GPS105
Operating Manual
&
Quick Start
Guide
GPS Transceiver
with an
Integrated
UHF Radio
To bring outstanding wireless communication products
to people's lives throughout the world.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Start
Guide
The Quick Start Guide pages are designed to allow you to install and operate your GPS105 as quickly as possible,
however it does not attempt to explain any of the advanced features of the GPS105 unit.
INSTALLING YOUR GPS105
Please consider the following before installing.
The GPS105 is designed to fit into a standard car stereo (DIN) fitting.
You may also use the supplied bracket & fasteners to mount the GPS105 in other locations.
The GPS105 uses a UHF antenna and a GPS internal antenna.
For a UHF antenna (not supplied) please follow the manufacturers instructions for installation.
It is recommended that the UHF and GPS antenna are mounted separately.
! If placing the GPS internal antenna on the dashboard or the rear parcel shelf then ensure the UHF antenna is
fitted towards the opposite end of the vehicle or fitted centre of the roof top.
!
!
The GPS105 runs on positive 13.8V DC, negative earth.
The positive wire is fused at 2 Amps.
With some vehicles, the window tint may prevent the GPS Internal Antenna from
acquiring a signal. In such a case, an optional External GPS antenna may be used.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
2
CONNECTING YOUR GPS105
EXTERNAL SPEAKER JACK
BACK PANEL
UHF ANTENNA CONNECTOR
GPS ANTENNA CONNECTOR
DC POWER CORD
Microphone Socket
i. Remove fuse from fuse holder along power lead.
ii. Connect 13.8V supply to the power lead making sure positive is applied to the red wire and
ground to the black wire.
iii. Connect the UHF Antenna with PL259 fitting (not included).
iv. Connect the GPS Internal Antenna.
v. Make sure the Power Switch knob is OFF (see Controls page 4).
vi. Re-insert the fuse into the fuse holder.
vii. Connect microphone plug to microphone socket.
An optional External Speaker may be connected via the External Speaker Jack. When the
external speaker is connected the internal speaker is automatically disconnected.
The connecting wire must use a 3.5mm miniature plug.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
3
TEST FOR A GPS SIGNAL
i. Turn the GPS105 ON.
ii. The Welcome display will appear.
SEARCHING FOR
INSTANT
iii. After 3 seconds the initial display will switch to the UHF-CB display.
iv. At the top of the display the unit will indicate it is searching for satellite information.
Make sure the GPS antenna has an unobstructed view of the sky.
For the initial power up it may take up to 15 minutes to secure satellite information.
When satellite data has been retrieved 'SEARCHING FOR SATELLITE' will disappear and
'GPS' will show at the top of the display.
If the unit continues to indicate searching for satellite beyond 15 minutes try holding
the GPS Internal Antenna outside of the vehicle. If satellite data is then retrieved and
'GPS' appears then the vehicle windscreen may have a tint which interferes with the
GPS signal. An optional External GPS Antenna may be fitted.
In this case an external GPS Antenna may be used in place of the internal antenna.
v. Turn OFF the unit and replace the GPS antenna if required and repeat steps i to iv.
vi. Secure all fittings.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
4
SETTING USER NAME
You may personalize your GPS105 by setting a User name which will appear at the top of the display. The User name
also forms part of your call ID when communicating to radios using similar technology (GPS105 or GPS205) on
channel 22 or 23.
To set your Username:
MENU
i. Press & hold
to bring up the menu list.
ii. Press
iii. Press
and scroll down until USER NAME is highlighted.
ENT
.
iv. Enter Name:
Press
Press
or
or
to select desired character.
to move to previous or next character.
ENT
v. Press
to confirm.
!
!
Username cannot include blank spaces.
The user name may be up to 12 characters long.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
5
SEND POSITION ON
The SEND POSITION function enables the GPS105 to transmit your User name and position on channels 22 and 23.
The factory setting for this feature is OFF.
Current regulations permit enabling the SEND POSITION function to operate on Channels
22 and 23 only. The SEND POSITION will be OFF from the factory.
To turn SEND POSITION ON:
MENU
i. Press & hold
ii. Scroll
iii. Press
to bring up the menu list.
to highlight SENDPOSITION.
ENT
.
iv. Press
v. Press
to select ON.
to confirm setting.
ENT
End of
Quick Start
Guide
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Warnings & Notifications...................................................................................................................................................i
Quick Start Guide.............................................................................................................................................................ii
Installing Your GPS105..................................................................................................................................ii
Connecting Your GPS105..............................................................................................................................iii
Test For A GPS Signal.....................................................................................................................................iv
SettingUserName..........................................................................................................................................v
Send Position ON..........................................................................................................................................vi
Contents..........................................................................................................................................................................1
Introduction....................................................................................................................................................................3
Features...........................................................................................................................................................................3
Controls...........................................................................................................................................................................4
Indicators........................................................................................................................................................................5
Included With Your GPS105.............................................................................................................................................6
UHF-CB Operation...........................................................................................................................................................7
Setting The Squelch.......................................................................................................................................7
Selecting A Channel.......................................................................................................................................8
To Transmit And Receive................................................................................................................................8
To Operate In Duplex Mode (Repeaters)........................................................................................................9
ScanningwithPriorityChannel....................................................................................................................10
Scanning-ScanMemory..............................................................................................................................10
Reply Delay..................................................................................................................................................10
Instant Channel..........................................................................................................................................11
CTCSS (Continuous Tone Coded Squelch System)......................................................................................11
BCLO (Busy Channel Lock Out) Feature......................................................................................................11
Key Beep ON/OFF.........................................................................................................................................12
Roger Beep..................................................................................................................................................12
1
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
GPS Operation...........................................................................................................................................................13
Speed Warning............................................................................................................................................13
EarlyWarningSafetyAlerts...........................................................................................................................14
Warning Volume..........................................................................................................................................14
Caller Display...............................................................................................................................................15
CALLER ID Memories...................................................................................................................15
ToStoreTheCallerIntoMYPOI.....................................................................................................15
Mark Location.............................................................................................................................................16
QuickAccessLocations.................................................................................................................16
MYPOILocations..........................................................................................................................17
Edit/Delete MY POI.......................................................................................................................18
AddOrDeleteSafetyAlert..............................................................................................................19
Navigation...................................................................................................................................................20
NavigateToQuickAccess...............................................................................................................21
Navigate To CALLER.....................................................................................................................21
Navigate To MY POI.......................................................................................................................22
Navigate To STATE/CITY.................................................................................................................23
TRIP Computer............................................................................................................................................24
To Reset TRIP Computer..............................................................................................................................24
My Position..................................................................................................................................................25
LCD Contrast...............................................................................................................................................25
UHF Channels & Frequencies....................................................................................................................................26
CTCSS Tone List.........................................................................................................................................................26
Troubleshooting........................................................................................................................................................27
Warranty....................................................................................................................................................................28
2
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The Uniden GPS105 is designed to provide you with years of trouble free service. It's rugged components and
materials are capable of withstanding harsh environments.
We are certain that you will enjoy your GPS105. Please read this operating Manual carefully to ensure you gain the
optimum performance of the unit.
FEATURES
Backlit LCD Display
Key Beep ON/OFF
!
!
GPS FUNCTIONS
!
!
!
!
!
!
!
!
Navigation to pre-programmed Australian and New Zealand cities and suburbs
Mark and delete up to 500 of your own locations
Fixed Speed Camera Warning
Red Light Camera Warning
Black Spot Warning
My Position Display
20 Caller ID Memories*
Trip Computer
UHF-CB
!
!
!
!
!
!
!
!
!
Transmit & Receive on 40 UHF channels
Duplex capability
Scan with Priority CH Watch
Scan Memory ON/OFF
Roger Beep ON/OFF
BCLO (Busy Channel Lock Out) Function
Send, Receive and Navigate your Position with GPS CALLER ID*
38 Built in CTCSS (Continuous Tone Coded Squelch System) Codes
Selectable INSTANT Channel
* To benefit from these features, transmission needs to be with another compatible Uniden GPS product
(GPS105 or GPS205) on channel 22 or 23.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
6
5
GPS105
3
1
4
2
10
7
8
9
1. LCD Display
SCAN
2.
3.
/MEM - Scan Key/Memory Key
NAVI
- Navigation Key
4. VOL/SQ - Centre Knob (Power-VOLUME): Turns the Power ON/OFF and adjusts the Volume.
Outer Ring (SQUELCH): Adjusts the Squelch
5. PTT - Push to Talk(PTT) switch
6. Channel Instant - Instant Channel switch
7. Speaker
DISP
8.
9.
/MENU/ - Display key/ Menu key/ Back to previous Display key
/MARK/ - Enter key/ Mark key/ Move to next Display key
up, down, left, right keys or
ENT
10. SCROLL -
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICATORS
12 13
11
20
14
15
16
17
18
19
UHF-CB Display
11 GPS - GPS status icon
16 MEMORY icon
17 CTCSS icon
18 SCAN icon
12 USER NAME - An example (MICHAEL) is shown
13 BUSY - Receive icon
19 CTCSS Channel indicator
20 Channel indicator
14 INSTANT - Channel Instant icon
15 DUPLEX icon
5
Download from Www.Somanuals.com. All Manuals Search And Download.
INCLUDED WITH YOUR GPS105
GPS105 Owners Manual
Microphone
Mounting Bracket, Knobs,
Rubber washer, Washer Stars
and Screws.
Microphone Hanger Screws
and washers
DC Power Cord with fuse
GPS Internal Antenna
If any of these items are missing from the box, contact your dealer immediately.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CB - OPERATION
All UHF-CB functions are only available when in UHF-CB mode.
SETTING THE SQUELCH
1. To turn the unit ON, rotate VOL knob clockwise. Adjust volume to a comfortable level.
2. Think of the Squelch control as a gate. If you turn SQUELCH
fully clockwise it raises the "Squelch Gate" so
that no signals get through.
3. If you turn the SQUELCH fully counter clockwise, it lowers the
"Squelch Gate" so that everything gets through - noise,
weak signals and strong signals.
4. To set the "Squelch Gate" to the desired level, turn SQUELCH
counter clockwise until you hear noise. Then turn the SQUELCH
clockwise just until the noise stops. Now only strong and medium
signals get through.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CB - OPERATION
SELECTING A CHANNEL
The GPS 105 uses the 40 UHF-CB Channels. For your reference a list of the available channels and corresponding
frequencies is printed on page 26.
To select a desired channel in UHF-CB Mode:
1. Press
or
momentarily to step up or down a channel.
or to rapidly step up or down channels.
2. Press and hold
TO TRANSMIT AND RECEIVE
1. Before you transmit, listen for activity on the selected channel.
2. When the channel is clear, press and hold the PTT to transmit.
‘TX’ will flash on the LCD.
3. Hold the microphone approximately 5 cm in front of your mouth.
Speak in a clear, normal conversational voice.
4. When you have finished speaking, release the PTT and listen for a response. 'TX' then disappears on the LCD.
While receiving, the 'BUSY' icon will flash on the display.
Transmit will not occur if: The unit detects that the channel is busy when using the
CTCSS function with BCLO (page11).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CB - OPERATION
TO OPERATE IN DUPLEX MODE (REPEATERS)
The Duplex function enables you to access local repeater stations. You can only activate Duplex from CH01-CH08.
UHF CB Repeaters are used to retransmit or relay your signal.
Repeaters will extend the range of your radio and overcome the shielding effect caused by solid obstructions.
Contact a retailer for a list of repeaters available in your area.
Operation with the aid of a Repeater
To turn DUPLEX ON/OFF:
1. Select the channel of the repeater in your area (CH01 - CH08).
MENU
2. Press & hold
.
3. Scroll
4. Press
5. Press
6. Press
to highlight DUPLEX.
ENT
.
or
to select ON or OFF as desired.
ENT
to confirm selection.
'DUPLEX' will appear when a duplex channel is used only if duplex is turned ON.
If DUPLEX is selected from the MENU options when the channel is not from
CH01 - CH08, an error tone sounds.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CB - OPERATION
SCANNING with PRIORITY CHANNEL
The scan function scans channels that are in the scan memory and stops at an active channel. Whichever channel
you have selected when SCAN begins becomes the Priority Channel. SCAN will check the priority channel every 1.5
seconds.
To initiate scanning:
1. Press
SCAN
momentarily to begin scanning. The SCAN icon flashes on the display.
2. Press PTT, INSTANT or any function key to cancel SCAN.
If SCAN is cancelled while stopped on a busy channel that channel will be the exit channel.
If SCAN is cancelled while scanning then the unit will exit to the priority channel which is the current channel when
SCAN is turned ON.
SCANNING - SCAN MEMORY
You can only scan channels which are currently in the scan memory. By default all channels are active in the scan
memory.
To add or remove channels from the scan memory:
1. Select a channel using scroll
or
.
MEM
2. Press and hold
.
REPLY DELAY
While scanning, the GPS105 stops at a busy channel and receives a transmission.
When the received signal is over, the unit will wait for 3 seconds for the return of the signal, otherwise the radio
resumes scanning.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CB - OPERATION
INSTANT CHANNEL
The Instant Channel feature enables a chosen channel to be called at the press of a button. Only one channel at a
time is designated as the Instant Channel.
To register or change the Instant channel:
1. Select a channel using scroll
or
.
2. Press and hold the Instant Channel button. 'INSTANT' will appear on the UHF-CB display for the channel
selected.
To use Instant Channel:
Press the Instant Channel button momentarily when in the UHF-CB mode to instantly change to the Instant channel
and that channel will be automatically called.
CTCSS (Continuous Tone Coded Squelch System)
CTCSS is a feature that allows a group to talk to each other without hearing other users on the same channel.
To activate CTCSS on a current channel:
MENU
1. Press & hold
.
2. Scroll
3. Press
to highlight CTCSS.
ENT
.
The CTCSS Tone will appear for the current channel.
4. USE
or
to select desired CTCSS tone.
ENT
5. Press
to confirm.
Channels 5 and 35 are used as emergency channels. CTCSS will not operate on these
channels.
BCLO (Busy Channel Lock Out) Feature
The BCLO feature functions automatically when using a channel with CTCSS ON. If attempting to transmit on a
channel with CTCSS ON and that channel is busy the BCLO feature will prevent transmission until the channel
becomes clear.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CB - OPERATION
KEY BEEP ON/OFF
Your radio emits a beep each time one of the keys (except for the PTT button) is pressed.
To turn Key Beep ON/OFF:
MENU
1. Press & hold
2. Scroll
.
to highlight KEY BEEP.
3. Press
4. Press
5. Press
ENT
.
or
to select ON or OFF.
ENT
to confirm.
ROGER BEEP
Roger Beep is a BEEP that is sent to notify the end of transmission.
Roger Beep can be heard through the speaker when Key Beep is on. Roger Beep is transmitted even if Key Beep is
turned off. However, Roger Beep will not be heard from the speaker.
To turn Roger Beep ON/OFF:
MENU
1. Press & hold
2. Scroll
ENT
.
to highlight ROGERBEEP.
3. Press
4. Press
5. Press
.
or
to select ON or OFF.
ENT
to confirm.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
GPS OPERATION
The GPS antenna must have an unobstructed view of the sky for the GPS105 to retrieve satellite data which is used for
the GPS features described on pages 13 to 25.
Current regulations permit the SEND POSITION to operate on Channels 22 and 23 only.
To comply with current regulations, Uniden recommends not to transmit data more than
10 times within an hour on channels 22 and 23.
SPEED WARNING
OPERATION FLOW
Press & hold
ENT
ENT
SPEEDWARNING
MENU
If the current speed that the GPS105 is moving at exceeds the SPEEDWARNING alert setting then a warning tone will
sound and this POP UP Speed Alert will show. The current speed will be indicated. The display remains until the
moving speed falls below the Alert Setting.
Press
DISP
to cancel the alert.
To set a moving speed warning limit:
MENU
1. Press & hold
to bring up the menu list.
2. Scroll
3. Press
4. Press
5. Press
to highlight SPEEDWARNING.
ENT
.
to adjust speed warning to desired level.
to confirm.
ENT
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EARLY WARNING SAFETY ALERTS
The GPS105 has a preprogrammed memory that will alert you of Fixed Speed Camera, Red Light Camera or Black
Spot. These displays automatically pop up and an alert tone sounds when approaching within 400m and 160m of the
alert location.
Press
DISP
to cancel the alert.
FIXED SPEED CAMERA
RED LIGHT CAMERA
BLACK SPOT
160m
400m
Camera
WARNING VOLUME
OPERATION FLOW
Press & hold
ENT
WARNING VOL
ENT
MENU
To set the volume for the safety alerts (FIXED CAMERA, RED CAMERA, BLACK SPOT & SPEED WARNING) with this
function:
MENU
1. Press & hold
to bring up menu list.
2. Scroll
3. Press
4. Press
5. Press
to highlight WARNING VOL.
ENT
.
to adjust volume setting (8 levels:0-7, 0 is OFF).
to confirm.
ENT
Download from Www.Somanuals.com. All Manuals Search And Download.
CALLER DISPLAY
The caller display information received from another radio using similar technology
onchannels22and23willPOPUPattheendofareceivedtransmission.
GPS
GPS
Theinformationincludes:
! Callers USER NAME.
! Distancetowherecallwastransmittedfrom.
! Estimated time of arrival from your location to position of caller calculated at your
averagemovingspeed.
For compass heading & distances to appear the
GPS105 requires a moving direction. If '?'
appearsonthedisplaypleasemoveforwardtoobtain
direction.
?
CALLERIDMemories
___m
TheGPS105automaticallystoresCALLERIDdata.Itwillstoreupto20setsof the
username,lastreceivedGPSpositionandtheday/montharestored.
Once20Callersarestoredtheoldestdataisdroppedfromthelistwhennewcallersareadded.
A caller's user name is stored in the caller list only once. If the caller calls again their
information is updated, not repeated.
ThePOPUPCALLERwillremainfor10secondsandthenreturntothepreviousdisplay.
IfyouwishtokeepthePOPUPCALLERDISPLAYonthescreenforlonger thenwithinthe10secondperiodpress
TonavigatetoCALLERseepage21.
ENT
.
ToStoretheCallerintoMYPOI
Ifyouwishtostorethecaller'sinformationasaMYPOI(mypointofinteresttonavigatebacktoinfuture)then:
WhilethePOPUPCALLERDISPLAYshows:
ENT
1. Press
2. Press
3. Press
twotimeswithin1second.
toselectYES.
toconfirm.
ENT
TonavigatetoMYPOIseepage22.
If you save the information from a caller already stored in MY POI then the information is
updatedandnotrepeated.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MARK LOCATION
Mark Location is used to store in memory a location, which may be used in future as a point to navigate back to, or
safety alert location.
QUICK ACCESS LOCATIONS
The quick access locations are to mark your HOME, OFFICE, HOTEL, AIRPORT or BOATRAMP locations. You may
mark the location with the current GPS coordinates or adjust the coordinates to suit.
OPERATION FLOW
Example
Example
PRESS & HOLD
°
HOME
ENT
ENT
MRK
°
1. Move the GPS105 to the location you wish to mark, or have the desired
coordinates at hand.
2. Press and hold
MRK
.
3. Scroll
to highlight desired quick access name.
ENT
4. Press
.
The quick access display appears with the quick access name and the current GPS coordinates:
If no GPS is available the last GPS position appears.
5. You may change the longitude & latitude values by pressing
to change the value.
to move the cursor and pressing
ENT
6. Press
to confirm.
! The longitude and latitude coordinates must be valid coordinates in the South
Pacific Area.
! The coordinates are displayed in WGS-84 data format.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
MY POI LOCATIONS
You may mark up to 500 locations into MY POI (My Point Of Interest). Each location may be personalised with a
name.
OPERATION FLOW
PRESS & HOLD
MY POI
ENT
ADD
MRK
Example
Choose
name/
coordinates
ENT
ENT
0001_____
1. Move the GPS105 to the location you wish to mark as MY POI, or have the desired coordinates at hand.
MRK
2. Press and hold
to bring up the mark location list.
3. Scroll
to highlight MY POI.
ENT
4. Press
5. Scroll
6. Press
.
.
to highlight ADD.
ENT
7. MY POI display appears with the next available memory number and the current coordinates.
You can move the cursor by pressing
pressing or
or
and can adjust the name and coordinate readings by
.
CAMP
ENT
8. When satisfied with the name and coordinates press
to confirm.
! If the name already exists or the coordinates are invalid an error message
will appear.
! The longitude and latitude coordinates must be valid coordinates in the
South Pacific Area.
! Coordinates are displayed in WGS84 data format.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EDIT/DELETE MY POI
OPERATION FLOW
PRESS & HOLD
ENT
ENT
MY POI
EDIT
MRK
Example
Example
BOB_______
AAAAAAAAAAAAAA
ENT
ENT
1. Press and hold
MRK
to bring up Mark Location List.
2. Scroll
3. Press
4. Scroll
5. Press
to highlight MY POI.
ENT
.
.
to highlight EDIT or DELETE.
ENT
6. The EDIT or DELETE MY POI name list appears in Alpha-numeric order.
To find a name you may scroll . To shortcut to the capital letter of the name press
to highlight
to move back
the capital letter on the right of the display. Then scroll
to the name list.
to the desired letter. Press
ENT
7. Press
to confirm name selection.
8. If you have chosen EDIT you may use the
If you have chosen DELETE the delete confirmation display appears. Press
buttons to edit the name and the coordinates.
to select delete YES or NO.
ENT
9. When satisfied with the edit or ready to delete, press
to confirm.
If a key is not pressed within 60 seconds Edit/Delete MY POI is cancelled.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ADD or DELETE SAFETY ALERT
You can store into memory new safety alert (Fixed Speed Camera, Red Light Camera or Black Spot) locations.
If the GPS105 is within 400m of a stored Safety Alert or OPTION location then you can delete this from memory.
The OPTION feature is currently unavailable but may in future be pre-programmed with
points of interest.
OPERATION FLOW
PRESS & HOLD
Example
Example
ADD
ENT
RED CAMERA
MRK
Example
°
ENT
ENT
°
1. Move the GPS105 to an alert location you wish to add or delete.
MRK
2. Press and hold
to bring up Mark Location List.
3. Scroll
to highlight SPEED CAMERA or RED CAMERA or BLACK SPOT or OPTION.
ENT
4. Press
5. Scroll
6. Press
.
to highlight ADD or DELETE.
ENT
.
7. When ADD is selected your current GPS location is displayed. You may edit the coordinates using the scroll
buttons.
When DELETE is selected press
or
to select delete YES or NO.
ENT
8. When ready, press
to confirm.
If a key is not pressed within 60 seconds Add or Delete Safety Alert is cancelled.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
NAVIGATION
The navigation feature allows you to select a desired stored location point to navigate to. The location point can be a
pre-installed state, city or suburb, quick access location, MY POI or CALLER from the caller list.
When navigating to a location point the navigation or NAVI Display alternates as follows:
5 Seconds Later
SUZAN
GPS
SUZAN
GPS
N
E
S
N
E
S
5 Seconds Later
W
W
DISTANCE
TIME TO GO
14.7km
16hr22min
If PTT is pressed the UHF-CB Display will appear. When transmission is complete the display will return to NAVI
Display after 5 secs.
When approaching within 160m and 20m of the set destination the NAVI ARRIVE Tone will sound.
The compass heading (directional pointer) is referenced to the GPS105's last
forward movement.
When viewing the compass heading the GPS105 must be facing in the
direction of the last forward movement in order to read the compass heading
correctly.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to Quick Access
OPERATION FLOW
Example
PRESS
OFFICE
ENT
NAVI
NAVI
1. Press
2. Scroll
3. Press
.
to highlight desired Quick Access Name.
. NAVI display appears.
to switch between UHF-CB, NAVI & TRIP COMPUTER displays.
ENT
DISP
Press
ENT
NAVI
To Cancel Navigation press
then press
.
Navigate to CALLER
OPERATION FLOW
Example
PRESS
ENT
CALLER
SUZAN
ENT
NAVI
NAVI
1. Press
2. Scroll
3. Press
4. Scroll
5. Press
.
.
to highlight CALLER.
to desired caller.
ENT
ENT
. NAVI display appears.
DISP
Press
to switch between UHF-CB, NAVI & TRIP COMPUTER displays.
NAVI
ENT
To Cancel Navigation press
then press
.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to MY POI
OPERATION FLOW
PRESS
MY POI
Example
ENT
PARK
ENT
NAVI
NAVI
1. Press
.
2. Scroll
3. Press
4. Scroll
to highlight MY POI.
ENT
.
to find a desired name.
To shortcut to the capital letter of the name:
Press
Scroll
Press
to highlight the capital letter on the right of the display.
to the desired letter.
to move back to the name list.
ENT
5. Press
. NAVI display appears.
DISP
Press
to switch between UHF-CB, NAVI & TRIP COMPUTER displays.
NAVI
ENT
To Cancel Navigation press
then press
.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Navigate to STATE/CITY
OPERATION FLOW
Example
PRESS
ENT
STATE/CITY
NSW
NAVI
Example
ENT
ENT
ACACIA PK
NAVI
1. Press
2. Scroll
3. Press
.
to highlight STATE/CITY.
ENT
.
The list of Australian States and NZ appears.
4. Scroll
to desired state.
ENT
5. Press
6. Scroll
. The City/Suburb list appears.
to desired City or suburb.
To shortcut to the capital letter of the name:
Press
Scroll
Press
to highlight the capital letter on the right of the display.
to the desired letter.
to move back to the name list.
ENT
7. Press
. NAVI display appears.
DISP
Press
to switch between UHF-CB, NAVI & TRIP COMPUTER displays.
NAVI
ENT
To Cancel Navigation press
then press
.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TRIP COMPUTER
The GPS105 can indicate COMPASS heading and the present speed, average speed, maximum speed and the distance
travelled through the TRIP COMPUTER.
DISP
Press
to switch between UHF-CB, NAVI (if navigating) & TRIP COMPUTER displays.
The TRIP displays alternate automatically as follows:
After 5 sec
TRIP
GPS
TRIP
GPS
TRIP
GPS
SPEED k
SPEED k
SPEED k
k
k
h
k
N
W
E
S
N
E
S
N
W
E
S
h
h
AVG SPD
MAX SPD
DIST
k
k
k
h
k
W
72h
99999km
SPEED, AVG SPD DISPLAY
DIRECTION
SPEED, MAX SPD DISPLAY
DIRECTION
SPEED, DIST DISPLAY
DIRECTION
After 5 sec
After 5 sec
TO RESET TRIP COMPUTER
OPERATION FLOW
Press & hold
ENT
ENT
TRIP RESET
MENU
MENU
1. Press & hold
2. Scroll
ENT
to bring up menu list.
to highlight TRIP RESET.
3. Press
4. Press
5. Press
.
or
to select YES.
ENT
to confirm.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
MY POSITION
OPERATION FLOW
Press & hold
ENT
MY POSITION
MENU
Your current GPS coordinates can be viewed with this
selection.
MENU
1. Press & hold
to bring up the menu list.
MY POSITION appears as the first highlighted selection.
ENT
2. Press
to confirm selection.
My Position display appears with your current GPS coordinates.
ENT
DISP
3. Press
or
to exit.
coordinates are displayed in WGS84 format.
LCD CONTRAST
OPERATION FLOW
Press & hold
ENT
ENT
LCD CONTRAST
MENU
MENU
1. Press & hold
to bring up the menu list.
2. Scroll
to highlight LCD CONTRAST.
ENT
3. Press
4. Press
5. Press
.
to adjust contrast level (8 levels 0-7).
ENT
to confirm.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
UHF CHANNELS & FREQUENCIES
Simplex Mode
Transmit / Receive
Frequency (MHz)
Simplex Mode
Transmit / Receive
Duplex Mode
Transmit
Frequency (MHz) Frequency (MHz)
CH
CH
No.
No.
476.925
476.950
476.975
477.000
477.025
477.050
477.075
477.100
477.125
477.150
477.175
477.200
477.225
477.250
477.275
477.300
477.325
477.350
477.375
477.400
476.425
476.450
476.475
476.500
476.525
476.550
476.575
476.600
476.625
476.650
476.675
476.700
476.725
476.750
476.775
476.800
476.825
476.850
476.875
476.900
477.175 CH31
477.200 CH32
477.225 CH33
477.250 CH34
477.275 CH35
477.300 CH36
477.325 CH37
477.350 CH38
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Channels 05 and 35 are Emergency Channels and Channel 11 is a Calling
Channel. Channels 22 and 23 are used for telemetry and telecommand
applications, voice communications are not permitted on these channels.
CTCSS TONE LIST
Code No.
Freq. (Hz)
Code No.
Freq. (Hz)
Code No.
Freq. (Hz)
00("oF")
01
02
03
04
05
06
07
08
09
10
11
12
OFF
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
13
14
15
16
17
18
19
20
21
22
23
24
25
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
26
27
28
29
30
31
32
33
34
35
36
37
38
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
If your GPS105 does not perform to your expectations, try the suggestions listed below.
Unit does not operate. ! Check the 2 Amp fuse in the power lead.
No GPS Detection.
! Make sure the GPS antenna has an
unobstructed view of the sky.
Cannot send or
receive Caller ID.
! Make sure you are communicating with a
compatible unit on channels 22 or 23.
! Check that SEND POSITION is set to ON
(Quick Start Guide step 5).
Does not operate in
Duplex mode.
! Make sure you select channels 1-8 for
Duplex operation.
! Check that you are within range of a local
repeater station.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
UNIDEN GPS105 UHF CB RADIO WITH GPS
Limited One Year Warranty
Please keep your sales docket as it provides evidence of warranty.
Warrantor: Uniden Australia Pty Limited ABN 58 001 865 498
Uniden New Zealand Limited
Warranty only available in original country of purchase
Elements of Warranty: Uniden warrants to the original retail owner for the duration of this warranty, its GPS105
UHF CB Transceiver Radio with GPS (hereinafter referred to as the Product) to be free from defects in materials and
craftsmanship with only the limitations or exclusions set out below.
Warranty Duration: This warranty to the original retail owner only, shall terminate and be of no further effect ONE
(1) Year after the date of original retail sale. This warranty will be deemed invalid if the Product is; (A) Damaged or
not maintained as reasonable and necessary, (B) Modified, altered or used as part of any conversion kits,
subassemblies, or any configurations not sold by Uniden, (C) Improperly installed, (D) Repaired by someone other
than an authorised Uniden Repair Agent for a defect or malfunction covered by this warranty, (E) Used in conjunction
with any equipment or parts or as part of a system not manufactured by Uniden, (F) Installed, programmed or
serviced by anyone other than an authorised Uniden Repair Agent, or (G) Where the Serial Number label of the
product has been removed or damaged beyond recognition.
Parts Covered: This warranty covers for 1 year, the UHF CB Transceiver. Accessories: Internal GPS Antenna,
microphone etc is covered for 90 days.
Statement of Remedy: In the event that the product does not conform to this warranty at any time while this
warranty is in effect, the warrantor at its discretion, will repair the defect or replace the product and return it to you
without charge for parts and service. This warranty does not cover provide for the reimbursement or payment of
incidental or consequential damages.
THIS GUARANTEE IS IN ADDITION TO AND DOES NOT IN ANY WAY AFFECT YOUR RIGHTS UNDER THE CONSUMER
GUARANTEE ACT.
Procedure for Obtaining Performance or Warranty: In the event that the Product does not conform to this
warranty, the Product should be shipped or delivered, freight prepaid, with evidence of original purchase, (eg. a copy
of the sales docket), to the warrantor at:
UNIDEN AUSTRALIA PTY LIMITED UNIDEN NEW ZEALAND LIMITED
Service Division
Service Division
345 Princes Highway,
Rockdale, NSW 2216
Fax (02) 9599 3278
www.uniden.com.au
150 Harris Road,
East Tamaki, Auckland
Fax (09) 274 4253
www.uniden.co.nz
Customers in other states should ship or deliver the Product freight pre-paid to the nearest Uniden Authorised Repair
Centre. (Contact Uniden for the Warranty Agent nearest you.)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|