VTech Cordless Telephone CS6120 2 User Manual

Battery installation and charging  
Set number of rings  
Install the battery as shown below. Once you have installed the  
battery, you may be able to make and receive short calls. For best  
performance, charge the handset battery continuously for at least  
16 hours.  
You can set the answering system to answer an incoming call  
after 2, 3, 4, 5 or 6 rings; or toll saver. If you choose toll saver,  
the answering system answers a call after 2 rings when you  
have new messages, or after 4 rings when you have no  
new messages.  
2
Quick start guide  
1
Place the battery with the  
wires inside the battery  
compartment.  
Plug the battery connector  
securely into the socket.  
1. Press MeNU when the handset is not in use.  
2. Scroll to answering sys then press SeLeCT.  
3. Scroll to ans sys setup then press SeLeCT.  
4. Scroll to # of rings then press SeLeCT.  
CS6120-2/CS6124  
5. Press CID or  
to choose 6, 5, 4, 3, 2 or Toll saver and  
Introduction  
then press SeLeCT to save.  
This quick start guide provides you with the basic installation  
instructions. A limited set of features are described in  
abbreviated form.  
record your own announcement  
You can use the preset announcement to answer calls, or replace it  
with your own recorded announcement. The announcement can be  
up to 90 seconds in length.  
Please refer to the online user’s manual for complete installation  
and operation instructions.  
3
4
Slide the battery  
Charge the handset in the  
telephone base or charger.  
1. Press MeNU when the handset is not in use.  
2. Scroll to answering Sys then press SeLeCT twice.  
3. Press 7 to record.  
Telephone base and charger installation  
Install the telephone base and charger as shown below.  
compartment cover towards  
the center of the handset  
until it clicks into place.  
Telephone wall jack  
Electrical outlet  
4. After the handset announces, “Record after the tone. Press 5  
when you are done,” speak towards the handset microphone.  
(not controlled by  
a wall switch)  
Charge light  
remains on  
when charging.  
A DSL filter  
5. Press 5 when done.  
(not included)  
is required if  
you have DSL  
high-speed  
6. Press 2 to play the recorded announcement; or 7 to record  
again if desired. Press 3 to delete the recorded announcement.  
Press 5 to stop the playback at any time.  
Telephone base  
power adapter  
Charger  
adapter  
Internet service  
Telephone  
line cord  
Charger  
enter the handset menu  
Telephone base  
1. Press MeNU when the phone is not in use.  
2. Press CID or  
until the screen displays the desired  
Use only the power adapters and batteries supplied with  
this product.  
feature menu.  
3. Press SeLeCT to enter that menu.  
• To return to the previous menu, press CaNCeL.  
• To return to idle mode, press and hold CaNCeL.  
IMPOrTaNT!  
Set date and time  
Refer to the online user’s manual for a full set of installation and  
operation instructions. For manual download or customer service,  
or call 1 (800) 267-7377.  
1. Press MeNU when the handset is not in use.  
2. Scroll to Settings then press SeLeCT.  
3. Scroll to Set date/time then press SeLeCT.  
4. Use the dialing keys (0-9) to enter the current month, date and  
year. Then press SeLeCT.  
Copyright © 2011 for VTECH TELECOMMUNICATIONS LTD.  
All rights reserved. Printed in China.  
96-007701-050-100  
5. Use the dialing keys (0-9) to enter the hour and minute. Then  
press CID or  
to select aM or PM.  
6. Press SeLeCT to save.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Taylor Weather Radio 1528 User Manual
Toshiba DVD Player SD 4700 User Manual
Toshiba Printer B EV4D User Manual
TRENDnet Network Card TEW 603PI User Manual
Tripp Lite Power Supply SUINT1000XL User Manual
Tripp Lite Power Supply WEXT5 5000TEL User Manual
U Line Refrigerator U 2175RFB 00 User Manual
UNICOM Electric Switch SmartGST 2404GM User Manual
Vienna Acoustics Speaker Subson User Manual
Wayne Plumbing Product RPP50 User Manual