Use and Care Guide
®
Combo Models:
CO29, CO75
CO29
CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Table of Contents
Introduction ...............................................................................................................................2
Warranty Registration .......................................................................................................2
Please Record Your Model Information ...........................................................................2
Table of Contents .......................................................................................................................3
Safety Precautions ......................................................................................................................5
Safety Alert Definitions .....................................................................................................5
General Precautions ...........................................................................................................5
Product Features ........................................................................................................................6
Origins Ice Maker/Refrigerator Models CO29, CO75 .......................................................6
Operation ...................................................................................................................................6
Initial Startup .....................................................................................................................6
Temperature Control .........................................................................................................7
Ice Maker ............................................................................................................................7
Normal Operating Sounds .................................................................................................8
Outdoor, Marine and RV Usage ........................................................................................8
Storage, Vacation, Moving ................................................................................................8
Product Disposal .................................................................................................................9
Cleaning and Maintenance .......................................................................................................9
General Cleaning ...............................................................................................................9
Maintenance ....................................................................................................................10
Service .......................................................................................................................................18
Before Calling for Service ................................................................................................18
If Service is Required ........................................................................................................18
Replacement Parts ...........................................................................................................18
Troubleshooting Guide ....................................................................................................19
U-Line Corporation Limited Warranty ....................................................................................23
CO29, CO75
3
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
4
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
3 Safety Precautions
SHOCK HAZARD - Electrical Grounding Required.
• Never attempt to repair or perform
maintenance on the unit until the electricity
has been disconnected.
• Never remove the round grounding prong from
the plug and never use a two-prong grounding
adapter.
• Altering, cutting of power cord, removal of
power cord, removal of power plug, or direct
wiring can cause serious injury, fire and/or loss
of property and/or life, and will void the
warranty.
IMPORTANT
PLEASE READ all instructions completely before
attempting to install, operate, or service your unit.
• Proper installation procedures must be followed
if this unit is being initially installed, or is moved
to a new location after being in service. An
INSTALLATION GUIDE for your unit, providing
complete installation information is available
from U-Line Corporation directly, and must be
consulted before any installation is begun. U-Line
contact information appears on the rear cover of
this guide.
• Never use an extension cord to connect power
to the unit.
• Always keep your working area dry.
• This unit requires connection to a grounded
(three-prong), polarized receptacle that has been
placed by a qualified electrician in accordance
with applicable electrical codes.
CAUTION
• Use care when moving and handling the unit. Use
gloves to prevent personal injury from sharp
edges.
• If your model requires defrosting, DO NOT use any
type of heater to defrost. Using a heater to speed
up defrosting can cause personal injury and
damage to the inner lining.
Safety Alert Definitions
Safety items throughout this guide are labeled with a
Danger, Warning or Caution based on the risk type:
DANGER
Danger means that failure to follow this safety
statement will result in severe personal injury or
death.
IMPORTANT
• Do not lift unit by door handle.
• Never install or operate the unit behind closed
doors. Be sure front grille is free of obstruction.
Obstructing free air flow can cause the unit to
malfunction and may void the warranty.
• Failure to clean the condenser every three months
can cause the unit to malfunction. This could void
the warranty.
WARNING
Warning means that failure to follow this safety
statement could result in serious personal injury
or death.
CAUTION
• Allow unit temperature to stabilize for 24 hours
before use.
Caution means that failure to follow this safety
statement may result in minor or moderate
personal injury, property or equipment damage.
• If your model requires defrosting, never use an
ice pick or other sharp instrument to help speed
up defrosting. These instruments can puncture
the inner lining or damage the cooling unit.
• Use only genuine U-Line replacement parts.
Imitation parts can damage the unit, affect its
operation or performance and may void the
warranty.
General Precautions
Use this appliance for its intended purpose only and
follow these general precautions along with those listed
throughout this guide:
DANGER
RISK OF CHILD ENTRAPMENT. Before you throw away
your old refrigerator or freezer, take off the doors
and leave shelves in place so that children may not
easily climb inside.
CO29, CO75
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Product Features
5 Operation
Origins Ice Maker/Refrigerator
Models CO29, CO75
• Both Origins models feature a manual defrost ice
maker with a daily production capacity of 18 lbs (8.2
kg) and storage for 13 lbs (5.9 kg).
ULIN_0130_A
• Model CO29 provides 2.1 cu ft (59 L) of refrigeration
capacity; Model CO75 provides a 4.2 cu ft (118 L) of
refrigeration capacity.
Figure 2
• Temperature is adjusted with a manual temperature
control.
IMPORTANT
Proper air flow (Figure 2) is required for your unit to
operate at its highest efficiently. A grille, located in
the base of the unit, must not be blocked at any
time, or your unit will not perform as expected.
• Tempered glass shelves are easy to clean. Model CO29
has two shelves; Model CO75 has three shelves.
• In-door storage shelves with clear bottle retainers are
standard. Model CO29 has two shelves; Model CO75
has three shelves.
Initial Startup
• Both models accept custom 1/4" (0.64 cm) door panels,
to provide a custom, built-in look by matching
surrounding cabinets.
All U-Line units are shipped with controls that are preset.
No initial adjustments are required.
• All models are field-reversible.
IMPORTANT
• Both models feature a vinyl clad steel cabinet that
provides a rich textured look, and resists scratching,
peeling and flaking.
• U-Line recommends the unit be allowed to run
overnight prior to loading the refrigerator and/or
freezer with product.
• On ice maker equipped units, it is possible that
dirt or scale will dislodge in the water line.
Always throw away all ice cubes made during the
first two to three hours of operation.
Features and specifications are subject to change without
notice.
ULIN_0129_A
Figure 3
To turn the unit on or off, press the rocker switch (Figure
3) located below the temperature control dial in the
center of the grille.
6
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
Temperature Control
Ice Maker
When the ice bucket is full, the ice making mechanism will
shut off. However, the refrigeration system will continue
to cool and maintain the cube supply. Frost-free icemaker
units have lower ice production than manual defrost
units.
Checking Product Temperature
IMPORTANT
Do not place cans or bottles in the ice compartment
because they will freeze.
ULIN_0093_A
Figure 4
To check the actual product temperature, in refrigerator
section only, insert an accurate thermometer into a plastic
(non-breakable) bottle that is partially filled with water.
Tighten the bottle cap securely (Figure 4).
ULIN_0087_A
Figure 6
Ice production may be interrupted by raising the bin arm
into an upright and locked position (Figure 6). The unit
will maintain temperature for ice storage.
Place the bottle in the refrigerator area for 24 hours.
Refrain from opening the unit during the testing period.
After 24 hours, check the temperature of the water. If
required, adjust the temperature control in a small
increment (See ADJUSTING TEMPERATURE).
IMPORTANT
If you are not intending to use the ice maker and
turn the supply valve off, it is imperative to raise
the bin arm of the ice maker (Figure 6). Failure to
raise the bin arm may result in damage to the water
valve.
Factors which affect the internal temperatures of the
cabinet include:
• Temperature setting.
• Ambient temperature where installed.
Certain sounds are normal during the unit’s operation.
You may hear the compressor or fan motor, the water
valve, or ice dropping into the ice bucket.
• Number of times and length of time the door is
opened and closed.
• Installation in direct sunlight or near a heat source.
WARNING
Adjusting Temperature
NEVER use an ice pick, knife or other sharp
instrument to separate cubes. Shake the ice
bucket instead.
1
During periods of limited usage or high ambient
temperatures, it is common for cubes to fuse together.
Shake the bucket to break apart cubes. If the ice maker is
not used regularly, the ice bucket should be emptied
periodically to ensure fresh cubes.
ULIN_0014_A
It is normal for cubes to appear cloudy. This is caused by
air being trapped in the water due to fast freezing. It has
nothing to do with the health, taste or chemical make-up
of the water. It is the same air that is in every glass of
water you drink.
Figure 5
Adjust the temperature by turning the numbered dial
(Figure 5, 1) in small increments.
CO29, CO75
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The ice bucket can be removed for emptying and
cleaning. To remove the ice bucket, raise the bin arm and
remove the bucket from the ice compartment. Use the ice
bucket for ice storage only.
Storage, Vacation, Moving
If the unit will not be used for an extended period, or
otherwise stored, follow these steps completely:
WARNING
Normal Operating Sounds
All models incorporate rigid foam insulated cabinets to
provide high thermal efficiency and maximum sound
reduction for its internal working components. In spite of
this technology, your model may make sounds that are
unfamiliar.
Electrical Shock Hazard. Disconnect power before
servicing. Before operating, replace all panels.
Failure to do so may result in death or electrical
shock.
1. Remove all consumable contents from the unit.
2. Disconnect power to the unit.
Normal operating sounds may be more noticeable
because of the unit’s environment. Hard surfaces such as
cabinets, wood/vinyl/tiled floors and paneled walls have a
tendency to reflect normal appliance operating noises.
3. Shut off water supply to the unit at the main water
source.
Common refrigeration components, and a brief
description of the normal operating sounds they make,
are listed below. NOTE: Your product may not contain all
of the components listed.
IMPORTANT
• If the ambient temperature is expected to drop
below 45°F, turn off and unplug unit, and drain all
water from the unit to prevent freezing damage
not covered by the warranty.
• The use of anti-freeze or other products of this
nature is not necessary and is not recommended.
•
•
•
•
Compressor: The compressor makes a hum or pulsing
sound that may be heard when it operates.
Evaporator: Refrigerant flowing through an evaporator
may sound like boiling liquid.
4. Disconnect the water valve inlet and outlet lines, and
allow them to drain completely.
Condenser Fan: Air moving through a condenser may be
heard.
5. Reconnect power to the unit, and allow it to run for
one hour (minimum) until any remaining ice has been
ejected from the ice maker assembly.
Automatic Defrost/Drain Pan: Water may be heard
dripping or running into the drain pan when the unit is in
the defrost cycle.
•
•
Automatic Ice Maker: You will hear ice as it drops from
the mold into the ice bin/tray.
6. Disconnect power to the unit, dry any remaining water
from the ice maker assembly, and reconnect any lines
removed from the water supply valve.
Water Valve: After an ice maker completes a cycle, a water
valve will make a buzzing sound and running water may
be briefly heard.
7. Disconnect the power cord from its outlet, and leave it
disconnected until the unit is returned to service.
8. Clean and dry the interior of the cabinet (See CLEANING
AND MAINTENANCE: GENERAL CLEANING).
Outdoor, Marine and RV Usage
Some U-Line models are designed to operate in outdoor,
marine and RV environments. For best performance, keep
the unit out of direct sunlight.
9. During periods of non-use, the cabinet must remain
open to prevent the formation of mold and mildew.
Open door a minimum of 2" (5 cm) to provide the
necessary ventilation.
• If the unit will be shut off for five days or more, prop
door open to allow for air circulation and prevent mold
and mildew.
IMPORTANT
If the ambient temperature is expected to drop
below 45°F, turn off and unplug unit, and drain all
water from the unit to prevent freezing damage not
covered by the warranty.
• High ambient temperatures (110°F or higher) may
reduce the unit's ability to reach low temperatures.
8
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
Product Disposal
6 Cleaning and Maintenance
General Cleaning
If the unit is being removed from service for disposal,
check and obey all Federal, State and/or Local regulations
regarding the disposal and recycling of refrigeration
appliances, and follow these steps completely:
Exterior Cleaning (As Required)
1. Disconnect power to the unit and unplug the power
cord from its outlet.
Black or White Models:
• Surfaces may be cleaned with a mild detergent and
warm water solution. Do not use solvent-based or
abrasive cleaners. Use a soft sponge and rinse with
clean water. Wipe with a soft, clean towel to prevent
water spotting.
2. Shut off water supply to the unit at the main water
source and disconnect the supply line to the unit’s water
valve.
DANGER
• Clean any glass surfaces with a non-chlorine glass
cleaner.
RISK OF CHILD ENTRAPEMENT. Before you throw
away your old refrigerator or freezer, take off the
doors and leave shelves in place so that children
may not easily climb inside.
Stainless Models:
• Stainless door panels, handles and frames can discolor
when exposed to chlorine gas, pool chemicals, salt
water or cleaners with bleach.
3. Remove the cabinet door if equipped and secure all
interior shelves to the interior of the cabinet using a
heavy duty cloth or package sealing tape.
• Keep your stainless unit looking new by cleaning with
a good quality all-in-one stainless steel cleaner/polish
®
on a monthly basis. For best results use Claire Stainless
Steel Polish and Cleaner, which can be purchased from
U-Line Corporation (P/N 173348). Comparable products
are acceptable. Frequent cleaning will remove surface
contamination that could lead to rust. Some
installations may require cleaning on a weekly basis.
• Do not clean with steel wool pads.
• Do not use stainless steel cleaners/polishes on
any glass surfaces.
• Clean any glass surfaces with a non-chlorine glass
cleaner.
• Do not use cleaners that are not specifically
intended for stainless steel on stainless surfaces
(this includes glass, tile and counter cleaners).
• If any surface discoloring or rusting appears, clean it
®
®
quickly with Bon-Ami or Barkeepers Friend Cleanser
and a non-abrasive cloth. Always clean in the direction
of the grain. Always finish this process with Claire
Stainless Steel Polish and Cleaner or comparable
product to prevent further problems.
• Using abrasive pads such as Scotchbrite™ will
cause the graining in the stainless to become
blurred.
• Rust that is not cleaned up promptly can penetrate into
the surface of the stainless steel and complete removal
of the rust may not be possible.
Interior Cleaning (As Required)
• Disconnect power to the unit. Clean the interior and all
removed components using a mild non-abrasive
detergent and warm water solution applied with a soft
sponge or non-abrasive cloth. Rinse the interior using a
soft sponge and clean water.
CO29, CO75
9
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use any solvent-based or abrasive
cleaners. These types of cleaners may transmit
taste to the interior products and damage or
discolor the interior.
To defrost:
1. Turn unit off.
2. Remove all products from the interior.
3. Remove ice bucket and discard ice.
4. Place a towel or other absorbent material on bottom of
Maintenance
Proper maintenance of your U-Line product will ensure
efficiency, top performance and long life. The
maintenance intervals listed are based on normal
conditions. You may want to shorten the intervals if you
have pets or other special considerations.
ice bin and bottom of unit (Figure 7, 1)
.
5. You can speed up the defrost process by filling the ice
bucket with warm water, not hot, and place the bucket
back into ice maker housing on the towel or other
absorbent material and close door to unit. Or prop door
open 2" (5 cm) minimum.
Defrosting
Manual Defrost Models - Every Two Months
(Minimum)
6. After approximately 1 hour, remove ice bucket and
discard water.
WARNING
7. Allow the frost to completely melt naturally. Clean the
interior and ice bucket using a mild non-abrasive
detergent and warm water solution applied with a soft
sponge or non-abrasive cloth. NOTE: DO NOT use any
solvent-based or abrasive cleaners. They will discolor or
damage the interior.
DO NOT use any type of electrical heating device,
ice pick, knife or other sharp instrument to
defrost; this could damage the inner lining or
refrigeration system and void the warranty.
8. Dampen a soft sponge or non-abrasive cloth in clean
water and wipe the cabinet interior and ice bucket to
remove any detergent residue. Rinse the sponge or
cloth in clean water and repeat as necessary until the
cabinet and ice bucket are clean, then dry interior with
a clean dry cloth.
IMPORTANT
DO NOT place ice bucket in dishwasher. The heat in a
dishwasher will warp, discolor and damage the ice
bucket.
9. When interior is dry, turn unit back on.
NOTE: To safeguard against contaminants in ice, discard
first three batches of ice after defrosting.
1
ULIN_0224_A
Figure 7
10
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
Condenser Cleaning
Interval - Every Three Months
To maintain operational efficiency, keep the front grille
free of dust and lint, and clean the condenser every three
months. Depending on environmental conditions, more
or less frequent cleaning may be necessary.
WARNING
2
1
Disconnect electric power to the unit before
cleaning the condenser.
ULIN_0198_A
Figure 10
WARNING
6. Make sure grille cap is behind grille in slots provided in
grille (Figure 10, 1) before attaching grille to unit, and
secure but do not overtighten both grille screws
DO NOT touch the condenser fins. The condenser
fins are SHARP and can be easily damaged.
(Figure 10, 2)
.
7. Reinstall the control knob (Figure 8, 1)
.
IMPORTANT
DO NOT use any type of cleaner on the condenser
unit.
8. Reconnect power to the unit.
CO75 condenser:
CO29 Condenser:
1. Disconnect power to the unit.
1. Disconnect power to the unit.
1
2
2
ULIN_0227_A
Figure 11
1
ULIN_0197_A
2. Remove control knob by pulling it straight out, away
from grille (Figure 11, 1)
.
Figure 8
3. Loosen and remove screw (Figure 11, 2)
.
2. Remove the control knob (Figure 8, 1) by pulling it
4. Tilt top of grille forward and remove.
straight out, away from grille.
3. Remove two screws from grille (Figure 8, 2) and save.
1
4. Remove grille and grille cap from unit.
1
ULIN_0226_A
Figure 12
ULIN_0153_A
5. Clean condenser coil (Figure 12, 1) using a soft brush
with a “combing” action or vacuum cleaner. Do not
touch condenser coil.
Figure 9
5. Clean the condenser coil (Figure 9, 1) using a using a
soft brush with a “combing” action or vacuum cleaner.
Do not touch the condenser coil.
CO29, CO75
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Ice Cube Thickness Adjustment
Interval - As Required
On ice maker equipped models, the cube size may be
adjusted by changing the amount of water injected into
the ice maker assembly as follows:
1
2
ULIN_0154_A
Figure 13
6. Place the two hook-hinges (Figure 13, 1) located on
the rear bottom side of the grille onto the front lip of
the unit base. Tilt the grille up into position and align
the grille mounting hole with the grille screw hole on
the cabinet.
automatic
ICE MAKER
7. Insert the screw (Figure 11, 2). Do not overtighten.
8. Reinstall the control knob (Figure 11, 1)
.
9. Reconnect power to the unit.
ULIN_0055_A
Figure 15
Ice Maker Maintenance
Inlet Screen
1. Remove the ice maker assembly cover (Figure 15).
Interval - Every Twelve Months
The solenoid valve inlet screen must be cleaned at least
once each year as follows:
1. Shut off the water at the main supply valve.
2. Pull the unit out to access the back panel.
3. Disconnect electrical power to the unit.
2
ULIN_0056_A
Figure 16
2. Locate the adjusting screw on the ice maker assembly
control box. The adjusting screw is just below the minus
1
(-) and plus (+) signs on the control box (Figure 16)
.
ULIN_0054_A
Figure 14
NOTE: Make adjustments in small increments. Too
large of an adjustment could cause the unit to
malfunction.
4. Disconnect the hose connector (Figure 14, 1) from the
water solenoid valve (Figure 14, 2)
.
CAUTION
5. DO NOT remove the inlet screen from the water
solenoid valve. Use a tooth brush to gently clean any
sediment from the inlet screen.
Too large of an adjustment to the screw can cause
the water to overflow the ice maker and can cause
property damage.
6. Re-connect the water supply hose connector (Figure
14, 1) to the water solenoid valve (Figure 14, 2)
Tighten the connector securely.
.
3. Turn the adjusting screw toward the minus (-) sign
(clockwise) for smaller cubes or toward the plus (+) sign
(counterclockwise) for larger cubes.
7. Open the water main supply valve and check for
leakage at the water hose connection. Ensure that the
water supply line is not kinked.
4. Install the ice maker assembly cover.
8. Reconnect power to the unit before re-installing.
12
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Alignment Check and Adjustment
IMPORTANT
IMPORTANT
Use only genuine U-Line replacement parts. U-Line
ice maker parts are not the same as standard FSP
Whirlpool parts. Using non U-Line parts can reduce
ice rate, cause water to overflow from ice maker
mold, damage the unit, and may void the warranty.
Properly aligned, the door’s gasket should be firmly
in contact with the cabinet all the way around the
door (no gaps). Carefully examine the door’s gasket
to assure that it is firmly in contact with the
cabinet. Also make sure the door gasket is not
pinched on the hinge side of the door.
Leveling
It is important that units equipped with adjustable feet
are level, for proper door and ice maker (if equipped)
operation.
NOTE: Model CO29 DOES NOT have leveling feet. This
model MUST be placed on a level surface to operate
properly.
To level units with adjustable feet:
ULIN_0210_A
Figure 19
NOTE: Model CO75 shown (Figure 19)
1. Loosen (do not remove) top (Figure 19) and bottom
1
hinge screws.
2. Align door squarely with cabinet.
ULIN_0225_A
3. Make sure gasket is firmly in contact with cabinet all
the way around the door (no gaps).
Figure 17
1. Use a level to check the levelness of the unit from
front to back and from side to side. Level should be
placed along top edge and side edge as shown
(Figure 17, 1).
4. Tighten bottom hinge screws.
5. Tighten top hinge screws.
1
ULIN_0042_A
Figure 18
2. If the unit is not level, adjust the feet on the corners of
the unit as necessary (Figure 18)
.
3. Check the levelness after each adjustment and repeat
the previous steps until the unit is level.
CO29, CO75
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Door Reversal
CO29:
Depending upon the location of the unit, it may be
desirable to change the side on which the door is
mounted. NOTE: On built-in installations, changing the
door mounting to the left side may interfere with ice
bucket removal.
To reverse the door mounting, perform the following:
1
ULIN_0215_A
Figure 22
3. Remove bottom hinge from cabinet (two screws)
(Figure 22)
.
ULIN_0014_A
Figure 20
1. Remove the control knob (Figure 20, 1) by pulling it
away from the cabinet.
2. Remove two grille screws, and remove the grille.
ULINE_0216_A
Figure 23
4. Remove screws on opposite side of cabinet (Figure 23)
Note that there may be a nut behind one or both
screws on either side.
.
ULIN_0210_A
Figure 21
1. Remove top hinge from cabinet (three screws) (Figure
21). Hold door to keep it from falling.
2. Lift the door off the bottom hinge.
ULINE_0217_A
Figure 24
5. Install hinge on opposite side, bottom of cabinet
(Figure 24). Replace nut on back side where installed.
Align hinge outer edge with cabinet before tightening
screws.
14
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
1
ULIN_0109_A
ULIN_0145_A
Figure 25
Figure 28
6. Relocate plastic spacer/bushing (Figure 25, 1) on
bottom of door to opposite side, and place door on
bottom hinge pin. Clean out bushing hole in door
bottom with a screwdriver if needed.
11. Fasten upper hinge to unit (three screws) (Figure 28)
.
Partially tighten screws until door is aligned.
12. Adjust door to assure proper seal. Tighten upper hinge
screws securely.
13. Replace three plastic plugs removed in Step 10 into
holes on top of unit. Replace screws in holes in bottom
of unit, opposite side.
Hinge
Plastic
Plug Hole
Plastic
Plug Hole
14. Re-inspect door seal and alignment. Adjust if needed.
Screw
Right Side
Door Swing
Left Side
Door Swing
Right Side
Hinge
Invert
Screw
Invert
Hinge
ULIN_0142_A
Figure 26
7. Remove plastic hole plug from door handle and
2
1
ULIN_0214_A
relocate on opposite side (Figure 26)
.
8. Remove pivot screw from top hinge, invert screw and
Figure 29
reinstall pivot screw in top hinge (Figure 26)
.
15. Make sure grille cap is behind grille in slots provided in
grille (Figure 29, 1) before attaching grille to unit, and
secure but do not overtighten both grille screws
(Figure 29, 2)
.
16. Install the temperature control knob.
All units may be left- or right-hand opening.
ULIN_0144_A
Figure 27
9. Remove three plastic screw plugs in hinge holes, top of
cabinet, opposite side, being careful not to scratch
cabinet (Figure 27)
.
10. Place door on lower hinge pin. Invert and install upper
hinge on door.
CO29, CO75
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 32
CO75:
NOTE: The grille should not yet be installed. If it has been
installed, remove it for door reversing.
4. Remove four plastic plugs in hinge holes, invert screw
and reinstall pivot screw in top hinge (Figure 32). Do
not install hinge on cabinet at this time.
To reverse the door on black models:
ULIN_0220_A
Figure 33
ULIN_0218_A
Figure 30
5. Remove bottom hinge from cabinet (four screws) and
screws on opposite side of cabinet (Figure 33)
.
1. Remove top hinge from cabinet (four screws) (Figure
30). Hold door to keep it from falling.
6. Remove pivot screw from bottom hinge, invert screw
and reinstall pivot screw in hinge (Figure 32)
.
2. Lift the door off the bottom hinge.
ULIN_0221_A
ULIN_0219_A
Figure 34
7. Install bottom hinge on cabinet, opposite side, aligning
flat edge of hinge with outer edge of unit. Partially
Figure 31
3. Remove four plastic plugs in hinge holes, top of cabinet,
opposite side, being careful not to scratch cabinet
tighten screws (Figure 34)
.
(Figure 31)
.
Hinge
1
Plastic
Plug Hole
Plastic
Plug Hole
Screw
Right Side
Door Swing
Left Side
Door Swing
ULIN_0222_A
Right Side
Hinge
Invert
Screw
Invert
Hinge
Figure 35
ULIN_0106_A
16
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Relocate plastic spacer/bushing on bottom of door to
the opposite side (Figure 35). Clean out bushing hole
in door bottom if necessary.
Glass Shelf Removal/Installation
Remove the shelves as follows:
ULIN_0223_A
Figure 36
9. Place door on lower hinge pin. Align flat edge of top
hinge with outer edge of unit and fasten upper hinge
to unit (four screws). Partially tighten screws (Figure
ULIN_0232_A
Figure 37
36)
.
1. Pull shelf out about 6" until back of shelf clears the
“hump” on the right hand side.
10. Adjust door to assure proper seal. Tighten upper and
lower hinge screws securely.
2. Tilt right hand edge of shelf up and remove shelf from
unit by pulling out.
11. Replace four plastic plugs removed in Step 4 into holes
on top of unit. Replace screws in holes in bottom of unit
on opposite side.
Insert the shelves as follows:
1. Insert shelf at an angle, approximately 15-20°, over the
rib in the side of the unit where you want to place the
shelf. The shelf must be started into the unit at an
angle to clear the door.
2. Continue to slide the shelf into the unit at an angle
until it clears the door.
3. Lower the shelf and push it in completely.
CO29, CO75
17
Download from Www.Somanuals.com. All Manuals Search And Download.
7 Service
Before Calling for Service
If your U-Line product appears to be malfunctioning, read
through the OPERATION section of this guide to ensure
that the function of all controls are clearly understood. If
the malfunction persists, the TROUBLESHOOTING GUIDE
in this guide will assist you in quickly identifying common
problems, and provide information on possible causes and
remedies. Most often, this will resolve the problem
without the need to call for service.
If Service is Required
If you do not understand a troubleshooting remedy, or
your product needs service, contact U-Line Corporation
directly. Contact information appears on the rear cover of
this guide.
You will be asked for your product Model and Serial
Numbers. This information should be recorded inside the
front cover of this guide, following the products original
purchase. It also appears on the Model and Serial number
plate located on the upper right or rear wall of the
interior of your product.
Replacement Parts
When you need replacement parts, always request that
genuine U-Line replacements be used. U-Line products
have been designed and engineered using components
that work efficiently, and provide superior service life and
performance. The use of aftermarket parts or components
may affect the safety, operation, performance or
durability of your product, and may also void its warranty.
18
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Guide
DANGER
ELECTROCUTION HAZARD
Never attempt to repair or perform maintenance on
the unit until the main electrical power has been
disconnected.
Troubleshooting - What to check when problems occur:
PROBLEM
POSSIBLE CAUSE
REMEDY
Unit not cold enough
Door gasket not sealing properly
Adjust door (See MAINTENANCE; DOOR ALIGN, ADJUST,
REVERSE).
Item(s) interfering with door
Dirty condenser coils
Reposition or remove item(s).
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Airflow to front grille blocked
Temperature not set cold enough
Unit is manual defrost model.
Door gasket not sealing properly
Airflow must not be obstructed to front grille (See
OPERATION).
Set control knob to cooler setting (See OPERATION).
Allow 24 hours for temperature to stabilize.
The unit frosts up.
Models CO29 and CO75 are manual defrost (See
MAINTENANCE; DEFROSTING).
Adjust door (See MAINTENANCE; DOOR ALIGN, ADJUST,
REVERSE).
High ambient temperatures or
humidity
Defrost unit manually (See MAINTENANCE;
DEFROSTING).
Water is leaking out the back of the Water supply connection leaking
unit.
Tighten fitting as required.
Ice cubes sticking together
Door gasket not sealing properly
Adjust door (See MAINTENANCE; DOOR ALIGN, ADJUST,
REVERSE).
Infrequent use of cubes
Break apart cubes.
Noise during operation
Copper water supply tubing
contacting internal components
Carefully bend tubing away from cabinet and
components.
Certain sounds are normal.
Soft sounds from the fan and water/dropping sounds
from the ice maker will be heard.
No ice
Bin arm locked in upright position
No water to unit
Lower bin arm.
Turn on water or contact plumber.
Adjust control to a warmer setting (See OPERATION).
Not enough ice
Control set too cold
Ice cube size too large
Set cube size smaller (See MAINTENANCE; ICE MAKER;
ICE CUBE THICKNESS ADJUST).
Dirty condenser coils
Clean condenser (See MAINTENANCE; CONDENSER
CLEANING).
Water leaks into ice bucket.
Water level set too high
Set cube size smaller (See MAINTENANCE; ICE MAKER;
ICE CUBE THICKNESS ADJUST).
Fresh food section on Combo units
too cold
Ice bucket not fully inserted
Flap door not closed correctly
Temperature control set too cold
Push ice bucket into place.
Be sure flap door is closed correctly.
Set control to warmer setting (See OPERATION).
Unit too cold
CO29, CO75
19
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
20
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
CO29, CO75
21
Download from Www.Somanuals.com. All Manuals Search And Download.
This page intentionally left blank
22
CO29, CO75
Download from Www.Somanuals.com. All Manuals Search And Download.
U-Line Corporation Limited Warranty
U-Line Corporation warrants each U-Line product to be free from defects in materials and workmanship for a period of
one year from the date of purchase; and warrants the sealed system (consisting of the compressor, the condenser, the
evaporator, the hot gas bypass valve, the dryer and the connecting tubing) in each U-Line product to be free from
defects in materials and workmanship for a period of five years from the date of purchase. During the initial one-year
warranty period for all U-Line products U-Line shall: (1) at U-Lines option, repair any product or replace any part of a
product that breaches this warranty; and (2) for all Marine, RV and Domestic U-Line products sold and serviced in the
United States (including Alaska and Hawaii) and Canada, U-Line shall cover the labor costs incurred in connection with
the replacement of any defective part. During years two through five of the warranty period for the sealed system, U-
Line shall: (1) repair or replace any part of the sealed system that breaches this warranty; and (2) for all Marine, RV and
Domestic U-Line products sold and serviced in the United States (including Alaska and Hawaii) and Canada, U-Line shall
cover the labor costs incurred in connection with the replacement of any defective part of the sealed system. All other
charges, including transportation charges for replacements under this warranty and labor costs not specifically covered
by this warranty, shall be borne by you. This warranty is extended only to the original purchaser of the U-Line product.
The Registration Card included with the product should be promptly completed by you and mailed back to U-Line or you
The following are excluded from this limited warranty: installation charges; damages caused by disasters or acts of God,
such as fire, floods, wind and lightening; damages incurred or resulting from shipping, improper installation,
unauthorized modification, or misuse/abuse of the product; customer education calls; food loss/spoilage; door and water
level adjustments (except during the first 90 days from the date of purchase); defrosting the product; adjusting the
controls; door reversal; or cleaning the condenser.
If a product defect is discovered during the applicable warranty period, you must promptly notify either the dealer from
whom you purchased the product or U-Line at P.O. Box 245040, Milwaukee, Wisconsin 53224 or at 414-354-0300. In no
event shall such notification be received later than 30 days after the expiration of the applicable warranty period. U-Line
may require that defective parts be returned, at your expense, to U-Lines factory in Milwaukee, Wisconsin, for
inspection. Any action by you for breach of warranty must be commenced within one year after the expiration of the
applicable warranty period.
This limited warranty is in lieu of any other warranty, express or implied, including, but not limited to any
implied warranty of merchantability or fitness for a particular purpose; provided however, that to the
extent required by law, implied warranties are included but do not extend beyond the duration of the
express warranty first set forth above. U-Lines sole liability and your exclusive remedy under this warranty
is set forth in the initial paragraph above. U-Line shall have no liability whatsoever for any incidental,
consequential or special damages arising from the sale, use or installation of the product or from any other
cause whatsoever, whether based on warranty (express or implied) or otherwise based on contract, tort or
any other theory of liability.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or
consequential damages, so the above limitations may not apply to you. This warranty gives you specific legal rights, and
you may also have other rights which vary from state to state.
CO29, CO75
23
Download from Www.Somanuals.com. All Manuals Search And Download.
For General Inquiries:
P.O. Box 245040
Milwaukee, Wisconsin
53224-9540 U.S.A.
Phone (800) 779-2547
FAX (414) 354-5696
For Service and Parts
Assistance:
Phone (800) 779-2547
(414) 354-0300
FAX (414) 354-5696
Email:
E-mail:
For more than four decades, U-Line has distinguished itself as the
leader in built-in under-counter ice making, refrigeration and
wine storage appliances.
An INSTALLATION MANUAL for your unit, providing complete
installation information, is available for download at
including panel size, and instructions are available by visiting
When you need replacement parts, always request genuine U-Line
distributor in your area.
U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in
®
®
undercounter ice makers, Combo ice maker/refrigerators, Wine Captain wine storage units,
refrigerators, refrigerated drawers and refrigerator/freezers.
©2006 U-Line Corporation
Publication No. 30089
01/2006 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|