CHT-15
Owner's Manual
Audio/Video Subwoofer System
Download from Www.Somanuals.com. All Manuals Search And Download.
Congratulations!
Congratulations on your purchase of a Velodyne subwoofer system. This
system represents the state of the art in low frequency reproduction. Read
and follow the instructions below to insure safe and proper system
operation.
Warning!
To prevent fire or shock hazard, do not expose this equipment to rain or
moisture. To avoid electrical shock, do not open speaker enclosure or amp
chassis cover. Please observe all warnings on the equipment itself. There
are no user serviceable parts inside. Please refer all service questions to
your authorized Velodyne dealer.
Prior to installation
Please unpack the system carefully. Remove all staples used to seal the
carton as they can scratch the cabinet. Please save the carton and all
packaging materials for future use. Record the serial number in the space
provided on the warranty card for future reference.
Product Features and Controls
● Built-in 300 watt (RMS) power amplifier
● Subwoofer Direct - switchable crossover bypass
● Adjustable (40 to 120Hz) low-pass crossover
● Selectable (80 or 100Hz) high-pass crossover
● Line-level inputs & outputs
● Speaker-level inputs & outputs
● Signal sensing auto turn on/off with bypass option
● Variable volume control
● Variable phase control (0 to 180 degrees)
● Dual staggered low-pass crossover; 12dB/octave initial, 24dB/octave
ultimate
● Anti-clipping circuit
● Over excursion protection
continued. . .
☞
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Your new subwoofer system provides for a number of installation options.
Read all the installation information below in order to determine which
installation option is best for your system. Remember to perform all
installation procedures with system power turned off.
Inputs
Your new subwoofer is equipped
inputs. Use the LINE-IN jacks when connecting your subwoofer to a pre-
amp, signal processor,
jacks connect directly t
receiver. Your ampli
when you use these inputs because of their high impedance. Note:Do not
use both LINE-IN and FROM AMPLIFIER inputs simultaneously.
Volume control
This control allows you to
main speakers in your system. This control should be set to achieve similar
volume level from both the main speakers and subwoofer.
Low-pass crossover
Both sets of inputs sum the left and right c
resulting signal is passe
being amplified. The cr
of the subwoofer's frequency response from 40 to 120 Hz. The subwoofer's
response will begin rolling off above the frequency you set this control to.
You should set the crossover frequency to obtain a smooth and seamless
transition from the subwoofer to t
main speakers are s
may wish to choo
would with larger speak
larger speakers, you might start with th
Subwoofer Direct
A bypass switch is also provided if you wish to use an external crossover.
If you are not using an external crossover, we recommend that you use the
one provided within the unit for optimum performance.
☞
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Phase adjustment- 0˚ to 180˚
This control allows you to "delay" the phase of the subwoofer's output
signal up to 180˚ to correct for any possible mismatch & resulting
cancellation between the subwoofer and your main speakers/amplifier.
To adjust, simply listen to the system with music playing. Then rotate the
knob from one end to the other and listen for a change in low frequency
output. The correct position will have a greater amount of apparent low
frequency output.
Auto turn on function
With this function in the "auto" position, your CHT-15 can be safely left
with the main power switch on continuously. The subwoofer will turn
itself on automatically when an audio signal is present. If no signal is
present for approximately 10 minutes, the unit will switch to standby
mode. While in standy mode, your subwoofer will draw very minimal
power. This function can be disabled by leaving the switch in the "on"
position.
High pass crossover switch
This switch selects the frequency for the high pass crossover. This
crossover is functional on both line-level and speaker-level outputs.
Smaller speakers with limited low frequency output may prefer the higher
100Hz setting which will reduce the low frequencies sent to them. Larger
speakers with greater low frequency output may be able to handle the 80Hz
setting without strain.
Power switch
The master power switch is located on the right half of the unit. This rocker
style switch is the main on/off for the unit. This switch should be set to
position 1 for on (up), 0 for off (down).
Line-level connection
Figure 1, on page 5, shows connection to a pre-amplifier's main outputs
and returning them to your amplifier inputs.
When installed in this fashion, your satellite speakers will be crossed over
at 80/100Hz which removes the lower bass from your amplifier and
speakers, enabling them to do a better job reproducing high frequencies.
continued. . .
☞
4
Download from Www.Somanuals.com. All Manuals Search And Download.
By utilizing this method, you will have a bi-amplified system, gaining
improved power and headroom for your system.
Figure 1: Installation using line-level (line in) inputs
PRE-AMP
AMPLIFIER
MAIN OUTPUTS
RIGHT LEFT
MAIN OUTPUTS
MAIN INPUTS
RIGHT LEFT
RIGHT
LEFT
TO SATELLITE SPEAKERS
Subwoofer outputs
The Velodyne subwoofer is designed to operate using the full range audio
signal for input when using the built-in crossover. Many home theater
processors/receivers (Dolby Digital, DTS, THX) have a "subwoofer out"
jack that is internally filtered and designed to be used with a powered
subwoofer.
In these installations, you may bypass the internal crossover in either the
processor or the Velodyne subwoofer. In some installations, it may be
beneficial to have a steeper ultimate crossove slope. To do this, you can
use both your processor's crossover and the internal crossover in your
Velodyne sub. You should stagger the frequencies (i.e., 120Hz sub, 80Hz
processor) for best results.
☞
5
Download from Www.Somanuals.com. All Manuals Search And Download.
To bypass the subwoofer's internal crossover when the unit is being fed
a low pass signal from another crossover, simply locate the switch marked
X-over, OUT - IN on the rear panel of the subwoofer and set to the OUT
position. This will eliminate the internal crossover from the signal path.
Note. . .
If not using an external crossover, you should use the built-in crossover
for optimal performance. When using a single channel input signal
(such as a surround sound processor's subwoofer out, or LFE) the auto
on/off circuit sensitivity will be affected. When one input channel is
used instead of two, the unit will see lower signal levels present at the
inputs. This may cause the unit to turn off when listening at low volume
levels. If this occurs, simply use a "Y" adapter (available from most
dealers) to allow your processor's single sub line to be fed into both L&R
inputs. The use of a "Y" adapter will also make the unit turn on at lower
signal levels.
Speaker-level connection
Figure 2 shows an easy way to connect your Velodyne subwoofer directly
to your receiver or integrated amplifier.
When connected in this fashion, your satellite speakers will be crossed
over at 80/100Hz, which removes the lower bass from your speakers,
enabling them to do a better job reproducing high frequencies.
You may also connect your satellites directly to your receiver or amplifier
along with the subwoofer, if you wish to bypass the internal high-pass
crossover.
Caution!!!
To avoid damage to your main amplifier, be sure to maintain correct
polarity when making all connections. Red (positive) to red, and black
(negative) to black. Be sure that all connections are tight, and that there
are no loose strands or frayed wires.
continued. . .
☞
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2: Installation using speaker-level (from amplifier) inputs
MAIN OUTPUTS
(speaker-level)
INTEGRATED AMP / RECEIVER
Interconnect cables
When installing your new Velodyne subwoofer using the line level
connections, you should always use shielded phono cables. There are
many decent cables available today, most any of which will work
perfectly well. We do recommend that you keep the length of cable as
short as possible to avoid any potential noise problems.
When using speaker level connections, use a decent quality speaker cable
that mates well with the connectors. Be very careful to avoid any loose
strands or frayed wires which may result in a short, possibly causing
damage to your equipment. Cables of extremely large size are typically
not required. Extremely large gauge wire may not properly fit in the
binding posts, resulting in a poor connection and possible short circuits.
☞
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Placement
True subwoofers operate at extremely low frequencies which are primarily
omni-directional. While it is recommended that the subwoofer be placed
on the same plane as the satellite speakers, room and system conditions
often dictate otherwise. Keep in mind that frequency response and output
level can be drastically influenced by placement, depending on the
acoustic properties of the listening room. Typically, the optimum location
for a subwoofer is tucked away in a corner of your listening room. This
location will usually offer the greatest output levels and optimum low
frequency extension. The worst location for a subwoofer it typically far
away from any walls, and close to the center of your room. Avoid these
locations when possible. When using a pair of Velodyne subwoofers in
stereo, it is preferable to place each subwoofer by the satellite of the same
channel. Typically, a minimum distance of 2 to 3 feet from your TV to
the subwoofer will be adequate to avoid any magnetic interferance.
Caution!
This subwoofer has electronics built into the cabinet. Do not place the
cabinet next to sources of heat such as furnace registers, radiators, etc.
Do not place the unit near sources of excessive moisture, such as
evaporative coolers, humidifiers, etc. The power cord should be routed
in such a way that it will not be walked on, pinched, or compressed in
any way that could result in damaging the insulation or wire.
Although measures have been taken to shield the magnetic structure of
your subwoofer, Velodyne does not recommend that the subwoofer be
placed directly above, below, behind, or next to your TV or video
monitor. Distortion of the picture may still occur due to stray magnetic
fields.
Care of your subwoofer
Do not use any harsh detergents or chemicals to clean the cabinet.
Abrasives, detergents, or cleaning solutions may damage the finish on the
cabinet. We recommend using a damp cloth to clean the cabinet.
During normal conditions, the subwoofer may be left on continuously
without any problems. The unit is equipped with a signal sensing turn on/
off that will automatically turn on the unit when a signal is present at the
continued. . .
☞
8
Download from Www.Somanuals.com. All Manuals Search And Download.
inputs and turn off the unit after several minutes when there is no longer
any signal at the inputs.
If you plan to leave the sub unused for an extended period of time, we
recommend that you turn off the unit by the master power switch on the
rear panel.
Troubleshooting and Service
Before seeking service for your subwoofer, please re-check all settings.
Following is a simple troubleshooting guide to assist you.
1. Verify unit is plugged in and power outlet used is active and supplying
proper voltage?
2. Is power switch on?
3. Is auto turn on/off set pro
4. Is unit receiving an input signal from yo
5. Have all controls on subwoofer (volume,
properly set?
6. If unit has been running at h
one of the protection circuits may be engaged.
7. Is the built-in amplifier extremely hot to the touch? If so, allow the
built-in amplfier to cool before turning power on again.
If the protection circuitry is active, the
operating parameters return to normal. Under more serious conditions, the
unit may shut off completely. Normal operation will return upon cooling,
but you may be required to turn the power off and then on again to reset the
unit.
The following conditions require service by a qualified technician:
1. The power cord has become damaged.
2. The unit does not appear to operate normally or exhibits a marked
change in performance.
3. The unit has been exposed to water.
4. Some part of the cabinet or circuitry is physically damaged.
Thank you for purchasing a Velodyne!
☞
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Cabinet (H,W,D)
CHT-15
21" x 18.5" x 22.75"
23Hz-120Hz +/- 3 dB
Frequency Response
High Pass Crossover
80Hz or 100Hz
(6 dB/octave slope)
Low Pass Crossover
Amplifier (Class A/B)
Woofer
40Hz -120Hz (12 dB/octave, 24 dB ultimate)
750 watts/300 watts RMS power
15" forward firing
Magnet
70 oz.
Voice Coil
Inputs
2 - 1/2" copper
Line-level & speaker-level
Line-level & speaker-level
Two years (parts & labor)
83 lbs. (approx.)
Outputs
Warranty
Weight
Specifications are subject to change without notice.
FOR YOUR RECORDS. . .
DATE PURCHASED __________________________________
DEALER ______________________________________________
SERIAL # _____________________________________________
*NOTE: Please complete and return your warranty card within ten (10) days.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
"If you know subwoofers, you know about Velodyne."
- Corey Greenberg
Home Theater Technology/February 1995
"It delivered room-shaking bass and dramatically demonstrated the
effectiveness of a single subwoofer placed to one side of the room."
- Julian Hirsh
Stereo Review, January 1997
Other Velodyne Subwoofer Products:
F Series
FSX-12 II BV
VLF Series
VLF-810
VLF-1012
SPL Series
SPL-800
HGS Series
HGS-10
SPL-1000
SPL-1200
HGS-12
HGS-15
HGS-18
Velodyne Acoustics, .
1070 Commercial St. Suite #101
San Jose, CA 95112
408.436.7270 voice
408.436.7276 fax
E-mail: techhelp@
Printed on recycled paper.
63-CHT15 RevA 15JUN01
Download from Www.Somanuals.com. All Manuals Search And Download.
|