User’s Manual
www vtechphones com
Models: ia5874/
ia5876/ia5877
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation - Remote Access 32
Connect with the Answering System 32
Voice Menu 32
Remote Access Commands 32
Batteries 34
Battery Care and Maintenance 34
Replacing the Handset Battery 34
ADDITIONAL INFORMATION 35
Troubleshooting 35
Maintenance 42
Warranty Statement 42
Important Safety Instructions 44
FCC, ACTA and IC Regulations 45
The RBRC® Seal 46
Technical Specifications 47
Index 48
2
TABLE OF CONTENTS
Download from Www.Somanuals.com. All Manuals Search And Download.
NEED HELP?
This book has all the feature operation and troubleshooting you need to install
and operate your new VTech phone Please take the time to review thoroughly
to ensure proper installation and the benefit of this VTech innovative and feature
rich product You can also visit our website at www vtechphones com for support,
shopping, and everything new at VTech
In Canada, please visit www vtechcanada com
VTech toll free ꢀ-800-595-95ꢀꢀ
In Canada dial ꢀ-800-267-7377
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Enhanced 5.8GHz Technology - Dual band transmission combines the best of 5 8GHz
and 900MHz technologies, providing enhanced performance over standard cordless
telephones
•
Important!
B e f o r e u s i n g
this telephone,
you must read
Important Safety
Instructions on
page 44
Charger Power
Adaptors (2)
Parts Check List:
ꢀ Base Unit
2 Handsets (3)
3 Charger Power Adaptors (2)
4 Chargers (2)
5 Telephone Line Cord
6 Desk/Wall Mount Bracket
7 Belt Clips (3)
8 Base Power Adaptor
9 Batteries (3)
Chargers (2)
Handsets (3)
Base Unit
ꢀ0 User’s Manual
To purchase replacement
batteries, visit us on the web at
www vtechphones com or call
VTech Communications, Inc at ꢀ-
800-595-95ꢀꢀ In Canada, contact
VTech Telecommunications
Canada Ltd at www vtechcanada
com or ꢀ-800-267-7377
Desk/Wall Mount Bracket
Belt Clips (3)
Telephone Line Cord
User’s Manual
Batteries (3)
Base Power Adaptor
4
GETTING STARTED
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Choose Location
Install Handset Battery
For maximum performance of your
cordless telephone system:
a) Remove battery
compartment cover
by pressing on the
indentation and
•
Use only the
provided VTech
b a t t e r y , o r
equivalent
ꢀ Choose a central location for
your base unit
2 Install your base unit and
extension handsets away from
electronic equipment, such as
personal computers, television
sets and microwave ovens
sliding downwards
3 In locations where there are
multiple cordless telephones,
separate base units as much as
possible
4 Install your telephone
equipment away from heat
sources and sunlight
b) Align the two holes in the plug with
the socket pins, then snap the plug
5 Avoid excessive moisture, dust
into place
or extreme cold
c) Place the battery in the compartment with
the wires tucked inside
ꢀ
2
d) Replace cover by sliding it up into place
e) Place the handset in its base when
not in use to ensure maximum daily
performance
GETTING STARTED
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Connect Power and Telephone Line Cords
•
Install the base unit
awayfromelectronic
equipment such
a s p e r s o n a l
computers,
Modular
Standard
telephone jack
electrical outlet
television sets or
microwave ovens
Avoid excessive
heat, cold, dust or
moisture
•
•
Connect the power
and telephone
line cords to the
underside of the
base as illustrated
Connect the power cord After
charging the battery for at least
ꢀ6 hours, connect the telephone
line cord
P l u g t h e A C
adapter into an
electrical outlet If
the battery has not
been previously
charged,
placethehandsetin
the base, and allow
it to charge for ꢀ6
hours(orovernight)
Connect
the telephone line
cord to the wall
jack
6
GETTING STARTED
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Wall Mounting
Your phone base unit is designed to mount on a standard telephone wall plate Wall mounting
is optional See position one below for instructions
Desk/Table Installation
To place your base unit on a desk or table, insert the desk/wall bracket as instructed below and shown
in position one or two, depending on your preference of how you’d like the base unit to be angled
�
�
Position One
To mount your phone on a wall, or to place it on a table or desk, refer to the diagrams illustrating
position one
•
First insert the lower portion of the bracket into the grooves in the base, then snap the upper portion
into place
•
Mount the base on the wall by positioning the base unit so the mounting studs will fit into the holes
on the base and wall mount bracket Slide the base unit down on the mounting studs until it locks
into place
Position Two
This position is an alternate way to install your phone on a table or desk Position two allows a different
viewing angle to your handset and base unit Refer to the position two diagrams above
•
•
Insert the upper portion of the bracket into the grooves in the base
Snap the lower portion into place
GETTING STARTED
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Charge the Handset Battery
Place the handset in the base or charger NEEDS CHARGING will appear on the handset Charge
the battery for at least 16 hours the first time.
•
•
If the phone will
not be used for a
long period of time,
remove the battery
to prevent possible
leakage
Set Language Mode
• Press PROG, then press or until LANGUAGE is displayed Press SELECT.
▲
▼
• The current setting blinks Press or until the screen displays the correct language (English,
▲
▼
Spanish or French)
If you have any
trouble installing
y o u r p h o n e ,
please refer to the
Troubleshooting
s e c t i o n n e a r
the end of this
manual
• Press SELECT to save your selection
Check for Dial Tone
After the batteries are charged, pick up the handset and press PHONE; you should hear a dial tone
If you do not, refer to the TROUBLESHOOTING section in the back of this user’s manual
Set the Dial Mode
If you have touch tone service, the phone is ready to use as soon as the battery is charged If you
have pulse (rotary) service, you’ll need to change the dial mode
• Press PROG.
• Press or or until the screen displays DIAL MODE: and the current setting
▲
▼
• Press SELECT. The current setting blinks
• Press or to select TONE or PULSE.
▲
▼
• Press SELECT to save
8
GETTING STARTED
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Set Handset Date and Time
If you subscribe to caller ID service, the date and time will be set automatically with the first incoming
call If you do not have caller ID service, you can set the date and time manually:
•
In the event of a
power outage, or if
yourphone’spower
cord is unplugged,
the time setting will
be lost
•
•
•
•
•
•
Press PROG, then press or until DATE/TIME is displayed Press SELECT.
The month is flashing. Press or until the screen displays the correct month Press SELECT
The day is flashing. Press or until the screen displays the correct day Press SELECT.
The hour is flashing. Press or until the screen displays the correct hour Press SELECT.
The minute is flashing. Press or until the screen displays the correct minute Press SELECT.
AM or PM is flashing. Press or to choose between AM or PM. Press SELECT
Handset Ringer Style/Battery Save
You can select from four different handset ringer styles, or turn the ringer off and extend the
battery life
ꢀ With the handset in idle (off) mode, press PROG
2 Press or until the screen displays RINGER: and current setting
3 Press SELECT The current setting blinks, and you will hear a sample of the ring
4 Press or to select RINGER: 1, 2, 3, 4 or OFF You will hear a sample of each ring tone
5 Press SELECT to choose the displayed ringer setting
GETTING STARTED
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
If you subscribe to DSL service:
If you hear noise during conversations and/or your caller ID features aren’t functioning properly, install
a noise filter to the telephone line between the base unit and the telephone line jack. Contact your DSL
provider to obtain a noise filter.
Noise filter (For
DSL users)
line cord
Telephone
To single telephone
jack (RJꢀꢀC)
Belt clip (optional)
To remove
To attach
ꢀ0 GETTING STARTED
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Operation
Handset Operation
•
While entering names or
numbers into memory,
press to delete last
character entered
/DIR
While on a call, press to
increase the volume A
double beep will sound
when you reach the
highest setting
While phone is not in
use, press to display
directory entries
While entering names or
numbers, press to add a
space
1. Make a Call
Press PHONE, then dial the
number
-OR-
Dial the number (use
to backspace and make
corrections), then press
PHONE to call
•
2 Flash/Call Waiting
During a call, press to receive
an incoming
•
•
call, if call waiting is
activated
6
3 Channel
Press CHAN to switch to a
clear channel while on a call
ꢀ,2
7 Select
8
7
4 Delete
Press to display menu, or
When viewing the call log,
press to delete the current
record displayed While
handset is in idle mode, press
and hold to delete all records
in the call log
to select highlighted item
from menu
8 Off
During a call, press to
hang up While using
menus, press to cancel an
operation, back up, or exit
the menu display
5
5 Answer a Call
Press any key to answer a
call (except OFF)
9 Redial/Pause
6
/CID and /DIR
Press to view redial
/CID
memory While entering
numbers, press and hold to
insert a dialing pause
3,4
9
•
•
While on a call, press to
decrease the volume A
double beep will sound
when you reach the lowest
setting
ꢀ0 Program
ꢀ0
With the handset in idle
(on-hook), press to enter
programming mode
While phone is not in use,
press to display caller ID
information
BASIC OPERATION ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Operation
Base Operation
11. CHARGE/IN USE
•
Flashes in unison with an incoming call’s ringing
•
Flashes slowly when the handset is in use, or the answering
system is answering a call
•
Glows steadily when the handset is charging
12. LOCATE HANDSET
Press to page the handset for up to 60 seconds Press again,
press OFF on handset or place handset in base to cancel the
page
ꢀ2
ꢀꢀ
Temporary Tone Dialing
If you have pulse (rotary) service, you can change from dial pulse to touch tone dialing during a call by
pressing * TONE This is useful if you need to send touch tone signals for access to telephone banking
or long distance services
ꢀ Dial the number
2 Press TONE. Buttons pressed after this send touch tone signals
*
3 After you hang up, the phone automatically returns to pulse service
Message Waiting
Your phone is designed to work with most local and regional telephone service provider’s voice
messaging systems to provide an alert on handset when new messages come in Voice messaging is
a subscription service, available through most service providers for a monthly fee Contact your local
telephone company for more information
ꢀ2 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Operation
When you have a message waiting, the handset will display:
•
•
Only one handset
can be on a call at a
time For example, if
HSꢀ is on a call and
HS2 or HS3 presses
the PHONE button,
CAN’T CONNECT
will display
If the HS2 or HS3
cannotbefound,HSꢀ
will generate a sad
tone and continue
thecallautomatically
Before HS2 or HS3
answers, HSꢀ can
press PHONE to
cancel the forward
function and continue
the external call
IfHS2orHS3doesn’t
respond within 30
seconds, HSꢀ will
start ringing until
PHONE is pressed
to pick up the
returned call If it is
not answered within
another 30 seconds,
the external call will
end automatically
MESSAGE WAITING
5/01 5:40PM
Clear Message Waiting Alert
If after you review your message(s) your message waiting alert does not go off, you may manually
turn it off by:
ꢀ Press PROG on the handset
2 Press
or until screen displays MESSAGE WAITING
3 Press SELECT, the screen display: CLEAR? YES
4 Press or to change from YES to NO
5 Press SELECT, you’ll hear a confirmation tone.
Call Transfer
•
An external call can be forwarded from one handset (HSꢀ) to any other system handset (HS2 or
HS3) by following these steps:
ꢀ While on a call, press SELECT on HSꢀ to forward the call to HS2
HSꢀ will show:
HS2 or HS3 will ring and show:
TRANSFERRED CALL
CALL TRANSFERRED
2 Press PHONE on HS2 or HS3 to answer the forwarded call HSꢀ will return to the idle mode
BASIC OPERATION ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Operation
Headset Jack
Operating Range
You can use this telephone handsfree
when you install any VTech 2 5 mm
headset, purchased separately
This cordless telephone operates within the maximum
power allowed by the Federal
•
To purchase
a
headset, visit us
on the web at www
vtechphones com
or call VTech Cus-
tomer Service at
ꢀ-800-595-95ꢀꢀ
In Canada, contact
VTechTelecommu-
nications Canada
Ltd at www vtech-
canada com or ꢀ-
800-267-7377
Communications Commission (FCC) Even so, this
handset and base can communicate over only a
certain distance - which can vary with the locations
of the base and handset, the weather, and the
construction of your home or office.
Plug the headset into the jack located
on the right side of the handset (under
the small rubber flap). Do not force the
connection, but make sure the plug fits
securely
If you receive a call while you are out of range, the
handset might not ring or if it does ring, the call might
not connect when you press PHONE. Move closer to
the base, then press PHONE to answer the call
If you move out of range during a phone conversation,
you might hear noise or interference To improve
reception, move closer to the base
If you move out of range without pressing OFF, your
phone will be left off the hook To hang up properly,
walk back into range, periodically pressing OFF.
ꢀ4 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Operation
Display Screen Messages
Screen Displays:
When:
There is a call coming in
** RINGING **
CONNECTING...
PHONE ON
The handset is waiting for dial tone
The handset is in use
The base is paging the handset
The battery needs to be recharged
** PAGING **
BATTERY LOW
The handset is changing to another of the
30 channels available
SCANNING...
ꢀ Displays when one handset is on a call
and the other handset presses PHONE
2 Displays when base power is off and
PHONE is pressed You’ll also hear a sad
tone
CAN’T CONNECT
3 Displays when an out-of-range dial fails to
connect
The handset ringer is turned off
RINGER OFF
Displays when you have been alerted by the
telephone company that you have received
new voice mail
MESSAGE WAITING
BASIC OPERATION ꢀ5
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Dialing
Your phone can store up to nine telephone numbers with names (up to ꢀ5 characters and 24 digits in
each location) in the speed dial memory locations you assign (numbered ꢀ through 9) in each handset
These numbers can be dialed with two button presses You can also store telephone numbers with
names alphabetically in the directory See Telephone Directory for instructions
•
The entries you
store in speed
dial memory will
be marked with
0ꢀ through 09 and
also display in the
directory
Store a Number/Name in Speed Dial
ꢀ Press PROG Then press or until the screen displays SPEED DIAL.
2 Press SELECT The screen displays ENTER 1-9
3 Press the key (ꢀ through 9) to assign the speed dial location this number will be stored The screen
•
•
Press OFF at any
time to exit speed
dial mode
displays ENTER NAME
4 Using the chart below, enter up to ꢀ5 characters for the name you’re storing Use
to backspace
When memory
is full the screen
displays MEMORY
FULL,anerrortone
sounds and you
cannot store a new
number until you
delete a record in
speed dial memory
o r t e l e p h o n e
directory
and make corrections; use
to advance and add a space
Presses
Dial Key Once
Twice 3 Times 4 Times 5 Times 6 Times
ꢀ
ꢀ
A
B
E
H
K
N
Q
U
X
C
F
I
2
3
4
5
6
S
8
Z
2
D
3
G
4
J
L
5
M
O
R
V
Y
6
P
7
9
7
T
8
W
9
0
0
*
*
&
‘
,
-
#
#
ꢀ6 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Dialing
5 After you enter the name, press SELECT or PROG. The screen displays ENTER NUMBER
6 Enter the telephone number Use
to enter a pause if necessary
— OR —
to backspace and make corrections Press REDIAL/PAUSE
•
If the location is
not empty, your
new entry will be
stored in place
of the old and
will delete the
formerentry Take
caution to not
save over entries
you do not wish to
delete from speed
dial memory
Press REDIAL/PAUSE to display the last number (up to 24 digits long) dialed from this phone
7 Press SELECT or PROG to store your entry The screen displays DISTINCT RING? and the
current setting
8 Press or
to choose Y (for yes) if you wish the phone to alert you to calls from this number by
assigning a distinctive ringer after the first ring. Choose N for a normal ringer
9 Press SELECT or PROG to confirm. If you chose Y in Step 8, a
will be displayed with the
entry
Edit a Number/Name Stored in Speed Dial
ꢀ Press and hold the speed dial location key (ꢀ-9) of the entry you wish to edit
2 When the screen displays the entry you want to edit, press SELECT Then press or until EDIT
flashes.
SPEED EDIT ERASE
8005959511
01
3 Press SELECT The screen displays the name and number The cursor appears at the end of the
name Use
number Use to backspace and make corrections Press SELECT to move on to edit the distinctive
ring setting Press or to choose Y (for yes) if you wish the phone to alert you to calls from this
,
and the dial pad keys to edit the name Press SELECT to move on to edit the
number by assigning a distinctive ringer after the first ring. Choose N for a normal ringer.
4 Press SELECT to save the edited information
BASIC OPERATION ꢀ7
Download from Www.Somanuals.com. All Manuals Search And Download.
Speed Dialing
Delete a Number/Name Stored in Speed Dial
ꢀ Press and hold the speed dial location key (ꢀ-9) of the entry you wish to delete
2 When the screen displays the entry you want to delete, press SELECT Then press or until
ERASE flashes.
SPEED EDIT ERASE
8005959511
01
3 Press SELECT The screen displays ERASE NO YES and the number The current choice
flashes.
4 Press
until YES flashes.
5 Press SELECT. You’ll hear a confirmation beep.
Dial a Speed Dial Number
ꢀ Press and hold the speed dial location key (ꢀ-9) of the entry you wish to dial
2 Press PHONE to dial the displayed memory number
Reassign Locations in Speed Dial
ꢀ Press and hold the speed dial location key (ꢀ-9) of the entry you wish to reassign
2 When the screen displays the entry you want to reassign, press SELECT Press
or
until
SPEED flashes.
SPEED EDIT ERASE
8005959511
01
3 Press SELECT The screen displays ENTER 1-9
4. Press the keys (1-9) to reassign this entry into another memory location. You’ll hear a confirmation
beep
ꢀ8 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Directory
Your phone can store 20 (including the nine speed dial entries) telephone numbers with names (up to
ꢀ5 characters for the name and 24 digits for the number in each location) in the handset
•
Press OFF at any
time to exit the
directory
Store a Number/Name in the Directory
ꢀ Press PROG The screen displays DIRECTORY
2 Press SELECT The screen displays ENTER NAME
• When the memory
isfullthescreenwill
display MEMORY
FULL, an error
tone sounds and
you will not be
able to store a
new number until
you delete a stored
number to make
room for another
entry
3 Using the chart in page ꢀ6, enter up to ꢀ5 characters for the name you’re storing with the number
Use
to backspace and make corrections; use
to advance and add a space
4. When you finish entering the name, press SELECT or PROG The screen displays ENTER
NUMBER
5 Enter the telephone number Use to backspace and make corrections Press REDIAL/PAUSE to
store a pause if necessary
— OR —
Press REDIAL/PAUSE to display the last number (up to 24 digits) dialed from this handset
6 Press SELECT or PROG The screen displays DISTINCT RING? and the current setting
7 Press or
to choose Y (yes) if you wish the phone to alert you to calls from this number by
changing to a distinctive ringer after the first ring. Choose N for a normal ringer
8 Press SELECT or PROG to confirm. If you chose Y in Step 7, a will be displayed with the directory
entry
Edit a Number/Name Stored in the Directory
ꢀ Press The screen displays DIRECTORY
2 Press
or to scroll alphabetically through entries stored in directory
— OR —
Press the dial pad key for the first letter of the entry you want to edit.
BASIC OPERATION ꢀ9
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Directory
3 When the screen displays the entry you want to edit, press SELECT Then press or until EDIT
flashes.
SPEED EDIT ERASE
8005959511
4 Press SELECT The screen displays the name and number The cursor appears at the end of the
name Use
,
and the dial pad keys to edit the name Press SELECT to confirm and move on to
edit the number Use to backspace and make corrections Press SELECT to confirm and move
to edit the distinctive ring setting
5 Press SELECT to save the edited information
Delete a Number/Name Stored in the Directory
ꢀ Press The screen displays DIRECTORY
2 Press
or to scroll alphabetically through entries stored in directory
— OR —
Press the dial pad key for the first letter of the entry you want to delete.
3 When the screen displays the entry you want to delete, press SELECT Then press
or
until
ERASE flashes.
SPEED EDIT ERASE
8005959511
4 Press SELECT The screen displays ERASE NO YES and the number The current choice
flashes.
5 Press until YES flashes.
20 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Telephone Directory
6 Press SELECT. You’ll hear a confirmation beep.
Move a Number/Name to the Speed Dial Memory
ꢀ Press The screen displays DIRECTORY
2 Press or to scroll alphabetically through entries stored in directory
— OR —
Press the dial pad key for the first letter of the entry you want to move.
3 When the screen displays the entry you want to move, press SELECT Then press
or
until
SPEED flashes.
SPEED EDIT ERASE
8005959511
4 Press SELECT The screen displays ENTER 1-9
5 Press the key (ꢀ-9) to move this entry from the normal directory to the speed dial memory and assign
the memory location. You’ll hear a confirmation beep. A memory location number (1 through 9) will
be displayed with this entry
Dial a Number from the Directory
ꢀ Press The screen displays DIRECTORY
2 Press or to scroll alphabetically through entries stored in directory
— OR —
Press the dial pad key for the first letter of the entry you want to dial.
3 When the screen displays the entry you want to dial, press PHONE
BASIC OPERATION 2ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Your phone has a caller ID (CID) with call waiting feature that works with service from your local
phone service provider Caller ID with call waiting lets you see who’s calling before you answer the
phone, even when you’re on another call
You may need to change your phone service to use this feature Contact your phone service
provider if:
•
You have both caller ID and call waiting, but as separate services (you may need combined
service)
•
•
You have only caller ID service, or only caller waiting service
You don’t subscribe to any caller ID or call waiting services
You can use this product with regular caller ID service, and you can use this product’s other features
without subscribing to either caller ID or combined caller ID with call waiting service
There are fees for caller ID services, and they may not be available in all areas
This product can provide information only if both you and the caller are in areas offering caller ID
service, and if both telephone companies use compatible equipment
22 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Caller’s telephone
number
•
If you answer
a call before
the information
appears on the
screen, it will
not be in the call
history
Caller’s name
This party has called
more than once.
VTech
L
*
Long distance
call
800-595-9511
Position of call
in call history
NEW
OLD
PM
5/01 5:40 28
•
•
Press OFF at any
time to exit call
history
Indicate whether the
record is new or old
Date of call
Time of call
Each handset’s
c a l l l o g i s
independent from
the other handset
For example,
when you delete
one or all call log
entries from one
handset, they will
not be deleted
from the other
handsets
About Call History (Caller ID)
Your phone can store up to 45 calls in its caller ID (CID) memory When the memory is full, the oldest
call will automatically be deleted to make room for new incoming call information
For each call that comes in, the screen displays the following information between the first and second
rings:
•
•
•
•
Your caller’s name (ꢀ5 letters are sent by your telephone company)
The caller’s area code and telephone number
The time and date of the call
The repeat tag (*) in the upper right corner, indicating the party has called more than once
Review Call History
ꢀ Press (CID) to view call history
2 Use and to scroll through records in call history
BASIC OPERATION 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
Delete Records from Call History
Delete a Specific Call:
ꢀ Locate the record you want to delete from call history
•
CallerIDnumbers
may appear with
an area code
that may not be
required for local
calls, or without
a ꢀ that may be
needed for long
distance calls
If the number
displayed is not
in the right format,
press#repeatedly
to see different
dialing options
You can choose
to dial with or
without the area
code, or with or
without the ꢀ
2 Press the DELETE key to delete. You’ll hear a confirmation beep.
Delete All Calls:
ꢀ With the handset in idle (off) mode, press and hold the DELETE key to delete The screen displays
ERASE ALL NO YES. The current choice flashes.
2 Press until YES flashes.
3 Press SELECT. You’ll hear a confirmation beep.
Dial a Displayed Number
ꢀ Locate the record in call history that you want to dial
2 Ifyouwishtochangehowthenumberisdialed, press# The
800-595-9511
5/01 5:40 PM
screen displays any alternate dialing sequences available
for this call (area code + number; ꢀ + area code + number;
number only; ꢀ+ number) See the side column for more
information on changing the dialing format
OLD 28
3 Press SELECT Press or until DIAL flashes.
DIAL PROGRAM
800-595-9511
5/01 5:40 PM
4 Press SELECT The number is automatically dialed
— OR —
OLD 28
When the number is correctly displayed for dialing, you
want to dial, press PHONE
Store a Call History Record in the Directory
ꢀ Locate the record in the call history you want to store in
the directory
24 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Caller ID
2 If you wish to change how the number is stored, press
# The screen displays any alternate dialing sequences
available for this call (area code + number; ꢀ + area
code+number;numberonly; ꢀ+number) Seethenote
in the side margin for more information on changing
the dialing sequence
800-595-9511
5/01 5:40 PM
•
CallerIDnumbers
may appear with
an area code
that may not be
required for local
calls, or without
a ꢀ that may be
needed for long
distance calls
If the number
displayed is not
in the right format,
press#repeatedly
to see different
dialing options
You can choose
to dial with or
without the area
code, or with or
without the ꢀ
OLD 28
DIAL PROGRAM
800-595-9511
5/01 5:40 PM
3 Press SELECT, then press or until PROGRAM
flashes.
OLD 28
4 Press SELECT three times The screen displays:
DISTINCT RING? N
800-595-9511
5 Press or to select Y or N for distinctive ringer
5/01 5:40 PM
OLD 28
6 Press SELECT. You’ll hear a confirmation beep. If
you choose Y in step 5, a will be displayed with the
directory entry
Display Screen Messages
Screen Displays:
When:
The other party is blocking name and/or number
information
PRIVATE
Yourphonecompanyisunabletoreceiveinformation
about this caller’s name and/or number
UNKNOWN
This caller has called you more than once
* (after name)
BASIC OPERATION 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation At the Base
Audible Indicators
Your phone telephone system gives you voice prompts for feature operations and voice confirmations
when you press a button or complete an operation
•
•
The time will be
set automatically
with incoming caller
ID data You can
however choose
to set the time
manually
Setting the clock
ꢀ Make sure the answering system is on
2 Press TIME/SET The system announces the clock setting, then announces: “To begin setting
the clock, press TIME/SET, then press CHANGE to change the setting or press TIME/SET to
continue.”
To advance the
minute or year by
increments of ꢀ0,
press and hold
CHANGE
3 Press TIME/SET The system announces the current day
4 Press CHANGE until the system announces the correct day, then press TIME/SET The system
announces the current hour
5 Press CHANGE until the system announces the correct hour, then press TIME/SET The system
announces the current minute
6 Press CHANGE until the system announces the correct minute, then press TIME/SET The system
announces the current year
7 Press CHANGE until the system announces the correct year, press TIME/SET The system
announces the current clock setting
About Announcements
•
•
•
•
You can record two different announcements — one for normal answeringandoneforwhenyou’ve
set the system to play the announcement only
Use normal answering when you want the system to record callers’ messages Use announce
only when you want to give information to callers without accepting messages
If you choose not to record an announcement, the system answers with a pre-recorded
announcement
The normal answering pre-recorded announcement says: “Hello. Please leave a message after
the tone.” The announce only pre-recorded announcement says: “We’re sorry, messages to this
number cannot be accepted.”
26 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation At the Base
•
By setting announce only to on or off, you decide which announcement your callers will hear when
the system answers a call (the system comes set for normal answering, with announce only turned
off). See Set announce only, located in the Feature Summary chart later in this section, to change
your announcement selection.
•
Announcements
less than three
s e c o n d s i n
length will not be
recorded.
Select a feature setting
Enter answering system
feature setup and
choose a feature to set..
...
Record outgoing
announcements,
and memos
Turn answering
system on or off
Review/change clock setting;
confirm feature settings
Record Your Announcement
ꢀ. Press MENU until you hear “Announcement. Press PLAY or press RECORD. To continue setup,
press MENU.”
2. Press REC/MEMO. After you hear “Record after the tone. Press STOP when you are done.” followed
by a beep, speak toward the base to record an announcement up to 90 seconds long.
3. Press PLAY/STOP. The system plays back your recorded message.
To review your announcement at any time:
ꢀ. Press MENU until you hear “Announcement. Press PLAY or press RECORD. To continue setup,
press MENU.”
2. Press PLAY/STOP, the system plays the current announcement.
To delete your announcement:
Press DELETE during announcement playback. The system will use the pre-recorded announcement
until you record a new one.
BASIC OPERATION 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation At the Base
Setting Up Your Answering System
You can set up one feature at a time, or you can set up the first feature and then move on to set up
the other features in sequence.
•
To advance the
remote access
code number by
increments of ten,
press and hold the
CHANGE key.
ꢀ. Make sure the answering system is on.
2. Press MENU until the system announces the feature you want to set. Refer to the Feature Summary
below for a description of the features and your choices.
3. Press CHANGE until the system announces the desired setting.
4. Press TIME/SET to confirm your selection.
5. Press MENU to move on to the next feature, or press PLAY/STOP to exit feature setup.
Feature Summary
Default settings indicated by * .
System Announces:
Description/Directions:
Set the remote access code you will use to
access features and functions of the answering
system from a touch tone phone. You can
select any two digit code, from ꢀ0 to 99.
“Remote access code. To change the setting press
CHANGE.”
ꢀ9*
When message alert is turned on, the base
beeps once every ꢀ0 seconds when new
messages have been received.
“Message alert. To change the setting press CHANGE.”
Off*
On
When you turn announce only on, callers
hear your announcement, but cannot leave
a message.
“Announcement only, record no messages. To
change the setting press CHANGE.”
On
Off*
28 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation At the Base
“Base ringer. To change the setting press CHANGE.” Turn the base ringer on or off.
On*
Off
•
You can exit
feature setup
at any time by
pressing a PLAY/
STOP.
“Number of rings. To change the setting press
CHANGE.”
2
Choose how many times the phone will
ring before the system answers a call.
4*
6
• If the system
has less than
30 seconds of
record time left,
the answering
system turns
off. The system
w i l l a n s w e r
after ꢀ0 rings
and announce
“Memory is full.
Enter remote
access code.”
and wait for the
caller to enter the
remote access
code.
Toll Saver
With toll saver active, the system answers
after two rings when you have new
messages and after four when you have
no new messages.
Listen to, Save & Delete Messages
The system automatically saves your messages until you delete them, and can store approximately ꢀ5
minutes of messages, memos, and announcements (up to a maximum of 99 messages). A message
or memo can be up to four minutes long.
The message window will flash to alert you to new, unplayed messages. If all messages have been
reviewed, the number displayed in the window will glow steadily. If the system contains both old and
new messages, it will play only the new messages first. After all new messages are played, press the
PLAY/STOP to hear all messages.
Before playing a message, the system announces the day and time it was received. While the message
plays, the message window displays the number of the message. After playing the last message in a
mailbox, the system announces “End of messages.” If the system has less than five minutes of recording
time left, it announces remaining time.
BASIC OPERATION 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation At the Base
Press to repeat a message;
hold to back up and play the
previous message.
Message Window
Delete Messages
Press to skip to the next
message; hold to speed
up playback.
•
To delete a message, press
DELETE while the message
is playing.
•
•
Press and hold DELETE to
delete all old messages.
Youcannotdeleteamessage
until it’s been reviewed;
deleted messages cannot
be recovered.
Play Messages
Press to play messages. Press
again to stop playback.
Call Screening/Intercept
ꢀ. Make sure the answering system is on, and set the message playback volume control above
level ꢀ so you can hear the caller’s message.
2. If you decide to answer the call, press PHONE on the handset.
Record a Memo
You can record a memo up to four minutes long, which is stored as an incoming message.
ꢀ. Press and release REC/MEMO.
2. The system announces “Record after the tone. Press STOP when you are done.” After the beep,
speak toward the microphone. The message window displays the length of your memo up to 99
seconds, if you record a memo longer than 99 seconds, 99 continues to flash until you finish.
3. To stop recording, press the PLAY/STOP again.
30 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation At the Base
Window Display:
When:
No messages.
0
Total number of messages, or message number during
message playback.
1-98
Memory is full, or total number of messages is 99.
0-99 <--> F
Duration of announcement or memo recording (maximum
length of announcement is 90 seconds).
1 to 99(counting)
Length of recording is more than 99 seconds.
99(flashing)
Indicates volume level selected when VOL- or VOL+
is pressed.
1-8 (on steady for one second)
Current remote access code while setting.
Announce only mode.
10 - 99
A
System is set to announce only mode and the memory
is full.
1-98 and A (alternating)
Display when any setting is changed from on or off.
Clock needs to be set.
ONor OFF(steady for one second)
CL <--> (normal display)
--(steady)
System is answering a call or is in remote operation.
System is in programming mode or initializing.
--(flashing)
BASIC OPERATION 3ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation - Remote Access
Connect with the Answering System
You can access many features of this system remotely from a touch tone phone.
ꢀ. Dial your telephone number.
2. When the system answers, enter your remote access code (preset to 19). The system beeps once
and then announces the number of new messages.
3. Enter a remote command (see Remote Access Commands).
4. To end remote access, simply hang up the phone.
Voice Menu
The system has voice prompts to help you with remote operation. Press * 5 to hear the menu while
remotely connected to the answering system.
Remote Access Commands
Function:
Command:
Play messages
Press 1 to play all messages. Press 2 to play new messages. If
there are no new messages, the system plays old messages.
Repeat a message
Skip a message
Press 4 while message is playing; press 4 4 to back up previous
message.
Press 6 while message is playing; each press advances to the
next message.
Stop
Press 5.
Press *5.
Hang up.
Help
Save messages
32 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Answering System Operation - Remote Access
Function:
Command:
Delete message
Press 3 while message is playing. Press 3 3 to delete all old
messages.
• If no key is
pressed within
ꢀ0 seconds of
entering remote
access, the voice
menu will be
announced. After
the voice menu
announcement,
if no key is
pressed within
2 0 s e c o n d s ,
t h e r e m o t e
access call will
automatically
Review announcement
Record announcement
Press #7; system plays announcement, then beeps.
Press *7; after beep, record announcement, press 5 to stop.
System plays back announcement.
Record memo
Turn system off
Press 8, speak after beep; press 5 when finished.
Press 0; the system announces, “Answering machine off.” Press
0 again to turn the system back on.
When system is off, it answers after ꢀ0 rings and announces,
Please enter your remote access code. Enter your remote access
code, then press 0 to turn the answering system on.
Turn system on
end.
• I f a c c e s s i n g
Review remote access code Press #9.
Press *9 to change remote access code, then enter desired
remote access code from ꢀ0-99.
from
a
touch
Change remote access code
tone telephone,
press #5 to stop
recording.
BASIC OPERATION 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Batteries
Battery Care and performance:
After your battery is fully charged, you can expect the following performance:
•
•
If you repeatedly
get a low battery
indicator,evenafter
chargingovernight,
the battery should
be replaced.
Operation
Operating time
While in use (talking)
up to 5 hours
up to 6 days
While not in use (standby*)
* Handset is off the base unit or charger but not in use.
To reduce the risk
of fire or injury to
personsordamage
to the telephone,
read and follow
these instructions
carefully: Charge
t h e b a t t e r y
provided with
or identified for
use with this
product only in
accordance with
the instructions
and limitations
specified in the
user’s manual.
•
The battery needs charging when:
— A new battery is installed in the handset.
— The phone beeps twice every five seconds.
— The screen displays BATTERY LOW and the low battery icon.
Place the handset in the base so the CHARGE light turns on. The battery is typically fully
•
•
charged in ꢀ6 hours.
You can keep the battery fully charged by returning the handset to the base after each use.
Replacing the Handset Battery
ꢀ. Remove the battery compartment cover on the handset by pressing on the indentation and sliding the
cover downward.
2. Lift out the old battery and disconnect.
3. Align the two holes in the new battery’s plug with the socket
pins, and snap the plug into place. Snap the battery in the
compartment, as described in Installation, on page 5.
4. Replace the cover by sliding it up into place.
5. The new battery must be charged before using the phone.
Place the handset in the base and allow it to charge for at
least 16 hours the first charge. The telephone might operate
before that, but for best performance, let the battery charge
fully.
34 BASIC OPERATION
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If you have difficulty operating your phone, the suggestions below should solve the problem. If you still have difficulty after
trying these suggestions, call VTech Communications at ꢀ-800-595-95ꢀꢀ. In Canada, call VTech Telecommunications
Canada Ltd. at ꢀ-800-267-7377.
Problem
Suggestion
My phone doesn’t
work at all.
• Make sure the power cord is plugged in.
• Make sure the telephone line cord is plugged firmly into the base unit and the telephone wall
jack.
• Charge the battery in the handset for ꢀ6 hours. For optimum daily performance, return the
handset to its base when not in use.
• Reset the base. Unplug the unit’s electrical power. Wait for ꢀ5 seconds then plug it back in.
Allow up to one minute for the handset and base to reset.
• You may need to purchase a new battery, please refer to the Batteries section of this
user’s manual.
I cannot get a dial
tone.
• First try all the suggestions above.
• Move the handset closer to the base. You might have moved out of range.
• Your line cord might be malfunctioning. Try installing a new line cord.
• If the previous suggestions don’t work, disconnect the base unit from the telephone jack and
connect a different phone. If there is no dial tone on that phone either, the problem is in your
wiring or local service. Contact your local telephone company.
ADDITIONAL INFO
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Suggestion
I cannot dial out.
• Make sure you have a dial tone before dialing. The handset may take a second or two to find
the base and produce a dial tone. This is normal. Wait an extra second before dialing.
• Make sure your phone is set to the correct dial mode for the type of service that you have
(pulse or touchtone). Refer to the Installation section of this user’s manual to set the dial mode.
• If the other phones in your home are having the issue, the problem is in your wiring or local
service. Contact your local telephone company (charges may apply.)
• Eliminate any background noise. Noise from a television, radio or other appliance may cause
the phone to not dial out properly. If you cannot eliminate the background noise, first try muting
the handset before dialing, or dialing from another room in your home with less background
noise.
My handset beeps
five times and isn’t
performing normally.
• Make sure the power cord is securely plugged into the base. Plug the unit into a different,
working outlet not controlled by a wall switch.
• Move the handset closer to the base. You might have moved out of range.
• If the handset is in its base and the charging light does not come on, refer to Charge Light is
Off in this troubleshooting guide.
• Reset the base. Unplug the unit’s electrical power. Wait for ꢀ5 seconds then plug it back in.
Allow up to one minute for the handset and base to reset.
• Other electronic products can cause interference with your cordless phone. Try installing your
phone as far away from these types of electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones.
36 ADDITIONAL INFO
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Suggestion
•
Only one handset of your phone system can be in use (off hook) at a time. For example, if HSꢀ
is on a call and HS2 presses the PHONE button, CAN’T CONNECT will display. Be sure only
one handset is in use at a time.
CAN’T CONNECT
displays on my
handset.
•
•
Move the handset closer to the base. You might have moved out of range.
If the handset is in its base and the charging light does not come on, refer to The charge light
is off in this troubleshooting guide.
•
•
Reset the base. Unplug the unit’s electrical power. Wait for ꢀ5 seconds then plug it back in. Allow
up to one minute for the handset and base to reset.
Other electronic products can cause interference with your cordless phone. Try installing your
phone as far away from these types of electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones.
The batteries will not
hold a charge.
•
•
•
Charge the battery in the handset for ꢀ6 hours. For optimum daily performance, return the
handset to its base when not in use.
You may need to purchase a new battery, please refer to the Batteries section of this user’s
manual.
Your phone might be malfunctioning. Please refer to the Warranty section of this user’s manual
for further instruction.
If you subscribe to DSL If you hear noise during conversations and/or your caller ID features aren’t functioning properly,
service
install a noise filter to the telephone line between the base unit and the telephone line jack. Contact
your DSL provider to obtain a noise filter.
ADDITIONAL INFO
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Suggestion
I get noise, static,
or weak signal even
when I’m near the
base.
•
•
Press the CHAN button while on a call until the interference has been eliminated.
Other electronic products can cause interference with your cordless phone. Try installing your
phone as far away from these types of electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones.
•
•
Microwaves operate on the same frequency as your phone. It is normal to experience static on
your phone while the microwave is running. Do not install this phone in the same outlet or near
the microwave.
If your phone is plugged in with a modem or surge protector, plug the phone (or modem/surge
protector) into a different location. If this solves the problem, re-locate your phone or modem
farther apart from one another, or use a different surge protector.
•
•
Relocate your phone to a higher location. The phone will likely get better reception not installed
in a low area.
If the other phones in your home are having the issue, the problem is in your wiring or local
service. Contact your local telephone company (charges may apply.)
I hear other calls while
using my phone.
•
•
Disconnect your base unit from the telephone jack, and plug in a regular telephone. If you
still hear other calls, the problem is probably in your wiring or local service. Call your local
telephone company.
I hear noise in the
handset, and none of
the keys or buttons
work.
Make sure the power cord is plugged in.
38 ADDITIONAL INFO
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Suggestion
My handset does not
ring when I receive
a call.
•
Make sure you have the ringer activated. Refer to the section(s) on ringer selection in this user’s
manual.
Make sure the telephone line cord is plugged firmly into the base unit and the telephone jack.
Make sure the power cord is plugged in.
•
•
•
You may be too far from the base unit.
Charge the battery in the handset for ꢀ6 hours. For optimum daily performance, return the
handset to its base when not in use.
•
•
•
•
•
You may have too many extension phones on your telephone line to allow all of them to ring.
Try unplugging some of the other phones.
The layout of your home or office might be limiting the operating range. Try moving the base to
another location, preferably on an upper floor.
If the other phones in your home are having the issue, the problem is in your wiring or local
service. Contact your local telephone company (charges may apply.)
Test a working phone at the phone jack. If another phone has the same problem, the problem
is the phone jack. Contact your local telephone company (charges may apply.)
Other electronic products can cause interference with your cordless phone. Try installing your
phone as far away from these types of electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones
•
Your line cord might be malfunctioning. Try installing a new line cord.
ADDITIONAL INFO
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Suggestion
My calls fade or cut in
and out while I’m using
my handset.
•
•
Press the CHAN button while on a call until the interference has been eliminated.
Other electronic products can cause interference with your cordless phone. Try installing your
phone as far away from these types of electronic devices as possible: wireless routers, radios,
radio towers, pager towers, cell phones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and other cordless phones
•
•
Microwaves operate on the same frequency as your phone. It is normal to experience static on
your phone while the microwave is running. Do not install this phone in the same outlet or near
the microwave.
If your phone is plugged in with a modem or surge protector, plug the phone (or modem/surge
protector) into a different location. If this solves the problem, re-locate your phone or modem
farther apart from one another, or use a different surge protector.
•
•
Relocate your phone to a higher location. The phone will get better reception not installed in a
low area.
If the other phones in your home are having the issue, the problem is in your wiring or local
service. Contact your local telephone company (charges may apply.)
The charge light is off.
•
•
•
Clean the handset and base charging contact each month using a pencil eraser or cloth.
Make sure the power and line cords are plugged in correctly and firmly.
Reset the base. Unplug the unit’s electrical power. Wait for ꢀ5 seconds then plug it back in. Allow
up to one minute for the handset and base to reset.
•
Your phone might be malfunctioning. Please refer to the Warranty section of this user’s manual
for further instruction.
40 ADDITIONAL INFO
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Suggestion
My Caller ID isn’t
working.
•
Caller ID is a subscription service. You must subscribe to this service for this feature to work on
your phone.
•
•
Your caller must be calling from an area that supports caller ID.
Both you and your caller’s telephone companies must use caller ID compatible equipment.
My answering machine
is not recording
messages.
•
•
Make sure system is turned ON (the ON/OFF key is illuminated).
Make sure the announce only feature is set to OFF.
I cannot hear recorded
messages.
•
Using the base volume control, raise the volume to a comfortable listening level.
CL is flashing in the
base message display
window.
•
•
You need to set the day and time. Refer to the section(s) on setting day and time in this
user’s manual.
Make sure announce only feature is set to OFF
Common cure for
electronic equipment.
If the unit does not seem to be responding normally, then try putting the handset in its base. If it
does not seem to respond, do the following (in the order listed):
ꢀ. Disconnect the power to the base.
2. Disconnect the handset battery, and spare battery, if applicable.
3. Wait a few minutes.
4. Connect power to the base.
5. Re-install the battery(ies).
6. Wait for the handset to re-establish its link with the base. To be safe, allow up to one minute for
this to take place.
ADDITIONAL INFO
4ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Taking care of your telephone
Your cordless telephone contains sophisticated electronic parts, so it must be treated with care.
Avoid rough treatment
Place the handset down gently. Save the original packing materials to protect your telephone if you ever need to ship it.
Avoid water
Your telephone can be damaged if it gets wet. Do not use the handset outdoors in the rain, or handle it with wet hands. Do not install your base unit near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic equipment. For your own safety, use caution when using electric appliances during storms.
Cleaning your telephone
Your telephone has a durable plastic casing that should retain its luster for many years. Clean it only with a soft cloth slightly dampened with water or a mild soap. Do not use excess water or cleaning
solvents of any kind.
Warranty Statement
Remember that electrical appliances can cause serious injury if used when you are wet or standing in water. If your base unit should fall into water, DO NOT RETRIEVE IT UNTIL YOU
UNPLUG THE POWER CORD AND TELEPHONE LINE CORDS FROM THE WALL. Then pull the unit out by the unplugged cords.
What does this limited warranty cover?
• The manufacturer of this VTech product, VTech Communications, warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the product and all accessories provided
by VTech in the sales package (“Product”) are free from material defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally
and in accordance with operation instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America.
What will VTech Communications do if the Product is not free from material defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?
• During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair this
product, we may use new or refurbished replacement parts. If we choose to replace this product, we may replace it with a new or refurbished product of the same or similar design. VTech
will return repaired or replacement products to you in working condition. VTech will retain defective parts, modules, or equipment. Repair or replacement of Product, at VTech’s option, is
your exclusive remedy. You should expect the repair or replacement to take approximately 30 days.
How long is the limited warranty period?
• The limited warranty period for the product extends for ONE (ꢀ) YEAR from the date of purchase if we repair or replace a Materially Defective Product under the terms of this limited
warranty. This limited warranty also applies to repaired or replacement Products for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or
(b) the time remaining on the original one-year warranty; whichever is longer.
What is not covered by this limited warranty?
This limited warranty does not cover
1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other
liquid intrusion; or
2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or
3. Product to the extent that the problem experienced is caused by signal conditions, network reliability or cable or antenna systems; or
42 ADDITIONAL INFO
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty Statement
4. Product to the extent that the problem is caused by use with non-VTech electrical accessories; or
5. Product whose warranty/quality stickers, Product serial numbers plates or electronic serial numbers have been removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair from outside the United States, or used for commercial or institutional purposes (including but not limited to Products used for
rental purposes ); or
7. Product returned without valid proof of purchase (see 2 below); or
8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.
How do you get warranty service?
• To obtain warranty service in the United States of America, call ꢀ-800-595-95ꢀꢀ for instructions regarding where to return the Product. Before calling for service, please check the user’s
manual. A check of the Product controls and features may save you a service call.
• Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the
transport of Product (s) to the service location. VTech will return repaired or replaced product under this limited warranty to you, transportation, delivery or handling charges prepaid.
VTech assumes no risk for damage or loss of the Product in transit.
• If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize
the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty;
2. Include “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and
3. Provide your name, complete and correct mailing address, and telephone number.
Other Limitations
• This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other
warranties for this product. The warranty exclusively describes all of VTech’s responsibilities regarding the product. There are no other express warranties. No one is authorized to make
modifications to this limited warranty and you should not rely on any such modification.
State Law Rights: This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the product is fit for ordinary use) are limited to one year
from date of purchase. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
• In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the product, or
other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or exclusion may not apply to you.
ADDITIONAL INFO
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:
ꢀ.
2.
3.
4.
5.
6.
Read and understand all instructions.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool).
Do not place this product on an unstable surface, such as a table, shelf or stand. The product may fall, causing serious damage.
Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the
product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper
ventilation is not provided.
7.
This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power
company.
8.
Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it.
Never push objects of any kind into this product through slots in the base or handset as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric
shock. Never spill liquid of any kind on the product.
9.
10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the base or handset other than specified access
doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
ꢀ2. Unplug this product from the wall outlet and refer servicing to an authorized service facility under the
following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of
other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.
E. If the product has been dropped and the base and/or handset has been damaged.
F. If the product exhibits a distinct change in performance.
ꢀ3.
Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.
ꢀ4.
ꢀ5.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Only put the handset of your telephone next to your ear when it is in normal talk.
44 ADDITIONAL INFO
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC, ACTA and IC Regulations
FCC Part 15
This equipment has been tested and found to comply with the requirements for a Class B digital device under Part ꢀ5 of the Federal Communications Commission (FCC) rules. These requirements are
intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product.
This product has been tested and found to comply with the FCC criteria. The handset may be safely held against the ear of the user. The base unit shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of approximately 20 cm (8 inches) or more. If you choose to use a clipping device, please make sure to only use the supplied VTech belt clip.
FCC Part 68 and ACTA
This equipment complies with Part 68 of the FCC rules and with technical requirements adopted by the Administrative Council for Terminal Attachments (ACTA). The label on the back or bottom of this
equipment contains, among other things, a product identifier in the format US:AAAEQ##TXXXX. This identifier must be provided to your local telephone company upon request.
The plug and jack used to connect this equipment to premises wiring and the telephone network must comply with applicable Part 68 rules and technical requirements adopted by ACTA. A compliant
telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. An RJꢀꢀ jack should normally be used for connecting
to a single line and an RJꢀ4 jack for two lines. See Installation Instructions in the user’s manual.
The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line and still have them ring when you are called. The REN for this product is encoded
as the 6th and 7th characters following the US: in the product identifier (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the sum of all RENs should be five (5.0) or less. For more information,
please contact your local telephone company.
This equipment may not be used with Party Lines. If you have specially wired alarm dialing equipment connected to your telephone line, ensure the connection of this equipment does not disable your
alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
If this equipment is malfunctioning, it must be unplugged from the modular jack until the problem has been corrected. Repairs to this telephone equipment can only be made by the manufacturer or its
authorized agents. For repair procedures, follow the instructions outlined under the Limited Warranty.
If this equipment is causing harm to the telephone network, the telephone company may temporarily discontinue your telephone service. The telephone company is required to notify you before interrupting
service. If advance notice is not practical, you will be notified as soon as possible. You will be given the opportunity to correct the problem and the telephone company is required to inform you of your right
to file a complaint with the FCC. Your telephone company may make changes in its facilities, equipment, operation, or procedures that could affect the proper functioning of this product. The telephone
company is required to notify you if such changes are planned.
If this product is equipped with a corded or cordless handset, it is hearing aid compatible.
If this product has memory dialing locations, you may choose to store emergency telephone numbers (e.g., police, fire, medical) in these locations. If you do store or test emergency numbers, please:
ADDITIONAL INFO
45
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC, ACTA and IC Regulations
* Remain on the line and briefly explain the reason for the call before hanging up.
* Perform such activities in off-peak hours, such as early morning or late evening.
Industry Canada
This equipment complies with regulations RSS2ꢀ0 and CS-03 of Industry Canada. Operation is subject to the following two conditions: (ꢀ) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired operation of the device.
The term ‘’IC: ‘’ before the certification/registration number only signifies that the Industry Canada technical specifications were met.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.ꢀ. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination
on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.
The RBRC® Seal
The RBRC® Seal on the nickel-cadmium battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the
end of their useful lives, when taken out of service within the United States and Canada.
The RBRC® program provides a convenient alternative to placing used nickel-cadmium batteries into the trash or municipal waste, which may be illegal in your area.
VTech’s participation in RBRC® makes it easy for you to drop off the spent battery at local retailers participating in the RBRC® program or at authorized VTech product service centers. Please call
ꢀ-800-8-BATTERY™ for information on Ni-Cd battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment
and conserving natural resources.
RBRC® is a registered trademark of Rechargeable Battery Recycling Corporation.
46 ADDITIONAL INFO
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Enhanced 5.8GHz technology–your phone operates on a dual band transmission that combines the best of 5.8GHz and
900MHz technologies, providing enhanced performance over standard cordless telephones.
Frequency Control
Crystal controlled
PLL synthesizer
Transmit Frequency
Receive Frequency
Base: 9ꢀ2.75 - 9ꢀ7.ꢀ0 MHz
Handset: 5863.80 - 5872.5 MHz
Base: 5863.80 - 5872.5 MHz
Handset: 9ꢀ2.75 - 9ꢀ7.ꢀ0 MHz
Channels
30
Maximum power allowed by FCC and IC. Actual operating range may
vary according to environmental conditions at the time of use.
Nominal Effective Range
Size
Handset: ꢀ84mm X 52mm X 4ꢀmm
Base: ꢀ60mm X ꢀ44mm X ꢀ04mm (with wall mount)
Charger: 85mm X 78mm X 50mm
Weight
Handset: ꢀ30 grams
Charger: 6ꢀgrams
Base: 347 grams (with wall mount)
Power Requirements
Handset: 600mAH Ni-Cd Battery
Base: 9V DC @ 400mA
Charger: 6V DC @ 200mA
Memory
9 Speed dial locations; up to 24 digits, ꢀ5 characters per location
Directory: 20 Memory locations (including the nine speed dial entries);
up to 24 digits, ꢀ5 characters per location
CID: 45 Memory locations
ADDITIONAL INFO
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Connect with the
answering system 32
A
F
About announcements 26
About call history 23
Additional information 35-47
Answering system
operation - remote access 32-33
Answering system
operation at the base 26-3ꢀ
Audible indicators 26
FCC, ACTA and IC regulations 45
Feature summary 28
D
Delete a number/name
stored in speed dial ꢀ8
Delete a number/name
stored in the directory 20
Delete records
G
Getting started 5-9
H
Handset operation ꢀꢀ
Handset ringer
style/battery save
Headset Jack ꢀ4
from call history 24
Desk/Table Installation
7
B
9
Dial a displayed number 24
Dial a speed dial number ꢀ8
Dial a number
from the directory 2ꢀ
Display screen
messages - caller ID 25
Display screen
messages - telephone operation ꢀ5
DSL Service ꢀ0, 37
Basic operation ꢀꢀ-33
Batteries 34
Battery care and maintenance 34
Before you begin
Belt clip (optional) ꢀ0
I
4
Installation 5-ꢀ0
Important safety instructions 44
Install Handset Battery
5
C
Call Transfer ꢀ3
Call screening/intercept 30
Caller ID 22-25
Charge the handset battery
Check for dial tone 8
Choose Location
Clear Message Waiting Alert ꢀ3
Connect Power and
Telephone Line Cords
L
Listen to, save &
E
8
delete messages 29
Edit a number/name
stored in speed dial ꢀ7
Edit a number/name
5
M
Maintenance 42
Message Waiting ꢀ2
stored in the directory ꢀ9
6
48 INDEX
Download from Www.Somanuals.com. All Manuals Search And Download.
Move a number/name
Speed dialing ꢀ6-ꢀ8
Store a call history
to the speed dial memory 2ꢀ
record in the directory 24
Store a number/
name in speed dial ꢀ6
Store a number/
O
Operating range ꢀ4
name in the directory ꢀ9
P
T
Parts check list
4
Telephone operation ꢀꢀ-ꢀ5
Technical Specifications 47
Telephone directory ꢀ9-2ꢀ
Temporary tone dialing ꢀ2
To delete your announcement
To review your
R
Range ꢀ4
Reassign locations in speed dial ꢀ8
Record a memo 30
Record your announcement 27
Remote access commands 32
Replacing the Handset Battery 34
Review call history 23
27
announcement at any time 27
Troubleshooting 35-4ꢀ
V
S
Voice menu 32
Set Handset date and time
Set language mode 8
9
W
Wall Mounting
7
Set the dial mode
8
Warranty statement 42
Window display 3ꢀ
Setting the clock 26
Setting up your
answering system 28
INDEX
49
Download from Www.Somanuals.com. All Manuals Search And Download.
VTECH TELECOMMUNICATIONS LTD.
A member of THE VTECH GROUP OF COMPANIES.
Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon
Distributed in Canada by VTech Telecommunications Canada Ltd., Richmond, B.C.
Copyright ©2005 for VTECH TELECOMMUNICATIONS LTD.
Printed in China.
9ꢀ-000499-070-000
M
Download from Www.Somanuals.com. All Manuals Search And Download.
|