Digital Spread
Spectrum Provides
Long Range, Clear
Sound, and Secure
Communication
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for choosing the Uniden EXS 2050 cordless telephone.
This phone is designed for reliability, long life, and outstanding
performance utilizing the latest 900 MHz Spread Spectrum
technology.
Note: Some illustrations in this manual may differ from the
actual unit for explanation purposes.
Features
• 900 MHz Spread Spectrum Technology
• Digital Answering Device
• 10 Memory Dial Locations
• 32 Digit Redial
• Flash and Pause
• Redial
• Pulse / Tone Dialing
• Page
• 6 Hour Talk Time
• 10 Day Standby Battery Time
• Handset Earpiece and Ringer Volume Control
• Hearing Aid Compatible
• Headset Compatible
Digital Spread Spectrum Technology utilizes a “wider
frequency band” vs. a “single narrow band” used in standard
digital transmissions. The result is a more secure conversation
with the clarity of digital sound, extended range, and minimal
interference from other cordless phones.
Random Code™ digital security automatically selects one of
over 65,000 codes for the handset and base.
These features enhance your phone’s security and prevent
unauthorized calls as a result of your phone being activated
by other equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and functions
1
2
5
6
7
talk
batt
DIGITAL SPREAD SPECTRUM
13
14
15
vol
talk
flash
8
9
mute
mem
rdlal
abc
def
1
2
3
16
ghi
jkl
mno
4
7
5
8
0
6
9
#
pqrs
tuv
wxyz
oper
3
4
10
11
12
17
18
channel
pause
tone
ringer
19
DIGITAL SPREAD SPECTRUM
21
22
23
speaker
24
25
26
35
volume
status
36
37
delete
play/stop
38
39
27
28
repeat
greeting voice memo
skip
40
answer on/off pin
clock
page
29
mic
20
30
31 32 33 34
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Handset antenna
2. Headset jack cover
3. Handset battery compartment
4. Ringer on/off switch
5. Handset speaker
6. Talk/Batt LED
7. Talk key
20. Base microphone
21. Base speaker
22. Speaker key
23. Handset retainer clip
24. Speaker LED
25. Volume down key
26. Status LED
8. Volume down key
9. Mute key
27. Delete key
28. Repeat key
10. Channel key
29. Greeting key
11. Pause key
30. Base charge contacts
31. Answer on/off key
32. Pin code key
33. Clock key
12. Handset microphone
13. Volume up key
14. Flash key
15. Redial key
34. Page key
16. Memory key
17. Ringer key
18. Tone key
35. Base antenna
36. Volume up key
37. LED display
19. Handset charge contacts
38. Play/Stop key
39. Skip key
40. Voice memo record key
41. Record time switch
42. Ring time switch
43. Base ringer switch
44. Pulse-Tone switch
45. DC power input
46. Tel line jack
AN4/1
41
42
RCTIME
24/TS
RNGTIME
43 44 45 46
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Basics
Contents
Introduction / Features...............inside front cover
Controls and Functions ..............inside front cover
Getting Started
Read this first..........................................................3
Step 1: Checking the package contents...............4
Step 2: Setting up the base unit ...........................5
Mounting the base unit on a wall ...........8
Step 3: Installing the handset battery pack........10
Memory Dialing
Basics
Making a call........................................................12
Receiving a call ....................................................13
Ringer mute ..........................................................13
Adjusting the volume...........................................14
Flash and Call Waiting .........................................15
Redialing a call.....................................................15
Mute ......................................................................15
Traveling out-of-range..........................................16
Using the page feature.........................................16
3-way
Conference
Features
Integrated
Answering
Device
Memory Dialing
Storing phone numbers .......................................17
Making calls with memory dialing......................18
Chain dialing.........................................................18
Erasing a stored phone number..........................19
Additional
Information
3-way Conference Features
3-way conferencing..............................................20
Troubleshooting
Index
Integrated Answering Device
Features.................................................................21
Setting up your answering system......................22
Using your answering system .............................26
Additional Information
Changing the digital security code......................32
Installing the beltclip............................................33
Headset installation..............................................33
Note on power sources .......................................34
Maintenance..........................................................34
Troubleshooting..................................................35
Index .....................................................................38
Download from Www.Somanuals.com. All Manuals Search And Download.
Read this first
This cordless telephone must be set up before use. Follow these steps;
Step 1
(page 4)
Unpack and check the telephone and accessories.
Step 2
(page 5 to 9)
Next, choose the best location to set
up the base unit.
Base unit
Step 3
(page 10 to 11)
Then, insert the battery pack into the handset.
You have to charge the battery pack for 15-20
hours before using the phone.
Handset
About the digital security code
This cordless telephone uses a digital security code to prevent
unauthorized access to your base unit. This security code prevents
other cordless handsets from making calls through your base unit.
A random security code will be assigned automatically between
your base unit and handset when you charge the battery pack for
the first time.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking the package contents
Make sure you have received the following items in the package.
If any of these items are missing or damaged, contact the Uniden
Parts Department (see below).
• Base unit
• Handset
• AC adapter (AD-420)
• Rechargeable
battery pack
(BT-905)
• Telephone line
cord (Long, Short)
• Wall mount adapter
• Beltclip
• Memo sticker
• This Owner's Manual
• Precautions and Important Safety Instructions
• Registration Card
Uniden Parts Department
(800) 554-3988
Hours: M-F 8:30 AM to 5:00 PM CST.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up the base unit
Do the following steps.
• Choose the best location
• Connect the base unit
• Choose the dialing mode
Choose the best location
Before choosing a location for your new phone, read the
INSTALLATION CONSIDERATIONS included in the PRECAUTIONS
AND IMPORTANT SAFETY INSTRUCTIONS brochure. Here are some
important guidelines you should consider:
Avoid heat sources, such as
radiators, air ducts, and sunlight
Avoid noise sources such as a window
by a street with heavy traffic
Avoid microwave ovens
Avoid television sets
and other electronic
equipment
Avoid excessive
moisture, extremely low
temperatures, dust,
mechanical vibration, or
shock
Avoid personal
computers
Choose a central location
Avoid other cordless
telephones
• You should charge your handset for 15-20 hours before using the
phone.
• The location should be close to both a phone jack and continuous
power outlet which is not switchable.
• Keep the base and handset away from sources of electrical noise
such as motors and fluorescent lighting.
• Be sure there is sufficient space to raise the base antenna fully
vertical.
• The base can be placed on a desk, tabletop or mounted on a
standard wall plate.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect the base unit
If you want to install the base unit on the wall, see page 8.
Route the cord.
Place the power cord so it
does not create a trip
hazard, or where it could
become chafed and create
a fire or electrical hazard.
2
To AC outlet
To DC IN 9V
AC adapter
(supplied)
1
To telephone outlet
To TEL LINE
Telephone line cord
(supplied)
1
2
3
Connect the telephone line cord to the TEL LINE jack and to
a telephone outlet.
Connect the AC adapter to the DC IN 9V jack and to a
standard 120V AC wall outlet.
Set the base unit on a desk or
tabletop and place the handset
on the base unit.
Then raise the antenna to a
vertical position.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Use only the supplied AD-420
AC adapter. Do not use any other
AC adapter.
Polarity of the plug
Connect the AC adapter to a
continuous power supply.
Place the base unit close to the
AC outlet so that you can unplug the
AC adapter easily.
Modular
If your telephone outlet isn't modular,
contact your telephone company for
assistance.
Choose the dialing mode
PULSE
TONE
Depending on your dialing system, set the PULSE-TONE switch as
follows:
If your dialing system is Set the switch to
Tone
Pulse
TONE
PULSE
If you aren't sure of your dialing system
Make a trial call with the PULSE-TONE switch set to TONE.
If the call connects, leave the switch as is; otherwise, set to PULSE.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting the base unit on a wall
Standard wall plate mounting
This phone can be mounted on any standard telephone wall
plate.
1
2
Snap the wall mount
adapter into the
notches on the base.
1
Plug the telephone
line cord to the
TEL LINE jack and the
AC adapter to the
DC IN 9V jack.
3
4
Plug the telephone
line cord into the
telephone outlet.
Wrap the AC adapter
cord inside the
molded wiring
2 - 7
channel. Then wrap
the cord around the
strain relief notch.
5
Plug the AC adapter
into a standard
120V AC wall outlet.
6
7
Raise the antenna to a
vertical position.
Align the mounting
slots on the base with
the mounting posts on
the wall. Push in and
down until the phone
is firmly seated.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
8
9
On the base unit, pull the
handset retainer out of the slot.
Rotate it clockwise
Handset retainer
180 degrees.
Flip the retainer from front to
back. Slide it back into the slot
so that the lip of the retainer is
If you have wall mounted
the base, you must remove
the beltclip to charge the
handset facing forward.
up and the
symbol is
pointed down. The retainer
holds the handset
in place.
Direct wall plate mounting
If you don't have a standard wall plate, you can mount your phone
directly to the wall. Before doing this, consider the following:
• Avoid electrical cables, pipes, or other items behind the mounting
location, that could cause a hazard when inserting screws into
the wall.
• Try to mount your phone within 10 - 15 feet of a working phone
jack to avoid excessive cord lengths.
• Make sure the wall material is capable of supporting the weight of
the base and handset.
• Use #10 screws (minimum length of 1-3/8 inches) with anchoring
devices for the wall material where the base unit will be placed.
TOP
1
2
Insert two mounting screws
into the wall, (with their
3/16 in.
appropriate anchoring device),
3-15/16 inches apart. Allow
about 3/16 of an inch between
the wall and screwheads for
mounting the phone.
3-15/16 in.
Refer to steps 1 through 9 on
page 8 and 9 to mount the
telephone.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the handset battery pack
Charge the battery pack for 15-20 hours before you start using
your phone.
1
2
Press in on the battery cover
release and slide the cover
down until it comes off.
Connect the battery pack
connector with the correct
polarity (black and red
wires), then insert the battery
pack into the battery
compartment.
3
4
Slide the battery cover
forward until it snaps into
place.
Place the handset on the
base.
5
Make sure that the “status”
LED lights. If the LED
doesn’t light, check to see
that the AC adapter is
plugged in and that the
handset makes good contact
with the base charging
contacts.
status LED
Use only Uniden Battery (BT-905) supplied with your
phone.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery use time (per charge)
From fully charged
• Six hours coutinuous use
• Ten days when the handset is in the standby mode
When the battery charge becomes low
When the voltage of battery pack in the handset is very low and
needs to be charged, the phone is programmed to eliminate
functions in order to save power. If the battery charge becomes low,
talk/batt LED blinks. If the phone is in use, the handset beeps.
Complete your conversation as quickly as possible and return the
handset to the base unit for charging.
Even when the battery
pack is not being used, it
will gradually discharge
over a long period. For
optimum performance, be
sure to return the handset
to the base unit after a
telephone call for
charging the battery.
Cleaning the charging contacts
To maintain a good charge, it is important to clean the charging
contacts on the handset and base unit with a dry cloth about once a
month.
Do not use any liquids or solvents.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Making a call
talk
. The talk/batt LED
1
Press
lights.
2
3
Dial the phone number.
talk
To hang up, press
or return the
handset to the base.
If the talk/batt LED does
not stop flashing, place
the handset on the base
for at least three seconds
and make a call again.
Other Operations
To
Do this
•
ª
To adjust the ear speaker volume
Press
or
during the call.
tone
To temporarily switch to tone dial Press
. The following
(When the base is set to pulse
mode)
numbers will be sent as tone
dialing.
To improve reception
Press channel .
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Receiving a call
From the handset
Handset on the base
1
2
3
The phone rings. The talk/batt LED
flashes.
When you receive a call
during a page or memory
dialing operation, press
talk to answer the call.
Pick up the handset and begin
speaking.
talk
To hang up, press
or return
the handset to the base.
Handset off the base
1
2
3
Phone rings. The talk/batt LED
flashes.
talk
Press
or any key (except
mute
) and begin speaking.
talk
To hang up, press
or return
the handset to the base.
From the base
1
The phone rings. The status LED
on the base flashes.
speaker
2
3
Press
and begin speaking.
The base microphone is
located under the phone.
Position yourself as near
to the base as possible and
speak clearly.
speaker
To hang up, press
.
status LED
Microphone
Ringer mute
You can temporarily mute the handset’s ringer by pressing
mute
talk
when the phone rings. You may still press
to answer
13
the call.
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the volume
Handset ringer tone and volume
Press ringer repeatedly in standby
mode to select one of four types ringer
tone and volume combinations.
•
ª
ringer
Ringer on/off switch
This switch turns the handset ringer on or off.
ringer
of
f
o
n
ringer
of
f
on
Handset earpiece volume
The phone has four earpiece volume levels, Normal, Medium,
•
High, and Loud. Pressing
or
during a telephone call will
ª
change the earpiece volume of the handset. This setting will
remain in effect after the telephone call has ended.
•
When you press
in Loud mode or press
in Normal
ª
mode, error sound beeps.
Base ringer switch
This switch turns the base
ringer on or off.
RINGER
OFF–ON
Base speaker volume
To control the speaker volume of the
volume •
base, adjust the
and
volume ª
button as desired.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Flash and Call Waiting
If you have “Call Waiting” service and a
call waiting tone sounds while you are
flash
on a call, press
to accept the
waiting call. There is a short pause, then
you will hear the new caller. To return
to the original caller, press flash again.
flash
Redialing a call
The last phone number dialed can be quickly redialed.
1
Press talk . The talk/batt LED
lights.
redial
2
3
Press
.
If the recently dialed
talk
To hang up, press
handset on the base.
or place the
number exceeds 32 digits,
only the first 32 digits are
retained for redialing.
Mute
You can turn off the handset microphone and temporarily mute
the ringer.
When speaking on the handset
1
Press
during a telephone call.
mute
The talk/batt LED blinks.
The other party will not be able to
hear you although you can hear
them.
2
To cancel mute, press talk or mute
again.
talk
When the phone is ringing
Press mute when the phone rings. The ringer sound turns off.
You may still press talk to answer the call.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Traveling out-of-range
During a call, as you begin to move your handset too far from your
base unit, noise increases. If you pass the range limits of the base
unit, your call will terminate within 30 seconds.
Using the page feature
1
To locate the handset (while it’s off
page
the base), press
on the base.
The handset beeps for 5 seconds.
page
Press and hold
for more than 2 seconds to page
the handset for a minute. Press any key or return the
handset to the base to cancel the page.
page
If you hold down
for more than a minute, the
page
handset beeps until you release
.
If you cancel the page by
pressing talk , press
again to return to
talk
standby.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Storing phone numbers
Your EXS 2050 stores up to 10 numbers in the handset.
mem
while in standby mode.
The talk/batt LED flashes.
1
2
Press
Dial the number you wish to store (up to
20 digits).
You must press a key
within 20 seconds or the
phone will return to
standby. If you return the
handset in the cradle, the
phone will return to
standby too.
mem
again.
3
4
Press
Enter a number key (0 - 9) to select the
memory location where you wish to
store the number.
5
The talk/batt LED goes out and the
confirmation beep indicates the number
has been stored.
pause
Press
to enter a pause in the dialing sequence.
The pause feature is useful for long distance calling, credit
card dialing, or sequences that require a pause between
digits.
Use the supplied memo sticker to write stored numbers.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Making calls with memory dialing
Memory dialing
talk
1
Press
lights.
. The talk/batt LED
mem
2
3
Press
.
Enter a number key (0 - 9) to
select the memory location you wish
to dial.
4
To hang up, press talk or return
the handset to the base.
Chain dialing
On certain occasions after dialing a number, you may be
requested to enter an access code, such as your account number.
You can enter this number into a memory location for later use
by doing the following:
1) Store the access code into one of the memory locations (0-9)
following the steps on page 17.
2) Dial the party or service main number.
3) When you need to enter the special number, press
followed by the memory location (0-9).
mem
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Erasing a stored phone number
mem
in the standby mode.
The talk/batt LED flashes.
1
Press
2
3
Press mem again.
Enter a memory location number
(0 - 9) you wish to delete.
A confirmation beep indicates the
number has been erased.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3-way conferencing
The Uniden EXS 2050 permits
3-way conversations between
the handset, base and outside
line.
Dialing is possible only
from the handset during
the 3-way conversation.
When speaking on the handset
speaker
on the base to join
the 3-way conversation.
1
2
Press
speaker
To hang up, press
on the
base. The handset will still be
connected to the call.
If you pick up the handset
from the base while
speaking on the base, the
call will be transferred to
the handset.
When speaking on the base
talk
on the handset to join
the 3-way conversation.
1
2
Press
To hang up, return the handset to the
talk
base, or press
on the handset.
The base will still be connected to the
call.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Integrated answering device
The EXS 2050 has a built-in answering system that answers and
records incoming calls.
You can also use your answering system to record a conversation,
leave a voice memo message for others who use the phone, or to
announce a special message to callers when you're away from
your phone.
Features
• Digital Tapeless Recording
• 15 minutes of Recording Time
• Selective Greetings (Outgoing Messages)
• Time and Day Stamp
• Remote Message Retrieval and Room Monitor
• Toll Saver
• Conversation Recording
Digital Tapeless Recording allows you to quickly review, save or
delete the messages. You'll never have to worry about a tape
wearing out, jamming, or resetting improperly.
The Integrated Answering System is easy and convenient to use,
but please read through all of the instructions carefully.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting up your answering system
Turning the answering system on/off
1
To turn the answering system on,
press answer on/off
.
The current greeting message is
played and a tone sounds.
If you have not recorded
your personal outgoing
message when you turn
the answering system on,
the preset message is
automatically set. To set
your personal message, see
page 23.
2
To turn the answering system off,
press
again.
answer on/off
When the answering system is full, FL displays on the
base and the system announces “No remaining time”.
You should delete some messages so that the system
can record new messages.
Setting the clock
The clock on the EXS 2050 Answering System starts when power
is applied to the base. Follow these steps to set the clock to the
correct time.
clock
1
2
Press and hold
sounds.
until a tone
repeat
or
skip
First, press
repeatedly until the correct day of
the week is announced. (Numbers
through display on the base as
each day is announced.) Press
clock again to select the day.
Holding skip
repeat
or
to scroll
through days, hours,
minutes, etc.
skip/
skip
3
4
Next, press
or
repeatedly until you
repeat
hear the correct hour setting. Numbers through display
on the base as each hour is announced. Press
to select the correct time.
clock
again
If you don't set the clock
within two minutes, the
system returns to standby.
Press skip
or
repeatedly until you hear
through display on
again to
repeat
the correct time setting. Numbers
the base as each minute is announced. Press
select the correct time.
clock
22
Download from Www.Somanuals.com. All Manuals Search And Download.
skip
5
6
The LED displays or . Press
or repeat
until you hear the correct AM/PM setting.
clock
Press
again to end the time/day setting.
The EXS 2050 announces the time that you have set.
Setting your greeting
When you receive a call, the answering system automatically
plays either a preset message or your own greeting.
ª
Preset Message
The following message is prerecorded:
"Hello, no one is available to take your call. Please leave a
message after the tone."
ª
Recording a personal outgoing message (Greeting)
greeting
until you
1
Press and hold
hear a tone. Start recording your
message immediately after you hear
the tone end.
You can record a greeting
up to 30 seconds.
2
When you finish recording your
greeting
message, press
or
play/stop .
A tone sounds and your message
plays back on the phone.
ª
Choosing between the two outgoing messages
Position yourself as near
to the base as possible and
speak clearly when
recording your outgoing
message.
greeting
to play the
1
2
Press
outgoing message.
greeting
Press
again while the
message is played. This switches
between the two options.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Selecting the message record time
You can set your answering system to record messages between
one to four minutes long.
One minute option:
move the REC TIME
switch to 1.
Four minute option:
move the REC TIME
switch to 4.
REC TIME
ANN/4/1
ª
Announce only feature:
The announce only feature plays an outgoing message, but it will
not allow the caller to leave a message. Move the REC TIME
switch to the ANN position.
The message counter LED displays “ ” when system is on
standby.
The prerecorded outgoing message for Announce only feature is:
"Hello, no one is available to take your call."
Selecting a PIN code
To play your messages from a remote location, you will need to
enter a two-digit Personal Identification Number (PIN) code
(00-99). To select a PIN, perform the following steps.
pin
1
2
On the base, press and hold
until a tone sounds and the LED
displays
.
To set the first number, press
repeat
skip
or
Press and hold
skip
or
to scroll
repeatedly to scroll from 0 to 9.
When the desired number appears in
the display, press pin .
repeat
through numbers on the
display.
skip/
3
To set the second number, press
repeat
skip
or
to scroll
from 0 to 9. When the desired
number appears in the display, press
pin
. Then the entered PIN is
announced.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting ring time switch
The ring time/toll saver switch
allows you to set the number of
rings the caller hears before the
answering system plays your
outgoing message. You can set
the switch to answer after two
rings or after four rings.
RING TIME
2/4/TS
Once the greeting has started, you can stop it when you pick up
the call at the handset or base.
If you answer at another phone extension and the
greeting has started, you cannot stop the message.
Wait until your greeting is complete before starting
your conversation.
In the TS (Toll Saver) position, the answering system picks up
after two rings if you have new messages, and after four rings if
there are none. This way, if you call long distance to check your
messages, you can hang up after the third ring to avoid billing
charges.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Using your answering system
Playing your messages
The base LED shows the number of total messages on the
display. If the display is blinking, then there are new messages
waiting for you. The EXS 2050 is designed to play your new
messages first. After you play your new messages, you can then
play your old messages.
To stop playing your
messages, press
play/stop
again.
play/stop
. The system
1
Press
announces the number of new and
old messages, then the incoming
messages are played. The time and
day each message was received is
announced after the message is
played, and the message counter
LED displays the number of the
current message.
2
3
When all new messages have
played, a tone is heard. The message
counter LED stops flashing to
indicate that all of the new messages
have been reviewed.
After you have reviewed all your
messages, you can play your old
play/stop
messages again. Press
and follow the instructions above.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Repeating a message
play/stop
message. The number of stored
messages is announced.
1
2
3
Press
to review your
repeat
Pressing
before 2 seconds (4
After a message has played for a few
seconds, press
repeat the message.
seconds from remote) of
the message has played
causes the system to scan
back one message.
repeat
to
play/stop
Press
at any time to stop
reviewing messages and return to
standby. The message counter LED
shows the total number of messages
remaining on the system.
If you have several
messages, press and hold
repeat
until you
return to the message you
want to replay.
Skipping a message
play/stop
1
Press
to review your
messages. The number of messages
is announced.
skip
Each time
is
pressed, the system scans
forward one message.
2
3
Press skip
to the next message.
at anytime to skip
play/stop
Press
at any time to stop
reviewing your messages and return
to standby. The message counter
LED shows the total number of
messages on the system.
If you have several
messages, press and hold
skip
to find the
message you want to play.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Deleting a message
ª
Deleting individual messages
play/stop
to review your
message.
1
2
Press
If you decide to delete a message,
press delete anytime during the
message. The system beeps and
immediately goes to the next
message.
delete
When you press
,
you are permanently
deleting the message and
the message cannot be
replayed.
ª
Deleting all messages
delete
Press and hold
while the system is in standby. A tone
sounds when all messages are deleted.
If there is a message you have not reviewed, you cannot delete
all messages at once.
The voice memo function
is completely independent
of the outgoing message.
It’s handy for leaving
others a quick message.
Voice memo
The voice memo function allows the user to record a message
(up to 10 minutes) on the base.
voice memo
1
Press and hold
A voice memo message
will be stored as a typical
recorded message.
until you hear a tone. The
message counter LED blinks.
2
3
Speak into the microphone.
When you have finished, press
voice memo
play/stop
or
to
stop recording. The system returns
to standby.
Microphone
Position yourself as near
to the base as possible and
speak clearly.
4
To play voice memo, press
play/stop
.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Recording a conversation
You can record up to 10 minutes of conversation while you are
making your call from the handset.
1
During the conversation from the
voice memo
handset, press and hold
on the base. The unit begins
recording and the LED blinks. Both
parties can hear tones every 15
seconds.
A recorded conversation is
stored and played back
with typical recorded
messages.
2
To stop the recording, press
voice memo
or
.
play/stop
You cannot record a conversation while you are
speaking on the base.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote access away from home
You can operate your answering system from a remote location
using any touch-tone telephone. Use this function to check for
recorded messages, to play or delete messages, to record a new
outgoing message, and to monitor sounds in the room.
During the remote
operation,
on the base.
displays
1
2
Call your telephone number.
While the greeting message plays, press # and your PIN
code.
If the answering machine is off, let it ring 10 times until the
greeting message plays.
Then, press # and your PIN code.
3
4
The answering system announces the time and day stamp
and the number of messages stored in memory. Then the
message playback automatically begins.
You must enter a
command within 15
seconds of entering the
command waiting mode
or the answering system
automatically hangs up
and returns to standby.
You may continue to listen to your message or you may
select a command from the following chart.
Command Function
# then 1
# then 2
# then 3
# then 4
# then 5
# then 6
# then 7
Repeat
Playing your messages
Skipping a message
Deleting a message
Stop message playback
Answering system on
Voice memo record/stop
(up to 4 minute recording time)
Greeting message record/stop
Answer system off
The system will only play
back messages for four
minutes and then it
# then 8
returns to the command
waiting mode. To continue
playing your message,
press # then 2 again
within 15 seconds
# then 9
# then
Room monitor
*
5
6
After all of your messages have played, or the playback time
exceeds 4 minutes, you will hear intermittent tones indicating
that the system is in the command waiting mode. You may
enter another command at this time from the chart above.
When you finish, hang up to exit the system.
The answering system automatically returns to standby.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote room monitor
You can call your answering system from any touch-tone phone
to monitor sounds in the room where your base is installed.
1
2
Call your telephone number.
While the greeting message is played, press # and your PIN
code.
3
4
5
The answering system begins announcing the time and day.
You cannot use # and
*
while the new messages
are playing. Press # then
5 to stop message
playback first and go to
step 5.
Press # then 5 to stop the messages.
Press # then . You hear sounds in the room where your
*
phone is installed. After 15 seconds, the answering system
returns to the command waiting mode.
6
Press # then
to monitor the room for another 15 seconds.
*
Select another remote function or hang up to exit the system.
The answering system automatically returns to standby.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the digital security code
The digital security code is an identification code used to connect
the handset and the base unit. Normally, setting the code is not
necessary.
If the handset battery pack
is completely discharged
or the battery pack is
removed, the digital
security code will be lost.
If this happens, a new
security code is set
The first time you charge your handset, the security code is
automatically set.
In the rare situation that you suspect another cordless telephone
is using the same security code, you can change the code.
automatically next time
the battery pack is
charged.
1
2
Remove the handset from the base
page
unit. Press and hold
.
While the handset is emitting the
paging sound, place the handset on
page
the base unit holding
The paging tone stops.
.
Leave the handset on the base for
more than 3 seconds. A random,
new security code is set.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the beltclip
To attach the beltclip
To remove the beltclip
Insert the beltclip into the holes
on each side of the handset.
Press down until it clicks.
Pull both sides of the beltclip to
release the tabs from the holes.
If you have wall mounted
the base, you must remove
the beltclip to charge the
handset facing forward.
Headset installation
Your phone may be used with
an optional headset, the Uniden
HS910. To use this feature, insert
the headset plug into the headset
jack. Your phone is ready for
hands-free conversation.
headset
jack
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Note on power sources
RECYCLING NICKEL-
CADMIUM BATTERIES
Battery replacement
and handling
When the operating time
becomes short, even after the
battery is recharged, please
replace the battery.
With normal usage, your
battery should last about one
year.
NICKEL-
CADMIUM
BATTERIES
MUST BE
DISPOSED OF
PROPERLY.
Ni-Cd
Please contact your place of
purchase for a replacement
battery.
Nickel-cadmium cells are used
in the battery pack. Please
take your used nickel-
Power Failure
cadmium battery packs to a
store that recycles nickel-
cadmium batteries.
During the period that the
power is off, you will not
be able to make or receive
calls with the telephone.
Caution
• Use the specified battery pack.
• Do not remove the battery from the handset to charge it.
• Never throw the battery into a fire, disassemble it, or heat it.
• Do not remove or damage the battery casing.
Maintenance
When slightly dirty
Caution
Wipe with a soft, dry cloth.
Do not use paint thinner,
When very dirty
benzene, alcohol, or other
chemical products. Doing
so may discolor the surface
of the telephone and
Wipe with a soft cloth that has
been dampened with diluted,
neutral detergent. Dry with a
dry cloth.
damage the finish.
When the charging
terminals become dirty
Wipe with a dry cloth.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
If your phone is not performing to your expectations, please try
these simple steps first.
Symptom
Suggestion
The status LED won't • Make sure the AC adapter is plugged
come on when the
handset is placed in
the base unit.
into the base unit and wall outlet.
• Make sure the handset is properly
seated in the base unit.
• Make sure the charging contacts on the
handset and base unit are clean.
channel
The audio sounds
• Press
to help eliminate
weak and/or scratchy.
background noise.
• Make sure that the base unit antenna is
in a vertical position.
• Move the handset and or base unit to a
location away from metal objects or
appliances and try again.
• Make sure that you are not too far from
the base.
Can't make or receive
calls.
• Check both ends of the base unit
telephone line cord.
• Make sure the AC adapter is plugged
into the base unit and wall outlet.
• Disconnect the AC adapter for a few
minutes, then reconnect it.
talk
• Make sure
is pressed.
The handset doesn't
ring or receive a page.
• The battery pack may be weak. Charge
the battery on the base unit for 15-20
hours.
• The handset may be too far away from
the base unit.
• Place the base unit away from
appliances or metal objects.
• Make sure the ringer on/off switch is set
to on.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Suggestion
The answering system • Make sure the base unit is plugged
does not work.
in.
• Make sure that the answering system
is turned on.
Messages are
incomplete.
• The incoming messages may be too
long. Remind callers to leave a
brief message.
• The memory may be full. Delete
some or all of the saved messages.
After a power failure,
the outgoing message
is deleted.
• Record your greeting again.
The preset messages should remain.
No sound on the base • Adjust the speaker volume on the
unit speaker during call
monitoring or message
playback.
base unit.
Cannot access remote
call-in features from
another touch-tone
phone.
• Make sure you are using the correct
PIN number.
• Make sure that the touch-tone phone
you're using can transmit the tone
for at least two seconds. If it
cannnot, you may have to use
another phone to access your
message.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
At Uniden, we’ll take care of you!
If you need any assistance with this product, please call our Customer Hotline at
1-800-297-1023
PLEASE DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.
Our Uniden representatives will be happy to help you with any
matters regarding the operation of this unit, available accessories,
or any other related matters.
Thank you for purchasing a Uniden product.
Hours: M-F 7:00 AM to 7:00 PM CST.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Mute ......................................15
0 - 9
3-way conferencing..............20
P, Q
Package contents....................4
A
Answering device
R
Features...........................21
Setting up........................22
Using...............................26
Receiving a call ....................13
Redialing a call.....................15
S
B
Setting up your answering
system
Base ringer switch................14
Battery pack
Selecting a PIN code......24
Selecting the
message record time......24
Setting the clock.............22
Setting ring time
Preparing and
charging ..........................10
Replacement and
handling..........................34
switch..............................25
Setting your greeting......23
Turning the answering
system on/off..................22
Setup
C
Connection..............................6
D
Dialing mode..........................7
Digital security code .........3,32
Base unit...........................5
Handset...........................10
E, F, G
Earpiece volume...................14
T
Troubleshooting....................35
H
Handset ringer tone
and volume....................14.
Headset installation..............33
U, V, W, X, Y, Z
Using your answering system
Deleting a message........28
Playing your message ....26
Recording a
I, J, K, L
Installing the beltclip............33
conversation ...................29
Remote access
M, N, O
Maintenance..........................34
Making a call........................12
Memory dialing
away from home............30
Remote room monitor....31
Repeating a message......27
Skipping a message .......27
Voice memo....................28
Erasing a stored
phone number................19
Making a call
with memory dialing......18
Storing phone
numbers..........................17
Mounting the base unit
to a wall..................................8
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|