2-Port SuperSpeed USB 3.0
PCI-e Host Card
User’s Manual
Model: UGT-PC302
All brand names and trademarks are properties of their respective owners.
w w w . v a n t e c u s a . c o m
Download from Www.Somanuals.com. All Manuals Search And Download.
Ports
Model:
Ports:
UGT-PC302
2 x External USB 3.0 Ports (Backwards
Compatible with USB 2.0 & 1.1)
15-pin SATA Power Connector (Required)
67 x 120 x 20mm
Power:
Dimensions:
OS Support
Microsoft Windows ® XP/Vista/7
System Requirements
z
Windows® XP, Vista, & 7 32/64 bit
PCI Express Enabled Computer System w/ Available PCI
Express Slot
z
z
Available PCI-e slot
Package Contents
z
z
z
z
1 x 2-Port SuperSpeed USB 3.0 PCI-e Host Card
1 x User’s Manual
1 x Driver CD
1 x Low Profile Bracket
UGT-PC302
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Layout
Before installing the Vantec 2-Port SuperSpeed USB 3.0 PCI-e
Host Card, please see the photo below highlighting the available
USB 3.0 ports of the card.
Note: Make sure to connect a SATA power to P3 as
additional power is required to function.
Hardware Installation
1. Turn off and unplug the power cable from the back of the
UGT-PC302
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
computer as well as any other attached devices.
2. Remove the cover to access the internal hardware of the
computer (refer to the manufacture of the computer
system/case documentation for more details).
3. Locate a free PCI Express slot and remove the metal cover
plate on the rear of the computer case. (2-Port PCI-e
SuperSpeed USB 3.0 Host Card will fit and work with any
PCI Express slot whether it be a x1, x4, x8, x16 slot.
Performance may vary with each slot.)
4. When installing the 2-Port PCI-e SuperSpeed USB 3.0 Host
Card, make sure to fasten the bracket as documented in
your manufacture’s documentation.
5. Be sure to connect the SATA power connector from the
power supply to the card as it does require additional power
to function properly.
6. Place the case cover back onto the computer.
7. Reattach the power and other devices back to the computer.
Driver Installation
1. When you are booting up the computer for the first time with
the new hardware installed, Windows will display the 'Found
UGT-PC302
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
New Hardware Wizard'.
2. Cancel the automatic driver installation and run the
Setup.exe located on the Driver CD.
Note: Setup.exe can also be found and downloaded
3. Run installer setup.exe on Driver CD “X:\UGT-PC302\” to
have the latest driver for 32/64bit Windows. (where X is the
drive path for your CD-ROM drive)
4. When installation of the driver is complete, please reboot
the system as prompted to complete the driver installation.
Note: When drivers have been successfully installed,
you may check if installation was successful within the
Device Manager where “NEC Electronics USB 3.0
Host Controller” will be shown.
UGT-PC302
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
The 2-Port SuperSpeed USB 3.0 PCI-e Host Card comes with a
1 year limited warranty (90 day parts). If your unit becomes
defective
within
that
time
frame,
please
go
to
www.vantecusa.com for information on how to receive warranty
exchange or repair. Cosmetic defects and missing parts are not
covered under this warranty. Please check the contents of the
unit to make sure you received all parts. Also, check for any
cosmetic flaws. If any parts are missing or if there are cosmetic
defects, please contact the retailer from which you purchased the
unit immediately and ask for a replacement.
Vantec Thermal Technologies
43951 Boscell Rd. Fremont, CA 94538
tel: 510-668-0368 fax: 510-668-0367
UGT-PC302
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
|