Before using this telephone, please read the
Important safety instructions on page 22 of this
manual.
For support, shopping, and everything new at VTech, visit our website at
The ENERGY STAR® program (www.energystar.gov) recognizes and
encourages the use of products that save energy and help protect our
environment. We are proud to mark this product with the ENERGY STAR®
label indicating it meets the latest energy efficiency guidelines.
Compatible with
Hearing Aid T-Coil
Telephones identified with this logo have reduced noise and interference when
used with most T-coil equipped hearing aids and cochlear implants. The TIA-
1083 Compliant Logo is a trademark of the Telecommunications Industry
Association. Used under license.
T
TIA-1083
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting started
Parts checklist
Your telephone contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
A
BC
D
E
F
JKL
TUV
OPER
MNO
P
QRS
W
X
Y
Z
TONE
1. Handset
2. Telephone line cord
3. Telephone base
power adapter
4. Battery compartment
cover
5. Battery
6. Telephone base with
wall bracket
7. User’s manual
• To purchase replacement batteries or power adapters, visit our website
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Getting started
Telephone base installation
If you subscribe to high-speed Internet service (Digital Subscriber Line
- DSL) through your telephone lines, you must install a DSL filter between
the telephone base and the telephone wall jack to prevent noise and caller
ID problems caused by DSL interference. Please contact your DSL service
provider for more information about DSL filters.
Telephone
wall jack
Telephone base
power adapter
Electrical outlet
(not controlled by
a wall switch)
DSL filter (not included)
required if you have
DSL high-speed
Internet service
Telephone line cord
Telephone base
• Use only the power adapters supplied with this product. To order a
• The power adapters are intended to be correctly oriented in a vertical or
floor mount position.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Getting started
Battery installation and charging
Install the battery as shown below. The battery may have enough charge for
short calls and then completely charge and drain the battery two or three times
every three months afterwards. For best performance, charge the battery for at
least 16 hours before first use. When the battery power is low, LOW BATTERY
is displayed and flashes on the handset screen.
1. Insert the plug of the battery as indicated. Make sure it is plugged securely
and matches the color-coded label inside the battery compartment.
2. Place the battery with the label THIS SIDE UP facing up, and the wires
inside the battery compartment.
3. Align the battery compartment cover flat against the battery compartment,
then slide it upwards until it clicks into place.
4. Charge the handset by placing it in the telephone base. The handset charge
light is on when charging.
1
2
3
4
A
BC
D
E
F
MNO
JK
L
V
P
T
QRS
ONE
T
U
W
X
Y
Z
O
PER
• If the handset will not be used for a long period of time, remove the battery
to prevent possible leakage.
•
(800) 267-7377.
Wall bracket installation
Your telephone base comes with the wall bracket installed, ready for desktop
use. You may also mount your telephone onto a standard telephone wall plate.
Wall bracket installation:
To prepare the telephone base for wall mounting, you need to remove the
bracket if it is currently attached for desktop use. Press the tabs located on
the legs of the bracket to loosen, then lift the bracket up and away from the
telephone base.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Getting started
Wall bracket installation (continued)
Wall bracket installation:
1. First, insert the lower portion tabs of the wall bracket into the lower grooves
in the telephone base, then snap the upper portion tabs of the wall bracket
into place.
2. Mount the telephone base on the wall by positioning it so the mounting
studs fit into the holes on the telephone base and wall bracket. Slide the
telephone base down on the mounting studs until it locks into place.
3. To remove the bracket, press both upper portion tabs firmly and pull the
bracket downward until it releases from the grooves.
upper portion tabs
Wall bracket
AC 7.5V
lower
portion
tabs
Wall bracket in wall
lower groove
mount orientation
upper grooves
Desktop/tabletop bracket installation:
Your telephone comes ready for table use. If you have repositioned the bracket
for wall mounting and now want to return to table use, follow these steps:
1. Insert the lower portion tabs of the wall bracket into the upper grooves of the
telephone base.
2. Snap the upper portion tabs of the wall bracket into place.
3. To remove the wall bracket, press both upper portion tabs firmly inward and
pull the wall bracket upward until it is released from the grooves.
AC 7.5V
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Getting started
Handset layout
CHARGE light
/VOL+/
• On when the handset is
charging in the telephone
base.
• Press to display the directory
when the telephone is not in
use.
• Press and hold to adjust
the ringer volume when the
telephone is not in use.
/VOL-/CID
• When the telephone is not
in use, press to review the
call log.
• Press and hold to adjust
the ringer volume when the
telephone is not in use.
• During a call, press to
lower the listening volume.
A double beep sounds at
the lowest setting.
• During a call, press to increase
the listening volume. A double
beep will sound when the
highest setting is reached.
• Press to scroll up while
or
in programming mode
reviewing the redial list.
SELECT
• Press to store a programming
option or a directory entry.
• Press to scroll down while
in programming mode or
reviewing the redial list.
OFF
• Press to make or answer
a call.
• During a call, press to hang
up.
• During a call, press to
receive an incoming call
when you receive a call
waiting alert.
• While the handset is ringing,
press to silence the ringer.
• Press and hold for two
seconds when the telephone
is not in use to erase the
MISSED CALLS display.
• During programming, press to
exit without making changes.
A BC
JKL
D EF
MNO
TONE
*
• Press to switch to tone
dialing temporarily when
using the pulse service
(page 10).
P
QRS
TUV
OPER
W
X Y Z
#
•
TONE
Press repeatedly to display other
dialing options when reviewing
the call log (page 18)
CHAN/REMOVE
.
•
Switch to a clearer channel
while on a call.
• Press to use the CLR
VOICEMAIL feature from the
main menu.
• Press and hold to delete all
records in the call log when
the phone is not in use.
• When reviewing the call
press to
log or redial list,
delete the desired record.
REDIAL/PAUSE
• Press repeatedly to review the
redial list.
• While dialing or entering
numbers into the directory,
press to insert a dialing
pause.
PROG
• Press to enter programming
mode while the telephone is
not in use.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Getting started
Telephone base layout
IN USE light
• Flashes when there is an
incoming call.
• On when the handset is in use.
VOICEMAIL light
• Flashes when you have new
voicemail from your telephone
company.
FIND HANDSET
• Press to page the handset.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Telephone settings
Date and time
If you subscribe to caller ID service, the date and time is set automatically with
the next incoming call. If you do not have caller ID service, you can set the
date and time manually.
1. Press PROG when the handset is not in use.
2. Press or until DATE/TIME is displayed. Press SELECT
3. When the month is flashing, press or until the screen displays the
correct month and then press SELECT.
4. When the date is flashing, press or until the screen displays the correct
date and then press SELECT.
5. When the hour is flashing, press or until the screen displays the correct
hour and then press SELECT.
6. When the minute is flashing, press or until the screen displays the
correct minute and then press SELECT.
7. When AM or PM is flashing, press or to choose between AM or PM
and then press SELECT. You will hear a confirmation tone.
• When there is a power failure, the time may need to be reset.
Ringer
You can select from different ringers.
1. Press PROG when the handset is not in use.
2. Press or until the screen displays RINGER: and the current setting.
3. Press SELECT. The current setting flashes, and you will hear a sample of the
ringer.
4. Press or to select RINGER: 1, 2, 3, or 4. You will hear a sample of
each ring tone.
5. Press SELECT to confirm your selection. You will hear a confirmation
tone.
Ringer volume
You can change the ringer volume to a comfortable level or turn the ringer off.
1. Press PROG when the handset is not in use. Press or until the
screen displays RINGER VOL: and the current setting.
2. Press SELECT. The current setting flashes, and you will hear a
sample of the ringer volume.
3. Press or to select ringer volume from OFF, LOW or HI. You will
hear a sample of the selected volume level.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Telephone settings
Ringer volume (continued)
4. Press SELECT to confirm your selection. You will hear a confirmation tone.
-OR-
1. Press and hold or until the screen displays RINGER VOL: and the
current setting when the handset is not in use. The current setting flashes
and you will hear a sample of the ringer volume.
2. Press or to select ringer volume from OFF, LOW or HI. You will hear a
sample of the selected volume level.
3. Press SELECT to confirm your selection. You will hear a confirmation tone.
• If the ringer volume is set to OFF, RINGER OFF and
are displayed.
• Even if the ringer volume is set to OFF, the handset still rings when you
press FIND HANDSET.
Dial mode
If you have touch tone service, the telephone is ready for use as soon as the
battery is charged. If you have pulse (rotary) service, you need to change the
dial mode.
1. Press PROG when the handset is not in use.
2. Press or until the screen displays DIAL MODE: and the current setting.
3. Press SELECT. The current setting flashes.
4. Press
or to select TONE or PULSE
5. Press SELECT to confirm your selection and there is a confirmation tone.
Home area code
If you dial your local calls using only seven digits (area code not required), you
can program your home area code, following the steps below. By programming
your home area code, when you receive a call within your local area, the
telephone number is automatically stored without the area code in the call log.
1. Press PROG when the handset is not in use.
2. Press or until the screen displays HOME AREA CODE.
3. Press SELECT The stored area code is displayed with the first digit
flashing.
4. Use the dial key pad to enter the desired home area code.
5. Press SELECT to confirm. You will hear a confirmation tone.
• If your phone service provider requires you to dial the area code when
making a local call, or you want to cancel the home area code you have
already programmed, reprogram your home area code to 000.
• Press CHAN/REMOVE when in the home area code menu to delete the
stored home area code. ___ is then displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Telephone settings
Language
1. Press PROG when the handset is not in use.
2. Press or until LANGUAGE is displayed.
3. Press SELECT. The current setting flashes.
4. Press or until the screen displays the desired language (ENGLISH,
ESPANOL or FRANCAIS).
5. Press SELECT to confirm your selection. You will hear a confirmation tone.
Clear voicemail
If you subscribe to voicemail services provided by your telephone company,
NEW VOICEMAIL and
are displayed on the handset and the VOICEMAIL
light on the telephone base flashes when you have a new voicemail message.
To turn this indicator off:
1. Press PROG when the handset is not in use.
2. Press or until the screen displays CLR VOICEMAIL.
3. Press SELECT. The screen displays CLEAR? and YES flashes.
4. Press SELECT to confirm your selection. You will hear a confirmation tone.
• The clear voicemail feature only turns off the displays NEW VOICEMAIL
and
on the handset, and the VOICEMAIL light on the telephone base. It
does not delete your voicemail message(s).
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Telephone operation
Make calls
• Press
-OR-
and then use the dial pad keys to dial a number.
1. Enter the phone number first. You can press to backspace and press
CHAN/REMOVE to erase digits.
2. Press
to dial.
Answer calls
• Press any dial pad keys (except /VOL-/CID, /VOL+/ and OFF) to answer
an incoming call.
End calls
• Press OFF or put the handset back to the telephone base to end a call.
• The call timer is activated during a call to show call duration.
• The handset beeps if it is moved out of range while on a call.
Volume
• Press /VOL-/CID or /VOL+/ to adjust the listening volume during a
conversation.
Channel
• Press CHAN/REMOVE to switch to a clearer channel while on a call.
Call waiting
If you subscribe to call waiting service and you are on a call when a new
call comes in, you will hear a beep. The caller ID information is displayed if
you subscribe to combined caller ID with call waiting service from your local
telephone company.
• Press
incoming call.
• Press
on the handset to put the current call on hold and answer the
at anytime to alternate between calls.
Temporary tone dialing
If you have pulse (rotary) service, you can change from pulse to touch tone
dialing during a call by pressing TONE . This is useful if you need to send
*
touch tone signals to access telephone banking or long distance services.
Once you have initiated your call by dialing the phone number in pulse (rotary),
press TONE . Now, all subsequent key presses are sent as touch tone signals.
*
After you hang up, the phone returns to pulse (rotary) dialing for the next call.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Telephone operation
Redial
• The telephone stores the five most recently dialed telephone numbers in the
redial list. When the list is full, the oldest entry is deleted to make room for
the new entry.
• Press REDIAL/PAUSE, then press
,
or REDIAL/PAUSE repeatedly to
review the redial list. Press CHAN/REMOVE to delete the displayed number.
• Press
dialed.
, then press REDIAL/PAUSE to dial the last telephone number
-OR-
Press REDIAL/PAUSE, then press
,
or REDIAL/PAUSE repeatedly until
to dial the number.
the desired entry displays, then press
Find handset
• Press FIND HANDSET on the telephone base to locate the handset when
the telephone is not in use and the handset is not placed in the telephone
base. The handset rings and PAGING will be displayed on its screen.
**
**
• Press FIND HANDSET again or put the handset back
on the telephone base to stop the paging tone.
-OR-
Press OFF on the handset.
Directory
The directory can store up to 20 entries (including nine speed dial entries).
Each entry may consist of a number up to 24 digits and a name up to 14
characters.
Store a directory entry
1. Press PROG when the handset is not in use. The screen displays DIRECTORY.
2. Press SELECT. The screen displays ENTER NAME.
3. Use the dial pad keys to enter the name. See the Character chart on page 12.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a character.
4. When finished, press SELECT or PROG. The screen displays ENTER NUMBER.
5. Use the dial pad keys to enter the telephone number.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a digit.
• Press REDIAL/PAUSE to insert a dialing pause (P is displayed).
6. Press SELECT or PROG. The screen displays DISTINCT RING? and the
current setting.
7. Press or to choose Y (yes) if you wish to customize this entry or
choose N (no) for a normal ringer. If you choose Y, a is displayed with the
directory entry.
8. Press SELECT or PROG to confirm and you hear a confirmation tone.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Telephone operation
Character chart
Use the dial pad keys and the chart below to enter a name (up to 14
characters). An error tone sounds if you try to enter more than 14 characters.
Each press of a particular key causes the characters to be displayed in the
following order:
Characters by number of key presses
Dial key
1
1
2
3
4
5
6
1
2
3
4
5
6
7
8
9
0
*
A
D
G
J
B
E
H
K
N
Q
U
X
C
F
I
2
3
4
5
6
S
8
Z
L
M
P
T
O
R
V
Y
7
9
W
0
*
,
#
&
,
-
.
#
Review the directory
1. Press /VOL+/ when the handset is not in use. The screen displays
DIRECTORY.
2. Press or to scroll through the entries stored in the directory alphabetically.
-OR-
Press the dial pad key for the first letter of the name you want to search. If
necessary, scroll or to find the desired entry.
• When you reach the end of the list in the directory, END OF LIST is shown
on the screen and there is an error tone.
• If you press a dial pad key for alphabetical search while in the directory
and there are no entries starting with the letters of that key, NO DATA is
displayed on the screen.
Edit a directory entry
1. Press /VOL+/ when the handset is not in use. The screen displays
DIRECTORY.
2. Press or to scroll through the entries stored in the directory
alphabetically.
-OR-
Press the dial pad key for the first letter of the entry you want to edit. If
necessary, scroll or to find the desired entry.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Telephone operation
Edit a directory entry (continued)
3. When the screen displays the desired entry, press
SPEED EDIT DEL
8005959511
SELECT and EDIT flashes.
4. Press SELECT. The screen displays the name and
number. The cursor appears at the beginning of the
name.
•
•
•
Use the dial pad keys to edit the name.
Press to move the cursor to the left or to the right.
Press CHAN/REMOVE to erase a character.
5. Press SELECT to move on to the phone number.
•
•
•
•
Use the dial pad keys to edit the number.
Press to move the cursor to the left or to the right.
Press CHAN/REMOVE to erase a digit.
Press REDIAL/PAUSE to insert a dialing pause (P will be displayed).
6. Press SELECT. The screen displays DISTINCT RING? and the current
setting.
7. Press or to choose Y (yes) to customize this entry, or choose N (no)
for a normal ringer. If you choose Y, a will be displayed with the directory
entry.
8. Press SELECT to confirm and you will hear a confirmation tone.
Delete a directory entry
1. Press /VOL+/ when the handset is not in use. The screen displays
DIRECTORY.
2. Press or to scroll through the entries stored in the directory
alphabetically.
-OR-
Press the dial pad key for the first letter of the entry to delete. If necessary,
scroll or to find the desired entry.
3. When the screen displays the desired entry, press
SPEED EDIT DEL
8005959511
SELECT. Then press or until DEL (delete)
flashes.
4. Press SELECT. The screen displays
ERASE NO YES and the number. The current
choice flashes.
5. Press until YES flashes.
6. Press SELECT. You will hear a confirmation beep.
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Telephone operation
Copy a directory entry into speed dial
1. Press /VOL+/ when the handset is not in use. The screen displays
DIRECTORY.
2. Press or to scroll through the entries stored in the directory
alphabetically.
-OR-
Press the dial pad key for the first letter of the entry to copy. If necessary,
scroll or to find the desired entry.
3. When the screen displays the desired entry, press
SPEED EDIT DEL
8005959511
SELECT. Then press or until SPEED flashes.
4. Press SELECT. The screen displays ENTER 1-9.
5. Press a key (1-9) to copy this entry from the
directory to the speed dial memory and assign the
memory location. You will hear a confirmation beep. A memory location
number (01 through 09) will be displayed with this entry.
Dial a number from the directory
1. Press /VOL+/ when the handset is not in use. The screen displays
DIRECTORY.
2. Press or to scroll through the entries stored in the directory
alphabetically.
-OR-
Press the dial pad key for the first letter of the desired entry. If necessary,
scroll or to find the desired entry.
3. When the screen displays the desired entry, press
.
Speed dial
Your telephone can store up to nine telephone numbers with names (up to 14
characters and 24 digits in each location) in the speed dial memory locations
you assign in the handset.
Store a speed dial entry
1. Press PROG when the handset is not in use and then press or
until the
screen displays SPEED DIAL.
2. Press SELECT. The screen displays ENTER 1-9.
3. Press a key (1 through 9) to assign the speed dial location to store this
number. The screen displays ENTER NAME.
4. Use the dial pad keys to enter the name (see the Character chart on page
12) and then press SELECT or PROG.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a character.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Telephone operation
Store a speed dial entry (continued)
5. The screen displays ENTER NUMBER.
6. Use the dial pad keys to enter the telephone number, and then press
SELECT or PROG.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a digit.
• Press REDIAL/PAUSE to insert a dialing pause (P will be displayed).
7. The screen displays DISTINCT RING? and the current setting.
8. Press or
to choose Y (yes) to customize this entry, or choose N (no) for
a normal ringer. If you choose Y, a will be displayed with the entry.
9. Press SELECT or PROG to confirm. You will hear a confirmation tone.
• The entries stored in the speed dial memory will be numbered 01 through
09 and share the memory in the directory.
• Press OFF at any time to exit speed dial mode.
• If the location is not empty, the new entry will replace the old entry and the
old entry will be moved to a directory location.
Edit a speed dial entry
1. Press and hold the speed dial location key (1-9) of the desired entry when
the handset is not in use.
2. When the screen displays the entry to edit, press
SPEED EDIT DEL
8005959511
SELECT and EDIT flashes.
3. Press SELECT. The screen displays the name and
01
number. The cursor appears at the beginning of the
name. Use the dial pad keys to edit the name.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a character.
4. Press SELECT to move on to the phone number. Use the dial pad keys to
edit the number.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a digit.
• Press REDIAL/PAUSE to insert a dialing pause (P will be displayed).
5. Press SELECT. The screen displays DISTINCT RING? and the current setting.
6. Press or to choose Y (yes) to customize this entry, or choose N (no)
for a normal ringer. If you choose Y, a will be displayed with the directory
entry.
7. Press SELECT to confirm. You will hear a confirmation tone.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Telephone operation
Delete a speed dial entry
1. Press and hold the speed dial location key (1-9) of
SPEED EDIT DEL
8005959511
the desired entry when the handset is not in use.
2. When the screen displays the desired entry, press
SELECT. Then press or until DEL (delete)
flashes.
01
3. Press SELECT. The screen displays ERASE NO YES and the number. The
current choice flashes.
4. Press until YES flashes.
5. Press SELECT. You will hear a confirmation beep.
Dial a speed dial number
1. Press and hold a speed dial location key (1-9) of the desired entry when the
handset is not in use.
2. Press
to dial the displayed number.
Reassign speed dial locations
1. Press and hold the speed dial location key (1-9) of the desired entry when
the handset is not in use.
2. When the screen displays the desired entry, press
SPEED EDIT DEL
8005959511
SELECT. Press or until SPEED flashes.
3. Press SELECT. The screen displays ENTER 1-9.
01
4. Press a key (1-9) to reassign this entry into another
memory location. You will hear a confirmation beep.
About caller ID
The caller ID with call waiting feature in this telephone lets you see the name
and telephone number of the caller before answering the call, even when
already on a call. These features require services provided by your local
telephone company.
Contact your telephone company if:
•
you have both caller ID and call waiting, but as separate services (you may
need combined service),
• you have only caller ID service, or only call waiting service, or
• you do not subscribe to any caller ID or call waiting services but wish to try
these services.
You can use this telephone with regular caller ID service, and you can use its
other features without subscribing to either caller ID or combined caller ID with
call waiting service. There may be fees for these services, and these services
may not be available in all areas.
The caller ID features will work only if both you and the caller are in areas
offering caller ID service, and if both telephone companies use compatible
equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Telephone operation
Call log
Caller’s name
VTECH
Caller’s telephone
number
800-595-9511
NEW05
New call log indicator
and location in the
call log
6:10AM
08/17
Time of call
Date of call
If you subscribe to caller ID service, information about each caller will be
displayed after the first or second ring.
• The call log can store up to 45 entries.
• When the call log is full, the earliest entry will be deleted to make room for
new incoming call information.
• CID EMPTY will be displayed if there is no record in the call log.
• If you answer a call before the information appears on the screen, it will not
be stored in the call log.
• The time on the handset screen is automatically set and updated with
incoming caller ID information if you subscribe to this service.
• Due to regional service differences, the caller ID information may not be
available for every incoming call. In addition, the callers may intentionally
block their names and/or telephone numbers.
Review the call log
1. Press /VOL-/CID to view the call log.
2. Press or to scroll through the entries.
There will be an error tone at the end of the call log list and the screen will
display END OF LIST.
• If you have programmed a home area code (page 8), only the last seven
digits of the incoming phone numbers from that area code will be displayed
while reviewing the call log. Press # repeatedly to display all possible
dialing options.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Telephone operation
Make call log entries ready to dial
Although the call log entries received have 10 digits (the
area code plus the seven-digit number), in some areas,
you may dial only the seven digits, or a 1 plus the seven
digits, or a 1 plus the area code plus the seven digits.
You can change the number of digits that you dial from
or store in the call log.
800-595-9511
1-800-595-9511
595-9511
1-595-9511
While reviewing the call log, press # repeatedly to
display different dialing options for local and long
distance numbers before dialing or saving the
telephone number in the directory. See the example on
the right.
800-595-9511
1-800-595-9511
595-9511
You may also press 1 repeatedly to add or remove a
1 in front of the telephone number before dialing or
saving it in the directory. See the examples on the right.
1-595-9511
When the number displayed is in the correct format for
dialing, press
to call the number.
• If you have programmed a home area code (page
8), only the last seven digits of the incoming phone numbers from that area
code will be displayed while reviewing the call log. Press # repeatedly to
display all possible dialing options.
Dial a call log number
1. Press /VOL-/CID to enter the call log when the telephone is not in use.
2. Press or to select the desired entry, then press
.
-OR-
1. Press /VOL-/CID to enter the call log when the telephone is not in use.
2. Press or to select the desired entry.
3. Press SELECT, then DIAL flashes.
4. Press
or SELECT.
Save a call log entry to the directory
1. Press /VOL-/CID to enter the call log when the telephone is not in use.
2. Press or to select the desired entry. If you
wish to change how the number is saved, press #
800-595-9511
repeatedly until the desired option displays. See
NEW28
the Make call log entries ready to dial section on
page 18.
5:40PM
12/30
DIAL PROGRAM
3. Press SELECT, then press or until PROGRAM
800-595-9511
flashes.
NEW28
12/30
4. Press SELECT again.
5:40PM
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Telephone operation
Save a call log entry to the directory (continued)
5. Enter or edit the name if necessary. See the Character chart on page 12.
•
Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a character.
Press SELECT to move on to the phone number.
6. Edit the number if necessary.
• Press to move the cursor to the left or to the right.
• Press CHAN/REMOVE to erase a digit.
• Press REDIAL/PAUSE to insert a dialing pause (P will be displayed).
Press SELECT to continue.
7. Press or to choose Y (yes) to customize this
DISTINCT RING? N
entry, or choose N (no) for a normal ringer. If you
8005959511
choose Y, a will be displayed with the directory
entry.
8. Press SELECT to confirm. You will hear a
confirmation tone.
Delete from the call log
Delete an entry:
1. Press /VOL-/CID to enter the call log when the telephone is not in use.
2. Press or to select the entry to be deleted.
3. Press CHAN/REMOVE. You will hear a confirmation beep.
Delete all entries:
1. Press and hold CHAN/REMOVE when the telephone is not in use. The
screen displays ERASE ALL? N Y. The current choice flashes.
2. Press until Y (yes) flashes.
3. Press SELECT. You will hear a confirmation beep.
Call log display screen messages
Displays:
When:
The caller is blocking the name information.
PRIVATE NAME
The caller is blocking the telephone number
information.
PRIVATE NUMBER
PRIVATE CALLER
The caller is blocking the name and number
information.
This caller’s name is unavailable.
UNKNOWN NAME
This caller’s number is unavailable.
No call information is available about this caller.
UNKNOWN NUMBER
UNKNOWN CALLER
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Appendix
Handset display screen messages
Displays:
When:
The battery needs to be recharged.
LOW BATTERY
CID EMPTY
There are no call log entries.
The cordless handset is searching for the
telephone base.
CONNECTING...
There are no directory entries.
DIRECTORY EMPTY
MEMORY FULL
The directory is full.
There are unreviewed calls in the call log.
XX MISSED CALLS
There are new voicemail message(s) from
the local telephone company.
NEW VOICEMAIL
**PAGING**
The cordless handset locator has been
activated.
The handset is in use.
PHONE
There is an incoming call.
The handset ringer is turned off.
**RINGING**
RINGER OFF
The telephone base is searching for another
available channel.
SCANNING...
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Appendix
Battery
After the battery is fully charged for 16 hours, you can expect the following
performance:
Operation
Operating time
Five hours
Six days
While in use (talking)
While not in use (standby*)
*Handset is off the telephone base but not in use.
The battery needs charging when:
• A new battery is installed in the handset.
• The handset beeps when taken off the telephone base.
• LOW BATTERY is displayed and the battery icon on the handset screen is flashing.
CAUTION:
• Use only the battery(ies) provided or equivalent. To order a replacement, visit our
vtechcanada.com or call 1 (800) 267-7377.
• Do not dispose of the battery(ies) in a fire. Check with local waste management codes
for special disposal instructions.
• Do not open or mutilate the battery(ies).
• Exercise care in handling batteries in order not to create a short circuit with
conductive materials such as rings, bracelets, and keys. The battery and/or conductor
may overheat and cause burns.
• Charge the battery(ies) provided with or identified for use with this product only in
accordance with the instructions and limitations specified in this manual.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO
WATER OR ANY TYPE OF MOISTURE.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Appendix
Important safety instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire,
electric shock and injury, including the following:
1. Read, understand, and follow all warnings and instructions marked on the product and in this manual.
2. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth
for cleaning.
3. Do not use this product near water (for example, near a bathtub, kitchen sink, or swimming pool). Never spill
liquid of any kind on the product.
4. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
5. Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To
protect them from overheating, these openings must not be blocked by placing the product on a soft surface
such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This
product should not be placed in any area where proper ventilation is not provided.
6. This product should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supply in your home, consult your dealer or local power company.
7. Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.
8. Never push objects of any kind into this product through the slots in the telephone base or handset as they may
touch dangerous voltage points or create a short circuit that could result in a risk of fire or electric shock.
9. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.
Opening or removing parts of the telephone base or handset other than specified access doors may expose
you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is
subsequently used, or if the product exhibits a distinct change in performance.
10. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
11. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following
conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If the product has been exposed to rain or water, or if liquid has been spilled onto the product.
C. If the product does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operation instructions. Improper adjustment of other controls may result in damage
and often requires extensive work by an authorized technician to restore the product to normal operation.
D. If the product has been dropped and the telephone base and/or handset has been damaged.
13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock
from lightning.
14. Do not use the telephone to report a gas leak in the vicinity of the leak.
15. Only put the handset of your telephone next to your ear when it is in normal talk mode.
16. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not
designed to hold the plug in place if it is plugged into a ceiling or an under-the-table/cabinet outlet.
SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Appendix
Troubleshooting
If you have difficulty with your telephone, please try the suggestions below. For
in Canada, call 1 (800) 267-7377.
My telephone does not work at all
• Make sure the battery is installed and charged correctly (page 3). For optimum daily
performance, return the handset to the telephone base after use.
• Make sure the power adapter is securely plugged into an outlet not controlled by a
wall switch.
• Make sure the telephone line cord is plugged firmly into the telephone base and the
wall jack.
• Unplug the unit’s electrical power. Wait for approximately 15 seconds, then plug it
back in. Allow up to one minute for the handset and telephone base to synchronize.
• Charge the battery in the handset for at least 16 hours.
• Remove and re-insert the battery. If that still does not work, it may be necessary to
purchase a new battery.
• Disconnect the telephone base from the jack and plug in a working telephone. If this
telephone does not work, call the local telephone company.
LOW BATTERY is displayed on screen
• Place the handset in the telephone base for recharging.
• Remove and re-install the battery and use it normally until fully depleted, then
recharge the handset in the telephone base for 16 hours.
• If the above measures do not correct the problem, the battery may need to be
replaced.
The battery does not charge in the handset or the handset battery does not
accept charge
• Make sure the handset is placed in the telephone base correctly and the handset
CHARGE light on the handset is on.
• Remove the battery from the handset and then re-install it in the handset. Put the
handset back to the telephone base and charge for 16 hours.
• If the handset is in the telephone base but the handset CHARGE light is not on, see
The CHARGE light is off in this section.
• It may be necessary to purchase a new battery. Please see the Battery section of this
user’s manual (page 21).
• The telephone might be malfunctioning. Please see the Warranty section of this
user’s manual (page 29) for further instruction.
The CHARGE light is off
• Clean the charging contacts on the handset(s) and telephone base each month using
a pencil eraser or a dry non-abrasive fabric.
• Make sure the power adapter and telephone line cords are plugged in correctly and
securely.
• Unplug the power adapter. Wait for 15 seconds before plugging it back in. Allow up to
one minute for the handset and telephone base to reset.
• The telephone might be malfunctioning. Please see the Warranty section of this
user’s manual (page 29) for further instruction.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Appendix
Troubleshooting
The talk time and standby time of my handset is noticeably shorter than before
• Completely charge and drain the battery two or three times consecutively every three
months instead of returning the handset to the telephone base or charger after each
use. If the performance does not improve, please buy a new battery.
There is no dial tone
• First, try all the above suggestions.
• Move the handset closer to the telephone base. It might be out of range.
• The telephone line cord might be malfunctioning. Try installing a new telephone line
cord.
• Disconnect the telephone base from the telephone jack and connect a different
telephone. If there is no dial tone on the other telephone either, contact your local
telephone company.
My handset displays CONNECTING
• Move the handset closer to the telephone base. You might have moved out of range.
The telephone does not ring when there is an incoming call
• Make sure the ringer is on (page 7).
• Make sure the telephone line cord and power adapter are plugged in properly (page
2).
• The handset may be too far from the telephone base. Move it closer to the telephone
base.
• There may be too many extension telephones on the telephone line to allow all of
them to ring simultaneously. Try unplugging some of them.
• If the other telephones in your home are having the same problem, contact the local
telephone company (charges may apply).
• Other electronic products can cause interference to your cordless telephone. Try
installing your telephone as far away as possible from the following electronic
devices: wireless routers, radios, radio towers, pager towers, cellular telephones,
digital telephones, intercoms, room monitors, televisions, VCRs, personal computers,
kitchen appliances, and other cordless telephones.
• Test a working telephone at the telephone jack. If another telephone has the same
problem, contact your local telephone company (charges may apply).
• The telephone line cord might be malfunctioning. Try installing a new telephone line
cord.
• Remove and re-insert the battery and place the handset in the telephone base.
• Wait for the handset to synchronize with the telephone base. Allow up to one minute
for this to take place.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Appendix
Troubleshooting
I cannot dial out
• First, try all the above suggestions.
• Make sure there is a dial tone before dialing. It is normal if the handset takes a second
or two to synchronize with the telephone base before producing a dial tone. Wait an
extra second before dialing.
• Make sure the telephone is set to the correct dial type (pulse dial or tone dial) for the
service in your area. See Dial mode on page 8 to set the dial type.
• If the other telephones in your home are having the same problem, contact your local
telephone company (charges may apply).
• Eliminate any background noise. If you cannot eliminate the background noise, first try
muting the handset before dialing, or dialing from another room in your home with less
background noise.
There is noise or interference during a telephone conversation
My calls cut in and out when I am using the cordless handset
• The handset may be out of range. Move it closer to the telephone base.
• Appliances or other cordless telephones plugged into the same circuit as the
telephone base can cause interference. Try moving the appliance or telephone base
to another outlet.
• Other electronic products can cause interference to your cordless telephone. Try
installing your telephone as far away as possible from the following electronic
devices: wireless routers, radios, radio towers, pager towers, cellular telephones,
digital telephones, intercoms, room monitors, televisions, VCRs, personal computers,
kitchen appliances, and other cordless telephones.
• If your telephone is plugged in with a modem or a surge protector, plug the telephone
(or modem/surge protector) into a different location. If this doesn’t solve the problem,
re-locate your telephone or modem farther apart from each other, or use a different
surge protector.
• The layout of your home or office might be limiting the operating range. Try moving
the telephone base to another location, preferably a higher location for better
reception.
• Disconnect the telephone base from the telephone jack and plug in a corded
telephone. If calls are still not clear, contact the local telephone company (charges
may apply).
• If the other telephones in your home are having the same problem, contact the local
telephone company (charges may apply).
• If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through
your telephone lines, you must install a DSL filter between the telephone base and
the telephone wall jack to prevent noise and caller ID problems caused by DSL
interference. Please contact your DSL service provider for more information about
DSL filters.
I hear other calls when using the telephone
• Disconnect the telephone base from the telephone jack. Plug in a different telephone.
If there are still other calls, call your local telephone company.
• Press CHAN/REMOVE to switch to a clearer channel when on a call.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Appendix
Troubleshooting
I hear noise in the handset, and none of the keys or buttons work
• Make sure the telephone line cord is plugged in securely.
• Remove and re-insert the battery.
My caller ID features are not working properly
• Caller ID is a subscription service. You must subscribe to this service from your local
telephone company for this feature to work on your telephone.
• The caller may not be calling from an area which supports caller ID.
• Both you and the caller’s telephone companies must use equipment which are
compatible with caller ID service.
• If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through
your telephone lines, you must install a DSL filter between the telephone base and
the telephone wall jack to prevent noise and caller ID problems caused by DSL
interference. Please contact your DSL service provider for more information about
DSL filters.
The system does not receive caller ID, or the system does not display caller ID
during call waiting
• Make sure you subscribe to caller ID with call waiting features provided by the local
telephone company.
• The caller may not be calling from an area which supports caller ID.
• Both you and the caller’s telephone companies must use equipment compatible with
caller ID service.
• If you subscribe to high-speed Internet service (Digital Subscriber Line - DSL) through
your telephone lines, you must install a DSL filter between the telephone base and
the telephone wall jack to prevent noise and caller ID problems caused by DSL
interference. Please contact your DSL service provider for more information about
DSL filters.
Caller ID entries do not match the numbers I need to dial
• Although the call log entries you receive have 10 digits, (the area code plus the
seven-digit number,) in some areas, you may need to dial only seven digits, or a 1
plus the seven digits, or a 1 plus the area code plus the seven digits. You can change
the number of digits that you dial or store from the call log.
• While reviewing the call log, press # repeatedly to display these dialing options for
local and long distance numbers before dialing or saving the telephone number.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Appendix
Troubleshooting
My cordless handset beeps and is not performing normally
• Make sure the power cord is securely plugged into the telephone base. Plug the unit
into a different working electrical outlet not controlled by a wall switch.
• Move the handset closer to the telephone base. It may be out of range.
• Reset the telephone base by unplugging the unit’s electrical power. Wait for 15
seconds and plug it back in again. Allow up to one minute for the handset and the
telephone base to synchronize.
• Other electronic products can cause interference to your cordless telephone. Try
installing your telephone as far away from these electronic devices as possible:
wireless routers, radios, radio towers, pager towers, cellular telephones, intercoms,
room monitors, televisions, personal computers, kitchen appliances and other
cordless telephones.
Common cure for electronic equipment
• If the unit is not responding normally, try putting the handset in the telephone base. If
it does not respond, try the following (in the order listed):
• Disconnect the power to the telephone base.
• Disconnect the battery on the handset.
• Wait a few minutes before connecting the power to the telephone base.
• Re-install the battery and place the handset in the telephone base.
• Wait for the handset to synchronize with the telephone base. Allow up to one minute
for this to take place.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Appendix
Operating range
This cordless telephone operates with the maximum power allowed by the Federal Communications Commission (FCC).
Even so, this handset and telephone base can communicate over only a certain distance, which can vary with the
locations of the telephone base and handset, the weather, and the layout of your home or office.
When the handset is out of range, the handset will display CONNECTING...
If there is a call while the handset is out of range, it might not ring, or if it does ring, the call might not connect well when
you press
. Move closer to the telephone base, then press
to answer the call.
If the handset moves out of range during a telephone conversation, there might be interference.
To improve reception, move closer to the telephone base.
Maintenance
Your cordless telephone contains sophisticated electronic parts and must be treated with care.
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to
ship it.
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet
hands. Do not install the telephone base near a sink, bathtub or shower.
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, take
caution when using electrical appliances during storms.
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth
slightly dampened with water or a mild soap. Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you are wet or standing in the water. If the
telephone base should fall into the water, DO NOT RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD AND
TELEPHONE LINE CORD FROM THE WALL. Then pull the unit out by the unplugged cords.
About cordless telephones
•
Privacy: There is a possibility that the cordless telephone conversations could be intercepted by radio receiving
equipment within range of the cordless handset. You should not think of cordless telephone conversations as
being as private as those on corded telephones.
•
•
Electrical Power: The telephone base of this cordless telephone must be connected to a working electrical
outlet not be controlled by a wall switch.
Potential TV interference: To minimize or prevent interference from cordless telephones, do not place the
telephone base of the cordless telephone near or on top of a TV or VCR. Moving the cordless telephone farther
away from the TV or VCR will often reduce or eliminate the interference.
•
•
Rechargeable batteries: This product contains either nickel-cadmium or nickel-metal hydride rechargeable
batteries. Exercise care in handling batteries in order not to create a short circuit with conducting material such
as rings, bracelets, and keys. The battery or conductor may overheat and cause harm. Observe proper polarity
between the battery and the battery charger.
Nickel-cadmium rechargeable batteries: Dispose of these batteries in a safe manner. Do not burn or puncture
the battery.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Appendix
Warranty
What does this limited warranty cover?
The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”)
that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and
workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance
with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased
and used in the United States of America and Canada.
What will VTech do if the Product is not free from defects in materials and workmanship during the limited
warranty period (“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s
option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished
replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of
the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the
Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you
in working condition. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs
or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies
to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement
Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or
Product that has been damaged due to repair, alteration or modification by anyone other than an authorized
service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or
antenna systems; or
4. Product to the extent that the problem is caused by use with non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada,
or used for commercial or institutional purposes (including but not limited to Products used for rental purposes);
or
7. Product returned without a valid proof of purchase (see item 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside
the unit.
How do you get warranty service?
To obtain warranty service in the United States of America, please call 1 (800) 595-9511. In Canada, please call
1 (800) 267-7377. NOTE: Before calling for service, please review the user’s manual - a check of the Product’s
controls and features may save you a service call.
Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and
are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location.
VTech will return repaired or replaced Product under this limited warranty to you, transportation, delivery or handling
charges prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not
covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will
notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay
for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a
description of the malfunction or difficulty; and
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date
of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Appendix
Warranty
Other Limitations
This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or
oral communications related to this Product. VTech provides no other warranties for this Product. The warranty
exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties.
No one is authorized to make modifications to this limited warranty and you should not rely on any such modification.
State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state or province to province.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten
warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/
provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply
to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages
(including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the
cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/
provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales receipt as proof of
purchase
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Appendix
FCC, ACTA and IC regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. Privacy of communications may not be ensured when using this telephone.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be
safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested
and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user’s body other than the hands are maintained at a distance
of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the
supplied VTech belt clip.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on the back or bottom of this equipment contains, among other
things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone
company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with
applicable Part 68 rules and technical requirements adopted by ACTA. A compliant telephone cord and modular plug
is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An
RJ11 jack should normally be used for connecting to a single line and an RJ14 jack for two lines. See Installation
Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone
line and still have them ring when you are called. The REN for this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all
RENs should be five (5.0) or less. For more information, please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected
to your telephone line, ensure the connection of this equipment does not disable your alarm equipment. If you have
questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been
corrected. Repairs to this telephone equipment can only be made by the manufacturer or its authorized agents. For
repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your
telephone service. The telephone company is required to notify you before interrupting service. If advance notice is
not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the
telephone company is required to inform you of your right to file a complaint with the FCC. Your telephone company
may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this
product. The telephone company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police,
fire, medical) in these locations. If you do store or test emergency numbers, please:
Remain on the line and briefly explain the reason for the call before hanging up.
Perform such activities in off-peak hours, such as early morning or late evening.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Appendix
FCC, ACTA and IC regulations
Industry Canada
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference, including interference that may cause undesired operation.
The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical
specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum
number of devices allowed to be connected to a telephone interface. The termination on an interface may consist
of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not
exceed five.
This product meets the applicable Industry Canada technical specifications.
The RBRC® seal
The RBRC® seal on the nickel-cadmium battery indicates that VTech Communications,
Inc. is voluntarily participating in an industry program to collect and recycle these batteries
at the end of their useful lives, when taken out of service within the United States and
Canada.
The RBRC® program provides a convenient alternative to placing used nickel-cadmium
batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local
retailers participating in the RBRC® program or at authorized VTech product service
centers. Please call 1-800-8-BATTERYTM for information on Ni-Cd battery recycling and
disposal bans/restrictions in your area. VTech’s involvement in this program is part of its
commitment to protecting our environment and conserving natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Appendix
Technical specifications
Frequency control
Transmit frequency
Crystal controlled PLL synthesizer
Handset: 5857.20-5865.90 MHz
Telephone base: 912.75-917.10MHz
Channels
30
Nominal effective range
Maximum power allowed by FCC and IC.
Actual operating range may vary according to
environmental conditions at the time of use.
Size
Handset: 7.32in X 2.01in X 1.57in (186.0mm X
51.0mm X 40.0mm)
Telephone base: 4.33in X 5.34in X 3.78in (110.0mm
X 135.6mm X 96.0mm)
Weight
Handset: 5.14oz (145.6g) (including battery)
Telephone base: 5.26oz (149g)
Power requirements
Memory
Handset: 3.6V 400mAh Ni-Cd battery
Telephone base: 7.5V AC @ 200mA
Handset directory: 20 memory locations (9 speed
dial inclusive); up to 24 digits and
14 characters
Handset call log: 45 memory locations; up to 11
digits and 15 characters
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Appendix
Index
A
H
About caller ID 16
About cordless telephones 28
Answer calls 10
Handset display screen messages 20
Handset layout
5
Home area code
8
Appendix 20
I
B
Important safety instructions 22
Index 34
Battery 21
Battery installation and charging
3
L
C
Language
9
Call log 17
Call log display screen messages 19
Call waiting 10
Channel 10
M
Maintenance 28
Make call log entries ready to dial 18
Make calls 10
Character chart 12
Charging
3
Clear voicemail
Copy a directory entry into speed dial 14
9
O
Operating range 28
D
P
Date and time
7
Parts checklist
1
Delete a directory entry 13
Delete a speed dial entry 16
Delete from the call log 19
Dial a call log number 18
Dial a number from the directory 14
Dial a speed dial number 16
Dial mode
Directory 11
DSL filter
R
Reassign speed dial locations 16
Redial 11
Review the call log 17
Review the directory 12
Ringer
Ringer volume
8
7
7
2
S
E
Save a call log entry to the directory 18
Speed dial 14
Store a directory entry 11
Store a speed dial entry 14
Edit a directory entry 12
Edit a speed dial entry 15
End calls
10
F
FCC, ACTA and IC regulations 31
Find handset 11
G
Getting started
1
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Appendix
Index
T
Technical specifications 33
Telephone base installation
2
Telephone base layout
Telephone operation 10
Telephone settings
6
7
Temporary tone dialing 10
The RBRC® seal 32
Troubleshooting 23
V
Volume 10
W
Wall bracket installation
Warranty 29
3
Download from Www.Somanuals.com. All Manuals Search And Download.
35
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon
Distributed in Canada by VTech Technologies Canada, Ltd., Richmond, B.C.
Copyright ©2008 for VTECH TELECOMMUNICATIONS LTD.
Printed in China.
91-001433-070-100
Download from Www.Somanuals.com. All Manuals Search And Download.
User’s manual
w w w.v techphones.com
Models: CS5111/CS5113
Download from Www.Somanuals.com. All Manuals Search And Download.
|