d1789 series user's Guide
You will also find:
what's in the box?
Accessory handset and
D1789 base with answering
system and corded handset
charger
Not pictured:
x Rechargeable battery
(BT-1025)
x Battery cover
x AC adapter (PS-0035)
You should
have:
If you purchased
model number:
D1789
D1789-2
1 of each
2 of each
Wall/Desk
Stand
D1789-11
D1789-12
11 of each
12 of each
Not pictured:
x Coiled handset cord
x AC adapter (PS-0034)
x Telephone cord
* If the model number ends in R,
your package includes a DRX100
range extender. Refer to the
DRX100 User’s Guide for details.
•
•
If any items are missing or damaged, contact our Customer Care Line immediately. Never use
damaged products!
if You...
Contact uniden’s...
Phone number
817-858-2929 or 800-
297-1023
have a question or problem
Customer Care Line*
need a replacement part or an
accessory
Parts Department*
800-554-3988
need special assistance due to a
disability
800-874-9314
(voice or TTY)
Accessibility Help Line
*
During regular business hours, Central Standard Time; see our website for detailed business hours.
© 2012 Uniden America Corp.
Ft. Worth, Texas
Printed in Vietnam
U01UN474EZZ(0)
Download from Www.Somanuals.com. All Manuals Search And Download.
GettinG staRted
set uP the base
attach the stand
Before you attach the stand, you have to decide if you want the phone to rest on a desk or hang
on a wall.
For desktop use
1. Turn the stand so the word Desk is right-side up (it
will be on the left).
2. Insert the tabs into the notches marked Desk at the
top of the base.
DESK
A L W L
DESK
WALL
3. Slide the stand up until it snaps into place.
For wall mount use
1. Turn the stand so the word Wall is right-side up (it
will be on the left).
DESK
WALL
D E S K
WALL
2. Insert the tabs into the notches marked Wall at the
bottom of the base.
3. Slide the stand down until it snaps into place.
to Remove the stand
Pull the locking tabs up and back. Then, slide the stand straight off the opposite direction you
put it on.
Connect the Corded handset
Use the coiled cord to connect the corded handset to the connector on the left side of the base.
For wall mount use only
1. On the front of the base, pull the clip (that holds
the corded handset in place) out of its slot.
2. Rotate the clip 180 degrees.
3. Flip it from front to back and slide it back into the slot.
Connect the Power and telephone Cords
1. Connect the base AC adapter to the
jack. Route the cords as shown.
jack and the telephone cord to the
TEL LINE
AC IN 7.8V
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 3
for desktop use
for wall mount use
DESK
D E S K
WALL
WALL
A L W L
DESK
DESK
WALL
2. Plug the AC adapter into a standard 120V AC power outlet, and connect the telephone cord
to a standard telephone wall jack.
3. If you are mounting the phone on the wall, place the mounting slots over the pins on the wall
plate; slide the base down to lock it into place.
test the Connection
Pick up the corded handset from the base. You should hear a dial tone and the display on the
base should say Talk. When you get a dial tone, make a quick test call.
if...
try...
the display says Check TEL Line or you
don’t hear a dial tone
checking the connection between the base
and the phone jack.
you keep hearing a dial tone
changing to pulse dialing.
Changing to Pulse dialing
Your phone uses tone dialing by default. If your phone company uses pulse dialing, you need to
change your phone’s dial mode.
1. Press Menu on the base or Menu/select from the cordless handset and choose Global Setup
.
2. Select Dial Mode then Pulse. You’ll hear a confirmation tone.
To send DTMF tones during a call (e.g., for an automated response system), press to
*
temporarily switch to tone dialing. When you hang up, the phone automatically returns to pulse
dialing.
set uP the aCCessoRY handsets
install and Charge the battery
1. Unpack all handsets, battery packs, and battery covers.
If you need to remove a cover, press in on the notch and slide
the cover down and off.
2. Line up the battery connector with the jack inside the handset;
the connector only fits one way.
3. Push the connector in until it clicks into place; tug gently on the wires to make sure the
battery is securely connected.
4. Replace the battery cover and slide it into place.
Connect the Charger
1. Use an AC adapter to connect the power jack on each charger to a regular indoor (120V AC)
power outlet.
Download from Www.Somanuals.com. All Manuals Search And Download.
4 - English
2. Place each handset in a charger with the display facing forward. If the display doesn’t light
#uCph,arersgeeatatlhl heahnanddsesettsocrocmonpnleetcetltyhe(acbhoaurgte1r5tohaoudirfsf)ebreenftooruetulesti.ng.
test the Connection
Pick up each cordless handset and press HOMe/flasH. You should hear a dial tone and the display
should say Talk
.
If there is noise or static, see page 24 for tips on avoiding interference.
settinG uP the CelllinK™ bluetooth™ ConneCtion
The new D1789 with CellLink technology can connect with cellular phones that support the
Bluetooth V2.1 handsfree profile.
•
•
•
If you are not certain of the profiles supported by your Bluetooth phone or if you have
difficulty pairing your cellular phone to the D1789, see the manual that came with your
cellular phone.
With the CellLink feature, you can essentially treat your cellular phone as a second line. You
can use the D1789 handset to make and receive calls on your cellular phone number, put
cellular calls on hold, and transfer calls to other handsets. See page 13 for more information.
Bluetooth wireless devices have a maximum range of about 30 feet (9 m); the actual range will
vary depending on local conditions (obstacles, battery power, interference, etc.).
Pair your bluetooth phone
Pairing “introduces” the Bluetooth device and the D1789 and gives them permission to connect
to each other. In most cases, once you pair a cellular phone to the D1789, these devices connect
automatically whenever they detect each other. (If you have to manually reconnect each time,
check the Bluetooth settings on your cellular phone.) You can pair your Bluetooth devices
through the D1789 station.
1. Press Menu on the base or Menu/select on the cordless handset to display the main menu.
2. Select the Bluetooth Setup menu, then select the Add Cellular submenu. The base goes into
pairing mode when the station displays Search & select from Cellular D1789 PIN: 0000
.
3. On your Bluetooth phone, start a search for other Bluetooth devices. (This process may
take several seconds and it will be different for each cellular phone. See your cellular phone
owner’s manual for detailed instructions.)
4. Your cellular phone should discover a device called D1789 or Handsfree device. When your
cellular phone asks if you want to pair with this device, answer yes.
5. If your cellular phone prompts you for a PIN code or password to pair with the D1789, enter
0000 (four zeroes).
6. When your cellular phone accepts the Bluetooth connection, the D1789 sounds a
confirmation tone. The Bluetooth device number icon on the base and the handset display
light up.
# most cellular phones automatically transfer the audio to a bluetooth device as soon
as it pairs; if yours does not, look in your cellular phone’s bluetooth setup for a
“transfer audio” or “send audio to device” option.
to test the connection
1. Pick up a handset from its cradle (corded or cordless handset).
2. Dial the number you want to call, then press cell. You may not hear a dial tone or ringing,
but Talk displays.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 5
3. Make sure the call connects and you can hear clearly. (When you’re finished, press enD to
hang up.)
•
The D1789 remembers the pairing information for your cellular phone; if it loses
connection with your cellular phone for any reason (e.g., the cellular phone travels out
of range, runs out of charge, etc.), the D1789 can automatically reconnect the next time
your cellular phone becomes available.
using the d1789 with multiple bluetooth phones
•
The D1789 can save the pairing information for up to two different Bluetooth phones, but it
can only use one cellular line at any given time. For example, if you pair the D1789 to more
than one Bluetooth phone, when you press cell on the station, the D1789 asks which cellular
phone you want to connect to.
•
If you are using the D1789 to talk on one Bluetooth phone, the D1789 will not ring if a call
comes in on another cellular phone.
•
•
You can set a different ring tone for each paired cellular phone (see page 11).
To pair another Bluetooth phone, just repeat the pairing procedure with the new cellular
phone. (If the paired cellular phones interfere when you’re pairing the new one, just turn off
Bluetooth on any paired cellular phones until you finish pairing the new one.
GettinG to Know YouR Phone
PaRts of the base
CLEAR/FLASH
LCD
display
PHONEBOOK
MENU SELECT
Hook switch
Handset clip
SILENT
UP
CID
PLAY/STOP
DOWN
ANS ON/OFF
DELETE
Speaker
12-key dial pad
CELL SPEAKER
HOME SPEAKER
Microphone
REDIAL/
PAUSE
INTERCOM/
FIND HS
MUTE
Key (icon)
what it does
While entering text: delete the last character (press and hold to delete
all the characters).
clear/flasH
During a call: switch to a waiting call.
Menu
Opens the menu.
select
In any menu or list: select the highlighted item.
Download from Www.Somanuals.com. All Manuals Search And Download.
6 - English
Key (icon)
what it does
In standby: press and hold to turn off the ringer on the base or any
registered handset (see page 19).
silent
x In standby or during a call: open the phonebook.
x In the menu: go back to the previous screen.
x When entering text: move the cursor to the left.
x In the first 2 seconds of a message: go to the previous message.
x Anytime after the first 2 seconds of a message: restart the current
message.
PHOnebOOk
(
)
x In standby: begin message playback.
x In any menu or list, or while a message is playing: stop the current
operation and exit completely.
Play/stOP
x While the phone is ringing: ignore this call (mute the ringer).
x In standby: increase the ringer volume.
x During a call or while a message is playing: increase the volume.
x In any menu or list: move the cursor up one line.
uP (
ciD
)
x In standby or during a call: open the caller ID list.
x When entering text: move the cursor to the right.
x While a message is playing: skip to the next message.
x In standby: decrease the ringer volume.
x During a call or while a message is playing: decrease the volume.
x In any menu or list: move the cursor down one line.
DOWn (
)
x In standby: press and listen to the guidance. Press again to Delete All.
x In message playback: delete this message.
x When a call comes in on a paired Bluetooth phone and while this phone
is ringing: block this call.
Delete (
)
ansWer On/Off
Mute
In standby: turn the answering system on or off.
x While the phone is ringing: ignore this call (mute the ringer).
x During a call: mute the microphone.
x In standby: start a speakerphone call (get a dial tone).
x During a normal call: switch to the speakerphone.
x During a speakerphone call: hang up.
HOMe
x In standby: open the redial list.
x When entering a phone number: insert a 2-second pause.
reDial/Pause
cell
x In standby: start a telephone call using a paired Bluetooth phone.
x While a paired phone is ringing: answer the incoming call.
x During a CellLink call: hang up.
x In standby: page a handset using the intercom.
x During a call: put the call on hold and start a call transfer.
intercOM/finD Hs
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 7
PaRts of the handset
LCD
Display
END/
CLEAR
12-key
dial pad
Earpiece
UP
CID
CELL
SPEAKER
MESSAGE/
MUTE
Charging
contacts
Microphone
REDIAL/
PAUSE
Status
MENU/
SELECT
DOWN
HOME/
FLASH
PHONEBOOK
Key (icon)
uP
what it does
x In standby: increase the ringer volume.
x During a call: increase the audio volume.
(
)
x In any menu or list: move the cursor up one line.
x During a call: hang up.
x In the menu or any list: exit and go to standby.
x When entering text or numbers: erase the character at the cursor (press &
hold to erase all characters).
enD/clear
x In standby or during a call: open the caller ID list.
x When entering text: move the cursor to the right.
ciD
x In standby: start a telephone call using a paired Bluetooth phone.
x While a paired cellular phone is ringing: answer the incoming call.
x During a CellLink call: switch to a waiting call.
cell
x Switch a normal call to the speakerphone (and back).
sPeaker
(
)
x In standby: access your answering system.
x During a call: mute the microphone.
x While the phone is ringing: ignore this call (mute the ringer).
Message/Mute
(
)
x In standby or during a call: open the phonebook.
x In the menu: go back to the previous screen.
x When entering text: move the cursor to the left.
PHOnebOOk
(
)
x Open the menu.
x In the menu or any list: select the highlighted item.
Menu/select
HOMe/flasH
x In standby: start a telephone call on your landline (get a dial tone).
x While the landline is ringing: answer the incoming call.
x During a call: switch to a waiting call.
x In standby: decrease the ringer volume.
x During a call: decrease the audio volume.
x In any menu or list: move the cursor down one line.
DOWn
(
)
x In standby: open the redial list.
x When entering a phone number: insert a 2-second pause.
reDial/Pause
Download from Www.Somanuals.com. All Manuals Search And Download.
8 - English
Reading the displays
Status
icons
Base info
Current
call info
CID info
Time
Home
12:08PM
Date and new
message icon
7/10
*
Answering
system
status
UP or DOWN
Time &
date
Status icons
TAD status icons
Base LCD Display
Handset LCD Display
You can use the uP and DOWn keys to scroll through CID lists and phonebook entries.
icon
what it means
Base:
Landline status.
Handset:
Base:
Cellular line status.
Handset:
P
Base:
Privacy Mode is on; no other station can join the call.
Handset: P
The ringer is turned off and will not ring for new calls.
You have a voice message waiting.
Base:
1 2
Bluetooth device number linked to the D1789.
Handset:
Base: Off
On
TAD status (ON or OFF). The number of TAD messages are also
displayed.
Handset:
Base:
Indicates a new message received.
Handset:
New message symbol: an asterisk * icon indicates a new message
or a message not retrieved.
*
[Aa] [aA]
Enter 1) capital or 2) lower case letters (see page 12).
▲
▼
uP and DOWn keys are active.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 9
icon
what it means
Handset-Only Icons
The speakerphone is on.
Home phone line.
The handset is using ECO (power save) mode.
The signal from the base is 1) weak through 4) strong.
The battery is 1) full, 2) half charged, 3) getting low or 4) empty.
usinG the menus
Press Menu on the base or Menu/select on the handset to access the menus. Press PHOnebOOk to go
back one screen. Press clear on the base or press and hold enD/clear on the cordless handset to
return to standby. If you don’t press any keys for about 30 seconds, the station exits the menu.
During a call, press PHOnebOOk on the base or HOMe/flasH on the cordless handset to back out of
the menu without hanging up.
With the phone in standby, press
MENU/SELECT
to open the menu.
MENU/SELECT
Press
option.
to choose that
Bluetooth Setup
Handset Setup
Handset Setup
T-coil
T-Coil
Press
PHONEBOOK
Off
to
go back a screen
OR
UP
Use and
DOWN
to
select a menu.
END
press
to exit
the menu.
Intercom menu (handset menu only)
The Intercom menu sets up 2-way communication. You can connect a handset to a handset
or a handset to the base. You can also use the Intercom menu to page the handsets (find a lost
handset).
Bluetooth Setup menu
When you access the Bluetooth Setup menu for the first time, the system prompts you to Add
Cellular. Once you have paired a cellular phone, more options display for this menu.
menu option
what it does
Add Cellular
Pairs cellular phone with base. This option displays if less than
2 cellular phones are paired to the base.
Make Call
Select a cellular phone for an outgoing call.
Download from Www.Somanuals.com. All Manuals Search And Download.
10 - English
menu option
what it does
Privacy Setup
Determines which handsets will ring when a cellular call
comes in (on = ringing enabled). Each station can determine
whether it will ring when a call from that cellular phone comes
in.
Download PB
Downloads the cellular phone’s phonebook to the base.
Un-pairs a cellular phone from the base.
Remove Cellular
Handset Setup menu (handset menu only)
You can change these settings separately for each station.
menu option
what it does
Turn on T-coil mode to reduce noise on hearing aids equipped
with a telecoil (T-coil) feature. T-coil mode shortens talk time, so
keep your battery fully charged.
T-coil
Select a phone, then choose that phone’s ring tone. As you
Ringer Tones
Personal Ring
AutoTalk
highlight each ring tone, you hear a sample. Press Menu/select.
Turn on personal ring so you can assign a special ring tone to
people in your phonebook. With Caller ID, this handset uses the
assigned tone when the person calls.
Have this handset answer a call when you pick it up from the
charger (without pressing any buttons).
Have this handset answer a call when you press any key on the
12-key dial pad.
Any Key Answer
Banner
Change the name on the handset's display. (10 char. max.)
HandsetLanguage Change the display language.
Key Touch Tone
Have the keypad sound a tone when you press a key.
Base Setup menu (base menu only)
These settings apply to the base only.
menu option
Language
what it does
Change the display language.
Key Touch Tone
LCD Contrast
Have the keypad sound a tone when you press a key.
Change the contrast of the display.
Answering Setup menu
Refer to page 20 for details on setting up your answering system.
Date & Time menu
Use this menu to set the clock (if you have Caller ID, the phone sets date and time automatically).
Enter the date and time (MM/DD/YY/HH/MM); select AM or PM. Use ciD to move the cursor
past a digit without changing it.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 11
Global Setup menu
The settings on this menu affect all stations. Only one station at a time can change these menu
options.
menu option
what it does
Dial Mode
Choose tone or pulse dialing (see page 4).
Enter, edit, or delete the access number for your voice mail
service (see page 20).
Edit Voice Mail
Edit Int’l No.
Set Line Mode
VMWI Reset
Enter, edit, or delete international numbers.
Change this setting only if instructed to by customer service.
Reset the Voice Message Waiting Indicator (see page 20).
Base: Time Adjustment
HS: CID Time Setting
Select On if you want the CID function to supply the time.
Select Off for the system clock to do it.
Register Accy. menu (base menu only)
This menu puts the base in registration mode (see page 25).
entering text on Your Phone
•
Use the 12-key dial pad anytime you want to enter text into your phone (a name in the
phonebook, the handset banner, etc.).
•
If two letters in a row use the same key, enter the first letter; wait for the cursor to move to the
next space and enter the second letter.
to...
Press...
move the cursor left
PHOnebOOk
.
move the cursor right
ciD.
erase the character at the cursor
enter a blank space
clear
.
#
.
switch between upper and lower case letters
rotate through the punctuation and symbols
enter a “ + “
.
*
0
.
0
.
and hold
usinG YouR Phone
maKinG landline Calls
from base
Corded
handset
Pick up the
from handset
earpiece speaker-phone
Press HOMe/
flasH
Press HOMe/
flasH
to...
speaker-
phone
make a call, dial
the number, then handset.
Press HOMe.
Press sPeaker
.
.
Pick up the
answer a call
Press HOMe
.
Press sPeaker
.
handset.
.
Place handset in
cradle.
Press enD or place the handset in
the charger.
hang up
Press HOMe
.
Download from Www.Somanuals.com. All Manuals Search And Download.
12 - English
from base
from handset
earpiece speaker-phone
to...
Corded
handset
speaker-
phone
switch to the
speakerphone
and back
Pick up the
handset.
Press HOMe
.
Press sPeaker.
Press Menu/select and select
put a call on hold* Press and hold intercOM/finD Hs.
Hold/Transfer
.
return to a call on
hold*
Press HOMe/
flasH.
Press HOMe
.
Press sPeaker.
mute the ringer
Press Mute
.
Press Mute.
* After 5 minutes on hold, the call will be disconnected.
maKinG bluetooth Calls
After you have paired your cellular phone with the D1789, you can make and receive calls from
your cellular phone through the D1789.
from base
from handset
speaker-
phone
to...
Corded
handset
speaker-
earpiece
phone
make a call, dial the number, Press cell. If more than one cellular phone is paired, you
then
are prompted to select one.
Press cell. If more than one cellular phone is paired, you
are prompted to select one.
answer a call
Press cell or place the
handset in the cradle.
Press enD or place the
handset in the charger.
hang up
switch from the landline to
CellLink (automatic hold)*
Press Menu and select Hold/
Press Menu/select and
select Hold/Transfer.
Transfer
.
Switch from CellLink to the
landline (automatic hold)*
Press HOMe.
Press HOMe/flasH.
Press the hook Press cell
Press cell or Press cell or
return to a call on hold*
switch or cell
.
or HOMe
.
HOMe/flasH sPeaker.
.
* After 5 minutes on hold, the call will be disconnected.
Once you have paired a cellular phone, the following operations are available through the
Bluetooth Setup menu:
to...
from the Bluetooth Setup menu, select a cellular phone
and then select...
make a CellLink call
Make Call; enter the number to call and press cell.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 13
to...
from the Bluetooth Setup menu, select a cellular phone
and then select...
Privacy Setup, then set Privacy to On or Off
.
x All stations set to Off: All stations will ring (default).
x One or more stations set to On: Only stations set to On will ring;
other stations do not ring but they can still receive calls.
# the Privacy option only affects the ring. all stations
still get Cid information and can use the cellular phone
to make and receive calls.
set Privacy features
Download PB. The screen displays Download PB Completed
when finished.
download phonebook
delete Bluetooth
pairing
Remove Cellular. The screen displays Removed Cellular when
complete.
relink a cellular phone
Connect.
# to add another cellular phone, use the same procedures on page 5.
ChanGinG the Volume
to change the...
when...
Press...
earpiece or speaker volume
for each handset
uP to increase the
volume.
you are listening to that earpiece or
speaker (playing messages, etc.)
base speaker volume
DOWn to decrease
it.
ringer volume for each
handset or the base*
the phone is in standby
* If you turn the ringer all the way down, that particular ringer turns off.
usinG the CalleR id and Redial lists
Caller ID (CID) is a service available from your telephone provider that shows the phone number
(and sometimes the caller’s name) of incoming calls. Contact your telephone provider for more
information.
Caller id list
Redial list
x The phone saves the information for the last 50 incoming
x Each station remembers the
last 10 numbers you dialed
on it.
x Only one station can access
its redial list at a time.
x The station does not record
which line was used to call
the number.
calls (both landline and CellLink calls) to the CID list. An
*
asterisk ( ) marks any calls received since the last time you
checked the CID list.
x All stations share the same CID list so only one station can
access the list at a time.
x In standby, stations show how many calls came in since the
last time you checked the CID list.
Download from Www.Somanuals.com. All Manuals Search And Download.
14 - English
to…
Press...
ciD on the base, press Menu, and select View Number. The CID
entries display.
open the CID list
ciD on the handset, then use the uP and DOWn keys to enter the
list. Up to 10 entries display at a time.
open the redial list
reDial/Pause.
DOWn to scroll from newest to oldest.
uP to scroll from oldest to newest.
scroll through the lists
HOMe/flasH on the cordless handset or pick up the corded
dial this number from
the landline
handset from the base. (If the number is a toll call but there is
no 1 at the beginning, press to add 1 before dialing.)
*
cell. If you have two or more cellular phones paired, select
the cellular phone you want and press select on the base or
Menu/select on the cordless handset. Press cell again to dial
the number. (If the number is a toll call but there is no 1 at the
dial this number from
the CellLink
beginning, press to add 1 before dialing.)
*
review current CID
record details
Menu on the base or Menu/select on the cordless handset to
display options for that record.
x
x
once to add 1 for a toll call.
twice to add the International code to the CID number.
add other digits and
codes to the CID
number
*
*
# Press a third time to return to normal mode.
enD on the handset or Play/stOP on the base.
*
close the lists
Once you select a specific CID record to display (see “To review current CID record details” in
the previous table), menu options display for that record.
to...
select...
Erase the CID number from the list. Delete Entry
Add the CID number to the
phonebook.
Store Into PB . The phone displays the Edit Name
screen. Enter the name and number for this entry.
Delete all CID entries.
Delete All (HS only)
usinG Call waitinG
•
Call Waiting, a service available from your telephone provider, lets you receive calls while
you are on another call. Caller ID on Call Waiting (CIDCW) service displays Caller ID
information for a waiting call.
•
If you get a Call Waiting call, the phone sounds a tone and displays any CID information
received from the waiting call. Press clear/flasH on the base or HOMe/flasH on the cordless
handset on the landline (or cell for a cellular phone call) to switch between the current call
and the waiting call; each time you switch, there is a short pause before you’re connected to
the other call.
PhonebooKs
•
In addition to the home phonebook’s 100 entries, you can download phonebooks from the
paired cellular phones (700 entries each, up to 1400 entries total).
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 15
•
•
The home phonebook is stored separately from any downloaded phonebooks.
All stations can access the phonebooks, but only one station can access the phonebooks at a
time.
using the Phonebook
to...
Press...
open the phonebook
PHOnebOOk, select the phone name, then View Number.
DOWn to scroll through the entries from A to Z.
uP to scroll from Z to A.
ciD to view detail information.
review your entries
PHOnebOOk to return to the previous display.
jump to entries that start
with a certain letter
(Select View Number from a
phonebook list, then...)
the number key corresponding to the first letter of the
entry you want. Press the number key again for the next
letter and the list will narrow down to entries with only
those letters.
dial the selected entry
using your landline
HOMe/flasH on the cordless handset or pick up the corded
handset from the base.
cell. If you have more than one cellular phone paired, use
uP / DOWn to highlight the cellular phone you want to call
out on and then press select on the base or Menu/select on
the handset.
dial an entry using your
cellular line from the
CellLink
review the current entry’s Menu/select on the cordless handset or select on the base
details
after scrolling to the desired phonebook entry.
copy a selected cellular
phonebook entry to the
home phonebook
select then Menu on the base or Menu/select on the cordless
handset. From the available options, select Store into PB. A
confirmation tone sounds and Done! displays.
Menu/select on the cordless handset or select on the base to
edit the current entry
open the menu, then select Edit
.
Menu/select on the cordless handset or select on the base
delete the current entry
and then select Delete. When the system prompts you to
confirm, select Yes
.
close or exit the
phonebook
Play/stOP on the base or press and hold enD on the handset.
adding Phonebook entries
With the phone in standby, open the phonebook. Press Menu on the base or Menu/select on the
cordless handset and select Create New. Enter a name, number, and a personal ring if desired.
•
•
Enter the phone number (up to 32 digits) exactly as you would dial it.
If you need the phone to wait before sending the next set of digits, press reDial/Pause to insert
a 2-second pause. You can insert multiple pauses, but each one counts as a digit (you’ll see P
in the display).
downloading Cellular Phonebooks
You can download up to 700 names per cellular phonebook (1400 total) to the phonebook.
Download from Www.Somanuals.com. All Manuals Search And Download.
16 - English
1. Press Menu on the base or Menu/select on the cordless handset and select Bluetooth Setup. Scroll to
Download PB and select it.
2. The Bluetooth icon on the LCD display will show the device number of the downloading
phonebook (for Bluetooth device #1:
.)
3. Download PB Completed displays when the download is completed. Download PB Failed
displays if the download fails.
deleting all the Phonebook entries
With the phone in standby, open the phonebook. Press Menu on the base or Menu/select on the
cordless handset and select Delete All. When the phone prompts you to confirm, select Yes
.
usinG sPeCial featuRes
off-hooK menus
When you are in a call, pressing Menu on the base or Menu/select on the cordless handset brings
up special off-hook menus:
menu option
what it does
Hold/Transfer
In a call: puts the call on hold. Once the call is on hold, you page
a specific handset or base to transfer the call to or page the base
and all the handsets.
Call Privacy
Determines which handsets will ring when a cellular call comes in
(default = ALL).
Hold/Transfer menu
This off-hook menu lets you put calls on hold. Once the incoming call is on hold, you can page
and speak to another station, transfer the call to another station, or release the call and resume
speaking.
to...
from the base...
from the cordless handset...
put a call on
hold
Press intercOM/finD Hs on the
base.
Press Menu/select on the cordless
handset and select Hold/Transfer.
take a call off of Press intercOM/finD Hs on the
Press Menu/select on the cordless
handset.
hold
base.
1. Press Menu/select and select
Hold/Transfer from the off-hook
menus. The call is now on hold.
1. Press intercOM/finD Hs. The
call is now on hold.
2. The system prompts you
to select a handset (or all
handsets) to page. Press
2. The system prompts you
to select a handset (or all
transfer a call
handsets) to page. Press Menu/
select
.
select
.
3. Once the answering station
accepts your call and speaks
with you, press intercOM/finD
Hs again to transfer the call.
3. Once the answering station
accepts your call and speaks
with you, press Menu/select
again to transfer the call.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 17
to...
from the base...
from the cordless handset...
Pick up the receiver or press
accept a page
Press HOMe/flasH
.
HOMe
.
cancel a transfer Press intercOM/finD Hs or HOMe
.
Press HOMe/flasH
.
Call Privacy menu
To activate Call Privacy mode on a call in progress, press Menu on the base or Menu/select on the
P
cordless handset, then select Call Privacy. As long as Call Privacy mode is on, you’ll see a on
the base or
on the cordless handset display, and no other handsets can join your call. Call
privacy mode turns off automatically when you hang up; you can turn off call privacy the same
way you turn it on - by pressing Menu on the base or Menu/select on the cordless handset, then
selecting Call Privacy
.
multistation featuRes
# to use the features in this section, you need at least 1 cordless handset.
•
Your base supports a total of 12 cordless handsets: the ones that came with your D1789
system and up to 11 more DCX170BT accessory handsets. It also supports a total of 2 DRX100
range extenders, including any that came with your phone.
•
•
•
You must register accessory handsets to the base before using them. (Handsets that came
packaged with the base are already registered.)
Handsets that aren’t registered display a Not Registered message. For registration
instructions, see page 25 or the accessory handset manual.
If a handset was ever registered to a base, you must reset it before it can register to a new base;
see page 25 or the accessory handset manual.
Conference Calling
•
•
•
When an outside call comes in, two stations and one cellular phone can join in a conference
call with the outside caller.
To join a call that’s already in progress, press HOMe on the base or HOMe/flasH on the cordless
handset.
To leave the conference call, hang up normally; the other handset remains connected to the
call.
intercom
•
•
•
•
Whenever the phone is in standby, you can make an intercom call between stations without
using the phone line.
You can make an intercom call from any station, but only two stations can be in an intercom
call at any time.
If an outside call comes in during an intercom page, the phone cancels the page so you can
answer the incoming call.
If an outside call comes in during an intercom call, press clear/flasH on the base, HOMe/flasH
on the cordless handset, or cell, or pick up the corded handset from the base, depending on
which line is ringing, to hang up the intercom call and answer the outside call.
Download from Www.Somanuals.com. All Manuals Search And Download.
18 - English
to...
from the base, press...
from a cordless handset, press...
Menu/select, then Intercom
intercOM/finD Hs.
.
make an
intercom page
Select the station you want to talk with or All to page all stations at
the same time.
intercOM/finD Hs or hang up
enD.
cancel a page
answer a page
the corded handset.
HOMe or pick up the corded
HOMe/flasH.
handset.
end an
intercom call
intercOM/finD Hs
.
enD.
silent mode
You can silence the ringers on the base and all handsets for a specific period of time; the
answering system answers any incoming calls without playing anything through the speaker.
1. With the phone in standby, press silent on the base or #/silent on the cordless handset. The
phone prompts you to select the number of hours (
1
-
9
or Always On) that you want it to stay
in Silent mode.
2. To confirm, press select on the base or Menu/select on the cordless handset or just wait about
5 seconds. The phone turns on the answering system and displays Silent Mode On on each
station.
3. After the selected number of hours, the phone automatically exits Silent mode. To exit Silent
#mifotdheempahnounaelliys, ipnressisleanntdmhooldde and you turn off the answering system, the phone
silent on the base or #/silent on the cordless handset again.
exits silent mode.
Chain dialinG
If you often have to enter a series of digits or a code number during a call, you can save that code
number to a phonebook entry and use the phonebook to send the code number.
1. Enter the code number (up to 32 digits) into the phonebook just like a regular phonebook
entry. Be sure to enter the code number into the phonebook exactly as you would enter it
during a call.
2. When you hear the prompt that tells you to enter the number, open the phonebook and find
the entry that contains your code number.
3. Press select on the base or Menu/select on the cordless handset twice to send the code. If you
change your mind, just close the phonebook.
VoiCe messaGe notifiCation
If you subscribe to a landline’s voice mail service, your phone can notify you when you have
a new message. This feature supports Frequency-Shift Keying (FSK) notification. Contact
your voice mail provider for information. The D1789 does not notify you when you have a new
CellLink voice mail.
When you have new messages, the display shows a message icon. To access your voice mail from
the base, call the provider’s access number and enter the access code. To access your voice mail
from the cordless handset, press Message/Mute and select Voice Mail
.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 19
# when you select Voice Mail on the cordless handset, you will be prompted to enter
a Voice mail access number if you have not yet set one up. if you have already set
one up, your phone will dial it. if you want to edit or delete your Voice mail access
number, select Global Setup/Edit Voice Mail to delete the number and then re-enter a
different number.
After you listen to your messages, the message icon turns off. If it doesn’t, you can reset it. With
the phone in standby, open the menu and select Global Setup; select VMWI Reset, then select Yes
.
usinG YouR Phone duRinG a PoweR failuRe
If there is a power failure, you can still make and receive phone calls using the base corded
handset, including Call Waiting calls and changing the earpiece volume. All other features of
the base and all cordless handsets will not function.
# while the power is out, the base uses a special ringer; you cannot adjust the volume
of this ringer.
findinG a lost handset
You can page the stations to locate a lost handset through the Intercom menu. All handsets beep
for 1 minute; to cancel, press intercOM/finD Hs on the base or enD on the cordless handset.
usinG the answeRinG sYstem
# the answering system works with landline calls only.
answeRinG sYstem oPtions (ANSWERING SETuP menu)
You can set or change the answering system options from any station. Just open the menu and
select Answering Setup
.
select this option...
to...
Enter a 2-digit PIN so you can access your answering system
from any touch-tone phone (see page 22).
Security Code
Set the number of rings (
2
,
4
, or 6) before the system answers.
Ring Time
Toll Saver makes the system answer after 2 rings if you have
new messages or after 4 rings if you don't.
Set the amount of time (1 or 4 minutes) callers have to leave a
message. Choose Announce Only if you don't want the system
to let callers leave a message.
Record Time
Message Alert
Have the system beep every 15 seconds when you have a
new message. The alert stops after you listen to all your new
messages or if you press any key on the base.
Ans. Language
Call Screen
Change the language of the system's voice prompts.
Turn on the call screen feature so you can hear callers through
the speaker as they leave messages (see page 22).
Turn your answering system on or off.
You can also press On/Off on the base.
Ans. On/Off
Record Greeting
Greeting Options
Record an outgoing message or greeting (see below).
Switch greetings or delete your greeting (see below).
Download from Www.Somanuals.com. All Manuals Search And Download.
20 - English
Personalizing the Greeting
Your personal outgoing message or greeting can be from 2 to 30 seconds long. If you don’t record
a greeting, the system uses a pre-recorded greeting: Hello, no one is available to take your call.
Please leave a message after the tone.
to...
follow these steps:
1. Open the menu with the phone in standby. Select Answering Setup
,
then Record Greeting
.
2. Press select on the base or Menu/select on the cordless handset to
start recording. Wait until the system says "Record greeting" before
speaking.
3. Press select on the base or Menu/select on the cordless handset to stop
recording. The system plays back your new greeting.
4. To keep the greeting, press Play/stOP on the base or enD on the
handset. To delete it and try again, press clear/flasH on the base or
intercOM/clear on the handset.
record a
personal
greeting
# Recording a greeting overwrites any previously recorded
greetings.
1. Open the menu with the phone in standby. Select Answering Setup
then Greeting Options
,
.
switch
between
greetings
2. The system plays back the current greeting. Press select on the
base or Menu/select on the cordless handset to switch between the
prerecorded greeting and the personal greeting.
delete your
greeting
Switch to your personal greeting, then press clear/flasH on the base or
intercOM/clear on the handset.
MESSAGE/MUTE
mote operation mode.
Press
to start
aCCessinG the answeRinG sYstem
When the phone’s in standby, you can access the answering
system from any handset; however, only 1 station can access
the answering system at a time.
1:Repeat 3:Skip
4:Delete 5:Stop
Press a correspond-
ing number key to
choose an operation
OR
to exit remote
operation mode.
•
•
After 30 seconds of inactivity, it returns to standby.
During remote access, the phone beeps so you know it’s
waiting for the next command.
END
•
During message playback, press Menu/select to open the
menu for playback control. You can press the number key
shown next to each command instead of scrolling through the screens.
to...
from the base
from a handset
Press Message/Mute and
select Play Message
Press Play/stOP.
.
play new
messages
The system announces the date, time, and the number of new and
old messages before playing each new message in the order it was
received. After the new messages play, the system plays the old
messages.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 21
to...
from the base
Wait at least 5 seconds after the message starts playing,
press PHOnebOOk. Press (number key).
Within 2 seconds after a message starts playing,
from a handset
restart this
message
1
replay an
earlier
message
press PHOnebOOk.
Press ciD
Press
Press
1
3
(number key).
(number key).
skip a
message
.
delete a
message
While a message is playing,
While a message is playing, press Delete
.
press
4
(number key).
delete all
messages
With the phone in standby, press Delete
;
Not available.
press Delete again to confirm.
After the system plays all new messages,
play old
messages
press Play/stOP again.
Press Play/stOP
Press
Press
2
(number key).
(number key).
stop
playback
.
5
sCReeninG YouR Calls
You can use the answering system for call screening. While the system takes a message, you can
listen on the base speaker (if you turn on Call Screen) or from a handset. Only one handset can
screen calls at a time. If another handset tries to screen calls, it beeps and returns to standby.
to...
from the base
from a handset
hear the caller leaving a
message
Listen to the caller over
the speaker.
Press Message/Mute
.
Pick up the corded
handset.
answer the call
Press HOMe/flasH.
mute the call screen without
answering*
Press enD or return the
handset to the charger.
Press Play/stOP
.
# if you mute the call screen, the system continues taking the message; it just stops
playing through the speaker.
usinG the answeRinG sYstem RemotelY
You can dial in to your answering system from any touch-tone phone. Before you can use this
feature, you must program a security code.
Programming a security Code
With the phone in standby, open the menu; select Answering Setup/Security Code. Use the
number keypad to enter a two-digit security code (01 to 99). Press select on the base or Menu/
select on the cordless handset when you’re finished.
# Remember to make a note of your new security code!
Download from Www.Somanuals.com. All Manuals Search And Download.
22 - English
dialing in to Your system
1. Call your phone number & wait until the system answers. (If the system is turned off, it
answers after 10 rings & sounds a series of beeps.)
0
2. During the greeting or beeps, press and immediately enter your security code. If you enter
it incorrectly three times, the system hangs up and returns to standby.
3. The system announces the time, the number of messages in memory, and a help prompt. It
beeps to let you know it's waiting for a command.
4.
#Wifhyeonuydoounh'teaprrbeesesping, enter a two-digit command from the chart.
any keys for 15
seconds, the
system hangs
up and return to
standby.
01
02
03
04
Repeat message
Play message
05 Stop playback
06 Turn the system on
09 Turn the system off
10 Hear help prompts
Skip message
Delete message
imPoRtant infoRmation
solVinG PRoblems
If you have any trouble with your phone, check this section first. If you need help, call our
Customer Care Line listed on the front cover.
General problems
Possible solutions
x Check the telephone cord connection.
x Disconnect the base AC adapter for a few minutes; then
reconnect it.
No stations can make or
receive calls.
A handset can’t make or
receive calls.
x Move the handset closer to the base.
The corded handset can
make calls but the cordless
handset(s) cannot.
x Check the power connection to the base. If the base
is unplugged or the power goes out, only the corded
handset can make and receive calls.
x Make sure the ringer is turned on.
x Make sure Silent mode is turned off (see page 19).
A station can make calls, but it
won’t ring.
x Charge the battery for 15-20 hours.
x Check the battery connection.
A handset is not working.
The phone keeps ringing
when I answer on an
extension.
x You may have to change the line mode. Contact
Customer Service for instructions.
audio issues
Possible solutions
x Move the handset closer to the base.
x Keep the handset’s battery fully charged.
Callers sound
weak or soft.
x Increase the earpiece volume.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 23
audio issues
Possible solutions
x Check for interference from appliances (microwave ovens, TVs, etc.) or
wireless devices (baby monitors, WiFi equipment, etc.). Move the handset
or base away from the interference source.
x If you use a telecoil hearing aid, turn on T-coil mode (see page 11).
x If you have any service that uses the phone line, add a DSL or telephone
line filter (see page 25).
There’s a lot of
noise or static
on the line
Caller id problems
Possible solutions
x Let calls ring twice before answering.
x Make sure your Caller ID service is active.
Caller ID information does
not display.
Caller ID displays briefly and
then clears.
x You may have to change the line mode. Contact
Customer Service for instructions.
multistation problems
I can’t transfer calls.
Possible solutions
x Reset all the stations (see page 25).
x See if any station is in Privacy Mode.
Two handsets can’t talk to a caller.
x Move the handset closer to the base.
x See if any station is in Privacy Mode.
A handset says unavailable
.
x Reset the handset (see page 25).
x See if you have 12 registered handsets.
I can’t register a new handset.
answering system problems
The answering system does not work.
Possible solutions
x Make sure the answering system is on.
x Make sure the base is plugged in.
x See if Record Time is set to Announce Only
x Delete messages (memory may be full).
.
The system won't record messages.
x See if another station is using the system.
x Make sure the phone is in standby.
A handset can't access the answering
system.
x If there was a power failure, re-record your
personal outgoing message.
My outgoing message is gone.
x Make sure call screening is turned on.
x Change the base speaker volume.
I can’t hear the base speaker.
Messages are incomplete.
x Increase the Record Time
.
x Delete messages (memory may be full).
The system keeps recording when I
answer on an extension.
x You may have to change the line mode. Contact
Customer Service for instructions.
bluetooth problems Possible solutions
x Making sure your cellular phone is in pairing mode.
x Check your cellular phone’s manual for instructions on Bluetooth
device pairing.
The D1789 won’t
pair with my phone. x Making sure your cellular phone supports the Bluetooth hands-free
profile.
x Checking the link order for that cellular phone.
Download from Www.Somanuals.com. All Manuals Search And Download.
24 - English
bluetooth problems Possible solutions
x Making sure your cellular phone has Bluetooth turned on.
x Making sure your cellular phone is in range of the base.
x Making sure the station’s ringer is not turned off. (The base doesn’t
ring on cellular calls.)
The D1789 doesn’t
ring when my
cellular phone does.
x Adjusting the volume.
The D1789 paired
with my phone, but
I can’t hear anything
through the station.
x Setting your cellular phone to transfer the audio to a Bluetooth
device. Check your phone’s manual for instructions on Bluetooth
setup and options.
x Erase the Bluetooth pairing and repair the cellular phone to the
base. To erase the Bluetooth pairing, see page 14.
installing a line filter or dsl filter
A telephone line filter or DSL filter prevents services that use the phone line from causing
interference on your phone. To get a line filter, contact your service provider or look in an
electronics store. Plug the filter into the telephone wall jack and plug the base into the filter.
Make a test call to make sure the noise is gone.
liquid damage
Caution: if the base is covered in liquid, disconnect the adapter & phone cord from
the wall before touching it.
If the liquid is only on the exterior housing of the base or handset, wipe it off and use as normal.
If you can hear liquid inside the housing:
1. Remove all compartment covers, and disconnect all cables and cords.
2. If liquid is leaking from any vent or hole, turn the phone so that the vent faces down. If not,
place the largest vent face down.
3. Let dry for at least 3 days. Check for liquid inside the phone before replacing compartment
covers & reconnecting cords.
ResettinG stations
If you have problems with the base, unplug it to reset it. Plug it back in after at least a minute.
If you have problems with a cordless handset or want to replace one, reset it:
#
1. Press & hold enD and at the same time until you see the System Reset menu.
2. If you still have the base the handset is registered to, select Deregister HS, then select the
handset you want to reset. If you don’t have that base anymore, select Base Unavailable
.
3. To confirm, select Yes. The handset displays Handset not registered
.
ReGisteRinG handsets
If Handset not registered displays on a handset, register the handset to a base before using it.
1. On the base, open the menu and select Register Accy
2. On the handset, press and hold until the handset displays Registering
.
#
.
3. Wait until the display says Registration Completed (about 30 seconds), then pick up the
HOMe/flasH.
#hifanydosuetd;opnre’tsshear a dial tone or the display says Registration Failed, charge the battery
completely, then try again.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 25
adaPteR and batteRY infoRmation
ComPlianCe infoRmation
aC adapter base
Charger
PS-0035
fCC PaRt 68 infoRmation
is equipment complies with Part 68 of the FCC
rules and the requirements adopted by the ACTA.
On the bottom of this equipment is a label that
contains, among other information, a product
identifier in the format US: AAAEQ##TXXXX.
If requested, this number must be provided to the
phone company.
Part number
PS-0034
Input voltage
120V AC, 60 Hz
7.8V AC @
8V AC @
300mA
Output voltage
450mA
x Use only the supplied AC adapters.
x Use the proper adapter for the base & any
chargers.
An applicable Universal Service Order Codes
(USOC) certification for the jacks used in
this equipment is provided (i.e., RJ11C) in the
packaging with each piece of approved terminal
equipment. A plug and jack used to connect this
equipment to the premises wiring and telephone
network must comply with the applicable FCC
Part 68 rules and requirements adopted by the
ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed
to be connected to a compatible modular jack that
is also compliant. See installation instructions
for details.
x Do not place the unit in direct sunlight or subject
it to high temperatures.
battery pack (with normal use)
Part number
Capacity
Talk time
Standby time
Battery life
BT-1025
400mAh, 2.4V DC
about 7 hours
about 7 days
about 1 year
e REN is used to determine the number of
devices that may be connected to a phone line.
Excessive RENs on a phone line may result in
devices not ringing in response to an incoming
call. In most but not all areas, the sum of RENs
should not exceed five (5.0). To be certain of the
number of devices that may be connected to a
line, as determined by the total RENs, contact the
telephone provider. e REN for this product is
part of the product identifier that has the format
US:AAAEQ##TXXXX. e digits represented by
## are the REN without a decimal point (e.g., 03
is a REN of 0.3).
If this equipment causes harm to the telephone
network, the telephone company will notify you
in advance that temporary discontinuance of
service may be required. But if advance notice
isn't practical, the telephone company will notify
the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the
FCC if you believe it is necessary. e telephone
company may make changes in its facilities,
equipment, operations or procedures that could
affect the operation of the equipment. If this hap-
pens the telephone company will provide advance
notice in order for you to make necessary modifi-
cations to maintain uninterrupted service.
Please follow instructions for repairing, if any
(e.g. battery replacement section); otherwise do
not substitute or repair any parts of the device
except as specified in this manual. Connection to
party line service is subject to state tariffs. Con-
tact the state public utility commission, public
service commission or corporation commission
for information. is equipment is hearing aid
compatible.
If you experience trouble with this equipment,
contact the manufacturer (see the cover of this
manual for contact information) or an authorized
agent. If the equipment is causing harm to the
telephone network, the telephone company may
x Replace the battery when the talk or standby time
becomes noticeably reduced. For replacements,
call the Parts Department (see the front cover).
x When the battery gets low, the handset beeps and
shows a low battery alert; put the handset in the
cradle for recharging.
ReChaRGeable batteRY waRninG
x is equipment contains a rechargeable Nickel-
Metal-Hydride (Ni-MH) battery.
x Nickel is a chemical known to the state of Califor-
nia to cause cancer.
x Do not short-circuit the battery.
x e batteries in this equipment may explode if
disposed of in a fire.
x Do not charge the batteries in any charger other
than the one specified in the owner's manual.
Using another charger may damage the battery or
cause it to explode.
As part of our commitment to protecting our
environment and conserving natural resources,
Uniden voluntarily participates in an RBRC®
industry program to collect and recycle used
Ni-MH batteries within the United States. Please
call 1-800-8-BATTERY for information on Ni-
MH battery recycling in your area. (RBRC® is a
registered trademark of the Rechargeable Battery
Recycling Corporation.)
Rechargeable batteries must be recycled or
disposed of properly.
warning! the cords on this product and/or
accessories contain lead, a chemical known
to the state of California to cause birth
defects or other reproductive harm. wash
hands after handling.
uniden works to reduce lead content in our
products & accessories.
Download from Www.Somanuals.com. All Manuals Search And Download.
26 - English
request that you disconnect the equipment until
the problem is resolved.
x e handset is designed for body-worn operation
and meets FCC RF exposure guidelines when
used with any belt clip, carrying case, or other
accessory supplied with this product. (All neces-
sary accessories are included in the package; any
additional or optional accessories are not required
for compliance with the guidelines.) ird party
accessories (unless approved by the manufacturer)
should be avoided as these might not comply with
FCC RF exposure guidelines.
If your home has wired alarm equipment con-
nected to a phone line, be sure that installing the
system does not disable your alarm equipment. If
you have questions about what will disable alarm
equipment, contact your telephone company or a
qualified installer.
Any changes or modifications to this product not
expressly approved by the manufacturer or other
party responsible for compliance could void your
authority to operate this product.
industRY Canada (i.C.) notiCe
TERMINAL EquIPMENT
NOTICE: According to telephone company
reports, AC electrical surges, typically resulting
from lightning strikes, are very destructive to
telephone equipment connected to AC power
sources. To minimize damage from these types of
surges, a surge arrestor is recommended.
NOTICE: is equipment meets the applicable
Industry Canada Terminal Equipment Technical
Specifications. is is confirmed by the registra-
tion number. e abbreviation IC before the
registration number signifies that registration was
performed based on a Declaration of Conformity
indicating that Industry Canada technical speci-
fications were met. It does not imply that Industry
Canada approved the equipment.
NOTICE: e Ringer Equivalence Number
(REN) for this terminal equipment is marked on
the equipment itself. e REN assigned to each
terminal equipment provides an indication of
the maximum number of terminals allowed to be
connected to a telephone interface. e termina-
tion on an interface may consist of any combina-
tion of devices subject only to the requirement
that the sum of the Ringer Equivalence Numbers
of all the devices does not exceed 5.
fCC PaRt 15 infoRmation
is device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions: (1) is device may not cause harmful
interference, and (2) is device must accept
any interference received, including interference
that may cause undesired operation. Privacy of
communications may not be ensured when using
this phone.
FCC PART 15.105(b): Note: is equipment has
been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15
of the FCC Rules. ese limits are designed to
provide reasonable protection against harmful
interference in a residential installation. is
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be deter-
mined by turning the equipment off and on, the
user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
RADIO EquIPMENT
e term IC before the radio certification number
only signifies that Industry Canada technical
specifications were met. Operation is subject to
the following two conditions: (1) this device may
not cause interference, and (2) this device must
accept any interference, including interference
that may cause undesired operation of the device.
"Privacy of communications may not be ensured
when using this telephone".
1-YeaR limited waRRantY
evidence of original purchase is required for
warranty service.
x Reorient or relocate the receiving antenna.
x Increase the separation between the equipment
and receiver.
WARRANTOR: UNIDEN AMERICA CORPO-
RATION ("Uniden")
x Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
ELEMENTS OF WARRANTY: Uniden warrants,
for one year, to the original retail owner, this
Uniden Product to be free from defects in materi-
als and craſtsmanship with only the limitations or
exclusions set out below.
x Consult the dealer or an experienced radio/TV
technician for help.
WARRANTY DURATION: is warranty to
the original user shall terminate and be of no
further effect 12 months aſter the date of original
retail sale. e warranty is invalid if the Product
is (A) damaged or not maintained as reasonable
or necessary, (B) modified, altered, or used
as part of any conversion kits, subassemblies,
or any configurations not sold by Uniden, (C)
improperly installed, (D) serviced or repaired
by someone other than an authorized Uniden
fCC Rf exPosuRe infoRmation
is product complies with FCC radiation expo-
sure limits under the following conditions:
x e base must be placed to allow a minimum of 20
cm (8 inches) between the antenna and all persons
during normal operation.
x e base must not be collocated or operated in
conjunction with any other antenna or transmit-
ter.
Download from Www.Somanuals.com. All Manuals Search And Download.
English - 27
service center for a defect or malfunction covered
by this warranty, (E) used in any conjunction
with equipment or parts or as part of any system
not manufactured by Uniden, or (F) installed or
programmed by anyone other than as detailed by
the owner's manual for this product.
Include evidence of original purchase and a note
describing the defect that has caused you to return
it. e Product should be shipped freight prepaid,
by traceable means, to warrantor at:
Uniden America Service
4700 Amon Carter Blvd.
Fort Worth, TX 76155
STATEMENT OF REMEDY: In the event that
the product does not conform to this warranty
at any time while this warranty is in effect, war-
rantor will either, at its option, repair or replace
the defective unit and return it to you without
charge for parts, service, or any other cost (except
shipping and handling) incurred by warrantor or
its representatives in connection with the perfor-
mance of this warranty. Warrantor, at its option,
may replace the unit with a new or refurbished
unit. THE LIMITED WARRANTY SET FORTH
ABOVE IS THE SOLE AND ENTIRE WARRAN-
TY PERTAINING TO THE PRODUCT AND
IS IN LIEU OF AND EXCLUDES ALL OTHER
WARRANTIES OF ANY NATURE WHATSO-
EVER, WHETHER EXPRESS, IMPLIED OR
ARISING BY OPERATION OF LAW, INCLUD-
ING, BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE. THIS
WARRANTY DOES NOT COVER OR PROVIDE
FOR THE REIMBURSEMENT OR PAYMENT
OF INCIDENTAL OR CONSEQUENTIAL DAM-
AGES. Some states do not allow this exclusion or
limitation of incidental or consequential damages
so the above limitation or exclusion may not
apply to you.
As an Energy Star
Uniden has determined that this
product meets the Energy Star
®
Partner,
®
guidelines for energy efficiency.
Energy Star
mark.
®
is a U.S. registered
x Uniden is a registered trademark of Uniden
®
America Corporation.
x e pictures in this manual are for example only.
Your phone may not look exactly like the pictures.
LEGAL REMEDIES: is warranty gives you
specific legal rights, and you may also have other
rights which vary from state to state. is war-
ranty is void outside the United States of America
and Canada.
PROCEDURE FOR OBTAINING PERFOR-
MANCE OF WARRANTY: If, aſter following
the instructions in the owner's manual you are
certain that the Product is defective, pack the
Product carefully (preferably in its original
packaging). Disconnect the battery from the
Product and separately secure the battery in its
own separate packaging within the shipping
carton. e Product should include all parts and
accessories originally packaged with the Product.
Download from Www.Somanuals.com. All Manuals Search And Download.
28 - English
|