IMPORTANT!
1. Remove clear sticky
plastic transit tape.
1
QuickStart GUIDE
RIO 2e & TANGO 2e Printers
2
2. Remove backing
label from sticky
roller prior to use.
Unpacking
Rio 2e/Tango 2e
1
How to clean your printer
Hopper and Stacker
Power Cable
USB Cable
USB Port
Driver CD
We recommend you purchase a Cleaning Kit (Magicard part no. M9005-761) which consists of cleaning cards, pens and rollers.
We recommend that you clean your printer using a cleaning card each time you replace the dye-film.
To clean the printer feed mechanism :
•
•
•
•
Remove the card hopper and open the top door (the red light comes on).
Take a fresh cleaning card from its packaging.
Insert the narrow end into the card feed slot.
Attach the card output stacker
Printer location requirements
Press the black button on the back of the printer (located above the USB connector). The card is drawn into the printer and
then ejected. Repeat this several times with both sides of the same card.
Consumables
2
3
4
Cleaning Cards & Roller
Dye Film and Cards
Insert the card collection stacker into the
aperture in the front panel and hook into place.
The stacker can hold
• Sufficient space for:
- opening the top cover
- cable access at the rear.
- allowance for air circulation.
•
•
To ensure that the rear feed rollers situated under the card hopper are thoroughly cleaned, set the printer to its cleaning cycle,
and instead of inserting the card, simply hold it against these rollers.
up to 50, 30mil thick
cards, after which it
should be emptied.
The printer can be
operated without the
stacker if you wish.
• An adequately ventilated dust free room.
• Access to a properly grounded power supply.
• Ambient temperature +10 to 30 degrees C.
• Relative humidity 20 - 70%.
• Protection from direct sunlight and chemicals.
• Protection from abrupt temperature changes.
You are provided with 5 cleaning cards and one roller with your printer.
Replacing the cleaning roller
Note: To complete installation and begin using
your printer you will require a roll of Magicard
dye-film and cards (not included).
There is a cleaning roller inside the printer. It is recommended that it is replaced after every 1,000 prints. A spare roller is provided
with each printer.
To see instructions for replacing the cleaning roller, see section 6 (‘Prepare the cleaning cassette’) in this guide. You re-use the
cassette, but replace the roller within it.
Attach the Card Feed Hopper
Prepare the cleaning cassette
5
6
1. Open a clean pack of cards and make sure they are
not sticking together. Load the cards into the feed
hopper. Avoid touching the card surfaces because
finger marks can effect image quality.
Press down on the top cover, operate the top cover
release catch and open the cover. First remove the white
tape holding the black plastic cleaning cassette. Grip the
handle between finger and thumb, then push and release
the cleaning cassette. Remove the
To clean the printhead :
Open the printer and draw the pen several times, in the same direction, along the complete length of the printhead.
The only other user maintenance is replacement of the printhead. This should normally only be necessary following damage by dirt ,
so cards must be kept clean before loading into the printer.
Note: When using magstripe cards,
ensure the stripe is on the right and
underneath when viewed from the front.
orange tape and protective layer
from the disposable cleaning
2. Tilt the loaded hopper back as shown, and lower gently
cassette roller.
into the receptacle at the rear of the printer. You will be
able to lower the hopper about an inch (25mm).
3. At this point, tilt the hopper forward to the vertical position
and lower all the way down until the hopper is completely
within the body of the printer.
Note: This is a good time to familiarise yourself with the
way that this automatic cleaning system is designed to
operate.
Finally replace the cleaning cassette by inserting the roller
shaft into the U shaped guides and clicking into place.
How to set up your Rio 2e and Tango 2e to use HoloPatch cards
When used with HoloPatch cardstock, the HoloKote watermark provides a defense against card fraud. Cards with this feature are
available for both plain and magstripe formats.
To select this feature, ensure that the card design allows space for the HoloPatch cut-out. In the printer driver, set HoloPatch to ‘Yes’ and
click OK. Cards will be printed with a ‘cookie cutter’ hole in the image lining up with the gold patch on the card.
Note: HoloPatch cards should be fed with the gold patch on top, and on the right-hand side (viewed from the front).
Plug in the printer
Install the dye film
7
8
1. Open a new roll of dye film.
Make sure that the printer is turned Off, i.e. the On/Off
button is slightly protruding from the front panel.
2. Place the loaded spool into the rear clips and press it into place.
The orientation is correct when the bar code on the end of the spool to
the left hand side when viewed from the front. Rotate to make sure that
the slot engages with the lug.
3. Place the empty take up spool into the front clips,
and adjust the film tension so that the film is lying
flat and straight between the two spools.
How to adjust card thickness
The print engine adjusts automatically to the cards used. However, to prevent misfeeds the card feed preventor should be set using
the lever in front of the card hopper which is best accessed by removing the cleaning cassette. Card thicknesses between 0.38mm
to 1.6mm can be accommodated.
Plug the power supply lead provided into the socket
on the rear panel of your printer, and the other end
into a properly grounded electrical outlet.
4. Press the top cover down until it clicks into the
closed position. The printer will automatically
recognize the type of film that has been loaded.
How to use a custom key to:
• Print custom HoloKote watermarks.
• Lock the printer.
Print a test card
Load the CD into your PC
10
9
The printer should be set up before introducing you custom key with the power switched off. Insert the key into the slot on the lower
left hand side of the front of the printer, ensuring the correct orientation which is clearly marked on the label, and the key is pushed
in. Now switch on the printer. Providing the key is not removed, all cards printed will now include your own custom mark into the
HoloKote pattern.
If the custom key has been programmed with a locking facility, then the printer will not allow any card printing or encoding
operationunless the original locking custom key is inserted before before powering up the printer remains in place.
Note: Do not insert or remove the custom key while the printer is powered on as this may damage the key.
Note: Driver settings are available to adjust the orientation of the custom mark for 0°, 90°, 180° and 270°.
1. Switch the printer on. You will hear some motor activity and see the
indicators flash.
2. When ready, the red Error indicator should be off and the green
indicator on.
3. Press and release the small test push button on the
rear panel once.
4. After several seconds, the printer will print a test
pattern on a card, and feed it to the card output
stacker. This indicates that all is well with the
printer, i.e. cards loaded, dye film loaded, power
is on and lid is closed.
Make sure the printer is switched off. Load the driver CD ROM into the
PC you have connected to the printer. If the CD does not run
automatically, click the start button, then click on “run”.
Type “D:\autorun”, where D is the drive letter
for your CD drive, then press the return key.
Now follow the on screen instructions to install the
printer drivers. On completion of installation, you
will be able to print cards.
WARNING. Only connect one interface (USB or Ethernet
or Parallel) to your PC. Do not connect multiple interfaces,
as this can cause incorrect operation.
How to use magnetic stripe cards
When loading magnetic stripe cards, make sure that the stripe is on the right and underneath when viewing from the front of the printer.
Rio 2e and Tango 2e QuickStart Guide. Drawing No. 3627-22-05 Issue 2, August 2007 (Stock No. M9007-158/R)
Download from Www.Somanuals.com. All Manuals Search And Download.
|