6-Port SATA II 150 PCI Host
Card w/RAID
User Manual
Model: UGT-ST310R
All brand names and trademarks are properties of their respective owners.
w w w . v a n t e c u s a . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
•
•
•
•
Silicon Image SiI3114 SATA controller chip
Compliant with PCI Specification, Rev. 2.3, 32-bit, 33/66Mhz
Compliant with Serial ATA 1.0 specification
Provides four independent channels to support up to four
Serial ATA drives
•
Supports RAID0 (striping), RAID1 (mirroring), RAID5 (Parity
RAID), RAID 0+1(mirroring + striping) and Concatenation
(JBOD), Individual Mode
•
•
•
HDDs function normally when not in RAID sets
Supports SATA up to 150MB/Sec
Supports Windows® 2000, XP/2003 32/64 bit, Vista 32/64bit
Bus Interface
z
PCI Bus 32 bit
Connectors
z
z
4 x internal SATA connectors
2 x external eSATA connectors
Package Contents
z
z
z
z
1 x 6-Port SATA II 150 PCI Host Card w/RAID
1 x Driver CD
2 x SATA Data Cable
1 x User’s Manual
UGT-ST310R
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
System Requirements
z
z
Pentium-class computer with one available PCI slot
Windows® 2000, XP/2003 32/64bit, Vista 32/64bit
Hardware Description
G (Jumper Settings)
JP
Description
Active Port
J1-J4 1-2 close
Enable SATA Connector
F
2-3 close
Enable SATA Connector
C
J5-J8 1-2 close
2-3 close
Enable SATA Connector
E
Enable SATA Connector
D
UGT-ST310R
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: There are six SATA ports in 6-Port SATA II 150 PCI Host
Card w/RAID. We name these ports from A through F. Ports A to
D are internal SATA ports. Ports E and F are external SATA ports.
Changing the jumper settings allows you to select between
external and internal ports to use. By default, Port A, B, C and D
are working.
Hardware Installation
1. Turn Off the power to your computer and any other
connected peripheral devices.
2. Unplug the power cord form the back of the computer.
3. Remove your computer’s cover.
4. Remove the slot bracket from an available PCI slot.
5. To install the card, carefully align the card’s bus connector
with the selected PCI slot on the motherboard. Push the
board down firmly, but gently, until it is well seated.
6. Replace the slot bracket’s holding screw to secure the card.
Device Connection
The 6-Port SATA II 150 PCI Host Card w/RAID is a four channel
Serial ATA controller that supports up to four Serial ATA hard disk
drives. It is recommended to use identical hard drives for all
RAID configurations.
1. Install your hard disk drive(s) in chassis.
2. Connect the Serial ATA hard disk drive to the system power
supply using the included Serial ATA power cable.
3. Connect one end of the Serial ATA cable to the hard disk
UGT-ST310R
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
drive.
4. Attach the other end of the Serial ATA cable to the Serial
ATA controller on the 6-Port SATA II 150 PCI Host Card
w/RAID.
5. Follow the same instructions to connect up to four hard
drives. Device connection is now complete.
6. Replace the computer cover and reconnect the power cord.
RAID Arrays
RAID Arrays are setup in the 6-Port SATA II 150 PCI Host Card
w/RAID’s BIOS.
RAID 0 (Striping)
This RAID array to be used on New/Blank hard drives. Striping
will destroy existing data on the hard drive. Auto Configuration
is recommended. For applications that require custom chunk
size, Manual Configuration is offered.
Auto configuration (recommended)
The default chunk size is 64k when selecting Auto
configuration.
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
UGT-ST310R
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select RAID0, then press Enter.
4. Select the number of drives then press Enter.
5. Select Auto configuration, then press Enter.
6. Input the RAID size, press Enter.
7. When asked Are You Sure (Y/N)?, press Y to accept.
8. Press Ctrl+E to exit the BIOS.
9. When asked Are you sure to exit (Y/N)?, press Y to exit
and reboot.
10. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
Manual configuration
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. Select RAID0, then press Enter.
4. Select the number of drives then press Enter.
5. Select Manual configuration then press Enter
6. Select chunk size from 8k, 16k, 32k, 64k or 128k, then
press Enter.
7. Select the first drive, press Enter.
8. Select the second drive, press Enter.
9. If applicable select the 3rd and 4th drives pressing enter
after each selection.
10. Input the RAID size, press Enter.
11. When asked Are You Sure(Y/N)?, press Y to accept.
12. Press Ctrl+E to exit the BIOS.
13. When asked Are you sure to exit(Y/N)?, press Y to exit
and
reboot.
14. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
UGT-ST310R
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
RAID 1 (Mirror)
For New/Blank Hard Drives
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. At the next screen select RAID1 then press Enter.
4. Select Auto configuration, then press Enter.
5. Input the RAID size, press Enter.
6. When asked Are You Sure(Y/N)?, press Y to accept.
7. Press Ctrl+E to exit the BIOS.
8. When asked Are you sure to exit(Y/N)?, press Y to exit
and reboot.
9. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
For Existing Hard Drives with Data
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. At the next screen select RAID1 then press Enter.
4. Select Manual configuration, then press Enter.
5. Select the Source drive, press Enter.
6. Select the Target drive, press Enter.
7. Select Create with data copy, then press Enter.
8. Select online copy, then press Enter.
Note: Selecting Online Copy builds the mirror while in
Windows. Selecting Offline Copy builds the mirror before
exiting the RAID BIOS.
UGT-ST310R
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Input the RAID size, press Enter.
10. Press Ctrl+E to exit the BIOS.
11. When asked Are you sure to exit(Y/N)?, press Y to exit
and reboot.
Note: If during boot the RAID BIOS reports an RAID1 set is in
Rebuild status, The rebuild will continue after boot
sequence is complete, disregard the message, continue
booting, and let the Mirror rebuild.
Rebuilding a Failed Mirror Set
When a failure to one member occurs, you will be notified either
by the RAID BIOS during boot or by the SATARAID5 GUI while
in Windows. The steps below will guide you in rebuilding a failed
mirror set.
1. Replace the failed drive with one of equal or greater
capacity, then start the computer.
2. During boot press Ctrl+S or F4 to enter the RAID BIOS.
3. Select Create RAID Set then press Enter.
4. Select SPARE DRIVE then press Enter.
5. Select the replacement drive then press Enter.
6. When asked Are You Sure(Y/N)?, press Y to confirm.
7. Press Ctrl+E to exit.
8. When asked Are you sure to exit(Y/N)?, press Y to exit.
RAID 0+1 (Mirroring + Striping)
This RAID array to be used on New/Blank hard drives, do not
UGT-ST310R
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
use existing hard drive(s) with data. To create a RAID 0+1 set
four hard drives are required.
Auto configuration (recommended)
The default chunk size is 64k when selecting Auto
configuration.
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. Select RAID10, then press Enter.
4. Select Auto configuration, then press Enter.
5. Input the RAID size, press Enter.
6. When asked Are You Sure(Y/N)?, press Y to accept.
7. Press Ctrl+E to exit the BIOS.
8. When asked Are you sure to exit(Y/N)?, press Y to exit
and reboot.
9. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
Manual configuration
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. Select RAID10, then press Enter.
4. Select the number of drives then press Enter.
5. Select Manual configuration then press Enter.
UGT-ST310R
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Select chunk size from 8k, 16k, 32k, 64 or 128k, then press
Enter.
7. Select the first drive, press Enter.
8. Select the second drive, press Enter.
9. Select the third drive, press Enter.
10. Select the fourth drive, press Enter.
11. Select Create without data copy then press Enter.
12. Input the RAID size, press Enter.
13. When asked Are You Sure(Y/N)?, press Y to accept.
14. Press Ctrl+E to exit the BIOS.
15. When asked Are you sure to exit(Y/N)?, press Y to exit
and reboot.
16. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
RAID 5 (Parity)
This RAID array to be used on New/Blank hard drives. Striping
will destroy existing data on the hard drive. Auto Configuration
is recommended. For applications that require custom chunk
size, Manual Configuration is offered.
Auto configuration (recommended)
The default chunk size is 64k when selecting Auto
configuration.
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS
2. At the next screen select Create RAID Set, then press
UGT-ST310R
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Enter.
3. Select RAID5, then press Enter.
4. Select the number of drives then press Enter.
5. Select Auto configuration, then press Enter.
6. Input the RAID size, press Enter.
7. When asked Are You Sure(Y/N)?, press Y to accept.
8. Press Ctrl+E to exit the BIOS.
9. When asked Are you sure to exit(Y/N)?, press Y to exit
and reboot
10. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
Manual configuration
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. Select RAID5, then press Enter.
4. Select the number of drives then press Enter.
5. Select Manual configuration then press Enter.
6. Select chunk size from 8k, 16k, 32k, 64 or 128k, then press
Enter.
7. Select the first drive, press Enter.
8. Select the second drive, press Enter.
9. Select the third drive, press Enter.
10. If applicable select the 4th drive pressing enter after each
selection.
11. Input the RAID size, press Enter.
12. When asked Are You Sure(Y/N)?, press Y to accept.
13. Press Ctrl+E to exit the BIOS.
14. When asked Are you sure to exit(Y/N)?, press Y to exit
UGT-ST310R
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
and reboot.
15. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
CONCATENATION (JBOD)
This RAID array allows you to use one, two, three or four hard
drives to a array. It does not provide any data protection or
performance improvement but can be useful for utilizing leftover
space on disks.
1. As the BIOS boots press Ctrl+F4 or F4 when prompted to
enter the RAID BIOS.
2. At the next screen select Create RAID Set, then press
Enter.
3. Select CONCATENATION, then press Enter.
4. Select the number of drives then press Enter.
5. Select the first drive, press Enter.
6. If applicable select the 2nd, 3rd, 4th drive pressing enter
after each selection.
7. When asked Are You Sure(Y/N)?, press Y to accept.
8. Press Ctrl+E to exit the BIOS.
9. When asked Are you sure to exit(Y/N)?, press Y to exit
and reboot.
10. Continue with FDISK and FORMAT steps as if you were
installing a conventional hard drive.
Deleting RAID Arrays
1. As the BIOS boots press Ctrl+S or F4 when prompted to
enter the RAID BIOS.
UGT-ST310R
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select Delete RAID Set, then press Enter.
3. Select the RAID set then press Enter.
4. When asked Are You Sure(Y/N)?, press Y to confirm.
Resolving Conflicts
When a RAID set is created, then metadata written to the disk
includes drive connection information. If, after a disk failure, the
replacement disk was previously part of a RAID set (or used in
another system), it may have conflicting metadata. If so, this will
prohibit the RAID set from being either created or rebuilt, in
order for the RAID set to function properly, this old metadata
must be first overwritten with the new metadata. To resolve this,
from the main BIOS window select Resolve Conflicts, then
press Enter, the correct metadata, including the correct drive
connection information, will be written to the replacement disk.
Low Level Format
Low Level Format is build into the RAID BIOS to make it more
convenient to erase the entire contents of a hard disk drive,
including data, drive and partition information. The Low Level
Format utility works on single hard drive only, before the RAID
set is configured.
Logical Drive Info
This menu item allows the display of the assignment of physical
drives within a logical set (RAID0, RAID1, etc.). This is display
only function.
UGT-ST310R
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
BIOS Configuration
The 6-Port SATA II 150 PCI Host Card w/RAID BIOS will appear
every time your system starts up. If the BIOS doesn’t show,
please try your controller in another PCI slot. During this (POST)
process, the BIOS will show up and indicate the devices
attached to it.
Driver Installation
For Windows® 2000
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents
of the “UGT-ST310R\2000_XP_2003_Vista\32bit” folder,
found on the driver CD, onto a blank floppy disk then
follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Windows® 2000 installation procedure.
3. At the Windows® 2000 Setup screen, press F6 to install the
RAID driver.
4. When prompted, press S to specify the location of the
driver.
5. Insert the floppy disk, then press Enter.
6. Select Silicon Image SiI 3114 SoftRAID 5 Controller for
Windows 2000, then press Enter.
7. Press Enter again to finish driver installation, then follow the
on-screen instructions to complete the Windows installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
UGT-ST310R
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
to Windows.
2. At Found New Hardware Wizard, click Next.
3. Select Search for a suitable driver for my device
(recommend) then click Next.
4. Insert the driver CD, check CD-ROM drives, uncheck the
other boxes, click Next, then click Next again.
5. If the Digital Signature Not Found message appears, click
Yes. Our driver has been thoroughly tested for stability and
compatibility.
6. Click Finish.
7. Repeat steps 2-6.
8. Restart Windows to complete the driver installation.
For Windows® XP/Server 2003
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents
of the “UGT-ST310R\2000_XP_2003_Vista\32bit” folder,
found on the driver CD, onto a blank floppy disk then
follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press F6 to install the RAID
driver.
4. When prompted, press S to specify the location of the
driver.
5. Insert the floppy disk, then press Enter.
6. Select Silicon Image SiI 3114 SoftRAID 5 Controller for
Windows XP/Server 2003, then press Enter.
7. Press Enter to finish driver installation, then follow the on-
screen instructions to complete the Windows installation.
UGT-ST310R
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. At the Found New Hardware Wizard, select No, not this
time, then click Next.
3. Insert the driver CD, select Install the software
automatically (Recommended), and click Next.
4. Click Finish.
5. Restart Windows to complete the driver installation.
For Windows® XP-x64/Server 2003-x64
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents
of the “UGT-ST310R\XP_2003_Vista\64bit” folder, found
on the driver CD, onto a blank floppy disk then follow the
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press F6 to install the RAID
driver.
4. When prompted, press S to specify the location of the
driver.
5. Insert the floppy disk, then press Enter.
6. Select Silicon Image SiI 3114 SoftRAID 5 Controller (64-
bit Extended), then press Enter.
7. Press Enter to finish driver installation, then follow the on-
screen instructions to complete the Windows installation.
For An Existing Installation
UGT-ST310R
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. At the Found New Hardware Wizard, select No, not this
time, then click Next.
3. Insert the driver CD, select Install the software
automatically (Recommended), and click Next.
4. Click Finish.
5. Restart Windows to complete the driver installation.
For Windows® Vista
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents
of the “UGT-ST310R\2000_XP_2003_Vista\32bit” folder,
found on the driver CD, onto a blank floppy disk then
follow the directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press Load Driver to install
the RAID driver.
4. Insert the floppy disk, please select Silicon Image SiI 3114
SoftRAID 5 Controller (A:\si3114r5.inf), then press Next.
(Change A:\ to match your floppy drive letter)
5. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. At Found New Hardware Wizard, select Locate and
install driver software (recommended).
UGT-ST310R
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Please insert driver CD, click Next.
4. Click Close to complete the installation.
For Windows® Vista-x64
For A New Installation
A new installation requires a floppy disk for the driver
installation. To make this floppy disk, copy the contents
of the “UGT-ST310R\XP_2003_Vista\64bit” folder, found
on the driver CD, onto a blank floppy disk then follow the
directions below.
1. Setup the RAID Array prior to Windows installation.
2. Follow Microsoft’s Windows installation procedure.
3. At the Windows Setup screen, press Load Driver to install
the RAID driver.
4. Insert the floppy disk, please select Silicon Image SiI 3114
SoftRAID 5 Controller (A:\si3114r5.inf), then press Next.
(Change A:\ to match your floppy drive letter)
5. Follow the on-screen instructions to complete the Windows
installation.
For An Existing Installation
1. Setup the RAID Array prior to driver installation and boot up
to Windows.
2. At Found New Hardware Wizard, select Locate and
install driver software (recommended).
3. Please insert the driver CD, click Next.
4. Click Close to complete the installation.
To Verify Windows® Installation
1. Right click My Computer and click Manage.
UGT-ST310R
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Select Device Manager.
3. Double click SCSI and RAID Controller (Storage
controllers), then double click Silicon Image SiI 3114
SoftRAID 5 Controller to display driver properties. A
message this device is working properly is displayed in the
dialog box, the driver has been correctly installed.
SATA RAID 5 Management Software
Installation
For Windows® 2000/XP/Server 2003/Vista
1. Please insert the driver CD into your CD-ROM Drive.
2. At the Windows desktop click Start, then Run.
3. Type D:\UGT-ST310R\2000_XP_2003_Vista\32bit\setup.msi, then
click OK. (Change D: to match your CD-ROM drive letter)
4. Follow the on-screen instructions to complete the
installation.
For Windows® XP-x64/Server 2003-x64/Vista-x64
1. Please insert the driver CD into your CD-ROM Drive.
2. At the Windows desktop click Start, then Run.
3. Type D:\UGT-ST310R\XP_2003_Vista\64bit\setup.msi, then
click OK. (Change D: to match your CD-ROM drive letter)
4. Follow the on-screen instructions to complete the
installation.
UGT-ST310R
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
|
