VEC1042MG
ONE YEAR LIMITED WARRANTY REGISTRATION FORM
™
This limited warranty program is the only one that applies to this product, and it sets forth all the
responsibilities of Vector Products, Inc. regarding this product. There is no other warranty, other than those
described herein.
This Vector Products, Inc. product is warranted, to the original purchaser only, to be free of defects in
materials and workmanship for one year from the date of purchase without additional charge. The
warranty does not extend to subsequent purchasers or users. Vector Products, Inc. will not be responsible
for any amount of damage in excess of the retail purchase price of the product under any circumstances.
Incidental and consequential damages are specifically excluded from coverage under this warranty.
This product is not intended for commercial use. This warranty does not apply to accessories or damage to
units from misuse or incorrect installation. Misuse includes wiring or connecting to improper polarity power
sources.
RETURN/REPAIR POLICY: Defective products, other than accessories, may be returned postage
prepaid to Vector Products, Inc.. Any defective product, other than accessories, that is returned to Vector
Products, Inc. within 30 days of the date of purchase will be replaced free of charge. If such a product is
returned more than 30 days but less than one year from the purchase date, Vector Products, Inc. will repair
the unit or, at its option, replace it free of charge. If the unit is repaired, new or reconditioned replacement
parts may be used, at Vector Products, Inc.’s option. A unit may be replaced with a new or reconditioned
unit of the same or comparable design. The repaired or replaced unit will then be warranted under the
terms of the remainder of the warranty period. The customer is responsible for the shipping charges on all
returned items after 30 days. During the warranty period, manufacturer will be responsible for the return
shipping charges.
TRAVELERS POWER
STATION
AC/DC RECHARGEABLE
LIMITATIONS: This warranty does not cover accessories, bulbs, fuses and batteries, defects resulting from
normal wear and tear (including chips, scratches, abrasions, discoloration or fading due to usage or
exposure to sunlight), accidents, damage during shipping to our service facility, alterations, unauthorized
use or repair, neglect, misuse, abuse, failure to follow instructions for care and maintenance, fire, flood and
Acts of God.
If your problem is not covered by this warranty, call our Technical Support Department toll free at
866-584-5504 for general repair information and charges if applicable. You may also contact us through
STATE LAW RIGHTS: This warranty gives you specific legal rights. Some states do not allow limitations on
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages,
so the exclusions or limitations stated herein may not apply. This warranty gives the purchaser specific legal
rights; other rights, which vary from state to state, may apply.
TO REQUEST WARRANTY SERVICE FOR THIS PRODUCT: Contact Vector Products, Inc. Technical Support
by telephone, fax or mail (see below). We suggest that you keep the original packaging in case you need
to ship the unit. When returning a product, include your name, address, phone number, dated sales receipt
(or copy) and a description of the reason for return and product serial number. After repairing or replacing
the unit, we will make every effort to return it to you within four weeks.
WARRANTY ACTIVATION: Please complete Warranty Activation Card and mail to Vector Products, Inc..
Enter “VEC1042MG” as Model and “Travelers Power Station” as Product Type. All Vector Products, Inc.
products must be registered within (30) days of purchase to activate this warranty. Mail the completed
registration form, along with a copy of the original sales receipt to:
ATTN.: CUSTOMER SERVICE
4140 S.W. 30th Ave., Ft. Lauderdale, FL 33312
• TOLL FREE: 866-584-5504 • FAX: 954-584-5556 •
OWNER’S MANUAL
& WARRANTY INFORMATION
IMPORTANT SAFETY INFORMATION, SAVE THESE INSTRUCTIONS
THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING THE
OPERATION AND WARRANTY OF THIS PRODUCT. PLEASE READ CAREFULLY
BEFORE USE AND RETAIN FOR FUTURE REFERENCE
RD071706
Download from Www.Somanuals.com. All Manuals Search And Download.
Protective Features
TROUBLESHOOTING
The power station monitors the following conditions:
Common Audio/Visual Problems
Problem: Buzzing Sound In Audio Systems
Some inexpensive stereo systems and boom boxes make a buzzing sound when
operated from the inverter, because the power supply in the electronic device does
not properly filter the modified sine wave produced by the inverter. The only solution
to this problem is to use a sound system that has a higher quality power supply.
Low Battery Voltage: This condition is not harmful to the power station but could
damage the power source, so the power station automatically shuts down when
input voltage drops to 10.6 volts. When this condition is corrected, the unit will
auto-reset.
Short Circuit Protection: The power station will automatically shut down when
short circuit occurs. The power station will auto-reset after removing the short circuit.
Problem: Television Interference
Figure 1
The Power Station is shielded to minimize interference with TV signals. However, in
some instances, some interference may still be visible, especially when the TV signal
is weak. Try the following to improve the picture:
1
1. Move the Power Station Inverter as far away as possible from the TV set, the
2
antenna, and the antenna cables. Use a short AC extension cord, if necessary.
2. Adjust the orientation of the antenna cables, and the TV power cord to minimize
interference.
3. Make sure that the antenna feeding the TV provides an adequate (snow-free)
signal and that high quality, shielded antenna cable is used.
Common Power Output Problems
Possible Causes
Recommendations
Battery voltage
Recharge battery or check
DC power supply.
below 10.6 volts.
Equipment being operated
draws too much power.
3
Reduce load to maximum 100 watts.
10
4
5
Inverter in thermal
shutdown condition
6
11
Allow inverter to cool down. Shutdown inverter
and ensure that there is adequate ventilation
around unit, and load is no more than 100 watts
for continuous operation.
9
7
Main fuse failed (blown).
Inverter is overloaded.
Replace fuse in DC connector.
8
Reduce load to 100 watts max. to maintain
regulation.
1. Two sealed, rechargeable lead acid batteries (included)
2. Battery charge level indicator
3. 120 volt AC output
Fuse Replacement
Replace the fuse inside of the DC charger plug with a fuse of the same type and
rating.
4. USB port – USB 5 volt source
5. 120 volt AC household recharging port – AC/DC recharge adapter
6. 12 volt DC power socket
7. 12 volt DC charger
8. 120 volt AC charger
9. Battery Status pushbutton
10. Power switch
11. Power LED indicator
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2
OPERATION OF THE POWER STATION
POWERING AND CHARGING
To turn on the Power Station, slide the power switch to ON position. The green LED
light will come on. The slide switch controls 120 volt AC output and USB 5 v dc
output; it does not control the 12 volt power socket.
Power Source Requirements/Run Times
The inverter is powered by two sealed, rechargeable lead acid batteries (included)
and can be recharged using any 12 volt DC accessory outlet or 120 volt AC
household outlet.
Using the USB Port
Note: This unit is shipped in a partially charged state. Initially charge unit using the
AC charger. To check the battery level, press the Battery Status Pushbutton (see
Figure 1). Charge until Battery Status Displays green; LED lights when the
Battery Status pushbutton is pressed. Charge after each use using the AC/DC
Recharge Adapter (see Figure 1 and follow directions).
The USB port is located at the front of the Power Station (see Figure 1).
1. Plug the USB cable (5 volt DC 0.5 amp max) into the USB port to operate or
recharge the USB powered device.
2. Operate the device according to the manual.
Operating Tips
• Do not allow water or other liquids to come into contact with the power station.
• Surrounding air temperature should be between -20°C and 40°C – ideally
between 15°C and 25°C (60-80°F). Keep the power station away from direct
sunlight, when possible.
• Keep the area surrounding the power station clear to ensure free air circulation
around the unit. Do not place items on or over the power station during operation.
The unit will shut down if the internal temperature gets too hot. Turn the switch off
and turn it on again after the unit cools down.
Charging Using the 120 Volt AC Recharge Adapter
1. Make sure all connected appliances are turned OFF.
2. The 120 volt AC recharge port is located at the rear of the power station.
3. Connect the AC charger to a 120 VAC, 60 Hz power source.
4. Recharge for 8 hours maximum or until the green LEDs light.
5. After AC recharging, wait 5 minutes before using item.
CAUTION
• Do not use the power station near flammable materials or in any locations that
may accumulate flammable fumes or gases. This is an electrical appliance that
can briefly spark when electrical connections are made or broken.
DO NOT OPERATE ANY DC APPLIANCES THROUGH THE POWER
STATION’S ACCESSORY OUTLET WHEN THE AC/DC RECHARGE
ADAPTER IS CHARGING THE UNIT.
Rated versus Actual Current Draw of Equipment
Using the DC Recharge Adapter
The VEC1042MG can be simultaneously charged and operated from a 12 volt DC
source. Make sure the 12 volt source can supply minumim 10 amperes of current.
To check the battery level, press the Battery Status Pushbutton. Charge until Battery
Levels Display green; LED lights when the Battery Status pushbutton is pressed.
• Most electrical tools, appliances, electronic devices and audio/visual equipment
have labels that indicate the power consumption in amps or watts. Be sure that
the power consumption of the item to be operated is below 100 watts. If the
power consumption is rated in amps, simply multiply by the AC volts (120) to
determine the wattage.
• Resistive loads are the easiest for the Power Station to run; however, it will not run
larger resistive loads (such as electric stoves and heaters) which require far more
wattage than the power station can deliver. Inductive loads (such as TVs and
stereos) require more current to operate than do resistive loads of the same
wattage rating. For safety reasons, the unit will simply shut down if it is
overloaded. To restart the unit, simply remove the load, turn the unit off, and turn
it on again.
1. Locate the 12 volt DC power socket on the back of the Power Station (see Figure
1).
2. Connect the DC charger to a 12 volt DC source that can supply at least 10
amps of current.
3. Plug the other end of DC charger to the 12 volt DC power socket.
4. Recharge for 3-4 hours maximum or until the green LED lights when the battery
Status Display pushbutton is pressed.
Note: This power station will not operate appliances and equipment that generate
heat, such as hair dryers, electric blankets, microwave ovens, and toasters.
5. After recharge, disconnect the Adapter from the external charging/power
source then disconnect the connector from the DC Recharge Port.
Note: That some vehicles must have the ignition turned on to power the vehicle’s
accessory outlet.
WARNING
NEVER SIMULTANEOUSLY CONNECT AC/DC AND DC/DC CHARGERS
TO POWER STATION
Download from Www.Somanuals.com. All Manuals Search And Download.
3
4
|