring.  
20012734  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
2
6
5
1
1a  
4
1c  
1d  
3
1b  
8
14  
7
11  
12  
15  
9
16  
13  
10  
17  
19  
18  
30a,b  
28a,b  
OFF  
•
27  
LED  
22  
21  
23  
29a,b  
24  
20a  
33  
20c  
34  
20b  
36  
31  
37  
35  
25  
38  
26  
42  
41  
40  
39  
51  
50  
CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time,  
without notice.  
Stardance Direct Vent/Natural Vent Gas Heater  
Models:  
SDDVT Series: SDDVTCB, SDDVTEB, SDDVTMB, SDDVTBS, SDDVTCH, SDDVTVG,  
SDDVTBD,  
SDDVTC Series: SDDVTCCB, SDDVTCEB, SDDVTCMB, SDDVTCBS, SDDVTCCH,  
SDDVTCVG, SDDVTCBD  
20012734  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Stardance Direct Vent/Natural Vent Gas Heater  
SDDVT Series: SDDVTCB, SDDVTEB, SDDVTMB, SDDVTBS, SDDVTCH, SDDVTVG,  
SDDVTBD,  
SDDVTC Series: SDDVTCCB, SDDVTCEB, SDDVTCMB, SDDVTCBS, SDDVTCCH,  
SDDVTCVG, SDDVTCBD  
Ref. Description  
SDDVT/SDDVTC  
20012551  
1. Log Set - Complete  
1a. Log Rear  
20012546  
1b. Log Right  
20012548  
1c. Log Left  
20012547  
1d. Log Top  
20012915  
2. Ember Bed Assembly  
3. Top  
4. Front, Operable Door  
5. Door Right  
6. Door Left  
7. Left End  
20012492  
Refer to Enamel Parts Chart  
Refer to Enamel Parts Chart  
Refer to Enamel Parts Chart  
Refer to Enamel Parts Chart  
Refer to Enamel Parts Chart  
Refer to Enamel Parts Chart  
1301087  
8. Right End  
9. Door, Control  
10. Glass Frame Assembly  
11. Glass  
30000127  
1601691  
12. Gasket, Glass - Med. Knit  
13. Nut, Hex Jam 3/8-16 TOPLK-Z  
14. Pawl Assy, Ash Door  
15. Front Steel Handle/Shaft - NI/VER  
16. Restrictor Plate  
1203702  
1203290  
5004025  
30002717  
20013026  
17. FK26 Fan Subassembly (SDDVTC Series Only)  
18. Valve Nova SIT820.852 RN  
19. Valve Gas Honeywell Convertible RFN RV8310E  
20a. Pilot Assembly 3Way N/DV RN 0.199.706  
Pilot Assembly 3Way N/DV RP 0.199.703  
20b. Pilot, PSE - NA175  
Pilot, PSE - LP175  
30000879  
20012218  
20003719  
10002264  
10002265  
20001115  
20001116  
20c. Pilot Assembly 3Way DV/RFN CS3003A2009  
Pilot Assembly 3Way DV/RFP CS3003A2017  
21. Pilot Top Convertible  
22. Thermocouple 24”  
20002266  
20002268  
10002266  
53373  
7531137  
23. Electrode Ignitor w/Cable SIT24  
24. Thermopile 18” RS  
10001297  
51827  
7533113  
25. Nut Electrode SIT #0.974.144  
26. Tubing Pilot w/Fittings 1/8 x 24”  
27. Thermopile - PSE for RF Pilots  
28a. Pilot Orifice #62 - NG Top Convertible  
28b. Pilot Orifice #35 - LP Top Convertible  
29a. Pilot Orifice PSE RFN  
57886  
10001296  
20002400  
10002268  
10002269  
20000908  
29b. Pilot Orifice PSE RFP  
20000907  
30a. Orifice Hood #53 (.0595”) LP  
30b. Orifice Hood #38 (0.101”) Nat.  
20007347  
20009310  
20012734  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Stardance Direct Vent/Natural Vent Gas Heater  
SDDVT Series: SDDVTCB, SDDVTEB, SDDVTMB, SDDVTBS, SDDVTCH, SDDVTVG,  
SDDVTBD,  
SDDVTC Series: SDDVTCCB, SDDVTCEB, SDDVTCMB, SDDVTCBS, SDDVTCCH,  
SDDVTCVG, SDDVTCBD  
Ref. Description  
SDDVT/SDDVTC  
31. Ignitor Piezo w/Nut SIT  
52464  
32. Bracket Piezo Ignitor (not shown)  
33. Manifold Assembly  
34. Air Shutter Assembly  
20010876  
20012553  
20012517  
30000874  
20002047  
20003561  
10002013  
10002582  
20002282  
1203687  
1206122  
0004345  
20005227  
53821  
30000245  
20003802  
1203560  
30004112  
20012512  
20012514  
35. Trim ON/OFF Switch  
36. Transmitter Honeywell RF  
37. Antennae, Honeywell 395783-1  
38. Sensor 1450 CMG-8184-0032  
39. Wiring Harness  
40. Gasket, Base Pan  
41. Gasket HE Door  
42. Gasket Cement  
43. Handle Package, Ceramic w/Screw (not shown)  
44. Draft Hood Final Assembly (not shown)  
45. Switch Bracket (not shown)  
46. Starter Pipe (not shown)  
47. Rear Shroud (not shown)  
48. 1/4” Fiberglass Gasket (not shown)  
49. *Magnet, Door (not shown)  
50. Right Burner Support Assembly  
51. Tie Bracket Assembly  
*Use common super glue or silicone to attach magnets.  
Fuel Conversion Kits  
Conversion Kit, NG to LP - SDDVT Series  
Conversion Kit, NG to LP - SDDVTC Series  
Conversion Kit, LP to NG - SDDVT Series  
Conversion Kit, LP to NG - SDDVTC Series  
Kit #20012735  
Kit #20012904  
Kit #20012903  
Kit #20012905  
Shell Enamel Part Numbers  
Color  
Classic  
Top  
Left End  
30001280  
30003300  
30001287  
30003308  
30001308  
30001321  
Right End  
30001279  
30003301  
30001286  
30003309  
30001307  
30001320  
Front OP Left Door* Right Door* Left Door** Right Door**  
30001276  
30003305  
30001283  
30001496  
30003302  
30001261  
30003310  
30001270  
30001314  
30001139  
30003304  
30001263  
30003312  
30001272  
30001316  
30001138  
30003303  
30001262  
30003311  
30001271  
30001315  
30004082  
30004090  
30004084  
30004092  
30004086  
30004088  
30004081  
30004089  
30004083  
30004091  
30004085  
30004087  
Biscuit  
Bordeaux  
Chestnut Brown 30003313  
Ebony  
30001304  
30001317  
Midnight Blue  
Vermont  
Classic Green  
30003321  
30003636  
30003316  
30003631  
30003317  
30003632  
30003318  
30003633  
30003320  
30003635  
30003319  
30003634  
30004094  
30004096  
30004093  
30004095  
Brick Blue  
Country  
Cookware Gray 30003644  
30003639  
30003647  
30003655  
30003640  
30003648  
30003656  
30003641  
30003649  
30003657  
30003643  
30003651  
30003659  
30003642  
30003650  
30003658  
30004098  
30004100  
30004102  
30004097  
30004099  
30004101  
Granite Gray  
Sage Green  
30003652  
30003660  
* These doors have a front handle.  
** These doors do not have a handle, they are closed with a magnet.  
20012734  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
Optional Accessories  
Fan Kits  
Screen Kit  
FK26 Fan  
An optional screen, S30SK, for use with the operable  
doors is available to allow the doors to be left in the  
open position.  
The FK26 fan helps distribute heated air from within  
the firebox out into the room. The fan is controlled by a  
snapstat that turns power on and off as the firebox tem-  
perature rises above and falls below a preset tempera-  
ture. A rheostat provides for variable fan speeds.  
Warming Shelf  
Warming shelves add versatility to your stove; they can  
be used to keep foods warm at mealtime.  
Specifications  
Model  
Color  
115 Volt / 60Hz / .75 Amps  
Maintenance  
2702  
2684  
2685  
2688  
2704  
2765  
2711  
30230  
30232  
30233  
30234  
Classic Black  
Biscuit  
Chestnut Brown  
Vt. Classic Green  
Bordeaux  
Ebony  
Midnight Blue  
Brick Blue  
The fan itself does not require regular maintenance,  
however, periodic cleaning of the fan and the surround-  
ing area is required.  
Installation  
Refer to Page 15 for installation instructions.  
Remote Controls  
Country Cookware Gray  
Granite Gray  
Sage Green  
The remote control allows you to turn the heater on or  
off from anywhere in the room. Refer to Page 42 for wir-  
ing diagrams. These remotes for use with RN/RP model  
gas stoves.  
The shelf installation is done in three stages. First you  
attach the shelf loosely to the stove, leaving the screws  
loose enough to allow final adjustments. Then, you po-  
sition the shelf and adjust the brackets so the shelf fits  
correctly. Finally, you tighten the screws.  
Model  
Functions Controlled  
RC1  
RC2  
IMTFK  
ON/OFF  
ON/OFF and Temperature  
Wall mounted thermostat control  
Refer to the instructions included with each warming  
shelf for complete installation procedures.  
Decorative Rings  
7” brass or charcoal gray rings are available to add a  
decorative touch to the exposed stove pipe.  
Model  
Description  
7FSDRG/4  
7FSDRP/4  
7” Charcoal Gray Rings (4)  
7” Polished Brass Rings (4)  
20012734  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
20012734  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
20012734  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Stardance Direct Vent/Natural Vent Gas Heater  
20012734  
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED LIFETIME WARRANTY  
PRODUCT COVERED BY THIS WARRANTY  
All Vermont Castings brand gas stoves, gas inserts, and gas fireplaces installed in the United States of  
America or Canada.  
LIMITED LIFETIME WARRANTY  
•
•
Any part or component replaced under the provisions of this  
warranty is covered for six months or the remainder of the  
original warranty, whichever is longest.  
CFM Corporation (hereinafter referred to as CFM) warrants that  
all cast iron parts, the combustion chamber, ceramic burner,  
and heat exchanger of every Vermont Castings gas product will  
be free of defective material or workmanship during the period  
the product is owned by the original owner subject to proof  
of purchase and the conditions and limitations listed on this  
warranty document.  
Any installation, labor, construction, transportation, or other  
related costs/expenses arising from defective part(s), repair,  
replacement, or otherwise of same, will not be covered by  
this warranty, nor shall the Company assume responsibility  
for same. IN NO EVENT SHALL CFM BE LIABLE FOR ANY  
INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY  
DEFECTS IN THE PRODUCT except as provided by law  
BASIC ONE-YEAR WARRANTY  
CFM warrants to the original owner that your new Vermont  
Castings Gas Appliance is free from defects in material  
or workmanship for a period of one year from the date of  
purchase, subject to the following conditions and limitations.  
Labor to replace these parts is covered for one year, reimbursed  
per our warranty service fee schedule.  
•
•
SOME STATES DO NOT ALLOW FOR THE EXCLUSION  
OR LIMITATIONS OF INCIDENTAL AND CONSEQUENTIAL  
DAMAGES OR LIMITATIONS ON HOW LONG AN IMPLIED  
WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT  
APPLY TO YOUR CIRCUMSTANCES. THIS WARRANTY  
GIVES YOU SPECIFIC RIGHTS AND YOU MAY HAVE OTHER  
RIGHTS WHICH VARY FROM STATE TO STATE.  
COMPONENT WARRANTY LIMITATATIONS  
PORCELAIN ENAMEL FINISHED PARTS: CFM offers no  
warranty on chipping of enamel surfaces. Inspect all products  
prior to accepting them for any damage to the enamel. The  
salt air environment of coastal areas or a high humidity  
environment can be corrosive to the porcelain enamel finish.  
These conditions can cause rusting of the cast iron beneath the  
porcelain enamel finish, which will cause the finish to flake off.  
Color lot variations with parts and/or accessories can occur and  
are not covered by warranty.  
All other warranties expressed or implied with respect to the  
product, its components and accessories, or any obligations/  
liabilities on the part of the Company are hereby expressly  
excluded.  
•
•
The Company neither assumes, nor authorizes any third party  
to assume on its behalf, any other liabilities with respect to the  
sale of this Vermont Castings product  
The warranties as outlined within this document do not apply  
to chimney components or other non CFM Corporation  
accessories used in conjunction with the installation of this  
product.  
GLASS: Glass is not warranted for breakage due to misuse or  
accident. Glass is not covered for discoloration or stains due to  
environmental issues, or improper cleaning and maintenance.  
PLATED PARTS AND ACCESSORIES: Brass, nickel, and gold  
parts should be cleaned with Lemon oil only. Commercial  
cleaners cannot be used. Mortar mix and masonry cleaners  
corrode the brass finish. The CFM will not be responsible  
for, nor will it warrant any brass parts which are damaged by  
external chemicals or down draft conditions.  
•
Damage to the unit while in transit is not covered by this  
warranty but is subject to claim against the common carrier.  
Contact the dealer from whom you purchased your fireplace/  
stove (do not operate the appliance as this might negate the  
ability to process the claim with the carrier).  
•
The Company will not be responsible for:  
ACCESSORIES: Unless otherwise noted, CFM supplied  
accessories are covered for a period of one year.  
a) Down drafts or spillage caused by environmental conditions  
such as near-by trees, buildings, roof tops, hills, or mountains.  
GENERAL CONDITIONS AND LIMITATIONS  
b) Inadequate ventilation or negative air pressure caused by  
mechanical systems such as furnaces, fans, clothes dryers, etc.  
•
This Vermont Castings product must be installed or serviced by  
a qualified installer, preferably NFI or WETT (Canada) certified,  
as prescribed by the local jurisdiction. It must be installed and  
operated at all times in accordance with the Installation and  
Operating instructions furnished with the product. Any alteration,  
willful abuse, accident, or misuse of the product shall nullify this  
warranty.  
•
This warranty is void if:  
a) The fireplace has been operated in atmospheres contaminated  
by chlorine, fluorine, or other damaging chemicals.  
b) The fireplace has been subjected to prolonged periods of  
dampness or condensation  
•
•
This warranty is non-transferable, and is made to the original  
owner, provided that the purchase was made through an  
authorized supplier of Vermont Castings branded CFM  
products.  
c) Any damages to the fireplace, combustion chamber, heat  
exchanger or other components due to water, or weather  
damage, which is the result of but not limited to, improper  
chimney/venting installation.  
Parts covered under the Limited Lifetime Warranty will be  
covered for the lifetime of the appliance up to a maximum  
of seven (7) years after CFM discontinues the model. The  
maximum amount recoverable under this warranty is limited  
to the purchase price of the product and, if CFM is unable to  
provide replacement or repair in an expedient and cost effective  
manner, CFM may discharge all obligations under this warranty  
by refunding the purchase price of the product.  
d) Any alteration, willful abuse, accident, or misuse of the product  
has occurred.  
IF WARRANTY SERVICE IS NEEDED...  
Contact your installing Vermont Castings dealer. Make  
sure you have your warranty, your sales receipt, the model  
number and serial number of your CFM product. If you’re  
the installing dealer is unknown or unable to provide  
necessary parts or service, a list of Authorized Vermont  
Casting dealers can be located on the internet at www.  
vermontcastings.com  
•
Any labor and related repair charges relating to the cost and  
expenses of replacing or repairing defective components  
under the Limited Lifetime Warranty are not covered, except as  
provided for under the Basic One-Year Warranty.  
20012734  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CFM Corporation  
2695 Meadowvale Blvd. • Mississauga, Ontario, Canada L5N 8A3  
800-668-5323 • www.cfmcorp.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

TC electronic SDN BHD Home Theater System Master X3 User Manual
Teac CD Player E24E User Manual
Timex Heart Rate Monitor W265 User Manual
Toastmaster Convection Oven MH36 User Manual
Toshiba Computer Drive HDD2184 User Manual
TP Link Network Router TL WR543G User Manual
TRENDnet Computer Drive TEW 624UB User Manual
Tricity Bendix Freezer UF400 User Manual
Viking Oven RDDOE306 User Manual
Vornado Electric Heater PVH User Manual