TM
VECTOR MANUFACTURING, Ltd.
4140 S.W. 28TH WAY
Ft Lauderdale, Fl 33312
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIO N :
• DO NOT SUBMERGE IN WATER. This unit is not waterproof-
it is water resistant
• Do not recharge with other than supplied AC and DC recharge
adapters
• Do not overcharge battery
• This spotlight produces high levels of heat when operating -
DO NOT TOUCH THE SPOTLIGHT LENS WHEN THE SPOTLIGHT IS
ON
• Keep spotlight lens away from combustible materials
when spotlight is ON
INTRODUCTION . . . . . . . . . . . . . . . . . . 1
FEATURES . . . . . . . . . . . . . . . . . . . . . . . 2
SPOTLIGHT OPERATION . . . . . . . . . . . . 3
AREA LIGHT OPERATION . . . . . . . . . . . .3
CORDED OPERATION . . . . . . . . . . . . . . 3
CHARGING THE BATTERY
WITH 110-VOLT AC ADAPTER . . . . . . . 4
BULB REPLACEMENT . . . . . . . . . . . . . . . .5
USAGE TIPS
FUSE REPLACEMENT
SPECIFICATIONS
BATTERY DISPOSAL . . . . . . . . . . . . . . . .8
WARRANTY INFORMATION . . . . . .9 & 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
IN TRO DUCTIO N
Congratulations on selecting the new Vector™ ULTRA SPORT SPOT® - the most powerful
handheld rechargeable spotlight available. With 2 million candlepower strength, it’s clean,
tight beam carries up to 2 miles and focuses 50% more light on the target at a distance of
1000 ft. (compared to similar products).
When fully charged the ULTRA SPORT SPOT® provides up to 30 minutes of cordless, ultra-
bright illumina tion, using the la test ultra -white, high power type
of halogen technology.
The ULTRA SPORT SPOT® has many features that make it the best choice for home or
outdoor use - whenever and wherever you need to light up the darkness. It can be used
cordless with its rechargeable, removable battery pack; or corded, using any vehicle’s
12-volt DC universal cigarette lighter receptacle.
The removable, rechargeable battery pack is easily recharged from a 12-volt DC or
110-volt AC power source, I.E.: a vehicle’s 12-volt DC battery, or a standard 110-volt AC
household power socket.
The replaceable 12-volt H3 type quartz halogen bulb powerful beam of ultra-white light
even penetra tes ra in, fog, a nd smoke, ma king it a n excellent source of
emergency lighting during utility power outages. With proper care and use, it will give you
years of dependable, supplemental lighting.
FEATURES
• LATEST TECHN O LO GY - HIGH IN TEN SITY, ULTRA-W HITE H3 TYPE
HALO GEN BULB FO R BRIGHTER ILLUMIN ATIO N USIN G LESS PO W ER
• CLEAN , TIGHT BEAM CARRIES UP TO 2 MILES!
• CO MPUTER-DESIGN ED PARABO LIC REFLECTO R EN HAN CES LO N G
DISTAN CE VISIBILITY
• REMO VABLE BATTERY PACK RECHARGES FRO M HO ME O R VEHICLE
(ADAPTERS IN CLUDED)
• TAKE AN YW HERE - USE CO RDLESS FO R UP TO 3 0 MIN UTES O F
CO N TIN UO US LIGHT (W HEN FULLY CHARGED)
• USE CO RDED - PLUG IN TO AN Y 1 2 -VO LT DC O UTLET FO R EXTEN DED USE
W ITH O R W ITHO UT BATTERY IN STALLED.
• RUGGED, W EATHERPRO O F, ABS CO N STRUCTIO N
• CO MFO RTABLE, PISTO L-GRIP HAN DLE W ITH LO CKIN G O N / O FF TRIGGER
• N EW SW IVEL HAN DLE/ STAN D FO R EASY PO RTABILITY AN D STO RAGE
• RECHARGE AN D USE FRO M 1 2 VO LT DC O UTLET
• AREA LIGHT IN HAN DLE LIGHTS UP TO 1 4 HO URS O N FULL
BATTERY CHARGE
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Please read and follow all safety warnings and instructions carefully before using the
ULTRA SPORT SPOT®
REPLACEABLE, ULTRA-WHITE,
H3 TYPE HALOGEN BULB
Figure A.
REMOVABLE, RECHARGEABLE
SEALED LEAD ACID BATTERY PACK
™
Ltd.
NG,
TURI
FAC
NU
MA
T
SPO
RT
PO
S
r
e
RA
w
o
T
P
le
UL
d
n
a
C
0
0
,0
0
0
,0
1
TRIGGER
SWITCH
LOCK
OCK
L
K
C
O
L
N
U
CONVENIENT ON/ OFF
TRIGGER SWITCH
BATTERY
SAFETY
COVER
AREA LIGHT
EXTRA-LONG 10 FOOT POWER CORD
WITH FUSE 12-VOLT DC CIGARETTE
LIGHTER TYPE PLUG
AREA LIGHT
SWITCH
110-VOLT AC HOUSEHOLD OUTLET
BATTERY CHARGER ADAPTER
2
Download from Www.Somanuals.com. All Manuals Search And Download.
SPO TLIGHT O PERATIO N
1. Before cordless use, charge battery fully with 110-volt AC battery charger adapter (see
instructions on page 4). With a full charge, the ULTRA SPORT SPOT® will provide up to 30
minutes of continuous, cordless illumination.
2. Press trigger switch to turn beam ON.
3. Release trigger switch beam to turn OFF.
4. For a continuous beam, press trigger and slide the lock switch up into the lock position.
Slide the lock switch down into the unlock position to turn off beam (Figure B.)
5. When light dims, battery charge is low. Do not allow battery to completely
discharge. Fully recharge battery as soon as possible after each use.
AREA LIGHT O PERATIO N
The long lasting area light in the handle is controlled by
a small button type switch located in the handle. Press
the button to turn on the light. With the
battery fully charged, the area light can continuously
operate for 14 hours. When the unit is plugged into an
Figure B.
external DC source, the area light can operate as long
as 12 volts is available.
The handle can be positioned so that it acts as a stand.
The light can rest on the handle and the area light
assembly can be swiveled to provide the best lighting.
™
Ltd.
NG,
URI
ACT
F
NU
MA
OT
SP
P
Press and release the area light button to turn it off.
T
d
OR
P
S
r
e
RA
w
o
T
le
UL
n
a
C
0
0
,0
0
0
,0
1
CK
O
L
CK
O
NL
U
Area Light
Switch
Area Light
WARN IN G:
Never leave the spotlight laying lens-down on any surface when beam is turned on. Contact
could ignite or burn surfaces such as seat cushions, carpeting, tables, etc. and pose a serious
threat of fire. When beam is turned off, ALWAYS keep the lock switch in the lock position to
avoid accidentally turning on the beam.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CO RDED O PERATIO N
NOTE: During corded operation, the battery may be left in the unit, and will charge while the
spotlight or area light are being used. A full charge takes about 3-4 hours using the DC
method or the battery may be removed for charging (using the 12-volt 110-volt AC method.)
1. Insert 12-volt DC power plug into DC adapter plug at bottom of handle (Figure C).
2. Plug the other end into any vehicle’s cigarette lighter receptacle or other compatible 12-volt
DC power source.
CHARGIN G THE BATTERY W ITH 1 1 0 -VO LT AC ADAPTER
The 110-volt AC adapter provides a much more effective charge compared to charging with a
12-volt DC power source. Because the battery pack is removable, you can charge the battery
at home while your ULTRA SPORT SPOT® is being operated with the 12-volt DC power cord.
For extended use, we recommend purchasing an additional battery as back-up. Call Vector™
Customer Service department at 954-584-4446 or toll free at 866-584-5504
1. Slide the battery pack cover towards the handle. Completely remove the cover and
set it aside.
Fig u re D.
2. The battery pack can be removed from the light by carefully tapping the unit and
freeing the battery.
3. Make sure the battery pack contacts are not shorted to any metal objects.
Plug the AC adapter into the battery and charge for eight hours. If battery is severely
discharged then charge it for 12 hours. DO NOT OVERCHARGE BATTERY.
Figure D.
Figure C.
10 AMP FUSE
DC ADAPTER PLUG CONNECTION
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTIO N : Th e b a tte ry sa fe ty co ve r m u st b e in p la ce w h ile ch a rg in g to
p re ve n t a sh o rt circu it if th e co n ta ct p o in ts a re a ccid e n ta lly p la ce d
a g a in st m e ta l.
4. Plug the 110-volt AC adapter into the battery (Figure E.) and plug into any standard
110-volt AC wall outlet.
Figure E.
BATTERY SAFETY CO VER
5. Battery will be fully charged after 18 hours. DO NOT charge more than 24 hours or you
may damage the battery.
6. Unplug adapter, then remove battery safety cover.
7. Replace battery into spotlight with metal contact points facing in.
8. Replace battery cover. Fasten screw by turning clockwise with your fingers.
BULB REPLACEMEN T
N O TE: Use o n ly Ve cto r™ u ltra -w h ite , H3 1 2 -vo lt Ha lo g e n re p la ce m e n t
b u lb , d e sig n e d sp e cifica lly fo r th e ULTRA SPO RT SPO T®. Use o f a n y o th e r
b u lb co u ld re su lt in p o o r p e rfo rm a n ce a n d d a m a g e to y o u r sp o tlig h t.
Ple a se re a d a ll in stru ctio n s b e fo re p ro ce e d in g w ith b u lb re p la ce m e n t.
1. Disconnect the spotlight from corded power source and remove battery.
2. Slide the protective rubber bezel forward and remove it.
3. Using a small phillips screwdriver, remove the screws at the top and the bottom of the
front housing (Figure F). Place spotlight lens-down on flat surface.
4. Grasp the spotlight handle and gently lay the housing next to the lens, being careful not
to pull apart wire connections.
N O TE: DO N O T TO UCH th e g la ss b u lb o r th e in sid e o f th e re fle cto r w ith
fin g e rs. N a tu ra l o ils fro m h a n d s ca n a d ve rse ly a ffe ct p e rfo rm a n ce o r
ca u se th e b u lb to sh a tte r w h e n h e a te d . Ha n d le th e b u lb b y its m e ta l b a se
o n ly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Push wire prongs together and push up to release (Figure G.)
6. Loosen grounding wire screw and pull bulb out by its base (Figure H.)
Figure F.
Figure H.
Figure G.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Disconnect bulb wire from its connection in the housing by holding the connector firmly and
pulling the wire straight out (Figure I.)
8. To install new bulb, hold the bulb by its metal end and insert into the reflector mounting plate.
Align the slots in the bulb base with those in the reflector mounting plate.
9. Tighten the grounding wire screw.
10. Replace wire retainer by pressing prongs together while pressing down.
11. Reconnect the bulb wire to the connector in the housing (Figure J.)
12. To reassemble, set the reflector into the front housing (laying on a flat surface). Insert the rear
housing into the front housing until grooves are aligned.
13. Replace the screws removed in step 3. Do not over tighten.
14. Slide the rubber bezel back into place (rounded edge facing front).
Figure I.
Figure J.
™
d.
,
Lt
ING
UR
ACT
NUF
MA
T
O
P
S
T
O
R
P
S
r
e
RA
ow
P
e
LT
l
U
d
n
a
C
0
0
,0
0
0
,0
1
K
OC
L
LOCK
N
U
7
Download from Www.Somanuals.com. All Manuals Search And Download.
USAGE TIPS
Fo r b e st re su lts a n d to p re ve n t d a m a g e to sp o tlig h t:
• Use only the charging devices included with your ULTRA SPORT SPOT™, or a Vector™
Manufacturing replacement. Replacement bulbs and batteries are available from our
customer service depa rtment by ca lling (954)584-4446 or ca ll toll free
866-584-5504, 9:00 am to 5:30 pm (est).
• Charge battery with AC adapter for at least 18 hours. Do not charge longer than
24 hours.
• Do not let battery run down completely. (A dim light indicates a low battery.) Recharge
battery as soon as possible after each use.
• If spotlight is not in use, charge battery at least every five months. Failure to do so will
result in damage to the battery. Always keep battery fully charged when not in use.
• Do not allow metal to touch the square metal contacts on the battery. This can cause a
short circuit that could result in fire. Always put the battery safety cover on when
battery is removed.
FUSE REPLACEMEN T
The DC plug contains a 10 amp fuse. If the fuse blows, investigate the reason and fix the
problem. Then replace the fuse. Disconnect the spotlight from the DC adapter, unscrew the
flange on the DC counterclockwise. remove the end contact and fuse. Replace the flange
and tighten clockwise. DO NOT OVERTIGHTEN FLANGE.
FUSE
FLAN GE
CO N TACT
SPRIN G
SPECIFICATIO N S
Spotlight Bulb . . . . . . . . . . . . . . . . . . . . .H3 Proprietary, 12 Volt
Area light bulb . . . . . . . . . . . . . . . .2.6 Watt, Proprietary, 12 Volt
Battery . . . . . . . . . . . . . . . . . . . .12 Volt, 3 AH Sealed Lead Acid
AC Charger . . . . . . . . . . . .110 VAC to 12 VDC 500 mAmnbnm
BATTERY DISPO SAL
THIS UNIT CONTAINS A MAINTENANCE-FREE, NON-SPILLABLE, LEAD ACID
BATTERY WHICH MUST BE DISPOSED OF PROPERLY. SOME STATES REQUIRE
RECYCLING. DISPOSAL QUESTIONS? IN USA, CALL 1-877-288-7722
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
120 DAY LIMITED WARRANTY REGISTRATION FORM
This Vector Manufacturing, Ltd. product is warranted to the original purchaser only, for 120 days from the date of
purchase, to be free of defects in materials and workmanship. In no event will Vector Manufacturing, Ltd. be
responsible for any amount of damages beyond the retail purchase price of the product. All Vector Manufacturing, Ltd.
products must be registered within (10) days of purchase. To activate this warranty, mail the completed
registration form along with a copy of the original sales receipt to the address shown below.
TERMS OF REPAIR OR REPLACEMENT: In the event of a defective unit, return the unit to us within 30 days of the date
of purchase, and we will replace it, free of charge. If returned after 30 days but within 120 days of the purchase date
we will repair the unit or, at our option, replace it free of charge. If we repair the unit, we may use new or
reconditioned replacement parts, at our option. If we elect to replace the unit, we may replace it with a new or recon-
ditioned one of the same or comparable design. The repair or replacement unit will then be warranted under the terms
of our standard 120 day warranty. The customer is responsible for shipping charges on all returned items. During the
warranty period, Vector Manufacturing, Ltd. will be responsible for the repair or replacement cost plus the return
shipping charges.
LIMITATIONS: Implied warranties, including those of fitness for a particular purpose and merchantability (an
unwritten warranty that the product is fit for ordinary use), are limited to 120 days from the
purchase date. Vector Manufacturing, Ltd. will not reimburse for loss of time, inconvenience, loss of use of a product
or property damage caused by a product or its failure to work or any other incidental or inconsequential damages,
including personal injury.
EXCLUSION: This warranty does not cover bulbs, fuses and batteries, defects resulting from normal wear and tear
(including chips, scra tches, a bra sions, discolora tion or fa ding due to usa ge or exposure to
sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized use or repair, neglect,
misuse, abuse, failure to follow instructions for care and maintenance, fire, flood and Acts of God. If your problem is
not covered by this warranty, call our customer service facility at (954) 584-4446 for general repair information and
charges. This limited warranty is the only one that applies to this product and sets forth all the responsibilities of Vector
Manufacturing, Ltd, regarding this product. There are no warranties which extend beyond those described herein.
STATE LAW RIGHTS: Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consequential damages, so the exclusions or limitations stated herein may not apply. This
warranty gives the purchaser specific legal rights; other rights, varying from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Within 30 days of the purchase date, return the unit, along
with the dated sales receipt, to the place of purchase for immediate replacement. After 30 days, but within the 120
day warranty period, you may return the product to the address shown below. We strongly suggest that you retain the
original packaging in case you need to ship the unit. When returning a product, include your name, address, phone
number, dated sales receipt and a description of the reason for return. After repairing or replacing the unit, we will
return it to you within four weeks.
Please activate my Limited Warranty for Model VEC126
I have enclosed a copy of the original sales receipt.
Name___________________________________________________________________
Street Address ___________________________________________________________
City_________________________________ State ________ Zip code ______________
Phone _________________ Fax __________________ E-mail ____________________
Item Purchased ______________________________Date of Purchase ______________
Store Where Purchased ___________________________________________________
UPC Number from package (12 digits)_______________________________________
All Vector Manufacturing, Ltd. products must be registered within (10) days of
purchase to activate this warranty. Mail the completed registration form, along with
a copy of the original sales receipt, to:
ATTN: CUSTOMER SERVICE / VECTOR MANUFACTURING, LTD.
4140 S.W. 28th WAY
FT. LAUDERDALE, FL 33312
Download from Www.Somanuals.com. All Manuals Search And Download.
TM
3 YEAR EXTENDED WARRANTY REGISTRATION FORM
Certain Vector Manufacturing, Ltd. products are eligible to be covered to the original
purchaser only, for three (3) years from the date of purchase to be free of defects in
materials and workmanship. Vector Manufacturing, Ltd. disclaims any liability for
consequential damages. In no event will Vector Manufacturing, Ltd. be responsible
for any amount of damages beyond the amount paid for the product at retail. In the
event of a defective item, please ship the item to us, prepaid, with an explanation
of the problem, your name, address and daytime telephone number. Vector
Manufacturing, Ltd. will, at its option, replace or repair the defective part.
The following situations are not covered under this warranty:
✁
✁
Cost of shipment to Vector Manufacturing, Ltd.
Normal wear and tear, including chips, scratches, abrasions, discoloration or
fading due to usage or exposure to sunlight.
✁
✁
Damage caused by misuse, abuse, neglect, alterations, repairs by unauthorized
persons, or failure to follow recommended care and use instructions.
Bulbs and batteries.
Please activate my Extended Warranty for Model # VEC126.
Name
Street Address
City
State
Fax
Zip Code
E-mail
Phone
Item Purchased
Date of Purchase
Store where purchased
UPC Number from package (12 digits)
Form of Payment (US$12.00) Check
(payable to: Vector Manufacturing, Ltd.)
Money Order
Enclose a copy of your original sales receipt and a check or money order for US$12.00
made payable to Vector Manufacturing, Ltd., and mail to:
VECTOR MANUFACTURING, Ltd.
4140 S.W. 28TH WAY
Ft Lauderdale, Fl 33312
WARRANTY MUST BE PURCHASED WITHIN 90 DAYS OF PRODUCT PURCHASE DATE.
WARRANTY IS NON-TRANSFERRABLE AND NON-REFUNDABLE.
Download from Www.Somanuals.com. All Manuals Search And Download.
|